Vlastimil Babka [Tue, 14 Jan 2020 00:29:20 +0000 (16:29 -0800)]
mm, debug_pagealloc: don't rely on static keys too early
Commit 96a2b03f281d ("mm, debug_pagelloc: use static keys to enable
debugging") has introduced a static key to reduce overhead when
debug_pagealloc is compiled in but not enabled. It relied on the
assumption that jump_label_init() is called before parse_early_param()
as in start_kernel(), so when the "debug_pagealloc=on" option is parsed,
it is safe to enable the static key.
However, it turns out multiple architectures call parse_early_param()
earlier from their setup_arch(). x86 also calls jump_label_init() even
earlier, so no issue was found while testing the commit, but same is not
true for e.g. ppc64 and s390 where the kernel would not boot with
debug_pagealloc=on as found by our QA.
To fix this without tricky changes to init code of multiple
architectures, this patch partially reverts the static key conversion
from 96a2b03f281d. Init-time and non-fastpath calls (such as in arch
code) of debug_pagealloc_enabled() will again test a simple bool
variable. Fastpath mm code is converted to a new
debug_pagealloc_enabled_static() variant that relies on the static key,
which is enabled in a well-defined point in mm_init() where it's
guaranteed that jump_label_init() has been called, regardless of
architecture.
Roman Gushchin [Tue, 14 Jan 2020 00:29:16 +0000 (16:29 -0800)]
mm: memcg/slab: fix percpu slab vmstats flushing
Currently slab percpu vmstats are flushed twice: during the memcg
offlining and just before freeing the memcg structure. Each time percpu
counters are summed, added to the atomic counterparts and propagated up
by the cgroup tree.
The second flushing is required due to how recursive vmstats are
implemented: counters are batched in percpu variables on a local level,
and once a percpu value is crossing some predefined threshold, it spills
over to atomic values on the local and each ascendant levels. It means
that without flushing some numbers cached in percpu variables will be
dropped on floor each time a cgroup is destroyed. And with uptime the
error on upper levels might become noticeable.
The first flushing aims to make counters on ancestor levels more
precise. Dying cgroups may resume in the dying state for a long time.
After kmem_cache reparenting which is performed during the offlining
slab counters of the dying cgroup don't have any chances to be updated,
because any slab operations will be performed on the parent level. It
means that the inaccuracy caused by percpu batching will not decrease up
to the final destruction of the cgroup. By the original idea flushing
slab counters during the offlining should minimize the visible
inaccuracy of slab counters on the parent level.
The problem is that percpu counters are not zeroed after the first
flushing. So every cached percpu value is summed twice. It creates a
small error (up to 32 pages per cpu, but usually less) which accumulates
on parent cgroup level. After creating and destroying of thousands of
child cgroups, slab counter on parent level can be way off the real
value.
For now, let's just stop flushing slab counters on memcg offlining. It
can't be done correctly without scheduling a work on each cpu: reading
and zeroing it during css offlining can race with an asynchronous
update, which doesn't expect values to be changed underneath.
With this change, slab counters on parent level will become eventually
consistent. Once all dying children are gone, values are correct. And
if not, the error is capped by 32 * NR_CPUS pages per dying cgroup.
It's not perfect, as slab are reparented, so any updates after the
reparenting will happen on the parent level. It means that if a slab
page was allocated, a counter on child level was bumped, then the page
was reparented and freed, the annihilation of positive and negative
counter values will not happen until the child cgroup is released. It
makes slab counters different from others, and it might want us to
implement flushing in a correct form again. But it's also a question of
performance: scheduling a work on each cpu isn't free, and it's an open
question if the benefit of having more accurate counters is worth it.
We might also consider flushing all counters on offlining, not only slab
counters.
So let's fix the main problem now: make the slab counters eventually
consistent, so at least the error won't grow with uptime (or more
precisely the number of created and destroyed cgroups). And think about
the accuracy of counters separately.
mm/shmem.c: thp, shmem: fix conflict of above-47bit hint address and PMD alignment
Shmem/tmpfs tries to provide THP-friendly mappings if huge pages are
enabled. But it doesn't work well with above-47bit hint address.
Normally, the kernel doesn't create userspace mappings above 47-bit,
even if the machine allows this (such as with 5-level paging on x86-64).
Not all user space is ready to handle wide addresses. It's known that
at least some JIT compilers use higher bits in pointers to encode their
information.
Userspace can ask for allocation from full address space by specifying
hint address (with or without MAP_FIXED) above 47-bits. If the
application doesn't need a particular address, but wants to allocate
from whole address space it can specify -1 as a hint address.
Unfortunately, this trick breaks THP alignment in shmem/tmp:
shmem_get_unmapped_area() would not try to allocate PMD-aligned area if
*any* hint address specified.
This can be fixed by requesting the aligned area if the we failed to
allocated at user-specified hint address. The request with inflated
length will also take the user-specified hint address. This way we will
not lose an allocation request from the full address space.
mm/huge_memory.c: thp: fix conflict of above-47bit hint address and PMD alignment
Patch series "Fix two above-47bit hint address vs. THP bugs".
The two get_unmapped_area() implementations have to be fixed to provide
THP-friendly mappings if above-47bit hint address is specified.
This patch (of 2):
Filesystems use thp_get_unmapped_area() to provide THP-friendly
mappings. For DAX in particular.
Normally, the kernel doesn't create userspace mappings above 47-bit,
even if the machine allows this (such as with 5-level paging on x86-64).
Not all user space is ready to handle wide addresses. It's known that
at least some JIT compilers use higher bits in pointers to encode their
information.
Userspace can ask for allocation from full address space by specifying
hint address (with or without MAP_FIXED) above 47-bits. If the
application doesn't need a particular address, but wants to allocate
from whole address space it can specify -1 as a hint address.
Unfortunately, this trick breaks thp_get_unmapped_area(): the function
would not try to allocate PMD-aligned area if *any* hint address
specified.
Modify the routine to handle it correctly:
- Try to allocate the space at the specified hint address with length
padding required for PMD alignment.
- If failed, retry without length padding (but with the same hint
address);
- If the returned address matches the hint address return it.
- Otherwise, align the address as required for THP and return.
The user specified hint address is passed down to get_unmapped_area() so
above-47bit hint address will be taken into account without breaking
alignment requirements.
mm/memory_hotplug: don't free usage map when removing a re-added early section
When we remove an early section, we don't free the usage map, as the
usage maps of other sections are placed into the same page. Once the
section is removed, it is no longer an early section (especially, the
memmap is freed). When we re-add that section, the usage map is reused,
however, it is no longer an early section. When removing that section
again, we try to kfree() a usage map that was allocated during early
boot - bad.
Let's check against PageReserved() to see if we are dealing with an
usage map that was allocated during boot. We could also check against
!(PageSlab(usage_page) || PageCompound(usage_page)), but PageReserved() is
cleaner.
Can be triggered using memtrace under ppc64/powernv:
$ mount -t debugfs none /sys/kernel/debug/
$ echo 0x20000000 > /sys/kernel/debug/powerpc/memtrace/enable
$ echo 0x20000000 > /sys/kernel/debug/powerpc/memtrace/enable
------------[ cut here ]------------
kernel BUG at mm/slub.c:3969!
Oops: Exception in kernel mode, sig: 5 [#1]
LE PAGE_SIZE=3D64K MMU=3DHash SMP NR_CPUS=3D2048 NUMA PowerNV
Modules linked in:
CPU: 0 PID: 154 Comm: sh Not tainted 5.5.0-rc2-next-20191216-00005-g0be1dba7b7c0 #61
NIP kfree+0x338/0x3b0
LR section_deactivate+0x138/0x200
Call Trace:
section_deactivate+0x138/0x200
__remove_pages+0x114/0x150
arch_remove_memory+0x3c/0x160
try_remove_memory+0x114/0x1a0
__remove_memory+0x20/0x40
memtrace_enable_set+0x254/0x850
simple_attr_write+0x138/0x160
full_proxy_write+0x8c/0x110
__vfs_write+0x38/0x70
vfs_write+0x11c/0x2a0
ksys_write+0x84/0x140
system_call+0x5c/0x68
---[ end trace 4b053cbd84e0db62 ]---
The first invocation will offline+remove memory blocks. The second
invocation will first add+online them again, in order to offline+remove
them again (usually we are lucky and the exact same memory blocks will
get "reallocated").
Tested on powernv with boot memory: The usage map will not get freed.
Tested on x86-64 with DIMMs: The usage map will get freed.
Using Dynamic Memory under a Power DLAPR can trigger it easily.
Triggering removal (I assume after previously removed+re-added) of
memory from the HMC GUI can crash the kernel with the same call trace
and is fixed by this patch.
Vlastimil Babka [Tue, 14 Jan 2020 00:29:04 +0000 (16:29 -0800)]
mm, thp: tweak reclaim/compaction effort of local-only and all-node allocations
THP page faults now attempt a __GFP_THISNODE allocation first, which
should only compact existing free memory, followed by another attempt
that can allocate from any node using reclaim/compaction effort
specified by global defrag setting and madvise.
This patch makes the following changes to the scheme:
- Before the patch, the first allocation relies on a check for
pageblock order and __GFP_IO to prevent excessive reclaim. This
however affects also the second attempt, which is not limited to
single node.
Instead of that, reuse the existing check for costly order
__GFP_NORETRY allocations, and make sure the first THP attempt uses
__GFP_NORETRY. As a side-effect, all costly order __GFP_NORETRY
allocations will bail out if compaction needs reclaim, while
previously they only bailed out when compaction was deferred due to
previous failures.
This should be still acceptable within the __GFP_NORETRY semantics.
- Before the patch, the second allocation attempt (on all nodes) was
passing __GFP_NORETRY. This is redundant as the check for pageblock
order (discussed above) was stronger. It's also contrary to
madvise(MADV_HUGEPAGE) which means some effort to allocate THP is
requested.
After this patch, the second attempt doesn't pass __GFP_THISNODE nor
__GFP_NORETRY.
To sum up, THP page faults now try the following attempts:
1. local node only THP allocation with no reclaim, just compaction.
2. for madvised VMA's or when synchronous compaction is enabled always - THP
allocation from any node with effort determined by global defrag setting
and VMA madvise
3. fallback to base pages on any node
[CAUSE]
All these call sites are only relying on root->reloc_root, which can
undergo btrfs_drop_snapshot(), and since we don't have real refcount
based protection to reloc roots, we can reach already dropped reloc
root, triggering KASAN.
[FIX]
To avoid such access to unstable root->reloc_root, we should check
BTRFS_ROOT_DEAD_RELOC_TREE bit first.
This patch introduces wrappers that provide the correct way to check the
bit with memory barriers protection.
Most callers don't distinguish merged reloc tree and no reloc tree. The
only exception is should_ignore_root(), as merged reloc tree can be
ignored, while no reloc tree shouldn't.
[CRITICAL SECTION ANALYSIS]
Although test_bit()/set_bit()/clear_bit() doesn't imply a barrier, the
DEAD_RELOC_TREE bit has extra help from transaction as a higher level
barrier, the lifespan of root::reloc_root and DEAD_RELOC_TREE bit are:
NULL: reloc_root is NULL PTR: reloc_root is not NULL
0: DEAD_RELOC_ROOT bit not set DEAD: DEAD_RELOC_ROOT bit set
(NULL, 0) Initial state __
| /\ Section A
btrfs_init_reloc_root() \/
| __
(PTR, 0) reloc_root initialized /\
| |
btrfs_update_reloc_root() | Section B
| |
(PTR, DEAD) reloc_root has been merged \/
| __
=== btrfs_commit_transaction() ====================
| /\
clean_dirty_subvols() |
| | Section C
(NULL, DEAD) reloc_root cleanup starts \/
| __
btrfs_drop_snapshot() /\
| | Section D
(NULL, 0) Back to initial state \/
Every have_reloc_root() or test_bit(DEAD_RELOC_ROOT) caller holds
transaction handle, so none of such caller can cross transaction boundary.
In Section A, every caller just found no DEAD bit, and grab reloc_root.
In the cross section A-B, caller may get no DEAD bit, but since reloc_root
is still completely valid thus accessing reloc_root is completely safe.
No test_bit() caller can cross the boundary of Section B and Section C.
In Section C, every caller found the DEAD bit, so no one will access
reloc_root.
In the cross section C-D, either caller gets the DEAD bit set, avoiding
access reloc_root no matter if it's safe or not. Or caller get the DEAD
bit cleared, then access reloc_root, which is already NULL, nothing will
be wrong.
The memory write barriers are between the reloc_root updates and bit
set/clear, the pairing read side is before test_bit.
Vadim Pasternak [Mon, 13 Jan 2020 16:28:30 +0000 (16:28 +0000)]
Documentation/ABI: Fix documentation inconsistency for mlxreg-io sysfs interfaces
Fix attribute name from "jtag_enable", which described twice to
"cpld3_version", which is expected to be instead of second appearance
of "jtag_enable".
Fixes: 2752e34442b5 ("Documentation/ABI: Add new attribute for mlxreg-io sysfs interfaces") Signed-off-by: Vadim Pasternak <[email protected]> Signed-off-by: Andy Shevchenko <[email protected]>
Florian Westphal [Sat, 11 Jan 2020 22:19:53 +0000 (23:19 +0100)]
netfilter: arp_tables: init netns pointer in xt_tgdtor_param struct
An earlier commit (1b789577f655060d98d20e,
"netfilter: arp_tables: init netns pointer in xt_tgchk_param struct")
fixed missing net initialization for arptables, but turns out it was
incomplete. We can get a very similar struct net NULL deref during
error unwinding:
Stephen Boyd [Mon, 13 Jan 2020 17:55:41 +0000 (09:55 -0800)]
Merge tag 'sunxi-clk-fixes-for-5.5' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into clk-fixes
Pull Allwinner clk fixes from Maxime Ripard:
Our usual set of fixes for Allwinner, to fix the number of reported
clocks on the v3s, fixing the external clock on the R40, and some
fixes for the AR100 co-processor clocks.
* tag 'sunxi-clk-fixes-for-5.5' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
clk: sunxi-ng: h6-r: Fix AR100/R_APB2 parent order
clk: sunxi-ng: h6-r: Simplify R_APB1 clock definition
clk: sunxi-ng: sun8i-r: Fix divider on APB0 clock
clk: sunxi-ng: r40: Allow setting parent rate for external clock outputs
clk: sunxi-ng: v3s: Fix incorrect number of hw_clks.
Cong Wang [Fri, 10 Jan 2020 19:53:08 +0000 (11:53 -0800)]
netfilter: fix a use-after-free in mtype_destroy()
map->members is freed by ip_set_free() right before using it in
mtype_ext_cleanup() again. So we just have to move it down.
Reported-by: [email protected] Fixes: 40cd63bf33b2 ("netfilter: ipset: Support extensions which need a per data destroy function") Acked-by: Jozsef Kadlecsik <[email protected]> Signed-off-by: Cong Wang <[email protected]> Signed-off-by: Pablo Neira Ayuso <[email protected]>
Kristian Evensen [Mon, 13 Jan 2020 14:14:05 +0000 (15:14 +0100)]
USB: serial: option: Add support for Quectel RM500Q
RM500Q is a 5G module from Quectel, supporting both standalone and
non-standalone modes. Unlike other recent Quectel modems, it is possible
to identify the diagnostic interface (bInterfaceProtocol is unique).
Thus, there is no need to check for the number of endpoints or reserve
interfaces. The interface number is still dynamic though, so matching on
interface number is not possible and two entries have to be added to the
table.
Output from usb-devices with all interfaces enabled (order is diag,
nmea, at_port, modem, rmnet and adb):
Bus 004 Device 007: ID 2c7c:0800 Quectel Wireless Solutions Co., Ltd.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 3.20
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 9
idVendor 0x2c7c Quectel Wireless Solutions Co., Ltd.
idProduct 0x0800
bcdDevice 4.14
iManufacturer 1 Quectel
iProduct 2 LTE-A Module
iSerial 3 40046d60
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 328
bNumInterfaces 6
bConfigurationValue 1
iConfiguration 4 DIAG_SER_RMNET
bmAttributes 0xa0
(Bus Powered)
Remote Wakeup
MaxPower 224mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 48
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
** UNRECOGNIZED: 05 24 00 10 01
** UNRECOGNIZED: 05 24 01 00 00
** UNRECOGNIZED: 04 24 02 02
** UNRECOGNIZED: 05 24 06 00 00
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x000a 1x 10 bytes
bInterval 9
bMaxBurst 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 2
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
** UNRECOGNIZED: 05 24 00 10 01
** UNRECOGNIZED: 05 24 01 00 00
** UNRECOGNIZED: 04 24 02 02
** UNRECOGNIZED: 05 24 06 00 00
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x85 EP 5 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x000a 1x 10 bytes
bInterval 9
bMaxBurst 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x84 EP 4 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 3
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
** UNRECOGNIZED: 05 24 00 10 01
** UNRECOGNIZED: 05 24 01 00 00
** UNRECOGNIZED: 04 24 02 02
** UNRECOGNIZED: 05 24 06 00 00
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x87 EP 7 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x000a 1x 10 bytes
bInterval 9
bMaxBurst 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x86 EP 6 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 4
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 5 CDEV Serial
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x88 EP 8 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 9
bMaxBurst 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x8e EP 14 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 6
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x0f EP 15 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 2
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 5
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 66
bInterfaceProtocol 1
iInterface 6 ADB Interface
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x05 EP 5 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x89 EP 9 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 0
Binary Object Store Descriptor:
bLength 5
bDescriptorType 15
wTotalLength 42
bNumDeviceCaps 3
USB 2.0 Extension Device Capability:
bLength 7
bDescriptorType 16
bDevCapabilityType 2
bmAttributes 0x00000006
Link Power Management (LPM) Supported
SuperSpeed USB Device Capability:
bLength 10
bDescriptorType 16
bDevCapabilityType 3
bmAttributes 0x00
wSpeedsSupported 0x000f
Device can operate at Low Speed (1Mbps)
Device can operate at Full Speed (12Mbps)
Device can operate at High Speed (480Mbps)
Device can operate at SuperSpeed (5Gbps)
bFunctionalitySupport 1
Lowest fully-functional device speed is Full Speed (12Mbps)
bU1DevExitLat 1 micro seconds
bU2DevExitLat 500 micro seconds
** UNRECOGNIZED: 14 10 0a 00 01 00 00 00 00 11 00 00 30 40 0a 00 b0 40 0a 00
Device Status: 0x0000
(Bus Powered)
Stephan Gerhold [Sun, 5 Jan 2020 10:27:53 +0000 (11:27 +0100)]
ASoC: msm8916-wcd-digital: Reset RX interpolation path after use
For some reason, attempting to route audio through QDSP6 on MSM8916
causes the RX interpolation path to get "stuck" after playing audio
a few times. In this situation, the analog codec part is still working,
but the RX path in the digital codec stops working, so you only hear
the analog parts powering up. After a reboot everything works again.
So far I was not able to reproduce the problem when using lpass-cpu.
The downstream kernel driver avoids this by resetting the RX
interpolation path after use. In mainline we do something similar
for the TX decimator (LPASS_CDC_CLK_TX_RESET_B1_CTL), but the
interpolator reset (LPASS_CDC_CLK_RX_RESET_CTL) got lost when the
msm8916-wcd driver was split into analog and digital.
Fix this problem by adding the reset to
msm8916_wcd_digital_enable_interpolator().
Stephan Gerhold [Sat, 11 Jan 2020 16:40:04 +0000 (17:40 +0100)]
ASoC: msm8916-wcd-analog: Fix MIC BIAS Internal1
MIC BIAS Internal1 is broken at the moment because we always
enable the internal rbias resistor to the TX2 line (connected to
the headset microphone), rather than enabling the resistor connected
to TX1.
Move the RBIAS code to pm8916_wcd_analog_enable_micbias_int1/2()
to fix this.
Stephan Gerhold [Sat, 11 Jan 2020 16:40:03 +0000 (17:40 +0100)]
ASoC: msm8916-wcd-analog: Fix selected events for MIC BIAS External1
MIC BIAS External1 sets pm8916_wcd_analog_enable_micbias_ext1()
as event handler, which ends up in pm8916_wcd_analog_enable_micbias_ext().
But pm8916_wcd_analog_enable_micbias_ext() only handles the POST_PMU
event, which is not specified in the event flags for MIC BIAS External1.
This means that the code in the event handler is never actually run.
Set SND_SOC_DAPM_POST_PMU as the only event for the handler to fix this.
Kai Vehmanen [Fri, 10 Jan 2020 23:57:51 +0000 (17:57 -0600)]
ASoC: hdac_hda: Fix error in driver removal after failed probe
In case system has multiple HDA codecs, and codec probe fails for
at least one but not all codecs, driver will end up cancelling
a non-initialized timer context upon driver removal.
In case system has multiple HDA controllers, it can happen that
same HDA codec driver is used for codecs of multiple controllers.
In this case, SOF may fail to probe the HDA driver and SOF
initialization fails.
SOF HDA code currently relies that a call to request_module() will
also run device matching logic to attach driver to the codec instance.
However if driver for another HDA controller was already loaded and it
already loaded the HDA codec driver, this breaks current logic in SOF.
In this case the request_module() SOF does becomes a no-op and HDA
Codec driver is not attached to the codec instance sitting on the HDA
bus SOF is controlling. Typical scenario would be a system with both
external and internal GPUs, with driver of the external GPU loaded
first.
Fix this by adding similar logic as is used in legacy HDA driver
where an explicit device_attach() call is done after request_module().
Also add logic to propagate errors reported by device_attach() back
to caller. This also works in the case where drivers are not built
as modules.
Bard liao [Fri, 10 Jan 2020 23:57:48 +0000 (17:57 -0600)]
ASoC: SOF: Intel: lower print level to dbg if we will reinit DSP
We will reinit DSP in a loop when it fails to initialize the first
time, as recommended. So, it is not an error before we finally give
up. And reorder the trace to make it more readable.
Tobias Schramm [Thu, 9 Jan 2020 07:31:29 +0000 (08:31 +0100)]
drm/rockchip: fix integer type used for storing dp data rate
commit 2589c4025f13 ("drm/rockchip: Avoid drm_dp_link helpers") changes
the type of variables used to store the display port data rate and
number of lanes to u8. However u8 is not sufficient to store the link
data rate of the display port.
This commit reverts the type of data rate to unsigned int.
Chris Wilson [Fri, 10 Jan 2020 11:04:02 +0000 (11:04 +0000)]
drm/i915/gt: Mark ring->vma as active while pinned
As we use the active state to keep the vma alive while we are reading
its contents during GPU error capture, we need to mark the
ring->vma as active during execution if we want to include the rinbuffer
in the error state.
Chris Wilson [Fri, 10 Jan 2020 11:04:01 +0000 (11:04 +0000)]
drm/i915/gt: Mark context->state vma as active while pinned
As we use the active state to keep the vma alive while we are reading
its contents during GPU error capture, we need to mark the
context->state vma as active during execution if we want to include it
in the error state.
Chris Wilson [Fri, 10 Jan 2020 11:04:00 +0000 (11:04 +0000)]
drm/i915/gt: Skip trying to unbind in restore_ggtt_mappings
Currently we first to try to unbind the VMA (and lazily rebind on next
use) as an optimisation during restore_ggtt_mappings. Ideally, the only
objects in the GGTT upon resume are the pinned kernel objects which
can't be unbound and need to be restored. As the unbind interferes with
the plan to mark those objects as active for error capture, forgo the
optimisation.
YueHaibing [Tue, 7 Jan 2020 13:50:14 +0000 (21:50 +0800)]
drm/i915: Add missing include file <linux/math64.h>
Fix build error:
./drivers/gpu/drm/i915/selftests/i915_random.h: In function i915_prandom_u32_max_state:
./drivers/gpu/drm/i915/selftests/i915_random.h:48:23: error:
implicit declaration of function mul_u32_u32; did you mean mul_u64_u32_div? [-Werror=implicit-function-declaration]
return upper_32_bits(mul_u32_u32(prandom_u32_state(state), ep_ro));
Guido Günther [Fri, 27 Dec 2019 10:22:54 +0000 (11:22 +0100)]
iio: light: vcnl4000: Fix scale for vcnl4040
According to the data sheet the ambient sensor's scale is 0.12 lux/step
(not 0.024 lux/step as used by vcnl4200) when the integration time is
80ms. The integration time is currently hardcoded in the driver to that
value.
See p. 8 in https://www.vishay.com/docs/84307/designingvcnl4040.pdf
Lars Möllendorf [Fri, 13 Dec 2019 13:50:55 +0000 (14:50 +0100)]
iio: buffer: align the size of scan bytes to size of the largest element
Previous versions of `iio_compute_scan_bytes` only aligned each element
to its own length (i.e. its own natural alignment). Because multiple
consecutive sets of scan elements are buffered this does not work in
case the computed scan bytes do not align with the natural alignment of
the first scan element in the set.
This commit fixes this by aligning the scan bytes to the natural
alignment of the largest scan element in the set.
IIO triggered buffer depends on IIO buffer which is missing from Kconfig
file. This should go unnoticed most of the time because there's a
chance something else has already enabled buffers. In some rare cases
though one might experience kbuild warnings about unmet direct
dependencies and build failures due to missing symbols.
Stephan Gerhold [Mon, 16 Dec 2019 12:41:20 +0000 (13:41 +0100)]
iio: imu: st_lsm6dsx: Fix selection of ST_LSM6DS3_ID
At the moment, attempting to probe a device with ST_LSM6DS3_ID
(e.g. using the st,lsm6ds3 compatible) fails with:
st_lsm6dsx_i2c 1-006b: unsupported whoami [69]
... even though 0x69 is the whoami listed for ST_LSM6DS3_ID.
This happens because st_lsm6dsx_check_whoami() also attempts
to match unspecified (zero-initialized) entries in the "id" array.
ST_LSM6DS3_ID = 0 will therefore match any entry in
st_lsm6dsx_sensor_settings (here: the first), because none of them
actually have all 12 entries listed in the "id" array.
Avoid this by additionally checking if "name" is set,
which is only set for valid entries in the "id" array.
Note: Although the problem was introduced earlier it did not surface until
commit 52f4b1f19679 ("iio: imu: st_lsm6dsx: add support for accel/gyro unit of lsm9ds1")
because ST_LSM6DS3_ID was the first entry in st_lsm6dsx_sensor_settings.
This patch fixes device tree channel configuration.
ad7124 driver reads channels configuration from the device tree.
It expects to find channel specifications as child nodes.
Before this patch ad7124 driver assumed that the child nodes are parsed
by for_each_available_child_of_node in the order 0,1,2,3...
This is wrong and the real order of the children can be seen by running:
dtc -I fs /sys/firmware/devicetree/base on the machine.
For example, running this on an rpi 3B+ yields the real
children order: 4,2,0,7,5,3,1,6
Before this patch the driver assigned the channel configuration
like this:
- 0 <- 4
- 1 <- 2
- 2 <- 0
........
For example, the symptoms can be observed by connecting the 4th channel
to a 1V tension and then reading the in_voltage0-voltage19_raw sysfs
(multiplied of course by the scale) one would see that channel 0
measures 1V and channel 4 measures only noise.
Now the driver uses the reg property of each child in order to
correctly identify to which channel the parsed configuration
belongs to.
Jian-Hong Pan [Mon, 30 Dec 2019 08:30:45 +0000 (16:30 +0800)]
platform/x86: asus-wmi: Fix keyboard brightness cannot be set to 0
Some of ASUS laptops like UX431FL keyboard backlight cannot be set to
brightness 0. According to ASUS' information, the brightness should be
0x80 ~ 0x83. This patch fixes it by following the logic.
Fixes: e9809c0b9670 ("asus-wmi: add keyboard backlight support") Signed-off-by: Jian-Hong Pan <[email protected]> Reviewed-by: Daniel Drake <[email protected]> Signed-off-by: Andy Shevchenko <[email protected]>
Hans de Goede [Mon, 6 Jan 2020 14:42:19 +0000 (15:42 +0100)]
platform/x86: GPD pocket fan: Allow somewhat lower/higher temperature limits
Allow the user to configure the fan to turn on / speed-up at lower
thresholds then before (20 degrees Celcius as minimum instead of 40) and
likewise also allow the user to delay the fan speeding-up till the
temperature hits 90 degrees Celcius (was 70).
Hans de Goede [Mon, 6 Jan 2020 14:42:18 +0000 (15:42 +0100)]
platform/x86: GPD pocket fan: Use default values when wrong modparams are given
Use our default values when wrong module-parameters are given, instead of
refusing to load. Refusing to load leaves the fan at the BIOS default
setting, which is "Off". The CPU's thermal throttling should protect the
system from damage, but not-loading is really not the best fallback in this
case.
This commit fixes this by re-setting module-parameter values to their
defaults if they are out of range, instead of failing the probe with
-EINVAL.
Liming Sun [Fri, 20 Dec 2019 17:04:33 +0000 (12:04 -0500)]
platform/mellanox: fix potential deadlock in the tmfifo driver
This commit fixes the potential deadlock caused by the console Rx
and Tx processing at the same time. Rx and Tx both take the console
and tmfifo spinlock but in different order which causes potential
deadlock. The fix is to use different tmfifo spinlock for Rx and
Tx since they protect different resources and it's safe to split
the lock.
Below is the reported call trace when copying/pasting large string
in the console.
Nishad Kamdar [Thu, 19 Dec 2019 14:30:01 +0000 (20:00 +0530)]
platform/x86: intel-ips: Use the correct style for SPDX License Identifier
This patch corrects the SPDX License Identifier style in
header files related to x86 Platform Specific Drivers.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Linus Torvalds [Mon, 13 Jan 2020 00:48:39 +0000 (16:48 -0800)]
Merge tag 'riscv/for-v5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Paul Walmsley:
"Two fixes for RISC-V:
- Clear FP registers during boot when FP support is present, rather
than when they aren't present
- Move the header files associated with the SiFive L2 cache
controller to drivers/soc (where the code was recently moved)"
* tag 'riscv/for-v5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Fixup obvious bug for fp-regs reset
riscv: move sifive_l2_cache.h to include/soc
Guo Ren [Sun, 5 Jan 2020 02:52:14 +0000 (10:52 +0800)]
riscv: Fixup obvious bug for fp-regs reset
CSR_MISA is defined in Privileged Architectures' spec: 3.1.1 Machine
ISA Register misa. Every bit:1 indicate a feature, so we should beqz
reset_done when there is no F/D bit in csr_misa register.
Signed-off-by: Guo Ren <[email protected]>
[[email protected]: fix typo in commit message] Fixes: 9e80635619b51 ("riscv: clear the instruction cache and all registers when booting") Signed-off-by: Paul Walmsley <[email protected]>
Yash Shah [Wed, 8 Jan 2020 06:09:06 +0000 (22:09 -0800)]
riscv: move sifive_l2_cache.h to include/soc
The commit 9209fb51896f ("riscv: move sifive_l2_cache.c to drivers/soc")
moves the sifive L2 cache driver to driver/soc. It did not move the
header file along with the driver. Therefore this patch moves the header
file to driver/soc
Linus Torvalds [Sun, 12 Jan 2020 17:35:42 +0000 (09:35 -0800)]
Merge tag 'iommu-fixes-v5.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
- Two fixes for VT-d and generic IOMMU code to fix teardown on error
handling code paths.
- Patch for the Intel VT-d driver to fix handling of non-PCI devices
- Fix W=1 compile warning in dma-iommu code
* tag 'iommu-fixes-v5.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/dma: fix variable 'cookie' set but not used
iommu/vt-d: Unlink device if failed to add to group
iommu: Remove device link to group on failure
iommu/vt-d: Fix adding non-PCI devices to Intel IOMMU
Martin KaFai Lau [Fri, 10 Jan 2020 23:16:44 +0000 (15:16 -0800)]
bpftool: Fix printing incorrect pointer in btf_dump_ptr
For plain text output, it incorrectly prints the pointer value
"void *data". The "void *data" is actually pointing to memory that
contains a bpf-map's value. The intention is to print the content of
the bpf-map's value instead of printing the pointer pointing to the
bpf-map's value.
In this case, a member of the bpf-map's value is a pointer type.
Thus, it should print the "*(void **)data".
Linus Torvalds [Sat, 11 Jan 2020 23:40:43 +0000 (15:40 -0800)]
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Two driver bugfixes, a documentation fix, and a removal of a spec
violation for the bus recovery algorithm in the core"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: fix bus recovery stop mode timing
i2c: bcm2835: Store pointer to bus clock
dt-bindings: i2c: at91: fix i2c-sda-hold-time-ns documentation for sam9x60
i2c: at91: fix clk_offset for sam9x60
Linus Torvalds [Sat, 11 Jan 2020 23:33:48 +0000 (15:33 -0800)]
Merge tag 'clone3-tls-v5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux
Pull thread fixes from Christian Brauner:
"This contains a series of patches to fix CLONE_SETTLS when used with
clone3().
The clone3() syscall passes the tls argument through struct clone_args
instead of a register. This means, all architectures that do not
implement copy_thread_tls() but still support CLONE_SETTLS via
copy_thread() expecting the tls to be located in a register argument
based on clone() are currently unfortunately broken. Their tls value
will be garbage.
The patch series fixes this on all architectures that currently define
__ARCH_WANT_SYS_CLONE3. It also adds a compile-time check to ensure
that any architecture that enables clone3() in the future is forced to
also implement copy_thread_tls().
My ultimate goal is to get rid of the copy_thread()/copy_thread_tls()
split and just have copy_thread_tls() at some point in the not too
distant future (Maybe even renaming copy_thread_tls() back to simply
copy_thread() once the old function is ripped from all arches). This
is dependent now on all arches supporting clone3().
While all relevant arches do that now there are still four missing:
ia64, m68k, sh and sparc. They have the system call reserved, but not
implemented. Once they all implement clone3() we can get rid of
ARCH_WANT_SYS_CLONE3 and HAVE_COPY_THREAD_TLS.
This series also includes a minor fix for the arm64 uapi headers which
caused __NR_clone3 to be missing from the exported user headers.
Unfortunately the series came in a little late especially given that
it touches a range of architectures. Due to the holidays not all arch
maintainers responded in time probably due to their backlog. Will and
Arnd have thankfully acked the arm specific changes.
Given that the changes are straightforward and rather minimal combined
with the fact the that clone3() with CLONE_SETTLS is broken I decided
to send them post rc3 nonetheless"
* tag 'clone3-tls-v5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
um: Implement copy_thread_tls
clone3: ensure copy_thread_tls is implemented
xtensa: Implement copy_thread_tls
riscv: Implement copy_thread_tls
parisc: Implement copy_thread_tls
arm: Implement copy_thread_tls
arm64: Implement copy_thread_tls
arm64: Move __ARCH_WANT_SYS_CLONE3 definition to uapi headers
Jacob Keller [Thu, 9 Jan 2020 19:08:20 +0000 (11:08 -0800)]
devlink: correct misspelling of snapshot
The function to obtain a unique snapshot id was mistakenly typo'd as
devlink_region_shapshot_id_get. Fix this typo by renaming the function
and all of its users.
Takashi Iwai [Thu, 9 Jan 2020 08:20:00 +0000 (09:20 +0100)]
ALSA: hda: Rename back to dmic_detect option
We've got quite a few bug reports showing the SOF driver being loaded
unintentionally recently, and the reason seems to be that users didn't
know the module option change: with the recent kernel, a new option
dsp_driver=1 has to be passed to a new module snd-intel-dspcfg
instead of snd_hda_intel.dmic_detect=0 option.
That is, actually there are two tricky things here:
- We changed the whole detection in another module and another
option semantics.
- The existing option for skipping the DSP probe was also renamed.
For avoiding the confusion and giving user more hint, this patch
reverts the renamed option dsp_driver back to dmic_detect for
snd-hda-intel module, and show the warning about the module option
change when the non-default value is passed.
David S. Miller [Sat, 11 Jan 2020 07:32:54 +0000 (23:32 -0800)]
Merge branch 'DP83822-and-DP83TC811-Fixes'
Dan Murphy says:
====================
DP83822 and DP83TC811 Fixes
Two fixes on net/phy/Kconfig for the TI ethernet PHYs.
First fixed the typo in the Kconfig for the DP83TC811 where it incorretly stated
that the support was for a DP83TC822 which does not exist.
Second fix was to update the DP83822 Kconfig entry to indicate support for the
DP83825 devices in the description and the prompt.
====================
Dan Murphy [Fri, 10 Jan 2020 20:03:57 +0000 (14:03 -0600)]
net: phy: DP83822: Update Kconfig with DP83825I support
Update the Kconfig description to indicate support for the DP83825I
device as well.
Fixes: 32b12dc8fde1 ("net: phy: Add DP83825I to the DP83822 driver") Reviewed-by: Andrew Lunn <[email protected]> Signed-off-by: Dan Murphy <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Dan Murphy [Fri, 10 Jan 2020 20:03:56 +0000 (14:03 -0600)]
net: phy: DP83TC811: Fix typo in Kconfig
Fix typo in the Kconfig for the DP83TC811 as it indicates support for
the DP83TC822 which is incorrect.
Fixes: 6d749428788b {"net: phy: DP83TC811: Introduce support for the DP83TC811 phy") Reviewed-by: Andrew Lunn <[email protected]> Signed-off-by: Dan Murphy <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Olof Johansson [Sat, 11 Jan 2020 06:12:16 +0000 (22:12 -0800)]
Merge tag 'imx-fixes-5.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.5, round 2:
- Fix i.MX8MM SDMA1 AHB clock setting to remove a "Timeout waiting for CH0"
error seen with UART1.
- Correct compatible of RV3029 RTC device on imx6q-dhcom board.
- Correct interrupt trigger type for magnetometer on board
imx8mq-librem5-devkit.
- A series from Anson Huang to fix vdd3p0 power supplier for a few NXP
development board.
- Fix imx6q-icore-mipi board to use 1.5 version of i.Core MX6DL, so
that Ethernet interface on the board works properly.
- Fix Toradex Colibri board to get NAND flash support back.
- Fix SGTL5000 VDDIO regulator connection for imx6q-dhcom, which
is connected to PMIC SW2 output rather than a fixed 3V3 rail.
- Fix 'reg' of CPU node on imx7ulp to get rid of a warning given by
kernel.
- Fix endian setting for DCFG on LS1028A SoC, so that register access
of DCFG becomes correct.
* tag 'imx-fixes-5.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx7: Fix Toradex Colibri iMX7S 256MB NAND flash support
ARM: dts: imx6sll-evk: Remove incorrect power supply assignment
ARM: dts: imx6sl-evk: Remove incorrect power supply assignment
ARM: dts: imx6sx-sdb: Remove incorrect power supply assignment
ARM: dts: imx6qdl-sabresd: Remove incorrect power supply assignment
ARM: dts: imx6q-icore-mipi: Use 1.5 version of i.Core MX6DL
arm64: dts: imx8mq-librem5-devkit: use correct interrupt for the magnetometer
ARM: dts: imx6q-dhcom: Fix SGTL5000 VDDIO regulator connection
ARM: dts: imx7ulp: fix reg of cpu node
arm64: dts: imx8mm: Change SDMA1 ahb clock for imx8mm
arm64: dts: ls1028a: fix endian setting for dcfg
ARM: dts: imx6q-dhcom: fix rtc compatible
Ido Schimmel [Thu, 9 Jan 2020 17:57:41 +0000 (19:57 +0200)]
devlink: Wait longer before warning about unset port type
The commit cited below causes devlink to emit a warning if a type was
not set on a devlink port for longer than 30 seconds to "prevent
misbehavior of drivers". This proved to be problematic when
unregistering the backing netdev. The flow is always:
devlink_port_type_clear() // schedules the warning
unregister_netdev() // blocking
devlink_port_unregister() // cancels the warning
The call to unregister_netdev() can block for long periods of time for
various reasons: RTNL lock is contended, large amounts of configuration
to unroll following dismantle of the netdev, etc. This results in
devlink emitting a warning despite the driver behaving correctly.
In emulated environments (of future hardware) which are usually very
slow, the warning can also be emitted during port creation as more than
30 seconds can pass between the time the devlink port is registered and
when its type is set.
In addition, syzbot has hit this warning [1] 1974 times since 07/11/19
without being able to produce a reproducer. Probably because
reproduction depends on the load or other bugs (e.g., RTNL not being
released).
To prevent bogus warnings, increase the timeout to 1 hour.
The EC on the Wilco platform responds with 0xFF to commands related to
the keyboard backlight on the absence of a keyboard backlight module.
This change allows the EC driver to continue loading even if the
backlight module is not present.
Fixes: 119a3cb6d687 ("platform/chrome: wilco_ec: Add keyboard backlight LED support") Signed-off-by: Daniel Campello <[email protected]> Signed-off-by: Enric Balletbo i Serra <[email protected]> Signed-off-by: Benson Leung <[email protected]>
Linus Torvalds [Fri, 10 Jan 2020 21:29:40 +0000 (13:29 -0800)]
Merge tag 'usb-5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY fixes from Greg KH:
"Here are a number of USB and PHY driver fixes for 5.5-rc6
Nothing all that unusual, just the a bunch of small fixes for a lot of
different reported issues. The PHY driver fixes are in here as they
interacted with the usb drivers.
Full details of the patches are in the shortlog, and all of these have
been in linux-next with no reported issues"
* tag 'usb-5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (24 commits)
usb: missing parentheses in USE_NEW_SCHEME
usb: ohci-da8xx: ensure error return on variable error is set
usb: musb: Disable pullup at init
usb: musb: fix idling for suspend after disconnect interrupt
usb: typec: ucsi: Fix the notification bit offsets
USB: Fix: Don't skip endpoint descriptors with maxpacket=0
USB-PD tcpm: bad warning+size, PPS adapters
phy/rockchip: inno-hdmi: round clock rate down to closest 1000 Hz
usb: chipidea: host: Disable port power only if previously enabled
usb: cdns3: should not use the same dev_id for shared interrupt handler
usb: dwc3: gadget: Fix request complete check
usb: musb: dma: Correct parameter passed to IRQ handler
usb: musb: jz4740: Silence error if code is -EPROBE_DEFER
usb: udc: tegra: select USB_ROLE_SWITCH
USB: core: fix check for duplicate endpoints
phy: cpcap-usb: Drop extra write to usb2 register
phy: cpcap-usb: Improve host vs docked mode detection
phy: cpcap-usb: Prevent USB line glitches from waking up modem
phy: mapphone-mdm6600: Fix uninitialized status value regression
phy: cpcap-usb: Fix flakey host idling and enumerating of devices
...
Linus Torvalds [Fri, 10 Jan 2020 21:25:24 +0000 (13:25 -0800)]
Merge tag 'char-misc-5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc fix from Greg KH:
"Here is a single fix, for the chrdev core, for 5.5-rc6
There's been a long-standing race condition triggered by syzbot, and
occasionally real people, in the chrdev open() path. Will finally took
the time to track it down and fix it for real before the holidays.
Here's that one patch, it's been in linux-next for a while with no
reported issues and it does fix the reported problem"
* tag 'char-misc-5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
chardev: Avoid potential use-after-free in 'chrdev_open()'
Linus Torvalds [Fri, 10 Jan 2020 21:22:11 +0000 (13:22 -0800)]
Merge tag 'staging-5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging fixes from Greg KH:
"Here are some small staging driver fixes for 5.5-rc6.
Nothing major here, just some small fixes for a comedi driver, the
vt6656 driver, and a new device id for the rtl8188eu driver.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: rtl8188eu: Add device code for TP-Link TL-WN727N v5.21
staging: comedi: adv_pci1710: fix AI channels 16-31 for PCI-1713
staging: vt6656: set usb_set_intfdata on driver fail.
staging: vt6656: remove bool from vnt_radio_power_on ret
staging: vt6656: limit reg output to block size
staging: vt6656: correct return of vnt_init_registers.
staging: vt6656: Fix non zero logical return of, usb_control_msg
Linus Torvalds [Fri, 10 Jan 2020 21:17:21 +0000 (13:17 -0800)]
Merge tag 'tty-5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are two tty/serial driver fixes for 5.5-rc6.
The first fixes a much much reported issue with a previous tty port
link patch that is in your tree, and the second fixes a problem where
the serdev driver would claim ACPI devices that it shouldn't be
claiming.
Both have been in linux-next for a while with no reported issues"
* tag 'tty-5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serdev: Don't claim unsupported ACPI serial devices
tty: always relink the port
Linus Torvalds [Fri, 10 Jan 2020 20:05:26 +0000 (12:05 -0800)]
Merge tag 'block-5.5-2020-01-10' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A few fixes that should go into this round.
This pull request contains two NVMe fixes via Keith, removal of a dead
function, and a fix for the bio op for read truncates (Ming)"
* tag 'block-5.5-2020-01-10' of git://git.kernel.dk/linux-block:
nvmet: fix per feat data len for get_feature
nvme: Translate more status codes to blk_status_t
fs: move guard_bio_eod() after bio_set_op_attrs
block: remove unused mp_bvec_last_segment
SPI-NOR:
- Add a flag to fix interaction with Micron parts"
* tag 'mtd/fixes-for-5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: spi-nor: Fix the writing of the Status Register on micron flashes
mtd: sm_ftl: fix NULL pointer warning
mtd: onenand: omap2: Pass correct flags for prep_dma_memcpy
mtd: onenand: samsung: Fix iomem access with regular memcpy
mtd: onenand: omap2: Fix errors in style
mtd: cadence: Fix cast to pointer from integer of different size warning
mtd: rawnand: stm32_fmc2: avoid to lock the CPU bus
Linus Torvalds [Fri, 10 Jan 2020 19:46:59 +0000 (11:46 -0800)]
Merge tag 'pm-5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"Prevent the cpufreq-dt driver from probing Tegra20/30 (Dmitry
Osipenko) and prevent the Intel RAPL power capping driver from
crashing during CPU initialization due to a NULL pointer dereference
if the processor model in use is not known to it (Harry Pan)"
* tag 'pm-5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
powercap: intel_rapl: add NULL pointer check to rapl_mmio_cpu_online()
cpufreq: dt-platdev: Blacklist NVIDIA Tegra20 and Tegra30 SoCs
David Ahern [Fri, 10 Jan 2020 17:03:58 +0000 (09:03 -0800)]
ipv4: Detect rollover in specific fib table dump
Sven-Haegar reported looping on fib dumps when 255.255.255.255 route has
been added to a table. The looping is caused by the key rolling over from FFFFFFFF to 0. When dumping a specific table only, we need a means to detect
when the table dump is done. The key and count saved to cb args are both 0
only at the start of the table dump. If key is 0 and count > 0, then we are
in the rollover case. Detect and return to avoid looping.
This only affects dumps of a specific table; for dumps of all tables
(the case prior to the change in the Fixes tag) inet_dump_fib moved
the entry counter to the next table and reset the cb args used by
fib_table_dump and fn_trie_dump_leaf, so the rollover ffffffff back
to 0 did not cause looping with the dumps.
Fixes: effe67926624 ("net: Enable kernel side filtering of route dumps") Reported-by: Sven-Haegar Koch <[email protected]> Signed-off-by: David Ahern <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Jose Abreu [Fri, 10 Jan 2020 15:23:53 +0000 (16:23 +0100)]
net: stmmac: tc: Do not setup flower filtering if RSS is enabled
RSS, when enabled, will bypass the L3 and L4 filtering causing it not
to work. Add a check before trying to setup the filters.
Fixes: 425eabddaf0f ("net: stmmac: Implement L3/L4 Filters using TC Flower") Signed-off-by: Jose Abreu <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Jose Abreu [Fri, 10 Jan 2020 15:23:52 +0000 (16:23 +0100)]
net: stmmac: selftests: Update status when disabling RSS
We are disabling RSS on HW but not updating the internal private status
to the 'disabled' state. This is needed for next tc commit that will
check if RSS is disabled before trying to apply filters.
Fixes: 4647e021193d ("net: stmmac: selftests: Add selftest for L3/L4 Filters") Signed-off-by: Jose Abreu <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Jakub Kicinski [Fri, 10 Jan 2020 12:38:32 +0000 (04:38 -0800)]
net/tls: fix async operation
Mallesham reports the TLS with async accelerator was broken by
commit d10523d0b3d7 ("net/tls: free the record on encryption error")
because encryption can return -EINPROGRESS in such setups, which
should not be treated as an error.
The error is also present in the BPF path (likely copied from there).
Reported-by: Mallesham Jatharakonda <[email protected]> Fixes: d3b18ad31f93 ("tls: add bpf support to sk_msg handling") Fixes: d10523d0b3d7 ("net/tls: free the record on encryption error") Signed-off-by: Jakub Kicinski <[email protected]> Reviewed-by: Simon Horman <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Jakub Kicinski [Fri, 10 Jan 2020 12:36:55 +0000 (04:36 -0800)]
net/tls: avoid spurious decryption error with HW resync
When device loses sync mid way through a record - kernel
has to re-encrypt the part of the record which the device
already decrypted to be able to decrypt and authenticate
the record in its entirety.
The re-encryption piggy backs on the decryption routine,
but obviously because the partially decrypted record can't
be authenticated crypto API returns an error which is then
ignored by tls_device_reencrypt().
Commit 5c5ec6685806 ("net/tls: add TlsDecryptError stat")
added a statistic to count decryption errors, this statistic
can't be incremented when we see the expected re-encryption
error. Move the inc to the caller.
Lorenz Bauer [Fri, 10 Jan 2020 13:23:36 +0000 (13:23 +0000)]
net: bpf: Don't leak time wait and request sockets
It's possible to leak time wait and request sockets via the following
BPF pseudo code:
sk = bpf_skc_lookup_tcp(...)
if (sk)
bpf_sk_release(sk)
If sk->sk_state is TCP_NEW_SYN_RECV or TCP_TIME_WAIT the refcount taken
by bpf_skc_lookup_tcp is not undone by bpf_sk_release. This is because
sk_flags is re-used for other data in both kinds of sockets. The check
!sock_flag(sk, SOCK_RCU_FREE)
therefore returns a bogus result. Check that sk_flags is valid by calling
sk_fullsock. Skip checking SOCK_RCU_FREE if we already know that sk is
not a full socket.
Matthew Garrett [Fri, 3 Jan 2020 11:39:50 +0000 (12:39 +0100)]
efi: Allow disabling PCI busmastering on bridges during boot
Add an option to disable the busmaster bit in the control register on
all PCI bridges before calling ExitBootServices() and passing control
to the runtime kernel. System firmware may configure the IOMMU to prevent
malicious PCI devices from being able to attack the OS via DMA. However,
since firmware can't guarantee that the OS is IOMMU-aware, it will tear
down IOMMU configuration when ExitBootServices() is called. This leaves
a window between where a hostile device could still cause damage before
Linux configures the IOMMU again.
If CONFIG_EFI_DISABLE_PCI_DMA is enabled or "efi=disable_early_pci_dma"
is passed on the command line, the EFI stub will clear the busmaster bit
on all PCI bridges before ExitBootServices() is called. This will
prevent any malicious PCI devices from being able to perform DMA until
the kernel reenables busmastering after configuring the IOMMU.
This option may cause failures with some poorly behaved hardware and
should not be enabled without testing. The kernel commandline options
"efi=disable_early_pci_dma" or "efi=no_disable_early_pci_dma" may be
used to override the default. Note that PCI devices downstream from PCI
bridges are disconnected from their drivers first, using the UEFI
driver model API, so that DMA can be disabled safely at the bridge
level.
[ardb: disconnect PCI I/O handles first, as suggested by Arvind]
Arvind Sankar [Fri, 3 Jan 2020 11:39:49 +0000 (12:39 +0100)]
efi/x86: Allow translating 64-bit arguments for mixed mode calls
Introduce the ability to define macros to perform argument translation
for the calls that need it, and define them for the boot services that
we currently use.
When calling 32-bit firmware methods in mixed mode, all output
parameters that are 32-bit according to the firmware, but 64-bit in the
kernel (ie OUT UINTN * or OUT VOID **) must be initialized in the
kernel, or the upper 32 bits may contain garbage. Define macros that
zero out the upper 32 bits of the output before invoking the firmware
method.
When a 32-bit EFI call takes 64-bit arguments, the mixed-mode call must
push the two 32-bit halves as separate arguments onto the stack. This
can be achieved by splitting the argument into its two halves when
calling the assembler thunk. Define a macro to do this for the
free_pages boot service.
Arvind Sankar [Fri, 3 Jan 2020 11:39:48 +0000 (12:39 +0100)]
efi/x86: Check number of arguments to variadic functions
On x86 we need to thunk through assembler stubs to call the EFI services
for mixed mode, and for runtime services in 64-bit mode. The assembler
stubs have limits on how many arguments it handles. Introduce a few
macros to check that we do not try to pass too many arguments to the
stubs.
Ard Biesheuvel [Fri, 3 Jan 2020 11:39:46 +0000 (12:39 +0100)]
efi/x86: Don't panic or BUG() on non-critical error conditions
The logic in __efi_enter_virtual_mode() does a number of steps in
sequence, all of which may fail in one way or the other. In most
cases, we simply print an error and disable EFI runtime services
support, but in some cases, we BUG() or panic() and bring down the
system when encountering conditions that we could easily handle in
the same way.
While at it, replace a pointless page-to-virt-phys conversion with
one that goes straight from struct page to physical.
Ard Biesheuvel [Fri, 3 Jan 2020 11:39:45 +0000 (12:39 +0100)]
efi/x86: Clean up efi_systab_init() routine for legibility
Clean up the efi_systab_init() routine which maps the EFI system
table and copies the relevant pieces of data out of it.
The current routine is very difficult to read, so let's clean that
up. Also, switch to a R/O mapping of the system table since that is
all we need.
Finally, use a plain u64 variable to record the physical address of
the system table instead of pointlessly stashing it in a struct efi
that is never used for anything else.
Ard Biesheuvel [Fri, 3 Jan 2020 11:39:44 +0000 (12:39 +0100)]
efi/x86: Drop two near identical versions of efi_runtime_init()
The routines efi_runtime_init32() and efi_runtime_init64() are
almost indistinguishable, and the only relevant difference is
the offset in the runtime struct from where to obtain the physical
address of the SetVirtualAddressMap() routine.
However, this address is only used once, when installing the virtual
address map that the OS will use to invoke EFI runtime services, and
at the time of the call, we will necessarily be running with a 1:1
mapping, and so there is no need to do the map/unmap dance here to
retrieve the address. In fact, in the preceding changes to these users,
we stopped using the address recorded here entirely.
So let's just get rid of all this code since it no longer serves a
purpose. While at it, tweak the logic so that we handle unsupported
and disable EFI runtime services in the same way, and unmap the EFI
memory map in both cases.
Ard Biesheuvel [Fri, 3 Jan 2020 11:39:43 +0000 (12:39 +0100)]
efi/x86: Simplify mixed mode call wrapper
Calling 32-bit EFI runtime services from a 64-bit OS involves
switching back to the flat mapping with a stack carved out of
memory that is 32-bit addressable.
There is no need to actually execute the 64-bit part of this
routine from the flat mapping as well, as long as the entry
and return address fit in 32 bits. There is also no need to
preserve part of the calling context in global variables: we
can simply push the old stack pointer value to the new stack,
and keep the return address from the code32 section in EBX.
While at it, move the conditional check whether to invoke
the mixed mode version of SetVirtualAddressMap() into the
64-bit implementation of the wrapper routine.
The efi_call() wrapper used to invoke EFI runtime services serves
a number of purposes:
- realign the stack to 16 bytes
- preserve FP and CR0 register state
- translate from SysV to MS calling convention.
Preserving CR0.TS is no longer necessary in Linux, and preserving the
FP register state is also redundant in most cases, since efi_call() is
almost always used from within the scope of a pair of kernel_fpu_begin()/
kernel_fpu_end() calls, with the exception of the early call to
SetVirtualAddressMap() and the SGI UV support code.
So let's add a pair of kernel_fpu_begin()/_end() calls there as well,
and remove the unnecessary code from the assembly implementation of
efi_call(), and only keep the pieces that deal with the stack
alignment and the ABI translation.
The variadic efi_call_phys() wrapper that exists on i386 was
originally created to call into any EFI firmware runtime service,
but in practice, we only use it once, to call SetVirtualAddressMap()
during early boot.
The flexibility provided by the variadic nature also makes it
type unsafe, and makes the assembler code more complicated than
needed, since it has to deal with an unknown number of arguments
living on the stack.
So clean this up, by renaming the helper to efi_call_svam(), and
dropping the unneeded complexity. Let's also drop the reference
to the efi_phys struct and grab the address from the EFI system
table directly.
Ard Biesheuvel [Fri, 3 Jan 2020 11:39:40 +0000 (12:39 +0100)]
efi/x86: Split SetVirtualAddresMap() wrappers into 32 and 64 bit versions
Split the phys_efi_set_virtual_address_map() routine into 32 and 64 bit
versions, so we can simplify them individually in subsequent patches.
There is very little overlap between the logic anyway, and this has
already been factored out in prolog/epilog routines which are completely
different between 32 bit and 64 bit. So let's take it one step further,
and get rid of the overlap completely.
Ard Biesheuvel [Fri, 3 Jan 2020 11:39:39 +0000 (12:39 +0100)]
efi/x86: Split off some old memmap handling into separate routines
In a subsequent patch, we will fold the prolog/epilog routines that are
part of the support code to call SetVirtualAddressMap() with a 1:1
mapping into the callers. However, the 64-bit version mostly consists
of ugly mapping code that is only used when efi=old_map is in effect,
which is extremely rare. So let's move this code out of the way so it
does not clutter the common code.
Ard Biesheuvel [Fri, 3 Jan 2020 11:39:38 +0000 (12:39 +0100)]
efi/x86: Avoid redundant cast of EFI firmware service pointer
All EFI firmware call prototypes have been annotated as __efiapi,
permitting us to attach attributes regarding the calling convention
by overriding __efiapi to an architecture specific value.
On 32-bit x86, EFI firmware calls use the plain calling convention
where all arguments are passed via the stack, and cleaned up by the
caller. Let's add this to the __efiapi definition so we no longer
need to cast the function pointers before invoking them.
Ard Biesheuvel [Fri, 3 Jan 2020 11:39:37 +0000 (12:39 +0100)]
efi/x86: Map the entire EFI vendor string before copying it
Fix a couple of issues with the way we map and copy the vendor string:
- we map only 2 bytes, which usually works since you get at least a
page, but if the vendor string happens to cross a page boundary,
a crash will result
- only call early_memunmap() if early_memremap() succeeded, or we will
call it with a NULL address which it doesn't like,
- while at it, switch to early_memremap_ro(), and array indexing rather
than pointer dereferencing to read the CHAR16 characters.
Ard Biesheuvel [Fri, 3 Jan 2020 11:39:36 +0000 (12:39 +0100)]
efi/x86: Re-disable RT services for 32-bit kernels running on 64-bit EFI
Commit a8147dba75b1 ("efi/x86: Rename efi_is_native() to efi_is_mixed()")
renamed and refactored efi_is_native() into efi_is_mixed(), but failed
to take into account that these are not diametrical opposites.
Mixed mode is a construct that permits 64-bit kernels to boot on 32-bit
firmware, but there is another non-native combination which is supported,
i.e., 32-bit kernels booting on 64-bit firmware, but only for boot and not
for runtime services. Also, mixed mode can be disabled in Kconfig, in
which case the 64-bit kernel can still be booted from 32-bit firmware,
but without access to runtime services.
Due to this oversight, efi_runtime_supported() now incorrectly returns
true for such configurations, resulting in crashes at boot. So fix this
by making efi_runtime_supported() aware of this.
As a side effect, some efi_thunk_xxx() stubs have become obsolete, so
remove them as well.
Ard Biesheuvel [Fri, 3 Jan 2020 11:39:35 +0000 (12:39 +0100)]
efi/libstub/x86: Force 'hidden' visibility for extern declarations
Commit c3710de5065d ("efi/libstub/x86: Drop __efi_early() export and
efi_config struct") introduced a reference from C code in eboot.c to
the startup_32 symbol defined in the .S startup code. This results in
a GOT based reference to startup_32, and since GOT entries carry
absolute addresses, they need to be fixed up before they can be used.
On modern toolchains (binutils 2.26 or later), this reference is
relaxed into a R_386_GOTOFF relocation (or the analogous X86_64 one)
which never uses the absolute address in the entry, and so we get
away with not fixing up the GOT table before calling the EFI entry
point. However, GCC 4.6 combined with a binutils of the era (2.24)
will produce a true GOT indirected reference, resulting in a wrong
value to be returned for the address of startup_32() if the boot
code is not running at the address it was linked at.
Fortunately, we can easily override this behavior, and force GCC to
emit the GOTOFF relocations explicitly, by setting the visibility
pragma 'hidden'.
Ard Biesheuvel [Fri, 3 Jan 2020 11:39:34 +0000 (12:39 +0100)]
efi/libstub: Fix boot argument handling in mixed mode entry code
The mixed mode refactor actually broke mixed mode by failing to
pass the bootparam structure to startup_32(). This went unnoticed
because it apparently has a high tolerance for being passed random
junk, and still boots fine in some cases. So let's fix this by
populating %esi as required when entering via efi32_stub_entry,
and while at it, preserve the arguments themselves instead of their
address in memory (via the stack pointer) since that memory could
be clobbered before we get to it.
projects / linux.git / log