Max Filippov [Mon, 5 Sep 2011 23:55:52 +0000 (03:55 +0400)]
target-xtensa: add gdb support
Specific xtensa processor overlay for GDB contains register map in
the gdb/xtensa-config.c. This description is used by the GDB to e.g.
parse 'g' response packets and it may be reused in the qemu's gdbstub
(only XTREG definitions for non-pseudoregisters are needed).
Currently mainline GDB does not support operations with privileged SRs
(see http://sourceware.org/ml/gdb/2011-07/msg00075.html). This support
may be enabled, see NUM_CORE_REGS comment in the gdbstub.c
Max Filippov [Mon, 5 Sep 2011 23:55:49 +0000 (03:55 +0400)]
target-xtensa: implement accurate window check
See ISA, 4.7.1.3 for details.
Window check is inserted before commands that push "used register
watermark" beyond its current level. Used register watermark is reset on
instructions that change WINDOW_BASE/WINDOW_START SRs.
Max Filippov [Mon, 5 Sep 2011 23:55:47 +0000 (03:55 +0400)]
target-xtensa: implement SIMCALL
Tensilica iss provides support for applications running in freestanding
environment through SIMCALL command. It is used by Tensilica libc to
access argc/argv, for file I/O, etc.
Note that simcalls that accept buffer addresses expect virtual addresses.
Max Filippov [Mon, 5 Sep 2011 23:55:44 +0000 (03:55 +0400)]
target-xtensa: implement loop option
See ISA, 4.3.2 for details.
Operations that change LEND SR value invalidate TBs at the old and at
the new LEND. LEND value at TB compilation time is considered constant
and loop instruction is generated based on this value.
Invalidation may be avoided for the TB at the old LEND address, since
looping code verifies actual LEND value.
Invalidation may be avoided for the TB at the new LEND address if
there's a way to associate LEND address with TB at compilation time and
later verify that it doesn't change.
Max Filippov [Mon, 5 Sep 2011 23:55:43 +0000 (03:55 +0400)]
target-xtensa: implement windowed registers
See ISA, 4.7.1 for details.
Physical registers and currently visible window are separate fields in
CPUEnv. Only current window is accessible to TCG. On operations that
change window base helpers copy current window to and from physical
registers.
Window overflow check described in 4.7.1.3 is in separate patch.
Max Filippov [Mon, 5 Sep 2011 23:55:39 +0000 (03:55 +0400)]
target-xtensa: implement CACHE group
All operations in this group are no-ops, because cache ought to be
transparent to applications. However cache may be abused, then we'll
need to actually implement these opcodes.
Max Filippov [Mon, 5 Sep 2011 23:55:31 +0000 (03:55 +0400)]
target-xtensa: implement conditional jumps
- BZ (comparison to zero);
- BI0 (comparison to signed immediate);
- BI1 (comparison to unsigned immediate);
- B (two registers comparison, bit sets comparison);
- BEQZ.N/BNEZ.N (narrow comparison to zero).
Blue Swirl [Sun, 4 Sep 2011 11:32:23 +0000 (11:32 +0000)]
Sparc64: remove useless variable
Remove a useless variable, spotted by clang analyzer:
/src/qemu/target-sparc/op_helper.c:3904:18: warning: unused variable 'tmp' [-Wunused-variable]
target_ulong tmp = val;
The error message is actually incorrect since the variable is used.
Blue Swirl [Sun, 4 Sep 2011 11:22:31 +0000 (11:22 +0000)]
lsi53c895a: avoid a warning from clang analyzer
Avoid this warning from clang analyzer by deleting the variable:
/src/qemu/hw/lsi53c895a.c:895:5: warning: Value stored to 'id' is never read
id = (current_tag >> 8) & 0xf;
Blue Swirl [Sun, 4 Sep 2011 11:03:52 +0000 (11:03 +0000)]
kvm: remove unnecessary assignments
Avoid these warnings from clang analyzer:
/src/qemu/target-i386/kvm.c:772:5: warning: Value stored to 'cwd' is never read
cwd = swd = twd = 0;
/src/qemu/target-i386/kvm.c:772:11: warning: Although the value stored to 'swd' is used in the enclosing expression, the value is never actually read from 'swd'
cwd = swd = twd = 0;
Blue Swirl [Sun, 4 Sep 2011 10:38:01 +0000 (10:38 +0000)]
qemu-io: remove unnecessary assignment
Remove an unnecessary assignment, spotted by clang analyzer:
/src/qemu/qemu-io.c:995:9: warning: Value stored to 'offset' is never read
offset += reqs[i].qiov->size;
Michael Roth [Wed, 7 Sep 2011 23:40:51 +0000 (18:40 -0500)]
build: fix missing trace dep on GENERATED_HEADERS
fc764105 added an include for qemu-common.h to trace/control.h, which
made all users of this header file dependent on GENERATED_HEADERS. Since
it's used by pretty much all the trace backends now, make trace-obj-y
dependent on GENERATED_HEADERS.
Avoid using deprecated gnutls functions with recent gnutls versions.
Fixes build failure on Fedora 16. Keep the old way for compatibility
with old installations such as RHEL-5 (gnutls 1.4.x).
Avi Kivity [Mon, 5 Sep 2011 08:07:05 +0000 (11:07 +0300)]
qemu_vmalloc: align properly for transparent hugepages and KVM
To make good use of transparent hugepages, KVM requires that guest-physical
and host-virtual addresses share the low 21 bits (as opposed to just the low
12 bits normally required).
Adjust qemu_vmalloc() to honor that requirement. Ignore it for small regions
to avoid fragmentation.
Qemu currently assumes that chtype is typedef'd to unsigned long, but
this is not necessarily the case (ncurses, for instance, can configure
this at build-time). This patch uses the predefined chtype if qemu is
configured for curses support and falls back to unsigned long otherwise.
Amit Shah [Fri, 9 Sep 2011 09:00:40 +0000 (14:30 +0530)]
virtio-balloon: Disassociate from the balloon handlers on unplug
Adding a 2nd balloon device after unplugging the first one doesn't work.
Also, the 'info balloon' command should indicate an error mentioning no
balloon device is registered after unplug.
Reproduction steps given by Shaolong Hu:
(qemu) info balloon
Device 'balloon' has not been activated by the guest
(qemu) device_add virtio-balloon-pci,id=balloon1
(qemu) info balloon
balloon: actual=4096
(qemu) balloon 2048
(qemu) info balloon
balloon: actual=2048
(qemu) device_del balloon1
(qemu) info balloon
balloon: actual=4096
(qemu) balloon 2048
(qemu) info balloon
balloon: actual=4096
(qemu) device_del balloon1
Device 'balloon1' not found
(qemu) device_add virtio-balloon-pci,id=balloon1
Another balloon device already registered
Device 'virtio-balloon-pci' could not be initialized
(qemu) device_add virtio-balloon-pci,id=balloon2
Another balloon device already registered
Device 'virtio-balloon-pci' could not be initialized
Thomas Huth [Fri, 9 Sep 2011 05:58:37 +0000 (15:58 +1000)]
tcg/ppc64: Fix zero extension code generation bug for ppc64 host
The ppc64 code generation backend uses an rldicr (Rotate Left Double
Immediate and Clear Right) instruction to implement zero extension of
a 32 bit quantity to a 64 bit quantity (INDEX_op_ext32u_i64). However
this is wrong - this instruction clears specified low bits of the
value, instead of high bits as we require for a zero extension. It
should instead use an rldicl (Rotate Left Double Immediate and Clear
Left) instruction.
Presumably amongst other things, this causes the SLOF firmware image
used with -M pseries to not boot on a ppc64 host.
It appears this bug was exposed by commit 0bf1dbdcc935dfc220a93cd990e947e90706aec6 (tcg/ppc64: fix 16/32 mixup)
which enabled the use of the op_ext32u_i64 operation on the ppc64
backend.
Anthony PERARD [Fri, 9 Sep 2011 12:50:18 +0000 (12:50 +0000)]
xen-mapcache: Fix rlimit set size.
Previously, the address space soft limit was set mcache_max_size. So,
before the mcache_max_size was reached by the mapcache, QEMU was killed
for overuse of the virtual address space.
This patch fix that by setting the soft limit the maximum than can have
QEMU. So the soft and hard limit are always set to RLIM_INFINITY if QEMU
is privileged.
In case QEMU is not run as root and the limit is too low, the maximum
mapcache size will be set the rlim_max - 80MB because observed that QEMU
use 75MB more than the maximum mapcache size after several empirical
tests.
John Haxby [Fri, 17 Jun 2011 12:16:00 +0000 (12:16 +0000)]
Move the xenfb pointer handler to the connected method
Ensure that we read "request-abs-pointer" after the frontend has written
it. This means that we will correctly set up an ansolute or relative
pointer handler correctly.
John Haxby [Fri, 17 Jun 2011 12:15:35 +0000 (12:15 +0000)]
Introduce a new 'connected' xendev op called when Connected.
Rename the existing xendev 'connect' op to 'initialised' and introduce
a new 'connected' op. This new op, if defined, is called when the
backend is connected. Note that since there is no state transition this
may be called more than once.
Stefan Weil [Thu, 8 Sep 2011 15:55:32 +0000 (17:55 +0200)]
Fix include statements for qemu-common.h
* qemu-common.h is not a system include file, so it should be included
with "" instead of <>. Otherwise incremental builds might fail
because only local include files are checked for changes.
target-i386: Compute all flag data inside %cl != 0 test.
The (x << (cl - 1)) quantity is only used if CL != 0. Move the
computation of that quantity nearer its use.
This avoids the creation of undefined TCG operations when the
constant propagation optimization proves that CL == 0, and thus
CL-1 is outside the range [0-wordsize).
Juha Riihimäki [Wed, 31 Aug 2011 20:49:41 +0000 (21:49 +0100)]
usb-musb: Add reset function
Add a separate reset function musb_reset() to the usb-musb interface,
so that users who implement a reset function can also reset usb-musb.
Use this in tusb6010.
Signed-off-by: Juha Riihimäki <[email protected]>
[Riku Voipio: Fixes and restructuring patchset] Signed-off-by: Riku Voipio <[email protected]>
[Peter Maydell: More fixes and cleanups for upstream submission] Signed-off-by: Peter Maydell <[email protected]> Signed-off-by: Gerd Hoffmann <[email protected]>
Peter Maydell [Wed, 31 Aug 2011 20:49:40 +0000 (21:49 +0100)]
usb-musb: Take a DeviceState* in init function
Initialise usb-musb by passing it a DeviceState* and the offset of the
IRQs in its gpio array, rather than a plain pointer to an irq array.
This is simpler for callers and also allows us to pass in a valid parent
to usb_bus_new(), so the USB bus actually appears in the qdev tree.
This patch makes qemu assign a port when creating the device, not when
attaching it. For most usb devices this isn't a noticable difference
because they are in attached state all the time.
The change affects usb-host devices which live in detached state while
the real device is unplugged from the host. They have a fixed port
assigned all the time now instead of getting grabbing one on attach and
releasing it at detach, i.e. they stop floating around at the usb bus.
The change also allows to simplify usb-hub. It doesn't need the
handle_attach() callback any more to configure the downstream ports.
This can be done at device initialitation time now. The changed
initialization order (first grab upstream port, then register downstream
ports) also fixes some icky corner cases. For example it is not possible
any more to plug the hub into one of its own downstream ports.
The usb host adapters must care too. USBPort->dev being non-NULL
doesn't imply any more the device is in attached state. The host
adapters must additionally check the USBPort->dev->attached flag.
Gerd Hoffmann [Fri, 26 Aug 2011 12:13:48 +0000 (14:13 +0200)]
usb-ehci: handle siTDs
This patch adds code to do minimal siTD handling, which is basically
just following the next pointer. This is good enougth to handle the
inactive siTDs used by FreeBSD. Active siTDs are skipped too as we
don't have split transfer support in qemu, additionally a warning is
printed.
Gerd Hoffmann [Fri, 26 Aug 2011 14:27:41 +0000 (16:27 +0200)]
usb-host: endpoint table fixup
USB Devices can have up to 15 IN and 15 OUT endpoints, not 15 endpoints
total. Move from one array to two arrays (one IN, one OUT) to maintain
the endpoint state.
Gerd Hoffmann [Wed, 24 Aug 2011 11:34:17 +0000 (13:34 +0200)]
usb-host: claim port
When configured to pass through a specific host port (using hostbus and
hostport properties), try to claim the port if supported by the kernel.
That will avoid any kernel drivers binding to devices plugged into that
port. It will not stop any userspace apps (such as usb_modeswitch)
access the device via usbfs though.
Gerd Hoffmann [Wed, 24 Aug 2011 12:45:07 +0000 (14:45 +0200)]
usb-host: fix configuration tracking.
It is perfectly fine to leave the usb device in unconfigured state
(USBHostDevice->configuration == 0). Just do that and wait for the
guest to explicitly set a configuration. This is closer to what real
hardware does and it also simplifies the device initialization. There
is no need to figure how the device is configured on the host.
Gerd Hoffmann [Wed, 24 Aug 2011 11:45:06 +0000 (13:45 +0200)]
usb-host: limit open retries
Limit the number of times qemu tries to open host devices to three.
Reset error counter when the device goes away, after un-plugging and
re-plugging the device qemu will try again three times.
Gerd Hoffmann [Wed, 24 Aug 2011 08:55:40 +0000 (10:55 +0200)]
usb-host: fix halted endpoints
Two fixes for the price of one ;)
First, reinitialize the endpoint table after device reset.
This is needed anyway as the reset might have switched interfaces.
It also clears the endpoint halted state.
Second the CLEAR_HALT ioctl wants a unsigned int passed in as
argument, not uint8_t.
This gets my usb sd card reader (sandisk micromate) going.
Gerd Hoffmann [Mon, 22 Aug 2011 12:13:20 +0000 (14:13 +0200)]
usb-host: start tracing support
Add a bunch of trace points to usb-linux.c Drop a bunch of DPRINTK's in
favor of the trace points. Also cleanup error reporting a bit while being
at it.
spice: set qxl->ssd.running=true before telling spice to start, RHBZ #733993
If qxl->ssd.running=true is set after telling spice to start, the spice server
thread can call qxl_send_events while qxl->ssd.running is still false. This leads to
assert(d->ssd.running).
qxl: send interrupt after migration in case ram->int_pending != 0, RHBZ #732949
if qxl_send_events was called from spice server context, and then
migration had completed before a call to pipe_read, the target
guest qxl driver didn't get the interrupt. In addition,
qxl_send_events ignored further interrupts of the same kind, since
ram->int_pending was set. As a result, the guest driver was stacked
or very slow (when the waiting for the interrupt was with timeout).
projects / qemu.git / log