sunxi: Split out common board design for ALL-H3-CC device tree

The Libre Computer Project ALL-H3-CC has three models, all using the
same board design, but with different pin compatible SoCs and amount of
DRAM.

Currently only the H3 1GB DRAM variant is supported. To support the two
other variants, first split the original device tree into a common board
design part and an SoC specific part.

The SoC part only defines which SoC is used and model name, and includes
the SoC specific dtsi file and the common design dtsi file.

Also fix up the SPDX identifier line to use the correct comment style,
and place it on the first line.

Signed-off-by: Chen-Yu Tsai <[email protected]>
Acked-by: Maxime Ripard <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>

diff --git a/arch/arm/dts/sun8i-h3-libretech-all-h3-cc.dts b/arch/arm/dts/sun8i-h3-libretech-all-h3-cc.dts
index c8fd69f0a4b865921bb36a53eccbbe7549519149..50f2fb30d2d44191194ddfa1cdf3f8b5f0f03fd6 100644 (file)
--- a/arch/arm/dts/sun8i-h3-libretech-all-h3-cc.dts
+++ b/arch/arm/dts/sun8i-h3-libretech-all-h3-cc.dts
@@ -1,175 +1,13 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
 /*
  * Copyright (C) 2017 Chen-Yu Tsai <[email protected]>
- *
- * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
  */
 
 /dts-v1/;
 #include "sun8i-h3.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
+#include "sunxi-libretech-all-h3-cc.dtsi"
 
 / {
        model = "Libre Computer Board ALL-H3-CC H3";
        compatible = "libretech,all-h3-cc-h3", "allwinner,sun8i-h3";
-
-       aliases {
-               ethernet0 = &emac;
-               serial0 = &uart0;
-       };
-
-       chosen {
-               stdout-path = "serial0:115200n8";
-       };
-
-       leds {
-               compatible = "gpio-leds";
-
-               pwr_led {
-                       label = "librecomputer:green:pwr";
-                       gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
-                       default-state = "on";
-               };
-
-               status_led {
-                       label = "librecomputer:blue:status";
-                       gpios = <&pio 0 7 GPIO_ACTIVE_HIGH>; /* PA7 */
-               };
-       };
-
-       gpio_keys {
-               compatible = "gpio-keys";
-
-               power {
-                       label = "power";
-                       linux,code = <KEY_POWER>;
-                       gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
-               };
-       };
-
-       reg_vcc1v2: vcc1v2 {
-               compatible = "regulator-fixed";
-               regulator-name = "vcc1v2";
-               regulator-min-microvolt = <3300000>;
-               regulator-max-microvolt = <3300000>;
-               regulator-always-on;
-               regulator-boot-on;
-               vin-supply = <&reg_vcc5v0>;
-               gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
-               enable-active-high;
-       };
-
-       reg_vcc3v3: vcc3v3 {
-               compatible = "regulator-fixed";
-               regulator-name = "vcc3v3";
-               regulator-min-microvolt = <3300000>;
-               regulator-max-microvolt = <3300000>;
-               vin-supply = <&reg_vcc5v0>;
-       };
-
-       /* This represents the board's 5V input */
-       reg_vcc5v0: vcc5v0 {
-               compatible = "regulator-fixed";
-               regulator-name = "vcc5v0";
-               regulator-min-microvolt = <5000000>;
-               regulator-max-microvolt = <5000000>;
-       };
-
-       reg_vcc_dram: vcc-dram {
-               compatible = "regulator-fixed";
-               regulator-name = "vcc-dram";
-               regulator-min-microvolt = <1500000>;
-               regulator-max-microvolt = <1500000>;
-               regulator-always-on;
-               regulator-boot-on;
-               vin-supply = <&reg_vcc5v0>;
-               gpio = <&r_pio 0 9 GPIO_ACTIVE_HIGH>; /* PL9 */
-               enable-active-high;
-       };
-
-       reg_vcc_io: vcc-io {
-               compatible = "regulator-fixed";
-               regulator-name = "vcc-io";
-               regulator-min-microvolt = <3300000>;
-               regulator-max-microvolt = <3300000>;
-               regulator-always-on;
-               regulator-boot-on;
-               vin-supply = <&reg_vcc3v3>;
-               gpio = <&r_pio 0 5 GPIO_ACTIVE_LOW>; /* PL5 */
-       };
-
-       reg_vdd_cpux: vdd-cpux {
-               compatible = "regulator-fixed";
-               regulator-name = "vdd-cpux";
-               regulator-min-microvolt = <3300000>;
-               regulator-max-microvolt = <3300000>;
-               regulator-always-on;
-               regulator-boot-on;
-               vin-supply = <&reg_vcc5v0>;
-               gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
-               enable-active-high;
-       };
-};
-
-&ehci1 {
-       status = "okay";
-};
-
-&ehci2 {
-       status = "okay";
-};
-
-&ehci3 {
-       status = "okay";
-};
-
-&emac {
-       phy-handle = <&int_mii_phy>;
-       phy-mode = "mii";
-       allwinner,leds-active-low;
-       status = "okay";
-};
-
-&ir {
-       pinctrl-names = "default";
-       pinctrl-0 = <&ir_pins_a>;
-       status = "okay";
-};
-
-&mmc0 {
-       pinctrl-names = "default";
-       pinctrl-0 = <&mmc0_pins_a>;
-       vmmc-supply = <&reg_vcc_io>;
-       bus-width = <4>;
-       cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
-       cd-inverted;
-       status = "okay";
-};
-
-&ohci1 {
-       status = "okay";
-};
-
-&ohci2 {
-       status = "okay";
-};
-
-&ohci3 {
-       status = "okay";
-};
-
-&uart0 {
-       pinctrl-names = "default";
-       pinctrl-0 = <&uart0_pins_a>;
-       status = "okay";
-};
-
-&usbphy {
-       /* VBUS on USB ports are always on */
-       usb0_vbus-supply = <&reg_vcc5v0>;
-       usb1_vbus-supply = <&reg_vcc5v0>;
-       usb2_vbus-supply = <&reg_vcc5v0>;
-       usb3_vbus-supply = <&reg_vcc5v0>;
-       status = "okay";
 };

diff --git a/arch/arm/dts/sunxi-libretech-all-h3-cc.dtsi b/arch/arm/dts/sunxi-libretech-all-h3-cc.dtsi
new file mode 100644 (file)
index 0000000..5d01bba
--- /dev/null
+++ b/arch/arm/dts/sunxi-libretech-all-h3-cc.dtsi
@@ -0,0 +1,168 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2017 Chen-Yu Tsai <[email protected]>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+       aliases {
+               ethernet0 = &emac;
+               serial0 = &uart0;
+       };
+
+       chosen {
+               stdout-path = "serial0:115200n8";
+       };
+
+       leds {
+               compatible = "gpio-leds";
+
+               pwr_led {
+                       label = "librecomputer:green:pwr";
+                       gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
+                       default-state = "on";
+               };
+
+               status_led {
+                       label = "librecomputer:blue:status";
+                       gpios = <&pio 0 7 GPIO_ACTIVE_HIGH>; /* PA7 */
+               };
+       };
+
+       gpio_keys {
+               compatible = "gpio-keys";
+
+               power {
+                       label = "power";
+                       linux,code = <KEY_POWER>;
+                       gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
+               };
+       };
+
+       reg_vcc1v2: vcc1v2 {
+               compatible = "regulator-fixed";
+               regulator-name = "vcc1v2";
+               regulator-min-microvolt = <3300000>;
+               regulator-max-microvolt = <3300000>;
+               regulator-always-on;
+               regulator-boot-on;
+               vin-supply = <&reg_vcc5v0>;
+               gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
+               enable-active-high;
+       };
+
+       reg_vcc3v3: vcc3v3 {
+               compatible = "regulator-fixed";
+               regulator-name = "vcc3v3";
+               regulator-min-microvolt = <3300000>;
+               regulator-max-microvolt = <3300000>;
+               vin-supply = <&reg_vcc5v0>;
+       };
+
+       /* This represents the board's 5V input */
+       reg_vcc5v0: vcc5v0 {
+               compatible = "regulator-fixed";
+               regulator-name = "vcc5v0";
+               regulator-min-microvolt = <5000000>;
+               regulator-max-microvolt = <5000000>;
+       };
+
+       reg_vcc_dram: vcc-dram {
+               compatible = "regulator-fixed";
+               regulator-name = "vcc-dram";
+               regulator-min-microvolt = <1500000>;
+               regulator-max-microvolt = <1500000>;
+               regulator-always-on;
+               regulator-boot-on;
+               vin-supply = <&reg_vcc5v0>;
+               gpio = <&r_pio 0 9 GPIO_ACTIVE_HIGH>; /* PL9 */
+               enable-active-high;
+       };
+
+       reg_vcc_io: vcc-io {
+               compatible = "regulator-fixed";
+               regulator-name = "vcc-io";
+               regulator-min-microvolt = <3300000>;
+               regulator-max-microvolt = <3300000>;
+               regulator-always-on;
+               regulator-boot-on;
+               vin-supply = <&reg_vcc3v3>;
+               gpio = <&r_pio 0 5 GPIO_ACTIVE_LOW>; /* PL5 */
+       };
+
+       reg_vdd_cpux: vdd-cpux {
+               compatible = "regulator-fixed";
+               regulator-name = "vdd-cpux";
+               regulator-min-microvolt = <3300000>;
+               regulator-max-microvolt = <3300000>;
+               regulator-always-on;
+               regulator-boot-on;
+               vin-supply = <&reg_vcc5v0>;
+               gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
+               enable-active-high;
+       };
+};
+
+&ehci1 {
+       status = "okay";
+};
+
+&ehci2 {
+       status = "okay";
+};
+
+&ehci3 {
+       status = "okay";
+};
+
+&emac {
+       phy-handle = <&int_mii_phy>;
+       phy-mode = "mii";
+       allwinner,leds-active-low;
+       status = "okay";
+};
+
+&ir {
+       pinctrl-names = "default";
+       pinctrl-0 = <&ir_pins_a>;
+       status = "okay";
+};
+
+&mmc0 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&mmc0_pins_a>;
+       vmmc-supply = <&reg_vcc_io>;
+       bus-width = <4>;
+       cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+       cd-inverted;
+       status = "okay";
+};
+
+&ohci1 {
+       status = "okay";
+};
+
+&ohci2 {
+       status = "okay";
+};
+
+&ohci3 {
+       status = "okay";
+};
+
+&uart0 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&uart0_pins_a>;
+       status = "okay";
+};
+
+&usbphy {
+       /* VBUS on USB ports are always on */
+       usb0_vbus-supply = <&reg_vcc5v0>;
+       usb1_vbus-supply = <&reg_vcc5v0>;
+       usb2_vbus-supply = <&reg_vcc5v0>;
+       usb3_vbus-supply = <&reg_vcc5v0>;
+       status = "okay";
+};