include/configs/MPC837XEMDS.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright (C) 2007 Freescale Semiconductor, Inc.
   4  * Dave Liu <[email protected]>
   5  */
   6
   7 #ifndef __CONFIG_H
   8 #define __CONFIG_H
   9
  10 /*
  11  * High Level Configuration Options
  12  */
  13 #define CONFIG_E300             1 /* E300 family */
  14
  15 /* Arbiter Configuration Register */
  16 #define CONFIG_SYS_ACR_PIPE_DEP 3       /* Arbiter pipeline depth is 4 */
  17 #define CONFIG_SYS_ACR_RPTCNT   3       /* Arbiter repeat count is 4 */
  18
  19 /* System Priority Control Register */
  20 #define CONFIG_SYS_SPCR_TSECEP  3 /* eTSEC1/2 emergency has highest priority */
  21
  22 /*
  23  * IP blocks clock configuration
  24  */
  25 #define CONFIG_SYS_SCCR_TSEC1CM 1       /* CSB:eTSEC1 = 1:1 */
  26 #define CONFIG_SYS_SCCR_TSEC2CM 1       /* CSB:eTSEC2 = 1:1 */
  27 #define CONFIG_SYS_SCCR_SATACM  SCCR_SATACM_2   /* CSB:SATA[0:3] = 2:1 */
  28
  29 /*
  30  * System IO Config
  31  */
  32 #define CONFIG_SYS_SICRH                0x00000000
  33 #define CONFIG_SYS_SICRL                0x00000000
  34
  35 /*
  36  * Output Buffer Impedance
  37  */
  38 #define CONFIG_SYS_OBIR         0x31100000
  39
  40 #define CONFIG_HWCONFIG
  41
  42 /*
  43  * IMMR new address
  44  */
  45 #define CONFIG_SYS_IMMR         0xE0000000
  46
  47 /*
  48  * DDR Setup
  49  */
  50 #define CONFIG_SYS_DDR_BASE             0x00000000 /* DDR is system memory */
  51 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_BASE
  52 #define CONFIG_SYS_DDR_SDRAM_BASE       CONFIG_SYS_DDR_BASE
  53 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL   DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
  54 #define CONFIG_SYS_83XX_DDR_USES_CS0
  55 #define CONFIG_SYS_DDRCDR_VALUE         (DDRCDR_DHC_EN \
  56                                         | DDRCDR_ODT \
  57                                         | DDRCDR_Q_DRN)
  58                                         /* 0x80080001 */ /* ODT 150ohm on SoC */
  59
  60 #undef CONFIG_DDR_ECC           /* support DDR ECC function */
  61 #undef CONFIG_DDR_ECC_CMD       /* Use DDR ECC user commands */
  62
  63 #define CONFIG_SPD_EEPROM       /* Use SPD EEPROM for DDR setup */
  64 #define CONFIG_NEVER_ASSERT_ODT_TO_CPU /* Never assert ODT to internal IOs */
  65
  66 #if defined(CONFIG_SPD_EEPROM)
  67 #define SPD_EEPROM_ADDRESS      0x51 /* I2C address of DDR SODIMM SPD */
  68 #else
  69 /*
  70  * Manually set up DDR parameters
  71  * WHITE ELECTRONIC DESIGNS - W3HG64M72EEU403PD4 SO-DIMM
  72  * consist of nine chips from SAMSUNG K4T51083QE-ZC(L)D5
  73  */
  74 #define CONFIG_SYS_DDR_SIZE             512 /* MB */
  75 #define CONFIG_SYS_DDR_CS0_BNDS 0x0000001f
  76 #define CONFIG_SYS_DDR_CS0_CONFIG       (CSCONFIG_EN \
  77                         | CSCONFIG_ODT_RD_NEVER  /* ODT_RD to none */ \
  78                         | CSCONFIG_ODT_WR_ONLY_CURRENT  /* ODT_WR to CSn */ \
  79                         | CSCONFIG_ROW_BIT_14 \
  80                         | CSCONFIG_COL_BIT_10)
  81                         /* 0x80010202 */
  82 #define CONFIG_SYS_DDR_TIMING_3 0x00000000
  83 #define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
  84                                 | (0 << TIMING_CFG0_WRT_SHIFT) \
  85                                 | (0 << TIMING_CFG0_RRT_SHIFT) \
  86                                 | (0 << TIMING_CFG0_WWT_SHIFT) \
  87                                 | (6 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
  88                                 | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
  89                                 | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
  90                                 | (2 << TIMING_CFG0_MRS_CYC_SHIFT))
  91                                 /* 0x00620802 */
  92 #define CONFIG_SYS_DDR_TIMING_1 ((3 << TIMING_CFG1_PRETOACT_SHIFT) \
  93                                 | (9 << TIMING_CFG1_ACTTOPRE_SHIFT) \
  94                                 | (3 << TIMING_CFG1_ACTTORW_SHIFT) \
  95                                 | (5 << TIMING_CFG1_CASLAT_SHIFT) \
  96                                 | (13 << TIMING_CFG1_REFREC_SHIFT) \
  97                                 | (3 << TIMING_CFG1_WRREC_SHIFT) \
  98                                 | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
  99                                 | (2 << TIMING_CFG1_WRTORD_SHIFT))
 100                                 /* 0x3935d322 */
 101 #define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \
 102                                 | (6 << TIMING_CFG2_CPO_SHIFT) \
 103                                 | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
 104                                 | (4 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
 105                                 | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
 106                                 | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
 107                                 | (8 << TIMING_CFG2_FOUR_ACT_SHIFT))
 108                                 /* 0x131088c8 */
 109 #define CONFIG_SYS_DDR_INTERVAL ((0x03E0 << SDRAM_INTERVAL_REFINT_SHIFT) \
 110                                 | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
 111                                 /* 0x03E00100 */
 112 #define CONFIG_SYS_DDR_SDRAM_CFG        0x43000000
 113 #define CONFIG_SYS_DDR_SDRAM_CFG2       0x00001000 /* 1 posted refresh */
 114 #define CONFIG_SYS_DDR_MODE     ((0x0448 << SDRAM_MODE_ESD_SHIFT) \
 115                                 | (0x1432 << SDRAM_MODE_SD_SHIFT))
 116                                 /* ODT 150ohm CL=3, AL=1 on SDRAM */
 117 #define CONFIG_SYS_DDR_MODE2    0x00000000
 118 #endif
 119
 120 /*
 121  * Memory test
 122  */
 123 #undef CONFIG_SYS_DRAM_TEST             /* memory test, takes time */
 124 #define CONFIG_SYS_MEMTEST_START        0x00040000 /* memtest region */
 125 #define CONFIG_SYS_MEMTEST_END          0x00140000
 126
 127 /*
 128  * The reserved memory
 129  */
 130 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
 131
 132 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 133 #define CONFIG_SYS_RAMBOOT
 134 #else
 135 #undef CONFIG_SYS_RAMBOOT
 136 #endif
 137
 138 /* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
 139 #define CONFIG_SYS_MONITOR_LEN  (512 * 1024) /* Reserve 512 kB for Mon */
 140 #define CONFIG_SYS_MALLOC_LEN   (512 * 1024) /* Reserved for malloc */
 141
 142 /*
 143  * Initial RAM Base Address Setup
 144  */
 145 #define CONFIG_SYS_INIT_RAM_LOCK        1
 146 #define CONFIG_SYS_INIT_RAM_ADDR        0xE6000000 /* Initial RAM address */
 147 #define CONFIG_SYS_INIT_RAM_SIZE        0x1000 /* Size of used area in RAM */
 148 #define CONFIG_SYS_GBL_DATA_OFFSET      \
 149                         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 150
 151 /*
 152  * Local Bus Configuration & Clock Setup
 153  */
 154 #define CONFIG_SYS_LCRR_DBYP    LCRR_DBYP
 155 #define CONFIG_SYS_LCRR_CLKDIV  LCRR_CLKDIV_8
 156 #define CONFIG_SYS_LBC_LBCR             0x00000000
 157 #define CONFIG_FSL_ELBC         1
 158
 159 /*
 160  * FLASH on the Local Bus
 161  */
 162 #define CONFIG_SYS_FLASH_BASE   0xFE000000 /* FLASH base address */
 163 #define CONFIG_SYS_FLASH_SIZE   32 /* max FLASH size is 32M */
 164
 165 #define CONFIG_SYS_BR0_PRELIM   (CONFIG_SYS_FLASH_BASE \
 166                                 | BR_PS_16      /* 16 bit port */ \
 167                                 | BR_MS_GPCM    /* MSEL = GPCM */ \
 168                                 | BR_V)         /* valid */
 169 #define CONFIG_SYS_OR0_PRELIM   (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
 170                                 | OR_UPM_XAM \
 171                                 | OR_GPCM_CSNT \
 172                                 | OR_GPCM_ACS_DIV2 \
 173                                 | OR_GPCM_XACS \
 174                                 | OR_GPCM_SCY_15 \
 175                                 | OR_GPCM_TRLX_SET \
 176                                 | OR_GPCM_EHTR_SET \
 177                                 | OR_GPCM_EAD)
 178                                 /* 0xFE000FF7 */
 179
 180 #define CONFIG_SYS_MAX_FLASH_BANKS      1 /* number of banks */
 181 #define CONFIG_SYS_MAX_FLASH_SECT       256 /* max sectors per device */
 182
 183 #undef CONFIG_SYS_FLASH_CHECKSUM
 184 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000 /* Flash Erase Timeout (ms) */
 185 #define CONFIG_SYS_FLASH_WRITE_TOUT     500 /* Flash Write Timeout (ms) */
 186
 187 /*
 188  * BCSR on the Local Bus
 189  */
 190 #define CONFIG_SYS_BCSR         0xF8000000
 191                                         /* Access window base at BCSR base */
 192 #define CONFIG_SYS_BR1_PRELIM   (CONFIG_SYS_BCSR \
 193                                 | BR_PS_8 \
 194                                 | BR_MS_GPCM \
 195                                 | BR_V)
 196                                 /* 0xF8000801 */
 197 #define CONFIG_SYS_OR1_PRELIM   (OR_AM_32KB \
 198                                 | OR_GPCM_XAM \
 199                                 | OR_GPCM_CSNT \
 200                                 | OR_GPCM_XACS \
 201                                 | OR_GPCM_SCY_15 \
 202                                 | OR_GPCM_TRLX_SET \
 203                                 | OR_GPCM_EHTR_SET \
 204                                 | OR_GPCM_EAD)
 205                                 /* 0xFFFFE9F7 */
 206
 207 /*
 208  * NAND Flash on the Local Bus
 209  */
 210 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 211 #define CONFIG_NAND_FSL_ELBC    1
 212
 213 #define CONFIG_SYS_NAND_BASE    0xE0600000
 214 #define CONFIG_SYS_BR3_PRELIM   (CONFIG_SYS_NAND_BASE \
 215                                 | BR_DECC_CHK_GEN       /* Use HW ECC */ \
 216                                 | BR_PS_8               /* 8 bit port */ \
 217                                 | BR_MS_FCM             /* MSEL = FCM */ \
 218                                 | BR_V)                 /* valid */
 219 #define CONFIG_SYS_OR3_PRELIM   (OR_AM_32KB \
 220                                 | OR_FCM_BCTLD \
 221                                 | OR_FCM_CST \
 222                                 | OR_FCM_CHT \
 223                                 | OR_FCM_SCY_1 \
 224                                 | OR_FCM_RST \
 225                                 | OR_FCM_TRLX \
 226                                 | OR_FCM_EHTR)
 227                                 /* 0xFFFF919E */
 228
 229 /*
 230  * Serial Port
 231  */
 232 #define CONFIG_SYS_NS16550_SERIAL
 233 #define CONFIG_SYS_NS16550_REG_SIZE     1
 234 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 235
 236 #define CONFIG_SYS_BAUDRATE_TABLE  \
 237                 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 238
 239 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
 240 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
 241
 242 /* I2C */
 243 #define CONFIG_SYS_I2C
 244 #define CONFIG_SYS_I2C_FSL
 245 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 246 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 247 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 248 #define CONFIG_SYS_I2C_NOPROBES         { {0, 0x51} }
 249
 250 /*
 251  * Config on-board RTC
 252  */
 253 #define CONFIG_RTC_DS1374       /* use ds1374 rtc via i2c */
 254 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */
 255
 256 /*
 257  * General PCI
 258  * Addresses are mapped 1-1.
 259  */
 260 #define CONFIG_SYS_PCI_MEM_BASE         0x80000000
 261 #define CONFIG_SYS_PCI_MEM_PHYS         CONFIG_SYS_PCI_MEM_BASE
 262 #define CONFIG_SYS_PCI_MEM_SIZE         0x10000000 /* 256M */
 263 #define CONFIG_SYS_PCI_MMIO_BASE        0x90000000
 264 #define CONFIG_SYS_PCI_MMIO_PHYS        CONFIG_SYS_PCI_MMIO_BASE
 265 #define CONFIG_SYS_PCI_MMIO_SIZE        0x10000000 /* 256M */
 266 #define CONFIG_SYS_PCI_IO_BASE          0x00000000
 267 #define CONFIG_SYS_PCI_IO_PHYS          0xE0300000
 268 #define CONFIG_SYS_PCI_IO_SIZE          0x100000 /* 1M */
 269
 270 #define CONFIG_SYS_PCI_SLV_MEM_LOCAL    CONFIG_SYS_SDRAM_BASE
 271 #define CONFIG_SYS_PCI_SLV_MEM_BUS      0x00000000
 272 #define CONFIG_SYS_PCI_SLV_MEM_SIZE     0x80000000
 273
 274 #define CONFIG_SYS_PCIE1_BASE           0xA0000000
 275 #define CONFIG_SYS_PCIE1_CFG_BASE       0xA0000000
 276 #define CONFIG_SYS_PCIE1_CFG_SIZE       0x08000000
 277 #define CONFIG_SYS_PCIE1_MEM_BASE       0xA8000000
 278 #define CONFIG_SYS_PCIE1_MEM_PHYS       0xA8000000
 279 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x10000000
 280 #define CONFIG_SYS_PCIE1_IO_BASE        0x00000000
 281 #define CONFIG_SYS_PCIE1_IO_PHYS        0xB8000000
 282 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00800000
 283
 284 #define CONFIG_SYS_PCIE2_BASE           0xC0000000
 285 #define CONFIG_SYS_PCIE2_CFG_BASE       0xC0000000
 286 #define CONFIG_SYS_PCIE2_CFG_SIZE       0x08000000
 287 #define CONFIG_SYS_PCIE2_MEM_BASE       0xC8000000
 288 #define CONFIG_SYS_PCIE2_MEM_PHYS       0xC8000000
 289 #define CONFIG_SYS_PCIE2_MEM_SIZE       0x10000000
 290 #define CONFIG_SYS_PCIE2_IO_BASE        0x00000000
 291 #define CONFIG_SYS_PCIE2_IO_PHYS        0xD8000000
 292 #define CONFIG_SYS_PCIE2_IO_SIZE        0x00800000
 293
 294 #ifdef CONFIG_PCI
 295 #define CONFIG_PCI_INDIRECT_BRIDGE
 296 #ifndef __ASSEMBLY__
 297 extern int board_pci_host_broken(void);
 298 #endif
 299 #define CONFIG_PCIE
 300 #define CONFIG_PQ_MDS_PIB       1 /* PQ MDS Platform IO Board */
 301
 302 #define CONFIG_HAS_FSL_DR_USB   1 /* fixup device tree for the DR USB */
 303 #define CONFIG_USB_EHCI_FSL
 304 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 305
 306 #undef CONFIG_EEPRO100
 307 #undef CONFIG_PCI_SCAN_SHOW     /* show pci devices on startup */
 308 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957   /* Freescale */
 309 #endif /* CONFIG_PCI */
 310
 311 /*
 312  * TSEC
 313  */
 314 #define CONFIG_SYS_TSEC1_OFFSET 0x24000
 315 #define CONFIG_SYS_TSEC1        (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
 316 #define CONFIG_SYS_TSEC2_OFFSET 0x25000
 317 #define CONFIG_SYS_TSEC2        (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
 318
 319 /*
 320  * TSEC ethernet configuration
 321  */
 322 #define CONFIG_TSEC1            1
 323 #define CONFIG_TSEC1_NAME       "eTSEC0"
 324 #define CONFIG_TSEC2            1
 325 #define CONFIG_TSEC2_NAME       "eTSEC1"
 326 #define TSEC1_PHY_ADDR          2
 327 #define TSEC2_PHY_ADDR          3
 328 #define TSEC1_PHY_ADDR_SGMII    8
 329 #define TSEC2_PHY_ADDR_SGMII    4
 330 #define TSEC1_PHYIDX            0
 331 #define TSEC2_PHYIDX            0
 332 #define TSEC1_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 333 #define TSEC2_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 334
 335 /* Options are: TSEC[0-1] */
 336 #define CONFIG_ETHPRIME         "eTSEC1"
 337
 338 /* SERDES */
 339 #define CONFIG_FSL_SERDES
 340 #define CONFIG_FSL_SERDES1      0xe3000
 341 #define CONFIG_FSL_SERDES2      0xe3100
 342
 343 /*
 344  * SATA
 345  */
 346 #define CONFIG_SYS_SATA_MAX_DEVICE      2
 347 #define CONFIG_SATA1
 348 #define CONFIG_SYS_SATA1_OFFSET 0x18000
 349 #define CONFIG_SYS_SATA1        (CONFIG_SYS_IMMR + CONFIG_SYS_SATA1_OFFSET)
 350 #define CONFIG_SYS_SATA1_FLAGS  FLAGS_DMA
 351 #define CONFIG_SATA2
 352 #define CONFIG_SYS_SATA2_OFFSET 0x19000
 353 #define CONFIG_SYS_SATA2        (CONFIG_SYS_IMMR + CONFIG_SYS_SATA2_OFFSET)
 354 #define CONFIG_SYS_SATA2_FLAGS  FLAGS_DMA
 355
 356 #ifdef CONFIG_FSL_SATA
 357 #define CONFIG_LBA48
 358 #endif
 359
 360 /*
 361  * Environment
 362  */
 363 #ifndef CONFIG_SYS_RAMBOOT
 364         #define CONFIG_ENV_ADDR         \
 365                         (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
 366         #define CONFIG_ENV_SECT_SIZE    0x20000 /* 128K(one sector) for env */
 367         #define CONFIG_ENV_SIZE         0x2000
 368 #else
 369         #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - 0x1000)
 370         #define CONFIG_ENV_SIZE         0x2000
 371 #endif
 372
 373 #define CONFIG_LOADS_ECHO       1       /* echo on for serial download */
 374 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */
 375
 376 /*
 377  * BOOTP options
 378  */
 379 #define CONFIG_BOOTP_BOOTFILESIZE
 380
 381 /*
 382  * Command line configuration.
 383  */
 384
 385 #undef CONFIG_WATCHDOG          /* watchdog disabled */
 386
 387 #ifdef CONFIG_MMC
 388 #define CONFIG_FSL_ESDHC_PIN_MUX
 389 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC83xx_ESDHC_ADDR
 390 #endif
 391
 392 /*
 393  * Miscellaneous configurable options
 394  */
 395 #define CONFIG_SYS_LOAD_ADDR            0x2000000 /* default load address */
 396
 397 /*
 398  * For booting Linux, the board info and command line data
 399  * have to be in the first 256 MB of memory, since this is
 400  * the maximum mapped by the Linux kernel during initialization.
 401  */
 402 #define CONFIG_SYS_BOOTMAPSZ    (256 << 20) /* Initial Memory map for Linux */
 403 #define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */
 404
 405 /*
 406  * Core HID Setup
 407  */
 408 #define CONFIG_SYS_HID0_INIT    0x000000000
 409 #define CONFIG_SYS_HID0_FINAL   (HID0_ENABLE_MACHINE_CHECK | \
 410                                  HID0_ENABLE_INSTRUCTION_CACHE)
 411 #define CONFIG_SYS_HID2         HID2_HBE
 412
 413 #if defined(CONFIG_CMD_KGDB)
 414 #define CONFIG_KGDB_BAUDRATE    230400  /* speed of kgdb serial port */
 415 #endif
 416
 417 /*
 418  * Environment Configuration
 419  */
 420
 421 #define CONFIG_ENV_OVERWRITE
 422
 423 #if defined(CONFIG_TSEC_ENET)
 424 #define CONFIG_HAS_ETH0
 425 #define CONFIG_HAS_ETH1
 426 #endif
 427
 428 #define CONFIG_LOADADDR 800000  /* default location for tftp and bootm */
 429
 430 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 431         "netdev=eth0\0"                                                 \
 432         "consoledev=ttyS0\0"                                            \
 433         "ramdiskaddr=1000000\0"                                         \
 434         "ramdiskfile=ramfs.83xx\0"                                      \
 435         "fdtaddr=780000\0"                                              \
 436         "fdtfile=mpc8379_mds.dtb\0"                                     \
 437         ""
 438
 439 #define CONFIG_NFSBOOTCOMMAND                                           \
 440         "setenv bootargs root=/dev/nfs rw "                             \
 441                 "nfsroot=$serverip:$rootpath "                          \
 442                 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:"   \
 443                                                         "$netdev:off "  \
 444                 "console=$consoledev,$baudrate $othbootargs;"           \
 445         "tftp $loadaddr $bootfile;"                                     \
 446         "tftp $fdtaddr $fdtfile;"                                       \
 447         "bootm $loadaddr - $fdtaddr"
 448
 449 #define CONFIG_RAMBOOTCOMMAND                                           \
 450         "setenv bootargs root=/dev/ram rw "                             \
 451                 "console=$consoledev,$baudrate $othbootargs;"           \
 452         "tftp $ramdiskaddr $ramdiskfile;"                               \
 453         "tftp $loadaddr $bootfile;"                                     \
 454         "tftp $fdtaddr $fdtfile;"                                       \
 455         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 456
 457 #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
 458
 459 #endif  /* __CONFIG_H */