Eugene Shatokhin [Mon, 24 Aug 2015 20:13:42 +0000 (23:13 +0300)]
usbnet: Get EVENT_NO_RUNTIME_PM bit before it is cleared
It is needed to check EVENT_NO_RUNTIME_PM bit of dev->flags in
usbnet_stop(), but its value should be read before it is cleared
when dev->flags is set to 0.
The problem was spotted and the fix was provided by
Oliver Neukum <[email protected]>.
Linus Torvalds [Wed, 26 Aug 2015 00:26:00 +0000 (17:26 -0700)]
Merge branch 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull nvdimm fix from Dan Williams:
"A single fix for status register read size in the nd_blk driver.
The effect of getting the width of this register read wrong is that
all I/O fails when the read returns non-zero. Given the availability
of ACPI 6 NFIT enabled platforms, this could reasonably wait to come
in during the 4.3 merge window with a tag for 4.2-stable. Otherwise,
this makes the 4.2 kernel fully functional with devices that conform
to the mmio-block-apertures defined in the ACPI 6 NFIT (NVDIMM
Firmware Interface Table)"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
nfit, nd_blk: BLK status register is only 32 bits
WANG Cong [Tue, 25 Aug 2015 23:38:12 +0000 (16:38 -0700)]
cls_u32: complete the check for non-forced case in u32_destroy()
In commit 1e052be69d04 ("net_sched: destroy proto tp when all filters are gone")
I added a check in u32_destroy() to see if all real filters are gone
for each tp, however, that is only done for root_ht, same is needed
for others.
This can be reproduced by the following tc commands:
tc filter add dev eth0 parent 1:0 prio 5 handle 15: protocol ip u32 divisor 256
tc filter add dev eth0 protocol ip parent 1: prio 5 handle 15:2:2 u32
ht 15:2: match ip src 10.0.0.2 flowid 1:10
tc filter add dev eth0 protocol ip parent 1: prio 5 handle 15:2:3 u32
ht 15:2: match ip src 10.0.0.3 flowid 1:10
David S. Miller [Wed, 26 Aug 2015 00:01:33 +0000 (17:01 -0700)]
Merge branch 'dsa-docs'
Florian Fainelli says:
====================
Documentation: dsa
This patch series adds some documentation about DSA as a subsystem as well
as the SF2 driver since it slightly diverges from your average DSA driver ;)
====================
Jan Beulich [Mon, 24 Aug 2015 12:22:25 +0000 (06:22 -0600)]
LSM: restore certain default error codes
While in most cases commit b1d9e6b064 ("LSM: Switch to lists of hooks")
retained previous error returns, in three cases it altered them without
any explanation in the commit message. Restore all of them - in the
security_old_inode_init_security() case this led to reiserfs using
uninitialized data, sooner or later crashing the system (the only other
user of this function - ocfs2 - was unaffected afaict, since it passes
pre-initialized structures).
Russell King [Tue, 25 Aug 2015 08:49:53 +0000 (09:49 +0100)]
net: fec: use reinit_completion() in mdio accessor functions
Rather than re-initialising the entire completion on every mdio access,
use reinit_completion() which only resets the completion count. This
avoids possible reinitialisation of the contained spinlock and waitqueue
while they may be in use (eg, mid-completion.)
Such an event could occur if there's a long delay in interrupt handling
causing the mdio accessor to time out, then a second access comes in
while the interrupt handler on a different CPU has called complete().
Another scenario where this has been observed is while locking has
been missing at the phy layer, allowing concurrent attempts to access
the MDIO bus.
Russell King [Tue, 25 Aug 2015 08:49:47 +0000 (09:49 +0100)]
net: phy: add locking to phy_read_mmd_indirect()/phy_write_mmd_indirect()
The phy layer is missing locking for the above two functions - it
has been observed that two threads (userspace and the phy worker
thread) can race, entering the bus ->write or ->read functions
simultaneously.
This causes the FEC driver to initialise a completion while another
thread is waiting on it or while the interrupt is calling complete()
on it, which causes spinlock unlock-without-lock, spinlock lockups,
and completion timeouts.
Fixes: a59a4d192 ("phy: add the EEE support and the way to access to the MMD registers.") Fixes: 0c1d77dfb ("net: libphy: Add phy specific function to access mmd phy registers") Signed-off-by: Russell King <[email protected]> Acked-by: Florian Fainelli <[email protected]> Signed-off-by: David S. Miller <[email protected]>
David S. Miller [Tue, 25 Aug 2015 23:28:11 +0000 (16:28 -0700)]
Merge branch 'rds-more-fixes'
Santosh Shilimkar says:
====================
RDS: Few more fixes
As indicated in the earlier series [1], this is a follow-up series which
addresses few issues around the RDS FMR code. With [1] and the subject
series, now I can run many parallel threads with multiple sockets with
N x N traffic. The stress tests has survived overnight runs.
FMR flush is an expensive and time consuming operation. Reduce the
frequency of FMR pool flush by 50% so that more FMR work gets accumulated
for more efficient flushing.
RDS FMR flush operation and also it races with connect/reconect
which happes a lot with RDS. FMR flush being on common rds_wq aggrevates
the problem. Lets push RDS FMR pool flush work to its own worker.
RDS: Fix rds MR reference count in rds_rdma_unuse()
rds_rdma_unuse() drops the mr reference count which it hasn't
taken. Correct way of removing mr is to remove mr from the tree
and then rdma_destroy_mr() it first, then rds_mr_put() to decrement
its reference count. Whichever thread holds last reference will free
the mr via rds_mr_put()
This bug was triggering weird null pointer crashes. One if the trace
for it is captured below.
Before 56ef9c909b40[1] it used to ignore all errors from igmp_join().
That commit enhanced that and made it error out whatever error happened
with igmp_join(), but that's not good because when using multicast
groups vxlan will try to join it multiple times if the socket is reused
and then the 2nd and further attempts will fail with EADDRINUSE.
As we don't track to which groups the socket is already subscribed, it's
okay to just ignore that error.
Fixes: 56ef9c909b40 ("vxlan: Move socket initialization to within rtnl scope") Reported-by: John Nielsen <[email protected]> Signed-off-by: Marcelo Ricardo Leitner <[email protected]> Signed-off-by: David S. Miller <[email protected]>
David S. Miller [Tue, 25 Aug 2015 23:20:38 +0000 (16:20 -0700)]
Merge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge
Antonio Quartulli says:
====================
Included changes:
- code restyling and beautification
- use int kernel types instead of C99
- update kereldoc
- prevent potential hlist double deletion of VLAN objects
- fix gw bandwidth calculation
- convert list to hlist when needed
- add lockdep_asserts calls in function with lock requirements
described in kerneldoc
====================
David S. Miller [Tue, 25 Aug 2015 23:12:45 +0000 (16:12 -0700)]
Merge tag 'linux-can-fixes-for-4.2-20150825' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
this is the updated pull request of one patch by me for the peak_usb
driver. It fixes the driver, so that non FD adapters don't provide CAN
FD bittimings.
====================
Kazuya Mizuguchi [Tue, 25 Aug 2015 08:03:20 +0000 (18:03 +1000)]
net: compile renesas directory if NET_VENDOR_RENESAS is configured
Currently the renesas ethernet driver directory is compiled if SH_ETH is
configured rather than NET_VENDOR_RENESAS. Although incorrect that was
quite harmless as until recently as SH_ETH configured the only driver in
the renesas directory. However, as of c156633f1353 ("Renesas Ethernet AVB
driver proper") the renesas directory includes another driver, configured
by RAVB, and it makes little sense for it to have a hidden dependency on
SH_ETH.
Corinna Vinschen [Mon, 24 Aug 2015 10:52:39 +0000 (12:52 +0200)]
r8169: Add values missing in @get_stats64 from HW counters
The r8169 driver collects statistical information returned by
@get_stats64 by counting them in the driver itself, even though many
(but not all) of the values are already collected by tally counters
(TCs) in the NIC. Some of these TC values are not returned by
@get_stats64. Especially the received multicast packages are missing
from /proc/net/dev.
Rectify this by fetching the TCs and returning them from
rtl8169_get_stats64.
The counters collected in the driver obviously disappear as soon as the
driver is unloaded so after a driver is loaded the counters always start
at 0. The TCs on the other hand are only reset by a power cycle. Without
further considerations the values collected by the driver would not match
up against the TC values.
This patch introduces a new function rtl8169_reset_counters which
resets the TCs. Also, since rtl8169_reset_counters shares most of
its code with rtl8169_update_counters, refactor the shared code into
two new functions rtl8169_map_counters and rtl8169_unmap_counters.
Unfortunately chip versions prior to RTL_GIGA_MAC_VER_19 don't allow
to reset the TCs programatically. Therefore introduce an addition to
the rtl8169_private struct and a function rtl8169_init_counter_offsets
to store the TCs at first rtl_open. Use these values as offsets in
rtl8169_get_stats64. Propagate a failure to reset *and* update the
counters up to rtl_open and emit a warning message, if so.
David S. Miller [Tue, 25 Aug 2015 22:54:25 +0000 (15:54 -0700)]
rds: Fix improper gfp_t usage.
>> net/rds/ib_recv.c:382:28: sparse: incorrect type in initializer (different base types)
net/rds/ib_recv.c:382:28: expected int [signed] can_wait
net/rds/ib_recv.c:382:28: got restricted gfp_t
net/rds/ib_recv.c:828:23: sparse: cast to restricted __le64
huaibin Wang [Tue, 25 Aug 2015 14:20:34 +0000 (16:20 +0200)]
ip6_gre: release cached dst on tunnel removal
When a tunnel is deleted, the cached dst entry should be released.
This problem may prevent the removal of a netns (seen with a x-netns IPv6
gre tunnel):
unregister_netdevice: waiting for lo to become free. Usage count = 3
Jiri Benc [Tue, 25 Aug 2015 16:36:50 +0000 (18:36 +0200)]
vxlan: fix multiple inclusion of vxlan.h
The vxlan_get_sk_family inline function was added after the last #endif,
making multiple inclusion of net/vxlan.h fail. Move it to the proper place.
Reported-by: Mark Rustad <[email protected]> Fixes: 705cc62f6728c ("vxlan: provide access function for vxlan socket address family") Signed-off-by: Jiri Benc <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Masanari Iida [Mon, 24 Aug 2015 13:56:54 +0000 (22:56 +0900)]
net-next: Fix warning while make xmldocs caused by skbuff.c
This patch fix following warnings.
.//net/core/skbuff.c:407: warning: No description found
for parameter 'len'
.//net/core/skbuff.c:407: warning: Excess function parameter
'length' description in '__netdev_alloc_skb'
.//net/core/skbuff.c:476: warning: No description found
for parameter 'len'
.//net/core/skbuff.c:476: warning: Excess function parameter
'length' description in '__napi_alloc_skb'
Guillaume Nault [Mon, 24 Aug 2015 09:35:30 +0000 (11:35 +0200)]
ppp: implement x-netns support
Let packets move from one netns to the other at PPP encapsulation and
decapsulation time.
PPP units and channels remain in the netns in which they were
originally created. Only the net_device may move to a different
namespace. Cross netns handling is thus transparent to lower PPP
layers (PPPoE, L2TP, etc.).
PPP devices are automatically unregistered when their netns gets
removed. So read() and poll() on the unit file descriptor will
respectively receive EOF and POLLHUP. Channels aren't affected.
Rana Shahout [Sun, 23 Aug 2015 13:12:14 +0000 (16:12 +0300)]
net/mlx5e: Avoid accessing NULL pointer at ndo_select_queue
To avoid multiply/division operations on the data path,
we hold a {channel, tc}==>txq mapping table.
We held this mapping table inside the channel object that is
being destroyed upon some configuration operations (e.g MTU change).
So in case ndo_select_queue occurs during such a configuration operation,
it may access a NULL channel pointer, resulting in kernel panic.
To fix this issue we moved the {channel, tc}==>txq mapping table
outside the channel object so that it will be available also
during such configuration operations.
Jeff Moyer [Wed, 29 Jul 2015 14:22:50 +0000 (10:22 -0400)]
mtip32x: fix regression introduced by blk-mq per-hctx flush
Hi,
After commit f70ced091707 (blk-mq: support per-distpatch_queue flush
machinery), the mtip32xx driver may oops upon module load due to walking
off the end of an array in mtip_init_cmd. On initialization of the
flush_rq, init_request is called with request_index >= the maximum queue
depth the driver supports. For mtip32xx, this value is used to index
into an array. What this means is that the driver will walk off the end
of the array, and either oops or cause random memory corruption.
The problem is easily reproduced by doing modprobe/rmmod of the mtip32xx
driver in a loop. I can typically reproduce the problem in about 30
seconds.
Now, in the case of mtip32xx, it actually doesn't support flush/fua, so
I think we can simply return without doing anything. In addition, no
other mq-enabled driver does anything with the request_index passed into
init_request(), so no other driver is affected. However, I'm not really
sure what is expected of drivers. Ming, what did you envision drivers
would do when initializing the flush requests?
David S. Miller [Tue, 25 Aug 2015 20:35:32 +0000 (13:35 -0700)]
Merge branch 'rds-assorted-bug-fixes'
Santosh Shilimkar says:
====================
RDS: Assorted bug fixes
We would like to improve RDS upstream support and in that context, I
started playing with it. But run into number of issues including as
basic is RDS IB RDMA doesn't work. As part of the debug, I ended up
creating the $subject series which has bunch of assorted fixes. At
least with this series I can run RDS IB RDMA and other tests
successfully.
Some of these fixes have been done by Chris Meson, Andy Grover and
Zach Brown while at Oracle. There are still more kinks with FMR and
error handling and I plan to address them in a follow up series.
Series generated against Linus's master(v4.2-rc-7) but also applies
against next-next cleanly. Its tested on Oracle hardware with IB
fabric for both bcopy as well as RDMA mode. I don't have access
to iWARP hardware so any testing help on iWARP hardware appreciated.
====================
Mukesh Kacker [Sat, 22 Aug 2015 22:45:34 +0000 (15:45 -0700)]
RDS: return EMSGSIZE for oversize requests before processing/queueing
rds_send_queue_rm() allows for the "current datagram" being queued
to exceed SO_SNDBUF thresholds by checking bytes queued without
counting in length of current datagram. (Since sk_sndbuf is set
to twice requested SO_SNDBUF value as a kernel heuristic this
is usually fine!)
If this "current datagram" squeezing past the threshold is itself
many times the size of the sk_sndbuf threshold itself then even
twice the SO_SNDBUF does not save us and it gets queued but
cannot be transmitted. Threads block and deadlock and device
becomes unusable. The check for this datagram not exceeding
SNDBUF thresholds (EMSGSIZE) is not done on this datagram as
that check is only done if queueing attempt fails.
(Datagrams that follow this datagram fail queueing attempts, go
through the check and eventually trip EMSGSIZE error but zero
length datagrams silently fail!)
This fix moves the check for datagrams exceeding SNDBUF limits
before any processing or queueing is attempted and returns EMSGSIZE
early in the rds_sndmsg() code. This change also ensures that all
datagrams get checked for exceeding SNDBUF/sk_sndbuf size limits
and the large datagrams that exceed those limits do not get to
rds_send_queue_rm() code for processing.
RDS: make sure rds_send_drop_to properly takes the m_rs_lock
rds_send_drop_to() is used during socket tear down to find all the
messages on the socket and flush them . It can race with the
acking code unless it takes the m_rs_lock on each and every message.
This plugs a hole where we didn't take m_rs_lock on any message that
didn't have the RDS_MSG_ON_CONN set. Taking m_rs_lock avoids
double frees and other memory corruptions as the ack code trusts
the message m_rs pointer on a socket that had actually been freed.
We must take m_rs_lock to access m_rs. Because of lock nesting and
rs access, we also need to acquire rs_lock.
RDS: Don't destroy the rdma id until after we're done using it
During connection resets, we are destroying the rdma id too soon. We can't
destroy it when it is still in use. So lets move rdma_destroy_id() after
we clear the rings.
RDS: Make sure we do a signaled send for large-send
WR(Work Requests )always generate a WC(Work Completion) with
signaled send. Default RDS ib code is setup for un-signaled
completion. Since RDS connction is persistent, we can end up
sending the data even after large-send when the remote end is
not active(for any reason).
By doing a signaled send at least once per large-send,
we can at least detect the problem in work completion
handler there by avoiding sending more data to
inactive remote.
rds_send_xmit() marks the rds message map flag after
xmit_[rdma/atomic]() which is clearly wrong. We need
to maintain the ownership between transport and rds.
If we get an ENOMEM during rds_ib_recv_refill, we might never come
back and refill again later. Patch makes sure to kick krdsd into
helping out.
To achieve this we add RDS_RECV_REFILL flag and update in the refill
path based on that so that at least some therad will keep posting
receive buffers.
Since krdsd and softirq both might race for refill, we decide to
schedule on work queue based on ring_low instead of ring_empty.
RDS: always free recv frag as we free its ring entry
We were still seeing rare occurrences of the WARN_ON(recv->r_frag) which
indicates that the recv refill path was finding allocated frags in ring
entries that were marked free. These were usually followed by OOM crashes.
They only seem to be occurring in the presence of completion errors and
connection resets.
This patch ensures that we free the frag as we mark the ring entry free.
This should stop the refill path from finding allocated frags in ring
entries that were marked free.
In rds_cmsg_rdma_args() 'ret' is used by rds_pin_pages() which returns
number of pinned pages on success. And the same value is returned to the
caller of rds_cmsg_rdma_args() on success which is not intended.
Commit f4a3fc03c1d7 ("RDS: Clean up error handling in rds_cmsg_rdma_args")
removed the 'ret = 0' line which broke RDS RDMA mode.
Fix it by restoring the return value on rds_pin_pages() success
keeping the clean-up in place.
Tejun Heo [Tue, 25 Aug 2015 18:11:52 +0000 (14:11 -0400)]
writeback: sync_inodes_sb() must write out I_DIRTY_TIME inodes and always call wait_sb_inodes()
e79729123f63 ("writeback: don't issue wb_writeback_work if clean")
updated writeback path to avoid kicking writeback work items if there
are no inodes to be written out; unfortunately, the avoidance logic
was too aggressive and broke sync_inodes_sb().
* sync_inodes_sb() must write out I_DIRTY_TIME inodes but I_DIRTY_TIME
inodes dont't contribute to bdi/wb_has_dirty_io() tests and were
being skipped over.
* inodes are taken off wb->b_dirty/io/more_io lists after writeback
starts on them. sync_inodes_sb() skipping wait_sb_inodes() when
bdi_has_dirty_io() breaks it by making it return while writebacks
are in-flight.
This patch fixes the breakages by
* Removing bdi_has_dirty_io() shortcut from bdi_split_work_to_wbs().
The callers are already testing the condition.
* Removing bdi_has_dirty_io() shortcut from sync_inodes_sb() so that
it always calls into bdi_split_work_to_wbs() and wait_sb_inodes().
* Making bdi_split_work_to_wbs() consider the b_dirty_time list for
WB_SYNC_ALL writebacks.
Kudos to Eryu, Dave and Jan for tracking down the issue.
Eric Dumazet [Sat, 22 Aug 2015 00:38:02 +0000 (17:38 -0700)]
tcp: refine pacing rate determination
When TCP pacing was added back in linux-3.12, we chose
to apply a fixed ratio of 200 % against current rate,
to allow probing for optimal throughput even during
slow start phase, where cwnd can be doubled every other gRTT.
At Google, we found it was better applying a different ratio
while in Congestion Avoidance phase.
This ratio was set to 120 %.
We've used the normal tcp_in_slow_start() helper for a while,
then tuned the condition to select the conservative ratio
as soon as cwnd >= ssthresh/2 :
- After cwnd reduction, it is safer to ramp up more slowly,
as we approach optimal cwnd.
- Initial ramp up (ssthresh == INFINITY) still allows doubling
cwnd every other RTT.
David Daney [Fri, 21 Aug 2015 23:16:03 +0000 (16:16 -0700)]
phylib: Make PHYs children of their MDIO bus, not the bus' parent.
commit 18ee49ddb0d2 ("phylib: rename mii_bus::dev to mii_bus::parent")
changed the parent of PHY devices from the bus to the bus parent.
Then, commit 4dea547fef1b ("phylib: rework to prepare for OF
registration of PHYs") moved the code into phy_device.c
At this point, it is somewhat unclear why the change was seen as
necessary. But, when we look at the device model tree in
/sys/devices, it is clearly incorrect. The PHYs should be children of
their MDIO bus.
Change the PHY's parent device to be the MDIO bus device.
David Ahern [Thu, 20 Aug 2015 22:06:30 +0000 (15:06 -0700)]
xfrm: Use VRF master index if output device is enslaved
Directs route lookups to VRF table. Compiles out if NET_VRF is not
enabled. With this patch able to successfully bring up ipsec tunnels
in VRFs, even with duplicate network configuration.
Eric Dumazet [Fri, 21 Aug 2015 19:30:00 +0000 (12:30 -0700)]
tcp: fix slow start after idle vs TSO/GSO
slow start after idle might reduce cwnd, but we perform this
after first packet was cooked and sent.
With TSO/GSO, it means that we might send a full TSO packet
even if cwnd should have been reduced to IW10.
Moving the SSAI check in skb_entail() makes sense, because
we slightly reduce number of times this check is done,
especially for large send() and TCP Small queue callbacks from
softirq context.
As Neal pointed out, we also need to perform the check
if/when receive window opens.
Tested:
Following packetdrill test demonstrates the problem
// Test of slow start after idle
Linus Torvalds [Tue, 25 Aug 2015 16:01:05 +0000 (09:01 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fix from Thomas Gleixner:
"A single fix for a APIC regression introduced in 4.0 which went
undetected until now.
I screwed up the x2apic cleanup in a subtle way. The screwup is only
visible on systems which have x2apic preenabled in the BIOS and need
to disable it during boot"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic: Fix fallout from x2apic cleanup
Commit 5d5cd85ff441 ("rsi: Fix failure to load firmware after memory
leak fix and fix the leak") also added a check on the allocation of
DMA-accessible memory that may directly return. In that case the
already allocated firmware data is leaked. Make sure the data is
always freed correctly. Detected by Coverity CID 1316519.
Fixes: 5d5cd85ff441 ("rsi: Fix failure to load firmware after memory leak fix and fix the leak") Signed-off-by: Christian Engelmayer <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
Hante Meuleman [Thu, 20 Aug 2015 20:06:08 +0000 (22:06 +0200)]
brcmfmac: Add support for host platform NVRAM loading.
Host platforms such as routers supported by OpenWRT can
support NVRAM reading directly from internal NVRAM store.
With this patch the nvram load routines will fall back to
this method when there is no nvram file and support is
available in the kernel.
Arend van Spriel [Thu, 20 Aug 2015 20:06:07 +0000 (22:06 +0200)]
brcmfmac: bump highest event number for 4339 firmware
The event mask length is determined by the highest event number
that is specified in the driver. When this length is shorter than
firmware expects setting event mask will fail and device becomes
pretty useless. This issue was reported with bcm4339 firmware that
was recently released.
Franky Lin [Thu, 20 Aug 2015 20:06:06 +0000 (22:06 +0200)]
brcmfmac: block the correct flowring when backup queue overflow
brcmf_flowring_block blocks the last active flowring under the same
interface instead of the one provided by caller. This could lead to a
dead lock of netif stop if there are more than one flowring under the
interface and the traffic is high enough so brcmf_flowring_enqueue can
not unblock the ring right away.
Rafał Miłecki [Wed, 19 Aug 2015 22:16:42 +0000 (00:16 +0200)]
brcmfmac: check all combinations when setting wiphy's addresses
Broadcom is working on better reflection of interface combinations. With
upcoming patches we may have 1st combination supporting less interfaces
than others.
To don't run out of addresses check all combinations to find the one
with the greatest max_interfaces value.
Oleksij Rempel [Fri, 14 Aug 2015 05:16:39 +0000 (07:16 +0200)]
ath9k_htc: do ani shortcalibratio if we got -ETIMEDOUT
current code will handle -ETIMEDOUT as success which is probalbly wrong.
According to this comment I assume it is safe to handle -ETIMEDOUT as false:
drivers/net/wireless/ath/ath9k/calib.c
290 /*
291 * We timed out waiting for the noisefloor to load, probably due to an
292 * in-progress rx. Simply return here and allow the load plenty of time
293 * to complete before the next calibration interval. We need to avoid
294 * trying to load -50 (which happens below) while the previous load is
295 * still in progress as this can cause rx deafness. Instead by returning
296 * here, the baseband nf cal will just be capped by our present
297 * noisefloor until the next calibration timer.
298 */
Since no other error wariants are present, this patch is checking only
for (ret <= 0).
Kalle Valo [Tue, 25 Aug 2015 11:54:38 +0000 (14:54 +0300)]
Merge tag 'iwlwifi-next-for-kalle-2015-08-23' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* new Tx power firmware API
* bump max firmware API to 17
* fix bug in debug prints
* static checker fix
* fix unused defines
* fix command list on newest firmware
can: pcan_usb: don't provide CAN FD bittimings by non-FD adapters
The CAN FD data bittiming constants are provided via netlink only when there
are valid CAN FD constants available in priv->data_bittiming_const.
Due to the indirection of pointer assignments in the peak_usb driver the
priv->data_bittiming_const never becomes NULL - not even for non-FD adapters.
The data_bittiming_const points to zero'ed data which leads to this result
when running 'ip -details link show can0':
35: can0: <NOARP,ECHO> mtu 16 qdisc noop state DOWN mode DEFAULT group default qlen 10
link/can promiscuity 0
can state STOPPED restart-ms 0
pcan_usb: tseg1 1..16 tseg2 1..8 sjw 1..4 brp 1..64 brp-inc 1
: dtseg1 0..0 dtseg2 0..0 dsjw 1..0 dbrp 0..0 dbrp-inc 0 <== BROKEN!
clock 8000000
This patch changes the struct peak_usb_adapter::bittiming_const and struct
peak_usb_adapter::data_bittiming_const to pointers to fix the assignemnt
problems.
Sven Eckelmann [Sun, 21 Jun 2015 12:45:15 +0000 (14:45 +0200)]
batman-adv: Add lockdep_asserts for documented external locks
Some functions already have documentation about locks they require inside
their kerneldoc header. These can be directly tested during runtime using
the lockdep asserts.
Sven Eckelmann [Sun, 21 Jun 2015 12:45:14 +0000 (14:45 +0200)]
batman-adv: Annotate deleting functions with external lock via lockdep
Functions which use (h)list_del* are requiring correct locking when they
operate on global lists. Most of the time the search in the list and the
delete are done in the same function. All other cases should have it
visible that they require a special lock to avoid race conditions.
Lockdep asserts can be used to check these problem during runtime when the
lockdep functionality is enabled.
Sven Eckelmann [Sun, 21 Jun 2015 17:40:09 +0000 (19:40 +0200)]
batman-adv: Fix gw_bandwidth calculation on 32 bit systems
The TVLV for the gw_bandwidth stores everything as u32. But the
gw_bandwidth reads the signed long which limits the maximum value to
(2 ** 31 - 1) on systems with 4 byte long. Also the input value is always
converted from either Mibit/s or Kibit/s to 100Kibit/s. This reduces the
values even further when the user sets it via the default unit Kibit/s. It
may even cause an integer overflow and end up with a value the user never
intended.
Instead read the values as u64, check for possible overflows, do the unit
adjustments and then reduce the size to u32.
Sven Eckelmann [Sun, 21 Jun 2015 12:42:49 +0000 (14:42 +0200)]
batman-adv: Return EINVAL on invalid gw_bandwidth change
Invalid speed settings by the user are currently acknowledged as correct
but not stored. Instead the return of the store operation of the file
"gw_bandwidth" should indicate that the given value is not acceptable.
The hlist_del_rcu() call in batadv_tt_global_size_mod() does not check
if the element still is part of the list prior to deletion. The atomic
list counter should prevent the worst but converting to
hlist_del_init_rcu() ensures the element can't be deleted more than
once.
Sven Eckelmann [Sun, 31 May 2015 08:10:20 +0000 (10:10 +0200)]
batman-adv: Fix kerneldoc over 80 column lines
Kerneldoc required single line documentation in the past (before 2009).
Therefore, the 80 columns limit per line check of checkpatch was disabled
for kerneldoc. But kerneldoc is not excluded anymore from it and checkpatch
now enabled the check again.
Sven Eckelmann [Tue, 26 May 2015 16:34:26 +0000 (18:34 +0200)]
batman-adv: Replace C99 int types with kernel type
(s|u)(8|16|32|64) are the preferred types in the kernel. The use of the
standard C99 types u?int(8|16|32|64)_t are objected by some people and even
checkpatch now warns about using them.
J. Bruce Fields [Mon, 24 Aug 2015 20:44:40 +0000 (16:44 -0400)]
nfsd: Add Jeff Layton as co-maintainer
Jeff has been doing a lot of development (including much of the
state-locking rewrite just as one example) plus lots of review and other
miscellaneous nfsd work, so let's acknowledge the status quo.
I'll continue to be the one to send regular pull requests but Jeff will
should be available to cover there occasionally too.
In pfkey_sendmsg the net mutex is taken and then pfkey_broadcast takes
the RCU lock.
Since pfkey_broadcast takes the RCU lock the allocation argument is
pointless since GFP_ATOMIC must be used between the rcu_read_{,un}lock.
The one call outside of rcu can be done with GFP_KERNEL.
This patchsets adds FUJITSU Extended Socket network device driver.
Extended Socket network device is a shared memory based high-speed
network interface between Extended Partitions of PRIMEQUEST 2000 E2
series.
You can get some information about Extended Partition and Extended
Socket by referring the following manual.
projects / linux.git / log