drivers/mmc/host/sdhci-esdhc-imx.c

   1 // SPDX-License-Identifier: GPL-2.0
   2 /*
   3  * Freescale eSDHC i.MX controller driver for the platform bus.
   4  *
   5  * derived from the OF-version.
   6  *
   7  * Copyright (c) 2010 Pengutronix e.K.
   8  *   Author: Wolfram Sang <[email protected]>
   9  */
  10
  11 #include <linux/bitfield.h>
  12 #include <linux/io.h>
  13 #include <linux/iopoll.h>
  14 #include <linux/delay.h>
  15 #include <linux/err.h>
  16 #include <linux/clk.h>
  17 #include <linux/module.h>
  18 #include <linux/slab.h>
  19 #include <linux/pm_qos.h>
  20 #include <linux/mmc/host.h>
  21 #include <linux/mmc/mmc.h>
  22 #include <linux/mmc/sdio.h>
  23 #include <linux/mmc/slot-gpio.h>
  24 #include <linux/of.h>
  25 #include <linux/of_device.h>
  26 #include <linux/pinctrl/consumer.h>
  27 #include <linux/pm_runtime.h>
  28 #include "sdhci-cqhci.h"
  29 #include "sdhci-pltfm.h"
  30 #include "sdhci-esdhc.h"
  31 #include "cqhci.h"
  32
  33 #define ESDHC_SYS_CTRL_DTOCV_MASK       0x0f
  34 #define ESDHC_CTRL_D3CD                 0x08
  35 #define ESDHC_BURST_LEN_EN_INCR         (1 << 27)
  36 /* VENDOR SPEC register */
  37 #define ESDHC_VENDOR_SPEC               0xc0
  38 #define  ESDHC_VENDOR_SPEC_SDIO_QUIRK   (1 << 1)
  39 #define  ESDHC_VENDOR_SPEC_VSELECT      (1 << 1)
  40 #define  ESDHC_VENDOR_SPEC_FRC_SDCLK_ON (1 << 8)
  41 #define ESDHC_DEBUG_SEL_AND_STATUS_REG          0xc2
  42 #define ESDHC_DEBUG_SEL_REG                     0xc3
  43 #define ESDHC_DEBUG_SEL_MASK                    0xf
  44 #define ESDHC_DEBUG_SEL_CMD_STATE               1
  45 #define ESDHC_DEBUG_SEL_DATA_STATE              2
  46 #define ESDHC_DEBUG_SEL_TRANS_STATE             3
  47 #define ESDHC_DEBUG_SEL_DMA_STATE               4
  48 #define ESDHC_DEBUG_SEL_ADMA_STATE              5
  49 #define ESDHC_DEBUG_SEL_FIFO_STATE              6
  50 #define ESDHC_DEBUG_SEL_ASYNC_FIFO_STATE        7
  51 #define ESDHC_WTMK_LVL                  0x44
  52 #define  ESDHC_WTMK_DEFAULT_VAL         0x10401040
  53 #define  ESDHC_WTMK_LVL_RD_WML_MASK     0x000000FF
  54 #define  ESDHC_WTMK_LVL_RD_WML_SHIFT    0
  55 #define  ESDHC_WTMK_LVL_WR_WML_MASK     0x00FF0000
  56 #define  ESDHC_WTMK_LVL_WR_WML_SHIFT    16
  57 #define  ESDHC_WTMK_LVL_WML_VAL_DEF     64
  58 #define  ESDHC_WTMK_LVL_WML_VAL_MAX     128
  59 #define ESDHC_MIX_CTRL                  0x48
  60 #define  ESDHC_MIX_CTRL_DDREN           (1 << 3)
  61 #define  ESDHC_MIX_CTRL_AC23EN          (1 << 7)
  62 #define  ESDHC_MIX_CTRL_EXE_TUNE        (1 << 22)
  63 #define  ESDHC_MIX_CTRL_SMPCLK_SEL      (1 << 23)
  64 #define  ESDHC_MIX_CTRL_AUTO_TUNE_EN    (1 << 24)
  65 #define  ESDHC_MIX_CTRL_FBCLK_SEL       (1 << 25)
  66 #define  ESDHC_MIX_CTRL_HS400_EN        (1 << 26)
  67 #define  ESDHC_MIX_CTRL_HS400_ES_EN     (1 << 27)
  68 /* Bits 3 and 6 are not SDHCI standard definitions */
  69 #define  ESDHC_MIX_CTRL_SDHCI_MASK      0xb7
  70 /* Tuning bits */
  71 #define  ESDHC_MIX_CTRL_TUNING_MASK     0x03c00000
  72
  73 /* dll control register */
  74 #define ESDHC_DLL_CTRL                  0x60
  75 #define ESDHC_DLL_OVERRIDE_VAL_SHIFT    9
  76 #define ESDHC_DLL_OVERRIDE_EN_SHIFT     8
  77
  78 /* tune control register */
  79 #define ESDHC_TUNE_CTRL_STATUS          0x68
  80 #define  ESDHC_TUNE_CTRL_STEP           1
  81 #define  ESDHC_TUNE_CTRL_MIN            0
  82 #define  ESDHC_TUNE_CTRL_MAX            ((1 << 7) - 1)
  83
  84 /* strobe dll register */
  85 #define ESDHC_STROBE_DLL_CTRL           0x70
  86 #define ESDHC_STROBE_DLL_CTRL_ENABLE    (1 << 0)
  87 #define ESDHC_STROBE_DLL_CTRL_RESET     (1 << 1)
  88 #define ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_DEFAULT    0x7
  89 #define ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_SHIFT      3
  90 #define ESDHC_STROBE_DLL_CTRL_SLV_UPDATE_INT_DEFAULT    (4 << 20)
  91
  92 #define ESDHC_STROBE_DLL_STATUS         0x74
  93 #define ESDHC_STROBE_DLL_STS_REF_LOCK   (1 << 1)
  94 #define ESDHC_STROBE_DLL_STS_SLV_LOCK   0x1
  95
  96 #define ESDHC_VEND_SPEC2                0xc8
  97 #define ESDHC_VEND_SPEC2_EN_BUSY_IRQ    (1 << 8)
  98 #define ESDHC_VEND_SPEC2_AUTO_TUNE_8BIT_EN      (1 << 4)
  99 #define ESDHC_VEND_SPEC2_AUTO_TUNE_4BIT_EN      (0 << 4)
 100 #define ESDHC_VEND_SPEC2_AUTO_TUNE_1BIT_EN      (2 << 4)
 101 #define ESDHC_VEND_SPEC2_AUTO_TUNE_CMD_EN       (1 << 6)
 102 #define ESDHC_VEND_SPEC2_AUTO_TUNE_MODE_MASK    (7 << 4)
 103
 104 #define ESDHC_TUNING_CTRL               0xcc
 105 #define ESDHC_STD_TUNING_EN             (1 << 24)
 106 /* NOTE: the minimum valid tuning start tap for mx6sl is 1 */
 107 #define ESDHC_TUNING_START_TAP_DEFAULT  0x1
 108 #define ESDHC_TUNING_START_TAP_MASK     0x7f
 109 #define ESDHC_TUNING_CMD_CRC_CHECK_DISABLE      (1 << 7)
 110 #define ESDHC_TUNING_STEP_DEFAULT       0x1
 111 #define ESDHC_TUNING_STEP_MASK          0x00070000
 112 #define ESDHC_TUNING_STEP_SHIFT         16
 113
 114 /* pinctrl state */
 115 #define ESDHC_PINCTRL_STATE_100MHZ      "state_100mhz"
 116 #define ESDHC_PINCTRL_STATE_200MHZ      "state_200mhz"
 117
 118 /*
 119  * Our interpretation of the SDHCI_HOST_CONTROL register
 120  */
 121 #define ESDHC_CTRL_4BITBUS              (0x1 << 1)
 122 #define ESDHC_CTRL_8BITBUS              (0x2 << 1)
 123 #define ESDHC_CTRL_BUSWIDTH_MASK        (0x3 << 1)
 124 #define USDHC_GET_BUSWIDTH(c) (c & ESDHC_CTRL_BUSWIDTH_MASK)
 125
 126 /*
 127  * There is an INT DMA ERR mismatch between eSDHC and STD SDHC SPEC:
 128  * Bit25 is used in STD SPEC, and is reserved in fsl eSDHC design,
 129  * but bit28 is used as the INT DMA ERR in fsl eSDHC design.
 130  * Define this macro DMA error INT for fsl eSDHC
 131  */
 132 #define ESDHC_INT_VENDOR_SPEC_DMA_ERR   (1 << 28)
 133
 134 /* the address offset of CQHCI */
 135 #define ESDHC_CQHCI_ADDR_OFFSET         0x100
 136
 137 /*
 138  * The CMDTYPE of the CMD register (offset 0xE) should be set to
 139  * "11" when the STOP CMD12 is issued on imx53 to abort one
 140  * open ended multi-blk IO. Otherwise the TC INT wouldn't
 141  * be generated.
 142  * In exact block transfer, the controller doesn't complete the
 143  * operations automatically as required at the end of the
 144  * transfer and remains on hold if the abort command is not sent.
 145  * As a result, the TC flag is not asserted and SW received timeout
 146  * exception. Bit1 of Vendor Spec register is used to fix it.
 147  */
 148 #define ESDHC_FLAG_MULTIBLK_NO_INT      BIT(1)
 149 /*
 150  * The flag tells that the ESDHC controller is an USDHC block that is
 151  * integrated on the i.MX6 series.
 152  */
 153 #define ESDHC_FLAG_USDHC                BIT(3)
 154 /* The IP supports manual tuning process */
 155 #define ESDHC_FLAG_MAN_TUNING           BIT(4)
 156 /* The IP supports standard tuning process */
 157 #define ESDHC_FLAG_STD_TUNING           BIT(5)
 158 /* The IP has SDHCI_CAPABILITIES_1 register */
 159 #define ESDHC_FLAG_HAVE_CAP1            BIT(6)
 160 /*
 161  * The IP has erratum ERR004536
 162  * uSDHC: ADMA Length Mismatch Error occurs if the AHB read access is slow,
 163  * when reading data from the card
 164  * This flag is also set for i.MX25 and i.MX35 in order to get
 165  * SDHCI_QUIRK_BROKEN_ADMA, but for different reasons (ADMA capability bits).
 166  */
 167 #define ESDHC_FLAG_ERR004536            BIT(7)
 168 /* The IP supports HS200 mode */
 169 #define ESDHC_FLAG_HS200                BIT(8)
 170 /* The IP supports HS400 mode */
 171 #define ESDHC_FLAG_HS400                BIT(9)
 172 /*
 173  * The IP has errata ERR010450
 174  * uSDHC: Due to the I/O timing limit, for SDR mode, SD card clock can't
 175  * exceed 150MHz, for DDR mode, SD card clock can't exceed 45MHz.
 176  */
 177 #define ESDHC_FLAG_ERR010450            BIT(10)
 178 /* The IP supports HS400ES mode */
 179 #define ESDHC_FLAG_HS400_ES             BIT(11)
 180 /* The IP has Host Controller Interface for Command Queuing */
 181 #define ESDHC_FLAG_CQHCI                BIT(12)
 182 /* need request pmqos during low power */
 183 #define ESDHC_FLAG_PMQOS                BIT(13)
 184 /* The IP state got lost in low power mode */
 185 #define ESDHC_FLAG_STATE_LOST_IN_LPMODE         BIT(14)
 186 /* The IP lost clock rate in PM_RUNTIME */
 187 #define ESDHC_FLAG_CLK_RATE_LOST_IN_PM_RUNTIME  BIT(15)
 188 /*
 189  * The IP do not support the ACMD23 feature completely when use ADMA mode.
 190  * In ADMA mode, it only use the 16 bit block count of the register 0x4
 191  * (BLOCK_ATT) as the CMD23's argument for ACMD23 mode, which means it will
 192  * ignore the upper 16 bit of the CMD23's argument. This will block the reliable
 193  * write operation in RPMB, because RPMB reliable write need to set the bit31
 194  * of the CMD23's argument.
 195  * imx6qpdl/imx6sx/imx6sl/imx7d has this limitation only for ADMA mode, SDMA
 196  * do not has this limitation. so when these SoC use ADMA mode, it need to
 197  * disable the ACMD23 feature.
 198  */
 199 #define ESDHC_FLAG_BROKEN_AUTO_CMD23    BIT(16)
 200
 201 /* ERR004536 is not applicable for the IP  */
 202 #define ESDHC_FLAG_SKIP_ERR004536       BIT(17)
 203
 204 enum wp_types {
 205         ESDHC_WP_NONE,          /* no WP, neither controller nor gpio */
 206         ESDHC_WP_CONTROLLER,    /* mmc controller internal WP */
 207         ESDHC_WP_GPIO,          /* external gpio pin for WP */
 208 };
 209
 210 enum cd_types {
 211         ESDHC_CD_NONE,          /* no CD, neither controller nor gpio */
 212         ESDHC_CD_CONTROLLER,    /* mmc controller internal CD */
 213         ESDHC_CD_GPIO,          /* external gpio pin for CD */
 214         ESDHC_CD_PERMANENT,     /* no CD, card permanently wired to host */
 215 };
 216
 217 /*
 218  * struct esdhc_platform_data - platform data for esdhc on i.MX
 219  *
 220  * ESDHC_WP(CD)_CONTROLLER type is not available on i.MX25/35.
 221  *
 222  * @wp_type:    type of write_protect method (see wp_types enum above)
 223  * @cd_type:    type of card_detect method (see cd_types enum above)
 224  */
 225
 226 struct esdhc_platform_data {
 227         enum wp_types wp_type;
 228         enum cd_types cd_type;
 229         int max_bus_width;
 230         unsigned int delay_line;
 231         unsigned int tuning_step;       /* The delay cell steps in tuning procedure */
 232         unsigned int tuning_start_tap;  /* The start delay cell point in tuning procedure */
 233         unsigned int strobe_dll_delay_target;   /* The delay cell for strobe pad (read clock) */
 234 };
 235
 236 struct esdhc_soc_data {
 237         u32 flags;
 238 };
 239
 240 static const struct esdhc_soc_data esdhc_imx25_data = {
 241         .flags = ESDHC_FLAG_ERR004536,
 242 };
 243
 244 static const struct esdhc_soc_data esdhc_imx35_data = {
 245         .flags = ESDHC_FLAG_ERR004536,
 246 };
 247
 248 static const struct esdhc_soc_data esdhc_imx51_data = {
 249         .flags = 0,
 250 };
 251
 252 static const struct esdhc_soc_data esdhc_imx53_data = {
 253         .flags = ESDHC_FLAG_MULTIBLK_NO_INT,
 254 };
 255
 256 static const struct esdhc_soc_data usdhc_imx6q_data = {
 257         .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_MAN_TUNING
 258                         | ESDHC_FLAG_BROKEN_AUTO_CMD23,
 259 };
 260
 261 static const struct esdhc_soc_data usdhc_imx6sl_data = {
 262         .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
 263                         | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_ERR004536
 264                         | ESDHC_FLAG_HS200
 265                         | ESDHC_FLAG_BROKEN_AUTO_CMD23,
 266 };
 267
 268 static const struct esdhc_soc_data usdhc_imx6sll_data = {
 269         .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
 270                         | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
 271                         | ESDHC_FLAG_HS400
 272                         | ESDHC_FLAG_STATE_LOST_IN_LPMODE,
 273 };
 274
 275 static const struct esdhc_soc_data usdhc_imx6sx_data = {
 276         .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
 277                         | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
 278                         | ESDHC_FLAG_STATE_LOST_IN_LPMODE
 279                         | ESDHC_FLAG_BROKEN_AUTO_CMD23,
 280 };
 281
 282 static const struct esdhc_soc_data usdhc_imx6ull_data = {
 283         .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
 284                         | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
 285                         | ESDHC_FLAG_ERR010450
 286                         | ESDHC_FLAG_STATE_LOST_IN_LPMODE,
 287 };
 288
 289 static const struct esdhc_soc_data usdhc_imx7d_data = {
 290         .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
 291                         | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
 292                         | ESDHC_FLAG_HS400
 293                         | ESDHC_FLAG_STATE_LOST_IN_LPMODE
 294                         | ESDHC_FLAG_BROKEN_AUTO_CMD23,
 295 };
 296
 297 static struct esdhc_soc_data usdhc_s32g2_data = {
 298         .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_MAN_TUNING
 299                         | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
 300                         | ESDHC_FLAG_HS400 | ESDHC_FLAG_HS400_ES
 301                         | ESDHC_FLAG_SKIP_ERR004536,
 302 };
 303
 304 static struct esdhc_soc_data usdhc_imx7ulp_data = {
 305         .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
 306                         | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
 307                         | ESDHC_FLAG_PMQOS | ESDHC_FLAG_HS400
 308                         | ESDHC_FLAG_STATE_LOST_IN_LPMODE,
 309 };
 310 static struct esdhc_soc_data usdhc_imxrt1050_data = {
 311         .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
 312                         | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200,
 313 };
 314
 315 static struct esdhc_soc_data usdhc_imx8qxp_data = {
 316         .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
 317                         | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
 318                         | ESDHC_FLAG_HS400 | ESDHC_FLAG_HS400_ES
 319                         | ESDHC_FLAG_STATE_LOST_IN_LPMODE
 320                         | ESDHC_FLAG_CLK_RATE_LOST_IN_PM_RUNTIME,
 321 };
 322
 323 static struct esdhc_soc_data usdhc_imx8mm_data = {
 324         .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
 325                         | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
 326                         | ESDHC_FLAG_HS400 | ESDHC_FLAG_HS400_ES
 327                         | ESDHC_FLAG_STATE_LOST_IN_LPMODE,
 328 };
 329
 330 struct pltfm_imx_data {
 331         u32 scratchpad;
 332         struct pinctrl *pinctrl;
 333         struct pinctrl_state *pins_100mhz;
 334         struct pinctrl_state *pins_200mhz;
 335         const struct esdhc_soc_data *socdata;
 336         struct esdhc_platform_data boarddata;
 337         struct clk *clk_ipg;
 338         struct clk *clk_ahb;
 339         struct clk *clk_per;
 340         unsigned int actual_clock;
 341
 342         /*
 343          * USDHC has one limition, require the SDIO device a different
 344          * register setting. Driver has to recognize card type during
 345          * the card init, but at this stage, mmc_host->card is not
 346          * available. So involve this field to save the card type
 347          * during card init through usdhc_init_card().
 348          */
 349         unsigned int init_card_type;
 350
 351         enum {
 352                 NO_CMD_PENDING,      /* no multiblock command pending */
 353                 MULTIBLK_IN_PROCESS, /* exact multiblock cmd in process */
 354                 WAIT_FOR_INT,        /* sent CMD12, waiting for response INT */
 355         } multiblock_status;
 356         u32 is_ddr;
 357         struct pm_qos_request pm_qos_req;
 358 };
 359
 360 static const struct of_device_id imx_esdhc_dt_ids[] = {
 361         { .compatible = "fsl,imx25-esdhc", .data = &esdhc_imx25_data, },
 362         { .compatible = "fsl,imx35-esdhc", .data = &esdhc_imx35_data, },
 363         { .compatible = "fsl,imx51-esdhc", .data = &esdhc_imx51_data, },
 364         { .compatible = "fsl,imx53-esdhc", .data = &esdhc_imx53_data, },
 365         { .compatible = "fsl,imx6sx-usdhc", .data = &usdhc_imx6sx_data, },
 366         { .compatible = "fsl,imx6sl-usdhc", .data = &usdhc_imx6sl_data, },
 367         { .compatible = "fsl,imx6sll-usdhc", .data = &usdhc_imx6sll_data, },
 368         { .compatible = "fsl,imx6q-usdhc", .data = &usdhc_imx6q_data, },
 369         { .compatible = "fsl,imx6ull-usdhc", .data = &usdhc_imx6ull_data, },
 370         { .compatible = "fsl,imx7d-usdhc", .data = &usdhc_imx7d_data, },
 371         { .compatible = "fsl,imx7ulp-usdhc", .data = &usdhc_imx7ulp_data, },
 372         { .compatible = "fsl,imx8qxp-usdhc", .data = &usdhc_imx8qxp_data, },
 373         { .compatible = "fsl,imx8mm-usdhc", .data = &usdhc_imx8mm_data, },
 374         { .compatible = "fsl,imxrt1050-usdhc", .data = &usdhc_imxrt1050_data, },
 375         { .compatible = "nxp,s32g2-usdhc", .data = &usdhc_s32g2_data, },
 376         { /* sentinel */ }
 377 };
 378 MODULE_DEVICE_TABLE(of, imx_esdhc_dt_ids);
 379
 380 static inline int is_imx25_esdhc(struct pltfm_imx_data *data)
 381 {
 382         return data->socdata == &esdhc_imx25_data;
 383 }
 384
 385 static inline int is_imx53_esdhc(struct pltfm_imx_data *data)
 386 {
 387         return data->socdata == &esdhc_imx53_data;
 388 }
 389
 390 static inline int esdhc_is_usdhc(struct pltfm_imx_data *data)
 391 {
 392         return !!(data->socdata->flags & ESDHC_FLAG_USDHC);
 393 }
 394
 395 static inline void esdhc_clrset_le(struct sdhci_host *host, u32 mask, u32 val, int reg)
 396 {
 397         void __iomem *base = host->ioaddr + (reg & ~0x3);
 398         u32 shift = (reg & 0x3) * 8;
 399
 400         writel(((readl(base) & ~(mask << shift)) | (val << shift)), base);
 401 }
 402
 403 #define DRIVER_NAME "sdhci-esdhc-imx"
 404 #define ESDHC_IMX_DUMP(f, x...) \
 405         pr_err("%s: " DRIVER_NAME ": " f, mmc_hostname(host->mmc), ## x)
 406 static void esdhc_dump_debug_regs(struct sdhci_host *host)
 407 {
 408         int i;
 409         char *debug_status[7] = {
 410                                  "cmd debug status",
 411                                  "data debug status",
 412                                  "trans debug status",
 413                                  "dma debug status",
 414                                  "adma debug status",
 415                                  "fifo debug status",
 416                                  "async fifo debug status"
 417         };
 418
 419         ESDHC_IMX_DUMP("========= ESDHC IMX DEBUG STATUS DUMP =========\n");
 420         for (i = 0; i < 7; i++) {
 421                 esdhc_clrset_le(host, ESDHC_DEBUG_SEL_MASK,
 422                         ESDHC_DEBUG_SEL_CMD_STATE + i, ESDHC_DEBUG_SEL_REG);
 423                 ESDHC_IMX_DUMP("%s:  0x%04x\n", debug_status[i],
 424                         readw(host->ioaddr + ESDHC_DEBUG_SEL_AND_STATUS_REG));
 425         }
 426
 427         esdhc_clrset_le(host, ESDHC_DEBUG_SEL_MASK, 0, ESDHC_DEBUG_SEL_REG);
 428
 429 }
 430
 431 static inline void esdhc_wait_for_card_clock_gate_off(struct sdhci_host *host)
 432 {
 433         u32 present_state;
 434         int ret;
 435
 436         ret = readl_poll_timeout(host->ioaddr + ESDHC_PRSSTAT, present_state,
 437                                 (present_state & ESDHC_CLOCK_GATE_OFF), 2, 100);
 438         if (ret == -ETIMEDOUT)
 439                 dev_warn(mmc_dev(host->mmc), "%s: card clock still not gate off in 100us!.\n", __func__);
 440 }
 441
 442 /* Enable the auto tuning circuit to check the CMD line and BUS line */
 443 static inline void usdhc_auto_tuning_mode_sel_and_en(struct sdhci_host *host)
 444 {
 445         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 446         struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
 447         u32 buswidth, auto_tune_buswidth;
 448         u32 reg;
 449
 450         buswidth = USDHC_GET_BUSWIDTH(readl(host->ioaddr + SDHCI_HOST_CONTROL));
 451
 452         switch (buswidth) {
 453         case ESDHC_CTRL_8BITBUS:
 454                 auto_tune_buswidth = ESDHC_VEND_SPEC2_AUTO_TUNE_8BIT_EN;
 455                 break;
 456         case ESDHC_CTRL_4BITBUS:
 457                 auto_tune_buswidth = ESDHC_VEND_SPEC2_AUTO_TUNE_4BIT_EN;
 458                 break;
 459         default:        /* 1BITBUS */
 460                 auto_tune_buswidth = ESDHC_VEND_SPEC2_AUTO_TUNE_1BIT_EN;
 461                 break;
 462         }
 463
 464         /*
 465          * For USDHC, auto tuning circuit can not handle the async sdio
 466          * device interrupt correctly. When sdio device use 4 data lines,
 467          * async sdio interrupt will use the shared DAT[1], if enable auto
 468          * tuning circuit check these 4 data lines, include the DAT[1],
 469          * this circuit will detect this interrupt, take this as a data on
 470          * DAT[1], and adjust the delay cell wrongly.
 471          * This is the hardware design limitation, to avoid this, for sdio
 472          * device, config the auto tuning circuit only check DAT[0] and CMD
 473          * line.
 474          */
 475         if (imx_data->init_card_type == MMC_TYPE_SDIO)
 476                 auto_tune_buswidth = ESDHC_VEND_SPEC2_AUTO_TUNE_1BIT_EN;
 477
 478         esdhc_clrset_le(host, ESDHC_VEND_SPEC2_AUTO_TUNE_MODE_MASK,
 479                         auto_tune_buswidth | ESDHC_VEND_SPEC2_AUTO_TUNE_CMD_EN,
 480                         ESDHC_VEND_SPEC2);
 481
 482         reg = readl(host->ioaddr + ESDHC_MIX_CTRL);
 483         reg |= ESDHC_MIX_CTRL_AUTO_TUNE_EN;
 484         writel(reg, host->ioaddr + ESDHC_MIX_CTRL);
 485 }
 486
 487 static u32 esdhc_readl_le(struct sdhci_host *host, int reg)
 488 {
 489         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 490         struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
 491         u32 val = readl(host->ioaddr + reg);
 492
 493         if (unlikely(reg == SDHCI_PRESENT_STATE)) {
 494                 u32 fsl_prss = val;
 495                 /* save the least 20 bits */
 496                 val = fsl_prss & 0x000FFFFF;
 497                 /* move dat[0-3] bits */
 498                 val |= (fsl_prss & 0x0F000000) >> 4;
 499                 /* move cmd line bit */
 500                 val |= (fsl_prss & 0x00800000) << 1;
 501         }
 502
 503         if (unlikely(reg == SDHCI_CAPABILITIES)) {
 504                 /* ignore bit[0-15] as it stores cap_1 register val for mx6sl */
 505                 if (imx_data->socdata->flags & ESDHC_FLAG_HAVE_CAP1)
 506                         val &= 0xffff0000;
 507
 508                 /* In FSL esdhc IC module, only bit20 is used to indicate the
 509                  * ADMA2 capability of esdhc, but this bit is messed up on
 510                  * some SOCs (e.g. on MX25, MX35 this bit is set, but they
 511                  * don't actually support ADMA2). So set the BROKEN_ADMA
 512                  * quirk on MX25/35 platforms.
 513                  */
 514
 515                 if (val & SDHCI_CAN_DO_ADMA1) {
 516                         val &= ~SDHCI_CAN_DO_ADMA1;
 517                         val |= SDHCI_CAN_DO_ADMA2;
 518                 }
 519         }
 520
 521         if (unlikely(reg == SDHCI_CAPABILITIES_1)) {
 522                 if (esdhc_is_usdhc(imx_data)) {
 523                         if (imx_data->socdata->flags & ESDHC_FLAG_HAVE_CAP1)
 524                                 val = readl(host->ioaddr + SDHCI_CAPABILITIES) & 0xFFFF;
 525                         else
 526                                 /* imx6q/dl does not have cap_1 register, fake one */
 527                                 val = SDHCI_SUPPORT_DDR50 | SDHCI_SUPPORT_SDR104
 528                                         | SDHCI_SUPPORT_SDR50
 529                                         | SDHCI_USE_SDR50_TUNING
 530                                         | FIELD_PREP(SDHCI_RETUNING_MODE_MASK,
 531                                                      SDHCI_TUNING_MODE_3);
 532
 533                         /*
 534                          * Do not advertise faster UHS modes if there are no
 535                          * pinctrl states for 100MHz/200MHz.
 536                          */
 537                         if (IS_ERR_OR_NULL(imx_data->pins_100mhz))
 538                                 val &= ~(SDHCI_SUPPORT_SDR50 | SDHCI_SUPPORT_DDR50);
 539                         if (IS_ERR_OR_NULL(imx_data->pins_200mhz))
 540                                 val &= ~(SDHCI_SUPPORT_SDR104 | SDHCI_SUPPORT_HS400);
 541                 }
 542         }
 543
 544         if (unlikely(reg == SDHCI_MAX_CURRENT) && esdhc_is_usdhc(imx_data)) {
 545                 val = 0;
 546                 val |= FIELD_PREP(SDHCI_MAX_CURRENT_330_MASK, 0xFF);
 547                 val |= FIELD_PREP(SDHCI_MAX_CURRENT_300_MASK, 0xFF);
 548                 val |= FIELD_PREP(SDHCI_MAX_CURRENT_180_MASK, 0xFF);
 549         }
 550
 551         if (unlikely(reg == SDHCI_INT_STATUS)) {
 552                 if (val & ESDHC_INT_VENDOR_SPEC_DMA_ERR) {
 553                         val &= ~ESDHC_INT_VENDOR_SPEC_DMA_ERR;
 554                         val |= SDHCI_INT_ADMA_ERROR;
 555                 }
 556
 557                 /*
 558                  * mask off the interrupt we get in response to the manually
 559                  * sent CMD12
 560                  */
 561                 if ((imx_data->multiblock_status == WAIT_FOR_INT) &&
 562                     ((val & SDHCI_INT_RESPONSE) == SDHCI_INT_RESPONSE)) {
 563                         val &= ~SDHCI_INT_RESPONSE;
 564                         writel(SDHCI_INT_RESPONSE, host->ioaddr +
 565                                                    SDHCI_INT_STATUS);
 566                         imx_data->multiblock_status = NO_CMD_PENDING;
 567                 }
 568         }
 569
 570         return val;
 571 }
 572
 573 static void esdhc_writel_le(struct sdhci_host *host, u32 val, int reg)
 574 {
 575         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 576         struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
 577         u32 data;
 578
 579         if (unlikely(reg == SDHCI_INT_ENABLE || reg == SDHCI_SIGNAL_ENABLE ||
 580                         reg == SDHCI_INT_STATUS)) {
 581                 if ((val & SDHCI_INT_CARD_INT) && !esdhc_is_usdhc(imx_data)) {
 582                         /*
 583                          * Clear and then set D3CD bit to avoid missing the
 584                          * card interrupt. This is an eSDHC controller problem
 585                          * so we need to apply the following workaround: clear
 586                          * and set D3CD bit will make eSDHC re-sample the card
 587                          * interrupt. In case a card interrupt was lost,
 588                          * re-sample it by the following steps.
 589                          */
 590                         data = readl(host->ioaddr + SDHCI_HOST_CONTROL);
 591                         data &= ~ESDHC_CTRL_D3CD;
 592                         writel(data, host->ioaddr + SDHCI_HOST_CONTROL);
 593                         data |= ESDHC_CTRL_D3CD;
 594                         writel(data, host->ioaddr + SDHCI_HOST_CONTROL);
 595                 }
 596
 597                 if (val & SDHCI_INT_ADMA_ERROR) {
 598                         val &= ~SDHCI_INT_ADMA_ERROR;
 599                         val |= ESDHC_INT_VENDOR_SPEC_DMA_ERR;
 600                 }
 601         }
 602
 603         if (unlikely((imx_data->socdata->flags & ESDHC_FLAG_MULTIBLK_NO_INT)
 604                                 && (reg == SDHCI_INT_STATUS)
 605                                 && (val & SDHCI_INT_DATA_END))) {
 606                         u32 v;
 607                         v = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
 608                         v &= ~ESDHC_VENDOR_SPEC_SDIO_QUIRK;
 609                         writel(v, host->ioaddr + ESDHC_VENDOR_SPEC);
 610
 611                         if (imx_data->multiblock_status == MULTIBLK_IN_PROCESS)
 612                         {
 613                                 /* send a manual CMD12 with RESPTYP=none */
 614                                 data = MMC_STOP_TRANSMISSION << 24 |
 615                                        SDHCI_CMD_ABORTCMD << 16;
 616                                 writel(data, host->ioaddr + SDHCI_TRANSFER_MODE);
 617                                 imx_data->multiblock_status = WAIT_FOR_INT;
 618                         }
 619         }
 620
 621         writel(val, host->ioaddr + reg);
 622 }
 623
 624 static u16 esdhc_readw_le(struct sdhci_host *host, int reg)
 625 {
 626         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 627         struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
 628         u16 ret = 0;
 629         u32 val;
 630
 631         if (unlikely(reg == SDHCI_HOST_VERSION)) {
 632                 reg ^= 2;
 633                 if (esdhc_is_usdhc(imx_data)) {
 634                         /*
 635                          * The usdhc register returns a wrong host version.
 636                          * Correct it here.
 637                          */
 638                         return SDHCI_SPEC_300;
 639                 }
 640         }
 641
 642         if (unlikely(reg == SDHCI_HOST_CONTROL2)) {
 643                 val = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
 644                 if (val & ESDHC_VENDOR_SPEC_VSELECT)
 645                         ret |= SDHCI_CTRL_VDD_180;
 646
 647                 if (esdhc_is_usdhc(imx_data)) {
 648                         if (imx_data->socdata->flags & ESDHC_FLAG_MAN_TUNING)
 649                                 val = readl(host->ioaddr + ESDHC_MIX_CTRL);
 650                         else if (imx_data->socdata->flags & ESDHC_FLAG_STD_TUNING)
 651                                 /* the std tuning bits is in ACMD12_ERR for imx6sl */
 652                                 val = readl(host->ioaddr + SDHCI_AUTO_CMD_STATUS);
 653                 }
 654
 655                 if (val & ESDHC_MIX_CTRL_EXE_TUNE)
 656                         ret |= SDHCI_CTRL_EXEC_TUNING;
 657                 if (val & ESDHC_MIX_CTRL_SMPCLK_SEL)
 658                         ret |= SDHCI_CTRL_TUNED_CLK;
 659
 660                 ret &= ~SDHCI_CTRL_PRESET_VAL_ENABLE;
 661
 662                 return ret;
 663         }
 664
 665         if (unlikely(reg == SDHCI_TRANSFER_MODE)) {
 666                 if (esdhc_is_usdhc(imx_data)) {
 667                         u32 m = readl(host->ioaddr + ESDHC_MIX_CTRL);
 668                         ret = m & ESDHC_MIX_CTRL_SDHCI_MASK;
 669                         /* Swap AC23 bit */
 670                         if (m & ESDHC_MIX_CTRL_AC23EN) {
 671                                 ret &= ~ESDHC_MIX_CTRL_AC23EN;
 672                                 ret |= SDHCI_TRNS_AUTO_CMD23;
 673                         }
 674                 } else {
 675                         ret = readw(host->ioaddr + SDHCI_TRANSFER_MODE);
 676                 }
 677
 678                 return ret;
 679         }
 680
 681         return readw(host->ioaddr + reg);
 682 }
 683
 684 static void esdhc_writew_le(struct sdhci_host *host, u16 val, int reg)
 685 {
 686         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 687         struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
 688         u32 new_val = 0;
 689
 690         switch (reg) {
 691         case SDHCI_CLOCK_CONTROL:
 692                 new_val = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
 693                 if (val & SDHCI_CLOCK_CARD_EN)
 694                         new_val |= ESDHC_VENDOR_SPEC_FRC_SDCLK_ON;
 695                 else
 696                         new_val &= ~ESDHC_VENDOR_SPEC_FRC_SDCLK_ON;
 697                 writel(new_val, host->ioaddr + ESDHC_VENDOR_SPEC);
 698                 if (!(new_val & ESDHC_VENDOR_SPEC_FRC_SDCLK_ON))
 699                         esdhc_wait_for_card_clock_gate_off(host);
 700                 return;
 701         case SDHCI_HOST_CONTROL2:
 702                 new_val = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
 703                 if (val & SDHCI_CTRL_VDD_180)
 704                         new_val |= ESDHC_VENDOR_SPEC_VSELECT;
 705                 else
 706                         new_val &= ~ESDHC_VENDOR_SPEC_VSELECT;
 707                 writel(new_val, host->ioaddr + ESDHC_VENDOR_SPEC);
 708                 if (imx_data->socdata->flags & ESDHC_FLAG_STD_TUNING) {
 709                         u32 v = readl(host->ioaddr + SDHCI_AUTO_CMD_STATUS);
 710                         u32 m = readl(host->ioaddr + ESDHC_MIX_CTRL);
 711                         if (val & SDHCI_CTRL_TUNED_CLK) {
 712                                 v |= ESDHC_MIX_CTRL_SMPCLK_SEL;
 713                         } else {
 714                                 v &= ~ESDHC_MIX_CTRL_SMPCLK_SEL;
 715                                 m &= ~ESDHC_MIX_CTRL_FBCLK_SEL;
 716                         }
 717
 718                         if (val & SDHCI_CTRL_EXEC_TUNING) {
 719                                 v |= ESDHC_MIX_CTRL_EXE_TUNE;
 720                                 m |= ESDHC_MIX_CTRL_FBCLK_SEL;
 721                         } else {
 722                                 v &= ~ESDHC_MIX_CTRL_EXE_TUNE;
 723                         }
 724
 725                         writel(v, host->ioaddr + SDHCI_AUTO_CMD_STATUS);
 726                         writel(m, host->ioaddr + ESDHC_MIX_CTRL);
 727                 }
 728                 return;
 729         case SDHCI_TRANSFER_MODE:
 730                 if ((imx_data->socdata->flags & ESDHC_FLAG_MULTIBLK_NO_INT)
 731                                 && (host->cmd->opcode == SD_IO_RW_EXTENDED)
 732                                 && (host->cmd->data->blocks > 1)
 733                                 && (host->cmd->data->flags & MMC_DATA_READ)) {
 734                         u32 v;
 735                         v = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
 736                         v |= ESDHC_VENDOR_SPEC_SDIO_QUIRK;
 737                         writel(v, host->ioaddr + ESDHC_VENDOR_SPEC);
 738                 }
 739
 740                 if (esdhc_is_usdhc(imx_data)) {
 741                         u32 wml;
 742                         u32 m = readl(host->ioaddr + ESDHC_MIX_CTRL);
 743                         /* Swap AC23 bit */
 744                         if (val & SDHCI_TRNS_AUTO_CMD23) {
 745                                 val &= ~SDHCI_TRNS_AUTO_CMD23;
 746                                 val |= ESDHC_MIX_CTRL_AC23EN;
 747                         }
 748                         m = val | (m & ~ESDHC_MIX_CTRL_SDHCI_MASK);
 749                         writel(m, host->ioaddr + ESDHC_MIX_CTRL);
 750
 751                         /* Set watermark levels for PIO access to maximum value
 752                          * (128 words) to accommodate full 512 bytes buffer.
 753                          * For DMA access restore the levels to default value.
 754                          */
 755                         m = readl(host->ioaddr + ESDHC_WTMK_LVL);
 756                         if (val & SDHCI_TRNS_DMA) {
 757                                 wml = ESDHC_WTMK_LVL_WML_VAL_DEF;
 758                         } else {
 759                                 u8 ctrl;
 760                                 wml = ESDHC_WTMK_LVL_WML_VAL_MAX;
 761
 762                                 /*
 763                                  * Since already disable DMA mode, so also need
 764                                  * to clear the DMASEL. Otherwise, for standard
 765                                  * tuning, when send tuning command, usdhc will
 766                                  * still prefetch the ADMA script from wrong
 767                                  * DMA address, then we will see IOMMU report
 768                                  * some error which show lack of TLB mapping.
 769                                  */
 770                                 ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
 771                                 ctrl &= ~SDHCI_CTRL_DMA_MASK;
 772                                 sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
 773                         }
 774                         m &= ~(ESDHC_WTMK_LVL_RD_WML_MASK |
 775                                ESDHC_WTMK_LVL_WR_WML_MASK);
 776                         m |= (wml << ESDHC_WTMK_LVL_RD_WML_SHIFT) |
 777                              (wml << ESDHC_WTMK_LVL_WR_WML_SHIFT);
 778                         writel(m, host->ioaddr + ESDHC_WTMK_LVL);
 779                 } else {
 780                         /*
 781                          * Postpone this write, we must do it together with a
 782                          * command write that is down below.
 783                          */
 784                         imx_data->scratchpad = val;
 785                 }
 786                 return;
 787         case SDHCI_COMMAND:
 788                 if (host->cmd->opcode == MMC_STOP_TRANSMISSION)
 789                         val |= SDHCI_CMD_ABORTCMD;
 790
 791                 if ((host->cmd->opcode == MMC_SET_BLOCK_COUNT) &&
 792                     (imx_data->socdata->flags & ESDHC_FLAG_MULTIBLK_NO_INT))
 793                         imx_data->multiblock_status = MULTIBLK_IN_PROCESS;
 794
 795                 if (esdhc_is_usdhc(imx_data))
 796                         writel(val << 16,
 797                                host->ioaddr + SDHCI_TRANSFER_MODE);
 798                 else
 799                         writel(val << 16 | imx_data->scratchpad,
 800                                host->ioaddr + SDHCI_TRANSFER_MODE);
 801                 return;
 802         case SDHCI_BLOCK_SIZE:
 803                 val &= ~SDHCI_MAKE_BLKSZ(0x7, 0);
 804                 break;
 805         }
 806         esdhc_clrset_le(host, 0xffff, val, reg);
 807 }
 808
 809 static u8 esdhc_readb_le(struct sdhci_host *host, int reg)
 810 {
 811         u8 ret;
 812         u32 val;
 813
 814         switch (reg) {
 815         case SDHCI_HOST_CONTROL:
 816                 val = readl(host->ioaddr + reg);
 817
 818                 ret = val & SDHCI_CTRL_LED;
 819                 ret |= (val >> 5) & SDHCI_CTRL_DMA_MASK;
 820                 ret |= (val & ESDHC_CTRL_4BITBUS);
 821                 ret |= (val & ESDHC_CTRL_8BITBUS) << 3;
 822                 return ret;
 823         }
 824
 825         return readb(host->ioaddr + reg);
 826 }
 827
 828 static void esdhc_writeb_le(struct sdhci_host *host, u8 val, int reg)
 829 {
 830         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 831         struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
 832         u32 new_val = 0;
 833         u32 mask;
 834
 835         switch (reg) {
 836         case SDHCI_POWER_CONTROL:
 837                 /*
 838                  * FSL put some DMA bits here
 839                  * If your board has a regulator, code should be here
 840                  */
 841                 return;
 842         case SDHCI_HOST_CONTROL:
 843                 /* FSL messed up here, so we need to manually compose it. */
 844                 new_val = val & SDHCI_CTRL_LED;
 845                 /* ensure the endianness */
 846                 new_val |= ESDHC_HOST_CONTROL_LE;
 847                 /* bits 8&9 are reserved on mx25 */
 848                 if (!is_imx25_esdhc(imx_data)) {
 849                         /* DMA mode bits are shifted */
 850                         new_val |= (val & SDHCI_CTRL_DMA_MASK) << 5;
 851                 }
 852
 853                 /*
 854                  * Do not touch buswidth bits here. This is done in
 855                  * esdhc_pltfm_bus_width.
 856                  * Do not touch the D3CD bit either which is used for the
 857                  * SDIO interrupt erratum workaround.
 858                  */
 859                 mask = 0xffff & ~(ESDHC_CTRL_BUSWIDTH_MASK | ESDHC_CTRL_D3CD);
 860
 861                 esdhc_clrset_le(host, mask, new_val, reg);
 862                 return;
 863         case SDHCI_SOFTWARE_RESET:
 864                 if (val & SDHCI_RESET_DATA)
 865                         new_val = readl(host->ioaddr + SDHCI_HOST_CONTROL);
 866                 break;
 867         }
 868         esdhc_clrset_le(host, 0xff, val, reg);
 869
 870         if (reg == SDHCI_SOFTWARE_RESET) {
 871                 if (val & SDHCI_RESET_ALL) {
 872                         /*
 873                          * The esdhc has a design violation to SDHC spec which
 874                          * tells that software reset should not affect card
 875                          * detection circuit. But esdhc clears its SYSCTL
 876                          * register bits [0..2] during the software reset. This
 877                          * will stop those clocks that card detection circuit
 878                          * relies on. To work around it, we turn the clocks on
 879                          * back to keep card detection circuit functional.
 880                          */
 881                         esdhc_clrset_le(host, 0x7, 0x7, ESDHC_SYSTEM_CONTROL);
 882                         /*
 883                          * The reset on usdhc fails to clear MIX_CTRL register.
 884                          * Do it manually here.
 885                          */
 886                         if (esdhc_is_usdhc(imx_data)) {
 887                                 /*
 888                                  * the tuning bits should be kept during reset
 889                                  */
 890                                 new_val = readl(host->ioaddr + ESDHC_MIX_CTRL);
 891                                 writel(new_val & ESDHC_MIX_CTRL_TUNING_MASK,
 892                                                 host->ioaddr + ESDHC_MIX_CTRL);
 893                                 imx_data->is_ddr = 0;
 894                         }
 895                 } else if (val & SDHCI_RESET_DATA) {
 896                         /*
 897                          * The eSDHC DAT line software reset clears at least the
 898                          * data transfer width on i.MX25, so make sure that the
 899                          * Host Control register is unaffected.
 900                          */
 901                         esdhc_clrset_le(host, 0xff, new_val,
 902                                         SDHCI_HOST_CONTROL);
 903                 }
 904         }
 905 }
 906
 907 static unsigned int esdhc_pltfm_get_max_clock(struct sdhci_host *host)
 908 {
 909         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 910
 911         return pltfm_host->clock;
 912 }
 913
 914 static unsigned int esdhc_pltfm_get_min_clock(struct sdhci_host *host)
 915 {
 916         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 917
 918         return pltfm_host->clock / 256 / 16;
 919 }
 920
 921 static inline void esdhc_pltfm_set_clock(struct sdhci_host *host,
 922                                          unsigned int clock)
 923 {
 924         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 925         struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
 926         unsigned int host_clock = pltfm_host->clock;
 927         int ddr_pre_div = imx_data->is_ddr ? 2 : 1;
 928         int pre_div = 1;
 929         int div = 1;
 930         int ret;
 931         u32 temp, val;
 932
 933         if (esdhc_is_usdhc(imx_data)) {
 934                 val = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
 935                 writel(val & ~ESDHC_VENDOR_SPEC_FRC_SDCLK_ON,
 936                         host->ioaddr + ESDHC_VENDOR_SPEC);
 937                 esdhc_wait_for_card_clock_gate_off(host);
 938         }
 939
 940         if (clock == 0) {
 941                 host->mmc->actual_clock = 0;
 942                 return;
 943         }
 944
 945         /* For i.MX53 eSDHCv3, SYSCTL.SDCLKFS may not be set to 0. */
 946         if (is_imx53_esdhc(imx_data)) {
 947                 /*
 948                  * According to the i.MX53 reference manual, if DLLCTRL[10] can
 949                  * be set, then the controller is eSDHCv3, else it is eSDHCv2.
 950                  */
 951                 val = readl(host->ioaddr + ESDHC_DLL_CTRL);
 952                 writel(val | BIT(10), host->ioaddr + ESDHC_DLL_CTRL);
 953                 temp = readl(host->ioaddr + ESDHC_DLL_CTRL);
 954                 writel(val, host->ioaddr + ESDHC_DLL_CTRL);
 955                 if (temp & BIT(10))
 956                         pre_div = 2;
 957         }
 958
 959         temp = sdhci_readl(host, ESDHC_SYSTEM_CONTROL);
 960         temp &= ~(ESDHC_CLOCK_IPGEN | ESDHC_CLOCK_HCKEN | ESDHC_CLOCK_PEREN
 961                 | ESDHC_CLOCK_MASK);
 962         sdhci_writel(host, temp, ESDHC_SYSTEM_CONTROL);
 963
 964         if (imx_data->socdata->flags & ESDHC_FLAG_ERR010450) {
 965                 unsigned int max_clock;
 966
 967                 max_clock = imx_data->is_ddr ? 45000000 : 150000000;
 968
 969                 clock = min(clock, max_clock);
 970         }
 971
 972         while (host_clock / (16 * pre_div * ddr_pre_div) > clock &&
 973                         pre_div < 256)
 974                 pre_div *= 2;
 975
 976         while (host_clock / (div * pre_div * ddr_pre_div) > clock && div < 16)
 977                 div++;
 978
 979         host->mmc->actual_clock = host_clock / (div * pre_div * ddr_pre_div);
 980         dev_dbg(mmc_dev(host->mmc), "desired SD clock: %d, actual: %d\n",
 981                 clock, host->mmc->actual_clock);
 982
 983         pre_div >>= 1;
 984         div--;
 985
 986         temp = sdhci_readl(host, ESDHC_SYSTEM_CONTROL);
 987         temp |= (ESDHC_CLOCK_IPGEN | ESDHC_CLOCK_HCKEN | ESDHC_CLOCK_PEREN
 988                 | (div << ESDHC_DIVIDER_SHIFT)
 989                 | (pre_div << ESDHC_PREDIV_SHIFT));
 990         sdhci_writel(host, temp, ESDHC_SYSTEM_CONTROL);
 991
 992         /* need to wait the bit 3 of the PRSSTAT to be set, make sure card clock is stable */
 993         ret = readl_poll_timeout(host->ioaddr + ESDHC_PRSSTAT, temp,
 994                                 (temp & ESDHC_CLOCK_STABLE), 2, 100);
 995         if (ret == -ETIMEDOUT)
 996                 dev_warn(mmc_dev(host->mmc), "card clock still not stable in 100us!.\n");
 997
 998         if (esdhc_is_usdhc(imx_data)) {
 999                 val = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
1000                 writel(val | ESDHC_VENDOR_SPEC_FRC_SDCLK_ON,
1001                         host->ioaddr + ESDHC_VENDOR_SPEC);
1002         }
1003
1004 }
1005
1006 static unsigned int esdhc_pltfm_get_ro(struct sdhci_host *host)
1007 {
1008         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1009         struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1010         struct esdhc_platform_data *boarddata = &imx_data->boarddata;
1011
1012         switch (boarddata->wp_type) {
1013         case ESDHC_WP_GPIO:
1014                 return mmc_gpio_get_ro(host->mmc);
1015         case ESDHC_WP_CONTROLLER:
1016                 return !(readl(host->ioaddr + SDHCI_PRESENT_STATE) &
1017                                SDHCI_WRITE_PROTECT);
1018         case ESDHC_WP_NONE:
1019                 break;
1020         }
1021
1022         return -ENOSYS;
1023 }
1024
1025 static void esdhc_pltfm_set_bus_width(struct sdhci_host *host, int width)
1026 {
1027         u32 ctrl;
1028
1029         switch (width) {
1030         case MMC_BUS_WIDTH_8:
1031                 ctrl = ESDHC_CTRL_8BITBUS;
1032                 break;
1033         case MMC_BUS_WIDTH_4:
1034                 ctrl = ESDHC_CTRL_4BITBUS;
1035                 break;
1036         default:
1037                 ctrl = 0;
1038                 break;
1039         }
1040
1041         esdhc_clrset_le(host, ESDHC_CTRL_BUSWIDTH_MASK, ctrl,
1042                         SDHCI_HOST_CONTROL);
1043 }
1044
1045 static void esdhc_reset_tuning(struct sdhci_host *host)
1046 {
1047         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1048         struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1049         u32 ctrl;
1050         int ret;
1051
1052         /* Reset the tuning circuit */
1053         if (esdhc_is_usdhc(imx_data)) {
1054                 ctrl = readl(host->ioaddr + ESDHC_MIX_CTRL);
1055                 ctrl &= ~ESDHC_MIX_CTRL_AUTO_TUNE_EN;
1056                 if (imx_data->socdata->flags & ESDHC_FLAG_MAN_TUNING) {
1057                         ctrl &= ~ESDHC_MIX_CTRL_SMPCLK_SEL;
1058                         ctrl &= ~ESDHC_MIX_CTRL_FBCLK_SEL;
1059                         writel(ctrl, host->ioaddr + ESDHC_MIX_CTRL);
1060                         writel(0, host->ioaddr + ESDHC_TUNE_CTRL_STATUS);
1061                 } else if (imx_data->socdata->flags & ESDHC_FLAG_STD_TUNING) {
1062                         writel(ctrl, host->ioaddr + ESDHC_MIX_CTRL);
1063                         ctrl = readl(host->ioaddr + SDHCI_AUTO_CMD_STATUS);
1064                         ctrl &= ~ESDHC_MIX_CTRL_SMPCLK_SEL;
1065                         ctrl &= ~ESDHC_MIX_CTRL_EXE_TUNE;
1066                         writel(ctrl, host->ioaddr + SDHCI_AUTO_CMD_STATUS);
1067                         /* Make sure ESDHC_MIX_CTRL_EXE_TUNE cleared */
1068                         ret = readl_poll_timeout(host->ioaddr + SDHCI_AUTO_CMD_STATUS,
1069                                 ctrl, !(ctrl & ESDHC_MIX_CTRL_EXE_TUNE), 1, 50);
1070                         if (ret == -ETIMEDOUT)
1071                                 dev_warn(mmc_dev(host->mmc),
1072                                  "Warning! clear execute tuning bit failed\n");
1073                         /*
1074                          * SDHCI_INT_DATA_AVAIL is W1C bit, set this bit will clear the
1075                          * usdhc IP internal logic flag execute_tuning_with_clr_buf, which
1076                          * will finally make sure the normal data transfer logic correct.
1077                          */
1078                         ctrl = readl(host->ioaddr + SDHCI_INT_STATUS);
1079                         ctrl |= SDHCI_INT_DATA_AVAIL;
1080                         writel(ctrl, host->ioaddr + SDHCI_INT_STATUS);
1081                 }
1082         }
1083 }
1084
1085 static void usdhc_init_card(struct mmc_host *mmc, struct mmc_card *card)
1086 {
1087         struct sdhci_host *host = mmc_priv(mmc);
1088         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1089         struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1090
1091         imx_data->init_card_type = card->type;
1092 }
1093
1094 static int usdhc_execute_tuning(struct mmc_host *mmc, u32 opcode)
1095 {
1096         struct sdhci_host *host = mmc_priv(mmc);
1097         int err;
1098
1099         /*
1100          * i.MX uSDHC internally already uses a fixed optimized timing for
1101          * DDR50, normally does not require tuning for DDR50 mode.
1102          */
1103         if (host->timing == MMC_TIMING_UHS_DDR50)
1104                 return 0;
1105
1106         /*
1107          * Reset tuning circuit logic. If not, the previous tuning result
1108          * will impact current tuning, make current tuning can't set the
1109          * correct delay cell.
1110          */
1111         esdhc_reset_tuning(host);
1112         err = sdhci_execute_tuning(mmc, opcode);
1113         /* If tuning done, enable auto tuning */
1114         if (!err && !host->tuning_err)
1115                 usdhc_auto_tuning_mode_sel_and_en(host);
1116
1117         return err;
1118 }
1119
1120 static void esdhc_prepare_tuning(struct sdhci_host *host, u32 val)
1121 {
1122         u32 reg;
1123         u8 sw_rst;
1124         int ret;
1125
1126         /* FIXME: delay a bit for card to be ready for next tuning due to errors */
1127         mdelay(1);
1128
1129         /* IC suggest to reset USDHC before every tuning command */
1130         esdhc_clrset_le(host, 0xff, SDHCI_RESET_ALL, SDHCI_SOFTWARE_RESET);
1131         ret = readb_poll_timeout(host->ioaddr + SDHCI_SOFTWARE_RESET, sw_rst,
1132                                 !(sw_rst & SDHCI_RESET_ALL), 10, 100);
1133         if (ret == -ETIMEDOUT)
1134                 dev_warn(mmc_dev(host->mmc),
1135                 "warning! RESET_ALL never complete before sending tuning command\n");
1136
1137         reg = readl(host->ioaddr + ESDHC_MIX_CTRL);
1138         reg |= ESDHC_MIX_CTRL_EXE_TUNE | ESDHC_MIX_CTRL_SMPCLK_SEL |
1139                         ESDHC_MIX_CTRL_FBCLK_SEL;
1140         writel(reg, host->ioaddr + ESDHC_MIX_CTRL);
1141         writel(val << 8, host->ioaddr + ESDHC_TUNE_CTRL_STATUS);
1142         dev_dbg(mmc_dev(host->mmc),
1143                 "tuning with delay 0x%x ESDHC_TUNE_CTRL_STATUS 0x%x\n",
1144                         val, readl(host->ioaddr + ESDHC_TUNE_CTRL_STATUS));
1145 }
1146
1147 static void esdhc_post_tuning(struct sdhci_host *host)
1148 {
1149         u32 reg;
1150
1151         reg = readl(host->ioaddr + ESDHC_MIX_CTRL);
1152         reg &= ~ESDHC_MIX_CTRL_EXE_TUNE;
1153         writel(reg, host->ioaddr + ESDHC_MIX_CTRL);
1154 }
1155
1156 static int esdhc_executing_tuning(struct sdhci_host *host, u32 opcode)
1157 {
1158         int min, max, avg, ret;
1159
1160         /* find the mininum delay first which can pass tuning */
1161         min = ESDHC_TUNE_CTRL_MIN;
1162         while (min < ESDHC_TUNE_CTRL_MAX) {
1163                 esdhc_prepare_tuning(host, min);
1164                 if (!mmc_send_tuning(host->mmc, opcode, NULL))
1165                         break;
1166                 min += ESDHC_TUNE_CTRL_STEP;
1167         }
1168
1169         /* find the maxinum delay which can not pass tuning */
1170         max = min + ESDHC_TUNE_CTRL_STEP;
1171         while (max < ESDHC_TUNE_CTRL_MAX) {
1172                 esdhc_prepare_tuning(host, max);
1173                 if (mmc_send_tuning(host->mmc, opcode, NULL)) {
1174                         max -= ESDHC_TUNE_CTRL_STEP;
1175                         break;
1176                 }
1177                 max += ESDHC_TUNE_CTRL_STEP;
1178         }
1179
1180         /* use average delay to get the best timing */
1181         avg = (min + max) / 2;
1182         esdhc_prepare_tuning(host, avg);
1183         ret = mmc_send_tuning(host->mmc, opcode, NULL);
1184         esdhc_post_tuning(host);
1185
1186         dev_dbg(mmc_dev(host->mmc), "tuning %s at 0x%x ret %d\n",
1187                 ret ? "failed" : "passed", avg, ret);
1188
1189         return ret;
1190 }
1191
1192 static void esdhc_hs400_enhanced_strobe(struct mmc_host *mmc, struct mmc_ios *ios)
1193 {
1194         struct sdhci_host *host = mmc_priv(mmc);
1195         u32 m;
1196
1197         m = readl(host->ioaddr + ESDHC_MIX_CTRL);
1198         if (ios->enhanced_strobe)
1199                 m |= ESDHC_MIX_CTRL_HS400_ES_EN;
1200         else
1201                 m &= ~ESDHC_MIX_CTRL_HS400_ES_EN;
1202         writel(m, host->ioaddr + ESDHC_MIX_CTRL);
1203 }
1204
1205 static int esdhc_change_pinstate(struct sdhci_host *host,
1206                                                 unsigned int uhs)
1207 {
1208         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1209         struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1210         struct pinctrl_state *pinctrl;
1211
1212         dev_dbg(mmc_dev(host->mmc), "change pinctrl state for uhs %d\n", uhs);
1213
1214         if (IS_ERR(imx_data->pinctrl) ||
1215                 IS_ERR(imx_data->pins_100mhz) ||
1216                 IS_ERR(imx_data->pins_200mhz))
1217                 return -EINVAL;
1218
1219         switch (uhs) {
1220         case MMC_TIMING_UHS_SDR50:
1221         case MMC_TIMING_UHS_DDR50:
1222                 pinctrl = imx_data->pins_100mhz;
1223                 break;
1224         case MMC_TIMING_UHS_SDR104:
1225         case MMC_TIMING_MMC_HS200:
1226         case MMC_TIMING_MMC_HS400:
1227                 pinctrl = imx_data->pins_200mhz;
1228                 break;
1229         default:
1230                 /* back to default state for other legacy timing */
1231                 return pinctrl_select_default_state(mmc_dev(host->mmc));
1232         }
1233
1234         return pinctrl_select_state(imx_data->pinctrl, pinctrl);
1235 }
1236
1237 /*
1238  * For HS400 eMMC, there is a data_strobe line. This signal is generated
1239  * by the device and used for data output and CRC status response output
1240  * in HS400 mode. The frequency of this signal follows the frequency of
1241  * CLK generated by host. The host receives the data which is aligned to the
1242  * edge of data_strobe line. Due to the time delay between CLK line and
1243  * data_strobe line, if the delay time is larger than one clock cycle,
1244  * then CLK and data_strobe line will be misaligned, read error shows up.
1245  */
1246 static void esdhc_set_strobe_dll(struct sdhci_host *host)
1247 {
1248         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1249         struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1250         u32 strobe_delay;
1251         u32 v;
1252         int ret;
1253
1254         /* disable clock before enabling strobe dll */
1255         writel(readl(host->ioaddr + ESDHC_VENDOR_SPEC) &
1256                 ~ESDHC_VENDOR_SPEC_FRC_SDCLK_ON,
1257                 host->ioaddr + ESDHC_VENDOR_SPEC);
1258         esdhc_wait_for_card_clock_gate_off(host);
1259
1260         /* force a reset on strobe dll */
1261         writel(ESDHC_STROBE_DLL_CTRL_RESET,
1262                 host->ioaddr + ESDHC_STROBE_DLL_CTRL);
1263         /* clear the reset bit on strobe dll before any setting */
1264         writel(0, host->ioaddr + ESDHC_STROBE_DLL_CTRL);
1265
1266         /*
1267          * enable strobe dll ctrl and adjust the delay target
1268          * for the uSDHC loopback read clock
1269          */
1270         if (imx_data->boarddata.strobe_dll_delay_target)
1271                 strobe_delay = imx_data->boarddata.strobe_dll_delay_target;
1272         else
1273                 strobe_delay = ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_DEFAULT;
1274         v = ESDHC_STROBE_DLL_CTRL_ENABLE |
1275                 ESDHC_STROBE_DLL_CTRL_SLV_UPDATE_INT_DEFAULT |
1276                 (strobe_delay << ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_SHIFT);
1277         writel(v, host->ioaddr + ESDHC_STROBE_DLL_CTRL);
1278
1279         /* wait max 50us to get the REF/SLV lock */
1280         ret = readl_poll_timeout(host->ioaddr + ESDHC_STROBE_DLL_STATUS, v,
1281                 ((v & ESDHC_STROBE_DLL_STS_REF_LOCK) && (v & ESDHC_STROBE_DLL_STS_SLV_LOCK)), 1, 50);
1282         if (ret == -ETIMEDOUT)
1283                 dev_warn(mmc_dev(host->mmc),
1284                 "warning! HS400 strobe DLL status REF/SLV not lock in 50us, STROBE DLL status is %x!\n", v);
1285 }
1286
1287 static void esdhc_set_uhs_signaling(struct sdhci_host *host, unsigned timing)
1288 {
1289         u32 m;
1290         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1291         struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1292         struct esdhc_platform_data *boarddata = &imx_data->boarddata;
1293
1294         /* disable ddr mode and disable HS400 mode */
1295         m = readl(host->ioaddr + ESDHC_MIX_CTRL);
1296         m &= ~(ESDHC_MIX_CTRL_DDREN | ESDHC_MIX_CTRL_HS400_EN);
1297         imx_data->is_ddr = 0;
1298
1299         switch (timing) {
1300         case MMC_TIMING_UHS_SDR12:
1301         case MMC_TIMING_UHS_SDR25:
1302         case MMC_TIMING_UHS_SDR50:
1303         case MMC_TIMING_UHS_SDR104:
1304         case MMC_TIMING_MMC_HS:
1305         case MMC_TIMING_MMC_HS200:
1306                 writel(m, host->ioaddr + ESDHC_MIX_CTRL);
1307                 break;
1308         case MMC_TIMING_UHS_DDR50:
1309         case MMC_TIMING_MMC_DDR52:
1310                 m |= ESDHC_MIX_CTRL_DDREN;
1311                 writel(m, host->ioaddr + ESDHC_MIX_CTRL);
1312                 imx_data->is_ddr = 1;
1313                 if (boarddata->delay_line) {
1314                         u32 v;
1315                         v = boarddata->delay_line <<
1316                                 ESDHC_DLL_OVERRIDE_VAL_SHIFT |
1317                                 (1 << ESDHC_DLL_OVERRIDE_EN_SHIFT);
1318                         if (is_imx53_esdhc(imx_data))
1319                                 v <<= 1;
1320                         writel(v, host->ioaddr + ESDHC_DLL_CTRL);
1321                 }
1322                 break;
1323         case MMC_TIMING_MMC_HS400:
1324                 m |= ESDHC_MIX_CTRL_DDREN | ESDHC_MIX_CTRL_HS400_EN;
1325                 writel(m, host->ioaddr + ESDHC_MIX_CTRL);
1326                 imx_data->is_ddr = 1;
1327                 /* update clock after enable DDR for strobe DLL lock */
1328                 host->ops->set_clock(host, host->clock);
1329                 esdhc_set_strobe_dll(host);
1330                 break;
1331         case MMC_TIMING_LEGACY:
1332         default:
1333                 esdhc_reset_tuning(host);
1334                 break;
1335         }
1336
1337         esdhc_change_pinstate(host, timing);
1338 }
1339
1340 static void esdhc_reset(struct sdhci_host *host, u8 mask)
1341 {
1342         sdhci_and_cqhci_reset(host, mask);
1343
1344         sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
1345         sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
1346 }
1347
1348 static unsigned int esdhc_get_max_timeout_count(struct sdhci_host *host)
1349 {
1350         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1351         struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1352
1353         /* Doc Erratum: the uSDHC actual maximum timeout count is 1 << 29 */
1354         return esdhc_is_usdhc(imx_data) ? 1 << 29 : 1 << 27;
1355 }
1356
1357 static void esdhc_set_timeout(struct sdhci_host *host, struct mmc_command *cmd)
1358 {
1359         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1360         struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1361
1362         /* use maximum timeout counter */
1363         esdhc_clrset_le(host, ESDHC_SYS_CTRL_DTOCV_MASK,
1364                         esdhc_is_usdhc(imx_data) ? 0xF : 0xE,
1365                         SDHCI_TIMEOUT_CONTROL);
1366 }
1367
1368 static u32 esdhc_cqhci_irq(struct sdhci_host *host, u32 intmask)
1369 {
1370         int cmd_error = 0;
1371         int data_error = 0;
1372
1373         if (!sdhci_cqe_irq(host, intmask, &cmd_error, &data_error))
1374                 return intmask;
1375
1376         cqhci_irq(host->mmc, intmask, cmd_error, data_error);
1377
1378         return 0;
1379 }
1380
1381 static struct sdhci_ops sdhci_esdhc_ops = {
1382         .read_l = esdhc_readl_le,
1383         .read_w = esdhc_readw_le,
1384         .read_b = esdhc_readb_le,
1385         .write_l = esdhc_writel_le,
1386         .write_w = esdhc_writew_le,
1387         .write_b = esdhc_writeb_le,
1388         .set_clock = esdhc_pltfm_set_clock,
1389         .get_max_clock = esdhc_pltfm_get_max_clock,
1390         .get_min_clock = esdhc_pltfm_get_min_clock,
1391         .get_max_timeout_count = esdhc_get_max_timeout_count,
1392         .get_ro = esdhc_pltfm_get_ro,
1393         .set_timeout = esdhc_set_timeout,
1394         .set_bus_width = esdhc_pltfm_set_bus_width,
1395         .set_uhs_signaling = esdhc_set_uhs_signaling,
1396         .reset = esdhc_reset,
1397         .irq = esdhc_cqhci_irq,
1398         .dump_vendor_regs = esdhc_dump_debug_regs,
1399 };
1400
1401 static const struct sdhci_pltfm_data sdhci_esdhc_imx_pdata = {
1402         .quirks = ESDHC_DEFAULT_QUIRKS | SDHCI_QUIRK_NO_HISPD_BIT
1403                         | SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC
1404                         | SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC
1405                         | SDHCI_QUIRK_BROKEN_CARD_DETECTION,
1406         .ops = &sdhci_esdhc_ops,
1407 };
1408
1409 static void sdhci_esdhc_imx_hwinit(struct sdhci_host *host)
1410 {
1411         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1412         struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1413         struct cqhci_host *cq_host = host->mmc->cqe_private;
1414         u32 tmp;
1415
1416         if (esdhc_is_usdhc(imx_data)) {
1417                 /*
1418                  * The imx6q ROM code will change the default watermark
1419                  * level setting to something insane.  Change it back here.
1420                  */
1421                 writel(ESDHC_WTMK_DEFAULT_VAL, host->ioaddr + ESDHC_WTMK_LVL);
1422
1423                 /*
1424                  * ROM code will change the bit burst_length_enable setting
1425                  * to zero if this usdhc is chosen to boot system. Change
1426                  * it back here, otherwise it will impact the performance a
1427                  * lot. This bit is used to enable/disable the burst length
1428                  * for the external AHB2AXI bridge. It's useful especially
1429                  * for INCR transfer because without burst length indicator,
1430                  * the AHB2AXI bridge does not know the burst length in
1431                  * advance. And without burst length indicator, AHB INCR
1432                  * transfer can only be converted to singles on the AXI side.
1433                  */
1434                 writel(readl(host->ioaddr + SDHCI_HOST_CONTROL)
1435                         | ESDHC_BURST_LEN_EN_INCR,
1436                         host->ioaddr + SDHCI_HOST_CONTROL);
1437
1438                 /*
1439                  * erratum ESDHC_FLAG_ERR004536 fix for MX6Q TO1.2 and MX6DL
1440                  * TO1.1, it's harmless for MX6SL
1441                  */
1442                 if (!(imx_data->socdata->flags & ESDHC_FLAG_SKIP_ERR004536)) {
1443                         writel(readl(host->ioaddr + 0x6c) & ~BIT(7),
1444                                 host->ioaddr + 0x6c);
1445                 }
1446
1447                 /* disable DLL_CTRL delay line settings */
1448                 writel(0x0, host->ioaddr + ESDHC_DLL_CTRL);
1449
1450                 /*
1451                  * For the case of command with busy, if set the bit
1452                  * ESDHC_VEND_SPEC2_EN_BUSY_IRQ, USDHC will generate a
1453                  * transfer complete interrupt when busy is deasserted.
1454                  * When CQHCI use DCMD to send a CMD need R1b respons,
1455                  * CQHCI require to set ESDHC_VEND_SPEC2_EN_BUSY_IRQ,
1456                  * otherwise DCMD will always meet timeout waiting for
1457                  * hardware interrupt issue.
1458                  */
1459                 if (imx_data->socdata->flags & ESDHC_FLAG_CQHCI) {
1460                         tmp = readl(host->ioaddr + ESDHC_VEND_SPEC2);
1461                         tmp |= ESDHC_VEND_SPEC2_EN_BUSY_IRQ;
1462                         writel(tmp, host->ioaddr + ESDHC_VEND_SPEC2);
1463
1464                         host->quirks &= ~SDHCI_QUIRK_NO_BUSY_IRQ;
1465                 }
1466
1467                 if (imx_data->socdata->flags & ESDHC_FLAG_STD_TUNING) {
1468                         tmp = readl(host->ioaddr + ESDHC_TUNING_CTRL);
1469                         tmp |= ESDHC_STD_TUNING_EN;
1470
1471                         /*
1472                          * ROM code or bootloader may config the start tap
1473                          * and step, unmask them first.
1474                          */
1475                         tmp &= ~(ESDHC_TUNING_START_TAP_MASK | ESDHC_TUNING_STEP_MASK);
1476                         if (imx_data->boarddata.tuning_start_tap)
1477                                 tmp |= imx_data->boarddata.tuning_start_tap;
1478                         else
1479                                 tmp |= ESDHC_TUNING_START_TAP_DEFAULT;
1480
1481                         if (imx_data->boarddata.tuning_step) {
1482                                 tmp |= imx_data->boarddata.tuning_step
1483                                         << ESDHC_TUNING_STEP_SHIFT;
1484                         } else {
1485                                 tmp |= ESDHC_TUNING_STEP_DEFAULT
1486                                         << ESDHC_TUNING_STEP_SHIFT;
1487                         }
1488
1489                         /* Disable the CMD CRC check for tuning, if not, need to
1490                          * add some delay after every tuning command, because
1491                          * hardware standard tuning logic will directly go to next
1492                          * step once it detect the CMD CRC error, will not wait for
1493                          * the card side to finally send out the tuning data, trigger
1494                          * the buffer read ready interrupt immediately. If usdhc send
1495                          * the next tuning command some eMMC card will stuck, can't
1496                          * response, block the tuning procedure or the first command
1497                          * after the whole tuning procedure always can't get any response.
1498                          */
1499                         tmp |= ESDHC_TUNING_CMD_CRC_CHECK_DISABLE;
1500                         writel(tmp, host->ioaddr + ESDHC_TUNING_CTRL);
1501                 } else if (imx_data->socdata->flags & ESDHC_FLAG_MAN_TUNING) {
1502                         /*
1503                          * ESDHC_STD_TUNING_EN may be configed in bootloader
1504                          * or ROM code, so clear this bit here to make sure
1505                          * the manual tuning can work.
1506                          */
1507                         tmp = readl(host->ioaddr + ESDHC_TUNING_CTRL);
1508                         tmp &= ~ESDHC_STD_TUNING_EN;
1509                         writel(tmp, host->ioaddr + ESDHC_TUNING_CTRL);
1510                 }
1511
1512                 /*
1513                  * On i.MX8MM, we are running Dual Linux OS, with 1st Linux using SD Card
1514                  * as rootfs storage, 2nd Linux using eMMC as rootfs storage. We let
1515                  * the 1st linux configure power/clock for the 2nd Linux.
1516                  *
1517                  * When the 2nd Linux is booting into rootfs stage, we let the 1st Linux
1518                  * to destroy the 2nd linux, then restart the 2nd linux, we met SDHCI dump.
1519                  * After we clear the pending interrupt and halt CQCTL, issue gone.
1520                  */
1521                 if (cq_host) {
1522                         tmp = cqhci_readl(cq_host, CQHCI_IS);
1523                         cqhci_writel(cq_host, tmp, CQHCI_IS);
1524                         cqhci_writel(cq_host, CQHCI_HALT, CQHCI_CTL);
1525                 }
1526         }
1527 }
1528
1529 static void esdhc_cqe_enable(struct mmc_host *mmc)
1530 {
1531         struct sdhci_host *host = mmc_priv(mmc);
1532         struct cqhci_host *cq_host = mmc->cqe_private;
1533         u32 reg;
1534         u16 mode;
1535         int count = 10;
1536
1537         /*
1538          * CQE gets stuck if it sees Buffer Read Enable bit set, which can be
1539          * the case after tuning, so ensure the buffer is drained.
1540          */
1541         reg = sdhci_readl(host, SDHCI_PRESENT_STATE);
1542         while (reg & SDHCI_DATA_AVAILABLE) {
1543                 sdhci_readl(host, SDHCI_BUFFER);
1544                 reg = sdhci_readl(host, SDHCI_PRESENT_STATE);
1545                 if (count-- == 0) {
1546                         dev_warn(mmc_dev(host->mmc),
1547                                 "CQE may get stuck because the Buffer Read Enable bit is set\n");
1548                         break;
1549                 }
1550                 mdelay(1);
1551         }
1552
1553         /*
1554          * Runtime resume will reset the entire host controller, which
1555          * will also clear the DMAEN/BCEN of register ESDHC_MIX_CTRL.
1556          * Here set DMAEN and BCEN when enable CMDQ.
1557          */
1558         mode = sdhci_readw(host, SDHCI_TRANSFER_MODE);
1559         if (host->flags & SDHCI_REQ_USE_DMA)
1560                 mode |= SDHCI_TRNS_DMA;
1561         if (!(host->quirks2 & SDHCI_QUIRK2_SUPPORT_SINGLE))
1562                 mode |= SDHCI_TRNS_BLK_CNT_EN;
1563         sdhci_writew(host, mode, SDHCI_TRANSFER_MODE);
1564
1565         /*
1566          * Though Runtime resume reset the entire host controller,
1567          * but do not impact the CQHCI side, need to clear the
1568          * HALT bit, avoid CQHCI stuck in the first request when
1569          * system resume back.
1570          */
1571         cqhci_writel(cq_host, 0, CQHCI_CTL);
1572         if (cqhci_readl(cq_host, CQHCI_CTL) & CQHCI_HALT)
1573                 dev_err(mmc_dev(host->mmc),
1574                         "failed to exit halt state when enable CQE\n");
1575
1576
1577         sdhci_cqe_enable(mmc);
1578 }
1579
1580 static void esdhc_sdhci_dumpregs(struct mmc_host *mmc)
1581 {
1582         sdhci_dumpregs(mmc_priv(mmc));
1583 }
1584
1585 static const struct cqhci_host_ops esdhc_cqhci_ops = {
1586         .enable         = esdhc_cqe_enable,
1587         .disable        = sdhci_cqe_disable,
1588         .dumpregs       = esdhc_sdhci_dumpregs,
1589 };
1590
1591 static int
1592 sdhci_esdhc_imx_probe_dt(struct platform_device *pdev,
1593                          struct sdhci_host *host,
1594                          struct pltfm_imx_data *imx_data)
1595 {
1596         struct device_node *np = pdev->dev.of_node;
1597         struct esdhc_platform_data *boarddata = &imx_data->boarddata;
1598         int ret;
1599
1600         if (of_property_read_bool(np, "fsl,wp-controller"))
1601                 boarddata->wp_type = ESDHC_WP_CONTROLLER;
1602
1603         /*
1604          * If we have this property, then activate WP check.
1605          * Retrieveing and requesting the actual WP GPIO will happen
1606          * in the call to mmc_of_parse().
1607          */
1608         if (of_property_read_bool(np, "wp-gpios"))
1609                 boarddata->wp_type = ESDHC_WP_GPIO;
1610
1611         of_property_read_u32(np, "fsl,tuning-step", &boarddata->tuning_step);
1612         of_property_read_u32(np, "fsl,tuning-start-tap",
1613                              &boarddata->tuning_start_tap);
1614
1615         of_property_read_u32(np, "fsl,strobe-dll-delay-target",
1616                                 &boarddata->strobe_dll_delay_target);
1617         if (of_property_read_bool(np, "no-1-8-v"))
1618                 host->quirks2 |= SDHCI_QUIRK2_NO_1_8_V;
1619
1620         if (of_property_read_u32(np, "fsl,delay-line", &boarddata->delay_line))
1621                 boarddata->delay_line = 0;
1622
1623         mmc_of_parse_voltage(host->mmc, &host->ocr_mask);
1624
1625         if (esdhc_is_usdhc(imx_data) && !IS_ERR(imx_data->pinctrl)) {
1626                 imx_data->pins_100mhz = pinctrl_lookup_state(imx_data->pinctrl,
1627                                                 ESDHC_PINCTRL_STATE_100MHZ);
1628                 imx_data->pins_200mhz = pinctrl_lookup_state(imx_data->pinctrl,
1629                                                 ESDHC_PINCTRL_STATE_200MHZ);
1630         }
1631
1632         /* call to generic mmc_of_parse to support additional capabilities */
1633         ret = mmc_of_parse(host->mmc);
1634         if (ret)
1635                 return ret;
1636
1637         /* HS400/HS400ES require 8 bit bus */
1638         if (!(host->mmc->caps & MMC_CAP_8_BIT_DATA))
1639                 host->mmc->caps2 &= ~(MMC_CAP2_HS400 | MMC_CAP2_HS400_ES);
1640
1641         if (mmc_gpio_get_cd(host->mmc) >= 0)
1642                 host->quirks &= ~SDHCI_QUIRK_BROKEN_CARD_DETECTION;
1643
1644         return 0;
1645 }
1646
1647 static int sdhci_esdhc_imx_probe(struct platform_device *pdev)
1648 {
1649         struct sdhci_pltfm_host *pltfm_host;
1650         struct sdhci_host *host;
1651         struct cqhci_host *cq_host;
1652         int err;
1653         struct pltfm_imx_data *imx_data;
1654
1655         host = sdhci_pltfm_init(pdev, &sdhci_esdhc_imx_pdata,
1656                                 sizeof(*imx_data));
1657         if (IS_ERR(host))
1658                 return PTR_ERR(host);
1659
1660         pltfm_host = sdhci_priv(host);
1661
1662         imx_data = sdhci_pltfm_priv(pltfm_host);
1663
1664         imx_data->socdata = device_get_match_data(&pdev->dev);
1665
1666         if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS)
1667                 cpu_latency_qos_add_request(&imx_data->pm_qos_req, 0);
1668
1669         imx_data->clk_ipg = devm_clk_get(&pdev->dev, "ipg");
1670         if (IS_ERR(imx_data->clk_ipg)) {
1671                 err = PTR_ERR(imx_data->clk_ipg);
1672                 goto free_sdhci;
1673         }
1674
1675         imx_data->clk_ahb = devm_clk_get(&pdev->dev, "ahb");
1676         if (IS_ERR(imx_data->clk_ahb)) {
1677                 err = PTR_ERR(imx_data->clk_ahb);
1678                 goto free_sdhci;
1679         }
1680
1681         imx_data->clk_per = devm_clk_get(&pdev->dev, "per");
1682         if (IS_ERR(imx_data->clk_per)) {
1683                 err = PTR_ERR(imx_data->clk_per);
1684                 goto free_sdhci;
1685         }
1686
1687         pltfm_host->clk = imx_data->clk_per;
1688         pltfm_host->clock = clk_get_rate(pltfm_host->clk);
1689         err = clk_prepare_enable(imx_data->clk_per);
1690         if (err)
1691                 goto free_sdhci;
1692         err = clk_prepare_enable(imx_data->clk_ipg);
1693         if (err)
1694                 goto disable_per_clk;
1695         err = clk_prepare_enable(imx_data->clk_ahb);
1696         if (err)
1697                 goto disable_ipg_clk;
1698
1699         imx_data->pinctrl = devm_pinctrl_get(&pdev->dev);
1700         if (IS_ERR(imx_data->pinctrl))
1701                 dev_warn(mmc_dev(host->mmc), "could not get pinctrl\n");
1702
1703         if (esdhc_is_usdhc(imx_data)) {
1704                 host->quirks2 |= SDHCI_QUIRK2_PRESET_VALUE_BROKEN;
1705                 host->mmc->caps |= MMC_CAP_1_8V_DDR | MMC_CAP_3_3V_DDR;
1706
1707                 /* GPIO CD can be set as a wakeup source */
1708                 host->mmc->caps |= MMC_CAP_CD_WAKE;
1709
1710                 if (!(imx_data->socdata->flags & ESDHC_FLAG_HS200))
1711                         host->quirks2 |= SDHCI_QUIRK2_BROKEN_HS200;
1712
1713                 /* clear tuning bits in case ROM has set it already */
1714                 writel(0x0, host->ioaddr + ESDHC_MIX_CTRL);
1715                 writel(0x0, host->ioaddr + SDHCI_AUTO_CMD_STATUS);
1716                 writel(0x0, host->ioaddr + ESDHC_TUNE_CTRL_STATUS);
1717
1718                 /*
1719                  * Link usdhc specific mmc_host_ops execute_tuning function,
1720                  * to replace the standard one in sdhci_ops.
1721                  */
1722                 host->mmc_host_ops.execute_tuning = usdhc_execute_tuning;
1723
1724                 /*
1725                  * Link usdhc specific mmc_host_ops init card function,
1726                  * to distinguish the card type.
1727                  */
1728                 host->mmc_host_ops.init_card = usdhc_init_card;
1729         }
1730
1731         if (imx_data->socdata->flags & ESDHC_FLAG_MAN_TUNING)
1732                 sdhci_esdhc_ops.platform_execute_tuning =
1733                                         esdhc_executing_tuning;
1734
1735         if (imx_data->socdata->flags & ESDHC_FLAG_ERR004536)
1736                 host->quirks |= SDHCI_QUIRK_BROKEN_ADMA;
1737
1738         if (imx_data->socdata->flags & ESDHC_FLAG_HS400)
1739                 host->mmc->caps2 |= MMC_CAP2_HS400;
1740
1741         if (imx_data->socdata->flags & ESDHC_FLAG_BROKEN_AUTO_CMD23)
1742                 host->quirks2 |= SDHCI_QUIRK2_ACMD23_BROKEN;
1743
1744         if (imx_data->socdata->flags & ESDHC_FLAG_HS400_ES) {
1745                 host->mmc->caps2 |= MMC_CAP2_HS400_ES;
1746                 host->mmc_host_ops.hs400_enhanced_strobe =
1747                                         esdhc_hs400_enhanced_strobe;
1748         }
1749
1750         if (imx_data->socdata->flags & ESDHC_FLAG_CQHCI) {
1751                 host->mmc->caps2 |= MMC_CAP2_CQE | MMC_CAP2_CQE_DCMD;
1752                 cq_host = devm_kzalloc(&pdev->dev, sizeof(*cq_host), GFP_KERNEL);
1753                 if (!cq_host) {
1754                         err = -ENOMEM;
1755                         goto disable_ahb_clk;
1756                 }
1757
1758                 cq_host->mmio = host->ioaddr + ESDHC_CQHCI_ADDR_OFFSET;
1759                 cq_host->ops = &esdhc_cqhci_ops;
1760
1761                 err = cqhci_init(cq_host, host->mmc, false);
1762                 if (err)
1763                         goto disable_ahb_clk;
1764         }
1765
1766         err = sdhci_esdhc_imx_probe_dt(pdev, host, imx_data);
1767         if (err)
1768                 goto disable_ahb_clk;
1769
1770         sdhci_esdhc_imx_hwinit(host);
1771
1772         err = sdhci_add_host(host);
1773         if (err)
1774                 goto disable_ahb_clk;
1775
1776         /*
1777          * Setup the wakeup capability here, let user to decide
1778          * whether need to enable this wakeup through sysfs interface.
1779          */
1780         if ((host->mmc->pm_caps & MMC_PM_KEEP_POWER) &&
1781                         (host->mmc->pm_caps & MMC_PM_WAKE_SDIO_IRQ))
1782                 device_set_wakeup_capable(&pdev->dev, true);
1783
1784         pm_runtime_set_active(&pdev->dev);
1785         pm_runtime_set_autosuspend_delay(&pdev->dev, 50);
1786         pm_runtime_use_autosuspend(&pdev->dev);
1787         pm_suspend_ignore_children(&pdev->dev, 1);
1788         pm_runtime_enable(&pdev->dev);
1789
1790         return 0;
1791
1792 disable_ahb_clk:
1793         clk_disable_unprepare(imx_data->clk_ahb);
1794 disable_ipg_clk:
1795         clk_disable_unprepare(imx_data->clk_ipg);
1796 disable_per_clk:
1797         clk_disable_unprepare(imx_data->clk_per);
1798 free_sdhci:
1799         if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS)
1800                 cpu_latency_qos_remove_request(&imx_data->pm_qos_req);
1801         sdhci_pltfm_free(pdev);
1802         return err;
1803 }
1804
1805 static int sdhci_esdhc_imx_remove(struct platform_device *pdev)
1806 {
1807         struct sdhci_host *host = platform_get_drvdata(pdev);
1808         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1809         struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1810         int dead;
1811
1812         pm_runtime_get_sync(&pdev->dev);
1813         dead = (readl(host->ioaddr + SDHCI_INT_STATUS) == 0xffffffff);
1814         pm_runtime_disable(&pdev->dev);
1815         pm_runtime_put_noidle(&pdev->dev);
1816
1817         sdhci_remove_host(host, dead);
1818
1819         clk_disable_unprepare(imx_data->clk_per);
1820         clk_disable_unprepare(imx_data->clk_ipg);
1821         clk_disable_unprepare(imx_data->clk_ahb);
1822
1823         if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS)
1824                 cpu_latency_qos_remove_request(&imx_data->pm_qos_req);
1825
1826         sdhci_pltfm_free(pdev);
1827
1828         return 0;
1829 }
1830
1831 #ifdef CONFIG_PM_SLEEP
1832 static int sdhci_esdhc_suspend(struct device *dev)
1833 {
1834         struct sdhci_host *host = dev_get_drvdata(dev);
1835         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1836         struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1837         int ret;
1838
1839         if (host->mmc->caps2 & MMC_CAP2_CQE) {
1840                 ret = cqhci_suspend(host->mmc);
1841                 if (ret)
1842                         return ret;
1843         }
1844
1845         if ((imx_data->socdata->flags & ESDHC_FLAG_STATE_LOST_IN_LPMODE) &&
1846                 (host->tuning_mode != SDHCI_TUNING_MODE_1)) {
1847                 mmc_retune_timer_stop(host->mmc);
1848                 mmc_retune_needed(host->mmc);
1849         }
1850
1851         if (host->tuning_mode != SDHCI_TUNING_MODE_3)
1852                 mmc_retune_needed(host->mmc);
1853
1854         ret = sdhci_suspend_host(host);
1855         if (ret)
1856                 return ret;
1857
1858         ret = pinctrl_pm_select_sleep_state(dev);
1859         if (ret)
1860                 return ret;
1861
1862         ret = mmc_gpio_set_cd_wake(host->mmc, true);
1863
1864         return ret;
1865 }
1866
1867 static int sdhci_esdhc_resume(struct device *dev)
1868 {
1869         struct sdhci_host *host = dev_get_drvdata(dev);
1870         int ret;
1871
1872         ret = pinctrl_pm_select_default_state(dev);
1873         if (ret)
1874                 return ret;
1875
1876         /* re-initialize hw state in case it's lost in low power mode */
1877         sdhci_esdhc_imx_hwinit(host);
1878
1879         ret = sdhci_resume_host(host);
1880         if (ret)
1881                 return ret;
1882
1883         if (host->mmc->caps2 & MMC_CAP2_CQE)
1884                 ret = cqhci_resume(host->mmc);
1885
1886         if (!ret)
1887                 ret = mmc_gpio_set_cd_wake(host->mmc, false);
1888
1889         return ret;
1890 }
1891 #endif
1892
1893 #ifdef CONFIG_PM
1894 static int sdhci_esdhc_runtime_suspend(struct device *dev)
1895 {
1896         struct sdhci_host *host = dev_get_drvdata(dev);
1897         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1898         struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1899         int ret;
1900
1901         if (host->mmc->caps2 & MMC_CAP2_CQE) {
1902                 ret = cqhci_suspend(host->mmc);
1903                 if (ret)
1904                         return ret;
1905         }
1906
1907         ret = sdhci_runtime_suspend_host(host);
1908         if (ret)
1909                 return ret;
1910
1911         if (host->tuning_mode != SDHCI_TUNING_MODE_3)
1912                 mmc_retune_needed(host->mmc);
1913
1914         imx_data->actual_clock = host->mmc->actual_clock;
1915         esdhc_pltfm_set_clock(host, 0);
1916         clk_disable_unprepare(imx_data->clk_per);
1917         clk_disable_unprepare(imx_data->clk_ipg);
1918         clk_disable_unprepare(imx_data->clk_ahb);
1919
1920         if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS)
1921                 cpu_latency_qos_remove_request(&imx_data->pm_qos_req);
1922
1923         return ret;
1924 }
1925
1926 static int sdhci_esdhc_runtime_resume(struct device *dev)
1927 {
1928         struct sdhci_host *host = dev_get_drvdata(dev);
1929         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1930         struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1931         int err;
1932
1933         if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS)
1934                 cpu_latency_qos_add_request(&imx_data->pm_qos_req, 0);
1935
1936         if (imx_data->socdata->flags & ESDHC_FLAG_CLK_RATE_LOST_IN_PM_RUNTIME)
1937                 clk_set_rate(imx_data->clk_per, pltfm_host->clock);
1938
1939         err = clk_prepare_enable(imx_data->clk_ahb);
1940         if (err)
1941                 goto remove_pm_qos_request;
1942
1943         err = clk_prepare_enable(imx_data->clk_per);
1944         if (err)
1945                 goto disable_ahb_clk;
1946
1947         err = clk_prepare_enable(imx_data->clk_ipg);
1948         if (err)
1949                 goto disable_per_clk;
1950
1951         esdhc_pltfm_set_clock(host, imx_data->actual_clock);
1952
1953         err = sdhci_runtime_resume_host(host, 0);
1954         if (err)
1955                 goto disable_ipg_clk;
1956
1957         if (host->mmc->caps2 & MMC_CAP2_CQE)
1958                 err = cqhci_resume(host->mmc);
1959
1960         return err;
1961
1962 disable_ipg_clk:
1963         clk_disable_unprepare(imx_data->clk_ipg);
1964 disable_per_clk:
1965         clk_disable_unprepare(imx_data->clk_per);
1966 disable_ahb_clk:
1967         clk_disable_unprepare(imx_data->clk_ahb);
1968 remove_pm_qos_request:
1969         if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS)
1970                 cpu_latency_qos_remove_request(&imx_data->pm_qos_req);
1971         return err;
1972 }
1973 #endif
1974
1975 static const struct dev_pm_ops sdhci_esdhc_pmops = {
1976         SET_SYSTEM_SLEEP_PM_OPS(sdhci_esdhc_suspend, sdhci_esdhc_resume)
1977         SET_RUNTIME_PM_OPS(sdhci_esdhc_runtime_suspend,
1978                                 sdhci_esdhc_runtime_resume, NULL)
1979 };
1980
1981 static struct platform_driver sdhci_esdhc_imx_driver = {
1982         .driver         = {
1983                 .name   = "sdhci-esdhc-imx",
1984                 .probe_type = PROBE_PREFER_ASYNCHRONOUS,
1985                 .of_match_table = imx_esdhc_dt_ids,
1986                 .pm     = &sdhci_esdhc_pmops,
1987         },
1988         .probe          = sdhci_esdhc_imx_probe,
1989         .remove         = sdhci_esdhc_imx_remove,
1990 };
1991
1992 module_platform_driver(sdhci_esdhc_imx_driver);
1993
1994 MODULE_DESCRIPTION("SDHCI driver for Freescale i.MX eSDHC");
1995 MODULE_AUTHOR("Wolfram Sang <[email protected]>");
1996 MODULE_LICENSE("GPL v2");