include/configs/T208xRDB.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright 2014 Freescale Semiconductor, Inc.
   4  * Copyright 2020 NXP
   5  */
   6
   7 /*
   8  * T2080 RDB/PCIe board configuration file
   9  */
  10
  11 #ifndef __T2080RDB_H
  12 #define __T2080RDB_H
  13
  14 #define CONFIG_ICS307_REFCLK_HZ 25000000  /* ICS307 ref clk freq */
  15 #define CONFIG_FSL_SATA_V2
  16
  17 /* High Level Configuration Options */
  18 #define CONFIG_SYS_BOOK3E_HV    /* Category E.HV supported */
  19 #define CONFIG_ENABLE_36BIT_PHYS
  20
  21 #ifdef CONFIG_PHYS_64BIT
  22 #define CONFIG_ADDR_MAP 1
  23 #define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */
  24 #endif
  25
  26 #define CONFIG_SYS_FSL_CPC      /* Corenet Platform Cache */
  27 #define CONFIG_SYS_NUM_CPC      CONFIG_SYS_NUM_DDR_CTLRS
  28 #define CONFIG_ENV_OVERWRITE
  29
  30 #ifdef CONFIG_RAMBOOT_PBL
  31 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/t208xrdb/t2080_pbi.cfg
  32
  33 #define CONFIG_SPL_FLUSH_IMAGE
  34 #define CONFIG_SPL_PAD_TO               0x40000
  35 #define CONFIG_SPL_MAX_SIZE             0x28000
  36 #define RESET_VECTOR_OFFSET             0x27FFC
  37 #define BOOT_PAGE_OFFSET                0x27000
  38 #ifdef CONFIG_SPL_BUILD
  39 #define CONFIG_SPL_SKIP_RELOCATE
  40 #define CONFIG_SPL_COMMON_INIT_DDR
  41 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
  42 #endif
  43
  44 #ifdef CONFIG_MTD_RAW_NAND
  45 #define CONFIG_SYS_NAND_U_BOOT_SIZE     (768 << 10)
  46 #define CONFIG_SYS_NAND_U_BOOT_DST      0x00200000
  47 #define CONFIG_SYS_NAND_U_BOOT_START    0x00200000
  48 #define CONFIG_SYS_NAND_U_BOOT_OFFS     (256 << 10)
  49 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_nand_rcw.cfg
  50 #endif
  51
  52 #ifdef CONFIG_SPIFLASH
  53 #define        CONFIG_RESET_VECTOR_ADDRESS             0x200FFC
  54 #define CONFIG_SPL_SPI_FLASH_MINIMAL
  55 #define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE       (768 << 10)
  56 #define CONFIG_SYS_SPI_FLASH_U_BOOT_DST                (0x00200000)
  57 #define CONFIG_SYS_SPI_FLASH_U_BOOT_START      (0x00200000)
  58 #define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS       (256 << 10)
  59 #ifndef CONFIG_SPL_BUILD
  60 #define CONFIG_SYS_MPC85XX_NO_RESETVEC
  61 #endif
  62 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_spi_rcw.cfg
  63 #endif
  64
  65 #ifdef CONFIG_SDCARD
  66 #define        CONFIG_RESET_VECTOR_ADDRESS             0x200FFC
  67 #define CONFIG_SYS_MMC_U_BOOT_SIZE     (768 << 10)
  68 #define CONFIG_SYS_MMC_U_BOOT_DST      (0x00200000)
  69 #define CONFIG_SYS_MMC_U_BOOT_START    (0x00200000)
  70 #define CONFIG_SYS_MMC_U_BOOT_OFFS     (260 << 10)
  71 #ifndef CONFIG_SPL_BUILD
  72 #define CONFIG_SYS_MPC85XX_NO_RESETVEC
  73 #endif
  74 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_sd_rcw.cfg
  75 #endif
  76
  77 #endif /* CONFIG_RAMBOOT_PBL */
  78
  79 #define CONFIG_SRIO_PCIE_BOOT_MASTER
  80 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
  81 /* Set 1M boot space */
  82 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
  83 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
  84                 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
  85 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
  86 #endif
  87
  88 #ifndef CONFIG_RESET_VECTOR_ADDRESS
  89 #define CONFIG_RESET_VECTOR_ADDRESS     0xeffffffc
  90 #endif
  91
  92 /*
  93  * These can be toggled for performance analysis, otherwise use default.
  94  */
  95 #define CONFIG_SYS_CACHE_STASHING
  96 #define CONFIG_BTB              /* toggle branch predition */
  97 #define CONFIG_DDR_ECC
  98 #ifdef CONFIG_DDR_ECC
  99 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
 100 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
 101 #endif
 102
 103 #if defined(CONFIG_SPIFLASH)
 104 #elif defined(CONFIG_SDCARD)
 105 #define CONFIG_SYS_MMC_ENV_DEV  0
 106 #endif
 107
 108 #ifndef __ASSEMBLY__
 109 unsigned long get_board_sys_clk(void);
 110 unsigned long get_board_ddr_clk(void);
 111 #endif
 112
 113 #define CONFIG_SYS_CLK_FREQ     66660000
 114 #define CONFIG_DDR_CLK_FREQ     133330000
 115
 116 /*
 117  * Config the L3 Cache as L3 SRAM
 118  */
 119 #define CONFIG_SYS_INIT_L3_ADDR         0xFFFC0000
 120 #define CONFIG_SYS_L3_SIZE              (512 << 10)
 121 #define CONFIG_SPL_GD_ADDR              (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024)
 122 #define SPL_ENV_ADDR                    (CONFIG_SPL_GD_ADDR + 4 * 1024)
 123 #define CONFIG_SPL_RELOC_MALLOC_ADDR    (CONFIG_SPL_GD_ADDR + 12 * 1024)
 124 #define CONFIG_SPL_RELOC_MALLOC_SIZE    (50 << 10)
 125 #define CONFIG_SPL_RELOC_STACK          (CONFIG_SPL_GD_ADDR + 64 * 1024)
 126
 127 #define CONFIG_SYS_DCSRBAR      0xf0000000
 128 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
 129
 130 /* EEPROM */
 131 #define CONFIG_ID_EEPROM
 132 #define CONFIG_SYS_I2C_EEPROM_NXID
 133 #define CONFIG_SYS_EEPROM_BUS_NUM       0
 134 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x50
 135 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  2
 136
 137 /*
 138  * DDR Setup
 139  */
 140 #define CONFIG_VERY_BIG_RAM
 141 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000
 142 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
 143 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
 144 #define CONFIG_CHIP_SELECTS_PER_CTRL    (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
 145 #define CONFIG_DDR_SPD
 146 #define CONFIG_SYS_SPD_BUS_NUM  0
 147 #define CONFIG_SYS_SDRAM_SIZE   2048    /* for fixed parameter use */
 148 #define SPD_EEPROM_ADDRESS1     0x51
 149 #define SPD_EEPROM_ADDRESS2     0x52
 150 #define SPD_EEPROM_ADDRESS      SPD_EEPROM_ADDRESS1
 151 #define CTRL_INTLV_PREFERED     cacheline
 152
 153 /*
 154  * IFC Definitions
 155  */
 156 #define CONFIG_SYS_FLASH_BASE           0xe8000000
 157 #define CONFIG_SYS_FLASH_BASE_PHYS      (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
 158 #define CONFIG_SYS_NOR0_CSPR_EXT        (0xf)
 159 #define CONFIG_SYS_NOR0_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
 160                                 CSPR_PORT_SIZE_16 | \
 161                                 CSPR_MSEL_NOR | \
 162                                 CSPR_V)
 163 #define CONFIG_SYS_NOR_AMASK    IFC_AMASK(128*1024*1024)
 164
 165 /* NOR Flash Timing Params */
 166 #define CONFIG_SYS_NOR_CSOR     CSOR_NAND_TRHZ_80
 167
 168 #define CONFIG_SYS_NOR_FTIM0    (FTIM0_NOR_TACSE(0x4) | \
 169                                 FTIM0_NOR_TEADC(0x5) | \
 170                                 FTIM0_NOR_TEAHC(0x5))
 171 #define CONFIG_SYS_NOR_FTIM1    (FTIM1_NOR_TACO(0x35) | \
 172                                 FTIM1_NOR_TRAD_NOR(0x1A) |\
 173                                 FTIM1_NOR_TSEQRAD_NOR(0x13))
 174 #define CONFIG_SYS_NOR_FTIM2    (FTIM2_NOR_TCS(0x4) | \
 175                                 FTIM2_NOR_TCH(0x4) | \
 176                                 FTIM2_NOR_TWPH(0x0E) | \
 177                                 FTIM2_NOR_TWP(0x1c))
 178 #define CONFIG_SYS_NOR_FTIM3    0x0
 179
 180 #define CONFIG_SYS_FLASH_QUIET_TEST
 181 #define CONFIG_FLASH_SHOW_PROGRESS      45 /* count down from 45/5: 9..1 */
 182
 183 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* number of banks */
 184 #define CONFIG_SYS_MAX_FLASH_SECT       1024    /* sectors per device */
 185 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 186 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 187 #define CONFIG_SYS_FLASH_EMPTY_INFO
 188 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE_PHYS }
 189
 190 /* CPLD on IFC */
 191 #define CONFIG_SYS_CPLD_BASE    0xffdf0000
 192 #define CONFIG_SYS_CPLD_BASE_PHYS       (0xf00000000ull | CONFIG_SYS_CPLD_BASE)
 193 #define CONFIG_SYS_CSPR2_EXT    (0xf)
 194 #define CONFIG_SYS_CSPR2        (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE) \
 195                                 | CSPR_PORT_SIZE_8 \
 196                                 | CSPR_MSEL_GPCM \
 197                                 | CSPR_V)
 198 #define CONFIG_SYS_AMASK2       IFC_AMASK(64*1024)
 199 #define CONFIG_SYS_CSOR2        0x0
 200
 201 /* CPLD Timing parameters for IFC CS2 */
 202 #define CONFIG_SYS_CS2_FTIM0            (FTIM0_GPCM_TACSE(0x0e) | \
 203                                         FTIM0_GPCM_TEADC(0x0e) | \
 204                                         FTIM0_GPCM_TEAHC(0x0e))
 205 #define CONFIG_SYS_CS2_FTIM1            (FTIM1_GPCM_TACO(0x0e) | \
 206                                         FTIM1_GPCM_TRAD(0x1f))
 207 #define CONFIG_SYS_CS2_FTIM2            (FTIM2_GPCM_TCS(0x0e) | \
 208                                         FTIM2_GPCM_TCH(0x8) | \
 209                                         FTIM2_GPCM_TWP(0x1f))
 210 #define CONFIG_SYS_CS2_FTIM3            0x0
 211
 212 /* NAND Flash on IFC */
 213 #define CONFIG_NAND_FSL_IFC
 214 #define CONFIG_SYS_NAND_BASE            0xff800000
 215 #define CONFIG_SYS_NAND_BASE_PHYS       (0xf00000000ull | CONFIG_SYS_NAND_BASE)
 216
 217 #define CONFIG_SYS_NAND_CSPR_EXT        (0xf)
 218 #define CONFIG_SYS_NAND_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
 219                                 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
 220                                 | CSPR_MSEL_NAND         /* MSEL = NAND */ \
 221                                 | CSPR_V)
 222 #define CONFIG_SYS_NAND_AMASK   IFC_AMASK(64*1024)
 223
 224 #define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
 225                                 | CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
 226                                 | CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */     \
 227                                 | CSOR_NAND_RAL_3       /* RAL = 2Byes */   \
 228                                 | CSOR_NAND_PGS_2K      /* Page Size = 2K */\
 229                                 | CSOR_NAND_SPRZ_64     /* Spare size = 64 */\
 230                                 | CSOR_NAND_PB(64))     /*Pages Per Block = 64*/
 231
 232 #define CONFIG_SYS_NAND_ONFI_DETECTION
 233
 234 /* ONFI NAND Flash mode0 Timing Params */
 235 #define CONFIG_SYS_NAND_FTIM0           (FTIM0_NAND_TCCST(0x07) | \
 236                                         FTIM0_NAND_TWP(0x18)    | \
 237                                         FTIM0_NAND_TWCHT(0x07)  | \
 238                                         FTIM0_NAND_TWH(0x0a))
 239 #define CONFIG_SYS_NAND_FTIM1           (FTIM1_NAND_TADLE(0x32) | \
 240                                         FTIM1_NAND_TWBE(0x39)   | \
 241                                         FTIM1_NAND_TRR(0x0e)    | \
 242                                         FTIM1_NAND_TRP(0x18))
 243 #define CONFIG_SYS_NAND_FTIM2           (FTIM2_NAND_TRAD(0x0f)  | \
 244                                         FTIM2_NAND_TREH(0x0a)   | \
 245                                         FTIM2_NAND_TWHRE(0x1e))
 246 #define CONFIG_SYS_NAND_FTIM3           0x0
 247
 248 #define CONFIG_SYS_NAND_DDR_LAW         11
 249 #define CONFIG_SYS_NAND_BASE_LIST       { CONFIG_SYS_NAND_BASE }
 250 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 251 #define CONFIG_SYS_NAND_BLOCK_SIZE      (512 * 1024)
 252
 253 #if defined(CONFIG_MTD_RAW_NAND)
 254 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NAND_CSPR_EXT
 255 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NAND_CSPR
 256 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NAND_AMASK
 257 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NAND_CSOR
 258 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NAND_FTIM0
 259 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NAND_FTIM1
 260 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NAND_FTIM2
 261 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NAND_FTIM3
 262 #define CONFIG_SYS_CSPR1_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 263 #define CONFIG_SYS_CSPR1                CONFIG_SYS_NOR0_CSPR
 264 #define CONFIG_SYS_AMASK1               CONFIG_SYS_NOR_AMASK
 265 #define CONFIG_SYS_CSOR1                CONFIG_SYS_NOR_CSOR
 266 #define CONFIG_SYS_CS1_FTIM0            CONFIG_SYS_NOR_FTIM0
 267 #define CONFIG_SYS_CS1_FTIM1            CONFIG_SYS_NOR_FTIM1
 268 #define CONFIG_SYS_CS1_FTIM2            CONFIG_SYS_NOR_FTIM2
 269 #define CONFIG_SYS_CS1_FTIM3            CONFIG_SYS_NOR_FTIM3
 270 #else
 271 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 272 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NOR0_CSPR
 273 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NOR_AMASK
 274 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NOR_CSOR
 275 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NOR_FTIM0
 276 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NOR_FTIM1
 277 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NOR_FTIM2
 278 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NOR_FTIM3
 279 #define CONFIG_SYS_CSPR1_EXT            CONFIG_SYS_NAND_CSPR_EXT
 280 #define CONFIG_SYS_CSPR1                CONFIG_SYS_NAND_CSPR
 281 #define CONFIG_SYS_AMASK1               CONFIG_SYS_NAND_AMASK
 282 #define CONFIG_SYS_CSOR1                CONFIG_SYS_NAND_CSOR
 283 #define CONFIG_SYS_CS1_FTIM0            CONFIG_SYS_NAND_FTIM0
 284 #define CONFIG_SYS_CS1_FTIM1            CONFIG_SYS_NAND_FTIM1
 285 #define CONFIG_SYS_CS1_FTIM2            CONFIG_SYS_NAND_FTIM2
 286 #define CONFIG_SYS_CS1_FTIM3            CONFIG_SYS_NAND_FTIM3
 287 #endif
 288
 289 #if defined(CONFIG_RAMBOOT_PBL)
 290 #define CONFIG_SYS_RAMBOOT
 291 #endif
 292
 293 #ifdef CONFIG_SPL_BUILD
 294 #define CONFIG_SYS_MONITOR_BASE  CONFIG_SPL_TEXT_BASE
 295 #else
 296 #define CONFIG_SYS_MONITOR_BASE  CONFIG_SYS_TEXT_BASE /* start of monitor */
 297 #endif
 298
 299 #define CONFIG_HWCONFIG
 300
 301 /* define to use L1 as initial stack */
 302 #define CONFIG_L1_INIT_RAM
 303 #define CONFIG_SYS_INIT_RAM_LOCK
 304 #define CONFIG_SYS_INIT_RAM_ADDR        0xfdd00000 /* Initial L1 address */
 305 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH      0xf
 306 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW       0xfe03c000
 307 /* The assembler doesn't like typecast */
 308 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
 309                         ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
 310                         CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
 311 #define CONFIG_SYS_INIT_RAM_SIZE        0x00004000
 312 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - \
 313                                                 GENERATED_GBL_DATA_SIZE)
 314 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 315 #define CONFIG_SYS_MONITOR_LEN          (768 * 1024)
 316 #define CONFIG_SYS_MALLOC_LEN           (4 * 1024 * 1024)
 317
 318 /*
 319  * Serial Port
 320  */
 321 #define CONFIG_SYS_NS16550_SERIAL
 322 #define CONFIG_SYS_NS16550_REG_SIZE     1
 323 #define CONFIG_SYS_NS16550_CLK          (get_bus_freq(0)/2)
 324 #define CONFIG_SYS_BAUDRATE_TABLE       \
 325         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 326 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
 327 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
 328 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
 329 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
 330
 331 /*
 332  * I2C
 333  */
 334 #ifndef CONFIG_DM_I2C
 335 #define CONFIG_SYS_I2C
 336 #define CONFIG_SYS_FSL_I2C_SLAVE   0x7F
 337 #define CONFIG_SYS_FSL_I2C2_SLAVE  0x7F
 338 #define CONFIG_SYS_FSL_I2C3_SLAVE  0x7F
 339 #define CONFIG_SYS_FSL_I2C4_SLAVE  0x7F
 340 #define CONFIG_SYS_FSL_I2C_OFFSET  0x118000
 341 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100
 342 #define CONFIG_SYS_FSL_I2C3_OFFSET 0x119000
 343 #define CONFIG_SYS_FSL_I2C4_OFFSET 0x119100
 344 #define CONFIG_SYS_FSL_I2C_SPEED   100000
 345 #define CONFIG_SYS_FSL_I2C2_SPEED  100000
 346 #define CONFIG_SYS_FSL_I2C3_SPEED  100000
 347 #define CONFIG_SYS_FSL_I2C4_SPEED  100000
 348 #else
 349 #define CONFIG_I2C_SET_DEFAULT_BUS_NUM
 350 #define CONFIG_I2C_DEFAULT_BUS_NUMBER   0
 351 #endif
 352
 353 #define CONFIG_SYS_I2C_FSL
 354
 355 #define I2C_MUX_PCA_ADDR_PRI    0x77 /* I2C bus multiplexer,primary */
 356 #define I2C_MUX_PCA_ADDR_SEC1   0x75 /* I2C bus multiplexer,secondary 1 */
 357 #define I2C_MUX_PCA_ADDR_SEC2   0x76 /* I2C bus multiplexer,secondary 2 */
 358 #define I2C_MUX_CH_DEFAULT      0x8
 359
 360 #define I2C_MUX_CH_VOL_MONITOR  0xa
 361
 362 #define CONFIG_VID_FLS_ENV              "t208xrdb_vdd_mv"
 363 #ifndef CONFIG_SPL_BUILD
 364 #define CONFIG_VID
 365 #endif
 366 #define CONFIG_VOL_MONITOR_IR36021_SET
 367 #define CONFIG_VOL_MONITOR_IR36021_READ
 368 /* The lowest and highest voltage allowed for T208xRDB */
 369 #define VDD_MV_MIN                      819
 370 #define VDD_MV_MAX                      1212
 371
 372 /*
 373  * RapidIO
 374  */
 375 #define CONFIG_SYS_SRIO1_MEM_VIRT       0xa0000000
 376 #define CONFIG_SYS_SRIO1_MEM_PHYS       0xc20000000ull
 377 #define CONFIG_SYS_SRIO1_MEM_SIZE       0x10000000 /* 256M */
 378 #define CONFIG_SYS_SRIO2_MEM_VIRT       0xb0000000
 379 #define CONFIG_SYS_SRIO2_MEM_PHYS       0xc30000000ull
 380 #define CONFIG_SYS_SRIO2_MEM_SIZE       0x10000000 /* 256M */
 381 /*
 382  * for slave u-boot IMAGE instored in master memory space,
 383  * PHYS must be aligned based on the SIZE
 384  */
 385 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
 386 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
 387 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE     0x100000 /* 1M */
 388 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
 389 /*
 390  * for slave UCODE and ENV instored in master memory space,
 391  * PHYS must be aligned based on the SIZE
 392  */
 393 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
 394 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
 395 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE    0x40000 /* 256K */
 396
 397 /* slave core release by master*/
 398 #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
 399 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */
 400
 401 /*
 402  * SRIO_PCIE_BOOT - SLAVE
 403  */
 404 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
 405 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
 406 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
 407                 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
 408 #endif
 409
 410 /*
 411  * eSPI - Enhanced SPI
 412  */
 413
 414 /*
 415  * General PCI
 416  * Memory space is mapped 1-1, but I/O space must start from 0.
 417  */
 418 #define CONFIG_PCIE1            /* PCIE controller 1 */
 419 #define CONFIG_PCIE2            /* PCIE controller 2 */
 420 #define CONFIG_PCIE3            /* PCIE controller 3 */
 421 #define CONFIG_PCIE4            /* PCIE controller 4 */
 422 #define CONFIG_SYS_PCI_64BIT    /* enable 64-bit PCI resources */
 423 /* controller 1, direct to uli, tgtid 3, Base address 20000 */
 424 #define CONFIG_SYS_PCIE1_MEM_VIRT       0x80000000
 425 #define CONFIG_SYS_PCIE1_MEM_PHYS       0xc00000000ull
 426 #define CONFIG_SYS_PCIE1_IO_VIRT        0xf8000000
 427 #define CONFIG_SYS_PCIE1_IO_PHYS        0xff8000000ull
 428
 429 /* controller 2, Slot 2, tgtid 2, Base address 201000 */
 430 #define CONFIG_SYS_PCIE2_MEM_VIRT       0xa0000000
 431 #define CONFIG_SYS_PCIE2_MEM_PHYS       0xc20000000ull
 432 #define CONFIG_SYS_PCIE2_IO_VIRT        0xf8010000
 433 #define CONFIG_SYS_PCIE2_IO_PHYS        0xff8010000ull
 434
 435 /* controller 3, Slot 1, tgtid 1, Base address 202000 */
 436 #define CONFIG_SYS_PCIE3_MEM_VIRT       0xb0000000
 437 #define CONFIG_SYS_PCIE3_MEM_PHYS       0xc30000000ull
 438 #define CONFIG_SYS_PCIE3_IO_VIRT        0xf8020000
 439 #define CONFIG_SYS_PCIE3_IO_PHYS        0xff8020000ull
 440
 441 /* controller 4, Base address 203000 */
 442 #define CONFIG_SYS_PCIE4_MEM_VIRT       0xc0000000
 443 #define CONFIG_SYS_PCIE4_MEM_PHYS       0xc40000000ull
 444 #define CONFIG_SYS_PCIE4_IO_PHYS        0xff8030000ull
 445
 446 #ifdef CONFIG_PCI
 447 #if !defined(CONFIG_DM_PCI)
 448 #define CONFIG_FSL_PCI_INIT     /* Use common FSL init code */
 449 #define CONFIG_SYS_PCIE1_MEM_BUS        0xe0000000
 450 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x20000000      /* 512M */
 451 #define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
 452 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00010000      /* 64k */
 453 #define CONFIG_SYS_PCIE2_MEM_BUS        0xe0000000
 454 #define CONFIG_SYS_PCIE2_MEM_SIZE       0x10000000 /* 256M */
 455 #define CONFIG_SYS_PCIE2_IO_BUS         0x00000000
 456 #define CONFIG_SYS_PCIE2_IO_SIZE        0x00010000      /* 64k */
 457 #define CONFIG_SYS_PCIE3_MEM_BUS        0xe0000000
 458 #define CONFIG_SYS_PCIE3_MEM_SIZE       0x10000000      /* 256M */
 459 #define CONFIG_SYS_PCIE3_IO_BUS         0x00000000
 460 #define CONFIG_SYS_PCIE3_IO_SIZE        0x00010000      /* 64k */
 461 #define CONFIG_SYS_PCIE4_MEM_BUS        0xe0000000
 462 #define CONFIG_SYS_PCIE4_MEM_SIZE       0x10000000      /* 256M */
 463 #define CONFIG_SYS_PCIE4_IO_BUS         0x00000000
 464 #define CONFIG_SYS_PCIE4_IO_SIZE        0x00010000      /* 64k */
 465 #define CONFIG_PCI_INDIRECT_BRIDGE
 466 #endif
 467 #define CONFIG_PCI_SCAN_SHOW    /* show pci devices on startup */
 468 #endif
 469
 470 /* Qman/Bman */
 471 #ifndef CONFIG_NOBQFMAN
 472 #define CONFIG_SYS_BMAN_NUM_PORTALS     18
 473 #define CONFIG_SYS_BMAN_MEM_BASE        0xf4000000
 474 #define CONFIG_SYS_BMAN_MEM_PHYS        0xff4000000ull
 475 #define CONFIG_SYS_BMAN_MEM_SIZE        0x02000000
 476 #define CONFIG_SYS_BMAN_SP_CENA_SIZE    0x4000
 477 #define CONFIG_SYS_BMAN_SP_CINH_SIZE    0x1000
 478 #define CONFIG_SYS_BMAN_CENA_BASE       CONFIG_SYS_BMAN_MEM_BASE
 479 #define CONFIG_SYS_BMAN_CENA_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 480 #define CONFIG_SYS_BMAN_CINH_BASE       (CONFIG_SYS_BMAN_MEM_BASE + \
 481                                         CONFIG_SYS_BMAN_CENA_SIZE)
 482 #define CONFIG_SYS_BMAN_CINH_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 483 #define CONFIG_SYS_BMAN_SWP_ISDR_REG    0xE08
 484 #define CONFIG_SYS_QMAN_NUM_PORTALS     18
 485 #define CONFIG_SYS_QMAN_MEM_BASE        0xf6000000
 486 #define CONFIG_SYS_QMAN_MEM_PHYS        0xff6000000ull
 487 #define CONFIG_SYS_QMAN_MEM_SIZE        0x02000000
 488 #define CONFIG_SYS_QMAN_SP_CENA_SIZE    0x4000
 489 #define CONFIG_SYS_QMAN_SP_CINH_SIZE    0x1000
 490 #define CONFIG_SYS_QMAN_CENA_BASE       CONFIG_SYS_QMAN_MEM_BASE
 491 #define CONFIG_SYS_QMAN_CENA_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 492 #define CONFIG_SYS_QMAN_CINH_BASE       (CONFIG_SYS_QMAN_MEM_BASE + \
 493                                         CONFIG_SYS_QMAN_CENA_SIZE)
 494 #define CONFIG_SYS_QMAN_CINH_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 495 #define CONFIG_SYS_QMAN_SWP_ISDR_REG    0xE08
 496
 497 #define CONFIG_SYS_DPAA_FMAN
 498 #define CONFIG_SYS_DPAA_PME
 499 #define CONFIG_SYS_PMAN
 500 #define CONFIG_SYS_DPAA_DCE
 501 #define CONFIG_SYS_DPAA_RMAN            /* RMan */
 502 #define CONFIG_SYS_INTERLAKEN
 503
 504 /* Default address of microcode for the Linux Fman driver */
 505 #if defined(CONFIG_SPIFLASH)
 506 /*
 507  * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
 508  * env, so we got 0x110000.
 509  */
 510 #define CONFIG_SYS_FMAN_FW_ADDR         0x110000
 511 #define CONFIG_CORTINA_FW_ADDR          0x120000
 512
 513 #elif defined(CONFIG_SDCARD)
 514 /*
 515  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
 516  * about 1MB (2048 blocks), Env is stored after the image, and the env size is
 517  * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080.
 518  */
 519 #define CONFIG_SYS_FMAN_FW_ADDR         (512 * 0x820)
 520 #define CONFIG_CORTINA_FW_ADDR          (512 * 0x8a0)
 521
 522 #elif defined(CONFIG_MTD_RAW_NAND)
 523 #define CONFIG_SYS_FMAN_FW_ADDR         (3 * CONFIG_SYS_NAND_BLOCK_SIZE)
 524 #define CONFIG_CORTINA_FW_ADDR          (4 * CONFIG_SYS_NAND_BLOCK_SIZE)
 525 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
 526 /*
 527  * Slave has no ucode locally, it can fetch this from remote. When implementing
 528  * in two corenet boards, slave's ucode could be stored in master's memory
 529  * space, the address can be mapped from slave TLB->slave LAW->
 530  * slave SRIO or PCIE outbound window->master inbound window->
 531  * master LAW->the ucode address in master's memory space.
 532  */
 533 #define CONFIG_SYS_FMAN_FW_ADDR         0xFFE00000
 534 #define CONFIG_CORTINA_FW_ADDR          0xFFE10000
 535 #else
 536 #define CONFIG_SYS_FMAN_FW_ADDR         0xEFF00000
 537 #define CONFIG_CORTINA_FW_ADDR          0xEFE00000
 538 #endif
 539 #define CONFIG_SYS_QE_FMAN_FW_LENGTH    0x10000
 540 #define CONFIG_SYS_FDT_PAD              (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 541 #endif /* CONFIG_NOBQFMAN */
 542
 543 #ifdef CONFIG_SYS_DPAA_FMAN
 544 #define CONFIG_CORTINA_FW_LENGTH        0x40000
 545 #define RGMII_PHY1_ADDR         0x01  /* RealTek RTL8211E */
 546 #define RGMII_PHY2_ADDR         0x02
 547 #define CORTINA_PHY_ADDR1       0x0c  /* Cortina CS4315 */
 548 #define CORTINA_PHY_ADDR2       0x0d
 549 #define FM1_10GEC3_PHY_ADDR     0x00  /* Aquantia AQ1202 10G Base-T */
 550 #define FM1_10GEC4_PHY_ADDR     0x01
 551 #endif
 552
 553 #ifdef CONFIG_FMAN_ENET
 554 #define CONFIG_ETHPRIME         "FM1@DTSEC3"
 555 #endif
 556
 557 /*
 558  * SATA
 559  */
 560 #ifdef CONFIG_FSL_SATA_V2
 561 #define CONFIG_SYS_SATA_MAX_DEVICE      2
 562 #define CONFIG_SATA1
 563 #define CONFIG_SYS_SATA1                CONFIG_SYS_MPC85xx_SATA1_ADDR
 564 #define CONFIG_SYS_SATA1_FLAGS          FLAGS_DMA
 565 #define CONFIG_SATA2
 566 #define CONFIG_SYS_SATA2                CONFIG_SYS_MPC85xx_SATA2_ADDR
 567 #define CONFIG_SYS_SATA2_FLAGS          FLAGS_DMA
 568 #define CONFIG_LBA48
 569 #endif
 570
 571 /*
 572  * USB
 573  */
 574 #ifdef CONFIG_USB_EHCI_HCD
 575 #define CONFIG_USB_EHCI_FSL
 576 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 577 #define CONFIG_HAS_FSL_DR_USB
 578 #endif
 579
 580 /*
 581  * SDHC
 582  */
 583 #ifdef CONFIG_MMC
 584 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
 585 #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
 586 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
 587 #endif
 588
 589 /*
 590  * Dynamic MTD Partition support with mtdparts
 591  */
 592
 593 /*
 594  * Environment
 595  */
 596
 597 /*
 598  * Miscellaneous configurable options
 599  */
 600 #define CONFIG_SYS_LOAD_ADDR    0x2000000 /* default load address */
 601
 602 /*
 603  * For booting Linux, the board info and command line data
 604  * have to be in the first 64 MB of memory, since this is
 605  * the maximum mapped by the Linux kernel during initialization.
 606  */
 607 #define CONFIG_SYS_BOOTMAPSZ    (64 << 20)      /* Initial map for Linux*/
 608 #define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */
 609
 610 #ifdef CONFIG_CMD_KGDB
 611 #define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port */
 612 #define CONFIG_KGDB_SER_INDEX   2       /* which serial port to use */
 613 #endif
 614
 615 /*
 616  * Environment Configuration
 617  */
 618 #define CONFIG_ROOTPATH  "/opt/nfsroot"
 619 #define CONFIG_BOOTFILE  "uImage"
 620 #define CONFIG_UBOOTPATH "u-boot.bin"   /* U-Boot image on TFTP server */
 621
 622 /* default location for tftp and bootm */
 623 #define CONFIG_LOADADDR         1000000
 624 #define __USB_PHY_TYPE          utmi
 625
 626 #define CONFIG_EXTRA_ENV_SETTINGS                               \
 627         "hwconfig=fsl_ddr:"                                     \
 628         "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) ","      \
 629         "bank_intlv=auto;"                                      \
 630         "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
 631         "netdev=eth0\0"                                         \
 632         "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"             \
 633         "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"     \
 634         "tftpflash=tftpboot $loadaddr $uboot && "               \
 635         "protect off $ubootaddr +$filesize && "                 \
 636         "erase $ubootaddr +$filesize && "                       \
 637         "cp.b $loadaddr $ubootaddr $filesize && "               \
 638         "protect on $ubootaddr +$filesize && "                  \
 639         "cmp.b $loadaddr $ubootaddr $filesize\0"                \
 640         "consoledev=ttyS0\0"                                    \
 641         "ramdiskaddr=2000000\0"                                 \
 642         "ramdiskfile=t2080rdb/ramdisk.uboot\0"                  \
 643         "fdtaddr=1e00000\0"                                     \
 644         "fdtfile=t2080rdb/t2080rdb.dtb\0"                       \
 645         "bdev=sda3\0"
 646
 647 /*
 648  * For emulation this causes u-boot to jump to the start of the
 649  * proof point app code automatically
 650  */
 651 #define CONFIG_PROOF_POINTS                             \
 652         "setenv bootargs root=/dev/$bdev rw "           \
 653         "console=$consoledev,$baudrate $othbootargs;"   \
 654         "cpu 1 release 0x29000000 - - -;"               \
 655         "cpu 2 release 0x29000000 - - -;"               \
 656         "cpu 3 release 0x29000000 - - -;"               \
 657         "cpu 4 release 0x29000000 - - -;"               \
 658         "cpu 5 release 0x29000000 - - -;"               \
 659         "cpu 6 release 0x29000000 - - -;"               \
 660         "cpu 7 release 0x29000000 - - -;"               \
 661         "go 0x29000000"
 662
 663 #define CONFIG_HVBOOT                           \
 664         "setenv bootargs config-addr=0x60000000; "      \
 665         "bootm 0x01000000 - 0x00f00000"
 666
 667 #define CONFIG_ALU                              \
 668         "setenv bootargs root=/dev/$bdev rw "           \
 669         "console=$consoledev,$baudrate $othbootargs;"   \
 670         "cpu 1 release 0x01000000 - - -;"               \
 671         "cpu 2 release 0x01000000 - - -;"               \
 672         "cpu 3 release 0x01000000 - - -;"               \
 673         "cpu 4 release 0x01000000 - - -;"               \
 674         "cpu 5 release 0x01000000 - - -;"               \
 675         "cpu 6 release 0x01000000 - - -;"               \
 676         "cpu 7 release 0x01000000 - - -;"               \
 677         "go 0x01000000"
 678
 679 #define CONFIG_LINUX                            \
 680         "setenv bootargs root=/dev/ram rw "             \
 681         "console=$consoledev,$baudrate $othbootargs;"   \
 682         "setenv ramdiskaddr 0x02000000;"                \
 683         "setenv fdtaddr 0x00c00000;"                    \
 684         "setenv loadaddr 0x1000000;"                    \
 685         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 686
 687 #define CONFIG_HDBOOT                                   \
 688         "setenv bootargs root=/dev/$bdev rw "           \
 689         "console=$consoledev,$baudrate $othbootargs;"   \
 690         "tftp $loadaddr $bootfile;"                     \
 691         "tftp $fdtaddr $fdtfile;"                       \
 692         "bootm $loadaddr - $fdtaddr"
 693
 694 #define CONFIG_NFSBOOTCOMMAND                   \
 695         "setenv bootargs root=/dev/nfs rw "     \
 696         "nfsroot=$serverip:$rootpath "          \
 697         "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 698         "console=$consoledev,$baudrate $othbootargs;"   \
 699         "tftp $loadaddr $bootfile;"             \
 700         "tftp $fdtaddr $fdtfile;"               \
 701         "bootm $loadaddr - $fdtaddr"
 702
 703 #define CONFIG_RAMBOOTCOMMAND                           \
 704         "setenv bootargs root=/dev/ram rw "             \
 705         "console=$consoledev,$baudrate $othbootargs;"   \
 706         "tftp $ramdiskaddr $ramdiskfile;"               \
 707         "tftp $loadaddr $bootfile;"                     \
 708         "tftp $fdtaddr $fdtfile;"                       \
 709         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 710
 711 #define CONFIG_BOOTCOMMAND              CONFIG_LINUX
 712
 713 #include <asm/fsl_secure_boot.h>
 714
 715 #endif  /* __T2080RDB_H */