include/configs/rut.h

   1 /*
   2  * siemens rut
   3  * (C) Copyright 2013 Siemens Schweiz AG
   4  * (C) Heiko Schocher, DENX Software Engineering, [email protected].
   5  *
   6  * Based on:
   7  * U-Boot file:/include/configs/am335x_evm.h
   8  *
   9  * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
  10  *
  11  * SPDX-License-Identifier:     GPL-2.0+
  12  */
  13
  14 #ifndef __CONFIG_RUT_H
  15 #define __CONFIG_RUT_H
  16
  17 #define CONFIG_SIEMENS_RUT
  18 #define MACH_TYPE_RUT                   4316
  19 #define CONFIG_SIEMENS_MACH_TYPE        MACH_TYPE_RUT
  20
  21 #include "siemens-am33x-common.h"
  22
  23 #define CONFIG_SYS_MPUCLK       600
  24 #define RUT_IOCTRL_VAL  0x18b
  25 #define DDR_PLL_FREQ    303
  26
  27  /* Physical Memory Map */
  28 #define CONFIG_MAX_RAM_BANK_SIZE        (256 << 20) /* 256 MiB */
  29
  30 /* I2C Configuration */
  31 #define CONFIG_SYS_I2C_SPEED            100000
  32
  33 #define CONFIG_SYS_I2C_EEPROM_ADDR              0x50
  34 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN          2
  35 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS       6       /* 64 byte pages */
  36 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   10      /* take up to 10 msec */
  37
  38 #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS      0x200
  39
  40 #undef CONFIG_SPL_NET_SUPPORT
  41 #undef CONFIG_SPL_NET_VCI_STRING
  42 #undef CONFIG_SPL_ETH_SUPPORT
  43
  44 #define CONFIG_PHY_NATSEMI
  45
  46 #define CONFIG_FACTORYSET
  47
  48
  49 /* Watchdog */
  50 #define WATCHDOG_TRIGGER_GPIO   14
  51
  52 #ifndef CONFIG_SPL_BUILD
  53
  54 /* Use common default */
  55 #define MTDPARTS_DEFAULT        MTDPARTS_DEFAULT_V1
  56
  57 /* Default env settings */
  58 #define CONFIG_EXTRA_ENV_SETTINGS \
  59         "hostname=rut\0" \
  60         "nand_img_size=0x500000\0" \
  61         "splashpos=m,m\0" \
  62         "optargs=fixrtc --no-log consoleblank=0 \0" \
  63         CONFIG_ENV_SETTINGS_V1 \
  64         CONFIG_ENV_SETTINGS_NAND_V1 \
  65         "mmc_dev=0\0" \
  66         "mmc_root=/dev/mmcblk0p2 rw\0" \
  67         "mmc_root_fs_type=ext4 rootwait\0" \
  68         "mmc_load_uimage=" \
  69                 "mmc rescan; " \
  70                 "setenv bootfile uImage;" \
  71                 "fatload mmc ${mmc_dev} ${kloadaddr} ${bootfile}\0" \
  72         "loadbootenv=fatload mmc ${mmc_dev} ${loadaddr} ${bootenv}\0" \
  73         "importbootenv=echo Importing environment from mmc ...; " \
  74                 "env import -t $loadaddr $filesize\0" \
  75         "mmc_args=run bootargs_defaults;" \
  76                 "mtdparts default;" \
  77                 "setenv bootargs ${bootargs} " \
  78                 "root=${mmc_root} ${mtdparts}" \
  79                 "rootfstype=${mmc_root_fs_type} ip=${ip_method} " \
  80                 "eth=${ethaddr} " \
  81                 "\0" \
  82         "mmc_boot=run mmc_args; " \
  83                 "run mmc_load_uimage; " \
  84                 "bootm ${kloadaddr}\0" \
  85         ""
  86
  87 #ifndef CONFIG_RESTORE_FLASH
  88 /* set to negative value for no autoboot */
  89 #define CONFIG_BOOTDELAY                3
  90
  91 #define CONFIG_BOOTCOMMAND \
  92         "if mmc rescan; then " \
  93                 "echo SD/MMC found on device ${mmc_dev};" \
  94                 "if run loadbootenv; then " \
  95                         "echo Loaded environment from ${bootenv};" \
  96                         "run importbootenv;" \
  97                 "fi;" \
  98                 "if test -n $uenvcmd; then " \
  99                         "echo Running uenvcmd ...;" \
 100                         "run uenvcmd;" \
 101                 "fi;" \
 102                 "if run mmc_load_uimage; then " \
 103                         "run mmc_args;" \
 104                         "bootm ${kloadaddr};" \
 105                 "fi;" \
 106         "fi;" \
 107         "run nand_boot;" \
 108         "reset;"
 109
 110 #else
 111 #define CONFIG_BOOTDELAY                0
 112
 113 #define CONFIG_BOOTCOMMAND                      \
 114         "setenv autoload no; "                  \
 115         "dhcp; "                                \
 116         "if tftp 80000000 debrick.scr; then "   \
 117                 "source 80000000; "             \
 118         "fi"
 119 #endif
 120
 121 #endif /* CONFIG_SPL_BUILD */
 122
 123 #ifdef CONFIG_SPL_BUILD
 124 #undef CONFIG_HW_WATCHDOG
 125 #endif
 126
 127 #define CONFIG_VIDEO
 128 #if defined(CONFIG_VIDEO)
 129 #define CONFIG_VIDEO_DA8XX
 130 #define CONFIG_CFB_CONSOLE
 131 #define CONFIG_VGA_AS_SINGLE_DEVICE
 132 #define CONFIG_SPLASH_SCREEN
 133 #define CONFIG_SPLASH_SCREEN_ALIGN
 134 #define CONFIG_VIDEO_LOGO
 135 #define CONFIG_VIDEO_BMP_RLE8
 136 #define CONFIG_VIDEO_BMP_LOGO
 137 #define CONFIG_CMD_BMP
 138 #define DA8XX_LCD_CNTL_BASE     LCD_CNTL_BASE
 139
 140 #define CONFIG_SPI
 141 #define CONFIG_OMAP3_SPI
 142
 143 #define BOARD_LCD_RESET         115     /* Bank 3 pin 19 */
 144 #define CONFIG_ARCH_EARLY_INIT_R
 145 #define CONFIG_FORMIKE
 146 #define DISPL_PLL_SPREAD_SPECTRUM
 147 #define CONFIG_SYS_CONSOLE_BG_COL       0xff
 148 #define CONFIG_SYS_CONSOLE_FG_COL       0x00
 149 #endif
 150
 151 #ifndef CONFIG_SPL_BUILD
 152 #define CONFIG_FIT
 153 #endif
 154
 155 #endif  /* ! __CONFIG_RUT_H */