Merge tag 'nand/for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
Core changes:
* Drop useless 'depends on' in Kconfig
* Add an extra level in the Kconfig hierarchy
* Trivial spellings
* Dynamic allocation of the interface configurations
* Dropping the default ONFI timing mode
* Various cleanup (types, structures, naming, comments)
* Hide the chip->data_interface indirection
* Add the generic rb-gpios property
* Add the ->choose_interface_config() hook
* Introduce nand_choose_best_sdr_timings()
* Use default values for tPROG_max and tBERS_max
* Avoid redefining tR_max and tCCS_min
* Add a helper to find the closest ONFI mode
* bcm63xx MTD parsers: simplify CFE detection
Raw NAND controller drivers changes:
* fsl-upm: Deprecation of specific DT properties
* fsl_upm: Driver rework and cleanup in favor of ->exec_op()
* Ingenic: Cleanup ARRAY_SIZE() vs sizeof() use
* brcmnand: ECC error handling on EDU transfers
* brcmnand: Don't default to EDU transfers
* qcom: Set BAM mode only if not set already
* qcom: Avoid write to unavailable register
* gpio: Driver rework in favor of ->exec_op()
* tango: ->exec_op() conversion
* mtk: ->exec_op() conversion
Raw NAND chip drivers changes:
* toshiba: Implement ->choose_interface_config() for TH58NVG2S3HBAI4
* toshiba: Implement ->choose_interface_config() for TC58NVG0S3E
* toshiba: Implement ->choose_interface_config() for TC58TEG5DCLTA00
* hynix: Implement ->choose_interface_config() for H27UCG8T2ATR-BC
mtd: rawnand: omap_elm: Replace HTTP links with HTTPS ones
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Merge tag 'spi-nor/for-5.9' of https://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
SPI NOR core changes:
- Disable Quad Mode in spi_nor_restore().
- Don't abort BFPT parsing when QER reserved value is used.
- Add support/update capabilities for few flashes.
- Drop s70fl01gs flash: it does not support RDSR(05h) which
is critical for erase/write.
- Merge the SPIMEM DTR bits in spi-nor/next to avoid conflicts
during the release cycle.
SPI NOR controller drivers changes:
- Move the cadence-quadspi driver to spi-mem. The series was
taken through the SPI tree. Merge it also in spi-nor/next
to avoid conflicts during the release cycle.
- intel-spi:
- Add new PCI IDs.
- Ignore the Write Disable command, the controller doesn't
support it.
- Fix performance regression.
mtd: revert "spi-nor: intel: provide a range for poll_timout"
This change reverts aba3a882a178: "mtd: spi-nor: intel: provide a range
for poll_timout". That change introduces a performance regression when
reading sequentially from flash. Logging calls to intel_spi_read without
this change we get:
David Clear [Mon, 20 Jul 2020 16:36:56 +0000 (09:36 -0700)]
mtd: spi-nor: micron: Add SPI_NOR_DUAL_READ flag on mt25qu02g
The Micron mt25qu02g supports both x2 and x4 transactions. Add the
SPI_NOR_DUAL_READ flag to its spi_nor_ids[] table entry.
Tested on Pensando SoC hardware with a cadence quadspi controller
via drivers/spi/spi-cadence-quadspi.c, in x2 mode at 50MHz.
- random data write, erase, read - verified erase operations
- random data write, read/compare - verified write/read operations
David Clear [Mon, 20 Jul 2020 16:36:55 +0000 (09:36 -0700)]
mtd: spi-nor: macronix: Add support for mx66u2g45g
The Macronix mx66u2g45g is a 1.8V, 2Gbit (256MB) device that
supports x1, x2, or x4 operation.
Tested on Pensando SoC hardware with a cadence quadspi controller
via drivers/spi/spi-cadence-quadspi.c, in x2 mode at 50MHz.
- random data write, erase, read - verified erase operations
- random data write, read/compare - verified write/read operations
After spi_nor_write_disable() return code checks were introduced in the
spi-nor front end intel-spi backend stopped to work because WRDI was never
supported and always failed.
Just pretend it was sucessful and ignore the command itself. HW sequencer
shall do the right thing automatically, while with SW sequencer we cannot
do it anyway, because the only tool we had was preopcode and it makes no
sense for WRDI.
Pratyush Yadav [Tue, 23 Jun 2020 18:30:17 +0000 (00:00 +0530)]
spi: spi-mtk-nor: reject DTR ops
Double Transfer Rate (DTR) ops are added in spi-mem. But this controller
doesn't support DTR transactions. Since we don't use the default
supports_op(), which rejects all DTR ops, do that explicitly in our
supports_op().
Pratyush Yadav [Tue, 23 Jun 2020 18:30:16 +0000 (00:00 +0530)]
spi: atmel-quadspi: reject DTR ops
Double Transfer Rate (DTR) ops are added in spi-mem. But this controller
doesn't support DTR transactions. Since we don't use the default
supports_op(), which rejects all DTR ops, do that explicitly in our
supports_op().
Pratyush Yadav [Tue, 23 Jun 2020 18:30:15 +0000 (00:00 +0530)]
spi: spi-mem: allow specifying a command's extension
In xSPI mode, flashes expect 2-byte opcodes. The second byte is called
the "command extension". There can be 3 types of extensions in xSPI:
repeat, invert, and hex. When the extension type is "repeat", the same
opcode is sent twice. When it is "invert", the second byte is the
inverse of the opcode. When it is "hex" an additional opcode byte based
is sent with the command whose value can be anything.
So, make opcode a 16-bit value and add a 'nbytes', similar to how
multiple address widths are handled.
Some places use sizeof(op->cmd.opcode). Replace them with op->cmd.nbytes
The spi-mxic and spi-zynq-qspi drivers directly use op->cmd.opcode as a
buffer. Now that opcode is a 2-byte field, this can result in different
behaviour depending on if the machine is little endian or big endian.
Extract the opcode in a local 1-byte variable and use that as the buffer
instead. Both these drivers would reject multi-byte opcodes in their
supports_op() hook anyway, so we only need to worry about single-byte
opcodes for now.
The above two changes are put in this commit to keep the series
bisectable.
Yicong Yang [Mon, 6 Jul 2020 09:22:36 +0000 (17:22 +0800)]
mtd: spi-nor: Disable the flash quad mode in spi_nor_restore()
If the flash's quad mode is enabled, it'll remain in the quad mode when
it's removed. If we drive the flash next time in Standard/Dual SPI mode,
the QE bit is not cleared and the function of flash's WP# and RESET#/HOLD#
have been switched to IO2 and IO3 and are not restored.
Disable the Quad mode in spi_nor_restore(), then the flash's QE bit will
be cleared when removed. This will make sure the flash always enter the
Standard/Dual SPI mode when loaded.
Yicong Yang [Mon, 6 Jul 2020 09:22:35 +0000 (17:22 +0800)]
mtd: spi-nor: Add capability to disable flash quad mode
Previous we didn't provide a way to disable the flash's quad mode.
Which means we cannot do some cleanup works when to remove or
poweroff the flash, like what set 4-byte address mode does in
spi_nor_restore().
Add the capability to disable the flash quad mode, by introducing
an enable flag in the flash parameters quad_enable() hooks and
related functions.
Takahiro Kuwano [Fri, 26 Jun 2020 05:16:50 +0000 (14:16 +0900)]
mtd: spi-nor: spansion: Remove s70fl01gs from flash_info
The s70fl01gs is a dual die stack of two s25fl512s die with dedicated chip
select pins to each. Tested with the device and confirmed that is working
as two s25fl512s devices. The current device ID in the flash_info table
matches with s70fs01gs which does not work with current MTD (s70fs01gs
does not support RDSR(05h) which is critical for erase/write).
Pratyush Yadav [Tue, 23 Jun 2020 18:30:24 +0000 (00:00 +0530)]
mtd: spi-nor: sfdp: do not make invalid quad enable fatal
The Micron MT35XU512ABA flash does not support the quad enable bit. But
instead of programming the Quad Enable Require field to 000b ("Device
does not have a QE bit"), it is programmed to 111b ("Reserved").
While this is technically incorrect, it is not reason enough to abort
BFPT parsing. Instead, continue BFPT parsing and let flashes set it in
their fixup hooks.
mtd: rawnand: stm32_fmc2: get resources from parent node
FMC2 EBI support has been added. Common resources (registers base
address and clock) can now be shared between the 2 drivers using
"st,stm32mp1-fmc2-nfc" compatible string. It means that the
common resources should now be found in the parent device when EBI
node is available.
These bindings can be used on SOCs where the FMC2 NAND controller is
in standalone. In case that the FMC2 embeds 2 controllers (an external
bus controller and a raw NAND controller), the register base address,
the clock and the reset will be defined in the parent node.
mtd: rawnand: stm32_fmc2: do not display errors if the driver is deferred
A MDMA issue has been solved on Kernel 5.7. The effect of this fix is
that the MDMA driver is now deferred and the FMC2 NFC driver is also
deferred. All is working fine but there is a FMC2 log in the console:
stm32_fmc2_nfc 58002000.nand-controller: failed to request tx DMA
channel: -517
This patch removes the display of this log in the console in case of
this error is -EPROBE_DEFER.
Dan Carpenter [Wed, 24 Jun 2020 13:26:40 +0000 (16:26 +0300)]
mtd: rawnand: ingenic: cleanup ARRAY_SIZE() vs sizeof() use
The ARRAY_SIZE() is the number of elements but we want to use sizeof()
here for the number of bytes. Fortunately, they are the same thing
because it's an array of u8 so this has no effect on runtime.
x86/ldt: use "pr_info_once()" instead of open-coding it badly
Using a mutex for "print this warning only once" is so overdesigned as
to be actively offensive to my sensitive stomach.
Just use "pr_info_once()" that already does this, although in a
(harmlessly) racy manner that can in theory cause the message to be
printed twice if more than one CPU races on that "is this the first
time" test.
[ If somebody really cares about that harmless data race (which sounds
very unlikely indeed), that person can trivially fix printk_once() by
using a simple atomic access, preferably with an optimistic non-atomic
test first before even bothering to treat the pointless "make sure it
is _really_ just once" case.
A mutex is most definitely never the right primitive to use for
something like this. ]
Yes, this is a small and meaningless detail in a code path that hardly
matters. But let's keep some code quality standards here, and not
accept outrageously bad code.
Merge tag 'x86-urgent-2020-07-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A series of fixes for x86:
- Reset MXCSR in kernel_fpu_begin() to prevent using a stale user
space value.
- Prevent writing MSR_TEST_CTRL on CPUs which are not explicitly
whitelisted for split lock detection. Some CPUs which do not
support it crash even when the MSR is written to 0 which is the
default value.
- Fix the XEN PV fallout of the entry code rework
- Fix the 32bit fallout of the entry code rework
- Add more selftests to ensure that these entry problems don't come
back.
- Disable 16 bit segments on XEN PV. It's not supported because XEN
PV does not implement ESPFIX64"
* tag 'x86-urgent-2020-07-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/ldt: Disable 16-bit segments on Xen PV
x86/entry/32: Fix #MC and #DB wiring on x86_32
x86/entry/xen: Route #DB correctly on Xen PV
x86/entry, selftests: Further improve user entry sanity checks
x86/entry/compat: Clear RAX high bits on Xen PV SYSENTER
selftests/x86: Consolidate and fix get/set_eflags() helpers
selftests/x86/syscall_nt: Clear weird flags after each test
selftests/x86/syscall_nt: Add more flag combinations
x86/entry/64/compat: Fix Xen PV SYSENTER frame setup
x86/entry: Move SYSENTER's regs->sp and regs->flags fixups into C
x86/entry: Assert that syscalls are on the right stack
x86/split_lock: Don't write MSR_TEST_CTRL on CPUs that aren't whitelisted
x86/fpu: Reset MXCSR to default in kernel_fpu_begin()
Merge tag 'irq-urgent-2020-07-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A set of interrupt chip driver fixes:
- Ensure the atomicity of affinity updates in the GIC driver
- Don't try to sleep in atomic context when waiting for the GICv4.1
to respond. Use polling instead.
- Typo fixes in Kconfig and warnings"
* tag 'irq-urgent-2020-07-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic: Atomically update affinity
irqchip/riscv-intc: Fix a typo in a pr_warn()
irqchip/gic-v4.1: Use readx_poll_timeout_atomic() to fix sleep in atomic
irqchip/loongson-pci-msi: Fix a typo in Kconfig
Merge tag 'kbuild-fixes-v5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes frin Masahiro Yamada:
- fix various bugs in xconfig
- fix some issues in cross-compilation using Clang
- fix documentation
* tag 'kbuild-fixes-v5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
.gitignore: Do not track `defconfig` from `make savedefconfig`
kbuild: make Clang build userprogs for target architecture
kbuild: fix CONFIG_CC_CAN_LINK(_STATIC) for cross-compilation with Clang
kconfig: qconf: parse newer types at debug info
kconfig: qconf: navigate menus on hyperlinks
kconfig: qconf: don't show goback button on splitMode
kconfig: qconf: simplify the goBack() logic
kconfig: qconf: re-implement setSelected()
kconfig: qconf: make debug links work again
kconfig: qconf: make search fully work again on split mode
kconfig: qconf: cleanup includes
docs: kbuild: fix ReST formatting
gcc-plugins: fix gcc-plugins directory path in documentation
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Four small fixes in three drivers.
The mptfusion one has actually caused user visible issues in certain
kernel configurations"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: mptfusion: Don't use GFP_ATOMIC for larger DMA allocations
scsi: libfc: Skip additional kref updating work event
scsi: libfc: Handling of extra kref
scsi: qla2xxx: Fix a condition in qla2x00_find_all_fabric_devs()
Merge tag 'block-5.8-2020-07-05' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- NVMe fixes from Christoph:
- Fix crash in multi-path disk add (Christoph)
- Fix ignore of identify error (Sagi)
- Fix a compiler complaint that a function should be static (Wei)
* tag 'block-5.8-2020-07-05' of git://git.kernel.dk/linux-block:
block: make function __bio_integrity_free() static
nvme: fix a crash in nvme_mpath_add_disk
nvme: fix identify error status silent ignore
Merge tag 'io_uring-5.8-2020-07-05' of git://git.kernel.dk/linux-block
Pull io_uring fix from Jens Axboe:
"Andres reported a regression with the fix that was merged earlier this
week, where his setup of using signals to interrupt io_uring CQ waits
no longer worked correctly.
Fix this, and also limit our use of TWA_SIGNAL to the case where we
need it, and continue using TWA_RESUME for task_work as before.
Since the original is marked for 5.7 stable, let's flush this one out
early"
* tag 'io_uring-5.8-2020-07-05' of git://git.kernel.dk/linux-block:
io_uring: fix regression with always ignoring signals in io_cqring_wait()
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"The usual driver fixes and documentation updates"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: mlxcpld: check correct size of maximum RECV_LEN packet
i2c: add Kconfig help text for slave mode
i2c: slave-eeprom: update documentation
i2c: eg20t: Load module automatically if ID matches
i2c: designware: platdrv: Set class based on DMI
i2c: algo-pca: Add 0x78 as SCL stuck low status for PCA9665
Merge tag 'mips_fixes_5.8_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Thomas Bogendoerfer:
- fix for missing hazard barrier
- DT fix for ingenic
- DT fix of GPHY names for lantiq
- fix usage of smp_processor_id() while preemption is enabled
* tag 'mips_fixes_5.8_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: Do not use smp_processor_id() in preemptible code
MIPS: Add missing EHB in mtc0 -> mfc0 sequence for DSPen
MIPS: ingenic: gcw0: Fix HP detection GPIO.
MIPS: lantiq: xway: sysctrl: fix the GPHY clock alias names
MIPS: Add missing EHB in mtc0 -> mfc0 sequence for DSPen
This resolves the hazard between the mtc0 in the change_c0_status() and
the mfc0 in configure_exception_vector(). Without resolving this hazard
configure_exception_vector() could read an old value and would restore
this old value again. This would revert the changes change_c0_status()
did. I checked this by printing out the read_c0_status() at the end of
per_cpu_trap_init() and the ST0_MX is not set without this patch.
The hazard is documented in the MIPS Architecture Reference Manual Vol.
III: MIPS32/microMIPS32 Privileged Resource Architecture (MD00088), rev
6.03 table 8.1 which includes:
I saw this hazard on an Atheros AR9344 rev 2 SoC with a MIPS 74Kc CPU.
There the change_c0_status() function would activate the DSPen by
setting ST0_MX in the c0_status register. This was reverted and then the
system got a DSP exception when the DSP registers were saved in
save_dsp() in the first process switch. The crash looks like this:
We saw this problem in OpenWrt only on the MIPS 74Kc based Atheros SoCs,
not on the 24Kc based SoCs. We only saw it with kernel 5.4 not with
kernel 4.19, in addition we had to use GCC 8.4 or 9.X, with GCC 8.3 it
did not happen.
In the kernel I bisected this problem to commit 9012d011660e ("compiler:
allow all arches to enable CONFIG_OPTIMIZE_INLINING"), but when this was
reverted it also happened after commit 172dcd935c34b ("MIPS: Always
allocate exception vector for MIPSr2+").
Commit 0b24cae4d535 ("MIPS: Add missing EHB in mtc0 -> mfc0 sequence.")
does similar changes to a different file. I am not sure if there are
more places affected by this problem.
Paul Menzel [Thu, 2 Jul 2020 11:12:00 +0000 (13:12 +0200)]
.gitignore: Do not track `defconfig` from `make savedefconfig`
Running `make savedefconfig` creates by default `defconfig`, which is,
currently, on git’s radar, for example, `git status` lists this file as
untracked.
So, add the file to `.gitignore`, so it’s ignored by git.
Merge tag 'powerpc-5.8-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"One fix for a regression in our pkey handling, which exhibits as
PROT_EXEC mappings taking continuous page faults.
Thanks to: Jan Stancek, Aneesh Kumar K.V"
* tag 'powerpc-5.8-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/mm/pkeys: Make pkey access check work on execute_only_key
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Nothing earth-shattering, really - some CPU errata workarounds (one
day they'll get it right, ha!) and a fix for a boot failure with very
large kernel images where the alternative patching gets confused when
patching relative branches using veneers.
- Fix alternative patching for very large kernel images and modules
- Hook up existing CPU errata workarounds for Qualcomm Kryo CPUs"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Add KRYO4XX silver CPU cores to erratum list 1530923 and 1024718
arm64: Add KRYO4XX gold CPU cores to erratum list 1463225 and 1418040
arm64: Add MIDR value for KRYO4XX gold CPU cores
arm64/alternatives: use subsections for replacement sequences
io_uring: fix regression with always ignoring signals in io_cqring_wait()
When switching to TWA_SIGNAL for task_work notifications, we also made
any signal based condition in io_cqring_wait() return -ERESTARTSYS.
This breaks applications that rely on using signals to abort someone
waiting for events.
Check if we have a signal pending because of queued task_work, and
repeat the signal check once we've run the task_work. This provides a
reliable way of telling the two apart.
Additionally, only use TWA_SIGNAL if we are using an eventfd. If not,
we don't have the dependency situation described in the original commit,
and we can get by with just using TWA_RESUME like we previously did.
Andy Lutomirski [Fri, 3 Jul 2020 17:02:57 +0000 (10:02 -0700)]
x86/ldt: Disable 16-bit segments on Xen PV
Xen PV doesn't implement ESPFIX64, so they don't work right. Disable
them. Also print a warning the first time anyone tries to use a
16-bit segment on a Xen PV guest that would otherwise allow it
to help people diagnose this change in behavior.
This gets us closer to having all x86 selftests pass on Xen PV.
Andy Lutomirski [Fri, 3 Jul 2020 17:02:55 +0000 (10:02 -0700)]
x86/entry/xen: Route #DB correctly on Xen PV
On Xen PV, #DB doesn't use IST. It still needs to be correctly routed
depending on whether it came from user or kernel mode.
Get rid of DECLARE/DEFINE_IDTENTRY_XEN -- it was too hard to follow the
logic. Instead, route #DB and NMI through DECLARE/DEFINE_IDTENTRY_RAW on
Xen, and do the right thing for #DB. Also add more warnings to the
exc_debug* handlers to make this type of failure more obvious.
This fixes various forms of corruption that happen when usermode
triggers #DB on Xen PV.
Merge tag 'for-linus-5.8b-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"One small cleanup patch for ARM and two patches for the xenbus driver
fixing latent problems (large stack allocations and bad return code
settings)"
* tag 'for-linus-5.8b-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/xenbus: let xenbus_map_ring_valloc() return errno values only
xen/xenbus: avoid large structs and arrays on the stack
arm/xen: remove the unused macro GRANT_TABLE_PHYSADDR
Wolfram Sang [Sun, 28 Jun 2020 11:52:44 +0000 (13:52 +0200)]
i2c: mlxcpld: check correct size of maximum RECV_LEN packet
I2C_SMBUS_BLOCK_MAX defines already the maximum number as defined in the
SMBus 2.0 specs. I don't see a reason to add 1 here. Also, fix the errno
to what is suggested for this error.
Chris Packham [Wed, 1 Jul 2020 22:39:11 +0000 (10:39 +1200)]
i2c: algo-pca: Add 0x78 as SCL stuck low status for PCA9665
The PCA9665 datasheet says that I2CSTA = 78h indicates that SCL is stuck
low, this differs to the PCA9564 which uses 90h for this indication.
Treat either 0x78 or 0x90 as an indication that the SCL line is stuck.
Based on looking through the PCA9564 and PCA9665 datasheets this should
be safe for both chips. The PCA9564 should not return 0x78 for any valid
state and the PCA9665 should not return 0x90.
Merge tag '5.8-rc3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Eight cifs/smb3 fixes, most when specifying the multiuser mount flag.
Five of the fixes are for stable"
* tag '5.8-rc3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: prevent truncation from long to int in wait_for_free_credits
cifs: Fix the target file was deleted when rename failed.
SMB3: Honor 'posix' flag for multiuser mounts
SMB3: Honor 'handletimeout' flag for multiuser mounts
SMB3: Honor lease disabling for multiuser mounts
SMB3: Honor persistent/resilient handle flags for multiuser mounts
SMB3: Honor 'seal' flag for multiuser mounts
cifs: Display local UID details for SMB sessions in DebugData
Merge tag 'hwmon-for-v5.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
- Fix typo in Kconfig SENSORS_IR35221 option
- Fix potential memory leak in acpi_power_meter_add()
- Make sure the OVERT mask is set correctly in max6697 driver
- In PMBus core, fix page vs. register when accessing fans
- Mark is_visible functions static in bt1-pvt driver
- Define Temp- and Volt-to-N poly as maybe-unused in bt1-pvt driver
* tag 'hwmon-for-v5.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (pmbus) fix a typo in Kconfig SENSORS_IR35221 option
hwmon: (acpi_power_meter) Fix potential memory leak in acpi_power_meter_add()
hwmon: (max6697) Make sure the OVERT mask is set correctly
hwmon: (pmbus) Fix page vs. register when accessing fans
hwmon: (bt1-pvt) Mark is_visible functions static
hwmon: (bt1-pvt) Define Temp- and Volt-to-N poly as maybe-unused
Merge misc fixes from Andrew Morton:
"Subsystems affected by this patch series: mm/hugetlb, samples, mm/cma,
mm/vmalloc, mm/pagealloc"
* emailed patches from Andrew Morton <[email protected]>:
mm/page_alloc: fix documentation error
vmalloc: fix the owner argument for the new __vmalloc_node_range callers
mm/cma.c: use exact_nid true to fix possible per-numa cma leak
samples/vfs: avoid warning in statx override
mm/hugetlb.c: fix pages per hugetlb calculation
Joel Savitz [Fri, 3 Jul 2020 22:15:30 +0000 (15:15 -0700)]
mm/page_alloc: fix documentation error
When I increased the upper bound of the min_free_kbytes value in ee8eb9a5fe863 ("mm/page_alloc: increase default min_free_kbytes bound") I
forgot to tweak the above comment to reflect the new value. This patch
fixes that mistake.
Barry Song [Fri, 3 Jul 2020 22:15:24 +0000 (15:15 -0700)]
mm/cma.c: use exact_nid true to fix possible per-numa cma leak
Calling cma_declare_contiguous_nid() with false exact_nid for per-numa
reservation can easily cause cma leak and various confusion. For example,
mm/hugetlb.c is trying to reserve per-numa cma for gigantic pages. But it
can easily leak cma and make users confused when system has memoryless
nodes.
In case the system has 4 numa nodes, and only numa node0 has memory. if
we set hugetlb_cma=4G in bootargs, mm/hugetlb.c will get 4 cma areas for 4
different numa nodes. since exact_nid=false in current code, all 4 numa
nodes will get cma successfully from node0, but hugetlb_cma[1 to 3] will
never be available to hugepage will only allocate memory from
hugetlb_cma[0].
In case the system has 4 numa nodes, both numa node0&2 has memory, other
nodes have no memory. if we set hugetlb_cma=4G in bootargs, mm/hugetlb.c
will get 4 cma areas for 4 different numa nodes. since exact_nid=false in
current code, all 4 numa nodes will get cma successfully from node0 or 2,
but hugetlb_cma[1] and [3] will never be available to hugepage as
mm/hugetlb.c will only allocate memory from hugetlb_cma[0] and
hugetlb_cma[2]. This causes permanent leak of the cma areas which are
supposed to be used by memoryless node.
Of cource we can workaround the issue by letting mm/hugetlb.c scan all cma
areas in alloc_gigantic_page() even node_mask includes node0 only. that
means when node_mask includes node0 only, we can get page from
hugetlb_cma[1] to hugetlb_cma[3]. But this will cause kernel crash in
free_gigantic_page() while it wants to free page by:
cma_release(hugetlb_cma[page_to_nid(page)], page, 1 << order)
On the other hand, exact_nid=false won't consider numa distance, it might
be not that useful to leverage cma areas on remote nodes. I feel it is
much simpler to make exact_nid true to make everything clear. After that,
memoryless nodes won't be able to reserve per-numa CMA from other nodes
which have memory.
Something changed recently to uncover this warning:
samples/vfs/test-statx.c:24:15: warning: `struct foo' declared inside parameter list will not be visible outside of this definition or declaration
24 | #define statx foo
| ^~~
Which is due the use of "struct statx" (here, "struct foo") in a function
prototype argument list before it has been defined:
Mike Kravetz [Fri, 3 Jul 2020 22:15:18 +0000 (15:15 -0700)]
mm/hugetlb.c: fix pages per hugetlb calculation
The routine hpage_nr_pages() was incorrectly used to calculate the number
of base pages in a hugetlb page. hpage_nr_pages is designed to be called
for THP pages and will return HPAGE_PMD_NR for hugetlb pages of any size.
Due to the context in which hpage_nr_pages was called, it is unlikely to
produce a user visible error. The routine with the incorrect call is only
exercised in the case of hugetlb memory error or migration. In addition,
this would need to be on an architecture which supports huge page sizes
less than PMD_SIZE. And, the vma containing the huge page would also need
to smaller than PMD_SIZE.
Merge tag 'pci-v5.8-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fix from Bjorn Helgaas:
"Fix a pcie_find_root_port() simplification that broke power management
because it didn't handle the edge case of finding the Root Port of a
Root Port itself (Mika Westerberg)""
* tag 'pci-v5.8-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Make pcie_find_root_port() work for Root Ports
Merge tag 'acpi-5.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"Add a new device ID for Intel Tiger Lake to the DPTF battery
participant driver (Srinivas Pandruvada) and fix the Tiger Lake fan
device ID (Sumeet Pawnikar)"
* tag 'acpi-5.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: fan: Fix Tiger Lake ACPI device ID
ACPI: DPTF: Add battery participant for TigerLake
Merge tag 'gfs2-v5.8-rc3.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2
Pull gfs2 fixes from Andreas Gruenbacher:
"Various gfs2 fixes"
* tag 'gfs2-v5.8-rc3.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
gfs2: The freeze glock should never be frozen
gfs2: When freezing gfs2, use GL_EXACT and not GL_NOCACHE
gfs2: read-only mounts should grab the sd_freeze_gl glock
gfs2: freeze should work on read-only mounts
gfs2: eliminate GIF_ORDERED in favor of list_empty
gfs2: Don't sleep during glock hash walk
gfs2: fix trans slab error when withdraw occurs inside log_flush
gfs2: Don't return NULL from gfs2_inode_lookup
exynos:
- error value and reference count fix
- error print removal
sun4i:
- remove HPD polling"
* tag 'drm-fixes-2020-07-03' of git://anongit.freedesktop.org/drm/drm: (22 commits)
drm/amdgpu: use %u rather than %d for sclk/mclk
drm/amdgpu/atomfirmware: fix vram_info fetching for renoir
drm/amd/display: Only revalidate bandwidth on medium and fast updates
drm: sun4i: hdmi: Remove extra HPD polling
drm/i915: Include asm sources for {ivb, hsw}_clear_kernel.c
drm/exynos: fix ref count leak in mic_pre_enable
drm/exynos: Properly propagate return value in drm_iommu_attach_device()
drm/exynos: Remove dev_err() on platform_get_irq() failure
drm/amd/powerplay: Fix NULL dereference in lock_bus() on Vega20 w/o RAS
dma-buf: Move dma_buf_release() from fops to dentry_ops
drm/msm: Fix up the rest of the messed up address sizes
drm/msm: Fix setup of a6xx create_address_space.
drm/msm: Fix address space size after refactor.
drm/i915/gvt: Use GFP_ATOMIC instead of GFP_KERNEL in atomic context
drm/i915/gvt: Fix incorrect check of enabled bits in mask registers
drm/i915/gvt: Fix two CFL MMIO handling caused by regression.
drm/i915/gvt: Add one missing MMIO handler for D_SKL_PLUS
drm/msm: Fix 0xfffflub in "Refactor address space initialization"
drm/msm/dpu: allow initialization of encoder locks during encoder init
drm/msm/dpu: fix error return code in dpu_encoder_init
...
arm64: Add KRYO4XX silver CPU cores to erratum list 1530923 and 1024718
KRYO4XX silver/LITTLE CPU cores with revision r1p0 are affected by
erratum 1530923 and 1024718, so add them to the respective list.
The variant and revision bits are implementation defined and are
different from the their Cortex CPU counterparts on which they are
based on, i.e., r1p0 is equivalent to rdpe.
arm64: Add KRYO4XX gold CPU cores to erratum list 1463225 and 1418040
KRYO4XX gold/big CPU core revisions r0p0 to r3p1 are affected by
erratum 1463225 and 1418040, so add them to the respective list.
The variant and revision bits are implementation defined and are
different from the their Cortex CPU counterparts on which they are
based on, i.e., (r0p0 to r3p1) is equivalent to (rcpe to rfpf).
Add MIDR value for KRYO4XX gold/big CPU cores which are
used in Qualcomm Technologies, Inc. SoCs. This will be
used to identify and apply erratum which are applicable
for these CPU cores.
Bob Peterson [Thu, 25 Jun 2020 19:42:17 +0000 (14:42 -0500)]
gfs2: The freeze glock should never be frozen
Before this patch, some gfs2 code locked the freeze glock with LM_FLAG_NOEXP
(Do not freeze) flag, and some did not. We never want to freeze the freeze
glock, so this patch makes it consistently use LM_FLAG_NOEXP always.
Bob Peterson [Thu, 25 Jun 2020 18:30:52 +0000 (13:30 -0500)]
gfs2: When freezing gfs2, use GL_EXACT and not GL_NOCACHE
Before this patch, the freeze code in gfs2 specified GL_NOCACHE in
several places. That's wrong because we always want to know the state
of whether the file system is frozen.
There was also a problem with freeze/thaw transitioning the glock from
frozen (EX) to thawed (SH) because gfs2 will normally grant glocks in EX
to processes that request it in SH mode, unless GL_EXACT is specified.
Therefore, the freeze/thaw code, which tried to reacquire the glock in
SH mode would get the glock in EX mode, and miss the transition from EX
to SH. That made it think the thaw had completed normally, but since the
glock was still cached in EX, other nodes could not freeze again.
This patch removes the GL_NOCACHE flag to allow the freeze glock to be
cached. It also adds the GL_EXACT flag so the glock is fully transitioned
from EX to SH, thereby allowing future freeze operations.
Bob Peterson [Thu, 25 Jun 2020 18:30:18 +0000 (13:30 -0500)]
gfs2: read-only mounts should grab the sd_freeze_gl glock
Before this patch, only read-write mounts would grab the freeze
glock in read-only mode, as part of gfs2_make_fs_rw. So the freeze
glock was never initialized. That meant requests to freeze, which
request the glock in EX, were granted without any state transition.
That meant you could mount a gfs2 file system, which is currently
frozen on a different cluster node, in read-only mode.
This patch makes read-only mounts lock the freeze glock in SH mode,
which will block for file systems that are frozen on another node.
Bob Peterson [Thu, 25 Jun 2020 18:29:44 +0000 (13:29 -0500)]
gfs2: freeze should work on read-only mounts
Before this patch, function freeze_go_sync, called when promoting
the freeze glock, was testing for the SDF_JOURNAL_LIVE superblock flag.
That's only set for read-write mounts. Read-only mounts don't use a
journal, so the bit is never set, so the freeze never happened.
This patch removes the check for SDF_JOURNAL_LIVE for freeze requests
but still checks it when deciding whether to flush a journal.
Bob Peterson [Wed, 17 Jun 2020 12:47:34 +0000 (07:47 -0500)]
gfs2: eliminate GIF_ORDERED in favor of list_empty
In several places, we used the GIF_ORDERED inode flag to determine
if an inode was on the ordered writes list. However, since we always
held the sd_ordered_lock spin_lock during the manipulation, we can
just as easily check list_empty(&ip->i_ordered) instead.
This allows us to keep more than one ordered writes list to make
journal writing improvements.
This patch eliminates GIF_ORDERED in favor of checking list_empty.
Merge tag 'm68knommu-for-v5.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
Pull m68knommu mm fixes from Greg Ungerer:
"Two critical mm related fixes that affect booting of m68k/ColdFire
devices.
Both fix problems caused by recent system init memblock changes"
* tag 'm68knommu-for-v5.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68k: mm: fix node memblock init
m68k: nommu: register start of the memory with memblock
Merge tag 'devicetree-fixes-for-5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
- Sync dtc to upstream to pick up fixes for I2C bus checks and quiet
warnings
- Various fixes for DT binding check warnings
- A couple of build fixes/improvements for binding checks
- ReST formatting improvements for writing-schema.rst
- Document reference fixes
* tag 'devicetree-fixes-for-5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: clock: imx: Fix e-mail address
dt-bindings: thermal: k3: Fix the reg property
dt-bindings: thermal: Remove soc unit address
dt-bindings: display: arm: versatile: Pass the sysreg unit name
dt-bindings: usb: aspeed: Remove the leading zeroes
dt-bindings: copy process-schema-examples.yaml to process-schema.yaml
dt-bindings: do not build processed-schema.yaml for 'make dt_binding_check'
dt-bindings: fix error in 'make clean' after 'make dt_binding_check'
dt-bindings: mailbox: zynqmp_ipi: fix unit address
dt-bindings: bus: uniphier-system-bus: fix warning in example
scripts/dtc: Update to upstream version v1.6.0-11-g9d7888cbf19c
doc: devicetree: bindings: fix spelling mistake
docs: dt: minor adjustments at writing-schema.rst
dt: fix reference to olpc,xo1.75-ec.txt
dt: Fix broken references to renamed docs
dt: fix broken links due to txt->yaml renames
dt: update a reference for reneases pcar file renamed to yaml
Merge tag 'for-linus-2020-07-02' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux
Pull data race annotation from Christian Brauner:
"This contains an annotation patch for a data race in copy_process()
reported by KCSAN when reading and writing nr_threads.
The data race is intentional and benign. This is obvious from the
comment above the relevant code and based on general consensus when
discussing this issue. So simply using data_race() to annotate this as
an intentional race seems the best option"
* tag 'for-linus-2020-07-02' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
fork: annotate data race in copy_process()
Merge tag 'tpmdd-next-v5.8-rc4' of git://git.infradead.org/users/jjs/linux-tpmdd
Pull tpm fixes from Jarkko Sakkinen:
"These are just fixes for bugs found lately.
All of them are small scale things here and there, and all of them are
for previous kernel releases (the oldest appeared in v2.6.17)"
* tag 'tpmdd-next-v5.8-rc4' of git://git.infradead.org/users/jjs/linux-tpmdd:
tpm_tis: Remove the HID IFX0102
tpm_tis_spi: Prefer async probe
tpm: ibmvtpm: Wait for ready buffer before probing for TPM2 attributes
tpm/st33zp24: fix spelling mistake "drescription" -> "description"
tpm_tis: extra chip->ops check on error path in tpm_tis_core_init
tpm_tis_spi: Don't send anything during flow control
tpm: Fix TIS locality timeout problems
Merge tag 'linux-kselftest-fixes-5.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest fixes from Shuah Khan:
"tpm test fixes from Jarkko Sakkinen"
* tag 'linux-kselftest-fixes-5.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: tpm: Use /bin/sh instead of /bin/bash
selftests: tpm: Use 'test -e' instead of 'test -f'
Revert "tpm: selftest: cleanup after unseal with wrong auth/policy test"
Merge tag 'linux-kselftest-kunit-fixes-5.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kunit fixes from Shuah Khan
"Fixes for build and run-times failures.
Also includes troubleshooting tips updates to kunit user
documentation"
* tag 'linux-kselftest-kunit-fixes-5.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
Documentation: kunit: Add some troubleshooting tips to the FAQ
kunit: kunit_tool: Fix invalid result when build fails
kunit: show error if kunit results are not present
kunit: kunit_config: Fix parsing of CONFIG options with space
Merge tag 'nfsd-5.8-1' of git://linux-nfs.org/~bfields/linux
Pull nfsd fixes from Bruce Fields:
"Fixes for a umask bug on exported filesystems lacking ACL support, a
leak and a module unloading bug in the /proc/fs/nfsd/clients/ code,
and a compile warning"
* tag 'nfsd-5.8-1' of git://linux-nfs.org/~bfields/linux:
SUNRPC: Add missing definition of ARCH_IMPLEMENTS_FLUSH_DCACHE_PAGE
nfsd: fix nfsdfs inode reference count leak
nfsd4: fix nfsdfs reference count loop
nfsd: apply umask on fs without ACL support
Merge tag 'block-5.8-2020-07-01' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- Use kvfree_sensitive() for the block keyslot free (Eric)
- Sync blk-mq debugfs flags (Hou)
- Memory leak fix in virtio-blk error path (Hou)
* tag 'block-5.8-2020-07-01' of git://git.kernel.dk/linux-block:
virtio-blk: free vblk-vqs in error path of virtblk_probe()
block/keyslot-manager: use kvfree_sensitive()
blk-mq-debugfs: update blk_queue_flag_name[] accordingly for new flags
Merge tag 'io_uring-5.8-2020-07-01' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
"One fix in here, for a regression in 5.7 where a task is waiting in
the kernel for a condition, but that condition won't become true until
task_work is run. And the task_work can't be run exactly because the
task is waiting in the kernel, so we'll never make any progress.
One example of that is registering an eventfd and queueing io_uring
work, and then the task goes and waits in eventfd read with the
expectation that it'll get woken (and read an event) when the io_uring
request completes. The io_uring request is finished through task_work,
which won't get run while the task is looping in eventfd read"
* tag 'io_uring-5.8-2020-07-01' of git://git.kernel.dk/linux-block:
io_uring: use signal based task_work running
task_work: teach task_work_add() to do signal_wake_up()
xen/xenbus: let xenbus_map_ring_valloc() return errno values only
Today xenbus_map_ring_valloc() can return either a negative errno
value (-ENOMEM or -EINVAL) or a grant status value. This is a mess as
e.g -ENOMEM and GNTST_eagain have the same numeric value.
Fix that by turning all grant mapping errors into -ENOENT. This is
no problem as all callers of xenbus_map_ring_valloc() only use the
return value to print an error message, and in case of mapping errors
the grant status value has already been printed by __xenbus_map_ring()
before.
xen/xenbus: avoid large structs and arrays on the stack
xenbus_map_ring_valloc() and its sub-functions are putting quite large
structs and arrays on the stack. This is problematic at runtime, but
might also result in build failures (e.g. with clang due to the option
-Werror,-Wframe-larger-than=... used).
Fix that by moving most of the data from the stack into a dynamically
allocated struct. Performance is no issue here, as
xenbus_map_ring_valloc() is used only when adding a new PV device to
a backend driver.
While at it move some duplicated code from pv/hvm specific mapping
functions to the single caller.
Jarkko Sakkinen [Thu, 25 Jun 2020 02:31:11 +0000 (05:31 +0300)]
tpm_tis: Remove the HID IFX0102
Acer C720 running Linux v5.3 reports this in klog:
tpm_tis: 1.2 TPM (device-id 0xB, rev-id 16)
tpm tpm0: tpm_try_transmit: send(): error -5
tpm tpm0: A TPM error (-5) occurred attempting to determine the timeouts
tpm_tis tpm_tis: Could not get TPM timeouts and durations
tpm_tis 00:08: 1.2 TPM (device-id 0xB, rev-id 16)
tpm tpm0: tpm_try_transmit: send(): error -5
tpm tpm0: A TPM error (-5) occurred attempting to determine the timeouts
tpm_tis 00:08: Could not get TPM timeouts and durations
ima: No TPM chip found, activating TPM-bypass!
tpm_inf_pnp 00:08: Found TPM with ID IFX0102
projects / linux.git / log