board/BuR/brppt2/board.c

   1 // SPDX-License-Identifier: GPL-2.0+
   2 /*
   3  * Board functions for BuR BRPPT2 board
   4  *
   5  * Copyright (C) 2019
   6  * B&R Industrial Automation GmbH - http://www.br-automation.com/
   7  *
   8  */
   9 #include <common.h>
  10 #include <cpu_func.h>
  11 #include <hang.h>
  12 #include <init.h>
  13 #include <spl.h>
  14 #include <dm.h>
  15 #include <miiphy.h>
  16 #include <asm/arch/crm_regs.h>
  17 #include <asm/arch/sys_proto.h>
  18 #include <asm/arch/iomux.h>
  19 #include <asm/arch/mx6-pins.h>
  20 #ifdef CONFIG_SPL_BUILD
  21 # include <asm/arch/mx6-ddr.h>
  22 #endif
  23 #include <asm/arch/clock.h>
  24 #include <asm/global_data.h>
  25 #include <asm/io.h>
  26 #include <asm/gpio.h>
  27
  28 #define USBHUB_RSTN     IMX_GPIO_NR(1, 16)
  29 #define BKLT_EN         IMX_GPIO_NR(1, 15)
  30 #define CAPT_INT        IMX_GPIO_NR(4, 9)
  31 #define CAPT_RESETN     IMX_GPIO_NR(4, 11)
  32 #define SW_INTN         IMX_GPIO_NR(3, 26)
  33 #define VCCDISP_EN      IMX_GPIO_NR(5, 18)
  34 #define EMMC_RSTN       IMX_GPIO_NR(6, 8)
  35 #define PMIC_IRQN       IMX_GPIO_NR(5, 22)
  36 #define TASTER          IMX_GPIO_NR(5, 23)
  37
  38 #define ETH0_LINK       IMX_GPIO_NR(1, 27)
  39 #define ETH1_LINK       IMX_GPIO_NR(1, 28)
  40
  41 #define UART_PAD_CTRL           (PAD_CTL_PUS_47K_UP |                   \
  42                                 PAD_CTL_SPEED_LOW | PAD_CTL_DSE_48ohm | \
  43                                 PAD_CTL_SRE_SLOW  | PAD_CTL_HYS)
  44
  45 #define I2C_PAD_CTRL            (PAD_CTL_PUS_47K_UP |                   \
  46                                 PAD_CTL_SPEED_LOW | PAD_CTL_DSE_48ohm | \
  47                                 PAD_CTL_SRE_SLOW  | PAD_CTL_HYS)
  48
  49 #define ECSPI_PAD_CTRL          (PAD_CTL_PUS_100K_DOWN |                \
  50                                 PAD_CTL_SPEED_MED | PAD_CTL_DSE_48ohm | \
  51                                 PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
  52 #define USDHC_PAD_CTRL          (PAD_CTL_PUS_47K_UP |                   \
  53                                 PAD_CTL_SPEED_LOW | PAD_CTL_DSE_48ohm | \
  54                                 PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
  55
  56 #define ENET_PAD_CTRL           (PAD_CTL_PUS_100K_UP |                  \
  57                                 PAD_CTL_SPEED_MED | PAD_CTL_DSE_60ohm | \
  58                                 PAD_CTL_SRE_SLOW  | PAD_CTL_HYS)
  59
  60 #define ENET_PAD_CTRL1          (PAD_CTL_PUS_100K_UP |                  \
  61                                 PAD_CTL_SPEED_MED | PAD_CTL_DSE_34ohm | \
  62                                 PAD_CTL_SRE_SLOW  | PAD_CTL_HYS)
  63
  64 #define ENET_PAD_CTRL_PU        (PAD_CTL_PUS_100K_UP |          \
  65                                 PAD_CTL_SPEED_MED | PAD_CTL_DSE_80ohm | \
  66                                 PAD_CTL_SRE_SLOW  | PAD_CTL_HYS)
  67
  68 #define ENET_PAD_CTRL_CLK       ((PAD_CTL_PUS_100K_UP & ~PAD_CTL_PKE) | \
  69                                 PAD_CTL_SPEED_MED | PAD_CTL_DSE_60ohm | \
  70                                 PAD_CTL_SRE_FAST)
  71
  72 #define GPIO_PAD_CTRL_PU        (PAD_CTL_PUS_100K_UP |                  \
  73                                 PAD_CTL_SPEED_LOW | PAD_CTL_DSE_48ohm | \
  74                                 PAD_CTL_SRE_SLOW  | PAD_CTL_HYS)
  75
  76 #define GPIO_PAD_CTRL_PD        (PAD_CTL_PUS_100K_DOWN |                \
  77                                 PAD_CTL_SPEED_LOW | PAD_CTL_DSE_48ohm | \
  78                                 PAD_CTL_SRE_SLOW  | PAD_CTL_HYS)
  79
  80 #define LCDCMOS_PAD_CTRL        (PAD_CTL_PUS_100K_DOWN |                \
  81                                 PAD_CTL_SPEED_LOW | PAD_CTL_DSE_120ohm |\
  82                                 PAD_CTL_SRE_SLOW  | PAD_CTL_HYS)
  83
  84 #define MUXDESC(pad, ctrl)      IOMUX_PADS(pad | MUX_PAD_CTRL(ctrl))
  85
  86 #if !defined(CONFIG_SPL_BUILD)
  87 static iomux_v3_cfg_t const eth_pads[] = {
  88         /*
  89          * Gigabit Ethernet
  90          */
  91         /* CLKs */
  92         MUXDESC(PAD_GPIO_16__ENET_REF_CLK,      ENET_PAD_CTRL_CLK),
  93         MUXDESC(PAD_ENET_REF_CLK__ENET_TX_CLK,  ENET_PAD_CTRL_CLK),
  94         /* MDIO */
  95         MUXDESC(PAD_ENET_MDIO__ENET_MDIO,       ENET_PAD_CTRL_PU),
  96         MUXDESC(PAD_ENET_MDC__ENET_MDC,         ENET_PAD_CTRL_PU),
  97         /* RGMII */
  98         MUXDESC(PAD_RGMII_TXC__RGMII_TXC,       ENET_PAD_CTRL1),
  99         MUXDESC(PAD_RGMII_TD0__RGMII_TD0,       ENET_PAD_CTRL),
 100         MUXDESC(PAD_RGMII_TD1__RGMII_TD1,       ENET_PAD_CTRL),
 101         MUXDESC(PAD_RGMII_TD2__RGMII_TD2,       ENET_PAD_CTRL),
 102         MUXDESC(PAD_RGMII_TD3__RGMII_TD3,       ENET_PAD_CTRL),
 103         MUXDESC(PAD_RGMII_TX_CTL__RGMII_TX_CTL, ENET_PAD_CTRL),
 104         MUXDESC(PAD_RGMII_RXC__RGMII_RXC,       ENET_PAD_CTRL_PU),
 105         MUXDESC(PAD_RGMII_RD0__RGMII_RD0,       ENET_PAD_CTRL_PU),
 106         MUXDESC(PAD_RGMII_RD1__RGMII_RD1,       ENET_PAD_CTRL_PU),
 107         MUXDESC(PAD_RGMII_RD2__RGMII_RD2,       ENET_PAD_CTRL_PU),
 108         MUXDESC(PAD_RGMII_RD3__RGMII_RD3,       ENET_PAD_CTRL_PU),
 109         MUXDESC(PAD_RGMII_RX_CTL__RGMII_RX_CTL, ENET_PAD_CTRL_PU),
 110         /* ETH0_LINK */
 111         MUXDESC(PAD_ENET_RXD0__GPIO1_IO27,      GPIO_PAD_CTRL_PD),
 112         /* ETH1_LINK */
 113         MUXDESC(PAD_ENET_TX_EN__GPIO1_IO28,     GPIO_PAD_CTRL_PD),
 114 };
 115
 116 static iomux_v3_cfg_t const board_pads[] = {
 117         /*
 118          * I2C #3, #4
 119          */
 120         MUXDESC(PAD_GPIO_3__I2C3_SCL,           I2C_PAD_CTRL),
 121         MUXDESC(PAD_GPIO_6__I2C3_SDA,           I2C_PAD_CTRL),
 122
 123         /*
 124          * UART#4 PADS
 125          * UART_Tasten
 126          */
 127         MUXDESC(PAD_CSI0_DAT12__UART4_TX_DATA,  UART_PAD_CTRL),
 128         MUXDESC(PAD_CSI0_DAT13__UART4_RX_DATA,  UART_PAD_CTRL),
 129         MUXDESC(PAD_CSI0_DAT17__UART4_CTS_B,    UART_PAD_CTRL),
 130         MUXDESC(PAD_CSI0_DAT16__UART4_RTS_B,    UART_PAD_CTRL),
 131         /*
 132          * ESCPI#1
 133          * M25P32 NOR-Flash
 134          */
 135         MUXDESC(PAD_EIM_D16__ECSPI1_SCLK,       ECSPI_PAD_CTRL),
 136         MUXDESC(PAD_EIM_D17__ECSPI1_MISO,       ECSPI_PAD_CTRL),
 137         MUXDESC(PAD_EIM_D18__ECSPI1_MOSI,       ECSPI_PAD_CTRL),
 138         MUXDESC(PAD_EIM_D19__GPIO3_IO19,        ECSPI_PAD_CTRL),
 139         /*
 140          * ESCPI#2
 141          * resTouch SPI ADC
 142          */
 143         MUXDESC(PAD_CSI0_DAT8__ECSPI2_SCLK,     ECSPI_PAD_CTRL),
 144         MUXDESC(PAD_EIM_OE__ECSPI2_MISO,        ECSPI_PAD_CTRL),
 145         MUXDESC(PAD_CSI0_DAT9__ECSPI2_MOSI,     ECSPI_PAD_CTRL),
 146         MUXDESC(PAD_EIM_D24__GPIO3_IO24,        ECSPI_PAD_CTRL),
 147         /*
 148          * USDHC#4
 149          */
 150         MUXDESC(PAD_SD4_CLK__SD4_CLK,           USDHC_PAD_CTRL),
 151         MUXDESC(PAD_SD4_CMD__SD4_CMD,           USDHC_PAD_CTRL),
 152         MUXDESC(PAD_SD4_DAT0__SD4_DATA0,        USDHC_PAD_CTRL),
 153         MUXDESC(PAD_SD4_DAT1__SD4_DATA1,        USDHC_PAD_CTRL),
 154         MUXDESC(PAD_SD4_DAT2__SD4_DATA2,        USDHC_PAD_CTRL),
 155         MUXDESC(PAD_SD4_DAT3__SD4_DATA3,        USDHC_PAD_CTRL),
 156         MUXDESC(PAD_SD4_DAT4__SD4_DATA4,        USDHC_PAD_CTRL),
 157         MUXDESC(PAD_SD4_DAT5__SD4_DATA5,        USDHC_PAD_CTRL),
 158         MUXDESC(PAD_SD4_DAT6__SD4_DATA6,        USDHC_PAD_CTRL),
 159         MUXDESC(PAD_SD4_DAT7__SD4_DATA7,        USDHC_PAD_CTRL),
 160         /*
 161          * USB OTG power & ID
 162          */
 163         /* USB_OTG_5V_EN */
 164         MUXDESC(PAD_EIM_D22__GPIO3_IO22,        GPIO_PAD_CTRL_PD),
 165         MUXDESC(PAD_EIM_D31__GPIO3_IO31,        GPIO_PAD_CTRL_PD),
 166         /* USB_OTG_JUMPER */
 167         MUXDESC(PAD_ENET_RX_ER__USB_OTG_ID,     GPIO_PAD_CTRL_PD),
 168         /*
 169          * PWM-Pins
 170          */
 171         /* BKLT_CTL */
 172         MUXDESC(PAD_SD1_CMD__PWM4_OUT,          GPIO_PAD_CTRL_PD),
 173         /* SPEAKER */
 174         MUXDESC(PAD_SD1_DAT1__PWM3_OUT,         GPIO_PAD_CTRL_PD),
 175         /*
 176          * GPIOs
 177          */
 178         /* USB_HUB_nRESET */
 179         MUXDESC(PAD_SD1_DAT0__GPIO1_IO16,       GPIO_PAD_CTRL_PD),
 180         /* BKLT_EN */
 181         MUXDESC(PAD_SD2_DAT0__GPIO1_IO15,       GPIO_PAD_CTRL_PD),
 182         /* capTouch_INT */
 183         MUXDESC(PAD_KEY_ROW1__GPIO4_IO09,       GPIO_PAD_CTRL_PD),
 184         /* capTouch_nRESET */
 185         MUXDESC(PAD_KEY_ROW2__GPIO4_IO11,       GPIO_PAD_CTRL_PD),
 186         /* SW_nINT */
 187         MUXDESC(PAD_EIM_D26__GPIO3_IO26,        GPIO_PAD_CTRL_PU),
 188         /* VCC_DISP_EN */
 189         MUXDESC(PAD_CSI0_PIXCLK__GPIO5_IO18,    GPIO_PAD_CTRL_PD),
 190         /* eMMC_nRESET */
 191         MUXDESC(PAD_NANDF_ALE__GPIO6_IO08,      GPIO_PAD_CTRL_PD),
 192         /* HWID*/
 193         MUXDESC(PAD_NANDF_D0__GPIO2_IO00,       GPIO_PAD_CTRL_PU),
 194         MUXDESC(PAD_NANDF_D1__GPIO2_IO01,       GPIO_PAD_CTRL_PU),
 195         MUXDESC(PAD_NANDF_D2__GPIO2_IO02,       GPIO_PAD_CTRL_PU),
 196         MUXDESC(PAD_NANDF_D3__GPIO2_IO03,       GPIO_PAD_CTRL_PU),
 197         /* PMIC_nIRQ */
 198         MUXDESC(PAD_CSI0_DAT4__GPIO5_IO22,      GPIO_PAD_CTRL_PU),
 199         /* nTASTER */
 200         MUXDESC(PAD_CSI0_DAT5__GPIO5_IO23,      GPIO_PAD_CTRL_PU),
 201         /* RGB LCD Display */
 202         MUXDESC(PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK,    LCDCMOS_PAD_CTRL),
 203         MUXDESC(PAD_DI0_PIN2__IPU1_DI0_PIN02,           LCDCMOS_PAD_CTRL),
 204         MUXDESC(PAD_DI0_PIN3__IPU1_DI0_PIN03,           LCDCMOS_PAD_CTRL),
 205         MUXDESC(PAD_DI0_PIN4__IPU1_DI0_PIN04,           LCDCMOS_PAD_CTRL),
 206         MUXDESC(PAD_DI0_PIN15__IPU1_DI0_PIN15,          LCDCMOS_PAD_CTRL),
 207         MUXDESC(PAD_DISP0_DAT0__IPU1_DISP0_DATA00,      LCDCMOS_PAD_CTRL),
 208         MUXDESC(PAD_DISP0_DAT1__IPU1_DISP0_DATA01,      LCDCMOS_PAD_CTRL),
 209         MUXDESC(PAD_DISP0_DAT2__IPU1_DISP0_DATA02,      LCDCMOS_PAD_CTRL),
 210         MUXDESC(PAD_DISP0_DAT3__IPU1_DISP0_DATA03,      LCDCMOS_PAD_CTRL),
 211         MUXDESC(PAD_DISP0_DAT4__IPU1_DISP0_DATA04,      LCDCMOS_PAD_CTRL),
 212         MUXDESC(PAD_DISP0_DAT5__IPU1_DISP0_DATA05,      LCDCMOS_PAD_CTRL),
 213         MUXDESC(PAD_DISP0_DAT6__IPU1_DISP0_DATA06,      LCDCMOS_PAD_CTRL),
 214         MUXDESC(PAD_DISP0_DAT7__IPU1_DISP0_DATA07,      LCDCMOS_PAD_CTRL),
 215         MUXDESC(PAD_DISP0_DAT8__IPU1_DISP0_DATA08,      LCDCMOS_PAD_CTRL),
 216         MUXDESC(PAD_DISP0_DAT9__IPU1_DISP0_DATA09,      LCDCMOS_PAD_CTRL),
 217         MUXDESC(PAD_DISP0_DAT10__IPU1_DISP0_DATA10,     LCDCMOS_PAD_CTRL),
 218         MUXDESC(PAD_DISP0_DAT11__IPU1_DISP0_DATA11,     LCDCMOS_PAD_CTRL),
 219         MUXDESC(PAD_DISP0_DAT12__IPU1_DISP0_DATA12,     LCDCMOS_PAD_CTRL),
 220         MUXDESC(PAD_DISP0_DAT13__IPU1_DISP0_DATA13,     LCDCMOS_PAD_CTRL),
 221         MUXDESC(PAD_DISP0_DAT14__IPU1_DISP0_DATA14,     LCDCMOS_PAD_CTRL),
 222         MUXDESC(PAD_DISP0_DAT15__IPU1_DISP0_DATA15,     LCDCMOS_PAD_CTRL),
 223         MUXDESC(PAD_DISP0_DAT16__IPU1_DISP0_DATA16,     LCDCMOS_PAD_CTRL),
 224         MUXDESC(PAD_DISP0_DAT17__IPU1_DISP0_DATA17,     LCDCMOS_PAD_CTRL),
 225         MUXDESC(PAD_DISP0_DAT18__IPU1_DISP0_DATA18,     LCDCMOS_PAD_CTRL),
 226         MUXDESC(PAD_DISP0_DAT19__IPU1_DISP0_DATA19,     LCDCMOS_PAD_CTRL),
 227         MUXDESC(PAD_DISP0_DAT20__IPU1_DISP0_DATA20,     LCDCMOS_PAD_CTRL),
 228         MUXDESC(PAD_DISP0_DAT21__IPU1_DISP0_DATA21,     LCDCMOS_PAD_CTRL),
 229         MUXDESC(PAD_DISP0_DAT22__IPU1_DISP0_DATA22,     LCDCMOS_PAD_CTRL),
 230         MUXDESC(PAD_DISP0_DAT23__IPU1_DISP0_DATA23,     LCDCMOS_PAD_CTRL),
 231 };
 232
 233 int board_ehci_hcd_init(int port)
 234 {
 235         gpio_direction_output(USBHUB_RSTN, 1);
 236
 237         return 0;
 238 }
 239
 240 int board_late_init(void)
 241 {
 242         ulong b_mode = 4;
 243
 244         if (gpio_get_value(TASTER) == 0)
 245                 b_mode = 12;
 246
 247         env_set_ulong("b_mode", b_mode);
 248
 249         return 0;
 250 }
 251
 252 int board_init(void)
 253 {
 254         gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
 255
 256         if (gpio_request(BKLT_EN, "BKLT_EN"))
 257                 printf("Warning: BKLT_EN setup failed\n");
 258         gpio_direction_output(BKLT_EN, 0);
 259
 260         if (gpio_request(USBHUB_RSTN, "USBHUB_nRST"))
 261                 printf("Warning: USBHUB_nRST setup failed\n");
 262         gpio_direction_output(USBHUB_RSTN, 0);
 263
 264         if (gpio_request(TASTER, "TASTER"))
 265                 printf("Warning: TASTER setup failed\n");
 266         gpio_direction_input(TASTER);
 267
 268         return 0;
 269 }
 270
 271 int board_early_init_f(void)
 272 {
 273         struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
 274
 275         SETUP_IOMUX_PADS(board_pads);
 276         SETUP_IOMUX_PADS(eth_pads);
 277
 278         /* set GPIO_16 as ENET_REF_CLK_OUT running at 25 MHz */
 279         setbits_le32(&iomux->gpr[1], IOMUXC_GPR1_ENET_CLK_SEL_MASK);
 280         enable_fec_anatop_clock(0, ENET_25MHZ);
 281         enable_enet_clk(1);
 282
 283         return 0;
 284 }
 285
 286 int dram_init(void)
 287 {
 288         gd->ram_size = imx_ddr_size();
 289
 290         return 0;
 291 }
 292 #else
 293 /* configure MX6SOLO/DUALLITE mmdc DDR io registers */
 294 static struct mx6sdl_iomux_ddr_regs ddr_iomux_s = {
 295         /* SDCLK[0:1], CAS, RAS, Reset: Differential input, 40ohm */
 296         .dram_sdclk_0           = 0x00020030,
 297         .dram_sdclk_1           = 0x00020030,
 298         .dram_cas               = 0x00020030,
 299         .dram_ras               = 0x00020030,
 300         .dram_reset             = 0x00020030,
 301         /* SDCKE[0:1]: 100k pull-up */
 302         .dram_sdcke0            = 0x00003000,
 303         .dram_sdcke1            = 0x00003000,
 304         /* SDBA2: pull-up disabled */
 305         .dram_sdba2             = 0x00000000,
 306         /* SDODT[0:1]: 100k pull-up, 40 ohm */
 307         .dram_sdodt0            = 0x00003030,
 308         .dram_sdodt1            = 0x00003030,
 309         /* SDQS[0:7]: Differential input, 40 ohm */
 310         .dram_sdqs0             = 0x00000030,
 311         .dram_sdqs1             = 0x00000030,
 312         .dram_sdqs2             = 0x00000030,
 313         .dram_sdqs3             = 0x00000030,
 314         .dram_sdqs4             = 0x00000030,
 315         .dram_sdqs5             = 0x00000030,
 316         .dram_sdqs6             = 0x00000030,
 317         .dram_sdqs7             = 0x00000030,
 318         /* DQM[0:7]: Differential input, 40 ohm */
 319         .dram_dqm0              = 0x00020030,
 320         .dram_dqm1              = 0x00020030,
 321         .dram_dqm2              = 0x00020030,
 322         .dram_dqm3              = 0x00020030,
 323         .dram_dqm4              = 0x00020030,
 324         .dram_dqm5              = 0x00020030,
 325         .dram_dqm6              = 0x00020030,
 326         .dram_dqm7              = 0x00020030,
 327 };
 328
 329 /* configure MX6SOLO/DUALLITE mmdc GRP io registers */
 330 static struct mx6sdl_iomux_grp_regs grp_iomux_s = {
 331         /* DDR3 */
 332         .grp_ddr_type           = 0x000c0000,
 333         .grp_ddrmode_ctl        = 0x00020000,
 334         /* disable DDR pullups */
 335         .grp_ddrpke             = 0x00000000,
 336         /* ADDR[00:16], SDBA[0:1]: 40 ohm */
 337         .grp_addds              = 0x00000030,
 338         /* CS0/CS1/SDBA2/CKE0/CKE1/SDWE: 40 ohm */
 339         .grp_ctlds              = 0x00000030,
 340         /* DATA[00:63]: Differential input, 40 ohm */
 341         .grp_ddrmode            = 0x00020000,
 342         .grp_b0ds               = 0x00000030,
 343         .grp_b1ds               = 0x00000030,
 344         .grp_b2ds               = 0x00000030,
 345         .grp_b3ds               = 0x00000030,
 346         .grp_b4ds               = 0x00000030,
 347         .grp_b5ds               = 0x00000030,
 348         .grp_b6ds               = 0x00000030,
 349         .grp_b7ds               = 0x00000030,
 350 };
 351
 352 /*
 353  * DDR3 desriptions - these are the memory chips we support
 354  */
 355
 356 /* NT5CC128M16FP-DII */
 357 static struct mx6_ddr3_cfg cfg_nt5cc128m16fp_dii = {
 358         .mem_speed      = 1600,
 359         .density        = 2,
 360         .width          = 16,
 361         .banks          = 8,
 362         .rowaddr        = 14,
 363         .coladdr        = 10,
 364         .pagesz         = 2,
 365         .trcd           = 1375,
 366         .trcmin         = 4875,
 367         .trasmin        = 3500,
 368 };
 369
 370 /* measured on board TSERIES_ARM/1 V_LVDS_DL64 */
 371 static struct mx6_mmdc_calibration cal_nt5cc128m16fp_dii_128x64_s = {
 372         /* write leveling calibration determine, MR1-value = 0x0002 */
 373         .p0_mpwldectrl0 = 0x003F003E,
 374         .p0_mpwldectrl1 = 0x003A003A,
 375         .p1_mpwldectrl0 = 0x001B001C,
 376         .p1_mpwldectrl1 = 0x00190031,
 377         /* Read DQS Gating calibration */
 378         .p0_mpdgctrl0   = 0x02640264,
 379         .p0_mpdgctrl1   = 0x02440250,
 380         .p1_mpdgctrl0   = 0x02400250,
 381         .p1_mpdgctrl1   = 0x0238023C,
 382         /* Read Calibration: DQS delay relative to DQ read access */
 383         .p0_mprddlctl   = 0x40464644,
 384         .p1_mprddlctl   = 0x464A4842,
 385         /* Write Calibration: DQ/DM delay relative to DQS write access */
 386         .p0_mpwrdlctl   = 0x38343034,
 387         .p1_mpwrdlctl   = 0x36323830,
 388 };
 389
 390 /* measured on board TSERIES_ARM/1 V_LVDS_S32 */
 391 static struct mx6_mmdc_calibration cal_nt5cc128m16fp_dii_128x32_s = {
 392         /* write leveling calibration determine, MR1-value = 0x0002 */
 393         .p0_mpwldectrl0 = 0x00410043,
 394         .p0_mpwldectrl1 = 0x003A003C,
 395         /* Read DQS Gating calibration */
 396         .p0_mpdgctrl0   = 0x023C0244,
 397         .p0_mpdgctrl1   = 0x02240230,
 398         /* Read Calibration: DQS delay relative to DQ read access */
 399         .p0_mprddlctl   = 0x484C4A48,
 400         /* Write Calibration: DQ/DM delay relative to DQS write access */
 401         .p0_mpwrdlctl   = 0x3C363434,
 402 };
 403
 404 static void spl_dram_init(void)
 405 {
 406         struct gpio_regs *gpio = (struct gpio_regs *)GPIO2_BASE_ADDR;
 407         u32 val, dram_strap = 0;
 408         struct mx6_ddr3_cfg *mem = NULL;
 409         struct mx6_mmdc_calibration *calib = NULL;
 410         struct mx6_ddr_sysinfo sysinfo = {
 411                 /* width of data bus:0=16,1=32,2=64 */
 412                 .dsize          = -1,   /* CPU type specific (overwritten) */
 413                 /* config for full 4GB range so that get_mem_size() works */
 414                 .cs_density     = 32,   /* 32Gb per CS */
 415                 .ncs            = 1,    /* single chip select */
 416                 .cs1_mirror     = 0,
 417                 .rtt_wr         = 1,    /* DDR3_RTT_60_OHM, RTT_Wr = RZQ/4 */
 418                 .rtt_nom        = 1,    /* DDR3_RTT_60_OHM, RTT_Nom = RZQ/4 */
 419                 .walat          = 1,    /* Write additional latency */
 420                 .ralat          = 5,    /* Read additional latency */
 421                 .mif3_mode      = 3,    /* Command prediction working mode */
 422                 .bi_on          = 1,    /* Bank interleaving enabled */
 423                 .sde_to_rst     = 0x10, /* 14 cycles, 200us (JEDEC default) */
 424                 .rst_to_cke     = 0x23, /* 33 cycles, 500us (JEDEC default) */
 425                 .ddr_type       = 0,    /* DDR3 */
 426         };
 427
 428         /*
 429          * MMDC Calibration requires the following data:
 430          *  mx6_mmdc_calibration - board-specific calibration (routing delays)
 431          *     these calibration values depend on board routing, SoC, and DDR
 432          *  mx6_ddr_sysinfo - board-specific memory architecture (width/cs/etc)
 433          *  mx6_ddr_cfg - chip specific timing/layout details
 434          */
 435
 436         /* setup HWID3-2 to input */
 437         val = readl(&gpio->gpio_dir);
 438         val &= ~(0x1 << 0 | 0x1 << 1);
 439         writel(val, &gpio->gpio_dir);
 440
 441         /* read DRAM strapping from HWID3/2 (bit 1 and bit 0) */
 442         dram_strap = readl(&gpio->gpio_psr) & 0x3;
 443
 444         switch (dram_strap) {
 445         /* 1 GiB, 64 bit, 4 NT5CC128M16FP chips */
 446         case 0:
 447                 puts("DRAM strap 00\n");
 448                 mem = &cfg_nt5cc128m16fp_dii;
 449                 sysinfo.dsize = 2;
 450                 calib = &cal_nt5cc128m16fp_dii_128x64_s;
 451                 break;
 452         /* 512 MiB, 32 bit, 2 NT5CC128M16FP chips */
 453         case 1:
 454                 puts("DRAM strap 01\n");
 455                 mem = &cfg_nt5cc128m16fp_dii;
 456                 sysinfo.dsize = 1;
 457                 calib = &cal_nt5cc128m16fp_dii_128x32_s;
 458                 break;
 459         default:
 460                 printf("DRAM strap 0x%x (invalid)\n", dram_strap);
 461                 break;
 462         }
 463
 464         if (!mem) {
 465                 puts("Error: Invalid Memory Configuration\n");
 466                 hang();
 467         }
 468         if (!calib) {
 469                 puts("Error: Invalid Board Calibration Configuration\n");
 470                 hang();
 471         }
 472
 473         mx6sdl_dram_iocfg(16 << sysinfo.dsize,
 474                           &ddr_iomux_s,
 475                           &grp_iomux_s);
 476
 477         mx6_dram_cfg(&sysinfo, calib, mem);
 478 }
 479
 480 static iomux_v3_cfg_t const board_pads_spl[] = {
 481         /* UART#1 PADS */
 482         MUXDESC(PAD_CSI0_DAT10__UART1_TX_DATA,  UART_PAD_CTRL),
 483         MUXDESC(PAD_CSI0_DAT11__UART1_RX_DATA,  UART_PAD_CTRL),
 484         /* ESCPI#1 PADS */
 485         MUXDESC(PAD_EIM_D16__ECSPI1_SCLK,       ECSPI_PAD_CTRL),
 486         MUXDESC(PAD_EIM_D17__ECSPI1_MISO,       ECSPI_PAD_CTRL),
 487         MUXDESC(PAD_EIM_D18__ECSPI1_MOSI,       ECSPI_PAD_CTRL),
 488         MUXDESC(PAD_EIM_D19__GPIO3_IO19,        ECSPI_PAD_CTRL),
 489         /* USDHC#4 PADS */
 490         MUXDESC(PAD_SD4_CLK__SD4_CLK,           USDHC_PAD_CTRL),
 491         MUXDESC(PAD_SD4_CMD__SD4_CMD,           USDHC_PAD_CTRL),
 492         MUXDESC(PAD_SD4_DAT0__SD4_DATA0,        USDHC_PAD_CTRL),
 493         MUXDESC(PAD_SD4_DAT1__SD4_DATA1,        USDHC_PAD_CTRL),
 494         MUXDESC(PAD_SD4_DAT2__SD4_DATA2,        USDHC_PAD_CTRL),
 495         MUXDESC(PAD_SD4_DAT3__SD4_DATA3,        USDHC_PAD_CTRL),
 496         MUXDESC(PAD_SD4_DAT4__SD4_DATA4,        USDHC_PAD_CTRL),
 497         MUXDESC(PAD_SD4_DAT5__SD4_DATA5,        USDHC_PAD_CTRL),
 498         MUXDESC(PAD_SD4_DAT6__SD4_DATA6,        USDHC_PAD_CTRL),
 499         MUXDESC(PAD_SD4_DAT7__SD4_DATA7,        USDHC_PAD_CTRL),
 500         /* HWID*/
 501         MUXDESC(PAD_NANDF_D0__GPIO2_IO00,       GPIO_PAD_CTRL_PU),
 502         MUXDESC(PAD_NANDF_D1__GPIO2_IO01,       GPIO_PAD_CTRL_PU),
 503         MUXDESC(PAD_NANDF_D2__GPIO2_IO02,       GPIO_PAD_CTRL_PU),
 504         MUXDESC(PAD_NANDF_D3__GPIO2_IO03,       GPIO_PAD_CTRL_PU),
 505 };
 506
 507 void spl_board_init(void)
 508 {
 509         preloader_console_init();
 510 }
 511
 512 static void ccgr_init(void)
 513 {
 514         struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
 515
 516         /*
 517          * We don't use DMA in SPL, but we do need it in U-Boot. U-Boot
 518          * initializes DMA very early (before all board code), so the only
 519          * opportunity we have to initialize APBHDMA clocks is in SPL.
 520          * setbits_le32(&ccm->CCGR0, MXC_CCM_CCGR0_APBHDMA_MASK);
 521          */
 522
 523         writel(0x00C03F3F, &ccm->CCGR0);
 524         writel(0x00F0FC03, &ccm->CCGR1);
 525         writel(0x0FFFF000, &ccm->CCGR2);
 526         writel(0x3FF00000, &ccm->CCGR3);
 527         writel(0x00FFF300, &ccm->CCGR4);
 528         writel(0x0F0030C3, &ccm->CCGR5);
 529         writel(0x000003F0, &ccm->CCGR6);
 530 }
 531
 532 void board_init_f(ulong dummy)
 533 {
 534         ccgr_init();
 535         arch_cpu_init();
 536         timer_init();
 537         gpr_init();
 538
 539         SETUP_IOMUX_PADS(board_pads_spl);
 540         spl_dram_init();
 541 }
 542
 543 void reset_cpu(void)
 544 {
 545 }
 546 #endif /* CONFIG_SPL_BUILD */