board/wandboard/wandboard.c

   1 /*
   2  * Copyright (C) 2013 Freescale Semiconductor, Inc.
   3  * Copyright (C) 2014 O.S. Systems Software LTDA.
   4  *
   5  * Author: Fabio Estevam <[email protected]>
   6  *
   7  * SPDX-License-Identifier:     GPL-2.0+
   8  */
   9
  10 #include <asm/arch/clock.h>
  11 #include <asm/arch/crm_regs.h>
  12 #include <asm/arch/iomux.h>
  13 #include <asm/arch/imx-regs.h>
  14 #include <asm/arch/mx6-pins.h>
  15 #include <asm/arch/mxc_hdmi.h>
  16 #include <asm/arch/sys_proto.h>
  17 #include <asm/gpio.h>
  18 #include <asm/imx-common/iomux-v3.h>
  19 #include <asm/imx-common/mxc_i2c.h>
  20 #include <asm/imx-common/boot_mode.h>
  21 #include <asm/imx-common/video.h>
  22 #include <asm/io.h>
  23 #include <linux/sizes.h>
  24 #include <common.h>
  25 #include <fsl_esdhc.h>
  26 #include <mmc.h>
  27 #include <miiphy.h>
  28 #include <netdev.h>
  29 #include <phy.h>
  30 #include <input.h>
  31 #include <i2c.h>
  32
  33 DECLARE_GLOBAL_DATA_PTR;
  34
  35 #define UART_PAD_CTRL  (PAD_CTL_PUS_100K_UP |                   \
  36         PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm |                 \
  37         PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
  38
  39 #define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP |                    \
  40         PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm |                 \
  41         PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
  42
  43 #define ENET_PAD_CTRL  (PAD_CTL_PUS_100K_UP |                   \
  44         PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
  45
  46 #define I2C_PAD_CTRL    (PAD_CTL_PUS_100K_UP |                  \
  47         PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS |   \
  48         PAD_CTL_ODE | PAD_CTL_SRE_FAST)
  49
  50 #define USDHC1_CD_GPIO          IMX_GPIO_NR(1, 2)
  51 #define USDHC3_CD_GPIO          IMX_GPIO_NR(3, 9)
  52 #define ETH_PHY_RESET           IMX_GPIO_NR(3, 29)
  53
  54 int dram_init(void)
  55 {
  56         gd->ram_size = (phys_size_t)CONFIG_DDR_MB * 1024 * 1024;
  57
  58         return 0;
  59 }
  60
  61 static iomux_v3_cfg_t const uart1_pads[] = {
  62         MX6_PAD_CSI0_DAT10__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
  63         MX6_PAD_CSI0_DAT11__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
  64 };
  65
  66 static iomux_v3_cfg_t const usdhc1_pads[] = {
  67         MX6_PAD_SD1_CLK__SD1_CLK   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  68         MX6_PAD_SD1_CMD__SD1_CMD   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  69         MX6_PAD_SD1_DAT0__SD1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  70         MX6_PAD_SD1_DAT1__SD1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  71         MX6_PAD_SD1_DAT2__SD1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  72         MX6_PAD_SD1_DAT3__SD1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  73         /* Carrier MicroSD Card Detect */
  74         MX6_PAD_GPIO_2__GPIO1_IO02      | MUX_PAD_CTRL(NO_PAD_CTRL),
  75 };
  76
  77 static iomux_v3_cfg_t const usdhc3_pads[] = {
  78         MX6_PAD_SD3_CLK__SD3_CLK   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  79         MX6_PAD_SD3_CMD__SD3_CMD   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  80         MX6_PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  81         MX6_PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  82         MX6_PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  83         MX6_PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  84         /* SOM MicroSD Card Detect */
  85         MX6_PAD_EIM_DA9__GPIO3_IO09     | MUX_PAD_CTRL(NO_PAD_CTRL),
  86 };
  87
  88 static iomux_v3_cfg_t const enet_pads[] = {
  89         MX6_PAD_ENET_MDIO__ENET_MDIO            | MUX_PAD_CTRL(ENET_PAD_CTRL),
  90         MX6_PAD_ENET_MDC__ENET_MDC              | MUX_PAD_CTRL(ENET_PAD_CTRL),
  91         MX6_PAD_RGMII_TXC__RGMII_TXC    | MUX_PAD_CTRL(ENET_PAD_CTRL),
  92         MX6_PAD_RGMII_TD0__RGMII_TD0    | MUX_PAD_CTRL(ENET_PAD_CTRL),
  93         MX6_PAD_RGMII_TD1__RGMII_TD1    | MUX_PAD_CTRL(ENET_PAD_CTRL),
  94         MX6_PAD_RGMII_TD2__RGMII_TD2    | MUX_PAD_CTRL(ENET_PAD_CTRL),
  95         MX6_PAD_RGMII_TD3__RGMII_TD3    | MUX_PAD_CTRL(ENET_PAD_CTRL),
  96         MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL      | MUX_PAD_CTRL(ENET_PAD_CTRL),
  97         MX6_PAD_ENET_REF_CLK__ENET_TX_CLK       | MUX_PAD_CTRL(ENET_PAD_CTRL),
  98         MX6_PAD_RGMII_RXC__RGMII_RXC    | MUX_PAD_CTRL(ENET_PAD_CTRL),
  99         MX6_PAD_RGMII_RD0__RGMII_RD0    | MUX_PAD_CTRL(ENET_PAD_CTRL),
 100         MX6_PAD_RGMII_RD1__RGMII_RD1    | MUX_PAD_CTRL(ENET_PAD_CTRL),
 101         MX6_PAD_RGMII_RD2__RGMII_RD2    | MUX_PAD_CTRL(ENET_PAD_CTRL),
 102         MX6_PAD_RGMII_RD3__RGMII_RD3    | MUX_PAD_CTRL(ENET_PAD_CTRL),
 103         MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL      | MUX_PAD_CTRL(ENET_PAD_CTRL),
 104         /* AR8031 PHY Reset */
 105         MX6_PAD_EIM_D29__GPIO3_IO29             | MUX_PAD_CTRL(NO_PAD_CTRL),
 106 };
 107
 108 static void setup_iomux_uart(void)
 109 {
 110         imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
 111 }
 112
 113 static void setup_iomux_enet(void)
 114 {
 115         imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
 116
 117         /* Reset AR8031 PHY */
 118         gpio_direction_output(ETH_PHY_RESET, 0);
 119         udelay(500);
 120         gpio_set_value(ETH_PHY_RESET, 1);
 121 }
 122
 123 static struct fsl_esdhc_cfg usdhc_cfg[2] = {
 124         {USDHC3_BASE_ADDR},
 125         {USDHC1_BASE_ADDR},
 126 };
 127
 128 int board_mmc_getcd(struct mmc *mmc)
 129 {
 130         struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
 131         int ret = 0;
 132
 133         switch (cfg->esdhc_base) {
 134         case USDHC1_BASE_ADDR:
 135                 ret = !gpio_get_value(USDHC1_CD_GPIO);
 136                 break;
 137         case USDHC3_BASE_ADDR:
 138                 ret = !gpio_get_value(USDHC3_CD_GPIO);
 139                 break;
 140         }
 141
 142         return ret;
 143 }
 144
 145 int board_mmc_init(bd_t *bis)
 146 {
 147         int ret;
 148         u32 index = 0;
 149
 150         /*
 151          * Following map is done:
 152          * (U-boot device node)    (Physical Port)
 153          * mmc0                    SOM MicroSD
 154          * mmc1                    Carrier board MicroSD
 155          */
 156         for (index = 0; index < CONFIG_SYS_FSL_USDHC_NUM; ++index) {
 157                 switch (index) {
 158                 case 0:
 159                         imx_iomux_v3_setup_multiple_pads(
 160                                 usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
 161                         usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
 162                         usdhc_cfg[0].max_bus_width = 4;
 163                         gpio_direction_input(USDHC3_CD_GPIO);
 164                         break;
 165                 case 1:
 166                         imx_iomux_v3_setup_multiple_pads(
 167                                 usdhc1_pads, ARRAY_SIZE(usdhc1_pads));
 168                         usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
 169                         usdhc_cfg[1].max_bus_width = 4;
 170                         gpio_direction_input(USDHC1_CD_GPIO);
 171                         break;
 172                 default:
 173                         printf("Warning: you configured more USDHC controllers"
 174                                "(%d) then supported by the board (%d)\n",
 175                                index + 1, CONFIG_SYS_FSL_USDHC_NUM);
 176                         return -EINVAL;
 177                 }
 178
 179                 ret = fsl_esdhc_initialize(bis, &usdhc_cfg[index]);
 180                 if (ret)
 181                         return ret;
 182         }
 183
 184         return 0;
 185 }
 186
 187 static int mx6_rgmii_rework(struct phy_device *phydev)
 188 {
 189         unsigned short val;
 190
 191         /* To enable AR8031 ouput a 125MHz clk from CLK_25M */
 192         phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7);
 193         phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016);
 194         phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007);
 195
 196         val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe);
 197         val &= 0xffe3;
 198         val |= 0x18;
 199         phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val);
 200
 201         /* introduce tx clock delay */
 202         phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x5);
 203         val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e);
 204         val |= 0x0100;
 205         phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, val);
 206
 207         return 0;
 208 }
 209
 210 int board_phy_config(struct phy_device *phydev)
 211 {
 212         mx6_rgmii_rework(phydev);
 213
 214         if (phydev->drv->config)
 215                 phydev->drv->config(phydev);
 216
 217         return 0;
 218 }
 219
 220 #if defined(CONFIG_VIDEO_IPUV3)
 221 struct i2c_pads_info i2c2_pad_info = {
 222         .scl = {
 223                 .i2c_mode = MX6_PAD_KEY_COL3__I2C2_SCL
 224                         | MUX_PAD_CTRL(I2C_PAD_CTRL),
 225                 .gpio_mode = MX6_PAD_KEY_COL3__GPIO4_IO12
 226                         | MUX_PAD_CTRL(I2C_PAD_CTRL),
 227                 .gp = IMX_GPIO_NR(4, 12)
 228         },
 229         .sda = {
 230                 .i2c_mode = MX6_PAD_KEY_ROW3__I2C2_SDA
 231                         | MUX_PAD_CTRL(I2C_PAD_CTRL),
 232                 .gpio_mode = MX6_PAD_KEY_ROW3__GPIO4_IO13
 233                         | MUX_PAD_CTRL(I2C_PAD_CTRL),
 234                 .gp = IMX_GPIO_NR(4, 13)
 235         }
 236 };
 237
 238 static iomux_v3_cfg_t const fwadapt_7wvga_pads[] = {
 239         MX6_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK,
 240         MX6_PAD_DI0_PIN2__IPU1_DI0_PIN02, /* HSync */
 241         MX6_PAD_DI0_PIN3__IPU1_DI0_PIN03, /* VSync */
 242         MX6_PAD_DI0_PIN4__IPU1_DI0_PIN04
 243                 | MUX_PAD_CTRL(PAD_CTL_DSE_120ohm), /* Contrast */
 244         MX6_PAD_DI0_PIN15__IPU1_DI0_PIN15, /* DISP0_DRDY */
 245
 246         MX6_PAD_DISP0_DAT0__IPU1_DISP0_DATA00,
 247         MX6_PAD_DISP0_DAT1__IPU1_DISP0_DATA01,
 248         MX6_PAD_DISP0_DAT2__IPU1_DISP0_DATA02,
 249         MX6_PAD_DISP0_DAT3__IPU1_DISP0_DATA03,
 250         MX6_PAD_DISP0_DAT4__IPU1_DISP0_DATA04,
 251         MX6_PAD_DISP0_DAT5__IPU1_DISP0_DATA05,
 252         MX6_PAD_DISP0_DAT6__IPU1_DISP0_DATA06,
 253         MX6_PAD_DISP0_DAT7__IPU1_DISP0_DATA07,
 254         MX6_PAD_DISP0_DAT8__IPU1_DISP0_DATA08,
 255         MX6_PAD_DISP0_DAT9__IPU1_DISP0_DATA09,
 256         MX6_PAD_DISP0_DAT10__IPU1_DISP0_DATA10,
 257         MX6_PAD_DISP0_DAT11__IPU1_DISP0_DATA11,
 258         MX6_PAD_DISP0_DAT12__IPU1_DISP0_DATA12,
 259         MX6_PAD_DISP0_DAT13__IPU1_DISP0_DATA13,
 260         MX6_PAD_DISP0_DAT14__IPU1_DISP0_DATA14,
 261         MX6_PAD_DISP0_DAT15__IPU1_DISP0_DATA15,
 262         MX6_PAD_DISP0_DAT16__IPU1_DISP0_DATA16,
 263         MX6_PAD_DISP0_DAT17__IPU1_DISP0_DATA17,
 264
 265         MX6_PAD_SD4_DAT2__GPIO2_IO10
 266                 | MUX_PAD_CTRL(NO_PAD_CTRL), /* DISP0_BKLEN */
 267         MX6_PAD_SD4_DAT3__GPIO2_IO11
 268                 | MUX_PAD_CTRL(NO_PAD_CTRL), /* DISP0_VDDEN */
 269 };
 270
 271 static void do_enable_hdmi(struct display_info_t const *dev)
 272 {
 273         imx_enable_hdmi_phy();
 274 }
 275
 276 static int detect_i2c(struct display_info_t const *dev)
 277 {
 278         return (0 == i2c_set_bus_num(dev->bus)) &&
 279                         (0 == i2c_probe(dev->addr));
 280 }
 281
 282 static void enable_fwadapt_7wvga(struct display_info_t const *dev)
 283 {
 284         imx_iomux_v3_setup_multiple_pads(
 285                 fwadapt_7wvga_pads,
 286                 ARRAY_SIZE(fwadapt_7wvga_pads));
 287
 288         gpio_direction_output(IMX_GPIO_NR(2, 10), 1);
 289         gpio_direction_output(IMX_GPIO_NR(2, 11), 1);
 290 }
 291
 292 struct display_info_t const displays[] = {{
 293         .bus    = -1,
 294         .addr   = 0,
 295         .pixfmt = IPU_PIX_FMT_RGB24,
 296         .detect = detect_hdmi,
 297         .enable = do_enable_hdmi,
 298         .mode   = {
 299                 .name           = "HDMI",
 300                 .refresh        = 60,
 301                 .xres           = 1024,
 302                 .yres           = 768,
 303                 .pixclock       = 15385,
 304                 .left_margin    = 220,
 305                 .right_margin   = 40,
 306                 .upper_margin   = 21,
 307                 .lower_margin   = 7,
 308                 .hsync_len      = 60,
 309                 .vsync_len      = 10,
 310                 .sync           = FB_SYNC_EXT,
 311                 .vmode          = FB_VMODE_NONINTERLACED
 312 } }, {
 313         .bus    = 1,
 314         .addr   = 0x10,
 315         .pixfmt = IPU_PIX_FMT_RGB666,
 316         .detect = detect_i2c,
 317         .enable = enable_fwadapt_7wvga,
 318         .mode   = {
 319                 .name           = "FWBADAPT-LCD-F07A-0102",
 320                 .refresh        = 60,
 321                 .xres           = 800,
 322                 .yres           = 480,
 323                 .pixclock       = 33260,
 324                 .left_margin    = 128,
 325                 .right_margin   = 128,
 326                 .upper_margin   = 22,
 327                 .lower_margin   = 22,
 328                 .hsync_len      = 1,
 329                 .vsync_len      = 1,
 330                 .sync           = 0,
 331                 .vmode          = FB_VMODE_NONINTERLACED
 332 } } };
 333 size_t display_count = ARRAY_SIZE(displays);
 334
 335 static void setup_display(void)
 336 {
 337         struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
 338         int reg;
 339
 340         enable_ipu_clock();
 341         imx_setup_hdmi();
 342
 343         reg = readl(&mxc_ccm->chsccdr);
 344         reg |= (CHSCCDR_CLK_SEL_LDB_DI0
 345                 << MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
 346         writel(reg, &mxc_ccm->chsccdr);
 347
 348         /* Disable LCD backlight */
 349         imx_iomux_v3_setup_pad(MX6_PAD_DI0_PIN4__GPIO4_IO20);
 350         gpio_direction_input(IMX_GPIO_NR(4, 20));
 351 }
 352 #endif /* CONFIG_VIDEO_IPUV3 */
 353
 354 int board_eth_init(bd_t *bis)
 355 {
 356         setup_iomux_enet();
 357
 358         return cpu_eth_init(bis);
 359 }
 360
 361 int board_early_init_f(void)
 362 {
 363         setup_iomux_uart();
 364 #if defined(CONFIG_VIDEO_IPUV3)
 365         setup_display();
 366 #endif
 367         return 0;
 368 }
 369
 370 /*
 371  * Do not overwrite the console
 372  * Use always serial for U-Boot console
 373  */
 374 int overwrite_console(void)
 375 {
 376         return 1;
 377 }
 378
 379 #ifdef CONFIG_CMD_BMODE
 380 static const struct boot_mode board_boot_modes[] = {
 381         /* 4 bit bus width */
 382         {"mmc0",          MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00)},
 383         {"mmc1",          MAKE_CFGVAL(0x40, 0x20, 0x00, 0x00)},
 384         {NULL,   0},
 385 };
 386 #endif
 387
 388 int board_late_init(void)
 389 {
 390 #ifdef CONFIG_CMD_BMODE
 391         add_board_boot_modes(board_boot_modes);
 392 #endif
 393
 394         return 0;
 395 }
 396
 397 int board_init(void)
 398 {
 399         /* address of boot parameters */
 400         gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
 401
 402         setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c2_pad_info);
 403
 404         return 0;
 405 }
 406
 407 int checkboard(void)
 408 {
 409         puts("Board: Wandboard\n");
 410
 411         return 0;
 412 }