Frieder Schrempf [Mon, 22 Feb 2021 11:52:20 +0000 (12:52 +0100)]
regulator: pca9450: Clear PRESET_EN bit to fix BUCK1/2/3 voltage setting
The driver uses the DVS registers PCA9450_REG_BUCKxOUT_DVS0 to set the
voltage for the buck regulators 1, 2 and 3. This has no effect as the
PRESET_EN bit is set by default and therefore the preset values are used
instead, which are set to 850 mV.
To fix this we clear the PRESET_EN bit at time of initialization.
Takashi Iwai [Wed, 10 Mar 2021 11:28:09 +0000 (12:28 +0100)]
ALSA: hda/hdmi: Cancel pending works before suspend
The per_pin->work might be still floating at the suspend, and this may
hit the access to the hardware at an unexpected timing. Cancel the
work properly at the suspend callback for avoiding the buggy access.
Note that the bug doesn't trigger easily in the recent kernels since
the work is queued only when the repoll count is set, and usually it's
only at the resume callback, but it's still possible to hit in
theory.
Takashi Iwai [Wed, 10 Mar 2021 11:28:08 +0000 (12:28 +0100)]
ALSA: hda: Avoid spurious unsol event handling during S3/S4
When HD-audio bus receives unsolicited events during its system
suspend/resume (S3 and S4) phase, the controller driver may still try
to process events although the codec chips are already (or yet)
powered down. This might screw up the codec communication, resulting
in CORB/RIRB errors. Such events should be rather skipped, as the
codec chip status such as the jack status will be fully refreshed at
the system resume time.
Since we're tracking the system suspend/resume state in codec
power.power_state field, let's add the check in the common unsol event
handler entry point to filter out such events.
Takashi Iwai [Wed, 10 Mar 2021 11:28:07 +0000 (12:28 +0100)]
ALSA: hda: Flush pending unsolicited events before suspend
The HD-audio controller driver processes the unsolicited events via
its work asynchronously, and this might be pending when the system
goes to suspend. When a lengthy event handling like ELD byte reads is
running, this might trigger unexpected accesses among suspend/resume
procedure, typically seen with Nvidia driver that still requires the
handling via unsolicited event verbs for ELD updates.
This patch adds the flush of unsol_work to assure that pending events
are processed before going into suspend.
Commit 0fdf1bb75953 ("arm64: perf: Avoid PMXEV* indirection") changed
armv8pmu_read_evcntr() to return a u32 instead of u64. The result is
silent truncation of the event counter when using 64-bit counters. Given
the offending commit appears to have passed thru several folks, it seems
likely this was a bad rebase after v8.5 PMU 64-bit counters landed.
James Morse [Wed, 10 Mar 2021 05:53:10 +0000 (11:23 +0530)]
arm64/mm: Fix __enable_mmu() for new TGRAN range values
As per ARM ARM DDI 0487G.a, when FEAT_LPA2 is implemented, ID_AA64MMFR0_EL1
might contain a range of values to describe supported translation granules
(4K and 16K pages sizes in particular) instead of just enabled or disabled
values. This changes __enable_mmu() function to handle complete acceptable
range of values (depending on whether the field is signed or unsigned) now
represented with ID_AA64MMFR0_TGRAN_SUPPORTED_[MIN..MAX] pair. While here,
also fix similar situations in EFI stub and KVM as well.
Catalin Marinas [Tue, 9 Mar 2021 12:26:01 +0000 (12:26 +0000)]
arm64: mte: Map hotplugged memory as Normal Tagged
In a system supporting MTE, the linear map must allow reading/writing
allocation tags by setting the memory type as Normal Tagged. Currently,
this is only handled for memory present at boot. Hotplugged memory uses
Normal non-Tagged memory.
Introduce pgprot_mhp() for hotplugged memory and use it in
add_memory_resource(). The arm64 code maps pgprot_mhp() to
pgprot_tagged().
Note that ZONE_DEVICE memory should not be mapped as Tagged and
therefore setting the memory type in arch_add_memory() is not feasible.
Peter Zijlstra [Tue, 9 Mar 2021 14:21:18 +0000 (15:21 +0100)]
seqlock,lockdep: Fix seqcount_latch_init()
seqcount_init() must be a macro in order to preserve the static
variable that is used for the lockdep key. Don't then wrap it in an
inline function, which destroys that.
Luckily there aren't many users of this function, but fix it before it
becomes a problem.
results in lockdep getting confused between the RX and TX stats lock.
This is because u64_stats_init() is an inline calling seqcount_init(),
which is a macro using a static variable to generate a lockdep class.
By wrapping that in an inline, we negate the effect of the macro and
fold the static key variable, hence the confusion.
Fix by also making u64_stats_init() a macro for the case where it
matters, leaving the other case an inline for argument validation
etc.
Yejune Deng [Wed, 10 Mar 2021 07:49:01 +0000 (15:49 +0800)]
virt: acrn: Use EPOLLIN instead of POLLIN
This fixes the following sparse warning:
"sparse warnings: (new ones prefixed by >>)"
>> drivers/virt/acrn/irqfd.c:163:13: sparse: sparse: restricted __poll_t
degrades to integer
Serge Semin [Fri, 12 Feb 2021 20:55:19 +0000 (23:55 +0300)]
usb: dwc3: qcom: Add missing DWC3 OF node refcount decrement
of_get_child_by_name() increments the reference counter of the OF node it
managed to find. So after the code is done using the device node, the
refcount must be decremented. Add missing of_node_put() invocation then
to the dwc3_qcom_of_register_core() method, since DWC3 OF node is being
used only there.
Pete Zaitcev [Thu, 4 Mar 2021 04:10:53 +0000 (22:10 -0600)]
USB: usblp: fix a hang in poll() if disconnected
Apparently an application that opens a device and calls select()
on it, will hang if the decice is disconnected. It's a little
surprising that we had this bug for 15 years, but apparently
nobody ever uses select() with a printer: only write() and read(),
and those work fine. Well, you can also select() with a timeout.
The fix is modeled after devio.c. A few other drivers check the
condition first, then do not add the wait queue in case the
device is disconnected. We doubt that's completely race-free.
So, this patch adds the process first, then locks properly
and checks for the disconnect.
Wei Yongjun [Fri, 5 Mar 2021 03:49:27 +0000 (03:49 +0000)]
USB: gadget: udc: s3c2410_udc: fix return value check in s3c2410_udc_probe()
In case of error, the function devm_platform_ioremap_resource()
returns ERR_PTR() and never returns NULL. The NULL test in the
return value check should be replaced with IS_ERR().
usb: renesas_usbhs: Clear PIPECFG for re-enabling pipe with other EPNUM
According to the datasheet, this controller has a restriction
which "set an endpoint number so that combinations of the DIR bit and
the EPNUM bits do not overlap.". However, since the udc core driver is
possible to assign a bulk pipe as an interrupt endpoint, an endpoint
number may not match the pipe number. After that, when user rebinds
another gadget driver, this driver broke the restriction because
the driver didn't clear any configuration in usb_ep_disable().
Example:
# modprobe g_ncm
Then, EP3 = pipe 3, EP4 = pipe 4, EP5 = pipe 6
# rmmod g_ncm
# modprobe g_hid
Then, EP3 = pipe 6, EP4 = pipe 7.
So, pipe 3 and pipe 6 are set as EP3.
usb: dwc3: qcom: Honor wakeup enabled/disabled state
The dwc3-qcom currently enables wakeup interrupts unconditionally
when suspending, however this should not be done when wakeup is
disabled (e.g. through the sysfs attribute power/wakeup). Only
enable wakeup interrupts when device_may_wakeup() returns true.
Ruslan Bilovol [Mon, 1 Mar 2021 11:49:31 +0000 (13:49 +0200)]
usb: gadget: f_uac2: always increase endpoint max_packet_size by one audio slot
As per UAC2 Audio Data Formats spec (2.3.1.1 USB Packets),
if the sampling rate is a constant, the allowable variation
of number of audio slots per virtual frame is +/- 1 audio slot.
It means that endpoint should be able to accept/send +1 audio
slot.
Previous endpoint max_packet_size calculation code
was adding sometimes +1 audio slot due to DIV_ROUND_UP
behaviour which was rounding up to closest integer.
However this doesn't work if the numbers are divisible.
It had no any impact with Linux hosts which ignore
this issue, but in case of more strict Windows it
caused rejected enumeration
Thus always add +1 audio slot to endpoint's max packet size
Shawn Guo [Mon, 1 Mar 2021 07:57:45 +0000 (15:57 +0800)]
usb: dwc3: qcom: add ACPI device id for sc8180x
It enables USB Host support for sc8180x ACPI boot, both the standalone
one and the one behind URS (USB Role Switch). And they share the
the same dwc3_acpi_pdata with sdm845.
Yorick de Wid [Sat, 13 Feb 2021 14:49:02 +0000 (15:49 +0100)]
Goodix Fingerprint device is not a modem
The CDC ACM driver is false matching the Goodix Fingerprint device
against the USB_CDC_ACM_PROTO_AT_V25TER.
The Goodix Fingerprint device is a biometrics sensor that should be
handled in user-space. libfprint has some support for Goodix
fingerprint sensors, although not for this particular one. It is
possible that the vendor allocates a PID per OEM (Lenovo, Dell etc).
If this happens to be the case then more devices from the same vendor
could potentially match the ACM modem module table.
Our SOF/audio CI shows an across-the-board regression when we try v5.12-rc1,
specifically on pause/resume tests with an interactive terminal running 'aplay
-i' commands managed by expect to simulate the user pressing the space bar to
pause/unpause. It turns out the processes are not longer killed and the audio
devices remain busy (see publicly available test results listed below).
git bisect points to commit 33d4ae9885987 ("drivers:tty:pty: Fix a race
causing data loss on close"). Reverting the patch fixes the issue on all test
devices.
Further analysis with Corey Minyard points to a problem where a slave tty will
not get a SIGHUP when the master is closed.
FIFO is triggered 4 intervals after receiving a byte, it's good
when we don't care about the time of reception, but are only
interested in the presence of any activity on the line.
Unfortunately, this method is not suitable for all tasks,
for example, the RS-485 protocol will not work properly,
since the state machine must track the request-response time
and after the timeout expires, a decision is made that the device
on the line is not responding.
Uwe Kleine-König [Fri, 19 Feb 2021 13:33:07 +0000 (14:33 +0100)]
leds: trigger/tty: Use led_set_brightness_sync() from workqueue
led_set_brightness() involves scheduling a workqueue. As here the led's
brightness setting is done in context of the trigger's workqueue this is
unjustified overhead and it's more sensible to use
led_set_brightness_sync().
Dan Carpenter [Fri, 5 Mar 2021 08:56:32 +0000 (11:56 +0300)]
staging: rtl8188eu: fix potential memory corruption in rtw_check_beacon_data()
The "ie_len" is a value in the 1-255 range that comes from the user. We
have to cap it to ensure that it's not too large or it could lead to
memory corruption.
Ian Abbott [Tue, 23 Feb 2021 14:30:55 +0000 (14:30 +0000)]
staging: comedi: pcl726: Use 16-bit 0 for interrupt data
The pcl726 driver has an "interrupt" subdevice that supports Comedi
asynchronous commands, placing a value in the Comedi buffer for each
interrupt. The subdevice uses Comedi's 16-bit sample format but the
interrupt handler is calling `comedi_buf_write_samples()` with the
address of a 32-bit integer `&s->state`. On bigendian machines, this
will copy 2 bytes from the wrong end of the 32-bit integer. This isn't
really a problem since `s->state` will always be 0 for this subdevice,
but clean it up by using a 16-bit variable initialized to 0 to pass the
value.
Ian Abbott [Tue, 23 Feb 2021 14:30:54 +0000 (14:30 +0000)]
staging: comedi: ni_65xx: Use 16-bit 0 for interrupt data
The ni_65xx driver has an "interrupt" subdevice that supports Comedi
asynchronous commands, placing a value in the Comedi buffer for each
interrupt. The subdevice uses Comedi's 16-bit sample format but the
interrupt handler is calling `comedi_buf_write_samples()` with the
address of a 32-bit integer `&s->state`. On bigendian machines, this
will copy 2 bytes from the wrong end of the 32-bit integer. This isn't
really a problem since `s->state` will always be 0 for this subdevice,
but clean it up by using a 16-bit variable initialized to 0 to pass the
value.
Ian Abbott [Tue, 23 Feb 2021 14:30:53 +0000 (14:30 +0000)]
staging: comedi: ni_6527: Use 16-bit 0 for interrupt data
The ni_6527 driver has an "interrupt" subdevice that supports Comedi
asynchronous commands, placing a value in the Comedi buffer for each
interrupt. The subdevice uses Comedi's 16-bit sample format but the
interrupt handler is calling `comedi_buf_write_samples()` with the
address of a 32-bit integer `&s->state`. On bigendian machines, this
will copy 2 bytes from the wrong end of the 32-bit integer. This isn't
really a problem since `s->state` will always be 0 for this subdevice,
but clean it up by using a 16-bit variable initialized to 0 to pass the
value.
Ian Abbott [Tue, 23 Feb 2021 14:30:52 +0000 (14:30 +0000)]
staging: comedi: comedi_parport: Use 16-bit 0 for interrupt data
The comedi_parport driver has an "interrupt" subdevice that supports
Comedi asynchronous commands, placing a value in the Comedi buffer for
each interrupt. The subdevice uses Comedi's 16-bit sample format but
the interrupt handler is calling `comedi_buf_write_samples()` with the
address of a 32-bit integer `&s->state`. On bigendian machines, this
will copy 2 bytes from the wrong end of the 32-bit integer. This isn't
really a problem since `s->state` will always be 0 for this subdevice,
but clean it up by using a 16-bit variable initialized to 0 to pass the
value.
Ian Abbott [Tue, 23 Feb 2021 14:30:51 +0000 (14:30 +0000)]
staging: comedi: amplc_pc236_common: Use 16-bit 0 for interrupt data
The Amplicon PC36AT/PCI236 common driver has an "interrupt" subdevice
that supports Comedi asynchronous commands, placing a value in the
Comedi buffer for each interrupt. The subdevice uses Comedi's 16-bit
sample format but the interrupt handler is calling
`comedi_buf_write_samples()` with the address of a 32-bit integer
`&s->state`. On bigendian machines, this will copy 2 bytes from the
wrong end of the 32-bit integer. This isn't really a problem since
`s->state` will always be 0 for this subdevice, but clean it up by using
a 16-bit variable initialized to 0 to pass the value.
Ian Abbott [Tue, 23 Feb 2021 14:30:50 +0000 (14:30 +0000)]
staging: comedi: pcl818: Fix endian problem for AI command data
The analog input subdevice supports Comedi asynchronous commands that
use Comedi's 16-bit sample format. However, the call to
`comedi_buf_write_samples()` is passing the address of a 32-bit integer
parameter. On bigendian machines, this will copy 2 bytes from the wrong
end of the 32-bit value. Fix it by changing the type of the parameter
holding the sample value to `unsigned short`.
[Note: the bug was introduced in commit edf4537bcbf5 ("staging: comedi:
pcl818: use comedi_buf_write_samples()") but the patch applies better to
commit d615416de615 ("staging: comedi: pcl818: introduce
pcl818_ai_write_sample()").]
Ian Abbott [Tue, 23 Feb 2021 14:30:49 +0000 (14:30 +0000)]
staging: comedi: pcl711: Fix endian problem for AI command data
The analog input subdevice supports Comedi asynchronous commands that
use Comedi's 16-bit sample format. However, the call to
`comedi_buf_write_samples()` is passing the address of a 32-bit integer
variable. On bigendian machines, this will copy 2 bytes from the wrong
end of the 32-bit value. Fix it by changing the type of the variable
holding the sample value to `unsigned short`.
Ian Abbott [Tue, 23 Feb 2021 14:30:48 +0000 (14:30 +0000)]
staging: comedi: me4000: Fix endian problem for AI command data
The analog input subdevice supports Comedi asynchronous commands that
use Comedi's 16-bit sample format. However, the calls to
`comedi_buf_write_samples()` are passing the address of a 32-bit integer
variable. On bigendian machines, this will copy 2 bytes from the wrong
end of the 32-bit value. Fix it by changing the type of the variable
holding the sample value to `unsigned short`.
Ian Abbott [Tue, 23 Feb 2021 14:30:47 +0000 (14:30 +0000)]
staging: comedi: dmm32at: Fix endian problem for AI command data
The analog input subdevice supports Comedi asynchronous commands that
use Comedi's 16-bit sample format. However, the call to
`comedi_buf_write_samples()` is passing the address of a 32-bit integer
variable. On bigendian machines, this will copy 2 bytes from the wrong
end of the 32-bit value. Fix it by changing the type of the variable
holding the sample value to `unsigned short`.
[Note: the bug was introduced in commit 1700529b24cc ("staging: comedi:
dmm32at: use comedi_buf_write_samples()") but the patch applies better
to the later (but in the same kernel release) commit 0c0eadadcbe6e
("staging: comedi: dmm32at: introduce dmm32_ai_get_sample()").]
Ian Abbott [Tue, 23 Feb 2021 14:30:46 +0000 (14:30 +0000)]
staging: comedi: das800: Fix endian problem for AI command data
The analog input subdevice supports Comedi asynchronous commands that
use Comedi's 16-bit sample format. However, the call to
`comedi_buf_write_samples()` is passing the address of a 32-bit integer
variable. On bigendian machines, this will copy 2 bytes from the wrong
end of the 32-bit value. Fix it by changing the type of the variable
holding the sample value to `unsigned short`.
Ian Abbott [Tue, 23 Feb 2021 14:30:45 +0000 (14:30 +0000)]
staging: comedi: das6402: Fix endian problem for AI command data
The analog input subdevice supports Comedi asynchronous commands that
use Comedi's 16-bit sample format. However, the call to
`comedi_buf_write_samples()` is passing the address of a 32-bit integer
variable. On bigendian machines, this will copy 2 bytes from the wrong
end of the 32-bit value. Fix it by changing the type of the variable
holding the sample value to `unsigned short`.
Ian Abbott [Tue, 23 Feb 2021 14:30:44 +0000 (14:30 +0000)]
staging: comedi: adv_pci1710: Fix endian problem for AI command data
The analog input subdevice supports Comedi asynchronous commands that
use Comedi's 16-bit sample format. However, the calls to
`comedi_buf_write_samples()` are passing the address of a 32-bit integer
variable. On bigendian machines, this will copy 2 bytes from the wrong
end of the 32-bit value. Fix it by changing the type of the variables
holding the sample value to `unsigned short`. The type of the `val`
parameter of `pci1710_ai_read_sample()` is changed to `unsigned short *`
accordingly. The type of the `val` variable in `pci1710_ai_insn_read()`
is also changed to `unsigned short` since its address is passed to
`pci1710_ai_read_sample()`.
Ian Abbott [Tue, 23 Feb 2021 14:30:43 +0000 (14:30 +0000)]
staging: comedi: addi_apci_1500: Fix endian problem for command sample
The digital input subdevice supports Comedi asynchronous commands that
read interrupt status information. This uses 16-bit Comedi samples (of
which only the bottom 8 bits contain status information). However, the
interrupt handler is calling `comedi_buf_write_samples()` with the
address of a 32-bit variable `unsigned int status`. On a bigendian
machine, this will copy 2 bytes from the wrong end of the variable. Fix
it by changing the type of the variable to `unsigned short`.
Ian Abbott [Tue, 23 Feb 2021 14:30:42 +0000 (14:30 +0000)]
staging: comedi: addi_apci_1032: Fix endian problem for COS sample
The Change-Of-State (COS) subdevice supports Comedi asynchronous
commands to read 16-bit change-of-state values. However, the interrupt
handler is calling `comedi_buf_write_samples()` with the address of a
32-bit integer `&s->state`. On bigendian architectures, it will copy 2
bytes from the wrong end of the 32-bit integer. Fix it by transferring
the value via a 16-bit integer.
Lee Gibson [Mon, 1 Mar 2021 13:26:48 +0000 (13:26 +0000)]
staging: rtl8712: Fix possible buffer overflow in r8712_sitesurvey_cmd
Function r8712_sitesurvey_cmd calls memcpy without checking the length.
A user could control that length and trigger a buffer overflow.
Fix by checking the length is within the maximum allowed size.
Lee Gibson [Fri, 26 Feb 2021 14:51:57 +0000 (14:51 +0000)]
staging: rtl8192e: Fix possible buffer overflow in _rtl92e_wx_set_scan
Function _rtl92e_wx_set_scan calls memcpy without checking the length.
A user could control that length and trigger a buffer overflow.
Fix by checking the length is within the maximum allowed size.
Dan Carpenter [Wed, 24 Feb 2021 08:45:59 +0000 (11:45 +0300)]
staging: rtl8712: unterminated string leads to read overflow
The memdup_user() function does not necessarily return a NUL terminated
string so this can lead to a read overflow. Switch from memdup_user()
to strndup_user() to fix this bug.
Julian Braha [Mon, 22 Feb 2021 18:06:07 +0000 (13:06 -0500)]
staging: rtl8192e: fix kconfig dependency on CRYPTO
When RTLLIB_CRYPTO_TKIP is enabled and CRYPTO is disabled,
Kbuild gives the following warning:
WARNING: unmet direct dependencies detected for CRYPTO_MICHAEL_MIC
Depends on [n]: CRYPTO [=n]
Selected by [m]:
- RTLLIB_CRYPTO_TKIP [=m] && STAGING [=y] && RTLLIB [=m]
WARNING: unmet direct dependencies detected for CRYPTO_LIB_ARC4
Depends on [n]: CRYPTO [=n]
Selected by [m]:
- RTLLIB_CRYPTO_TKIP [=m] && STAGING [=y] && RTLLIB [=m]
- RTLLIB_CRYPTO_WEP [=m] && STAGING [=y] && RTLLIB [=m]
This is because RTLLIB_CRYPTO_TKIP selects CRYPTO_MICHAEL_MIC and
CRYPTO_LIB_ARC4, without depending on or selecting CRYPTO,
despite those config options being subordinate to CRYPTO.
Shuo Liu [Sun, 21 Feb 2021 13:43:38 +0000 (21:43 +0800)]
cpu/hotplug: Fix build error of using {add,remove}_cpu() with !CONFIG_SMP
279dcf693ac7 ("virt: acrn: Introduce an interface for Service VM to
control vCPU") introduced {add,remove}_cpu() usage and it hit below
error with !CONFIG_SMP:
../drivers/virt/acrn/hsm.c: In function ‘remove_cpu_store’:
../drivers/virt/acrn/hsm.c:389:3: error: implicit declaration of function ‘remove_cpu’; [-Werror=implicit-function-declaration]
remove_cpu(cpu);
../drivers/virt/acrn/hsm.c:402:2: error: implicit declaration of function ‘add_cpu’; [-Werror=implicit-function-declaration]
add_cpu(cpu);
Add add_cpu() function prototypes with !CONFIG_SMP and remove_cpu() with
!CONFIG_HOTPLUG_CPU for such usage.
farah kassabri [Sun, 28 Feb 2021 09:06:14 +0000 (11:06 +0200)]
habanalabs: fix debugfs address translation
when user uses virtual addresses to access dram through debugfs,
driver translate this address to physical and use it
for the access through the pcie bar.
in case dram page size is different than the dmmu
page size, we need to have special treatment
for adding the page offset to the actual address, which
is to use the dram page size mask to fetch the page offset
from the virtual address, instead of the dmmu last hop shift.
Tomer Tayar [Mon, 1 Feb 2021 17:44:34 +0000 (19:44 +0200)]
habanalabs: Disable file operations after device is removed
A device can be removed from the PCI subsystem while a process holds the
file descriptor opened.
In such a case, the driver attempts to kill the process, but as it is
still possible that the process will be alive after this step, the
device removal will complete, and we will end up with a process object
that points to a device object which was already released.
To prevent the usage of this released device object, disable the
following file operations for this process object, and avoid the cleanup
steps when the file descriptor is eventually closed.
The latter is just a best effort, as memory leak will occur.
Tomer Tayar [Fri, 19 Feb 2021 12:05:33 +0000 (14:05 +0200)]
habanalabs: Call put_pid() when releasing control device
The refcount of the "hl_fpriv" structure is not used for the control
device, and thus hl_hpriv_put() is not called when releasing this
device.
This results with no call to put_pid(), so add it explicitly in
hl_device_release_ctrl().
drivers: habanalabs: remove unused dentry pointer for debugfs files
The dentry for the created debugfs file was being saved, but never used
anywhere. As the pointer isn't needed for anything, and the debugfs
files are being properly removed by removing the parent directory,
remove the saved pointer as well, saving a tiny bit of memory and logic.
1) Fix transmissions in dynamic SMPS mode in ath9k, from Felix Fietkau.
2) TX skb error handling fix in mt76 driver, also from Felix.
3) Fix BPF_FETCH atomic in x86 JIT, from Brendan Jackman.
4) Avoid double free of percpu pointers when freeing a cloned bpf prog.
From Cong Wang.
5) Use correct printf format for dma_addr_t in ath11k, from Geert
Uytterhoeven.
6) Fix resolve_btfids build with older toolchains, from Kun-Chuan
Hsieh.
7) Don't report truncated frames to mac80211 in mt76 driver, from
Lorenzop Bianconi.
8) Fix watcdog timeout on suspend/resume of stmmac, from Joakim Zhang.
9) mscc ocelot needs NET_DEVLINK selct in Kconfig, from Arnd Bergmann.
10) Fix sign comparison bug in TCP_ZEROCOPY_RECEIVE getsockopt(), from
Arjun Roy.
11) Ignore routes with deleted nexthop object in mlxsw, from Ido
Schimmel.
12) Need to undo tcp early demux lookup sometimes in nf_nat, from
Florian Westphal.
13) Fix gro aggregation for udp encaps with zero csum, from Daniel
Borkmann.
14) Make sure to always use imp*_ndo_send when necessaey, from Jason A.
Donenfeld.
15) Fix TRSCER masks in sh_eth driver from Sergey Shtylyov.
16) prevent overly huge skb allocationsd in qrtr, from Pavel Skripkin.
17) Prevent rx ring copnsumer index loss of sync in enetc, from Vladimir
Oltean.
18) Make sure textsearch copntrol block is large enough, from Wilem de
Bruijn.
19) Revert MAC changes to r8152 leading to instability, from Hates Wang.
20) Advance iov in 9p even for empty reads, from Jissheng Zhang.
21) Double hook unregister in nftables, from PabloNeira Ayuso.
22) Fix memleak in ixgbe, fropm Dinghao Liu.
23) Avoid dups in pkt scheduler class dumps, from Maximilian Heyne.
24) Various mptcp fixes from Florian Westphal, Paolo Abeni, and Geliang
Tang.
25) Fix DOI refcount bugs in cipso, from Paul Moore.
26) One too many irqsave in ibmvnic, from Junlin Yang.
27) Fix infinite loop with MPLS gso segmenting via virtio_net, from
Balazs Nemeth.
* git://git.kernel.org:/pub/scm/linux/kernel/git/netdev/net: (164 commits)
s390/qeth: fix notification for pending buffers during teardown
s390/qeth: schedule TX NAPI on QAOB completion
s390/qeth: improve completion of pending TX buffers
s390/qeth: fix memory leak after failed TX Buffer allocation
net: avoid infinite loop in mpls_gso_segment when mpls_hlen == 0
net: check if protocol extracted by virtio_net_hdr_set_proto is correct
net: dsa: xrs700x: check if partner is same as port in hsr join
net: lapbether: Remove netif_start_queue / netif_stop_queue
atm: idt77252: fix null-ptr-dereference
atm: uPD98402: fix incorrect allocation
atm: fix a typo in the struct description
net: qrtr: fix error return code of qrtr_sendmsg()
mptcp: fix length of ADD_ADDR with port sub-option
net: bonding: fix error return code of bond_neigh_init()
net: enetc: allow hardware timestamping on TX queues with tc-etf enabled
net: enetc: set MAC RX FIFO to recommended value
net: davicom: Use platform_get_irq_optional()
net: davicom: Fix regulator not turned off on driver removal
net: davicom: Fix regulator not turned off on failed probe
net: dsa: fix switchdev objects on bridge master mistakenly being applied on ports
...
After my patch there is CONFIG_ATA defined twice.
Remove the duplicate one.
Same problem for CONFIG_HAPPYMEAL, except I added as builtin for boot
test with NFS.
Reported-by: Stephen Rothwell <[email protected]> Fixes: a57cdeb369ef ("sparc: sparc64_defconfig: add necessary configs for qemu") Signed-off-by: Corentin Labbe <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Rob Gardner [Mon, 1 Mar 2021 05:48:16 +0000 (22:48 -0700)]
sparc64: Fix opcode filtering in handling of no fault loads
is_no_fault_exception() has two bugs which were discovered via random
opcode testing with stress-ng. Both are caused by improper filtering
of opcodes.
The first bug can be triggered by a floating point store with a no-fault
ASI, for instance "sta %f0, [%g0] #ASI_PNF", opcode C1A01040.
The code first tests op3[5] (0x1000000), which denotes a floating
point instruction, and then tests op3[2] (0x200000), which denotes a
store instruction. But these bits are not mutually exclusive, and the
above mentioned opcode has both bits set. The intent is to filter out
stores, so the test for stores must be done first in order to have
any effect.
The second bug can be triggered by a floating point load with one of
the invalid ASI values 0x8e or 0x8f, which pass this check in
is_no_fault_exception():
if ((asi & 0xf2) == ASI_PNF)
An example instruction is "ldqa [%l7 + %o7] #ASI 0x8f, %f38",
opcode CF95D1EF. Asi values greater than 0x8b (ASI_SNFL) are fatal
in handle_ldf_stq(), and is_no_fault_exception() must not allow these
invalid asi values to make it that far.
In both of these cases, handle_ldf_stq() reacts by calling
sun4v_data_access_exception() or spitfire_data_access_exception(),
which call is_no_fault_exception() and results in an infinite
recursion.
powerpc: Fix missing declaration of [en/dis]able_kernel_vsx()
Add stub instances of enable_kernel_vsx() and disable_kernel_vsx()
when CONFIG_VSX is not set, to avoid following build failure.
CC [M] drivers/gpu/drm/amd/amdgpu/../display/dc/calcs/dcn_calcs.o
In file included from ./drivers/gpu/drm/amd/amdgpu/../display/dc/dm_services_types.h:29,
from ./drivers/gpu/drm/amd/amdgpu/../display/dc/dm_services.h:37,
from drivers/gpu/drm/amd/amdgpu/../display/dc/calcs/dcn_calcs.c:27:
drivers/gpu/drm/amd/amdgpu/../display/dc/calcs/dcn_calcs.c: In function 'dcn_bw_apply_registry_override':
./drivers/gpu/drm/amd/amdgpu/../display/dc/os_types.h:64:3: error: implicit declaration of function 'enable_kernel_vsx'; did you mean 'enable_kernel_fp'? [-Werror=implicit-function-declaration]
64 | enable_kernel_vsx(); \
| ^~~~~~~~~~~~~~~~~
drivers/gpu/drm/amd/amdgpu/../display/dc/calcs/dcn_calcs.c:640:2: note: in expansion of macro 'DC_FP_START'
640 | DC_FP_START();
| ^~~~~~~~~~~
./drivers/gpu/drm/amd/amdgpu/../display/dc/os_types.h:75:3: error: implicit declaration of function 'disable_kernel_vsx'; did you mean 'disable_kernel_fp'? [-Werror=implicit-function-declaration]
75 | disable_kernel_vsx(); \
| ^~~~~~~~~~~~~~~~~~
drivers/gpu/drm/amd/amdgpu/../display/dc/calcs/dcn_calcs.c:676:2: note: in expansion of macro 'DC_FP_END'
676 | DC_FP_END();
| ^~~~~~~~~
cc1: some warnings being treated as errors
make[5]: *** [drivers/gpu/drm/amd/amdgpu/../display/dc/calcs/dcn_calcs.o] Error 1
This works because the caller is checking if VSX is available using
cpu_has_feature():
When CONFIG_VSX is not selected, cpu_has_feature(CPU_FTR_VSX_COMP)
constant folds to 'false' so the call to enable_kernel_vsx() is
discarded and the build succeeds.
David S. Miller [Wed, 10 Mar 2021 00:14:54 +0000 (16:14 -0800)]
Merge branch 's390-qeth-fixes'
Julian Wiedmann says:
====================
s390/qeth: fixes 2021-03-09
please apply the following patch series to netdev's net tree.
This brings one fix for a memleak in an error path of the setup code.
Also several fixes for dealing with pending TX buffers - two for old
bugs in their completion handling, and one recent regression in a
teardown path.
====================
Julian Wiedmann [Tue, 9 Mar 2021 16:52:21 +0000 (17:52 +0100)]
s390/qeth: fix notification for pending buffers during teardown
The cited commit reworked the state machine for pending TX buffers.
In qeth_iqd_tx_complete() it turned PENDING into a transient state, and
uses NEED_QAOB for buffers that get parked while waiting for their QAOB
completion.
But it missed to adjust the check in qeth_tx_complete_buf(). So if
qeth_tx_complete_pending_bufs() is called during teardown to drain
the parked TX buffers, we no longer raise a notification for af_iucv.
Instead of updating the checked state, just move this code into
qeth_tx_complete_pending_bufs() itself. This also gets rid of the
special-case in the common TX completion path.
Fixes: 8908f36d20d8 ("s390/qeth: fix af_iucv notification race") Signed-off-by: Julian Wiedmann <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Julian Wiedmann [Tue, 9 Mar 2021 16:52:20 +0000 (17:52 +0100)]
s390/qeth: schedule TX NAPI on QAOB completion
When a QAOB notifies us that a pending TX buffer has been delivered, the
actual TX completion processing by qeth_tx_complete_pending_bufs()
is done within the context of a TX NAPI instance. We shouldn't rely on
this instance being scheduled by some other TX event, but just do it
ourselves.
qeth_qdio_handle_aob() is called from qeth_poll(), ie. our main NAPI
instance. To avoid touching the TX queue's NAPI instance
before/after it is (un-)registered, reorder the code in qeth_open()
and qeth_stop() accordingly.
Fixes: 0da9581ddb0f ("qeth: exploit asynchronous delivery of storage blocks") Signed-off-by: Julian Wiedmann <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Julian Wiedmann [Tue, 9 Mar 2021 16:52:19 +0000 (17:52 +0100)]
s390/qeth: improve completion of pending TX buffers
The current design attaches a pending TX buffer to a custom
single-linked list, which is anchored at the buffer's slot on the
TX ring. The buffer is then checked for final completion whenever
this slot is processed during a subsequent TX NAPI poll cycle.
But if there's insufficient traffic on the ring, we might never make
enough progress to get back to this ring slot and discover the pending
buffer's final TX completion. In particular if this missing TX
completion blocks the application from sending further traffic.
So convert the custom single-linked list code to a per-queue list_head,
and scan this list on every TX NAPI cycle.
Fixes: 0da9581ddb0f ("qeth: exploit asynchronous delivery of storage blocks") Signed-off-by: Julian Wiedmann <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Julian Wiedmann [Tue, 9 Mar 2021 16:52:18 +0000 (17:52 +0100)]
s390/qeth: fix memory leak after failed TX Buffer allocation
When qeth_alloc_qdio_queues() fails to allocate one of the buffers that
back an Output Queue, the 'out_freeoutqbufs' path will free all
previously allocated buffers for this queue. But it misses to free the
half-finished queue struct itself.
Move the buffer allocation into qeth_alloc_output_queue(), and deal with
such errors internally.
Fixes: 0da9581ddb0f ("qeth: exploit asynchronous delivery of storage blocks") Signed-off-by: Julian Wiedmann <[email protected]> Reviewed-by: Alexandra Winter <[email protected]> Signed-off-by: David S. Miller <[email protected]>
David S. Miller [Wed, 10 Mar 2021 00:12:20 +0000 (16:12 -0800)]
Merge branch 'virtio_net-infinite-loop'
Balazs Nemeth says:
====================
net: prevent infinite loop caused by incorrect proto from virtio_net_hdr_set_proto
These patches prevent an infinite loop for gso packets with a protocol
from virtio net hdr that doesn't match the protocol in the packet.
Note that packets coming from a device without
header_ops->parse_protocol being implemented will not be caught by
the check in virtio_net_hdr_to_skb, but the infinite loop will still
be prevented by the check in the gso layer.
Changes from v2 to v3:
- Remove unused *eth.
- Use MPLS_HLEN to also check if the MPLS header length is a multiple
of four.
====================
Balazs Nemeth [Tue, 9 Mar 2021 11:31:01 +0000 (12:31 +0100)]
net: avoid infinite loop in mpls_gso_segment when mpls_hlen == 0
A packet with skb_inner_network_header(skb) == skb_network_header(skb)
and ETH_P_MPLS_UC will prevent mpls_gso_segment from pulling any headers
from the packet. Subsequently, the call to skb_mac_gso_segment will
again call mpls_gso_segment with the same packet leading to an infinite
loop. In addition, ensure that the header length is a multiple of four,
which should hold irrespective of the number of stacked labels.
Balazs Nemeth [Tue, 9 Mar 2021 11:31:00 +0000 (12:31 +0100)]
net: check if protocol extracted by virtio_net_hdr_set_proto is correct
For gso packets, virtio_net_hdr_set_proto sets the protocol (if it isn't
set) based on the type in the virtio net hdr, but the skb could contain
anything since it could come from packet_snd through a raw socket. If
there is a mismatch between what virtio_net_hdr_set_proto sets and
the actual protocol, then the skb could be handled incorrectly later
on.
An example where this poses an issue is with the subsequent call to
skb_flow_dissect_flow_keys_basic which relies on skb->protocol being set
correctly. A specially crafted packet could fool
skb_flow_dissect_flow_keys_basic preventing EINVAL to be returned.
Avoid blindly trusting the information provided by the virtio net header
by checking that the protocol in the packet actually matches the
protocol set by virtio_net_hdr_set_proto. Note that since the protocol
is only checked if skb->dev implements header_ops->parse_protocol,
packets from devices without the implementation are not checked at this
stage.
Fixes: 9274124f023b ("net: stricter validation of untrusted gso packets") Signed-off-by: Balazs Nemeth <[email protected]> Acked-by: Willem de Bruijn <[email protected]> Signed-off-by: David S. Miller <[email protected]>
net: dsa: xrs700x: check if partner is same as port in hsr join
Don't assign dp to partner if it's the same port that xrs700x_hsr_join
was called with. The partner port is supposed to be the other port in
the HSR/PRP redundant pair not the same port. This fixes an issue
observed in testing where forwarding between redundant HSR ports on this
switch didn't work depending on the order the ports were added to the
hsr device.
Fixes: bd62e6f5e6a9 ("net: dsa: xrs700x: add HSR offloading support") Signed-off-by: George McCollister <[email protected]> Reviewed-by: Vladimir Oltean <[email protected]> Signed-off-by: David S. Miller <[email protected]>
powerpc/64s: Use symbolic macros for function entry encoding
In ppc_function_entry() we look for a specific set of instructions by
masking the instructions and comparing with a known value. Currently
those known values are just literal hex values, and we recently
discovered one of them was wrong.
Instead construct the values using the existing constants we have for
defining various fields of instructions.
Wei Yongjun [Mon, 8 Mar 2021 12:35:01 +0000 (12:35 +0000)]
umem: fix error return code in mm_pci_probe()
Fix to return negative error code -ENOMEM from the blk_alloc_queue()
and dma_alloc_coherent() error handling cases instead of 0, as done
elsewhere in this function.
Linus Torvalds [Tue, 9 Mar 2021 20:02:18 +0000 (12:02 -0800)]
Merge tag 'gpio-fixes-for-v5.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fixes from Bartosz Golaszewski:
"A bunch of fixes for the GPIO subsystem. We have two regressions in
the core code spotted right after the merge window, a series of fixes
for ACPI GPIO and a subsequent fix for a related regression in
gpio-pca953x + a minor tweak in .gitignore and a rework of handling of
the gpio-line-names to remedy a regression in stm32mp151.
Summary:
- fix two regressions in core GPIO subsystem code: one NULL-pointer
dereference and one list corruption
- read GPIO line names from fwnode instead of using the generic
device properties to fix a regression on stm32mp151
- fixes to ACPI GPIO and gpio-pca953x to handle a regression in IRQ
handling on Intel Galileo
- update .gitignore in GPIO selftests"
* tag 'gpio-fixes-for-v5.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpiolib: Read "gpio-line-names" from a firmware node
gpio: pca953x: Set IRQ type when handle Intel Galileo Gen 2
gpiolib: acpi: Allow to find GpioInt() resource by name and index
gpiolib: acpi: Add ACPI_GPIO_QUIRK_ABSOLUTE_NUMBER quirk
gpiolib: acpi: Add missing IRQF_ONESHOT
gpio: fix gpio-device list corruption
gpio: fix NULL-deref-on-deregistration regression
selftests: gpio: update .gitignore
Linus Torvalds [Tue, 9 Mar 2021 19:56:41 +0000 (11:56 -0800)]
Merge tag 'mips-fixes_5.12_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Thomas Bogendoerfer:
- fixes for boot breakage because of misaligned FDTs
- fix for overwritten exception handlers
- enable MIPS optimized crypto for all MIPS CPUs to improve wireguard
performance
* tag 'mips-fixes_5.12_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: kernel: Reserve exception base early to prevent corruption
MIPS: vmlinux.lds.S: align raw appended dtb to 8 bytes
crypto: mips/poly1305 - enable for all MIPS processors
MIPS: boot/compressed: Copy DTB to aligned address
kbuild: Fix ld-version.sh script if LLD was built with LLD_VENDOR
If LLD was built with -DLLD_VENDOR="xyz", ld.lld --version output
will prefix LLD_VENDOR. Since LLD_VENDOR can contain spaces, the
LLD identifier isn't guaranteed to be $2 either.
Adjust the version checker to handle such versions of lld.
Jiri Slaby [Wed, 3 Mar 2021 10:43:14 +0000 (11:43 +0100)]
kbuild: dummy-tools: fix inverted tests for gcc
There is a test in Kconfig which takes inverted value of a compiler
check:
* config CC_HAS_INT128
def_bool !$(cc-option,$(m64-flag) -D__SIZEOF_INT128__=0)
This results in CC_HAS_INT128 not being in super-config generated by
dummy-tools. So take this into account in the gcc script.
Masahiro Yamada [Sun, 28 Feb 2021 06:10:25 +0000 (15:10 +0900)]
kbuild: add image_name to no-sync-config-targets
'make image_name' needs include/config/auto.conf to show the correct
output because KBUILD_IMAGE depends on CONFIG options, but should not
attempt to resync the configuration.
For the devices in this driver, the default qdisc is "noqueue",
because their "tx_queue_len" is 0.
In function "__dev_queue_xmit" in "net/core/dev.c", devices with the
"noqueue" qdisc are specially handled. Packets are transmitted without
being queued after a "dev->flags & IFF_UP" check. However, it's possible
that even if this check succeeds, "ops->ndo_stop" may still have already
been called. This is because in "__dev_close_many", "ops->ndo_stop" is
called before clearing the "IFF_UP" flag.
If we call "netif_stop_queue" in "ops->ndo_stop", then it's possible in
"__dev_queue_xmit", it sees the "IFF_UP" flag is present, and then it
checks "netif_xmit_stopped" and finds that the queue is already stopped.
In this case, it will complain that:
"Virtual device ... asks to queue packet!"
To prevent "__dev_queue_xmit" from generating this complaint, we should
not call "netif_stop_queue" in "ops->ndo_stop".
We also don't need to call "netif_start_queue" in "ops->ndo_open",
because after a netdev is allocated and registered, the
"__QUEUE_STATE_DRV_XOFF" flag is initially not set, so there is no need
to call "netif_start_queue" to clear it.
Ondrej Mosnacek [Fri, 15 Jan 2021 17:43:56 +0000 (18:43 +0100)]
NFSv4.2: fix return value of _nfs4_get_security_label()
An xattr 'get' handler is expected to return the length of the value on
success, yet _nfs4_get_security_label() (and consequently also
nfs4_xattr_get_nfs4_label(), which is used as an xattr handler) returns
just 0 on success.
Fix this by returning label.len instead, which contains the length of
the result.
Marc Zyngier [Wed, 3 Mar 2021 16:45:05 +0000 (16:45 +0000)]
KVM: arm64: Ensure I-cache isolation between vcpus of a same VM
It recently became apparent that the ARMv8 architecture has interesting
rules regarding attributes being used when fetching instructions
if the MMU is off at Stage-1.
In this situation, the CPU is allowed to fetch from the PoC and
allocate into the I-cache (unless the memory is mapped with
the XN attribute at Stage-2).
If we transpose this to vcpus sharing a single physical CPU,
it is possible for a vcpu running with its MMU off to influence
another vcpu running with its MMU on, as the latter is expected to
fetch from the PoU (and self-patching code doesn't flush below that
level).
In order to solve this, reuse the vcpu-private TLB invalidation
code to apply the same policy to the I-cache, nuking it every time
the vcpu runs on a physical CPU that ran another vcpu of the same
VM in the past.
This involve renaming __kvm_tlb_flush_local_vmid() to
__kvm_flush_cpu_context(), and inserting a local i-cache invalidation
there.
arm64: kasan: fix page_alloc tagging with DEBUG_VIRTUAL
When CONFIG_DEBUG_VIRTUAL is enabled, the default page_to_virt() macro
implementation from include/linux/mm.h is used. That definition doesn't
account for KASAN tags, which leads to no tags on page_alloc allocations.
Provide an arm64-specific definition for page_to_virt() when
CONFIG_DEBUG_VIRTUAL is enabled that takes care of KASAN tags.
Joerg Roedel [Wed, 3 Mar 2021 14:17:16 +0000 (15:17 +0100)]
x86/sev-es: Use __copy_from_user_inatomic()
The #VC handler must run in atomic context and cannot sleep. This is a
problem when it tries to fetch instruction bytes from user-space via
copy_from_user().
Introduce a insn_fetch_from_user_inatomic() helper which uses
__copy_from_user_inatomic() to safely copy the instruction bytes to
kernel memory in the #VC handler.
Joerg Roedel [Wed, 3 Mar 2021 14:17:13 +0000 (15:17 +0100)]
x86/sev-es: Check regs->sp is trusted before adjusting #VC IST stack
The code in the NMI handler to adjust the #VC handler IST stack is
needed in case an NMI hits when the #VC handler is still using its IST
stack.
But the check for this condition also needs to look if the regs->sp
value is trusted, meaning it was not set by user-space. Extend the check
to not use regs->sp when the NMI interrupted user-space code or the
SYSCALL gap.
MIPS: kernel: Reserve exception base early to prevent corruption
BMIPS is one of the few platforms that do change the exception base.
After commit 2dcb39645441 ("memblock: do not start bottom-up allocations
with kernel_end") we started seeing BMIPS boards fail to boot with the
built-in FDT being corrupted.
Before the cited commit, early allocations would be in the [kernel_end,
RAM_END] range, but after commit they would be within [RAM_START +
PAGE_SIZE, RAM_END].
The custom exception base handler that is installed by
bmips_ebase_setup() done for BMIPS5000 CPUs ends-up trampling on the
memory region allocated by unflatten_and_copy_device_tree() thus
corrupting the FDT used by the kernel.
To fix this, we need to perform an early reservation of the custom
exception space. Additional we reserve the first 4k (1k for R3k) for
either normal exception vector space (legacy CPUs) or special vectors
like cache exceptions.
Huge thanks to Serge for analysing and proposing a solution to this
issue.
The problem occurs when cqhci_request() get called after cqhci_disable() as
it leads to access of allocated memory that has already been freed. Let's
fix the problem by calling cqhci_disable() a bit later in the remove path.
Yann Gautier [Thu, 25 Feb 2021 14:54:54 +0000 (15:54 +0100)]
mmc: mmci: Add MMC_CAP_NEED_RSP_BUSY for the stm32 variants
An issue has been observed on STM32MP157C-EV1 board, with an erase command
with secure erase argument, ending up waiting for ~4 hours before timeout.
The requested busy timeout from the mmc core ends up with 14784000ms (~4
hours), but the supported host->max_busy_timeout is 86767ms, which leads to
that the core switch to use an R1 response in favor of the R1B and polls
for busy with the host->card_busy() ops. In this case the polling doesn't
work as expected, as we never detects that the card stops signaling busy,
which leads to the following message:
mmc1: Card stuck being busy! __mmc_poll_for_busy
The problem boils done to that the stm32 variants can't use R1 responses in
favor of R1B responses, as it leads to an internal state machine in the
controller to get stuck. To continue to process requests, it would need to
be reset.
To fix this problem, let's set MMC_CAP_NEED_RSP_BUSY for the stm32 variant,
which prevent the mmc core from switching to R1 responses. Additionally,
let's cap the cmd->busy_timeout to the host->max_busy_timeout, thus rely on
86767ms to be sufficient (~66 seconds was need for this test case).
Sami Tolvanen [Fri, 5 Mar 2021 20:21:24 +0000 (12:21 -0800)]
KVM: arm64: Don't use cbz/adr with external symbols
allmodconfig + CONFIG_LTO_CLANG_THIN=y fails to build due to following
linker errors:
ld.lld: error: irqbypass.c:(function __guest_enter: .text+0x21CC):
relocation R_AARCH64_CONDBR19 out of range: 2031220 is not in
[-1048576, 1048575]; references hyp_panic
>>> defined in vmlinux.o
ld.lld: error: irqbypass.c:(function __guest_enter: .text+0x21E0):
relocation R_AARCH64_ADR_PREL_LO21 out of range: 2031200 is not in
[-1048576, 1048575]; references hyp_panic
>>> defined in vmlinux.o
This is because with LTO, the compiler ends up placing hyp_panic()
more than 1MB away from __guest_enter(). Use an unconditional branch
and adr_l instead to fix the issue.
Niv Sardi [Mon, 1 Mar 2021 20:16:12 +0000 (17:16 -0300)]
USB: serial: ch341: add new Product ID
Add PID for CH340 that's found on cheap programmers.
The driver works flawlessly as soon as the new PID (0x9986) is added to it.
These look like ANU232MI but ship with a ch341 inside. They have no special
identifiers (mine only has the string "DB9D20130716" printed on the PCB and
nothing identifiable on the packaging. The merchant i bought it from
doesn't sell these anymore).
the lsusb -v output is:
Bus 001 Device 009: ID 9986:7523
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 255 Vendor Specific Class
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x9986
idProduct 0x7523
bcdDevice 2.54
iManufacturer 0
iProduct 0
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 0x0027
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 96mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 1
bInterfaceProtocol 2
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0020 1x 32 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0020 1x 32 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 1
projects / linux.git / log