Ajit Khaparde [Fri, 1 Dec 2023 22:39:15 +0000 (14:39 -0800)]
bnxt_en: Refactor RSS capability fields
Add a new rss_cap field in the per device struct bnxt and move all
the RSS capability fields there. It will be easier to add new RSS
capabilities for the new P7 chips.
Michael Chan [Fri, 1 Dec 2023 22:39:14 +0000 (14:39 -0800)]
bnxt_en: Implement the new toggle bit doorbell mechanism on P7 chips
The new chip family passes the Toggle bits to the driver in the NQE
notification. The driver now stores this value and sends it back to
hardware when it re-arms the RX and TX CQs. Together with the earlier
patch that guarantees the driver will only re-arm the CQ at the end of
NAPI polling if it has seen a new NQE, this method allows the hardware
to detect any dropped doorbells.
Hongguang Gao [Fri, 1 Dec 2023 22:39:13 +0000 (14:39 -0800)]
bnxt_en: Consolidate DB offset calculation
The doorbell offset on P5 chips is hard coded. On the new P7 chips,
it is returned by the firmware. Simplify the logic that determines
this offset and store it in a new db_offset field in struct bnxt.
Also, provide this offset to the RoCE driver in struct bnxt_en_dev.
Michael Chan [Fri, 1 Dec 2023 22:39:12 +0000 (14:39 -0800)]
bnxt_en: Define basic P7 macros
Repurpose the BNXT_FLAG_CHIP_SR2 flag by renaming it to
BNXT_FLAG_CHIP_P7 since the SR2 chip never went to production. The SR2
statictics structure is also renamed for the P7 chip. Define the basic
P7 doorbell bits (Epoch. Toggle, etc) and implement the Epoch bit
logic. The next higher bit beyond the legal doorbell mask is the
Epoch bit used for doorbells on P7 chips. This bit is used by the
chip to detect dropped doorbells.
The 57608 chip ID belonging to the P7 family is also defined. Note
that the PCI ID is not added until the last patch in the series.
Michael Chan [Fri, 1 Dec 2023 22:39:11 +0000 (14:39 -0800)]
bnxt_en: Update firmware interface to 1.10.3.15
This updated interface supports the new 5760X P7 chip family. It has
the changes to support the new link speeds/modes and other changes
for the basic L2 features.
Michael Chan [Fri, 1 Dec 2023 22:39:10 +0000 (14:39 -0800)]
bnxt_en: Fix backing store V2 logic
The current code determines the last backing store valid type during
bnxt_hwrm_func_backing_store_qcaps_v2(). In effect, the last type
is determined based on what firmware advertises. The more correct
way is to determine it based on what the driver is configuring. The
driver may not configure all the backing store types advertised by
firmware.
Move the logic to determine the last type to bnxt_backing_store_cfg_v2().
We need to pass the legacy enable flags to the function in case only
the legacy types are being configured.
Guillaume Nault [Fri, 1 Dec 2023 14:49:52 +0000 (15:49 +0100)]
tcp: Dump bound-only sockets in inet_diag.
Walk the hashinfo->bhash2 table so that inet_diag can dump TCP sockets
that are bound but haven't yet called connect() or listen().
The code is inspired by the ->lhash2 loop. However there's no manual
test of the source port, since this kind of filtering is already
handled by inet_diag_bc_sk(). Also, a maximum of 16 sockets are dumped
at a time, to avoid running with bh disabled for too long.
There's no TCP state for bound but otherwise inactive sockets. Such
sockets normally map to TCP_CLOSE. However, "ss -l", which is supposed
to only dump listening sockets, actually requests the kernel to dump
sockets in either the TCP_LISTEN or TCP_CLOSE states. To avoid dumping
bound-only sockets with "ss -l", we therefore need to define a new
pseudo-state (TCP_BOUND_INACTIVE) that user space will be able to set
explicitly.
With an IPv4, an IPv6 and an IPv6-only socket, bound respectively to
40000, 64000, 60000, an updated version of iproute2 could work as
follow:
$ ss -t state bound-inactive
Recv-Q Send-Q Local Address:Port Peer Address:Port Process
0 0 0.0.0.0:40000 0.0.0.0:*
0 0 [::]:60000 [::]:*
0 0 *:64000 *:*
Some Micrel phys define a specific rmii-ref clock (added in 2014) while
the generic phy binding specifies an unnamed clock for ethernet phys.
This allows Micrel phys to use both, so as to keep the phys not using
the named rmii-ref clock to conform to the generic binding while allowing
them to enable a supplying clock, when the phy is not supplied by a
dedicated oscillator.
====================
Heiko Stuebner [Fri, 1 Dec 2023 15:01:31 +0000 (16:01 +0100)]
net: phy: micrel: allow usage of generic ethernet-phy clock
The generic ethernet-phy binding allows describing an external clock since
commit 350b7a258f20 ("dt-bindings: net: phy: Document support for external PHY clk")
for cases where the phy is not supplied by an oscillator but instead
by a clock from the host system.
And the old named "rmii-ref" clock from 2014 is only specified for phys
of the KSZ8021, KSZ8031, KSZ8081, KSZ8091 types.
So allow retrieving and enabling the optional generic clock on phys that
do not provide a rmii-ref clock.
Heiko Stuebner [Fri, 1 Dec 2023 15:01:30 +0000 (16:01 +0100)]
net: phy: micrel: use devm_clk_get_optional_enabled for the rmii-ref clock
While the external clock input will most likely be enabled, it's not
guaranteed and clk_get_rate in some suppliers will even just return
valid results when the clock is running.
So use devm_clk_get_optional_enabled to retrieve and enable the clock
in one go.
Jiri Pirko [Fri, 1 Dec 2023 18:01:54 +0000 (19:01 +0100)]
docs: netlink: add NLMSG_DONE message format for doit actions
In case NLMSG_DONE message is sent as a reply to doit action, multiple
kernel implementation do not send anything else than struct nlmsghdr.
Add this note to the Netlink intro documentation.
Suman Ghosh [Thu, 30 Nov 2023 03:43:23 +0000 (09:13 +0530)]
octeontx2-af: Add new mbox to support multicast/mirror offload
A new mailbox is added to support offloading of multicast/mirror
functionality. The mailbox also supports dynamic updation of the
multicast/mirror list.
David S. Miller [Sat, 2 Dec 2023 22:24:37 +0000 (22:24 +0000)]
Merge branch 'net-cacheline-optimizations'
Coco Li says:
====================
Analyze and Reorganize core Networking Structs to optimize cacheline consumption
Currently, variable-heavy structs in the networking stack is organized
chronologically, logically and sometimes by cacheline access.
This patch series attempts to reorganize the core networking stack
variables to minimize cacheline consumption during the phase of data
transfer. Specifically, we looked at the TCP/IP stack and the fast
path definition in TCP.
For documentation purposes, we also added new files for each core data
structure we considered, although not all ended up being modified due
to the amount of existing cacheline they span in the fast path. In
the documentation, we recorded all variables we identified on the
fast path and the reasons. We also hope that in the future when
variables are added/modified, the document can be referred to and
updated accordingly to reflect the latest variable organization.
Tested:
Our tests were run with neper tcp_rr using tcp traffic. The tests have $cpu
number of threads and variable number of flows (see below).
Tests were run on 6.5-rc1
Efficiency is computed as cpu seconds / throughput (one tcp_rr round trip).
The following result shows efficiency delta before and after the patch
series is applied.
v8 changes:
1. Update net_device_read_txrx cache group maximum
2. Update MAINTAINERS for documentations
3. Skip __cache_group variables in scripts/kernel-doc
====================
Coco Li [Wed, 29 Nov 2023 07:27:54 +0000 (07:27 +0000)]
netns-ipv4: reorganize netns_ipv4 fast path variables
Reorganize fast path variables on tx-txrx-rx order.
Fastpath cacheline ends after sysctl_tcp_rmem.
There are only read-only variables here. (write is on the control path
and not considered in this case)
Below data generated with pahole on x86 architecture.
Fast path variables span cache lines before change: 4
Fast path variables span cache lines after change: 2
Coco Li [Wed, 29 Nov 2023 07:27:53 +0000 (07:27 +0000)]
cache: enforce cache groups
Set up build time warnings to safeguard against future header changes of
organized structs.
Warning includes:
1) whether all variables are still in the same cache group
2) whether all the cache groups have the sum of the members size (in the
maximum condition, including all members defined in configs)
The __cache_group* variables are ignored in kernel-doc check in the
various header files they appear in to enforce the cache groups.
Coco Li [Wed, 29 Nov 2023 07:27:52 +0000 (07:27 +0000)]
Documentations: Analyze heavily used Networking related structs
Analyzed a few structs in the networking stack by looking at variables
within them that are used in the TCP/IP fast path.
Fast path is defined as TCP path where data is transferred from sender to
receiver unidirectionally. It doesn't include phases other than
TCP_ESTABLISHED, nor does it look at error paths.
We hope to re-organizing variables that span many cachelines whose fast
path variables are also spread out, and this document can help future
developers keep networking fast path cachelines small.
Optimized_cacheline field is computed as
(Fastpath_Bytes/L3_cacheline_size_x86), and not the actual organized
results (see patches to come for these).
Note how there isn't much improvement space for inet_sock and
Inet_connection_sock because sk and icsk_inet respectively takes up so
much of the struct that rest of the variables become a small portion of
the struct size.
So, we decided to reorganize tcp_sock, net_device, netns_ipv4
Niklas Söderlund [Wed, 29 Nov 2023 11:11:42 +0000 (12:11 +0100)]
net: ethernet: renesas: rcar_gen4_ptp: Depend on PTP_1588_CLOCK
When breaking out the Gen4 gPTP support to its own module the dependency
on the PTP_1588_CLOCK framework was left as optional and only stated for
the driver using the module. This leads to issues when doing
COMPILE_TEST of RENESAS_GEN4_PTP separately and PTP_1588_CLOCK is built
as a module and the other as a built-in. Add an explicit depend on
PTP_1588_CLOCK.
While at it remove the optional support for PTP_1588_CLOCK from
RENESAS_ETHER_SWITCH as the driver unconditionally calls the Gen4 gPTP
module and thus also requires the PTP_1588_CLOCK framework.
Document the IPA on the SM8650 Platform which uses version 5.5.1,
which is a minor revision of v5.5 found on SM8550, thus we can
use the SM8550 bindings as fallback since it shares the same
register mappings.
Shinas Rasheed [Wed, 29 Nov 2023 05:31:31 +0000 (21:31 -0800)]
octeon_ep: set backpressure watermark for RX queues
Set backpressure watermark for hardware RX queues. Backpressure
gets triggered when the available buffers of a hardware RX queue
falls below the set watermark. This backpressure will propagate
to packet processing pipeline in the OCTEON card, so that the host
receives fewer packets and prevents packet dropping at host.
Shinas Rasheed [Wed, 29 Nov 2023 04:53:48 +0000 (20:53 -0800)]
octeon_ep: support OCTEON CN98 devices
Add PCI Endpoint NIC support for Octeon CN98 devices.
CN98 devices are part of Octeon 9 family products with
similar PCI NIC characteristics to CN93, already supported
driver.
Add CN98 card to the device id table, as well
as support differences in the register fields and
certain usage scenarios such as unload.
Andrew Halaney [Mon, 27 Nov 2023 21:41:10 +0000 (15:41 -0600)]
net: phy: mdio_device: Reset device only when necessary
Currently the phy reset sequence is as shown below for a
devicetree described mdio phy on boot:
1. Assert the phy_device's reset as part of registering
2. Deassert the phy_device's reset as part of registering
3. Deassert the phy_device's reset as part of phy_probe
4. Deassert the phy_device's reset as part of phy_hw_init
The extra two deasserts include waiting the deassert delay afterwards,
which is adding unnecessary delay.
This applies to both possible types of resets (reset controller
reference and a reset gpio) that can be used.
Here's some snipped tracing output using the following command line
params "trace_event=gpio:* trace_options=stacktrace" illustrating
the reset handling and where its coming from:
There's a lot of paths where the device is getting its reset
asserted and deasserted. Let's track the state and only actually
do the assert/deassert when it changes.
We've added 30 non-merge commits during the last 7 day(s) which contain
a total of 58 files changed, 1598 insertions(+), 154 deletions(-).
The main changes are:
1) Add initial TX metadata implementation for AF_XDP with support in mlx5
and stmmac drivers. Two types of offloads are supported right now, that
is, TX timestamp and TX checksum offload, from Stanislav Fomichev with
stmmac implementation from Song Yoong Siang.
2) Change BPF verifier logic to validate global subprograms lazily instead
of unconditionally before the main program, so they can be guarded using
BPF CO-RE techniques, from Andrii Nakryiko.
3) Add BPF link_info support for uprobe multi link along with bpftool
integration for the latter, from Jiri Olsa.
4) Use pkg-config in BPF selftests to determine ld flags which is
in particular needed for linking statically, from Akihiko Odaki.
5) Fix a few BPF selftest failures to adapt to the upcoming LLVM18,
from Yonghong Song.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (30 commits)
bpf/tests: Remove duplicate JSGT tests
selftests/bpf: Add TX side to xdp_hw_metadata
selftests/bpf: Convert xdp_hw_metadata to XDP_USE_NEED_WAKEUP
selftests/bpf: Add TX side to xdp_metadata
selftests/bpf: Add csum helpers
selftests/xsk: Support tx_metadata_len
xsk: Add option to calculate TX checksum in SW
xsk: Validate xsk_tx_metadata flags
xsk: Document tx_metadata_len layout
net: stmmac: Add Tx HWTS support to XDP ZC
net/mlx5e: Implement AF_XDP TX timestamp and checksum offload
tools: ynl: Print xsk-features from the sample
xsk: Add TX timestamp and TX checksum offload support
xsk: Support tx_metadata_len
selftests/bpf: Use pkg-config for libelf
selftests/bpf: Override PKG_CONFIG for static builds
selftests/bpf: Choose pkg-config for the target
bpftool: Add support to display uprobe_multi links
selftests/bpf: Add link_info test for uprobe_multi link
selftests/bpf: Use bpf_link__destroy in fill_link_info tests
...
====================
Conflicts:
Documentation/netlink/specs/netdev.yaml: 839ff60df3ab ("net: page_pool: add nlspec for basic access to page pools") 48eb03dd2630 ("xsk: Add TX timestamp and TX checksum offload support")
https://lore.kernel.org/all/20231201094705.1ee3cab8@canb.auug.org.au/
While at it also regen, tree is dirty after: 48eb03dd2630 ("xsk: Add TX timestamp and TX checksum offload support")
looks like code wasn't re-rendered after "render-max" was removed.
- dpaa2: recycle the RX buffer only after all processing done
- rswitch: fix missing dev_kfree_skb_any() in error path
Previous releases - always broken:
- ipv4: fix uaf issue when receiving igmp query packet
- wifi: mac80211: fix debugfs deadlock at device removal time
- bpf:
- sockmap: af_unix stream sockets need to hold ref for pair sock
- netdevsim: don't accept device bound programs
- selftests: fix a char signedness issue
- dsa: mv88e6xxx: fix marvell 6350 probe crash
- octeontx2-pf: restore TC ingress police rules when interface is up
- wangxun: fix memory leak on msix entry
- ravb: keep reverse order of operations in ravb_remove()"
* tag 'net-6.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (51 commits)
net: ravb: Keep reverse order of operations in ravb_remove()
net: ravb: Stop DMA in case of failures on ravb_open()
net: ravb: Start TX queues after HW initialization succeeded
net: ravb: Make write access to CXR35 first before accessing other EMAC registers
net: ravb: Use pm_runtime_resume_and_get()
net: ravb: Check return value of reset_control_deassert()
net: libwx: fix memory leak on msix entry
ice: Fix VF Reset paths when interface in a failed over aggregate
bpf, sockmap: Add af_unix test with both sockets in map
bpf, sockmap: af_unix stream sockets need to hold ref for pair sock
tools: ynl-gen: always construct struct ynl_req_state
ethtool: don't propagate EOPNOTSUPP from dumps
ravb: Fix races between ravb_tx_timeout_work() and net related ops
r8169: prevent potential deadlock in rtl8169_close
r8169: fix deadlock on RTL8125 in jumbo mtu mode
neighbour: Fix __randomize_layout crash in struct neighbour
octeontx2-pf: Restore TC ingress police rules when interface is up
octeontx2-pf: Fix adding mbox work queue entry when num_vfs > 64
net: stmmac: xgmac: Disable FPE MMC interrupts
octeontx2-af: Fix possible buffer overflow
...
MMC host:
- cqhci: Fix CQE error recovery path
- sdhci-pci-gli: Fix initialization of LPM
- sdhci-sprd: Fix enabling/disabling of the vqmmc regulator"
* tag 'mmc-v6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci-sprd: Fix vqmmc not shutting down after the card was pulled
mmc: sdhci-pci-gli: Disable LPM during initialization
mmc: cqhci: Fix task clearing in CQE error recovery
mmc: cqhci: Warn of halt or task clear failure
mmc: block: Retry commands in CQE error recovery
mmc: block: Be sure to wait while busy in CQE error recovery
mmc: cqhci: Increase recovery halt timeout
mmc: block: Do not lose cache flush during CQE error recovery
Linus Torvalds [Thu, 30 Nov 2023 22:57:08 +0000 (07:57 +0900)]
Merge tag 'efi-urgent-for-v6.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi
Pull EFI fix from Ard Biesheuvel:
- Fix for EFI unaccepted memory handling
* tag 'efi-urgent-for-v6.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
efi/unaccepted: Fix off-by-one when checking for overlapping ranges
Eric Dumazet [Thu, 30 Nov 2023 09:22:59 +0000 (09:22 +0000)]
net: page_pool: fix general protection fault in page_pool_unlist
syzbot was able to trigger a crash [1] in page_pool_unlist()
page_pool_list() only inserts a page pool into a netdev page pool list
if a netdev was set in params.
Even if the kzalloc() call in page_pool_create happens to initialize
pool->user.list, I chose to be more explicit in page_pool_list()
adding one INIT_HLIST_NODE().
We could test in page_pool_unlist() if netdev was set,
but since netdev can be changed to lo, it seems more robust to
check if pool->user.list is hashed before calling hlist_del().
====================
net: ethernet: Convert to platform remove callback returning void
in (implicit) v1 of this series
(https://lore.kernel.org/netdev/20231117091655[email protected])
I tried to address the resource leaks in the three cpsw drivers. However
this is hard to get right without being able to test the changes. So
here comes a series that just converts all drivers below
drivers/net/ethernet to use .remove_new() and adds a comment about the
potential leaks for someone else to fix the problem.
See commit 5c5a7680e67b ("platform: Provide a remove callback that
returns no value") for an extended explanation and the eventual goal.
The TL;DR; is to prevent bugs like the three noticed here.
Note this series results in no change of behaviour apart from improving
the error message for the three cpsw drivers from
remove callback returned a non-zero value. This will be ignored.
to
Failed to resume device (-ESOMETHING)
====================
Uwe Kleine-König [Tue, 28 Nov 2023 17:38:28 +0000 (18:38 +0100)]
net: ethernet: ezchip: Convert to platform remove callback returning void
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Replace the error path returning a non-zero value by an error message
and a comment that there is more to do. With that this patch results in
no change of behaviour in this driver apart from improving the error
message.
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Replace the error path returning a non-zero value by an error message
and a comment that there is more to do. With that this patch results in
no change of behaviour in this driver apart from improving the error
message.
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Replace the error path returning a non-zero value by an error message
and a comment that there is more to do. With that this patch results in
no change of behaviour in this driver apart from improving the error
message.
====================
devlink: warn about existing entities during reload-reinit
Recently there has been a couple of attempts from drivers to block
devlink reload in certain situations. Turned out, the drivers do not
properly tear down ports and related netdevs during reload.
To address this, add couple of checks to be done during devlink reload
reinit action. Also, extend documentation to be more explicit.
====================
Jiri Pirko [Tue, 28 Nov 2023 11:52:55 +0000 (12:52 +0100)]
devlink: warn about existing entities during reload-reinit
During reload-reinit, all entities except for params, resources, regions
and health reporter should be removed and re-added. Add a warning to
be triggered in case the driver behaves differently.
Yujie Liu [Thu, 30 Nov 2023 03:40:18 +0000 (11:40 +0800)]
bpf/tests: Remove duplicate JSGT tests
It seems unnecessary that JSGT is tested twice (one before JSGE and one
after JSGE) since others are tested only once. Remove the duplicate JSGT
tests.
Paolo Abeni [Thu, 30 Nov 2023 09:59:10 +0000 (10:59 +0100)]
Merge branch 'net-ravb-fixes-for-the-ravb-driver'
Claudiu Beznea says:
====================
net: ravb: Fixes for the ravb driver
This series adds some fixes for ravb driver. Patches in this series
were initilly part of series at [1].
Changes in v2:
- in description of patch 1/6 documented the addition of
out_free_netdev goto label
- collected tags
- s/out_runtime_disable/out_rpm_disable in patch 2/6
- fixed typos in description of patch 6/6
Claudiu Beznea [Tue, 28 Nov 2023 08:04:39 +0000 (10:04 +0200)]
net: ravb: Keep reverse order of operations in ravb_remove()
On RZ/G3S SMARC Carrier II board having RGMII connections b/w Ethernet
MACs and PHYs it has been discovered that doing unbind/bind for ravb
driver in a loop leads to wrong speed and duplex for Ethernet links and
broken connectivity (the connectivity cannot be restored even with
bringing interface down/up). Before doing unbind/bind the Ethernet
interfaces were configured though systemd. The sh instructions used to
do unbind/bind were:
$ cd /sys/bus/platform/drivers/ravb/
$ while :; do echo 11c30000.ethernet > unbind ; \
echo 11c30000.ethernet > bind; done
It has been discovered that there is a race b/w IOCTLs initialized by
systemd at the response of success binding and the
"ravb_write(ndev, CCC_OPC_RESET, CCC)" call in ravb_remove() as
follows:
1/ as a result of bind success the user space open/configures the
interfaces tough an IOCTL; the following stack trace has been
identified on RZ/G3S:
2/ this call may execute concurrently with ravb_remove() as the
unbind/bind operation was executed in a loop
3/ if the operation mode is changed to RESET (through
ravb_write(ndev, CCC_OPC_RESET, CCC) call in ravb_remove())
while the above ravb_open() is in progress it may lead to MAC
(or PHY, or MAC-PHY connection, the right point hasn't been identified
at the moment) to be broken, thus the Ethernet connectivity fails to
restore.
The simple fix for this is to move ravb_write(ndev, CCC_OPC_RESET, CCC))
after unregister_netdev() to avoid resetting the controller while the
netdev interface is still registered.
To avoid future issues in ravb_remove(), the patch follows the proper order
of operations in ravb_remove(): reverse order compared with ravb_probe().
This avoids described races as the IOCTLs as well as unregister_netdev()
(called now at the beginning of ravb_remove()) calls rtnl_lock() before
continuing and IOCTLs check (though devinet_ioctl()) if device is still
registered just after taking the lock:
int devinet_ioctl(struct net *net, unsigned int cmd, struct ifreq *ifr)
{
// ...
rtnl_lock();
ret = -ENODEV;
dev = __dev_get_by_name(net, ifr->ifr_name);
if (!dev)
goto done;
Claudiu Beznea [Tue, 28 Nov 2023 08:04:38 +0000 (10:04 +0200)]
net: ravb: Stop DMA in case of failures on ravb_open()
In case ravb_phy_start() returns with error the settings applied in
ravb_dmac_init() are not reverted (e.g. config mode). For this call
ravb_stop_dma() on failure path of ravb_open().
Claudiu Beznea [Tue, 28 Nov 2023 08:04:37 +0000 (10:04 +0200)]
net: ravb: Start TX queues after HW initialization succeeded
ravb_phy_start() may fail. If that happens, the TX queues will remain
started. Thus, move the netif_tx_start_all_queues() after PHY is
successfully initialized.
Claudiu Beznea [Tue, 28 Nov 2023 08:04:36 +0000 (10:04 +0200)]
net: ravb: Make write access to CXR35 first before accessing other EMAC registers
Hardware manual of RZ/G3S (and RZ/G2L) specifies the following on the
description of CXR35 register (chapter "PHY interface select register
(CXR35)"): "After release reset, make write-access to this register before
making write-access to other registers (except MDIOMOD). Even if not need
to change the value of this register, make write-access to this register
at least one time. Because RGMII/MII MODE is recognized by accessing this
register".
The setup procedure for EMAC module (chapter "Setup procedure" of RZ/G3S,
RZ/G2L manuals) specifies the E-MAC.CXR35 register is the first EMAC
register that is to be configured.
Note [A] from chapter "PHY interface select register (CXR35)" specifies
the following:
[A] The case which CXR35 SEL_XMII is used for the selection of RGMII/MII
in APB Clock 100 MHz.
(1) To use RGMII interface, Set ‘H’03E8_0000’ to this register.
(2) To use MII interface, Set ‘H’03E8_0002’ to this register.
Claudiu Beznea [Tue, 28 Nov 2023 08:04:35 +0000 (10:04 +0200)]
net: ravb: Use pm_runtime_resume_and_get()
pm_runtime_get_sync() may return an error. In case it returns with an error
dev->power.usage_count needs to be decremented. pm_runtime_resume_and_get()
takes care of this. Thus use it.
Claudiu Beznea [Tue, 28 Nov 2023 08:04:34 +0000 (10:04 +0200)]
net: ravb: Check return value of reset_control_deassert()
reset_control_deassert() could return an error. Some devices cannot work
if reset signal de-assert operation fails. To avoid this check the return
code of reset_control_deassert() in ravb_probe() and take proper action.
Along with it, the free_netdev() call from the error path was moved after
reset_control_assert() on its own label (out_free_netdev) to free
netdev in case reset_control_deassert() fails.
====================
tcp: Clean up and refactor cookie_v[46]_check().
This is a preparation series for upcoming arbitrary SYN Cookie
support with BPF. [0]
There are slight differences between cookie_v[46]_check(). Such a
discrepancy caused an issue in the past, and BPF SYN Cookie support
will add more churn.
The primary purpose of this series is to clean up and refactor
cookie_v[46]_check() to minimise such discrepancies and make the
BPF series easier to review.
tcp: Factorise cookie-dependent fields initialisation in cookie_v[46]_check()
We will support arbitrary SYN Cookie with BPF, and then kfunc at
TC will preallocate reqsk and initialise some fields that should
not be overwritten later by cookie_v[46]_check().
To simplify the flow in cookie_v[46]_check(), we move such fields'
initialisation to cookie_tcp_reqsk_alloc() and factorise non-BPF
SYN Cookie handling into cookie_tcp_check(), where we validate the
cookie and allocate reqsk, as done by kfunc later.
Note that we set ireq->ecn_ok in two steps, the latter of which will
be shared by the BPF case. As cookie_ecn_ok() is one-liner, now
it's inlined.
tcp: Factorise cookie-independent fields initialisation in cookie_v[46]_check().
We will support arbitrary SYN Cookie with BPF, and then some reqsk fields
are initialised in kfunc, and others are done in cookie_v[46]_check().
This patch factorises the common part as cookie_tcp_reqsk_init() and
calls it in cookie_tcp_reqsk_alloc() to minimise the discrepancy between
cookie_v[46]_check().
tcp: Move TCP-AO bits from cookie_v[46]_check() to tcp_ao_syncookie().
We initialise treq->af_specific in cookie_tcp_reqsk_alloc() so that
we can look up a key later in tcp_create_openreq_child().
Initially, that change was added for MD5 by commit ba5a4fdd63ae ("tcp:
make sure treq->af_specific is initialized"), but it has not been used
since commit d0f2b7a9ca0a ("tcp: Disable header prediction for MD5
flow.").
Now, treq->af_specific is used only by TCP-AO, so, we can move that
initialisation into tcp_ao_syncookie().
In addition to that, l3index in cookie_v[46]_check() is only used for
tcp_ao_syncookie(), so let's move it as well.
While at it, we move down tcp_ao_syncookie() in cookie_v4_check() so
that it will be called after security_inet_conn_request() to make
functions order consistent with cookie_v6_check().
tcp: Don't initialise tp->tsoffset in tcp_get_cookie_sock().
When we create a full socket from SYN Cookie, we initialise
tcp_sk(sk)->tsoffset redundantly in tcp_get_cookie_sock() as
the field is inherited from tcp_rsk(req)->ts_off.
Jiawen Wu [Tue, 28 Nov 2023 09:59:28 +0000 (17:59 +0800)]
net: libwx: fix memory leak on msix entry
Since pci_free_irq_vectors() set pdev->msix_enabled as 0 in the
calling of pci_msix_shutdown(), wx->msix_entries is never freed.
Reordering the lines to fix the memory leak.
====================
mptcp: More selftest coverage and code cleanup for net-next
Patches 1-5 and 7-8 add selftest coverage (and an associated subflow
counter in the kernel) to validate the recently-updated handling of
subflows with ID 0.
Patch 6 renames a label in the userspace path manager for clarity.
Patches 9-11 and 13-15 factor out common selftest code by moving certain
functions to mptcp_lib.sh
Patch 12 makes sure the random data file generated for selftest
payloads has the intended size.
To avoid duplicated code in different MPTCP selftests, we can add
and use helpers defined in mptcp_lib.sh.
wait_local_port_listen() helper is defined in diag.sh, mptcp_connect.sh,
mptcp_join.sh and simult_flows.sh, export it into mptcp_lib.sh and
rename it with mptcp_lib_ prefix. Use this new helper in all these
scripts.
Note: We only have IPv4 connections in this helper, not looking at IPv6
(tcp6) but that's OK because we only have IPv4 connections here in diag.sh.
Geliang Tang [Tue, 28 Nov 2023 23:18:58 +0000 (15:18 -0800)]
selftests: mptcp: add mptcp_lib_check_transfer
To avoid duplicated code in different MPTCP selftests, we can add
and use helpers defined in mptcp_lib.sh.
check_transfer() and print_file_err() helpers are defined both in
mptcp_connect.sh and mptcp_sockopt.sh, export them into mptcp_lib.sh
and rename them with mptcp_lib_ prefix. And use them in all scripts.
Note: In mptcp_sockopt.sh it is OK to drop 'ret=1' in check_transfer()
because it will be set in run_tests() anyway.
Geliang Tang [Tue, 28 Nov 2023 23:18:57 +0000 (15:18 -0800)]
selftests: mptcp: add mptcp_lib_make_file
To avoid duplicated code in different MPTCP selftests, we can add
and use helpers defined in mptcp_lib.sh.
make_file() helper in mptcp_sockopt.sh and userspace_pm.sh are the same.
Export it into mptcp_lib.sh and rename it as mptcp_lib_kill_wait(). Use
it in both mptcp_connect.sh and mptcp_join.sh.
Geliang Tang [Tue, 28 Nov 2023 23:18:56 +0000 (15:18 -0800)]
selftests: mptcp: add missing oflag=append
In mptcp_connect.sh we are missing something like "oflag=append"
because this will write "${rem}" bytes at the beginning of the file
where there is already some random bytes. It should write that at
the end.
This patch adds this missing 'oflag=append' flag for 'dd' command in
make_file().
Geliang Tang [Tue, 28 Nov 2023 23:18:55 +0000 (15:18 -0800)]
selftests: mptcp: add mptcp_lib_get_counter
To avoid duplicated code in different MPTCP selftests, we can add
and use helpers defined in mptcp_lib.sh.
The helper get_counter() in mptcp_join.sh and get_mib_counter() in
mptcp_connect.sh have the same functionality, export get_counter() into
mptcp_lib.sh and rename it as mptcp_lib_get_counter(). Use this new
helper instead of get_counter() and get_mib_counter().
Use this helper in test_prio() in userspace_pm.sh too instead of
open-coding.
Geliang Tang [Tue, 28 Nov 2023 23:18:54 +0000 (15:18 -0800)]
selftests: mptcp: add mptcp_lib_is_v6
To avoid duplicated code in different MPTCP selftests, we can add
and use helpers defined in mptcp_lib.sh.
is_v6() helper is defined in mptcp_connect.sh, mptcp_join.sh and
mptcp_sockopt.sh, so export it into mptcp_lib.sh and rename it as
mptcp_lib_is_v6(). Use this new helper in all scripts.
Geliang Tang [Tue, 28 Nov 2023 23:18:53 +0000 (15:18 -0800)]
selftests: mptcp: add mptcp_lib_kill_wait
To avoid duplicated code in different MPTCP selftests, we can add
and use helpers defined in mptcp_lib.sh.
Export kill_wait() helper in userspace_pm.sh into mptcp_lib.sh and
rename it as mptcp_lib_kill_wait(). It can be used to instead of
kill_wait() in mptcp_join.sh. Use the new helper in both scripts.
Geliang Tang [Tue, 28 Nov 2023 23:18:49 +0000 (15:18 -0800)]
selftests: mptcp: userspace pm create id 0 subflow
This patch adds a selftest to create id 0 subflow. Pass id 0 to the
helper userspace_pm_add_sf() to create id 0 subflow. chk_mptcp_info
shows one subflow but chk_subflows_total shows two subflows in each
namespace.
Geliang Tang [Tue, 28 Nov 2023 23:18:48 +0000 (15:18 -0800)]
selftests: mptcp: update userspace pm test helpers
This patch adds a new argument namespace to userspace_pm_add_addr() and
userspace_pm_add_sf() to make these two helper more versatile.
Add two more versatile helpers for userspace pm remove subflow or address:
userspace_pm_rm_addr() and userspace_pm_rm_sf(). The original test helpers
userspace_pm_rm_sf_addr_ns1() and userspace_pm_rm_sf_addr_ns2() can be
replaced by these new helpers.
Geliang Tang [Tue, 28 Nov 2023 23:18:47 +0000 (15:18 -0800)]
selftests: mptcp: add chk_subflows_total helper
This patch adds a new helper chk_subflows_total(), in it use the newly
added counter mptcpi_subflows_total to get the "correct" amount of
subflows, including the initial one.
To be compatible with old 'ss' or kernel versions not supporting this
counter, get the total subflows by listing TCP connections that are
MPTCP subflows:
ss -ti state state established state syn-sent state syn-recv |
grep -c tcp-ulp-mptcp.
Geliang Tang [Tue, 28 Nov 2023 23:18:46 +0000 (15:18 -0800)]
selftests: mptcp: add evts_get_info helper
This patch adds a new helper get_info_value(), using 'sed' command to
parse the value of the given item name in the line with the given keyword,
to make chk_mptcp_info() and pedit_action_pkts() more readable.
Also add another helper evts_get_info() to use get_info_value() to parse
the output of 'pm_nl_ctl events' command, to make all the userspace pm
selftests more readable, both in mptcp_join.sh and userspace_pm.sh.
Geliang Tang [Tue, 28 Nov 2023 23:18:45 +0000 (15:18 -0800)]
mptcp: add mptcpi_subflows_total counter
If the initial subflow has been removed, we cannot know without checking
other counters, e.g. ss -ti <filter> | grep -c tcp-ulp-mptcp or
getsockopt(SOL_MPTCP, MPTCP_FULL_INFO, ...) (or others except MPTCP_INFO
of course) and then check mptcp_subflow_data->num_subflows to get the
total amount of subflows.
This patch adds a new counter mptcpi_subflows_total in mptcpi_flags to
store the total amount of subflows, including the initial one. A new
helper __mptcp_has_initial_subflow() is added to check whether the
initial subflow has been removed or not. With this helper, we can then
compute the total amount of subflows from mptcp_info by doing something
like:
Jakub Kicinski [Thu, 30 Nov 2023 04:03:27 +0000 (20:03 -0800)]
Merge branch 'mlxsw-support-cff-flood-mode'
Petr Machata says:
====================
mlxsw: Support CFF flood mode
The registers to configure to initialize a flood table differ between the
controlled and CFF flood modes. In therefore needs to be an op. Add it,
hook up the current init to the existing families, and invoke the op.
PGT is an in-HW table that maps addresses to sets of ports. Then when some
HW process needs a set of ports as an argument, instead of embedding the
actual set in the dynamic configuration, what gets configured is the
address referencing the set. The HW then works with the appropriate PGT
entry.
Among other allocations, the PGT currently contains two large blocks for
bridge flooding: one for 802.1q and one for 802.1d. Within each of these
blocks are three tables, for unknown-unicast, multicast and broadcast
flooding:
. . . | 802.1q | 802.1d | . . .
| UC | MC | BC | UC | MC | BC |
\______ _____/ \_____ ______/
v v
FID flood vectors
Thus each FID (which corresponds to an 802.1d bridge or one VLAN in an
802.1q bridge) uses three flood vectors spread across a fairly large region
of PGT.
This way of organizing the flood table (called "controlled") is not very
flexible. E.g. to decrease a bridge scale and store more IP MC vectors, one
would need to completely rewrite the bridge PGT blocks, or resort to hacks
such as storing individual MC flood vectors into unused part of the bridge
table.
In order to address these shortcomings, Spectrum-2 and above support what
is called CFF flood mode, for Compressed FID Flooding. In CFF flood mode,
each FID has a little table of its own, with three entries adjacent to each
other, one for unknown-UC, one for MC, one for BC. This allows for a much
more fine-grained approach to PGT management, where bits of it are
allocated on demand.
Besides the FID table organization, the CFF flood mode also impacts Router
Subport (RSP) table. This table contains flood vectors for rFIDs, which are
FIDs that reference front panel ports or LAGs. The RSP table contains two
entries per front panel port and LAG, one for unknown-UC traffic, and one
for everything else. Currently, the FW allocates and manages the table in
its own part of PGT. rFIDs are marked with flood_rsp bit and managed
specially. In CFF mode, rFIDs are managed as all other FIDs. The driver
therefore has to allocate and maintain the flood vectors. Like with bridge
FIDs, this is more work, but increases flexibility of the system.
The FW currently supports both the controlled and CFF flood modes. To shed
complexity, in the future it should only support CFF flood mode. Hence this
patchset, which adds CFF flood mode support to mlxsw.
Since mlxsw needs to maintain both the controlled mode as well as CFF mode
support, we will keep the layout as compatible as possible. The bridge
tables will stay in the same overall shape, just their inner organization
will change from flood mode -> FID to FID -> flood mode. Likewise will RSP
be kept as a contiguous block of PGT memory, as was the case when the FW
maintained it.
- The way FIDs get configured under the CFF flood mode differs from the
currently used controlled mode. The simple approach of having several
globally visible arrays for spectrum.c to statically choose from no
longer works.
Patch #1 thus privatizes all FID initialization and finalization logic,
and exposes it as ops instead.
- Patch #2 renames the ops that are specific to the controlled mode, to
make room in the namespace for the CFF variants.
Patch #3 extracts a helper to compute flood table base out of
mlxsw_sp_fid_flood_table_mid().
- The op fid_setup configured fid_offset, i.e. the number of this FID
within its family. For rFIDs in CFF mode, to determine this number, the
driver will need to do fallible queries.
Thus in patch #4, make the FID setup operation fallible as well.
- Flood mode initialization routine differs between the controlled and CFF
flood modes. The controlled mode needs to configure flood table layout,
which the CFF mode does not need to do.
In patch #5, move mlxsw_sp_fid_flood_table_init() up so that the
following patch can make use of it.
In patch #6, add an op to be invoked per table (if defined).
- The current way of determining PGT allocation size depends on the number
of FIDs and number of flood tables. RFIDs however have PGT footprint
depending not on number of FIDs, but on number of ports and LAGs, because
which ports an rFID should flood to does not depend on the FID itself,
but on the port or LAG that it references.
Therefore in patch #7, add FID family ops for determining PGT allocation
size.
- As elaborated above, layout of PGT will differ between controlled and CFF
flood modes. In CFF mode, it will further differ between rFIDs and other
FIDs (as described at previous patch). The way to pack the SFMR register
to configure a FID will likewise differ from controlled to CFF.
Thus in patches #8 and #9 add FID family ops to determine PGT base
address for a FID and to pack SFMR.
- Patches #10 and #11 add more bits for RSP support. In patch #10, add a
new traffic type enumerator, for non-UC traffic. This is a combination of
BC and MC traffic, but the way that mlxsw maps these mnemonic names to
actual traffic type configurations requires that we have a new name to
describe this class of traffic.
Patch #11 then adds hooks necessary for RSP table maintenance. As ports
come and go, and join and leave LAGs, it is necessary to update flood
vectors that the rFIDs use. These new hooks will make that possible.
- Patches #12, #13 and #14 introduce flood profiles. These have been
implicit so far, but the way that CFF flood mode works with profile IDs
requires that we make them explicit.
Thus in patch #12, introduce flood profile objects as a set of flood
tables that FID families then refer to. The FID code currently only
uses a single flood profile.
In patch #13, add a flood profile ID to flood profile objects.
In patch #14, when in CFF mode, configure SFFP according to the existing
flood profiles (or the one that exists as of that point).
- Patches #15 and #16 add code to implement, respectively, bridge FIDs and
RSP FIDs in CFF mode.
- In patch #17, toggle flood_mode_prefer_cff on Spectrum-2 and above, which
makes the newly-added code live.
====================
Petr Machata [Tue, 28 Nov 2023 15:50:49 +0000 (16:50 +0100)]
mlxsw: spectrum_fid: Add support for rFID family in CFF flood mode
In this patch, add the artifacts for the rFID family that works in CFF
flood mode.
The same that was said about PGT organization and lookup in bridge FID
families applies for the rFID family as well. The main difference lies in
the fact that in the controlled flood mode, the FW was taking care of
maintaining the PGT tables for rFIDs. In CFF mode, the responsibility
shifts to the driver.
All rFIDs are based off either a front panel port, or a LAG port. For those
based off ports, we need to maintain at worst one PGT block for each port,
for those based off LAGs, one PGT block per LAG. This reflects in the
pgt_size callback, which determines the PGT footprint based on number of
ports and the LAG capacity.
A number of FIDs may end up using the same PGT base. Unlike with bridges,
where membership of a port in a given FID is highly dynamic, an rFID based
of a port will just always need to flood to that port.
Both the port and the LAG subtables need to be actively maintained. To that
end, the CFF rFID family implements fid_port_init and fid_port_fini
callbacks, which toggle the necessary bits.
Both FID-MID translation and SFMR packing then point into either the port
or the LAG subtable, to the block that corresponds to a given port or a
given LAG, depending on what port the RIF bound to the rFID uses.
As in the previous patch, the way CFF flood mode organizes PGT accesses
allows for much more smarts and dynamism. As in the previous patch, we
rather aim to keep things simple and static.
Petr Machata [Tue, 28 Nov 2023 15:50:48 +0000 (16:50 +0100)]
mlxsw: spectrum_fid: Add a family for bridge FIDs in CFF flood mode
In this patch, add the artifacts for 802.1d and 802.1q FID families that
work in CFF flood mode.
In CFF flood mode, the way flood vectors are looked up changes: there's a
per-FID PGT base, to which a small offset is added depending on type of
traffic. Thus each FID occupies a small contiguous block of PGT memory,
whereas in the controlled flood mode, flood vectors for a given FID were
spread across the PGT.
The term "flood table" as used by the spectrum_fid module, borrows from
controlled flood mode way of organizing the PGT table. There flood tables
were actual tables, contiguous in the PGT. In the CFF flood mode, they are
more abstract: a flood table becomes a collection of e.g. all first rows of
the per-FID PGT blocks. Nonetheless we retain the nomenclature.
FIDs are still configured through the SFMR register, but there are
different fields to set under CFF mode: PGT base and profile. Thus register
packing gets a dedicated op overload as well.
The new organization of PGT makes it possible to treat the PGT as a block
of an ordinary memory, allocate and deallocate on demand, and achieve
better flexibility. Here instead, we aim to keep the code as close as
possible to the previous controlled flood mode, support for which we need
to retain for Spectrum-1 and older FW versions anyway. Thus the PGT
footprint of the individual families is the same as before, just the
internal organization of the per-family PGT region differs. Hence the
pgt_size callback is reused between the controlled and CFF flood modes.
Since the dummy family has no flood tables in either the CTL mode or in
CFF mode, the existing one can be reused for the CFF family array.
Users should not notice any changes between the controlled and CFF flood
modes.
Petr Machata [Tue, 28 Nov 2023 15:50:47 +0000 (16:50 +0100)]
mlxsw: spectrum_fid: Initialize flood profiles in CFF mode
In CFF flood mode, the way flood vectors are looked up changes: there's a
per-FID PGT base, to which a small offset is added depending on type of
traffic. Thus each FID occupies a small contiguous block of PGT memory,
whereas in the controlled flood mode, flood vectors for a given FID were
spread across the PGT.
Each FID is associated with one of a handful of profiles. The profile and
the traffic type are then used as keys to look up the PGT offset. This
offset is then added to the per-FID PGT base. The profile / type / offset
mapping needs to be configured by the driver, and is only relevant in CFF
flood mode.
In this patch, add the SFFP initialization code. Only initialize the one
profile currently explicitly used. As follow-up patch add more profiles,
this code will pick them up and initialize as well.
Petr Machata [Tue, 28 Nov 2023 15:50:46 +0000 (16:50 +0100)]
mlxsw: spectrum_fid: Add profile_id to flood profile
In the CFF mode, flood profiles are identified by a unique numerical
identifier. This is used for configuration of FIDs and for configuration of
traffic-type to PGT offset rules. In both cases, the numerical identifier
serves as a handle for the flood profile. Add the identifier to the flood
profile structure.
There is currently only one flood profile in use explicitly, the one used
for all bridging. Eventually three will be necessary in total: one for
bridges, one for rFIDs, one for NVE underlay. A total of four profiles
are supported by the HW. Start allocating at 1, because 0 is currently
used for underlay NVE flood.
Petr Machata [Tue, 28 Nov 2023 15:50:45 +0000 (16:50 +0100)]
mlxsw: spectrum_fid: Add an object to keep flood profiles
A flood profile is a mapping from traffic type to an offset at which a
flood vector should be looked up. In mlxsw so far, a flood profile was
somewhat implicitly represented by flood table array. When the CFF flood
mode will be introduced, the flood profile will become more explicit: each
will get a number and the profile ID / traffic-type / offset mapping will
actually need to be initialized in the hardware.
Therefore it is going to be handy to have a structure that keeps all the
components that compose a flood profile. Add this structure, currently with
just the flood table array bits. In the FID families that flood at all,
reference the flood profile instead of just the table array.
Petr Machata [Tue, 28 Nov 2023 15:50:44 +0000 (16:50 +0100)]
mlxsw: spectrum_fid: Add hooks for RSP table maintenance
In the CFF flood mode, the driver has to allocate a table within PGT, which
holds flood vectors for router subport FIDs. For LAGs, these flood vectors
have to obviously be maintained dynamically as port membership in a LAG
changes. But even for physical ports, the flood vectors have to be kept
valid, and may not contain enabled bits corresponding to non-existent
ports. It is therefore not possible to precompute the port part of the RSP
table, it has to be maintained as ports come and go due to splits.
To support the RSP table maintenance, add to FID ops two new ops:
fid_port_init and fid_port_fini, for when a port comes to existence, or
joins a lag, and vice versa. Invoke these ops from
mlxsw_sp_port_fids_init() and mlxsw_sp_port_fids_fini(), which are called
when port is added and removed, respectively. Also add two new hooks for
LAG maintenance, mlxsw_sp_fid_port_join_lag() / _leave_lag() which
transitively call into the same ops.
Later patches will actually add the op implementations themselves, this
just adds the scaffolding.
Petr Machata [Tue, 28 Nov 2023 15:50:43 +0000 (16:50 +0100)]
mlxsw: spectrum_fid: Add a not-UC packet type
In CFF flood mode, the rFID family will allocate two tables. One for
unknown UC traffic, one for everything else. Add a traffic type for the
everything else traffic.
projects / linux.git / log