board/xes/xpedite517x/ddr.c

   1 /*
   2  * Copyright 2009 Extreme Engineering Solutions, Inc.
   3  * Copyright 2007-2008 Freescale Semiconductor, Inc.
   4  *
   5  * SPDX-License-Identifier:     GPL-2.0+
   6  */
   7
   8 #include <common.h>
   9 #include <i2c.h>
  10 #include <asm/fsl_ddr_sdram.h>
  11 #include <asm/fsl_ddr_dimm_params.h>
  12
  13 void get_spd(ddr2_spd_eeprom_t *spd, u8 i2c_address)
  14 {
  15         i2c_read(i2c_address, SPD_EEPROM_OFFSET, 2, (uchar *)spd,
  16                 sizeof(ddr2_spd_eeprom_t));
  17 }
  18
  19 /*
  20  * There are four board-specific SDRAM timing parameters which must be
  21  * calculated based on the particular PCB artwork.  These are:
  22  *   1.) CPO (Read Capture Delay)
  23  *           - TIMING_CFG_2 register
  24  *           Source: Calculation based on board trace lengths and
  25  *                   chip-specific internal delays.
  26  *   2.) WR_DATA_DELAY (Write Command to Data Strobe Delay)
  27  *           - TIMING_CFG_2 register
  28  *           Source: Calculation based on board trace lengths.
  29  *                   Unless clock and DQ lanes are very different
  30  *                   lengths (>2"), this should be set to the nominal value
  31  *                   of 1/2 clock delay.
  32  *   3.) CLK_ADJUST (Clock and Addr/Cmd alignment control)
  33  *           - DDR_SDRAM_CLK_CNTL register
  34  *           Source: Signal Integrity Simulations
  35  *   4.) 2T Timing on Addr/Ctl
  36  *           - TIMING_CFG_2 register
  37  *           Source: Signal Integrity Simulations
  38  *           Usually only needed with heavy load/very high speed (>DDR2-800)
  39  *
  40  *     PCB routing on the XPedite5170 is nearly identical to the XPedite5370
  41  *     so we use the XPedite5370 settings as a basis for the XPedite5170.
  42  */
  43
  44 typedef struct board_memctl_options {
  45         uint16_t datarate_mhz_low;
  46         uint16_t datarate_mhz_high;
  47         uint8_t clk_adjust;
  48         uint8_t cpo_override;
  49         uint8_t write_data_delay;
  50 } board_memctl_options_t;
  51
  52 static struct board_memctl_options bopts_ctrl[][2] = {
  53         {
  54                 /* Controller 0 */
  55                 {
  56                         /* DDR2 600/667 */
  57                         .datarate_mhz_low       = 500,
  58                         .datarate_mhz_high      = 750,
  59                         .clk_adjust             = 5,
  60                         .cpo_override           = 8,
  61                         .write_data_delay       = 2,
  62                 },
  63                 {
  64                         /* DDR2 800 */
  65                         .datarate_mhz_low       = 750,
  66                         .datarate_mhz_high      = 850,
  67                         .clk_adjust             = 5,
  68                         .cpo_override           = 9,
  69                         .write_data_delay       = 2,
  70                 },
  71         },
  72         {
  73                 /* Controller 1 */
  74                 {
  75                         /* DDR2 600/667 */
  76                         .datarate_mhz_low       = 500,
  77                         .datarate_mhz_high      = 750,
  78                         .clk_adjust             = 5,
  79                         .cpo_override           = 7,
  80                         .write_data_delay       = 2,
  81                 },
  82                 {
  83                         /* DDR2 800 */
  84                         .datarate_mhz_low       = 750,
  85                         .datarate_mhz_high      = 850,
  86                         .clk_adjust             = 5,
  87                         .cpo_override           = 8,
  88                         .write_data_delay       = 2,
  89                 },
  90         },
  91 };
  92
  93 void fsl_ddr_board_options(memctl_options_t *popts,
  94                         dimm_params_t *pdimm,
  95                         unsigned int ctrl_num)
  96 {
  97         struct board_memctl_options *bopts = bopts_ctrl[ctrl_num];
  98         sys_info_t sysinfo;
  99         int i;
 100         unsigned int datarate;
 101
 102         get_sys_info(&sysinfo);
 103         datarate = get_ddr_freq(0) / 1000000;
 104
 105         for (i = 0; i < ARRAY_SIZE(bopts_ctrl[ctrl_num]); i++) {
 106                 if ((bopts[i].datarate_mhz_low <= datarate) &&
 107                     (bopts[i].datarate_mhz_high >= datarate)) {
 108                         debug("controller %d:\n", ctrl_num);
 109                         debug(" clk_adjust = %d\n", bopts[i].clk_adjust);
 110                         debug(" cpo = %d\n", bopts[i].cpo_override);
 111                         debug(" write_data_delay = %d\n",
 112                                 bopts[i].write_data_delay);
 113                         popts->clk_adjust = bopts[i].clk_adjust;
 114                         popts->cpo_override = bopts[i].cpo_override;
 115                         popts->write_data_delay = bopts[i].write_data_delay;
 116                 }
 117         }
 118
 119         /*
 120          * Factors to consider for half-strength driver enable:
 121          *      - number of DIMMs installed
 122          */
 123         popts->half_strength_driver_enable = 0;
 124 }