src/arm64/qcom/pm8150l.dtsi

   1 // SPDX-License-Identifier: BSD-3-Clause
   2 /*
   3  * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved.
   4  * Copyright (c) 2019, Linaro Limited
   5  */
   6
   7 #include <dt-bindings/iio/qcom,spmi-vadc.h>
   8 #include <dt-bindings/interrupt-controller/irq.h>
   9 #include <dt-bindings/spmi/spmi.h>
  10
  11 / {
  12         thermal-zones {
  13                 pm8150l-thermal {
  14                         polling-delay-passive = <100>;
  15                         polling-delay = <0>;
  16
  17                         thermal-sensors = <&pm8150l_temp>;
  18
  19                         trips {
  20                                 trip0 {
  21                                         temperature = <95000>;
  22                                         hysteresis = <0>;
  23                                         type = "passive";
  24                                 };
  25
  26                                 trip1 {
  27                                         temperature = <115000>;
  28                                         hysteresis = <0>;
  29                                         type = "hot";
  30                                 };
  31
  32                                 trip2 {
  33                                         temperature = <145000>;
  34                                         hysteresis = <0>;
  35                                         type = "critical";
  36                                 };
  37                         };
  38                 };
  39         };
  40 };
  41
  42 &spmi_bus {
  43         pmic@4 {
  44                 compatible = "qcom,pm8150l", "qcom,spmi-pmic";
  45                 reg = <0x4 SPMI_USID>;
  46                 #address-cells = <1>;
  47                 #size-cells = <0>;
  48
  49                 pon@800 {
  50                         compatible = "qcom,pm8916-pon";
  51                         reg = <0x0800>;
  52
  53                         status = "disabled";
  54                 };
  55
  56                 pm8150l_temp: temp-alarm@2400 {
  57                         compatible = "qcom,spmi-temp-alarm";
  58                         reg = <0x2400>;
  59                         interrupts = <0x4 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
  60                         io-channels = <&pm8150l_adc ADC5_DIE_TEMP>;
  61                         io-channel-names = "thermal";
  62                         #thermal-sensor-cells = <0>;
  63                 };
  64
  65                 pm8150l_adc: adc@3100 {
  66                         compatible = "qcom,spmi-adc5";
  67                         reg = <0x3100>;
  68                         #address-cells = <1>;
  69                         #size-cells = <0>;
  70                         #io-channel-cells = <1>;
  71                         interrupts = <0x4 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
  72
  73                         channel@0 {
  74                                 reg = <ADC5_REF_GND>;
  75                                 qcom,pre-scaling = <1 1>;
  76                                 label = "ref_gnd";
  77                         };
  78
  79                         channel@1 {
  80                                 reg = <ADC5_1P25VREF>;
  81                                 qcom,pre-scaling = <1 1>;
  82                                 label = "vref_1p25";
  83                         };
  84
  85                         channel@6 {
  86                                 reg = <ADC5_DIE_TEMP>;
  87                                 qcom,pre-scaling = <1 1>;
  88                                 label = "die_temp";
  89                         };
  90                 };
  91
  92                 pm8150l_adc_tm: adc-tm@3500 {
  93                         compatible = "qcom,spmi-adc-tm5";
  94                         reg = <0x3500>;
  95                         interrupts = <0x4 0x35 0x0 IRQ_TYPE_EDGE_RISING>;
  96                         #thermal-sensor-cells = <1>;
  97                         #address-cells = <1>;
  98                         #size-cells = <0>;
  99                         status = "disabled";
 100                 };
 101
 102                 pm8150l_gpios: gpio@c000 {
 103                         compatible = "qcom,pm8150l-gpio", "qcom,spmi-gpio";
 104                         reg = <0xc000>;
 105                         gpio-controller;
 106                         gpio-ranges = <&pm8150l_gpios 0 0 12>;
 107                         #gpio-cells = <2>;
 108                         interrupt-controller;
 109                         #interrupt-cells = <2>;
 110                 };
 111         };
 112
 113         pmic@5 {
 114                 compatible = "qcom,pm8150l", "qcom,spmi-pmic";
 115                 reg = <0x5 SPMI_USID>;
 116                 #address-cells = <1>;
 117                 #size-cells = <0>;
 118
 119                 pm8150l_flash: led-controller@d300 {
 120                         compatible = "qcom,pm8150l-flash-led", "qcom,spmi-flash-led";
 121                         reg = <0xd300>;
 122                         status = "disabled";
 123                 };
 124
 125                 pm8150l_lpg: pwm {
 126                         compatible = "qcom,pm8150l-lpg";
 127
 128                         #address-cells = <1>;
 129                         #size-cells = <0>;
 130                         #pwm-cells = <2>;
 131
 132                         status = "disabled";
 133                 };
 134
 135                 pm8150l_wled: leds@d800 {
 136                         compatible = "qcom,pm8150l-wled";
 137                         reg = <0xd800>, <0xd900>;
 138                         interrupts = <0x5 0xd8 0x1 IRQ_TYPE_EDGE_RISING>,
 139                                      <0x5 0xd8 0x2 IRQ_TYPE_EDGE_RISING>;
 140                         interrupt-names = "ovp", "short";
 141                         label = "backlight";
 142
 143                         status = "disabled";
 144                 };
 145         };
 146 };