1 // SPDX-License-Identifier: GPL-2.0
3 * Samsung's Exynos3250 based Rinato board device tree source
5 * Copyright (c) 2014 Samsung Electronics Co., Ltd.
6 * http://www.samsung.com
8 * Device tree source file for Samsung's Rinato board which is based on
9 * Samsung Exynos3250 SoC.
13 #include "exynos3250.dtsi"
14 #include "exynos4412-ppmu-common.dtsi"
15 #include <dt-bindings/input/input.h>
16 #include <dt-bindings/gpio/gpio.h>
17 #include <dt-bindings/clock/samsung,s2mps11.h>
20 model = "Samsung Rinato board";
21 compatible = "samsung,rinato", "samsung,exynos3250", "samsung,exynos3";
22 chassis-type = "watch";
31 stdout-path = &serial_1;
35 device_type = "memory";
36 reg = <0x40000000 0x1ff00000>;
40 compatible = "samsung,secure-firmware";
41 reg = <0x0205f000 0x1000>;
45 compatible = "gpio-keys";
48 gpios = <&gpx2 7 GPIO_ACTIVE_LOW>;
49 linux,code = <KEY_POWER>;
51 debounce-interval = <10>;
56 wlan_pwrseq: mshc1-pwrseq {
57 compatible = "mmc-pwrseq-simple";
58 reset-gpios = <&gpe0 4 GPIO_ACTIVE_LOW>;
61 i2c_max77836: i2c-gpio-0 {
62 compatible = "i2c-gpio";
63 sda-gpios = <&gpd0 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
64 scl-gpios = <&gpd0 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
69 compatible = "maxim,max77836";
70 interrupt-parent = <&gpx1>;
71 interrupts = <5 IRQ_TYPE_NONE>;
76 compatible = "maxim,max77836-muic";
80 compatible = "maxim,max77836-regulator";
81 safeout_reg: SAFEOUT {
82 regulator-name = "SAFEOUT";
85 charger_reg: CHARGER {
86 regulator-name = "CHARGER";
87 regulator-min-microamp = <45000>;
88 regulator-max-microamp = <475000>;
93 regulator-name = "MOT_2.7V";
94 regulator-min-microvolt = <1100000>;
95 regulator-max-microvolt = <2700000>;
99 regulator-name = "UNUSED_LDO2";
100 regulator-min-microvolt = <800000>;
101 regulator-max-microvolt = <3950000>;
106 compatible = "maxim,max77836-charger";
108 maxim,constant-uvolt = <4350000>;
109 maxim,fast-charge-uamp = <225000>;
110 maxim,eoc-uamp = <7500>;
111 maxim,ovp-uvolt = <6500000>;
117 compatible = "regulator-haptic";
118 haptic-supply = <&motor_reg>;
119 min-microvolt = <1100000>;
120 max-microvolt = <2700000>;
124 cpu_thermal: cpu-thermal {
127 /* Corresponds to 500MHz */
128 cooling-device = <&cpu0 5 5>,
132 /* Corresponds to 200MHz */
133 cooling-device = <&cpu0 8 8>,
142 vdd-supply = <&ldo3_reg>;
144 assigned-clocks = <&cmu CLK_SCLK_TSADC>;
145 assigned-clock-rates = <6000000>;
148 compatible = "murata,ncp15wb473";
149 pullup-uv = <1800000>;
150 pullup-ohm = <100000>;
151 pulldown-ohm = <100000>;
152 io-channels = <&adc 0>;
156 compatible = "murata,ncp15wb473";
157 pullup-uv = <1800000>;
158 pullup-ohm = <100000>;
159 pulldown-ohm = <100000>;
160 io-channels = <&adc 1>;
165 devfreq-events = <&ppmu_dmc0_3>, <&ppmu_dmc1_3>;
166 vdd-supply = <&buck1_reg>;
171 devfreq-events = <&ppmu_leftbus_3>, <&ppmu_rightbus_3>;
172 vdd-supply = <&buck3_reg>;
177 devfreq = <&bus_leftbus>;
182 devfreq = <&bus_leftbus>;
187 devfreq = <&bus_leftbus>;
192 devfreq = <&bus_leftbus>;
197 devfreq = <&bus_leftbus>;
202 devfreq = <&bus_leftbus>;
207 devfreq = <&bus_leftbus>;
216 cpu0-supply = <&buck2_reg>;
221 vbus-supply = <&safeout_reg>;
225 vusb_d-supply = <&ldo15_reg>;
226 vusb_a-supply = <&ldo12_reg>;
227 dr_mode = "peripheral";
232 vddcore-supply = <&ldo6_reg>;
233 vddio-supply = <&ldo6_reg>;
234 samsung,burst-clock-frequency = <250000000>;
235 samsung,esc-clock-frequency = <20000000>;
236 samsung,pll-clock-frequency = <24000000>;
240 compatible = "samsung,s6e63j0x03";
242 vdd3-supply = <&ldo16_reg>;
243 vci-supply = <&ldo20_reg>;
244 reset-gpios = <&gpe0 1 GPIO_ACTIVE_LOW>;
245 te-gpios = <&gpx0 6 GPIO_ACTIVE_HIGH>;
261 mali-supply = <&buck3_reg>;
266 #address-cells = <1>;
268 samsung,i2c-sda-delay = <100>;
269 samsung,i2c-slave-addr = <0x10>;
270 samsung,i2c-max-bus-freq = <100000>;
274 compatible = "samsung,s2mps14-pmic";
275 interrupt-parent = <&gpx0>;
276 interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
280 s2mps14_osc: clocks {
281 compatible = "samsung,s2mps14-clk";
283 clock-output-names = "s2mps14_ap", "unused",
289 regulator-name = "VAP_ALIVE_1.0V";
290 regulator-min-microvolt = <1000000>;
291 regulator-max-microvolt = <1000000>;
294 regulator-state-mem {
295 regulator-on-in-suspend;
300 regulator-name = "VAP_M1_1.2V";
301 regulator-min-microvolt = <1200000>;
302 regulator-max-microvolt = <1200000>;
305 regulator-state-mem {
306 regulator-off-in-suspend;
311 regulator-name = "VCC_AP_1.8V";
312 regulator-min-microvolt = <1800000>;
313 regulator-max-microvolt = <1800000>;
316 regulator-state-mem {
317 regulator-off-in-suspend;
322 regulator-name = "VAP_AVDD_PLL1";
323 regulator-min-microvolt = <1800000>;
324 regulator-max-microvolt = <1800000>;
327 regulator-state-mem {
328 regulator-off-in-suspend;
333 regulator-name = "VAP_PLL_ISO_1.0V";
334 regulator-min-microvolt = <1000000>;
335 regulator-max-microvolt = <1000000>;
338 regulator-state-mem {
339 regulator-off-in-suspend;
344 regulator-name = "VAP_VMIPI_1.0V";
345 regulator-min-microvolt = <1000000>;
346 regulator-max-microvolt = <1000000>;
349 regulator-state-mem {
350 regulator-off-in-suspend;
355 regulator-name = "VAP_AVDD_1.8V";
356 regulator-min-microvolt = <1800000>;
357 regulator-max-microvolt = <1800000>;
360 regulator-state-mem {
361 regulator-off-in-suspend;
366 regulator-name = "VAP_USB_3.0V";
367 regulator-min-microvolt = <3000000>;
368 regulator-max-microvolt = <3000000>;
371 regulator-state-mem {
372 regulator-off-in-suspend;
377 regulator-name = "V_LPDDR_1.2V";
378 regulator-min-microvolt = <1200000>;
379 regulator-max-microvolt = <1200000>;
382 regulator-state-mem {
383 regulator-on-in-suspend;
388 regulator-name = "UNUSED_LDO10";
389 regulator-min-microvolt = <1000000>;
390 regulator-max-microvolt = <1000000>;
392 regulator-state-mem {
393 regulator-off-in-suspend;
398 regulator-name = "V_EMMC_1.8V";
399 regulator-min-microvolt = <1800000>;
400 regulator-max-microvolt = <1800000>;
401 samsung,ext-control-gpios = <&gpk0 2 GPIO_ACTIVE_HIGH>;
405 regulator-name = "V_EMMC_2.8V";
406 regulator-min-microvolt = <2800000>;
407 regulator-max-microvolt = <2800000>;
408 samsung,ext-control-gpios = <&gpk0 2 GPIO_ACTIVE_HIGH>;
412 regulator-name = "CAM_AVDD_2.8V";
413 regulator-min-microvolt = <2800000>;
414 regulator-max-microvolt = <2800000>;
416 regulator-state-mem {
417 regulator-off-in-suspend;
422 regulator-name = "UNUSED_LDO14";
423 regulator-min-microvolt = <2700000>;
424 regulator-max-microvolt = <2700000>;
426 regulator-state-mem {
427 regulator-off-in-suspend;
432 regulator-name = "TSP_AVDD_3.3V";
433 regulator-min-microvolt = <3300000>;
434 regulator-max-microvolt = <3300000>;
436 regulator-state-mem {
437 regulator-off-in-suspend;
442 regulator-name = "LCD_VDD_3.3V";
443 regulator-min-microvolt = <3300000>;
444 regulator-max-microvolt = <3300000>;
446 regulator-state-mem {
447 regulator-off-in-suspend;
452 regulator-name = "V_IRLED_3.3V";
453 regulator-min-microvolt = <3300000>;
454 regulator-max-microvolt = <3300000>;
456 regulator-state-mem {
457 regulator-off-in-suspend;
462 regulator-name = "CAM_AF_2.8V";
463 regulator-min-microvolt = <2800000>;
464 regulator-max-microvolt = <2800000>;
466 regulator-state-mem {
467 regulator-off-in-suspend;
472 regulator-name = "TSP_VDD_1.8V";
473 regulator-min-microvolt = <1800000>;
474 regulator-max-microvolt = <1800000>;
476 regulator-state-mem {
477 regulator-off-in-suspend;
482 regulator-name = "LCD_VDD_1.8V";
483 regulator-min-microvolt = <1800000>;
484 regulator-max-microvolt = <1800000>;
486 regulator-state-mem {
487 regulator-off-in-suspend;
492 regulator-name = "CAM_IO_1.8V";
493 regulator-min-microvolt = <1800000>;
494 regulator-max-microvolt = <1800000>;
496 regulator-state-mem {
497 regulator-off-in-suspend;
502 regulator-name = "CAM_DVDD_1.2V";
503 regulator-min-microvolt = <1200000>;
504 regulator-max-microvolt = <1200000>;
506 regulator-state-mem {
507 regulator-off-in-suspend;
512 regulator-name = "HRM_VCC_1.8V";
513 regulator-min-microvolt = <1800000>;
514 regulator-max-microvolt = <1800000>;
519 regulator-name = "HRM_VCC_3.3V";
520 regulator-min-microvolt = <3000000>;
521 regulator-max-microvolt = <3000000>;
523 regulator-state-mem {
524 regulator-off-in-suspend;
529 regulator-name = "UNUSED_LDO25";
530 regulator-min-microvolt = <3000000>;
531 regulator-max-microvolt = <3000000>;
533 regulator-state-mem {
534 regulator-off-in-suspend;
539 regulator-name = "VAP_MIF_1.0V";
540 regulator-min-microvolt = <800000>;
541 regulator-max-microvolt = <900000>;
544 regulator-state-mem {
545 regulator-off-in-suspend;
550 regulator-name = "VAP_ARM_1.0V";
551 regulator-min-microvolt = <850000>;
552 regulator-max-microvolt = <1150000>;
555 regulator-state-mem {
556 regulator-off-in-suspend;
561 regulator-name = "VAP_INT3D_1.0V";
562 regulator-min-microvolt = <850000>;
563 regulator-max-microvolt = <1000000>;
566 regulator-state-mem {
567 regulator-off-in-suspend;
572 regulator-name = "VCC_SUB_1.95V";
573 regulator-min-microvolt = <1950000>;
574 regulator-max-microvolt = <1950000>;
577 regulator-state-mem {
578 regulator-on-in-suspend;
583 regulator-name = "VCC_SUB_1.35V";
584 regulator-min-microvolt = <1350000>;
585 regulator-max-microvolt = <1350000>;
588 regulator-state-mem {
589 regulator-on-in-suspend;
597 #address-cells = <1>;
599 samsung,i2c-sda-delay = <100>;
600 samsung,i2c-slave-addr = <0x10>;
601 samsung,i2c-max-bus-freq = <400000>;
605 compatible = "maxim,max77836-battery";
606 interrupt-parent = <&gpx1>;
607 interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
625 card-detect-delay = <200>;
626 vmmc-supply = <&ldo12_reg>;
627 clock-frequency = <100000000>;
628 max-frequency = <100000000>;
630 samsung,dw-mshc-ciu-div = <1>;
631 samsung,dw-mshc-sdr-timing = <0 1>;
632 samsung,dw-mshc-ddr-timing = <1 2>;
633 pinctrl-names = "default";
634 pinctrl-0 = <&sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8>;
642 #address-cells = <1>;
648 keep-power-in-suspend;
649 samsung,dw-mshc-ciu-div = <1>;
650 samsung,dw-mshc-sdr-timing = <0 1>;
651 samsung,dw-mshc-ddr-timing = <1 2>;
652 pinctrl-names = "default";
653 pinctrl-0 = <&sd1_clk &sd1_cmd &sd1_bus1 &sd1_bus4>;
656 mmc-pwrseq = <&wlan_pwrseq>;
659 compatible = "brcm,bcm4334-fmac", "brcm,bcm4329-fmac";
662 interrupt-parent = <&gpx1>;
663 interrupts = <1 IRQ_TYPE_LEVEL_HIGH>;
664 interrupt-names = "host-wake";
669 assigned-clocks = <&cmu CLK_SCLK_UART0>;
670 assigned-clock-rates = <100000000>;
674 compatible = "brcm,bcm4330-bt";
675 max-speed = <3000000>;
676 shutdown-gpios = <&gpe0 0 GPIO_ACTIVE_HIGH>;
677 device-wakeup-gpios = <&gpx3 1 GPIO_ACTIVE_HIGH>;
678 host-wakeup-gpios = <&gpx2 6 GPIO_ACTIVE_HIGH>;
679 clocks = <&s2mps14_osc S2MPS11_CLK_BT>;
688 vtmu-supply = <&ldo7_reg>;
693 clocks = <&cmu CLK_RTC>, <&s2mps14_osc S2MPS11_CLK_AP>;
694 clock-names = "rtc", "rtc_src";
699 clock-frequency = <24000000>;
703 pinctrl-names = "default";
704 pinctrl-0 = <&initial0 &sleep0>;
706 initial0: initial-state {
707 PIN_IN(gpa1-4, DOWN, LV1);
708 PIN_IN(gpa1-5, DOWN, LV1);
710 PIN_IN(gpc0-0, DOWN, LV1);
711 PIN_IN(gpc0-1, DOWN, LV1);
712 PIN_IN(gpc0-2, DOWN, LV1);
713 PIN_IN(gpc0-3, DOWN, LV1);
714 PIN_IN(gpc0-4, DOWN, LV1);
716 PIN_IN(gpd0-0, DOWN, LV1);
717 PIN_IN(gpd0-1, DOWN, LV1);
720 sleep0: sleep-state {
721 PIN_SLP(gpa0-0, INPUT, DOWN);
722 PIN_SLP(gpa0-1, INPUT, DOWN);
723 PIN_SLP(gpa0-2, INPUT, DOWN);
724 PIN_SLP(gpa0-3, INPUT, DOWN);
725 PIN_SLP(gpa0-4, INPUT, DOWN);
726 PIN_SLP(gpa0-5, INPUT, DOWN);
727 PIN_SLP(gpa0-6, INPUT, DOWN);
728 PIN_SLP(gpa0-7, INPUT, DOWN);
730 PIN_SLP(gpa1-0, INPUT, DOWN);
731 PIN_SLP(gpa1-1, INPUT, DOWN);
732 PIN_SLP(gpa1-2, INPUT, DOWN);
733 PIN_SLP(gpa1-3, INPUT, DOWN);
734 PIN_SLP(gpa1-4, INPUT, DOWN);
735 PIN_SLP(gpa1-5, INPUT, DOWN);
737 PIN_SLP(gpb-0, PREV, NONE);
738 PIN_SLP(gpb-1, PREV, NONE);
739 PIN_SLP(gpb-2, PREV, NONE);
740 PIN_SLP(gpb-3, PREV, NONE);
741 PIN_SLP(gpb-4, INPUT, DOWN);
742 PIN_SLP(gpb-5, INPUT, DOWN);
743 PIN_SLP(gpb-6, INPUT, DOWN);
744 PIN_SLP(gpb-7, INPUT, DOWN);
746 PIN_SLP(gpc0-0, INPUT, DOWN);
747 PIN_SLP(gpc0-1, INPUT, DOWN);
748 PIN_SLP(gpc0-2, INPUT, DOWN);
749 PIN_SLP(gpc0-3, INPUT, DOWN);
750 PIN_SLP(gpc0-4, INPUT, DOWN);
752 PIN_SLP(gpc1-0, INPUT, DOWN);
753 PIN_SLP(gpc1-1, INPUT, DOWN);
754 PIN_SLP(gpc1-2, INPUT, DOWN);
755 PIN_SLP(gpc1-3, INPUT, DOWN);
756 PIN_SLP(gpc1-4, INPUT, DOWN);
758 PIN_SLP(gpd0-0, INPUT, DOWN);
759 PIN_SLP(gpd0-1, INPUT, DOWN);
760 PIN_SLP(gpd0-2, INPUT, NONE);
761 PIN_SLP(gpd0-3, INPUT, NONE);
763 PIN_SLP(gpd1-0, INPUT, NONE);
764 PIN_SLP(gpd1-1, INPUT, NONE);
765 PIN_SLP(gpd1-2, INPUT, NONE);
766 PIN_SLP(gpd1-3, INPUT, NONE);
771 pinctrl-names = "default";
772 pinctrl-0 = <&initial1 &sleep1>;
774 initial1: initial-state {
775 PIN_IN(gpe0-6, DOWN, LV1);
776 PIN_IN(gpe0-7, DOWN, LV1);
778 PIN_IN(gpe1-0, DOWN, LV1);
779 PIN_IN(gpe1-3, DOWN, LV1);
780 PIN_IN(gpe1-4, DOWN, LV1);
781 PIN_IN(gpe1-5, DOWN, LV1);
782 PIN_IN(gpe1-6, DOWN, LV1);
784 PIN_IN(gpk2-0, DOWN, LV1);
785 PIN_IN(gpk2-1, DOWN, LV1);
786 PIN_IN(gpk2-2, DOWN, LV1);
787 PIN_IN(gpk2-3, DOWN, LV1);
788 PIN_IN(gpk2-4, DOWN, LV1);
789 PIN_IN(gpk2-5, DOWN, LV1);
790 PIN_IN(gpk2-6, DOWN, LV1);
792 PIN_IN(gpm0-0, DOWN, LV1);
793 PIN_IN(gpm0-1, DOWN, LV1);
794 PIN_IN(gpm0-2, DOWN, LV1);
795 PIN_IN(gpm0-3, DOWN, LV1);
796 PIN_IN(gpm0-4, DOWN, LV1);
797 PIN_IN(gpm0-5, DOWN, LV1);
798 PIN_IN(gpm0-6, DOWN, LV1);
799 PIN_IN(gpm0-7, DOWN, LV1);
801 PIN_IN(gpm1-0, DOWN, LV1);
802 PIN_IN(gpm1-1, DOWN, LV1);
803 PIN_IN(gpm1-2, DOWN, LV1);
804 PIN_IN(gpm1-3, DOWN, LV1);
805 PIN_IN(gpm1-4, DOWN, LV1);
806 PIN_IN(gpm1-5, DOWN, LV1);
807 PIN_IN(gpm1-6, DOWN, LV1);
809 PIN_IN(gpm2-0, DOWN, LV1);
810 PIN_IN(gpm2-1, DOWN, LV1);
812 PIN_IN(gpm3-0, DOWN, LV1);
813 PIN_IN(gpm3-1, DOWN, LV1);
814 PIN_IN(gpm3-2, DOWN, LV1);
815 PIN_IN(gpm3-3, DOWN, LV1);
816 PIN_IN(gpm3-4, DOWN, LV1);
818 PIN_IN(gpm4-1, DOWN, LV1);
819 PIN_IN(gpm4-2, DOWN, LV1);
820 PIN_IN(gpm4-3, DOWN, LV1);
821 PIN_IN(gpm4-4, DOWN, LV1);
822 PIN_IN(gpm4-5, DOWN, LV1);
823 PIN_IN(gpm4-6, DOWN, LV1);
824 PIN_IN(gpm4-7, DOWN, LV1);
827 sleep1: sleep-state {
828 PIN_SLP(gpe0-0, PREV, NONE);
829 PIN_SLP(gpe0-1, PREV, NONE);
830 PIN_SLP(gpe0-2, INPUT, DOWN);
831 PIN_SLP(gpe0-3, INPUT, UP);
832 PIN_SLP(gpe0-4, INPUT, DOWN);
833 PIN_SLP(gpe0-5, INPUT, DOWN);
834 PIN_SLP(gpe0-6, INPUT, DOWN);
835 PIN_SLP(gpe0-7, INPUT, DOWN);
837 PIN_SLP(gpe1-0, INPUT, DOWN);
838 PIN_SLP(gpe1-1, PREV, NONE);
839 PIN_SLP(gpe1-2, INPUT, DOWN);
840 PIN_SLP(gpe1-3, INPUT, DOWN);
841 PIN_SLP(gpe1-4, INPUT, DOWN);
842 PIN_SLP(gpe1-5, INPUT, DOWN);
843 PIN_SLP(gpe1-6, INPUT, DOWN);
844 PIN_SLP(gpe1-7, INPUT, NONE);
846 PIN_SLP(gpe2-0, INPUT, NONE);
847 PIN_SLP(gpe2-1, INPUT, NONE);
848 PIN_SLP(gpe2-2, INPUT, NONE);
850 PIN_SLP(gpk0-0, INPUT, DOWN);
851 PIN_SLP(gpk0-1, INPUT, DOWN);
852 PIN_SLP(gpk0-2, OUT0, NONE);
853 PIN_SLP(gpk0-3, INPUT, DOWN);
854 PIN_SLP(gpk0-4, INPUT, DOWN);
855 PIN_SLP(gpk0-5, INPUT, DOWN);
856 PIN_SLP(gpk0-6, INPUT, DOWN);
857 PIN_SLP(gpk0-7, INPUT, DOWN);
859 PIN_SLP(gpk1-0, INPUT, DOWN);
860 PIN_SLP(gpk1-1, INPUT, DOWN);
861 PIN_SLP(gpk1-2, INPUT, DOWN);
862 PIN_SLP(gpk1-3, INPUT, DOWN);
863 PIN_SLP(gpk1-4, INPUT, DOWN);
864 PIN_SLP(gpk1-5, INPUT, DOWN);
865 PIN_SLP(gpk1-6, INPUT, DOWN);
867 PIN_SLP(gpk2-0, INPUT, DOWN);
868 PIN_SLP(gpk2-1, INPUT, DOWN);
869 PIN_SLP(gpk2-2, INPUT, DOWN);
870 PIN_SLP(gpk2-3, INPUT, DOWN);
871 PIN_SLP(gpk2-4, INPUT, DOWN);
872 PIN_SLP(gpk2-5, INPUT, DOWN);
873 PIN_SLP(gpk2-6, INPUT, DOWN);
875 PIN_SLP(gpl0-0, INPUT, DOWN);
876 PIN_SLP(gpl0-1, INPUT, DOWN);
877 PIN_SLP(gpl0-2, INPUT, DOWN);
878 PIN_SLP(gpl0-3, INPUT, DOWN);
880 PIN_SLP(gpm0-0, INPUT, DOWN);
881 PIN_SLP(gpm0-1, INPUT, DOWN);
882 PIN_SLP(gpm0-2, INPUT, DOWN);
883 PIN_SLP(gpm0-3, INPUT, DOWN);
884 PIN_SLP(gpm0-4, INPUT, DOWN);
885 PIN_SLP(gpm0-5, INPUT, DOWN);
886 PIN_SLP(gpm0-6, INPUT, DOWN);
887 PIN_SLP(gpm0-7, INPUT, DOWN);
889 PIN_SLP(gpm1-0, INPUT, DOWN);
890 PIN_SLP(gpm1-1, INPUT, DOWN);
891 PIN_SLP(gpm1-2, INPUT, DOWN);
892 PIN_SLP(gpm1-3, INPUT, DOWN);
893 PIN_SLP(gpm1-4, INPUT, DOWN);
894 PIN_SLP(gpm1-5, INPUT, DOWN);
895 PIN_SLP(gpm1-6, INPUT, DOWN);
897 PIN_SLP(gpm2-0, INPUT, DOWN);
898 PIN_SLP(gpm2-1, INPUT, DOWN);
899 PIN_SLP(gpm2-2, INPUT, DOWN);
900 PIN_SLP(gpm2-3, INPUT, DOWN);
901 PIN_SLP(gpm2-4, INPUT, DOWN);
903 PIN_SLP(gpm3-0, INPUT, DOWN);
904 PIN_SLP(gpm3-1, INPUT, DOWN);
905 PIN_SLP(gpm3-2, INPUT, DOWN);
906 PIN_SLP(gpm3-3, INPUT, DOWN);
907 PIN_SLP(gpm3-4, INPUT, DOWN);
908 PIN_SLP(gpm3-5, INPUT, DOWN);
909 PIN_SLP(gpm3-6, INPUT, DOWN);
910 PIN_SLP(gpm3-7, INPUT, DOWN);
912 PIN_SLP(gpm4-0, INPUT, DOWN);
913 PIN_SLP(gpm4-1, INPUT, DOWN);
914 PIN_SLP(gpm4-2, INPUT, DOWN);
915 PIN_SLP(gpm4-3, INPUT, DOWN);
916 PIN_SLP(gpm4-4, INPUT, DOWN);
917 PIN_SLP(gpm4-5, INPUT, DOWN);
918 PIN_SLP(gpm4-6, INPUT, DOWN);
919 PIN_SLP(gpm4-7, INPUT, DOWN);