]> Git Repo - J-u-boot.git/blame - include/configs/sama5d2_xplained.h
spl: Convert CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR to Kconfig
[J-u-boot.git] / include / configs / sama5d2_xplained.h
CommitLineData
75238f23
WY
1/*
2 * Configuration file for the SAMA5D2 Xplained Board.
3 *
4 * Copyright (C) 2015 Atmel Corporation
5 * Wenyou Yang <[email protected]>
6 *
7 * SPDX-License-Identifier: GPL-2.0+
8 */
9
10#ifndef __CONFIG_H
11#define __CONFIG_H
12
13/* No NOR flash, this definition should put before common header */
14#define CONFIG_SYS_NO_FLASH
15
16#include "at91-sama5_common.h"
17
2992dd83
WY
18#define CONFIG_BOARD_EARLY_INIT_F
19
0daa2e18
WY
20#define CONFIG_MISC_INIT_R
21
75238f23
WY
22/* SDRAM */
23#define CONFIG_NR_DRAM_BANKS 1
24#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_DDRCS
25#define CONFIG_SYS_SDRAM_SIZE 0x20000000
26
37dadbca
WY
27#ifdef CONFIG_SPL_BUILD
28#define CONFIG_SYS_INIT_SP_ADDR 0x210000
29#else
75238f23
WY
30#define CONFIG_SYS_INIT_SP_ADDR \
31 (CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE)
37dadbca 32#endif
75238f23
WY
33
34#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
35
75238f23
WY
36/* SerialFlash */
37#ifdef CONFIG_CMD_SF
75238f23
WY
38#define CONFIG_SF_DEFAULT_BUS 0
39#define CONFIG_SF_DEFAULT_CS 0
40#define CONFIG_SF_DEFAULT_SPEED 30000000
41#endif
42
43/* NAND flash */
44#undef CONFIG_CMD_NAND
45
46/* MMC */
75238f23 47#ifdef CONFIG_CMD_MMC
75238f23
WY
48#define CONFIG_GENERIC_MMC
49#define CONFIG_SDHCI
75238f23
WY
50#endif
51
52/* USB device */
75238f23
WY
53#define CONFIG_USB_ETHER
54#define CONFIG_USB_ETH_RNDIS
55#define CONFIG_USBNET_MANUFACTURER "Atmel SAMA5D2 XPlained"
56
57#if defined(CONFIG_CMD_USB) || defined(CONFIG_CMD_MMC)
75238f23
WY
58#define CONFIG_DOS_PARTITION
59#endif
60
0daa2e18
WY
61/* I2C */
62#define AT24MAC_ADDR 0x5c
63#define AT24MAC_REG 0x9a
64
75238f23
WY
65/* Ethernet Hardware */
66#define CONFIG_MACB
67#define CONFIG_RMII
68#define CONFIG_NET_RETRY_COUNT 20
69#define CONFIG_MACB_SEARCH_PHY
70
71/* LCD */
75238f23
WY
72
73#ifdef CONFIG_LCD
74#define LCD_BPP LCD_COLOR16
75#define LCD_OUTPUT_BPP 24
76#define CONFIG_LCD_LOGO
77#define CONFIG_LCD_INFO
78#define CONFIG_LCD_INFO_BELOW_LOGO
79#define CONFIG_SYS_WHITE_ON_BLACK
80#define CONFIG_ATMEL_HLCD
81#define CONFIG_ATMEL_LCD_RGB565
75238f23
WY
82#endif
83
84#ifdef CONFIG_SYS_USE_MMC
85
86/* bootstrap + u-boot + env in sd card */
87#undef FAT_ENV_DEVICE_AND_PART
88#undef CONFIG_BOOTCOMMAND
89
90#define FAT_ENV_DEVICE_AND_PART "1"
91#define CONFIG_BOOTCOMMAND "fatload mmc 1:1 0x21000000 at91-sama5d2_xplained.dtb; " \
92 "fatload mmc 1:1 0x22000000 zImage; " \
93 "bootz 0x22000000 - 0x21000000"
94#undef CONFIG_BOOTARGS
95#define CONFIG_BOOTARGS \
96 "console=ttyS0,115200 earlyprintk root=/dev/mmcblk1p2 rw rootwait"
97
98#endif
99
37dadbca
WY
100/* SPL */
101#define CONFIG_SPL_FRAMEWORK
102#define CONFIG_SPL_TEXT_BASE 0x200000
103#define CONFIG_SPL_MAX_SIZE 0x10000
104#define CONFIG_SPL_BSS_START_ADDR 0x20000000
105#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
106#define CONFIG_SYS_SPL_MALLOC_START 0x20080000
107#define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000
108
37dadbca
WY
109#define CONFIG_SPL_BOARD_INIT
110#define CONFIG_SYS_MONITOR_LEN (512 << 10)
111
112#ifdef CONFIG_SYS_USE_MMC
113#define CONFIG_SPL_LDSCRIPT arch/arm/mach-at91/armv7/u-boot-spl.lds
37dadbca 114#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x400
37dadbca
WY
115#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
116#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
37dadbca
WY
117
118#elif CONFIG_SYS_USE_SERIALFLASH
37dadbca
WY
119#define CONFIG_SPL_SPI_LOAD
120#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x8000
121
122#endif
123
75238f23 124#endif
This page took 0.186531 seconds and 4 git commands to generate.