]>
Commit | Line | Data |
---|---|---|
75238f23 WY |
1 | /* |
2 | * Configuration file for the SAMA5D2 Xplained Board. | |
3 | * | |
4 | * Copyright (C) 2015 Atmel Corporation | |
5 | * Wenyou Yang <[email protected]> | |
6 | * | |
7 | * SPDX-License-Identifier: GPL-2.0+ | |
8 | */ | |
9 | ||
10 | #ifndef __CONFIG_H | |
11 | #define __CONFIG_H | |
12 | ||
13 | /* No NOR flash, this definition should put before common header */ | |
14 | #define CONFIG_SYS_NO_FLASH | |
15 | ||
16 | #include "at91-sama5_common.h" | |
17 | ||
18 | /* serial console */ | |
19 | #define CONFIG_ATMEL_USART | |
20 | #define CONFIG_USART_BASE ATMEL_BASE_UART1 | |
21 | #define CONFIG_USART_ID ATMEL_ID_UART1 | |
22 | ||
23 | /* SDRAM */ | |
24 | #define CONFIG_NR_DRAM_BANKS 1 | |
25 | #define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_DDRCS | |
26 | #define CONFIG_SYS_SDRAM_SIZE 0x20000000 | |
27 | ||
28 | #define CONFIG_SYS_INIT_SP_ADDR \ | |
29 | (CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE) | |
30 | ||
31 | #define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */ | |
32 | ||
33 | #undef CONFIG_AT91_GPIO | |
34 | #define CONFIG_ATMEL_PIO4 | |
35 | ||
36 | /* SerialFlash */ | |
37 | #ifdef CONFIG_CMD_SF | |
38 | #define CONFIG_ATMEL_SPI | |
39 | #define CONFIG_ATMEL_SPI0 | |
40 | #define CONFIG_SPI_FLASH_ATMEL | |
41 | #define CONFIG_SF_DEFAULT_BUS 0 | |
42 | #define CONFIG_SF_DEFAULT_CS 0 | |
43 | #define CONFIG_SF_DEFAULT_SPEED 30000000 | |
44 | #endif | |
45 | ||
46 | /* NAND flash */ | |
47 | #undef CONFIG_CMD_NAND | |
48 | ||
49 | /* MMC */ | |
50 | #define CONFIG_CMD_MMC | |
51 | ||
52 | #ifdef CONFIG_CMD_MMC | |
53 | #define CONFIG_MMC | |
54 | #define CONFIG_GENERIC_MMC | |
55 | #define CONFIG_SDHCI | |
56 | #define CONFIG_ATMEL_SDHCI | |
57 | #define CONFIG_ATMEL_SDHCI0 | |
58 | #define CONFIG_ATMEL_SDHCI1 | |
59 | #define CONFIG_SUPPORT_EMMC_BOOT | |
60 | #endif | |
61 | ||
62 | /* USB */ | |
63 | #define CONFIG_CMD_USB | |
64 | ||
65 | #ifdef CONFIG_CMD_USB | |
66 | #define CONFIG_USB_EHCI | |
67 | #define CONFIG_USB_EHCI_ATMEL | |
68 | #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3 | |
69 | #define CONFIG_USB_STORAGE | |
70 | #endif | |
71 | ||
72 | /* USB device */ | |
73 | #define CONFIG_USB_GADGET | |
74 | #define CONFIG_USB_GADGET_DUALSPEED | |
75 | #define CONFIG_USB_GADGET_ATMEL_USBA | |
76 | #define CONFIG_USB_ETHER | |
77 | #define CONFIG_USB_ETH_RNDIS | |
78 | #define CONFIG_USBNET_MANUFACTURER "Atmel SAMA5D2 XPlained" | |
79 | ||
80 | #if defined(CONFIG_CMD_USB) || defined(CONFIG_CMD_MMC) | |
81 | #define CONFIG_CMD_FAT | |
82 | #define CONFIG_DOS_PARTITION | |
83 | #endif | |
84 | ||
85 | /* Ethernet Hardware */ | |
86 | #define CONFIG_MACB | |
87 | #define CONFIG_RMII | |
88 | #define CONFIG_NET_RETRY_COUNT 20 | |
89 | #define CONFIG_MACB_SEARCH_PHY | |
90 | ||
91 | /* LCD */ | |
92 | /* #define CONFIG_LCD */ | |
93 | ||
94 | #ifdef CONFIG_LCD | |
95 | #define LCD_BPP LCD_COLOR16 | |
96 | #define LCD_OUTPUT_BPP 24 | |
97 | #define CONFIG_LCD_LOGO | |
98 | #define CONFIG_LCD_INFO | |
99 | #define CONFIG_LCD_INFO_BELOW_LOGO | |
100 | #define CONFIG_SYS_WHITE_ON_BLACK | |
101 | #define CONFIG_ATMEL_HLCD | |
102 | #define CONFIG_ATMEL_LCD_RGB565 | |
103 | #define CONFIG_SYS_CONSOLE_IS_IN_ENV | |
104 | #endif | |
105 | ||
106 | #ifdef CONFIG_SYS_USE_MMC | |
107 | ||
108 | /* bootstrap + u-boot + env in sd card */ | |
109 | #undef FAT_ENV_DEVICE_AND_PART | |
110 | #undef CONFIG_BOOTCOMMAND | |
111 | ||
112 | #define FAT_ENV_DEVICE_AND_PART "1" | |
113 | #define CONFIG_BOOTCOMMAND "fatload mmc 1:1 0x21000000 at91-sama5d2_xplained.dtb; " \ | |
114 | "fatload mmc 1:1 0x22000000 zImage; " \ | |
115 | "bootz 0x22000000 - 0x21000000" | |
116 | #undef CONFIG_BOOTARGS | |
117 | #define CONFIG_BOOTARGS \ | |
118 | "console=ttyS0,115200 earlyprintk root=/dev/mmcblk1p2 rw rootwait" | |
119 | ||
120 | #endif | |
121 | ||
122 | #endif |