2 # (C) Copyright 2000 - 2005
5 # See file CREDITS for list of people who contributed to this
8 # This program is free software; you can redistribute it and/or
9 # modify it under the terms of the GNU General Public License as
10 # published by the Free Software Foundation; either version 2 of
11 # the License, or (at your option) any later version.
13 # This program is distributed in the hope that it will be useful,
14 # but WITHOUT ANY WARRANTY; without even the implied warranty of
15 # MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
16 # GNU General Public License for more details.
18 # You should have received a copy of the GNU General Public License
19 # along with this program; if not, write to the Free Software
20 # Foundation, Inc., 59 Temple Place, Suite 330, Boston,
27 This directory contains the source code for U-Boot, a boot loader for
28 Embedded boards based on PowerPC, ARM, MIPS and several other
29 processors, which can be installed in a boot ROM and used to
30 initialize and test the hardware or to download and run application
33 The development of U-Boot is closely related to Linux: some parts of
34 the source code originate in the Linux source tree, we have some
35 header files in common, and special provision has been made to
36 support booting of Linux images.
38 Some attention has been paid to make this software easily
39 configurable and extendable. For instance, all monitor commands are
40 implemented with the same call interface, so that it's very easy to
41 add new commands. Also, instead of permanently adding rarely used
42 code (for instance hardware test utilities) to the monitor, you can
43 load and run it dynamically.
49 In general, all boards for which a configuration option exists in the
50 Makefile have been tested to some extent and can be considered
51 "working". In fact, many of them are used in production systems.
53 In case of problems see the CHANGELOG and CREDITS files to find out
54 who contributed the specific port.
60 In case you have questions about, problems with or contributions for
61 U-Boot you should send a message to the U-Boot mailing list at
63 previous traffic on the mailing list - please search the archive
64 before asking FAQ's. Please see
65 http://lists.sourceforge.net/lists/listinfo/u-boot-users/
71 - start from 8xxrom sources
72 - create PPCBoot project (http://sourceforge.net/projects/ppcboot)
74 - make it easier to add custom boards
75 - make it possible to add other [PowerPC] CPUs
76 - extend functions, especially:
77 * Provide extended interface to Linux boot loader
80 * PCMCIA / CompactFLash / ATA disk / SCSI ... boot
81 - create ARMBoot project (http://sourceforge.net/projects/armboot)
82 - add other CPU families (starting with ARM)
83 - create U-Boot project (http://sourceforge.net/projects/u-boot)
89 The "official" name of this project is "Das U-Boot". The spelling
90 "U-Boot" shall be used in all written text (documentation, comments
91 in source files etc.). Example:
93 This is the README file for the U-Boot project.
95 File names etc. shall be based on the string "u-boot". Examples:
97 include/asm-ppc/u-boot.h
99 #include <asm/u-boot.h>
101 Variable names, preprocessor constants etc. shall be either based on
102 the string "u_boot" or on "U_BOOT". Example:
104 U_BOOT_VERSION u_boot_logo
105 IH_OS_U_BOOT u_boot_hush_start
111 U-Boot uses a 3 level version number containing a version, a
112 sub-version, and a patchlevel: "U-Boot-2.34.5" means version "2",
113 sub-version "34", and patchlevel "4".
115 The patchlevel is used to indicate certain stages of development
116 between released versions, i. e. officially released versions of
117 U-Boot will always have a patchlevel of "0".
123 - board Board dependent files
124 - common Misc architecture independent functions
125 - cpu CPU specific files
126 - 74xx_7xx Files specific to Freescale MPC74xx and 7xx CPUs
127 - arm720t Files specific to ARM 720 CPUs
128 - arm920t Files specific to ARM 920 CPUs
129 - at91rm9200 Files specific to Atmel AT91RM9200 CPU
130 - imx Files specific to Freescale MC9328 i.MX CPUs
131 - s3c24x0 Files specific to Samsung S3C24X0 CPUs
132 - arm925t Files specific to ARM 925 CPUs
133 - arm926ejs Files specific to ARM 926 CPUs
134 - arm1136 Files specific to ARM 1136 CPUs
135 - i386 Files specific to i386 CPUs
136 - ixp Files specific to Intel XScale IXP CPUs
137 - mcf52x2 Files specific to Freescale ColdFire MCF52x2 CPUs
138 - mips Files specific to MIPS CPUs
139 - mpc5xx Files specific to Freescale MPC5xx CPUs
140 - mpc5xxx Files specific to Freescale MPC5xxx CPUs
141 - mpc8xx Files specific to Freescale MPC8xx CPUs
142 - mpc8220 Files specific to Freescale MPC8220 CPUs
143 - mpc824x Files specific to Freescale MPC824x CPUs
144 - mpc8260 Files specific to Freescale MPC8260 CPUs
145 - mpc85xx Files specific to Freescale MPC85xx CPUs
146 - nios Files specific to Altera NIOS CPUs
147 - nios2 Files specific to Altera Nios-II CPUs
148 - ppc4xx Files specific to AMCC PowerPC 4xx CPUs
149 - pxa Files specific to Intel XScale PXA CPUs
150 - s3c44b0 Files specific to Samsung S3C44B0 CPUs
151 - sa1100 Files specific to Intel StrongARM SA1100 CPUs
152 - disk Code for disk drive partition handling
153 - doc Documentation (don't expect too much)
154 - drivers Commonly used device drivers
155 - dtt Digital Thermometer and Thermostat drivers
156 - examples Example code for standalone applications, etc.
157 - include Header Files
158 - lib_arm Files generic to ARM architecture
159 - lib_generic Files generic to all architectures
160 - lib_i386 Files generic to i386 architecture
161 - lib_m68k Files generic to m68k architecture
162 - lib_mips Files generic to MIPS architecture
163 - lib_nios Files generic to NIOS architecture
164 - lib_ppc Files generic to PowerPC architecture
165 - net Networking code
166 - post Power On Self Test
167 - rtc Real Time Clock drivers
168 - tools Tools to build S-Record or U-Boot images, etc.
170 Software Configuration:
171 =======================
173 Configuration is usually done using C preprocessor defines; the
174 rationale behind that is to avoid dead code whenever possible.
176 There are two classes of configuration variables:
178 * Configuration _OPTIONS_:
179 These are selectable by the user and have names beginning with
182 * Configuration _SETTINGS_:
183 These depend on the hardware etc. and should not be meddled with if
184 you don't know what you're doing; they have names beginning with
187 Later we will add a configuration tool - probably similar to or even
188 identical to what's used for the Linux kernel. Right now, we have to
189 do the configuration by hand, which means creating some symbolic
190 links and editing some configuration files. We use the TQM8xxL boards
194 Selection of Processor Architecture and Board Type:
195 ---------------------------------------------------
197 For all supported boards there are ready-to-use default
198 configurations available; just type "make <board_name>_config".
200 Example: For a TQM823L module type:
205 For the Cogent platform, you need to specify the cpu type as well;
206 e.g. "make cogent_mpc8xx_config". And also configure the cogent
207 directory according to the instructions in cogent/README.
210 Configuration Options:
211 ----------------------
213 Configuration depends on the combination of board and CPU type; all
214 such information is kept in a configuration file
215 "include/configs/<board_name>.h".
217 Example: For a TQM823L module, all configuration settings are in
218 "include/configs/TQM823L.h".
221 Many of the options are named exactly as the corresponding Linux
222 kernel configuration options. The intention is to make it easier to
223 build a config tool - later.
226 The following options need to be configured:
228 - CPU Type: Define exactly one of
232 CONFIG_MPC823, CONFIG_MPC850, CONFIG_MPC855, CONFIG_MPC860
235 or CONFIG_MPC824X, CONFIG_MPC8260
250 MicroBlaze based CPUs:
251 ----------------------
255 ----------------------
259 - Board Type: Define exactly one of
261 PowerPC based boards:
262 ---------------------
264 CONFIG_ADCIOP CONFIG_GEN860T CONFIG_PCI405
265 CONFIG_ADS860 CONFIG_GENIETV CONFIG_PCIPPC2
266 CONFIG_AMX860 CONFIG_GTH CONFIG_PCIPPC6
267 CONFIG_AR405 CONFIG_gw8260 CONFIG_pcu_e
268 CONFIG_BAB7xx CONFIG_hermes CONFIG_PIP405
269 CONFIG_c2mon CONFIG_hymod CONFIG_PM826
270 CONFIG_CANBT CONFIG_IAD210 CONFIG_ppmc8260
271 CONFIG_CCM CONFIG_ICU862 CONFIG_QS823
272 CONFIG_CMI CONFIG_IP860 CONFIG_QS850
273 CONFIG_cogent_mpc8260 CONFIG_IPHASE4539 CONFIG_QS860T
274 CONFIG_cogent_mpc8xx CONFIG_IVML24 CONFIG_RBC823
275 CONFIG_CPCI405 CONFIG_IVML24_128 CONFIG_RPXClassic
276 CONFIG_CPCI4052 CONFIG_IVML24_256 CONFIG_RPXlite
277 CONFIG_CPCIISER4 CONFIG_IVMS8 CONFIG_RPXsuper
278 CONFIG_CPU86 CONFIG_IVMS8_128 CONFIG_rsdproto
279 CONFIG_CRAYL1 CONFIG_IVMS8_256 CONFIG_sacsng
280 CONFIG_CSB272 CONFIG_JSE CONFIG_Sandpoint8240
281 CONFIG_CU824 CONFIG_LANTEC CONFIG_Sandpoint8245
282 CONFIG_DASA_SIM CONFIG_lwmon CONFIG_sbc8260
283 CONFIG_DB64360 CONFIG_MBX CONFIG_sbc8560
284 CONFIG_DB64460 CONFIG_MBX860T CONFIG_SM850
285 CONFIG_DU405 CONFIG_MHPC CONFIG_SPD823TS
286 CONFIG_DUET_ADS CONFIG_MIP405 CONFIG_STXGP3
287 CONFIG_EBONY CONFIG_MOUSSE CONFIG_SXNI855T
288 CONFIG_ELPPC CONFIG_MPC8260ADS CONFIG_TQM823L
289 CONFIG_ELPT860 CONFIG_MPC8540ADS CONFIG_TQM8260
290 CONFIG_ep8260 CONFIG_MPC8540EVAL CONFIG_TQM850L
291 CONFIG_ERIC CONFIG_MPC8560ADS CONFIG_TQM855L
292 CONFIG_ESTEEM192E CONFIG_MUSENKI CONFIG_TQM860L
293 CONFIG_ETX094 CONFIG_MVS1 CONFIG_TTTech
294 CONFIG_EVB64260 CONFIG_NETPHONE CONFIG_UTX8245
295 CONFIG_FADS823 CONFIG_NETTA CONFIG_V37
296 CONFIG_FADS850SAR CONFIG_NETVIA CONFIG_W7OLMC
297 CONFIG_FADS860T CONFIG_NX823 CONFIG_W7OLMG
298 CONFIG_FLAGADM CONFIG_OCRTC CONFIG_WALNUT
299 CONFIG_FPS850L CONFIG_ORSG CONFIG_ZPC1900
300 CONFIG_FPS860L CONFIG_OXC CONFIG_ZUMA
305 CONFIG_AT91RM9200DK, CONFIG_CERF250, CONFIG_DNP1110,
306 CONFIG_EP7312, CONFIG_H2_OMAP1610, CONFIG_HHP_CRADLE,
307 CONFIG_IMPA7, CONFIG_INNOVATOROMAP1510, CONFIG_INNOVATOROMAP1610,
308 CONFIG_LART, CONFIG_LPD7A400 CONFIG_LUBBOCK,
309 CONFIG_OSK_OMAP5912, CONFIG_OMAP2420H4, CONFIG_SHANNON,
310 CONFIG_P2_OMAP730, CONFIG_SMDK2400, CONFIG_SMDK2410,
311 CONFIG_TRAB, CONFIG_VCMA9
313 MicroBlaze based boards:
314 ------------------------
319 ------------------------
321 CONFIG_PCI5441 CONFIG_PK1C20
324 - CPU Module Type: (if CONFIG_COGENT is defined)
325 Define exactly one of
327 --- FIXME --- not tested yet:
328 CONFIG_CMA286_60, CONFIG_CMA286_21, CONFIG_CMA286_60P,
329 CONFIG_CMA287_23, CONFIG_CMA287_50
331 - Motherboard Type: (if CONFIG_COGENT is defined)
332 Define exactly one of
333 CONFIG_CMA101, CONFIG_CMA102
335 - Motherboard I/O Modules: (if CONFIG_COGENT is defined)
336 Define one or more of
339 - Motherboard Options: (if CONFIG_CMA101 or CONFIG_CMA102 are defined)
340 Define one or more of
341 CONFIG_LCD_HEARTBEAT - update a character position on
342 the lcd display every second with
345 - Board flavour: (if CONFIG_MPC8260ADS is defined)
348 CFG_8260ADS - original MPC8260ADS
349 CFG_8266ADS - MPC8266ADS
350 CFG_PQ2FADS - PQ2FADS-ZU or PQ2FADS-VR
351 CFG_8272ADS - MPC8272ADS
353 - MPC824X Family Member (if CONFIG_MPC824X is defined)
354 Define exactly one of
355 CONFIG_MPC8240, CONFIG_MPC8245
357 - 8xx CPU Options: (if using an MPC8xx cpu)
358 CONFIG_8xx_GCLK_FREQ - deprecated: CPU clock if
359 get_gclk_freq() cannot work
360 e.g. if there is no 32KHz
361 reference PIT/RTC clock
362 CONFIG_8xx_OSCLK - PLL input clock (either EXTCLK
365 - 859/866/885 CPU options: (if using a MPC859 or MPC866 or MPC885 CPU):
368 CONFIG_8xx_CPUCLK_DEFAULT
369 See doc/README.MPC866
373 Define this to measure the actual CPU clock instead
374 of relying on the correctness of the configured
375 values. Mostly useful for board bringup to make sure
376 the PLL is locked at the intended frequency. Note
377 that this requires a (stable) reference clock (32 kHz
378 RTC clock or CFG_8XX_XIN)
380 - Linux Kernel Interface:
383 U-Boot stores all clock information in Hz
384 internally. For binary compatibility with older Linux
385 kernels (which expect the clocks passed in the
386 bd_info data to be in MHz) the environment variable
387 "clocks_in_mhz" can be defined so that U-Boot
388 converts clock data to MHZ before passing it to the
390 When CONFIG_CLOCKS_IN_MHZ is defined, a definition of
391 "clocks_in_mhz=1" is automatically included in the
394 CONFIG_MEMSIZE_IN_BYTES [relevant for MIPS only]
396 When transfering memsize parameter to linux, some versions
397 expect it to be in bytes, others in MB.
398 Define CONFIG_MEMSIZE_IN_BYTES to make it in bytes.
403 Define this if you want support for Amba PrimeCell PL010 UARTs.
407 Define this if you want support for Amba PrimeCell PL011 UARTs.
411 If you have Amba PrimeCell PL011 UARTs, set this variable to
412 the clock speed of the UARTs.
416 If you have Amba PrimeCell PL010 or PL011 UARTs on your board,
417 define this to a list of base addresses for each (supported)
418 port. See e.g. include/configs/versatile.h
422 Depending on board, define exactly one serial port
423 (like CONFIG_8xx_CONS_SMC1, CONFIG_8xx_CONS_SMC2,
424 CONFIG_8xx_CONS_SCC1, ...), or switch off the serial
425 console by defining CONFIG_8xx_CONS_NONE
427 Note: if CONFIG_8xx_CONS_NONE is defined, the serial
428 port routines must be defined elsewhere
429 (i.e. serial_init(), serial_getc(), ...)
432 Enables console device for a color framebuffer. Needs following
433 defines (cf. smiLynxEM, i8042, board/eltec/bab7xx)
434 VIDEO_FB_LITTLE_ENDIAN graphic memory organisation
436 VIDEO_HW_RECTFILL graphic chip supports
439 VIDEO_HW_BITBLT graphic chip supports
440 bit-blit (cf. smiLynxEM)
441 VIDEO_VISIBLE_COLS visible pixel columns
443 VIDEO_VISIBLE_ROWS visible pixel rows
444 VIDEO_PIXEL_SIZE bytes per pixel
445 VIDEO_DATA_FORMAT graphic data format
446 (0-5, cf. cfb_console.c)
447 VIDEO_FB_ADRS framebuffer address
448 VIDEO_KBD_INIT_FCT keyboard int fct
449 (i.e. i8042_kbd_init())
450 VIDEO_TSTC_FCT test char fct
452 VIDEO_GETC_FCT get char fct
454 CONFIG_CONSOLE_CURSOR cursor drawing on/off
455 (requires blink timer
457 CFG_CONSOLE_BLINK_COUNT blink interval (cf. i8042.c)
458 CONFIG_CONSOLE_TIME display time/date info in
460 (requires CFG_CMD_DATE)
461 CONFIG_VIDEO_LOGO display Linux logo in
463 CONFIG_VIDEO_BMP_LOGO use bmp_logo.h instead of
464 linux_logo.h for logo.
465 Requires CONFIG_VIDEO_LOGO
466 CONFIG_CONSOLE_EXTRA_INFO
467 addional board info beside
470 When CONFIG_CFB_CONSOLE is defined, video console is
471 default i/o. Serial console can be forced with
472 environment 'console=serial'.
474 When CONFIG_SILENT_CONSOLE is defined, all console
475 messages (by U-Boot and Linux!) can be silenced with
476 the "silent" environment variable. See
477 doc/README.silent for more information.
480 CONFIG_BAUDRATE - in bps
481 Select one of the baudrates listed in
482 CFG_BAUDRATE_TABLE, see below.
483 CFG_BRGCLK_PRESCALE, baudrate prescale
485 - Interrupt driven serial port input:
486 CONFIG_SERIAL_SOFTWARE_FIFO
489 Use an interrupt handler for receiving data on the
490 serial port. It also enables using hardware handshake
491 (RTS/CTS) and UART's built-in FIFO. Set the number of
492 bytes the interrupt driven input buffer should have.
494 Leave undefined to disable this feature, including
495 disable the buffer and hardware handshake.
497 - Console UART Number:
501 If defined internal UART1 (and not UART0) is used
502 as default U-Boot console.
504 - Boot Delay: CONFIG_BOOTDELAY - in seconds
505 Delay before automatically booting the default image;
506 set to -1 to disable autoboot.
508 See doc/README.autoboot for these options that
509 work with CONFIG_BOOTDELAY. None are required.
510 CONFIG_BOOT_RETRY_TIME
511 CONFIG_BOOT_RETRY_MIN
512 CONFIG_AUTOBOOT_KEYED
513 CONFIG_AUTOBOOT_PROMPT
514 CONFIG_AUTOBOOT_DELAY_STR
515 CONFIG_AUTOBOOT_STOP_STR
516 CONFIG_AUTOBOOT_DELAY_STR2
517 CONFIG_AUTOBOOT_STOP_STR2
518 CONFIG_ZERO_BOOTDELAY_CHECK
519 CONFIG_RESET_TO_RETRY
523 Only needed when CONFIG_BOOTDELAY is enabled;
524 define a command string that is automatically executed
525 when no character is read on the console interface
526 within "Boot Delay" after reset.
529 This can be used to pass arguments to the bootm
530 command. The value of CONFIG_BOOTARGS goes into the
531 environment value "bootargs".
533 CONFIG_RAMBOOT and CONFIG_NFSBOOT
534 The value of these goes into the environment as
535 "ramboot" and "nfsboot" respectively, and can be used
536 as a convenience, when switching between booting from
542 When this option is #defined, the existence of the
543 environment variable "preboot" will be checked
544 immediately before starting the CONFIG_BOOTDELAY
545 countdown and/or running the auto-boot command resp.
546 entering interactive mode.
548 This feature is especially useful when "preboot" is
549 automatically generated or modified. For an example
550 see the LWMON board specific code: here "preboot" is
551 modified when the user holds down a certain
552 combination of keys on the (special) keyboard when
555 - Serial Download Echo Mode:
557 If defined to 1, all characters received during a
558 serial download (using the "loads" command) are
559 echoed back. This might be needed by some terminal
560 emulations (like "cu"), but may as well just take
561 time on others. This setting #define's the initial
562 value of the "loads_echo" environment variable.
564 - Kgdb Serial Baudrate: (if CFG_CMD_KGDB is defined)
566 Select one of the baudrates listed in
567 CFG_BAUDRATE_TABLE, see below.
571 Most monitor functions can be selected (or
572 de-selected) by adjusting the definition of
573 CONFIG_COMMANDS; to select individual functions,
574 #define CONFIG_COMMANDS by "OR"ing any of the
577 #define enables commands:
578 -------------------------
579 CFG_CMD_ASKENV * ask for env variable
580 CFG_CMD_AUTOSCRIPT Autoscript Support
582 CFG_CMD_BEDBUG * Include BedBug Debugger
583 CFG_CMD_BMP * BMP support
584 CFG_CMD_BSP * Board specific commands
586 CFG_CMD_CACHE * icache, dcache
587 CFG_CMD_CONSOLE coninfo
588 CFG_CMD_DATE * support for RTC, date/time...
589 CFG_CMD_DHCP * DHCP support
590 CFG_CMD_DIAG * Diagnostics
591 CFG_CMD_DOC * Disk-On-Chip Support
592 CFG_CMD_DTT * Digital Therm and Thermostat
593 CFG_CMD_ECHO * echo arguments
594 CFG_CMD_EEPROM * EEPROM read/write support
595 CFG_CMD_ELF * bootelf, bootvx
597 CFG_CMD_FDC * Floppy Disk Support
598 CFG_CMD_FAT * FAT partition support
599 CFG_CMD_FDOS * Dos diskette Support
600 CFG_CMD_FLASH flinfo, erase, protect
601 CFG_CMD_FPGA FPGA device initialization support
602 CFG_CMD_HWFLOW * RTS/CTS hw flow control
603 CFG_CMD_I2C * I2C serial bus support
604 CFG_CMD_IDE * IDE harddisk support
606 CFG_CMD_IMLS List all found images
607 CFG_CMD_IMMAP * IMMR dump support
608 CFG_CMD_IRQ * irqinfo
609 CFG_CMD_ITEST Integer/string test of 2 values
610 CFG_CMD_JFFS2 * JFFS2 Support
614 CFG_CMD_MEMORY md, mm, nm, mw, cp, cmp, crc, base,
616 CFG_CMD_MISC Misc functions like sleep etc
617 CFG_CMD_MMC * MMC memory mapped support
618 CFG_CMD_MII * MII utility commands
619 CFG_CMD_NAND * NAND support
620 CFG_CMD_NET bootp, tftpboot, rarpboot
621 CFG_CMD_PCI * pciinfo
622 CFG_CMD_PCMCIA * PCMCIA support
623 CFG_CMD_PING * send ICMP ECHO_REQUEST to network host
624 CFG_CMD_PORTIO * Port I/O
625 CFG_CMD_REGINFO * Register dump
626 CFG_CMD_RUN run command in env variable
627 CFG_CMD_SAVES * save S record dump
628 CFG_CMD_SCSI * SCSI Support
629 CFG_CMD_SDRAM * print SDRAM configuration information
630 (requires CFG_CMD_I2C)
631 CFG_CMD_SETGETDCR Support for DCR Register access (4xx only)
632 CFG_CMD_SPI * SPI serial bus support
633 CFG_CMD_USB * USB support
634 CFG_CMD_VFD * VFD support (TRAB)
635 CFG_CMD_BSP * Board SPecific functions
636 CFG_CMD_CDP * Cisco Discover Protocol support
637 -----------------------------------------------
640 CONFIG_CMD_DFL Default configuration; at the moment
641 this is includes all commands, except
642 the ones marked with "*" in the list
645 If you don't define CONFIG_COMMANDS it defaults to
646 CONFIG_CMD_DFL in include/cmd_confdefs.h. A board can
647 override the default settings in the respective
650 EXAMPLE: If you want all functions except of network
651 support you can write:
653 #define CONFIG_COMMANDS (CFG_CMD_ALL & ~CFG_CMD_NET)
656 Note: Don't enable the "icache" and "dcache" commands
657 (configuration option CFG_CMD_CACHE) unless you know
658 what you (and your U-Boot users) are doing. Data
659 cache cannot be enabled on systems like the 8xx or
660 8260 (where accesses to the IMMR region must be
661 uncached), and it cannot be disabled on all other
662 systems where we (mis-) use the data cache to hold an
663 initial stack and some data.
666 XXX - this list needs to get updated!
670 If this variable is defined, it enables watchdog
671 support. There must be support in the platform specific
672 code for a watchdog. For the 8xx and 8260 CPUs, the
673 SIU Watchdog feature is enabled in the SYPCR
677 CONFIG_VERSION_VARIABLE
678 If this variable is defined, an environment variable
679 named "ver" is created by U-Boot showing the U-Boot
680 version as printed by the "version" command.
681 This variable is readonly.
685 When CFG_CMD_DATE is selected, the type of the RTC
686 has to be selected, too. Define exactly one of the
689 CONFIG_RTC_MPC8xx - use internal RTC of MPC8xx
690 CONFIG_RTC_PCF8563 - use Philips PCF8563 RTC
691 CONFIG_RTC_MC146818 - use MC146818 RTC
692 CONFIG_RTC_DS1307 - use Maxim, Inc. DS1307 RTC
693 CONFIG_RTC_DS1337 - use Maxim, Inc. DS1337 RTC
694 CONFIG_RTC_DS1338 - use Maxim, Inc. DS1338 RTC
695 CONFIG_RTC_DS164x - use Dallas DS164x RTC
696 CONFIG_RTC_MAX6900 - use Maxim, Inc. MAX6900 RTC
698 Note that if the RTC uses I2C, then the I2C interface
699 must also be configured. See I2C Support, below.
703 When CONFIG_TIMESTAMP is selected, the timestamp
704 (date and time) of an image is printed by image
705 commands like bootm or iminfo. This option is
706 automatically enabled when you select CFG_CMD_DATE .
709 CONFIG_MAC_PARTITION and/or CONFIG_DOS_PARTITION
710 and/or CONFIG_ISO_PARTITION
712 If IDE or SCSI support is enabled (CFG_CMD_IDE or
713 CFG_CMD_SCSI) you must configure support for at least
714 one partition type as well.
717 CONFIG_IDE_RESET_ROUTINE - this is defined in several
718 board configurations files but used nowhere!
720 CONFIG_IDE_RESET - is this is defined, IDE Reset will
721 be performed by calling the function
722 ide_set_reset(int reset)
723 which has to be defined in a board specific file
728 Set this to enable ATAPI support.
733 Set this to enable support for disks larger than 137GB
734 Also look at CFG_64BIT_LBA ,CFG_64BIT_VSPRINTF and CFG_64BIT_STRTOUL
735 Whithout these , LBA48 support uses 32bit variables and will 'only'
736 support disks up to 2.1TB.
739 When enabled, makes the IDE subsystem use 64bit sector addresses.
743 At the moment only there is only support for the
744 SYM53C8XX SCSI controller; define
745 CONFIG_SCSI_SYM53C8XX to enable it.
747 CFG_SCSI_MAX_LUN [8], CFG_SCSI_MAX_SCSI_ID [7] and
748 CFG_SCSI_MAX_DEVICE [CFG_SCSI_MAX_SCSI_ID *
749 CFG_SCSI_MAX_LUN] can be adjusted to define the
750 maximum numbers of LUNs, SCSI ID's and target
752 CFG_SCSI_SYM53C8XX_CCF to fix clock timing (80Mhz)
754 - NETWORK Support (PCI):
756 Support for Intel 8254x gigabit chips.
759 Support for Intel 82557/82559/82559ER chips.
760 Optional CONFIG_EEPRO100_SROM_WRITE enables eeprom
761 write routine for first time initialisation.
764 Support for Digital 2114x chips.
765 Optional CONFIG_TULIP_SELECT_MEDIA for board specific
766 modem chip initialisation (KS8761/QS6611).
769 Support for National dp83815 chips.
772 Support for National dp8382[01] gigabit chips.
774 - NETWORK Support (other):
776 CONFIG_DRIVER_LAN91C96
777 Support for SMSC's LAN91C96 chips.
780 Define this to hold the physical address
781 of the LAN91C96's I/O space
783 CONFIG_LAN91C96_USE_32_BIT
784 Define this to enable 32 bit addressing
786 CONFIG_DRIVER_SMC91111
787 Support for SMSC's LAN91C111 chip
790 Define this to hold the physical address
791 of the device (I/O space)
793 CONFIG_SMC_USE_32_BIT
794 Define this if data bus is 32 bits
796 CONFIG_SMC_USE_IOFUNCS
797 Define this to use i/o functions instead of macros
798 (some hardware wont work with macros)
801 At the moment only the UHCI host controller is
802 supported (PIP405, MIP405, MPC5200); define
803 CONFIG_USB_UHCI to enable it.
804 define CONFIG_USB_KEYBOARD to enable the USB Keyboard
805 and define CONFIG_USB_STORAGE to enable the USB
808 Supported are USB Keyboards and USB Floppy drives
810 MPC5200 USB requires additional defines:
812 for 528 MHz Clock: 0x0001bbbb
814 for differential drivers: 0x00001000
815 for single ended drivers: 0x00005000
819 The MMC controller on the Intel PXA is supported. To
820 enable this define CONFIG_MMC. The MMC can be
821 accessed from the boot prompt by mapping the device
822 to physical memory similar to flash. Command line is
823 enabled with CFG_CMD_MMC. The MMC driver also works with
824 the FAT fs. This is enabled with CFG_CMD_FAT.
826 - Journaling Flash filesystem support:
827 CONFIG_JFFS2_NAND, CONFIG_JFFS2_NAND_OFF, CONFIG_JFFS2_NAND_SIZE,
828 CONFIG_JFFS2_NAND_DEV
829 Define these for a default partition on a NAND device
831 CFG_JFFS2_FIRST_SECTOR,
832 CFG_JFFS2_FIRST_BANK, CFG_JFFS2_NUM_BANKS
833 Define these for a default partition on a NOR device
836 Define this to create an own partition. You have to provide a
837 function struct part_info* jffs2_part_info(int part_num)
839 If you define only one JFFS2 partition you may also want to
840 #define CFG_JFFS_SINGLE_PART 1
841 to disable the command chpart. This is the default when you
842 have not defined a custom partition
847 Define this to enable standard (PC-Style) keyboard
851 Standard PC keyboard driver with US (is default) and
852 GERMAN key layout (switch via environment 'keymap=de') support.
853 Export function i8042_kbd_init, i8042_tstc and i8042_getc
854 for cfb_console. Supports cursor blinking.
859 Define this to enable video support (for output to
864 Enable Chips & Technologies 69000 Video chip
866 CONFIG_VIDEO_SMI_LYNXEM
867 Enable Silicon Motion SMI 712/710/810 Video chip. The
868 video output is selected via environment 'videoout'
869 (1 = LCD and 2 = CRT). If videoout is undefined, CRT is
872 For the CT69000 and SMI_LYNXEM drivers, videomode is
873 selected via environment 'videomode'. Two diferent ways
875 - "videomode=num" 'num' is a standard LiLo mode numbers.
876 Following standard modes are supported (* is default):
878 Colors 640x480 800x600 1024x768 1152x864 1280x1024
879 -------------+---------------------------------------------
880 8 bits | 0x301* 0x303 0x305 0x161 0x307
881 15 bits | 0x310 0x313 0x316 0x162 0x319
882 16 bits | 0x311 0x314 0x317 0x163 0x31A
883 24 bits | 0x312 0x315 0x318 ? 0x31B
884 -------------+---------------------------------------------
885 (i.e. setenv videomode 317; saveenv; reset;)
887 - "videomode=bootargs" all the video parameters are parsed
888 from the bootargs. (See drivers/videomodes.c)
891 CONFIG_VIDEO_SED13806
892 Enable Epson SED13806 driver. This driver supports 8bpp
893 and 16bpp modes defined by CONFIG_VIDEO_SED13806_8BPP
894 or CONFIG_VIDEO_SED13806_16BPP
899 Define this to enable a custom keyboard support.
900 This simply calls drv_keyboard_init() which must be
901 defined in your board-specific files.
902 The only board using this so far is RBC823.
904 - LCD Support: CONFIG_LCD
906 Define this to enable LCD support (for output to LCD
907 display); also select one of the supported displays
908 by defining one of these:
910 CONFIG_NEC_NL6448AC33:
912 NEC NL6448AC33-18. Active, color, single scan.
914 CONFIG_NEC_NL6448BC20
916 NEC NL6448BC20-08. 6.5", 640x480.
917 Active, color, single scan.
919 CONFIG_NEC_NL6448BC33_54
921 NEC NL6448BC33-54. 10.4", 640x480.
922 Active, color, single scan.
926 Sharp 320x240. Active, color, single scan.
927 It isn't 16x9, and I am not sure what it is.
929 CONFIG_SHARP_LQ64D341
931 Sharp LQ64D341 display, 640x480.
932 Active, color, single scan.
936 HLD1045 display, 640x480.
937 Active, color, single scan.
941 Optrex CBL50840-2 NF-FW 99 22 M5
943 Hitachi LMG6912RPFC-00T
947 320x240. Black & white.
949 Normally display is black on white background; define
950 CFG_WHITE_ON_BLACK to get it inverted.
952 - Splash Screen Support: CONFIG_SPLASH_SCREEN
954 If this option is set, the environment is checked for
955 a variable "splashimage". If found, the usual display
956 of logo, copyright and system information on the LCD
957 is suppressed and the BMP image at the address
958 specified in "splashimage" is loaded instead. The
959 console is redirected to the "nulldev", too. This
960 allows for a "silent" boot where a splash screen is
961 loaded very quickly after power-on.
963 - Gzip compressed BMP image support: CONFIG_VIDEO_BMP_GZIP
965 If this option is set, additionally to standard BMP
966 images, gzipped BMP images can be displayed via the
967 splashscreen support or the bmp command.
969 - Compression support:
972 If this option is set, support for bzip2 compressed
973 images is included. If not, only uncompressed and gzip
974 compressed images are supported.
976 NOTE: the bzip2 algorithm requires a lot of RAM, so
977 the malloc area (as defined by CFG_MALLOC_LEN) should
983 The address of PHY on MII bus.
985 CONFIG_PHY_CLOCK_FREQ (ppc4xx)
987 The clock frequency of the MII bus
991 If this option is set, support for speed/duplex
992 detection of Gigabit PHY is included.
994 CONFIG_PHY_RESET_DELAY
996 Some PHY like Intel LXT971A need extra delay after
997 reset before any MII register access is possible.
998 For such PHY, set this option to the usec delay
999 required. (minimum 300usec for LXT971A)
1001 CONFIG_PHY_CMD_DELAY (ppc4xx)
1003 Some PHY like Intel LXT971A need extra delay after
1004 command issued before MII status register can be read
1011 Define a default value for ethernet address to use
1012 for the respective ethernet interface, in case this
1013 is not determined automatically.
1018 Define a default value for the IP address to use for
1019 the default ethernet interface, in case this is not
1020 determined through e.g. bootp.
1022 - Server IP address:
1025 Defines a default value for theIP address of a TFTP
1026 server to contact when using the "tftboot" command.
1028 - BOOTP Recovery Mode:
1029 CONFIG_BOOTP_RANDOM_DELAY
1031 If you have many targets in a network that try to
1032 boot using BOOTP, you may want to avoid that all
1033 systems send out BOOTP requests at precisely the same
1034 moment (which would happen for instance at recovery
1035 from a power failure, when all systems will try to
1036 boot, thus flooding the BOOTP server. Defining
1037 CONFIG_BOOTP_RANDOM_DELAY causes a random delay to be
1038 inserted before sending out BOOTP requests. The
1039 following delays are insterted then:
1041 1st BOOTP request: delay 0 ... 1 sec
1042 2nd BOOTP request: delay 0 ... 2 sec
1043 3rd BOOTP request: delay 0 ... 4 sec
1045 BOOTP requests: delay 0 ... 8 sec
1047 - DHCP Advanced Options:
1050 You can fine tune the DHCP functionality by adding
1051 these flags to the CONFIG_BOOTP_MASK define:
1053 CONFIG_BOOTP_DNS2 - If a DHCP client requests the DNS
1054 serverip from a DHCP server, it is possible that more
1055 than one DNS serverip is offered to the client.
1056 If CONFIG_BOOTP_DNS2 is enabled, the secondary DNS
1057 serverip will be stored in the additional environment
1058 variable "dnsip2". The first DNS serverip is always
1059 stored in the variable "dnsip", when CONFIG_BOOTP_DNS
1060 is added to the CONFIG_BOOTP_MASK.
1062 CONFIG_BOOTP_SEND_HOSTNAME - Some DHCP servers are capable
1063 to do a dynamic update of a DNS server. To do this, they
1064 need the hostname of the DHCP requester.
1065 If CONFIG_BOOP_SEND_HOSTNAME is added to the
1066 CONFIG_BOOTP_MASK, the content of the "hostname"
1067 environment variable is passed as option 12 to
1071 CONFIG_CDP_DEVICE_ID
1073 The device id used in CDP trigger frames.
1075 CONFIG_CDP_DEVICE_ID_PREFIX
1077 A two character string which is prefixed to the MAC address
1082 A printf format string which contains the ascii name of
1083 the port. Normally is set to "eth%d" which sets
1084 eth0 for the first ethernet, eth1 for the second etc.
1086 CONFIG_CDP_CAPABILITIES
1088 A 32bit integer which indicates the device capabilities;
1089 0x00000010 for a normal host which does not forwards.
1093 An ascii string containing the version of the software.
1097 An ascii string containing the name of the platform.
1101 A 32bit integer sent on the trigger.
1103 CONFIG_CDP_POWER_CONSUMPTION
1105 A 16bit integer containing the power consumption of the
1106 device in .1 of milliwatts.
1108 CONFIG_CDP_APPLIANCE_VLAN_TYPE
1110 A byte containing the id of the VLAN.
1112 - Status LED: CONFIG_STATUS_LED
1114 Several configurations allow to display the current
1115 status using a LED. For instance, the LED will blink
1116 fast while running U-Boot code, stop blinking as
1117 soon as a reply to a BOOTP request was received, and
1118 start blinking slow once the Linux kernel is running
1119 (supported by a status LED driver in the Linux
1120 kernel). Defining CONFIG_STATUS_LED enables this
1123 - CAN Support: CONFIG_CAN_DRIVER
1125 Defining CONFIG_CAN_DRIVER enables CAN driver support
1126 on those systems that support this (optional)
1127 feature, like the TQM8xxL modules.
1129 - I2C Support: CONFIG_HARD_I2C | CONFIG_SOFT_I2C
1131 These enable I2C serial bus commands. Defining either of
1132 (but not both of) CONFIG_HARD_I2C or CONFIG_SOFT_I2C will
1133 include the appropriate I2C driver for the selected cpu.
1135 This will allow you to use i2c commands at the u-boot
1136 command line (as long as you set CFG_CMD_I2C in
1137 CONFIG_COMMANDS) and communicate with i2c based realtime
1138 clock chips. See common/cmd_i2c.c for a description of the
1139 command line interface.
1141 CONFIG_HARD_I2C selects the CPM hardware driver for I2C.
1143 CONFIG_SOFT_I2C configures u-boot to use a software (aka
1144 bit-banging) driver instead of CPM or similar hardware
1147 There are several other quantities that must also be
1148 defined when you define CONFIG_HARD_I2C or CONFIG_SOFT_I2C.
1150 In both cases you will need to define CFG_I2C_SPEED
1151 to be the frequency (in Hz) at which you wish your i2c bus
1152 to run and CFG_I2C_SLAVE to be the address of this node (ie
1153 the cpu's i2c node address).
1155 Now, the u-boot i2c code for the mpc8xx (cpu/mpc8xx/i2c.c)
1156 sets the cpu up as a master node and so its address should
1157 therefore be cleared to 0 (See, eg, MPC823e User's Manual
1158 p.16-473). So, set CFG_I2C_SLAVE to 0.
1160 That's all that's required for CONFIG_HARD_I2C.
1162 If you use the software i2c interface (CONFIG_SOFT_I2C)
1163 then the following macros need to be defined (examples are
1164 from include/configs/lwmon.h):
1168 (Optional). Any commands necessary to enable the I2C
1169 controller or configure ports.
1171 eg: #define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL)
1175 (Only for MPC8260 CPU). The I/O port to use (the code
1176 assumes both bits are on the same port). Valid values
1177 are 0..3 for ports A..D.
1181 The code necessary to make the I2C data line active
1182 (driven). If the data line is open collector, this
1185 eg: #define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA)
1189 The code necessary to make the I2C data line tri-stated
1190 (inactive). If the data line is open collector, this
1193 eg: #define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA)
1197 Code that returns TRUE if the I2C data line is high,
1200 eg: #define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
1204 If <bit> is TRUE, sets the I2C data line high. If it
1205 is FALSE, it clears it (low).
1207 eg: #define I2C_SDA(bit) \
1208 if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \
1209 else immr->im_cpm.cp_pbdat &= ~PB_SDA
1213 If <bit> is TRUE, sets the I2C clock line high. If it
1214 is FALSE, it clears it (low).
1216 eg: #define I2C_SCL(bit) \
1217 if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \
1218 else immr->im_cpm.cp_pbdat &= ~PB_SCL
1222 This delay is invoked four times per clock cycle so this
1223 controls the rate of data transfer. The data rate thus
1224 is 1 / (I2C_DELAY * 4). Often defined to be something
1227 #define I2C_DELAY udelay(2)
1231 When a board is reset during an i2c bus transfer
1232 chips might think that the current transfer is still
1233 in progress. On some boards it is possible to access
1234 the i2c SCLK line directly, either by using the
1235 processor pin as a GPIO or by having a second pin
1236 connected to the bus. If this option is defined a
1237 custom i2c_init_board() routine in boards/xxx/board.c
1238 is run early in the boot sequence.
1240 CONFIG_I2CFAST (PPC405GP|PPC405EP only)
1242 This option enables configuration of bi_iic_fast[] flags
1243 in u-boot bd_info structure based on u-boot environment
1244 variable "i2cfast". (see also i2cfast)
1246 - SPI Support: CONFIG_SPI
1248 Enables SPI driver (so far only tested with
1249 SPI EEPROM, also an instance works with Crystal A/D and
1250 D/As on the SACSng board)
1254 Enables extended (16-bit) SPI EEPROM addressing.
1255 (symmetrical to CONFIG_I2C_X)
1259 Enables a software (bit-bang) SPI driver rather than
1260 using hardware support. This is a general purpose
1261 driver that only requires three general I/O port pins
1262 (two outputs, one input) to function. If this is
1263 defined, the board configuration must define several
1264 SPI configuration items (port pins to use, etc). For
1265 an example, see include/configs/sacsng.h.
1267 - FPGA Support: CONFIG_FPGA_COUNT
1269 Specify the number of FPGA devices to support.
1273 Used to specify the types of FPGA devices. For example,
1274 #define CONFIG_FPGA CFG_XILINX_VIRTEX2
1276 CFG_FPGA_PROG_FEEDBACK
1278 Enable printing of hash marks during FPGA configuration.
1282 Enable checks on FPGA configuration interface busy
1283 status by the configuration function. This option
1284 will require a board or device specific function to
1289 If defined, a function that provides delays in the FPGA
1290 configuration driver.
1292 CFG_FPGA_CHECK_CTRLC
1293 Allow Control-C to interrupt FPGA configuration
1295 CFG_FPGA_CHECK_ERROR
1297 Check for configuration errors during FPGA bitfile
1298 loading. For example, abort during Virtex II
1299 configuration if the INIT_B line goes low (which
1300 indicated a CRC error).
1304 Maximum time to wait for the INIT_B line to deassert
1305 after PROB_B has been deasserted during a Virtex II
1306 FPGA configuration sequence. The default time is 500
1311 Maximum time to wait for BUSY to deassert during
1312 Virtex II FPGA configuration. The default is 5 mS.
1314 CFG_FPGA_WAIT_CONFIG
1316 Time to wait after FPGA configuration. The default is
1319 - Configuration Management:
1322 If defined, this string will be added to the U-Boot
1323 version information (U_BOOT_VERSION)
1325 - Vendor Parameter Protection:
1327 U-Boot considers the values of the environment
1328 variables "serial#" (Board Serial Number) and
1329 "ethaddr" (Ethernet Address) to be parameters that
1330 are set once by the board vendor / manufacturer, and
1331 protects these variables from casual modification by
1332 the user. Once set, these variables are read-only,
1333 and write or delete attempts are rejected. You can
1334 change this behviour:
1336 If CONFIG_ENV_OVERWRITE is #defined in your config
1337 file, the write protection for vendor parameters is
1338 completely disabled. Anybody can change or delete
1341 Alternatively, if you #define _both_ CONFIG_ETHADDR
1342 _and_ CONFIG_OVERWRITE_ETHADDR_ONCE, a default
1343 ethernet address is installed in the environment,
1344 which can be changed exactly ONCE by the user. [The
1345 serial# is unaffected by this, i. e. it remains
1351 Define this variable to enable the reservation of
1352 "protected RAM", i. e. RAM which is not overwritten
1353 by U-Boot. Define CONFIG_PRAM to hold the number of
1354 kB you want to reserve for pRAM. You can overwrite
1355 this default value by defining an environment
1356 variable "pram" to the number of kB you want to
1357 reserve. Note that the board info structure will
1358 still show the full amount of RAM. If pRAM is
1359 reserved, a new environment variable "mem" will
1360 automatically be defined to hold the amount of
1361 remaining RAM in a form that can be passed as boot
1362 argument to Linux, for instance like that:
1364 setenv bootargs ... mem=\$(mem)
1367 This way you can tell Linux not to use this memory,
1368 either, which results in a memory region that will
1369 not be affected by reboots.
1371 *WARNING* If your board configuration uses automatic
1372 detection of the RAM size, you must make sure that
1373 this memory test is non-destructive. So far, the
1374 following board configurations are known to be
1377 ETX094, IVMS8, IVML24, SPD8xx, TQM8xxL,
1378 HERMES, IP860, RPXlite, LWMON, LANTEC,
1379 PCU_E, FLAGADM, TQM8260
1384 Define this variable to stop the system in case of a
1385 fatal error, so that you have to reset it manually.
1386 This is probably NOT a good idea for an embedded
1387 system where you want to system to reboot
1388 automatically as fast as possible, but it may be
1389 useful during development since you can try to debug
1390 the conditions that lead to the situation.
1392 CONFIG_NET_RETRY_COUNT
1394 This variable defines the number of retries for
1395 network operations like ARP, RARP, TFTP, or BOOTP
1396 before giving up the operation. If not defined, a
1397 default value of 5 is used.
1399 - Command Interpreter:
1402 Enable auto completion of commands using TAB.
1406 Define this variable to enable the "hush" shell (from
1407 Busybox) as command line interpreter, thus enabling
1408 powerful command line syntax like
1409 if...then...else...fi conditionals or `&&' and '||'
1410 constructs ("shell scripts").
1412 If undefined, you get the old, much simpler behaviour
1413 with a somewhat smaller memory footprint.
1418 This defines the secondary prompt string, which is
1419 printed when the command interpreter needs more input
1420 to complete a command. Usually "> ".
1424 In the current implementation, the local variables
1425 space and global environment variables space are
1426 separated. Local variables are those you define by
1427 simply typing `name=value'. To access a local
1428 variable later on, you have write `$name' or
1429 `${name}'; to execute the contents of a variable
1430 directly type `$name' at the command prompt.
1432 Global environment variables are those you use
1433 setenv/printenv to work with. To run a command stored
1434 in such a variable, you need to use the run command,
1435 and you must not use the '$' sign to access them.
1437 To store commands and special characters in a
1438 variable, please use double quotation marks
1439 surrounding the whole text of the variable, instead
1440 of the backslashes before semicolons and special
1443 - Default Environment:
1444 CONFIG_EXTRA_ENV_SETTINGS
1446 Define this to contain any number of null terminated
1447 strings (variable = value pairs) that will be part of
1448 the default environment compiled into the boot image.
1450 For example, place something like this in your
1451 board's config file:
1453 #define CONFIG_EXTRA_ENV_SETTINGS \
1457 Warning: This method is based on knowledge about the
1458 internal format how the environment is stored by the
1459 U-Boot code. This is NOT an official, exported
1460 interface! Although it is unlikely that this format
1461 will change soon, there is no guarantee either.
1462 You better know what you are doing here.
1464 Note: overly (ab)use of the default environment is
1465 discouraged. Make sure to check other ways to preset
1466 the environment like the autoscript function or the
1469 - DataFlash Support:
1470 CONFIG_HAS_DATAFLASH
1472 Defining this option enables DataFlash features and
1473 allows to read/write in Dataflash via the standard
1476 - SystemACE Support:
1479 Adding this option adds support for Xilinx SystemACE
1480 chips attached via some sort of local bus. The address
1481 of the chip must alsh be defined in the
1482 CFG_SYSTEMACE_BASE macro. For example:
1484 #define CONFIG_SYSTEMACE
1485 #define CFG_SYSTEMACE_BASE 0xf0000000
1487 When SystemACE support is added, the "ace" device type
1488 becomes available to the fat commands, i.e. fatls.
1490 - TFTP Fixed UDP Port:
1493 If this is defined, the environment variable tftpport
1494 is used to supply the TFTP UDP source port value.
1495 If tftpport isn't defined, the normal pseudo-random port
1496 number generator is used.
1498 The purpose for this is to allow a TFTP server to
1499 blindly start the TFTP transfer using the pre-configured
1500 target IP address and UDP port. This has the effect of
1501 "punching through" the (Windows XP) firewall, allowing
1502 the remainder of the TFTP transfer to proceed normally.
1503 A better solution is to properly configure the firewall,
1504 but sometimes that is not allowed.
1506 - Show boot progress:
1507 CONFIG_SHOW_BOOT_PROGRESS
1509 Defining this option allows to add some board-
1510 specific code (calling a user-provided function
1511 "show_boot_progress(int)") that enables you to show
1512 the system's boot progress on some display (for
1513 example, some LED's) on your board. At the moment,
1514 the following checkpoints are implemented:
1517 1 common/cmd_bootm.c before attempting to boot an image
1518 -1 common/cmd_bootm.c Image header has bad magic number
1519 2 common/cmd_bootm.c Image header has correct magic number
1520 -2 common/cmd_bootm.c Image header has bad checksum
1521 3 common/cmd_bootm.c Image header has correct checksum
1522 -3 common/cmd_bootm.c Image data has bad checksum
1523 4 common/cmd_bootm.c Image data has correct checksum
1524 -4 common/cmd_bootm.c Image is for unsupported architecture
1525 5 common/cmd_bootm.c Architecture check OK
1526 -5 common/cmd_bootm.c Wrong Image Type (not kernel, multi, standalone)
1527 6 common/cmd_bootm.c Image Type check OK
1528 -6 common/cmd_bootm.c gunzip uncompression error
1529 -7 common/cmd_bootm.c Unimplemented compression type
1530 7 common/cmd_bootm.c Uncompression OK
1531 -8 common/cmd_bootm.c Wrong Image Type (not kernel, multi, standalone)
1532 8 common/cmd_bootm.c Image Type check OK
1533 -9 common/cmd_bootm.c Unsupported OS (not Linux, BSD, VxWorks, QNX)
1534 9 common/cmd_bootm.c Start initial ramdisk verification
1535 -10 common/cmd_bootm.c Ramdisk header has bad magic number
1536 -11 common/cmd_bootm.c Ramdisk header has bad checksum
1537 10 common/cmd_bootm.c Ramdisk header is OK
1538 -12 common/cmd_bootm.c Ramdisk data has bad checksum
1539 11 common/cmd_bootm.c Ramdisk data has correct checksum
1540 12 common/cmd_bootm.c Ramdisk verification complete, start loading
1541 -13 common/cmd_bootm.c Wrong Image Type (not PPC Linux Ramdisk)
1542 13 common/cmd_bootm.c Start multifile image verification
1543 14 common/cmd_bootm.c No initial ramdisk, no multifile, continue.
1544 15 common/cmd_bootm.c All preparation done, transferring control to OS
1546 -30 lib_ppc/board.c Fatal error, hang the system
1547 -31 post/post.c POST test failed, detected by post_output_backlog()
1548 -32 post/post.c POST test failed, detected by post_run_single()
1550 -1 common/cmd_doc.c Bad usage of "doc" command
1551 -1 common/cmd_doc.c No boot device
1552 -1 common/cmd_doc.c Unknown Chip ID on boot device
1553 -1 common/cmd_doc.c Read Error on boot device
1554 -1 common/cmd_doc.c Image header has bad magic number
1556 -1 common/cmd_ide.c Bad usage of "ide" command
1557 -1 common/cmd_ide.c No boot device
1558 -1 common/cmd_ide.c Unknown boot device
1559 -1 common/cmd_ide.c Unknown partition table
1560 -1 common/cmd_ide.c Invalid partition type
1561 -1 common/cmd_ide.c Read Error on boot device
1562 -1 common/cmd_ide.c Image header has bad magic number
1564 -1 common/cmd_nand.c Bad usage of "nand" command
1565 -1 common/cmd_nand.c No boot device
1566 -1 common/cmd_nand.c Unknown Chip ID on boot device
1567 -1 common/cmd_nand.c Read Error on boot device
1568 -1 common/cmd_nand.c Image header has bad magic number
1570 -1 common/env_common.c Environment has a bad CRC, using default
1576 [so far only for SMDK2400 and TRAB boards]
1578 - Modem support endable:
1579 CONFIG_MODEM_SUPPORT
1581 - RTS/CTS Flow control enable:
1584 - Modem debug support:
1585 CONFIG_MODEM_SUPPORT_DEBUG
1587 Enables debugging stuff (char screen[1024], dbg())
1588 for modem support. Useful only with BDI2000.
1590 - Interrupt support (PPC):
1592 There are common interrupt_init() and timer_interrupt()
1593 for all PPC archs. interrupt_init() calls interrupt_init_cpu()
1594 for cpu specific initialization. interrupt_init_cpu()
1595 should set decrementer_count to appropriate value. If
1596 cpu resets decrementer automatically after interrupt
1597 (ppc4xx) it should set decrementer_count to zero.
1598 timer_interrupt() calls timer_interrupt_cpu() for cpu
1599 specific handling. If board has watchdog / status_led
1600 / other_activity_monitor it works automatically from
1601 general timer_interrupt().
1605 In the target system modem support is enabled when a
1606 specific key (key combination) is pressed during
1607 power-on. Otherwise U-Boot will boot normally
1608 (autoboot). The key_pressed() fuction is called from
1609 board_init(). Currently key_pressed() is a dummy
1610 function, returning 1 and thus enabling modem
1613 If there are no modem init strings in the
1614 environment, U-Boot proceed to autoboot; the
1615 previous output (banner, info printfs) will be
1618 See also: doc/README.Modem
1621 Configuration Settings:
1622 -----------------------
1624 - CFG_LONGHELP: Defined when you want long help messages included;
1625 undefine this when you're short of memory.
1627 - CFG_PROMPT: This is what U-Boot prints on the console to
1628 prompt for user input.
1630 - CFG_CBSIZE: Buffer size for input from the Console
1632 - CFG_PBSIZE: Buffer size for Console output
1634 - CFG_MAXARGS: max. Number of arguments accepted for monitor commands
1636 - CFG_BARGSIZE: Buffer size for Boot Arguments which are passed to
1637 the application (usually a Linux kernel) when it is
1640 - CFG_BAUDRATE_TABLE:
1641 List of legal baudrate settings for this board.
1643 - CFG_CONSOLE_INFO_QUIET
1644 Suppress display of console information at boot.
1646 - CFG_CONSOLE_IS_IN_ENV
1647 If the board specific function
1648 extern int overwrite_console (void);
1649 returns 1, the stdin, stderr and stdout are switched to the
1650 serial port, else the settings in the environment are used.
1652 - CFG_CONSOLE_OVERWRITE_ROUTINE
1653 Enable the call to overwrite_console().
1655 - CFG_CONSOLE_ENV_OVERWRITE
1656 Enable overwrite of previous console environment settings.
1658 - CFG_MEMTEST_START, CFG_MEMTEST_END:
1659 Begin and End addresses of the area used by the
1663 Enable an alternate, more extensive memory test.
1665 - CFG_MEMTEST_SCRATCH:
1666 Scratch address used by the alternate memory test
1667 You only need to set this if address zero isn't writeable
1669 - CFG_TFTP_LOADADDR:
1670 Default load address for network file downloads
1672 - CFG_LOADS_BAUD_CHANGE:
1673 Enable temporary baudrate change while serial download
1676 Physical start address of SDRAM. _Must_ be 0 here.
1679 Physical start address of Motherboard I/O (if using a
1683 Physical start address of Flash memory.
1686 Physical start address of boot monitor code (set by
1687 make config files to be same as the text base address
1688 (TEXT_BASE) used when linking) - same as
1689 CFG_FLASH_BASE when booting from flash.
1692 Size of memory reserved for monitor code, used to
1693 determine _at_compile_time_ (!) if the environment is
1694 embedded within the U-Boot image, or in a separate
1698 Size of DRAM reserved for malloc() use.
1701 Maximum size of memory mapped by the startup code of
1702 the Linux kernel; all data that must be processed by
1703 the Linux kernel (bd_info, boot arguments, eventually
1704 initrd image) must be put below this limit.
1706 - CFG_MAX_FLASH_BANKS:
1707 Max number of Flash memory banks
1709 - CFG_MAX_FLASH_SECT:
1710 Max number of sectors on a Flash chip
1712 - CFG_FLASH_ERASE_TOUT:
1713 Timeout for Flash erase operations (in ms)
1715 - CFG_FLASH_WRITE_TOUT:
1716 Timeout for Flash write operations (in ms)
1718 - CFG_FLASH_LOCK_TOUT
1719 Timeout for Flash set sector lock bit operation (in ms)
1721 - CFG_FLASH_UNLOCK_TOUT
1722 Timeout for Flash clear lock bits operation (in ms)
1724 - CFG_FLASH_PROTECTION
1725 If defined, hardware flash sectors protection is used
1726 instead of U-Boot software protection.
1728 - CFG_DIRECT_FLASH_TFTP:
1730 Enable TFTP transfers directly to flash memory;
1731 without this option such a download has to be
1732 performed in two steps: (1) download to RAM, and (2)
1733 copy from RAM to flash.
1735 The two-step approach is usually more reliable, since
1736 you can check if the download worked before you erase
1737 the flash, but in some situations (when sytem RAM is
1738 too limited to allow for a tempory copy of the
1739 downloaded image) this option may be very useful.
1742 Define if the flash driver uses extra elements in the
1743 common flash structure for storing flash geometry.
1745 - CFG_FLASH_CFI_DRIVER
1746 This option also enables the building of the cfi_flash driver
1747 in the drivers directory
1749 - CFG_RX_ETH_BUFFER:
1750 Defines the number of ethernet receive buffers. On some
1751 ethernet controllers it is recommended to set this value
1752 to 8 or even higher (EEPRO100 or 405 EMAC), since all
1753 buffers can be full shortly after enabling the interface
1754 on high ethernet traffic.
1755 Defaults to 4 if not defined.
1757 The following definitions that deal with the placement and management
1758 of environment data (variable area); in general, we support the
1759 following configurations:
1761 - CFG_ENV_IS_IN_FLASH:
1763 Define this if the environment is in flash memory.
1765 a) The environment occupies one whole flash sector, which is
1766 "embedded" in the text segment with the U-Boot code. This
1767 happens usually with "bottom boot sector" or "top boot
1768 sector" type flash chips, which have several smaller
1769 sectors at the start or the end. For instance, such a
1770 layout can have sector sizes of 8, 2x4, 16, Nx32 kB. In
1771 such a case you would place the environment in one of the
1772 4 kB sectors - with U-Boot code before and after it. With
1773 "top boot sector" type flash chips, you would put the
1774 environment in one of the last sectors, leaving a gap
1775 between U-Boot and the environment.
1779 Offset of environment data (variable area) to the
1780 beginning of flash memory; for instance, with bottom boot
1781 type flash chips the second sector can be used: the offset
1782 for this sector is given here.
1784 CFG_ENV_OFFSET is used relative to CFG_FLASH_BASE.
1788 This is just another way to specify the start address of
1789 the flash sector containing the environment (instead of
1792 - CFG_ENV_SECT_SIZE:
1794 Size of the sector containing the environment.
1797 b) Sometimes flash chips have few, equal sized, BIG sectors.
1798 In such a case you don't want to spend a whole sector for
1803 If you use this in combination with CFG_ENV_IS_IN_FLASH
1804 and CFG_ENV_SECT_SIZE, you can specify to use only a part
1805 of this flash sector for the environment. This saves
1806 memory for the RAM copy of the environment.
1808 It may also save flash memory if you decide to use this
1809 when your environment is "embedded" within U-Boot code,
1810 since then the remainder of the flash sector could be used
1811 for U-Boot code. It should be pointed out that this is
1812 STRONGLY DISCOURAGED from a robustness point of view:
1813 updating the environment in flash makes it always
1814 necessary to erase the WHOLE sector. If something goes
1815 wrong before the contents has been restored from a copy in
1816 RAM, your target system will be dead.
1818 - CFG_ENV_ADDR_REDUND
1821 These settings describe a second storage area used to hold
1822 a redundand copy of the environment data, so that there is
1823 a valid backup copy in case there is a power failure during
1824 a "saveenv" operation.
1826 BE CAREFUL! Any changes to the flash layout, and some changes to the
1827 source code will make it necessary to adapt <board>/u-boot.lds*
1831 - CFG_ENV_IS_IN_NVRAM:
1833 Define this if you have some non-volatile memory device
1834 (NVRAM, battery buffered SRAM) which you want to use for the
1840 These two #defines are used to determin the memory area you
1841 want to use for environment. It is assumed that this memory
1842 can just be read and written to, without any special
1845 BE CAREFUL! The first access to the environment happens quite early
1846 in U-Boot initalization (when we try to get the setting of for the
1847 console baudrate). You *MUST* have mappend your NVRAM area then, or
1850 Please note that even with NVRAM we still use a copy of the
1851 environment in RAM: we could work on NVRAM directly, but we want to
1852 keep settings there always unmodified except somebody uses "saveenv"
1853 to save the current settings.
1856 - CFG_ENV_IS_IN_EEPROM:
1858 Use this if you have an EEPROM or similar serial access
1859 device and a driver for it.
1864 These two #defines specify the offset and size of the
1865 environment area within the total memory of your EEPROM.
1867 - CFG_I2C_EEPROM_ADDR:
1868 If defined, specified the chip address of the EEPROM device.
1869 The default address is zero.
1871 - CFG_EEPROM_PAGE_WRITE_BITS:
1872 If defined, the number of bits used to address bytes in a
1873 single page in the EEPROM device. A 64 byte page, for example
1874 would require six bits.
1876 - CFG_EEPROM_PAGE_WRITE_DELAY_MS:
1877 If defined, the number of milliseconds to delay between
1878 page writes. The default is zero milliseconds.
1880 - CFG_I2C_EEPROM_ADDR_LEN:
1881 The length in bytes of the EEPROM memory array address. Note
1882 that this is NOT the chip address length!
1884 - CFG_I2C_EEPROM_ADDR_OVERFLOW:
1885 EEPROM chips that implement "address overflow" are ones
1886 like Catalyst 24WC04/08/16 which has 9/10/11 bits of
1887 address and the extra bits end up in the "chip address" bit
1888 slots. This makes a 24WC08 (1Kbyte) chip look like four 256
1891 Note that we consider the length of the address field to
1892 still be one byte because the extra address bits are hidden
1893 in the chip address.
1896 The size in bytes of the EEPROM device.
1899 - CFG_ENV_IS_IN_DATAFLASH:
1901 Define this if you have a DataFlash memory device which you
1902 want to use for the environment.
1908 These three #defines specify the offset and size of the
1909 environment area within the total memory of your DataFlash placed
1910 at the specified address.
1912 - CFG_ENV_IS_IN_NAND:
1914 Define this if you have a NAND device which you want to use
1915 for the environment.
1920 These two #defines specify the offset and size of the environment
1921 area within the first NAND device.
1923 - CFG_SPI_INIT_OFFSET
1925 Defines offset to the initial SPI buffer area in DPRAM. The
1926 area is used at an early stage (ROM part) if the environment
1927 is configured to reside in the SPI EEPROM: We need a 520 byte
1928 scratch DPRAM area. It is used between the two initialization
1929 calls (spi_init_f() and spi_init_r()). A value of 0xB00 seems
1930 to be a good choice since it makes it far enough from the
1931 start of the data area as well as from the stack pointer.
1933 Please note that the environment is read-only as long as the monitor
1934 has been relocated to RAM and a RAM copy of the environment has been
1935 created; also, when using EEPROM you will have to use getenv_r()
1936 until then to read environment variables.
1938 The environment is protected by a CRC32 checksum. Before the monitor
1939 is relocated into RAM, as a result of a bad CRC you will be working
1940 with the compiled-in default environment - *silently*!!! [This is
1941 necessary, because the first environment variable we need is the
1942 "baudrate" setting for the console - if we have a bad CRC, we don't
1943 have any device yet where we could complain.]
1945 Note: once the monitor has been relocated, then it will complain if
1946 the default environment is used; a new CRC is computed as soon as you
1947 use the "saveenv" command to store a valid environment.
1949 - CFG_FAULT_ECHO_LINK_DOWN:
1950 Echo the inverted Ethernet link state to the fault LED.
1952 Note: If this option is active, then CFG_FAULT_MII_ADDR
1953 also needs to be defined.
1955 - CFG_FAULT_MII_ADDR:
1956 MII address of the PHY to check for the Ethernet link state.
1958 - CFG_64BIT_VSPRINTF:
1959 Makes vsprintf (and all *printf functions) support printing
1960 of 64bit values by using the L quantifier
1962 - CFG_64BIT_STRTOUL:
1963 Adds simple_strtoull that returns a 64bit value
1965 Low Level (hardware related) configuration options:
1966 ---------------------------------------------------
1968 - CFG_CACHELINE_SIZE:
1969 Cache Line Size of the CPU.
1972 Default address of the IMMR after system reset.
1974 Needed on some 8260 systems (MPC8260ADS, PQ2FADS-ZU,
1975 and RPXsuper) to be able to adjust the position of
1976 the IMMR register after a reset.
1978 - Floppy Disk Support:
1979 CFG_FDC_DRIVE_NUMBER
1981 the default drive number (default value 0)
1985 defines the spacing between fdc chipset registers
1990 defines the offset of register from address. It
1991 depends on which part of the data bus is connected to
1992 the fdc chipset. (default value 0)
1994 If CFG_ISA_IO_STRIDE CFG_ISA_IO_OFFSET and
1995 CFG_FDC_DRIVE_NUMBER are undefined, they take their
1998 if CFG_FDC_HW_INIT is defined, then the function
1999 fdc_hw_init() is called at the beginning of the FDC
2000 setup. fdc_hw_init() must be provided by the board
2001 source code. It is used to make hardware dependant
2004 - CFG_IMMR: Physical address of the Internal Memory.
2005 DO NOT CHANGE unless you know exactly what you're
2006 doing! (11-4) [MPC8xx/82xx systems only]
2008 - CFG_INIT_RAM_ADDR:
2010 Start address of memory area that can be used for
2011 initial data and stack; please note that this must be
2012 writable memory that is working WITHOUT special
2013 initialization, i. e. you CANNOT use normal RAM which
2014 will become available only after programming the
2015 memory controller and running certain initialization
2018 U-Boot uses the following memory types:
2019 - MPC8xx and MPC8260: IMMR (internal memory of the CPU)
2020 - MPC824X: data cache
2021 - PPC4xx: data cache
2023 - CFG_GBL_DATA_OFFSET:
2025 Offset of the initial data structure in the memory
2026 area defined by CFG_INIT_RAM_ADDR. Usually
2027 CFG_GBL_DATA_OFFSET is chosen such that the initial
2028 data is located at the end of the available space
2029 (sometimes written as (CFG_INIT_RAM_END -
2030 CFG_INIT_DATA_SIZE), and the initial stack is just
2031 below that area (growing from (CFG_INIT_RAM_ADDR +
2032 CFG_GBL_DATA_OFFSET) downward.
2035 On the MPC824X (or other systems that use the data
2036 cache for initial memory) the address chosen for
2037 CFG_INIT_RAM_ADDR is basically arbitrary - it must
2038 point to an otherwise UNUSED address space between
2039 the top of RAM and the start of the PCI space.
2041 - CFG_SIUMCR: SIU Module Configuration (11-6)
2043 - CFG_SYPCR: System Protection Control (11-9)
2045 - CFG_TBSCR: Time Base Status and Control (11-26)
2047 - CFG_PISCR: Periodic Interrupt Status and Control (11-31)
2049 - CFG_PLPRCR: PLL, Low-Power, and Reset Control Register (15-30)
2051 - CFG_SCCR: System Clock and reset Control Register (15-27)
2053 - CFG_OR_TIMING_SDRAM:
2057 periodic timer for refresh
2059 - CFG_DER: Debug Event Register (37-47)
2061 - FLASH_BASE0_PRELIM, FLASH_BASE1_PRELIM, CFG_REMAP_OR_AM,
2062 CFG_PRELIM_OR_AM, CFG_OR_TIMING_FLASH, CFG_OR0_REMAP,
2063 CFG_OR0_PRELIM, CFG_BR0_PRELIM, CFG_OR1_REMAP, CFG_OR1_PRELIM,
2065 Memory Controller Definitions: BR0/1 and OR0/1 (FLASH)
2067 - SDRAM_BASE2_PRELIM, SDRAM_BASE3_PRELIM, SDRAM_MAX_SIZE,
2068 CFG_OR_TIMING_SDRAM, CFG_OR2_PRELIM, CFG_BR2_PRELIM,
2069 CFG_OR3_PRELIM, CFG_BR3_PRELIM:
2070 Memory Controller Definitions: BR2/3 and OR2/3 (SDRAM)
2072 - CFG_MAMR_PTA, CFG_MPTPR_2BK_4K, CFG_MPTPR_1BK_4K, CFG_MPTPR_2BK_8K,
2073 CFG_MPTPR_1BK_8K, CFG_MAMR_8COL, CFG_MAMR_9COL:
2074 Machine Mode Register and Memory Periodic Timer
2075 Prescaler definitions (SDRAM timing)
2077 - CFG_I2C_UCODE_PATCH, CFG_I2C_DPMEM_OFFSET [0x1FC0]:
2078 enable I2C microcode relocation patch (MPC8xx);
2079 define relocation offset in DPRAM [DSP2]
2081 - CFG_SPI_UCODE_PATCH, CFG_SPI_DPMEM_OFFSET [0x1FC0]:
2082 enable SPI microcode relocation patch (MPC8xx);
2083 define relocation offset in DPRAM [SCC4]
2086 Use OSCM clock mode on MBX8xx board. Be careful,
2087 wrong setting might damage your board. Read
2088 doc/README.MBX before setting this variable!
2090 - CFG_CPM_POST_WORD_ADDR: (MPC8xx, MPC8260 only)
2091 Offset of the bootmode word in DPRAM used by post
2092 (Power On Self Tests). This definition overrides
2093 #define'd default value in commproc.h resp.
2096 - CFG_PCI_SLV_MEM_LOCAL, CFG_PCI_SLV_MEM_BUS, CFG_PICMR0_MASK_ATTRIB,
2097 CFG_PCI_MSTR0_LOCAL, CFG_PCIMSK0_MASK, CFG_PCI_MSTR1_LOCAL,
2098 CFG_PCIMSK1_MASK, CFG_PCI_MSTR_MEM_LOCAL, CFG_PCI_MSTR_MEM_BUS,
2099 CFG_CPU_PCI_MEM_START, CFG_PCI_MSTR_MEM_SIZE, CFG_POCMR0_MASK_ATTRIB,
2100 CFG_PCI_MSTR_MEMIO_LOCAL, CFG_PCI_MSTR_MEMIO_BUS, CPU_PCI_MEMIO_START,
2101 CFG_PCI_MSTR_MEMIO_SIZE, CFG_POCMR1_MASK_ATTRIB, CFG_PCI_MSTR_IO_LOCAL,
2102 CFG_PCI_MSTR_IO_BUS, CFG_CPU_PCI_IO_START, CFG_PCI_MSTR_IO_SIZE,
2103 CFG_POCMR2_MASK_ATTRIB: (MPC826x only)
2104 Overrides the default PCI memory map in cpu/mpc8260/pci.c if set.
2106 - CONFIG_ETHER_ON_FEC[12]
2107 Define to enable FEC[12] on a 8xx series processor.
2109 - CONFIG_FEC[12]_PHY
2110 Define to the hardcoded PHY address which corresponds
2111 to the given FEC; i. e.
2112 #define CONFIG_FEC1_PHY 4
2113 means that the PHY with address 4 is connected to FEC1
2115 When set to -1, means to probe for first available.
2117 - CONFIG_FEC[12]_PHY_NORXERR
2118 The PHY does not have a RXERR line (RMII only).
2119 (so program the FEC to ignore it).
2122 Enable RMII mode for all FECs.
2123 Note that this is a global option, we can't
2124 have one FEC in standard MII mode and another in RMII mode.
2126 - CONFIG_CRC32_VERIFY
2127 Add a verify option to the crc32 command.
2130 => crc32 -v <address> <count> <crc32>
2132 Where address/count indicate a memory area
2133 and crc32 is the correct crc32 which the
2137 Add the "loopw" memory command. This only takes effect if
2138 the memory commands are activated globally (CFG_CMD_MEM).
2141 Add the "mdc" and "mwc" memory commands. These are cyclic
2146 This command will print 4 bytes (10,11,12,13) each 500 ms.
2148 => mwc.l 100 12345678 10
2149 This command will write 12345678 to address 100 all 10 ms.
2151 This only takes effect if the memory commands are activated
2152 globally (CFG_CMD_MEM).
2154 - CONFIG_SKIP_LOWLEVEL_INIT
2155 - CONFIG_SKIP_RELOCATE_UBOOT
2157 [ARM only] If these variables are defined, then
2158 certain low level initializations (like setting up
2159 the memory controller) are omitted and/or U-Boot does
2160 not relocate itself into RAM.
2161 Normally these variables MUST NOT be defined. The
2162 only exception is when U-Boot is loaded (to RAM) by
2163 some other boot loader or by a debugger which
2164 performs these intializations itself.
2167 Building the Software:
2168 ======================
2170 Building U-Boot has been tested in native PPC environments (on a
2171 PowerBook G3 running LinuxPPC 2000) and in cross environments
2172 (running RedHat 6.x and 7.x Linux on x86, Solaris 2.6 on a SPARC, and
2175 If you are not using a native PPC environment, it is assumed that you
2176 have the GNU cross compiling tools available in your path and named
2177 with a prefix of "powerpc-linux-". If this is not the case, (e.g. if
2178 you are using Monta Vista's Hard Hat Linux CDK 1.2) you must change
2179 the definition of CROSS_COMPILE in Makefile. For HHL on a 4xx CPU,
2182 CROSS_COMPILE = ppc_4xx-
2185 U-Boot is intended to be simple to build. After installing the
2186 sources you must configure U-Boot for one specific board type. This
2191 where "NAME_config" is the name of one of the existing
2192 configurations; the following names are supported:
2194 ADCIOP_config FPS860L_config omap730p2_config
2195 ADS860_config GEN860T_config pcu_e_config
2197 AR405_config GENIETV_config PIP405_config
2198 at91rm9200dk_config GTH_config QS823_config
2199 CANBT_config hermes_config QS850_config
2200 cmi_mpc5xx_config hymod_config QS860T_config
2201 cogent_common_config IP860_config RPXlite_config
2202 cogent_mpc8260_config IVML24_config RPXlite_DW_config
2203 cogent_mpc8xx_config IVMS8_config RPXsuper_config
2204 CPCI405_config JSE_config rsdproto_config
2205 CPCIISER4_config LANTEC_config Sandpoint8240_config
2206 csb272_config lwmon_config sbc8260_config
2207 CU824_config MBX860T_config sbc8560_33_config
2208 DUET_ADS_config MBX_config sbc8560_66_config
2209 EBONY_config MPC8260ADS_config SM850_config
2210 ELPT860_config MPC8540ADS_config SPD823TS_config
2211 ESTEEM192E_config MPC8540EVAL_config stxgp3_config
2212 ETX094_config MPC8560ADS_config SXNI855T_config
2213 FADS823_config NETVIA_config TQM823L_config
2214 FADS850SAR_config omap1510inn_config TQM850L_config
2215 FADS860T_config omap1610h2_config TQM855L_config
2216 FPS850L_config omap1610inn_config TQM860L_config
2217 omap5912osk_config walnut_config
2218 omap2420h4_config Yukon8220_config
2221 Note: for some board special configuration names may exist; check if
2222 additional information is available from the board vendor; for
2223 instance, the TQM823L systems are available without (standard)
2224 or with LCD support. You can select such additional "features"
2225 when chosing the configuration, i. e.
2228 - will configure for a plain TQM823L, i. e. no LCD support
2230 make TQM823L_LCD_config
2231 - will configure for a TQM823L with U-Boot console on LCD
2236 Finally, type "make all", and you should get some working U-Boot
2237 images ready for download to / installation on your system:
2239 - "u-boot.bin" is a raw binary image
2240 - "u-boot" is an image in ELF binary format
2241 - "u-boot.srec" is in Motorola S-Record format
2244 Please be aware that the Makefiles assume you are using GNU make, so
2245 for instance on NetBSD you might need to use "gmake" instead of
2249 If the system board that you have is not listed, then you will need
2250 to port U-Boot to your hardware platform. To do this, follow these
2253 1. Add a new configuration option for your board to the toplevel
2254 "Makefile" and to the "MAKEALL" script, using the existing
2255 entries as examples. Note that here and at many other places
2256 boards and other names are listed in alphabetical sort order. Please
2258 2. Create a new directory to hold your board specific code. Add any
2259 files you need. In your board directory, you will need at least
2260 the "Makefile", a "<board>.c", "flash.c" and "u-boot.lds".
2261 3. Create a new configuration file "include/configs/<board>.h" for
2263 3. If you're porting U-Boot to a new CPU, then also create a new
2264 directory to hold your CPU specific code. Add any files you need.
2265 4. Run "make <board>_config" with your new name.
2266 5. Type "make", and you should get a working "u-boot.srec" file
2267 to be installed on your target system.
2268 6. Debug and solve any problems that might arise.
2269 [Of course, this last step is much harder than it sounds.]
2272 Testing of U-Boot Modifications, Ports to New Hardware, etc.:
2273 ==============================================================
2275 If you have modified U-Boot sources (for instance added a new board
2276 or support for new devices, a new CPU, etc.) you are expected to
2277 provide feedback to the other developers. The feedback normally takes
2278 the form of a "patch", i. e. a context diff against a certain (latest
2279 official or latest in CVS) version of U-Boot sources.
2281 But before you submit such a patch, please verify that your modifi-
2282 cation did not break existing code. At least make sure that *ALL* of
2283 the supported boards compile WITHOUT ANY compiler warnings. To do so,
2284 just run the "MAKEALL" script, which will configure and build U-Boot
2285 for ALL supported system. Be warned, this will take a while. You can
2286 select which (cross) compiler to use by passing a `CROSS_COMPILE'
2287 environment variable to the script, i. e. to use the cross tools from
2288 MontaVista's Hard Hat Linux you can type
2290 CROSS_COMPILE=ppc_8xx- MAKEALL
2292 or to build on a native PowerPC system you can type
2294 CROSS_COMPILE=' ' MAKEALL
2296 See also "U-Boot Porting Guide" below.
2299 Monitor Commands - Overview:
2300 ============================
2302 go - start application at address 'addr'
2303 run - run commands in an environment variable
2304 bootm - boot application image from memory
2305 bootp - boot image via network using BootP/TFTP protocol
2306 tftpboot- boot image via network using TFTP protocol
2307 and env variables "ipaddr" and "serverip"
2308 (and eventually "gatewayip")
2309 rarpboot- boot image via network using RARP/TFTP protocol
2310 diskboot- boot from IDE devicebootd - boot default, i.e., run 'bootcmd'
2311 loads - load S-Record file over serial line
2312 loadb - load binary file over serial line (kermit mode)
2314 mm - memory modify (auto-incrementing)
2315 nm - memory modify (constant address)
2316 mw - memory write (fill)
2318 cmp - memory compare
2319 crc32 - checksum calculation
2320 imd - i2c memory display
2321 imm - i2c memory modify (auto-incrementing)
2322 inm - i2c memory modify (constant address)
2323 imw - i2c memory write (fill)
2324 icrc32 - i2c checksum calculation
2325 iprobe - probe to discover valid I2C chip addresses
2326 iloop - infinite loop on address range
2327 isdram - print SDRAM configuration information
2328 sspi - SPI utility commands
2329 base - print or set address offset
2330 printenv- print environment variables
2331 setenv - set environment variables
2332 saveenv - save environment variables to persistent storage
2333 protect - enable or disable FLASH write protection
2334 erase - erase FLASH memory
2335 flinfo - print FLASH memory information
2336 bdinfo - print Board Info structure
2337 iminfo - print header information for application image
2338 coninfo - print console devices and informations
2339 ide - IDE sub-system
2340 loop - infinite loop on address range
2341 loopw - infinite write loop on address range
2342 mtest - simple RAM test
2343 icache - enable or disable instruction cache
2344 dcache - enable or disable data cache
2345 reset - Perform RESET of the CPU
2346 echo - echo args to console
2347 version - print monitor version
2348 help - print online help
2349 ? - alias for 'help'
2352 Monitor Commands - Detailed Description:
2353 ========================================
2357 For now: just type "help <command>".
2360 Environment Variables:
2361 ======================
2363 U-Boot supports user configuration using Environment Variables which
2364 can be made persistent by saving to Flash memory.
2366 Environment Variables are set using "setenv", printed using
2367 "printenv", and saved to Flash using "saveenv". Using "setenv"
2368 without a value can be used to delete a variable from the
2369 environment. As long as you don't save the environment you are
2370 working with an in-memory copy. In case the Flash area containing the
2371 environment is erased by accident, a default environment is provided.
2373 Some configuration options can be set using Environment Variables:
2375 baudrate - see CONFIG_BAUDRATE
2377 bootdelay - see CONFIG_BOOTDELAY
2379 bootcmd - see CONFIG_BOOTCOMMAND
2381 bootargs - Boot arguments when booting an RTOS image
2383 bootfile - Name of the image to load with TFTP
2385 autoload - if set to "no" (any string beginning with 'n'),
2386 "bootp" will just load perform a lookup of the
2387 configuration from the BOOTP server, but not try to
2388 load any image using TFTP
2390 autostart - if set to "yes", an image loaded using the "bootp",
2391 "rarpboot", "tftpboot" or "diskboot" commands will
2392 be automatically started (by internally calling
2395 If set to "no", a standalone image passed to the
2396 "bootm" command will be copied to the load address
2397 (and eventually uncompressed), but NOT be started.
2398 This can be used to load and uncompress arbitrary
2401 i2cfast - (PPC405GP|PPC405EP only)
2402 if set to 'y' configures Linux I2C driver for fast
2403 mode (400kHZ). This environment variable is used in
2404 initialization code. So, for changes to be effective
2405 it must be saved and board must be reset.
2407 initrd_high - restrict positioning of initrd images:
2408 If this variable is not set, initrd images will be
2409 copied to the highest possible address in RAM; this
2410 is usually what you want since it allows for
2411 maximum initrd size. If for some reason you want to
2412 make sure that the initrd image is loaded below the
2413 CFG_BOOTMAPSZ limit, you can set this environment
2414 variable to a value of "no" or "off" or "0".
2415 Alternatively, you can set it to a maximum upper
2416 address to use (U-Boot will still check that it
2417 does not overwrite the U-Boot stack and data).
2419 For instance, when you have a system with 16 MB
2420 RAM, and want to reserve 4 MB from use by Linux,
2421 you can do this by adding "mem=12M" to the value of
2422 the "bootargs" variable. However, now you must make
2423 sure that the initrd image is placed in the first
2424 12 MB as well - this can be done with
2426 setenv initrd_high 00c00000
2428 If you set initrd_high to 0xFFFFFFFF, this is an
2429 indication to U-Boot that all addresses are legal
2430 for the Linux kernel, including addresses in flash
2431 memory. In this case U-Boot will NOT COPY the
2432 ramdisk at all. This may be useful to reduce the
2433 boot time on your system, but requires that this
2434 feature is supported by your Linux kernel.
2436 ipaddr - IP address; needed for tftpboot command
2438 loadaddr - Default load address for commands like "bootp",
2439 "rarpboot", "tftpboot", "loadb" or "diskboot"
2441 loads_echo - see CONFIG_LOADS_ECHO
2443 serverip - TFTP server IP address; needed for tftpboot command
2445 bootretry - see CONFIG_BOOT_RETRY_TIME
2447 bootdelaykey - see CONFIG_AUTOBOOT_DELAY_STR
2449 bootstopkey - see CONFIG_AUTOBOOT_STOP_STR
2451 ethprime - When CONFIG_NET_MULTI is enabled controls which
2452 interface is used first.
2454 ethact - When CONFIG_NET_MULTI is enabled controls which
2455 interface is currently active. For example you
2456 can do the following
2458 => setenv ethact FEC ETHERNET
2459 => ping 192.168.0.1 # traffic sent on FEC ETHERNET
2460 => setenv ethact SCC ETHERNET
2461 => ping 10.0.0.1 # traffic sent on SCC ETHERNET
2463 netretry - When set to "no" each network operation will
2464 either succeed or fail without retrying.
2465 When set to "once" the network operation will
2466 fail when all the available network interfaces
2467 are tried once without success.
2468 Useful on scripts which control the retry operation
2471 tftpport - If this is set, the value is used for TFTP's
2474 vlan - When set to a value < 4095 the traffic over
2475 ethernet is encapsulated/received over 802.1q
2478 The following environment variables may be used and automatically
2479 updated by the network boot commands ("bootp" and "rarpboot"),
2480 depending the information provided by your boot server:
2482 bootfile - see above
2483 dnsip - IP address of your Domain Name Server
2484 dnsip2 - IP address of your secondary Domain Name Server
2485 gatewayip - IP address of the Gateway (Router) to use
2486 hostname - Target hostname
2488 netmask - Subnet Mask
2489 rootpath - Pathname of the root filesystem on the NFS server
2490 serverip - see above
2493 There are two special Environment Variables:
2495 serial# - contains hardware identification information such
2496 as type string and/or serial number
2497 ethaddr - Ethernet address
2499 These variables can be set only once (usually during manufacturing of
2500 the board). U-Boot refuses to delete or overwrite these variables
2501 once they have been set once.
2504 Further special Environment Variables:
2506 ver - Contains the U-Boot version string as printed
2507 with the "version" command. This variable is
2508 readonly (see CONFIG_VERSION_VARIABLE).
2511 Please note that changes to some configuration parameters may take
2512 only effect after the next boot (yes, that's just like Windoze :-).
2515 Command Line Parsing:
2516 =====================
2518 There are two different command line parsers available with U-Boot:
2519 the old "simple" one, and the much more powerful "hush" shell:
2521 Old, simple command line parser:
2522 --------------------------------
2524 - supports environment variables (through setenv / saveenv commands)
2525 - several commands on one line, separated by ';'
2526 - variable substitution using "... $(name) ..." syntax
2527 - special characters ('$', ';') can be escaped by prefixing with '\',
2529 setenv bootcmd bootm \$(address)
2530 - You can also escape text by enclosing in single apostrophes, for example:
2531 setenv addip 'setenv bootargs $bootargs ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off'
2536 - similar to Bourne shell, with control structures like
2537 if...then...else...fi, for...do...done; while...do...done,
2538 until...do...done, ...
2539 - supports environment ("global") variables (through setenv / saveenv
2540 commands) and local shell variables (through standard shell syntax
2541 "name=value"); only environment variables can be used with "run"
2547 (1) If a command line (or an environment variable executed by a "run"
2548 command) contains several commands separated by semicolon, and
2549 one of these commands fails, then the remaining commands will be
2552 (2) If you execute several variables with one call to run (i. e.
2553 calling run with a list af variables as arguments), any failing
2554 command will cause "run" to terminate, i. e. the remaining
2555 variables are not executed.
2557 Note for Redundant Ethernet Interfaces:
2558 =======================================
2560 Some boards come with redundant ethernet interfaces; U-Boot supports
2561 such configurations and is capable of automatic selection of a
2562 "working" interface when needed. MAC assignment works as follows:
2564 Network interfaces are numbered eth0, eth1, eth2, ... Corresponding
2565 MAC addresses can be stored in the environment as "ethaddr" (=>eth0),
2566 "eth1addr" (=>eth1), "eth2addr", ...
2568 If the network interface stores some valid MAC address (for instance
2569 in SROM), this is used as default address if there is NO correspon-
2570 ding setting in the environment; if the corresponding environment
2571 variable is set, this overrides the settings in the card; that means:
2573 o If the SROM has a valid MAC address, and there is no address in the
2574 environment, the SROM's address is used.
2576 o If there is no valid address in the SROM, and a definition in the
2577 environment exists, then the value from the environment variable is
2580 o If both the SROM and the environment contain a MAC address, and
2581 both addresses are the same, this MAC address is used.
2583 o If both the SROM and the environment contain a MAC address, and the
2584 addresses differ, the value from the environment is used and a
2587 o If neither SROM nor the environment contain a MAC address, an error
2594 The "boot" commands of this monitor operate on "image" files which
2595 can be basicly anything, preceeded by a special header; see the
2596 definitions in include/image.h for details; basicly, the header
2597 defines the following image properties:
2599 * Target Operating System (Provisions for OpenBSD, NetBSD, FreeBSD,
2600 4.4BSD, Linux, SVR4, Esix, Solaris, Irix, SCO, Dell, NCR, VxWorks,
2601 LynxOS, pSOS, QNX, RTEMS, ARTOS;
2602 Currently supported: Linux, NetBSD, VxWorks, QNX, RTEMS, ARTOS, LynxOS).
2603 * Target CPU Architecture (Provisions for Alpha, ARM, Intel x86,
2604 IA64, MIPS, NIOS, PowerPC, IBM S390, SuperH, Sparc, Sparc 64 Bit;
2605 Currently supported: ARM, Intel x86, MIPS, NIOS, PowerPC).
2606 * Compression Type (uncompressed, gzip, bzip2)
2612 The header is marked by a special Magic Number, and both the header
2613 and the data portions of the image are secured against corruption by
2620 Although U-Boot should support any OS or standalone application
2621 easily, the main focus has always been on Linux during the design of
2624 U-Boot includes many features that so far have been part of some
2625 special "boot loader" code within the Linux kernel. Also, any
2626 "initrd" images to be used are no longer part of one big Linux image;
2627 instead, kernel and "initrd" are separate images. This implementation
2628 serves several purposes:
2630 - the same features can be used for other OS or standalone
2631 applications (for instance: using compressed images to reduce the
2632 Flash memory footprint)
2634 - it becomes much easier to port new Linux kernel versions because
2635 lots of low-level, hardware dependent stuff are done by U-Boot
2637 - the same Linux kernel image can now be used with different "initrd"
2638 images; of course this also means that different kernel images can
2639 be run with the same "initrd". This makes testing easier (you don't
2640 have to build a new "zImage.initrd" Linux image when you just
2641 change a file in your "initrd"). Also, a field-upgrade of the
2642 software is easier now.
2648 Porting Linux to U-Boot based systems:
2649 ---------------------------------------
2651 U-Boot cannot save you from doing all the necessary modifications to
2652 configure the Linux device drivers for use with your target hardware
2653 (no, we don't intend to provide a full virtual machine interface to
2656 But now you can ignore ALL boot loader code (in arch/ppc/mbxboot).
2658 Just make sure your machine specific header file (for instance
2659 include/asm-ppc/tqm8xx.h) includes the same definition of the Board
2660 Information structure as we define in include/u-boot.h, and make
2661 sure that your definition of IMAP_ADDR uses the same value as your
2662 U-Boot configuration in CFG_IMMR.
2665 Configuring the Linux kernel:
2666 -----------------------------
2668 No specific requirements for U-Boot. Make sure you have some root
2669 device (initial ramdisk, NFS) for your target system.
2672 Building a Linux Image:
2673 -----------------------
2675 With U-Boot, "normal" build targets like "zImage" or "bzImage" are
2676 not used. If you use recent kernel source, a new build target
2677 "uImage" will exist which automatically builds an image usable by
2678 U-Boot. Most older kernels also have support for a "pImage" target,
2679 which was introduced for our predecessor project PPCBoot and uses a
2680 100% compatible format.
2689 The "uImage" build target uses a special tool (in 'tools/mkimage') to
2690 encapsulate a compressed Linux kernel image with header information,
2691 CRC32 checksum etc. for use with U-Boot. This is what we are doing:
2693 * build a standard "vmlinux" kernel image (in ELF binary format):
2695 * convert the kernel into a raw binary image:
2697 ${CROSS_COMPILE}-objcopy -O binary \
2698 -R .note -R .comment \
2699 -S vmlinux linux.bin
2701 * compress the binary image:
2705 * package compressed binary image for U-Boot:
2707 mkimage -A ppc -O linux -T kernel -C gzip \
2708 -a 0 -e 0 -n "Linux Kernel Image" \
2709 -d linux.bin.gz uImage
2712 The "mkimage" tool can also be used to create ramdisk images for use
2713 with U-Boot, either separated from the Linux kernel image, or
2714 combined into one file. "mkimage" encapsulates the images with a 64
2715 byte header containing information about target architecture,
2716 operating system, image type, compression method, entry points, time
2717 stamp, CRC32 checksums, etc.
2719 "mkimage" can be called in two ways: to verify existing images and
2720 print the header information, or to build new images.
2722 In the first form (with "-l" option) mkimage lists the information
2723 contained in the header of an existing U-Boot image; this includes
2724 checksum verification:
2726 tools/mkimage -l image
2727 -l ==> list image header information
2729 The second form (with "-d" option) is used to build a U-Boot image
2730 from a "data file" which is used as image payload:
2732 tools/mkimage -A arch -O os -T type -C comp -a addr -e ep \
2733 -n name -d data_file image
2734 -A ==> set architecture to 'arch'
2735 -O ==> set operating system to 'os'
2736 -T ==> set image type to 'type'
2737 -C ==> set compression type 'comp'
2738 -a ==> set load address to 'addr' (hex)
2739 -e ==> set entry point to 'ep' (hex)
2740 -n ==> set image name to 'name'
2741 -d ==> use image data from 'datafile'
2743 Right now, all Linux kernels for PowerPC systems use the same load
2744 address (0x00000000), but the entry point address depends on the
2747 - 2.2.x kernels have the entry point at 0x0000000C,
2748 - 2.3.x and later kernels have the entry point at 0x00000000.
2750 So a typical call to build a U-Boot image would read:
2752 -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
2753 > -A ppc -O linux -T kernel -C gzip -a 0 -e 0 \
2754 > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux.gz \
2755 > examples/uImage.TQM850L
2756 Image Name: 2.4.4 kernel for TQM850L
2757 Created: Wed Jul 19 02:34:59 2000
2758 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2759 Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
2760 Load Address: 0x00000000
2761 Entry Point: 0x00000000
2763 To verify the contents of the image (or check for corruption):
2765 -> tools/mkimage -l examples/uImage.TQM850L
2766 Image Name: 2.4.4 kernel for TQM850L
2767 Created: Wed Jul 19 02:34:59 2000
2768 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2769 Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
2770 Load Address: 0x00000000
2771 Entry Point: 0x00000000
2773 NOTE: for embedded systems where boot time is critical you can trade
2774 speed for memory and install an UNCOMPRESSED image instead: this
2775 needs more space in Flash, but boots much faster since it does not
2776 need to be uncompressed:
2778 -> gunzip /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux.gz
2779 -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
2780 > -A ppc -O linux -T kernel -C none -a 0 -e 0 \
2781 > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux \
2782 > examples/uImage.TQM850L-uncompressed
2783 Image Name: 2.4.4 kernel for TQM850L
2784 Created: Wed Jul 19 02:34:59 2000
2785 Image Type: PowerPC Linux Kernel Image (uncompressed)
2786 Data Size: 792160 Bytes = 773.59 kB = 0.76 MB
2787 Load Address: 0x00000000
2788 Entry Point: 0x00000000
2791 Similar you can build U-Boot images from a 'ramdisk.image.gz' file
2792 when your kernel is intended to use an initial ramdisk:
2794 -> tools/mkimage -n 'Simple Ramdisk Image' \
2795 > -A ppc -O linux -T ramdisk -C gzip \
2796 > -d /LinuxPPC/images/SIMPLE-ramdisk.image.gz examples/simple-initrd
2797 Image Name: Simple Ramdisk Image
2798 Created: Wed Jan 12 14:01:50 2000
2799 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
2800 Data Size: 566530 Bytes = 553.25 kB = 0.54 MB
2801 Load Address: 0x00000000
2802 Entry Point: 0x00000000
2805 Installing a Linux Image:
2806 -------------------------
2808 To downloading a U-Boot image over the serial (console) interface,
2809 you must convert the image to S-Record format:
2811 objcopy -I binary -O srec examples/image examples/image.srec
2813 The 'objcopy' does not understand the information in the U-Boot
2814 image header, so the resulting S-Record file will be relative to
2815 address 0x00000000. To load it to a given address, you need to
2816 specify the target address as 'offset' parameter with the 'loads'
2819 Example: install the image to address 0x40100000 (which on the
2820 TQM8xxL is in the first Flash bank):
2822 => erase 40100000 401FFFFF
2828 ## Ready for S-Record download ...
2829 ~>examples/image.srec
2830 1 2 3 4 5 6 7 8 9 10 11 12 13 ...
2832 15989 15990 15991 15992
2833 [file transfer complete]
2835 ## Start Addr = 0x00000000
2838 You can check the success of the download using the 'iminfo' command;
2839 this includes a checksum verification so you can be sure no data
2840 corruption happened:
2844 ## Checking Image at 40100000 ...
2845 Image Name: 2.2.13 for initrd on TQM850L
2846 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2847 Data Size: 335725 Bytes = 327 kB = 0 MB
2848 Load Address: 00000000
2849 Entry Point: 0000000c
2850 Verifying Checksum ... OK
2856 The "bootm" command is used to boot an application that is stored in
2857 memory (RAM or Flash). In case of a Linux kernel image, the contents
2858 of the "bootargs" environment variable is passed to the kernel as
2859 parameters. You can check and modify this variable using the
2860 "printenv" and "setenv" commands:
2863 => printenv bootargs
2864 bootargs=root=/dev/ram
2866 => setenv bootargs root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
2868 => printenv bootargs
2869 bootargs=root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
2872 ## Booting Linux kernel at 40020000 ...
2873 Image Name: 2.2.13 for NFS on TQM850L
2874 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2875 Data Size: 381681 Bytes = 372 kB = 0 MB
2876 Load Address: 00000000
2877 Entry Point: 0000000c
2878 Verifying Checksum ... OK
2879 Uncompressing Kernel Image ... OK
2880 Linux version 2.2.13 (
[email protected]) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:35:17 MEST 2000
2881 Boot arguments: root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
2882 time_init: decrementer frequency = 187500000/60
2883 Calibrating delay loop... 49.77 BogoMIPS
2884 Memory: 15208k available (700k kernel code, 444k data, 32k init) [c0000000,c1000000]
2887 If you want to boot a Linux kernel with initial ram disk, you pass
2888 the memory addresses of both the kernel and the initrd image (PPBCOOT
2889 format!) to the "bootm" command:
2891 => imi 40100000 40200000
2893 ## Checking Image at 40100000 ...
2894 Image Name: 2.2.13 for initrd on TQM850L
2895 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2896 Data Size: 335725 Bytes = 327 kB = 0 MB
2897 Load Address: 00000000
2898 Entry Point: 0000000c
2899 Verifying Checksum ... OK
2901 ## Checking Image at 40200000 ...
2902 Image Name: Simple Ramdisk Image
2903 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
2904 Data Size: 566530 Bytes = 553 kB = 0 MB
2905 Load Address: 00000000
2906 Entry Point: 00000000
2907 Verifying Checksum ... OK
2909 => bootm 40100000 40200000
2910 ## Booting Linux kernel at 40100000 ...
2911 Image Name: 2.2.13 for initrd on TQM850L
2912 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2913 Data Size: 335725 Bytes = 327 kB = 0 MB
2914 Load Address: 00000000
2915 Entry Point: 0000000c
2916 Verifying Checksum ... OK
2917 Uncompressing Kernel Image ... OK
2918 ## Loading RAMDisk Image at 40200000 ...
2919 Image Name: Simple Ramdisk Image
2920 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
2921 Data Size: 566530 Bytes = 553 kB = 0 MB
2922 Load Address: 00000000
2923 Entry Point: 00000000
2924 Verifying Checksum ... OK
2925 Loading Ramdisk ... OK
2926 Linux version 2.2.13 (
[email protected]) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:32:08 MEST 2000
2927 Boot arguments: root=/dev/ram
2928 time_init: decrementer frequency = 187500000/60
2929 Calibrating delay loop... 49.77 BogoMIPS
2931 RAMDISK: Compressed image found at block 0
2932 VFS: Mounted root (ext2 filesystem).
2936 More About U-Boot Image Types:
2937 ------------------------------
2939 U-Boot supports the following image types:
2941 "Standalone Programs" are directly runnable in the environment
2942 provided by U-Boot; it is expected that (if they behave
2943 well) you can continue to work in U-Boot after return from
2944 the Standalone Program.
2945 "OS Kernel Images" are usually images of some Embedded OS which
2946 will take over control completely. Usually these programs
2947 will install their own set of exception handlers, device
2948 drivers, set up the MMU, etc. - this means, that you cannot
2949 expect to re-enter U-Boot except by resetting the CPU.
2950 "RAMDisk Images" are more or less just data blocks, and their
2951 parameters (address, size) are passed to an OS kernel that is
2953 "Multi-File Images" contain several images, typically an OS
2954 (Linux) kernel image and one or more data images like
2955 RAMDisks. This construct is useful for instance when you want
2956 to boot over the network using BOOTP etc., where the boot
2957 server provides just a single image file, but you want to get
2958 for instance an OS kernel and a RAMDisk image.
2960 "Multi-File Images" start with a list of image sizes, each
2961 image size (in bytes) specified by an "uint32_t" in network
2962 byte order. This list is terminated by an "(uint32_t)0".
2963 Immediately after the terminating 0 follow the images, one by
2964 one, all aligned on "uint32_t" boundaries (size rounded up to
2965 a multiple of 4 bytes).
2967 "Firmware Images" are binary images containing firmware (like
2968 U-Boot or FPGA images) which usually will be programmed to
2971 "Script files" are command sequences that will be executed by
2972 U-Boot's command interpreter; this feature is especially
2973 useful when you configure U-Boot to use a real shell (hush)
2974 as command interpreter.
2980 One of the features of U-Boot is that you can dynamically load and
2981 run "standalone" applications, which can use some resources of
2982 U-Boot like console I/O functions or interrupt services.
2984 Two simple examples are included with the sources:
2989 'examples/hello_world.c' contains a small "Hello World" Demo
2990 application; it is automatically compiled when you build U-Boot.
2991 It's configured to run at address 0x00040004, so you can play with it
2995 ## Ready for S-Record download ...
2996 ~>examples/hello_world.srec
2997 1 2 3 4 5 6 7 8 9 10 11 ...
2998 [file transfer complete]
3000 ## Start Addr = 0x00040004
3002 => go 40004 Hello World! This is a test.
3003 ## Starting application at 0x00040004 ...
3014 Hit any key to exit ...
3016 ## Application terminated, rc = 0x0
3018 Another example, which demonstrates how to register a CPM interrupt
3019 handler with the U-Boot code, can be found in 'examples/timer.c'.
3020 Here, a CPM timer is set up to generate an interrupt every second.
3021 The interrupt service routine is trivial, just printing a '.'
3022 character, but this is just a demo program. The application can be
3023 controlled by the following keys:
3025 ? - print current values og the CPM Timer registers
3026 b - enable interrupts and start timer
3027 e - stop timer and disable interrupts
3028 q - quit application
3031 ## Ready for S-Record download ...
3032 ~>examples/timer.srec
3033 1 2 3 4 5 6 7 8 9 10 11 ...
3034 [file transfer complete]
3036 ## Start Addr = 0x00040004
3039 ## Starting application at 0x00040004 ...
3042 tgcr @ 0xfff00980, tmr @ 0xfff00990, trr @ 0xfff00994, tcr @ 0xfff00998, tcn @ 0xfff0099c, ter @ 0xfff009b0
3045 [q, b, e, ?] Set interval 1000000 us
3048 [q, b, e, ?] ........
3049 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0xef6, ter=0x0
3052 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x2ad4, ter=0x0
3055 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x1efc, ter=0x0
3058 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x169d, ter=0x0
3060 [q, b, e, ?] ...Stopping timer
3062 [q, b, e, ?] ## Application terminated, rc = 0x0
3068 Over time, many people have reported problems when trying to use the
3069 "minicom" terminal emulation program for serial download. I (wd)
3070 consider minicom to be broken, and recommend not to use it. Under
3071 Unix, I recommend to use C-Kermit for general purpose use (and
3072 especially for kermit binary protocol download ("loadb" command), and
3073 use "cu" for S-Record download ("loads" command).
3075 Nevertheless, if you absolutely want to use it try adding this
3076 configuration to your "File transfer protocols" section:
3078 Name Program Name U/D FullScr IO-Red. Multi
3079 X kermit /usr/bin/kermit -i -l %l -s Y U Y N N
3080 Y kermit /usr/bin/kermit -i -l %l -r N D Y N N
3086 Starting at version 0.9.2, U-Boot supports NetBSD both as host
3087 (build U-Boot) and target system (boots NetBSD/mpc8xx).
3089 Building requires a cross environment; it is known to work on
3090 NetBSD/i386 with the cross-powerpc-netbsd-1.3 package (you will also
3091 need gmake since the Makefiles are not compatible with BSD make).
3092 Note that the cross-powerpc package does not install include files;
3093 attempting to build U-Boot will fail because <machine/ansi.h> is
3094 missing. This file has to be installed and patched manually:
3096 # cd /usr/pkg/cross/powerpc-netbsd/include
3098 # ln -s powerpc machine
3099 # cp /usr/src/sys/arch/powerpc/include/ansi.h powerpc/ansi.h
3100 # ${EDIT} powerpc/ansi.h ## must remove __va_list, _BSD_VA_LIST
3102 Native builds *don't* work due to incompatibilities between native
3103 and U-Boot include files.
3105 Booting assumes that (the first part of) the image booted is a
3106 stage-2 loader which in turn loads and then invokes the kernel
3107 proper. Loader sources will eventually appear in the NetBSD source
3108 tree (probably in sys/arc/mpc8xx/stand/u-boot_stage2/); in the
3109 meantime, see ftp://ftp.denx.de/pub/u-boot/ppcboot_stage2.tar.gz
3112 Implementation Internals:
3113 =========================
3115 The following is not intended to be a complete description of every
3116 implementation detail. However, it should help to understand the
3117 inner workings of U-Boot and make it easier to port it to custom
3121 Initial Stack, Global Data:
3122 ---------------------------
3124 The implementation of U-Boot is complicated by the fact that U-Boot
3125 starts running out of ROM (flash memory), usually without access to
3126 system RAM (because the memory controller is not initialized yet).
3127 This means that we don't have writable Data or BSS segments, and BSS
3128 is not initialized as zero. To be able to get a C environment working
3129 at all, we have to allocate at least a minimal stack. Implementation
3130 options for this are defined and restricted by the CPU used: Some CPU
3131 models provide on-chip memory (like the IMMR area on MPC8xx and
3132 MPC826x processors), on others (parts of) the data cache can be
3133 locked as (mis-) used as memory, etc.
3135 Chris Hallinan posted a good summary of these issues to the
3136 u-boot-users mailing list:
3138 Subject: RE: [U-Boot-Users] RE: More On Memory Bank x (nothingness)?
3140 Date: Mon, 10 Feb 2003 16:43:46 -0500 (22:43 MET)
3143 Correct me if I'm wrong, folks, but the way I understand it
3144 is this: Using DCACHE as initial RAM for Stack, etc, does not
3145 require any physical RAM backing up the cache. The cleverness
3146 is that the cache is being used as a temporary supply of
3147 necessary storage before the SDRAM controller is setup. It's
3148 beyond the scope of this list to expain the details, but you
3149 can see how this works by studying the cache architecture and
3150 operation in the architecture and processor-specific manuals.
3152 OCM is On Chip Memory, which I believe the 405GP has 4K. It
3153 is another option for the system designer to use as an
3154 initial stack/ram area prior to SDRAM being available. Either
3155 option should work for you. Using CS 4 should be fine if your
3156 board designers haven't used it for something that would
3157 cause you grief during the initial boot! It is frequently not
3160 CFG_INIT_RAM_ADDR should be somewhere that won't interfere
3161 with your processor/board/system design. The default value
3162 you will find in any recent u-boot distribution in
3163 walnut.h should work for you. I'd set it to a value larger
3164 than your SDRAM module. If you have a 64MB SDRAM module, set
3165 it above 400_0000. Just make sure your board has no resources
3166 that are supposed to respond to that address! That code in
3167 start.S has been around a while and should work as is when
3168 you get the config right.
3173 It is essential to remember this, since it has some impact on the C
3174 code for the initialization procedures:
3176 * Initialized global data (data segment) is read-only. Do not attempt
3179 * Do not use any unitialized global data (or implicitely initialized
3180 as zero data - BSS segment) at all - this is undefined, initiali-
3181 zation is performed later (when relocating to RAM).
3183 * Stack space is very limited. Avoid big data buffers or things like
3186 Having only the stack as writable memory limits means we cannot use
3187 normal global data to share information beween the code. But it
3188 turned out that the implementation of U-Boot can be greatly
3189 simplified by making a global data structure (gd_t) available to all
3190 functions. We could pass a pointer to this data as argument to _all_
3191 functions, but this would bloat the code. Instead we use a feature of
3192 the GCC compiler (Global Register Variables) to share the data: we
3193 place a pointer (gd) to the global data into a register which we
3194 reserve for this purpose.
3196 When choosing a register for such a purpose we are restricted by the
3197 relevant (E)ABI specifications for the current architecture, and by
3198 GCC's implementation.
3200 For PowerPC, the following registers have specific use:
3203 R3-R4: parameter passing and return values
3204 R5-R10: parameter passing
3205 R13: small data area pointer
3209 (U-Boot also uses R14 as internal GOT pointer.)
3211 ==> U-Boot will use R29 to hold a pointer to the global data
3213 Note: on PPC, we could use a static initializer (since the
3214 address of the global data structure is known at compile time),
3215 but it turned out that reserving a register results in somewhat
3216 smaller code - although the code savings are not that big (on
3217 average for all boards 752 bytes for the whole U-Boot image,
3218 624 text + 127 data).
3220 On ARM, the following registers are used:
3222 R0: function argument word/integer result
3223 R1-R3: function argument word
3225 R10: stack limit (used only if stack checking if enabled)
3226 R11: argument (frame) pointer
3227 R12: temporary workspace
3230 R15: program counter
3232 ==> U-Boot will use R8 to hold a pointer to the global data
3238 U-Boot runs in system state and uses physical addresses, i.e. the
3239 MMU is not used either for address mapping nor for memory protection.
3241 The available memory is mapped to fixed addresses using the memory
3242 controller. In this process, a contiguous block is formed for each
3243 memory type (Flash, SDRAM, SRAM), even when it consists of several
3244 physical memory banks.
3246 U-Boot is installed in the first 128 kB of the first Flash bank (on
3247 TQM8xxL modules this is the range 0x40000000 ... 0x4001FFFF). After
3248 booting and sizing and initializing DRAM, the code relocates itself
3249 to the upper end of DRAM. Immediately below the U-Boot code some
3250 memory is reserved for use by malloc() [see CFG_MALLOC_LEN
3251 configuration setting]. Below that, a structure with global Board
3252 Info data is placed, followed by the stack (growing downward).
3254 Additionally, some exception handler code is copied to the low 8 kB
3255 of DRAM (0x00000000 ... 0x00001FFF).
3257 So a typical memory configuration with 16 MB of DRAM could look like
3260 0x0000 0000 Exception Vector code
3263 0x0000 2000 Free for Application Use
3269 0x00FB FF20 Monitor Stack (Growing downward)
3270 0x00FB FFAC Board Info Data and permanent copy of global data
3271 0x00FC 0000 Malloc Arena
3274 0x00FE 0000 RAM Copy of Monitor Code
3275 ... eventually: LCD or video framebuffer
3276 ... eventually: pRAM (Protected RAM - unchanged by reset)
3277 0x00FF FFFF [End of RAM]
3280 System Initialization:
3281 ----------------------
3283 In the reset configuration, U-Boot starts at the reset entry point
3284 (on most PowerPC systens at address 0x00000100). Because of the reset
3285 configuration for CS0# this is a mirror of the onboard Flash memory.
3286 To be able to re-map memory U-Boot then jumps to its link address.
3287 To be able to implement the initialization code in C, a (small!)
3288 initial stack is set up in the internal Dual Ported RAM (in case CPUs
3289 which provide such a feature like MPC8xx or MPC8260), or in a locked
3290 part of the data cache. After that, U-Boot initializes the CPU core,
3291 the caches and the SIU.
3293 Next, all (potentially) available memory banks are mapped using a
3294 preliminary mapping. For example, we put them on 512 MB boundaries
3295 (multiples of 0x20000000: SDRAM on 0x00000000 and 0x20000000, Flash
3296 on 0x40000000 and 0x60000000, SRAM on 0x80000000). Then UPM A is
3297 programmed for SDRAM access. Using the temporary configuration, a
3298 simple memory test is run that determines the size of the SDRAM
3301 When there is more than one SDRAM bank, and the banks are of
3302 different size, the largest is mapped first. For equal size, the first
3303 bank (CS2#) is mapped first. The first mapping is always for address
3304 0x00000000, with any additional banks following immediately to create
3305 contiguous memory starting from 0.
3307 Then, the monitor installs itself at the upper end of the SDRAM area
3308 and allocates memory for use by malloc() and for the global Board
3309 Info data; also, the exception vector code is copied to the low RAM
3310 pages, and the final stack is set up.
3312 Only after this relocation will you have a "normal" C environment;
3313 until that you are restricted in several ways, mostly because you are
3314 running from ROM, and because the code will have to be relocated to a
3318 U-Boot Porting Guide:
3319 ----------------------
3321 [Based on messages by Jerry Van Baren in the U-Boot-Users mailing
3325 int main (int argc, char *argv[])
3327 sighandler_t no_more_time;
3329 signal (SIGALRM, no_more_time);
3330 alarm (PROJECT_DEADLINE - toSec (3 * WEEK));
3332 if (available_money > available_manpower) {
3333 pay consultant to port U-Boot;
3337 Download latest U-Boot source;
3339 Subscribe to u-boot-users mailing list;
3342 email ("Hi, I am new to U-Boot, how do I get started?");
3346 Read the README file in the top level directory;
3347 Read http://www.denx.de/twiki/bin/view/DULG/Manual ;
3348 Read the source, Luke;
3351 if (available_money > toLocalCurrency ($2500)) {
3354 Add a lot of aggravation and time;
3357 Create your own board support subdirectory;
3359 Create your own board config file;
3363 Add / modify source code;
3367 email ("Hi, I am having problems...");
3369 Send patch file to Wolfgang;
3374 void no_more_time (int sig)
3383 All contributions to U-Boot should conform to the Linux kernel
3384 coding style; see the file "Documentation/CodingStyle" in your Linux
3385 kernel source directory.
3387 Please note that U-Boot is implemented in C (and to some small parts
3388 in Assembler); no C++ is used, so please do not use C++ style
3389 comments (//) in your code.
3391 Please also stick to the following formatting rules:
3392 - remove any trailing white space
3393 - use TAB characters for indentation, not spaces
3394 - make sure NOT to use DOS '\r\n' line feeds
3395 - do not add more than 2 empty lines to source files
3396 - do not add trailing empty lines to source files
3398 Submissions which do not conform to the standards may be returned
3399 with a request to reformat the changes.
3405 Since the number of patches for U-Boot is growing, we need to
3406 establish some rules. Submissions which do not conform to these rules
3407 may be rejected, even when they contain important and valuable stuff.
3409 Patches shall be sent to the u-boot-users mailing list.
3411 When you send a patch, please include the following information with
3414 * For bug fixes: a description of the bug and how your patch fixes
3415 this bug. Please try to include a way of demonstrating that the
3416 patch actually fixes something.
3418 * For new features: a description of the feature and your
3421 * A CHANGELOG entry as plaintext (separate from the patch)
3423 * For major contributions, your entry to the CREDITS file
3425 * When you add support for a new board, don't forget to add this
3426 board to the MAKEALL script, too.
3428 * If your patch adds new configuration options, don't forget to
3429 document these in the README file.
3431 * The patch itself. If you are accessing the CVS repository use "cvs
3432 update; cvs diff -puRN"; else, use "diff -purN OLD NEW". If your
3433 version of diff does not support these options, then get the latest
3434 version of GNU diff.
3436 The current directory when running this command shall be the top
3437 level directory of the U-Boot source tree, or it's parent directory
3438 (i. e. please make sure that your patch includes sufficient
3439 directory information for the affected files).
3441 We accept patches as plain text, MIME attachments or as uuencoded
3444 * If one logical set of modifications affects or creates several
3445 files, all these changes shall be submitted in a SINGLE patch file.
3447 * Changesets that contain different, unrelated modifications shall be
3448 submitted as SEPARATE patches, one patch per changeset.
3453 * Before sending the patch, run the MAKEALL script on your patched
3454 source tree and make sure that no errors or warnings are reported
3455 for any of the boards.
3457 * Keep your modifications to the necessary minimum: A patch
3458 containing several unrelated changes or arbitrary reformats will be
3459 returned with a request to re-formatting / split it.
3461 * If you modify existing code, make sure that your new code does not
3462 add to the memory footprint of the code ;-) Small is beautiful!
3463 When adding new features, these should compile conditionally only
3464 (using #ifdef), and the resulting code with the new feature
3465 disabled must not need more memory than the old code without your
3468 * Remember that there is a size limit of 40 kB per message on the
3469 u-boot-users mailing list. Compression may help.
projects / J-u-boot.git / blob