Dave Airlie [Fri, 6 Sep 2024 01:25:38 +0000 (11:25 +1000)]
Merge tag 'drm-misc-fixes-2024-09-05' of https://gitlab.freedesktop.org/drm/misc/kernel into drm-fixes
A zpos normalization fix for komeda, a register bitmask fix for nouveau,
a memory leak fix for imagination, three fixes for the recent bridge
HDMI work, a potential DoS fix and a cache coherency for panthor, a
change of panel compatible and a deferred-io fix when used with
non-highmem memory.
Dave Airlie [Thu, 5 Sep 2024 23:45:52 +0000 (09:45 +1000)]
Merge tag 'drm-intel-fixes-2024-09-05' of https://gitlab.freedesktop.org/drm/i915/kernel into drm-fixes
- drm/i915: Do not attempt to load the GSC multiple times (Daniele Ceraolo Spurio)
- drm/i915: Fix readout degamma_lut mismatch on ilk/snb (Ville Syrjälä)
- drm/i915/fence: Mark debug_fence_init_onstack() with __maybe_unused (Andy Shevchenko)
- drm/i915/fence: Mark debug_fence_free() with __maybe_unused (Andy Shevchenko)
- drm/i915/display: Add mechanism to use sink model when applying quirk [display] (Jouni Högander)
- drm/i915/display: Increase Fast Wake Sync length as a quirk [display] (Jouni Högander)
drm/fbdev-dma: Only install deferred I/O if necessary
Deferred I/O requires struct page for framebuffer memory, which is
not guaranteed for all DMA ranges. We thus only install deferred I/O
if we have a framebuffer that requires it.
A reported bug affected the ipu-v3 and pl111 drivers, which have video
memory in either Normal or HighMem zones
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000010000000-0x000000003fffffff]
[ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff]
where deferred I/O only works correctly with HighMem. See the Closes
tags for bug reports.
v2:
- test if screen_buffer supports deferred I/O (Sima)
drm/panthor: flush FW AS caches in slow reset path
In the off-chance that waiting for the firmware to signal its booted status
timed out in the fast reset path, one must flush the cache lines for the
entire FW VM address space before reloading the regions, otherwise stale
values eventually lead to a scheduler job timeout.
As per the previous dt-binding commit, update the WL-355608-A8 panel
compatible to reflect the the integrating device vendor and name as the
panel OEM is unknown.
Ryan Walklin [Wed, 4 Sep 2024 01:23:21 +0000 (13:23 +1200)]
dt-bindings: display: panel: Rename WL-355608-A8 panel to rg35xx-*-panel
The WL-355608-A8 is a 3.5" 640x480@60Hz RGB LCD display from an unknown
OEM used in a number of handheld gaming devices made by Anbernic.
Previously committed using the OEM serial without a vendor prefix,
however following subsequent discussion the preference is to use the
integrating device vendor and name where the OEM is unknown.
There are 4 RG35XX series devices from Anbernic based on an Allwinner
H700 SoC using this panel, with the -Plus variant introduced first.
Therefore the -Plus is used as the fallback for the subsequent -H,
-2024, and -SP devices.
Alter the filename and compatible string to reflect the convention.
Rodrigo Vivi [Fri, 30 Aug 2024 18:35:07 +0000 (14:35 -0400)]
drm/xe/display: Avoid encoder_suspend at runtime suspend
Fix circular locking dependency on runtime suspend.
<4> [74.952215] ======================================================
<4> [74.952217] WARNING: possible circular locking dependency detected
<4> [74.952219] 6.10.0-rc7-xe #1 Not tainted
<4> [74.952221] ------------------------------------------------------
<4> [74.952223] kworker/7:1/82 is trying to acquire lock:
<4> [74.952226] ffff888120548488 (&dev->mode_config.mutex){+.+.}-{3:3}, at: drm_modeset_lock_all+0x40/0x1e0 [drm]
<4> [74.952260]
but task is already holding lock:
<4> [74.952262] ffffffffa0ae59c0 (xe_pm_runtime_lockdep_map){+.+.}-{0:0}, at: xe_pm_runtime_suspend+0x2f/0x340 [xe]
<4> [74.952322]
which lock already depends on the new lock.
The commit 'b1d90a86 ("drm/xe: Use the encoder suspend helper also used
by the i915 driver")' didn't do anything wrong. It actually fixed a
critical bug, because the encoder_suspend was never getting actually
called because it was returning if (has_display(xe)) instead of
if (!has_display(xe)). However, this ended up introducing the encoder
suspend calls in the runtime routines as well, causing the circular
locking dependency.
drm/xe/display: Match i915 driver suspend/resume sequences better
Suspend fbdev sooner, and disable user access before suspending to
prevent some races. I've noticed this when comparing xe suspend to
i915's.
Matches the following commits from i915: 24b412b1bfeb ("drm/i915: Disable intel HPD poll after DRM poll init/enable") 1ef28d86bea9 ("drm/i915: Suspend the framebuffer console earlier during system suspend") bd738d859e71 ("drm/i915: Prevent modesets during driver init/shutdown")
Thanks to Imre for pointing me to those commits.
Driver shutdown is currently missing, but I have some idea how to
implement it next.
Matt Roper [Thu, 29 Aug 2024 22:06:21 +0000 (15:06 -0700)]
drm/xe/pcode: Treat pcode as per-tile rather than per-GT
There's only one instance of the pcode per tile, and for GT-related
accesses both the primary and media GT share the same register
interface. Since Xe was using per-GT locking, the pcode mutex wasn't
actually protecting everything that it should since concurrent accesses
related to a tile's primary GT and media GT were possible.
drm/xe/gsc: Do not attempt to load the GSC multiple times
The GSC HW is only reset by driver FLR or D3cold entry. We don't support
the former at runtime, while the latter is only supported on DGFX, for
which we don't support GSC. Therefore, if GSC failed to load previously
there is no need to try again because the HW is stuck in the error state.
An assert has been added so that if we ever add DGFX support we'll know
we need to handle the D3 case.
v2: use "< 0" instead of "!= 0" in the FW state error check (Julia).
drm/bridge-connector: reset the HDMI connector state
On HDMI connectors which use drm_bridge_connector and DRM_BRIDGE_OP_HDMI
IGT chokes on the max_bpc property in several kms_properties tests due
to the drm_bridge_connector failing to reset HDMI-related
properties.
Call __drm_atomic_helper_connector_hdmi_reset() if the
drm_bridge_connector has bridge_hdmi.
It is impossible to call this function from HDMI bridges, none of the
bridge callbacks correspond to the drm_connector_funcs::reset().
drm/bridge-connector: move to DRM_DISPLAY_HELPER module
drm_bridge_connector is a "leaf" driver, belonging to the display
helper, rather than the "CRTC" drm_kms_helper module. Move the driver
to the drm/display and add necessary Kconfig selection clauses.
Kconfig symbols should not declare dependency on DRM_DISPLAY_HELPER.
Move all parts of DRM_DISPLAY_HELPER to an if DRM_DISPLAY_HELPER block.
It is not possible to make those symbols select DRM_DISPLAY_HELPER
because of the link issues when a part of the helper is selected to be
built-in, while other part is selected to be as module. In such a case
the modular part doesn't get built at all, leading to undefined symbols.
The only viable alternative is to split drm_display_helper.ko into
several small modules, each of them having their own dependencies.
drm/i915/display: Increase Fast Wake Sync length as a quirk
In commit "drm/i915/display: Increase number of fast wake precharge pulses"
we were increasing Fast Wake sync pulse length to fix problems observed on
Dell Precision 5490 laptop with AUO panel. Later we have observed this is
causing problems on other panels.
Fix these problems by increasing Fast Wake sync pulse length as a quirk
applied for Dell Precision 5490 with problematic panel.
drm/i915/display: Add mechanism to use sink model when applying quirk
Currently there is no way to apply quirk on device only if certain panel
model is installed. This patch implements such mechanism by adding new
quirk type intel_dpcd_quirk which contains also sink_oui and sink_device_id
fields and using also them to figure out if applying quirk is needed.
New intel_init_dpcd_quirks is added and called after drm_dp_read_desc with
proper sink device identity read from dpcdc.
v3:
- !mem_is_zero fixed to mem_is_zero
v2:
- instead of using struct intel_quirk add new struct intel_dpcd_quirk
Leo Li [Tue, 20 Aug 2024 18:34:15 +0000 (14:34 -0400)]
drm/amd/display: Lock DC and exit IPS when changing backlight
Backlight updates require aux and/or register access. Therefore, driver
needs to disallow IPS beforehand.
So, acquire the dc lock before calling into dc to update backlight - we
should be doing this regardless of IPS. Then, while the lock is held,
disallow IPS before calling into dc, then allow IPS afterwards (if it
was previously allowed).
Alex Deucher [Tue, 26 Mar 2024 15:28:29 +0000 (11:28 -0400)]
drm/amdgpu: always allocate cleared VRAM for GEM allocations
This adds allocation latency, but aligns better with user
expectations. The latency should improve with the drm buddy
clearing patches that Arun has been working on.
In addition this fixes the high CPU spikes seen when doing
wipe on release.
v2: always set AMDGPU_GEM_CREATE_VRAM_CLEARED (Christian)
Leo Li [Tue, 27 Aug 2024 15:29:53 +0000 (11:29 -0400)]
drm/amd/display: Determine IPS mode by ASIC and PMFW versions
[Why]
DCN IPS interoperates with other system idle power features, such as
Zstates.
On DCN35, there is a known issue where system Z8 + DCN IPS2 causes a
hard hang. We observe this on systems where the SBIOS allows Z8.
Though there is a SBIOS fix, there's no guarantee that users will get it
any time soon, or even install it. A workaround is needed to prevent
this from rearing its head in the wild.
[How]
For DCN35, check the pmfw version to determine whether the SBIOS has the
fix. If not, set IPS1+RCG as the deepest possible state in all cases
except for s0ix and display off (DPMS). Otherwise, enable all IPS
Ville Syrjälä [Wed, 10 Jul 2024 12:41:37 +0000 (15:41 +0300)]
drm/i915: Fix readout degamma_lut mismatch on ilk/snb
On ilk/snb the pipe may be configured to place the LUT before or
after the CSC depending on various factors, but as there is only
one LUT (no split mode like on IVB+) we only advertise a gamma_lut
and no degamma_lut in the uapi to avoid confusing userspace.
This can cause a problem during readout if the VBIOS/GOP enabled
the LUT in the pre CSC configuration. The current code blindly
assigns the results of the readout to the degamma_lut, which will
cause a failure during the next atomic_check() as we aren't expecting
anything to be in degamma_lut since it's not visible to userspace.
Fix the problem by assigning whatever LUT we read out from the
hardware into gamma_lut.
drm/i915: Do not attempt to load the GSC multiple times
If the GSC FW fails to load the GSC HW hangs permanently; the only ways
to recover it are FLR or D3cold entry, with the former only being
supported on driver unload and the latter only on DGFX, for which we
don't need to load the GSC. Therefore, if GSC fails to load there is no
need to try again because the HW is stuck in the error state and the
submission to load the FW would just hang the GSCCS.
Note that, due to wa_14015076503, on MTL the GuC escalates all GSCCS
hangs to full GT resets, which would trigger a new attempt to load the
GSC FW in the post-reset HW re-init; this issue is also fixed by not
attempting to load the GSC FW after an error.
Matt Coster [Mon, 2 Sep 2024 08:48:48 +0000 (09:48 +0100)]
drm/imagination: Free pvr_vm_gpuva after unlink
This caused a measurable memory leak. Although the individual
allocations are small, the leaks occurs in a high-usage codepath
(remapping or unmapping device memory) so they add up quickly.
Merge tag 'v6.11-rc5-smb-client-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull smb client fixes from Steve French:
- copy_file_range fix
- two read fixes including read past end of file rc fix and read retry
crediting fix
- falloc zero range fix
* tag 'v6.11-rc5-smb-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Fix FALLOC_FL_ZERO_RANGE to preflush buffered part of target region
cifs: Fix copy offload to flush destination region
netfs, cifs: Fix handling of short DIO read
cifs: Fix lack of credit renegotiation on read retry
Merge tag 'bcachefs-2024-08-21' of https://github.com/koverstreet/bcachefs
Push bcachefs fixes from Kent Overstreet:
"The data corruption in the buffered write path is troubling; inode
lock should not have been able to cause that...
- Fix a rare data corruption in the rebalance path, caught as a nonce
inconsistency on encrypted filesystems
- Revert lockless buffered write path
- Mark more errors as autofix"
* tag 'bcachefs-2024-08-21' of https://github.com/koverstreet/bcachefs:
bcachefs: Mark more errors as autofix
bcachefs: Revert lockless buffered IO path
bcachefs: Fix bch2_extents_match() false positive
bcachefs: Fix failure to return error in data_update_index_update()
Kent Overstreet [Thu, 22 Aug 2024 15:47:32 +0000 (11:47 -0400)]
bcachefs: Mark more errors as autofix
errors that are known to always be safe to fix should be autofix: this
should be most errors even at this point, but that will need some
thorough review.
note that errors are still logged in the superblock, so we'll still know
that they happened.
It seems that writes are being dropped, but only when issued by QEMU,
and possibly only in snapshot mode. It's undetermined if it's write
calls are being dropped or dirty folios.
Further testing, via minimizing the original patch to just the change
that skips the inode lock on non appends/truncates, reveals that it
really is just not taking the inode lock that causes the corruption: it
has nothing to do with the other logic changes for preserving write
atomicity in corner cases.
It's also kernel config dependent: it doesn't reproduce with the minimal
kernel config that ktest uses, but it does reproduce with nixos's distro
config. Bisection the kernel config initially pointer the finger at page
migration or compaction, but it appears that was erroneous; we haven't
yet determined what kernel config option actually triggers it.
Sadly it appears this will have to be reverted since we're getting too
close to release and my plate is full, but we'd _really_ like to fully
debug it.
My suspicion is that this patch is exposing a preexisting bug - the
inode lock actually covers very little in IO paths, and we have a
different lock (the pagecache add lock) that guards against races with
truncate here.
Fixes: 7e64c86cdc6c ("bcachefs: Buffered write path now can avoid the inode lock") Signed-off-by: Kent Overstreet <[email protected]>
Linus Torvalds [Sat, 31 Aug 2024 21:18:48 +0000 (09:18 +1200)]
Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull misc fixes from Guenter Roeck.
These are fixes for regressions that Guenther has been reporting, and
the maintainers haven't picked up and sent in. With rc6 fairly imminent,
I'm taking them directly from Guenter.
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
apparmor: fix policy_unpack_test on big endian systems
Revert "MIPS: csrc-r4k: Apply verification clocksource flags"
microblaze: don't treat zero reserved memory regions as error
Linus Torvalds [Sat, 31 Aug 2024 21:07:44 +0000 (09:07 +1200)]
Merge tag 'pwrseq-fixes-for-v6.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull power sequencing fix from Bartosz Golaszewski:
"A follow-up fix for the power sequencing subsystem. It turned out the
previous fix for this driver was incomplete and broke the WLAN support
on some platforms. This addresses the issue.
- set the direction of the wlan-enable GPIO to output after
requesting it as-is"
* tag 'pwrseq-fixes-for-v6.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
power: sequencing: qcom-wcn: set the wlan-enable GPIO to output
power: sequencing: qcom-wcn: set the wlan-enable GPIO to output
Commit a9aaf1ff88a8 ("power: sequencing: request the WLAN enable GPIO
as-is") broke WLAN on boards on which the wlan-enable GPIO enabling the
wifi module isn't in output mode by default. We need to set direction to
output while retaining the value that was already set to keep the ath
module on if it's already started.
Linus Torvalds [Sat, 31 Aug 2024 19:00:38 +0000 (07:00 +1200)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Minor fixes only.
The sd.c one ignores a sync cache request if format is in progress
which can happen if formatting a drive across suspend/resume"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: sd: Ignore command SYNCHRONIZE CACHE error if format in progress
scsi: aacraid: Fix double-free on probe failure
scsi: lpfc: Fix overflow build issue
Linus Torvalds [Sat, 31 Aug 2024 18:55:47 +0000 (06:55 +1200)]
Merge tag 'nfsd-6.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux
Pull nfsd fix from Chuck Lever:
- One more write delegation fix
* tag 'nfsd-6.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
nfsd: fix nfsd4_deleg_getattr_conflict in presence of third party lease
Linus Torvalds [Sat, 31 Aug 2024 18:48:37 +0000 (06:48 +1200)]
Merge tag 'xfs-6.11-fixes-4' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs fixes from Chandan Babu:
- Do not call out v1 inodes with non-zero di_nlink field as being
corrupt
- Change xfs_finobt_count_blocks() to count "free inode btree" blocks
rather than "inode btree" blocks
- Don't report the number of trimmed bytes via FITRIM because the
underlying storage isn't required to do anything and failed discard
IOs aren't reported to the caller anyway
- Fix incorrect setting of rm_owner field in an rmap query
- Report missing disk offset range in an fsmap query
- Obtain m_growlock when extending realtime section of the filesystem
- Reset rootdir extent size hint after extending realtime section of
the filesystem
* tag 'xfs-6.11-fixes-4' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: reset rootdir extent size hint after growfsrt
xfs: take m_growlock when running growfsrt
xfs: Fix missing interval for missing_owner in xfs fsmap
xfs: use XFS_BUF_DADDR_NULL for daddrs in getfsmap code
xfs: Fix the owner setting issue for rmap query in xfs fsmap
xfs: don't bother reporting blocks trimmed via FITRIM
xfs: xfs_finobt_count_blocks() walks the wrong btree
xfs: fix folio dirtying for XFILE_ALLOC callers
xfs: fix di_onlink checking for V1/V2 inodes
Linus Torvalds [Sat, 31 Aug 2024 18:42:13 +0000 (06:42 +1200)]
Merge tag 'arm-fixes-6.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"There is a fairly large number of bug fixes for Qualcomm platforms,
most of them addressing issues with the devicetree files for the newly
added Snapdragon X1 based laptops to make them more reliable.
The Qualcomm driver changes address a few build-time issues as well as
runtime problems in the tzmem and scm firmware, the USB Type-C driver,
and the cmd-db and pmic_glink soc drivers.
The NXP i.MX usually gets a bunch of devicetree fixes that is
proportional to the number of supported machines. This includes both
warning fixes and correctness for the 64-bit i.MX9, i.MX8 and
layerscape platforms, as well as a single fix for a 32-bit i.MX6 based
board.
The other changes are the usual minor changes, including an update to
the MAINTAINERS file, an omap3 dts file and a SoC driver for mpfs
(risc-v)"
* tag 'arm-fixes-6.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (50 commits)
firmware: microchip: fix incorrect error report of programming:timeout on success
soc: qcom: pd-mapper: Fix singleton refcount
firmware: qcom: tzmem: disable sdm670 platform
soc: qcom: pmic_glink: Actually communicate when remote goes down
usb: typec: ucsi: Move unregister out of atomic section
soc: qcom: pmic_glink: Fix race during initialization
firmware: qcom: qseecom: remove unused functions
firmware: qcom: tzmem: fix virtual-to-physical address conversion
firmware: qcom: scm: Mark get_wq_ctx() as atomic call
arm64: dts: qcom: x1e80100: Fix Adreno SMMU global interrupt
arm64: dts: qcom: disable GPU on x1e80100 by default
arm64: dts: imx8mm-phygate: fix typo pinctrcl-0
arm64: dts: imx95: correct L3Cache cache-sets
arm64: dts: imx95: correct a55 power-domains
arm64: dts: freescale: imx93-tqma9352-mba93xxla: fix typo
arm64: dts: freescale: imx93-tqma9352: fix CMA alloc-ranges
ARM: dts: imx6dl-yapp43: Increase LED current to match the yapp4 HW design
arm64: dts: imx93: update default value for snps,clk-csr
arm64: dts: freescale: tqma9352: Fix watchdog reset
arm64: dts: imx8mp-beacon-kit: Fix Stereo Audio on WM8962
...
Linus Torvalds [Sat, 31 Aug 2024 03:32:38 +0000 (15:32 +1200)]
Merge tag 'input-for-v6.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fix from Dmitry Torokhov:
- a fix for Cypress PS/2 touchpad for regression introduced in 6.11
merge window where a timeout condition is incorrectly reported for
all extended Cypress commands
* tag 'input-for-v6.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: cypress_ps2 - fix waiting for command response
Linus Torvalds [Sat, 31 Aug 2024 02:54:11 +0000 (14:54 +1200)]
Merge tag 'pci-v6.11-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci fixes from Bjorn Helgaas:
- Add Manivannan Sadhasivam as PCI native host bridge and endpoint
driver reviewer (Manivannan Sadhasivam)
- Disable MHI RAM data parity error interrupt for qcom SA8775P SoC to
work around hardware erratum that causes a constant stream of
interrupts (Manivannan Sadhasivam)
- Don't try to fall back to qcom Operating Performance Points (OPP)
support unless the platform actually supports OPP (Manivannan
Sadhasivam)
- Add [email protected] mailing list to MAINTAINERS for NXP
layerscape and imx6 PCI controller drivers (Frank Li)
* tag 'pci-v6.11-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
MAINTAINERS: PCI: Add NXP PCI controller mailing list [email protected]
PCI: qcom: Use OPP only if the platform supports it
PCI: qcom-ep: Disable MHI RAM data parity error interrupt for SA8775P SoC
MAINTAINERS: Add Manivannan Sadhasivam as Reviewer for PCI native host bridge and endpoint drivers
Linus Torvalds [Sat, 31 Aug 2024 01:51:27 +0000 (13:51 +1200)]
Merge tag 'io_uring-6.11-20240830' of git://git.kernel.dk/linux
Pull io_uring fixes from Jens Axboe:
- A fix for a regression that happened in 6.11 merge window, where the
copying of iovecs for compat mode applications got broken for certain
cases.
- Fix for a bug introduced in 6.10, where if using recv/send bundles
with classic provided buffers, the recv/send would fail to set the
right iovec count. This caused 0 byte send/recv results. Found via
code coverage testing and writing a test case to exercise it.
* tag 'io_uring-6.11-20240830' of git://git.kernel.dk/linux:
io_uring/kbuf: return correct iovec count from classic buffer peek
io_uring/rsrc: ensure compat iovecs are copied correctly
Linus Torvalds [Fri, 30 Aug 2024 18:33:59 +0000 (06:33 +1200)]
Merge tag 'lsm-pr-20240830' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/lsm
Pull lsm fix from Paul Moore:
"One small patch to correct a NFS permissions problem with SELinux and
Smack"
* tag 'lsm-pr-20240830' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/lsm:
selinux,smack: don't bypass permissions check in inode_setsecctx hook
Linus Torvalds [Fri, 30 Aug 2024 18:25:34 +0000 (06:25 +1200)]
Merge tag 'pm-6.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix three issues in the amd-pstate cpufreq driver.
Specifics:
- Remove checks for highest performance match on preferred cores when
updating preferred core ranking in amd-pstate (Mario Limonciello)
- Make amd-pstate call topology_logical_package_id() instead of
logical_die_id() to get a socked ID for a CPU (Gautham Shenoy)
- Fix uninitialized variable in amd_pstate_cpu_boost_update() (Dan
Carpenter)"
* tag 'pm-6.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq/amd-pstate-ut: Don't check for highest perf matching on prefcore
cpufreq/amd-pstate: Use topology_logical_package_id() instead of logical_die_id()
cpufreq: amd-pstate: Fix uninitialized variable in amd_pstate_cpu_boost_update()
Linus Torvalds [Fri, 30 Aug 2024 18:15:02 +0000 (06:15 +1200)]
Merge tag 'soundwire-6.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire
Pull soundwire fix from Vinod Koul:
- Single fix for non-continous port map programming
* tag 'soundwire-6.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire:
soundwire: stream: fix programming slave ports for non-continous port maps
Linus Torvalds [Fri, 30 Aug 2024 18:11:34 +0000 (06:11 +1200)]
Merge tag 'iommu-fixes-v6.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux
Pull iommu fixes from Joerg Roedel:
- Fix a device-stall problem in bad io-page-fault setups (faults
received from devices with no supporting domain attached).
- Context flush fix for Intel VT-d.
- Do not allow non-read+non-write mapping through iommufd as most
implementations can not handle that.
- Fix a possible infinite-loop issue in map_pages() path.
- Add Jean-Philippe as reviewer for SMMUv3 SVA support
* tag 'iommu-fixes-v6.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux:
MAINTAINERS: Add Jean-Philippe as SMMUv3 SVA reviewer
iommu: Do not return 0 from map_pages if it doesn't do anything
iommufd: Do not allow creating areas without READ or WRITE
iommu/vt-d: Fix incorrect domain ID in context flush helper
iommu: Handle iommu faults for a bad iopf setup
Jens Axboe [Fri, 30 Aug 2024 16:45:54 +0000 (10:45 -0600)]
io_uring/kbuf: return correct iovec count from classic buffer peek
io_provided_buffers_select() returns 0 to indicate success, but it should
be returning 1 to indicate that 1 vec was mapped. This causes peeking
to fail with classic provided buffers, and while that's not a use case
that anyone should use, it should still work correctly.
The end result is that no buffer will be selected, and hence a completion
with '0' as the result will be posted, without a buffer attached.
NeilBrown [Wed, 28 Aug 2024 23:06:28 +0000 (09:06 +1000)]
nfsd: fix nfsd4_deleg_getattr_conflict in presence of third party lease
It is not safe to dereference fl->c.flc_owner without first confirming
fl->fl_lmops is the expected manager. nfsd4_deleg_getattr_conflict()
tests fl_lmops but largely ignores the result and assumes that flc_owner
is an nfs4_delegation anyway. This is wrong.
With this patch we restore the "!= &nfsd_lease_mng_ops" case to behave
as it did before the change mentioned below. This is the same as the
current code, but without any reference to a possible delegation.
Fixes: c5967721e106 ("NFSD: handle GETATTR conflict with write delegation") Signed-off-by: NeilBrown <[email protected]> Reviewed-by: Jeff Layton <[email protected]> Signed-off-by: Chuck Lever <[email protected]>
Jens Axboe [Wed, 28 Aug 2024 15:42:33 +0000 (09:42 -0600)]
io_uring/rsrc: ensure compat iovecs are copied correctly
For buffer registration (or updates), a userspace iovec is copied in
and updated. If the application is within a compat syscall, then the
iovec type is compat_iovec rather than iovec. However, the type used
in __io_sqe_buffers_update() and io_sqe_buffers_register() is always
struct iovec, and hence the source is incremented by the size of a
non-compat iovec in the loop. This misses every other iovec in the
source, and will run into garbage half way through the copies and
return -EFAULT to the application.
Maintain the source address separately and assign to our user vec
pointer, so that copies always happen from the right source address.
While in there, correct a bad placement of __user which triggered
the following sparse warning prior to this fix:
io_uring/rsrc.c:981:33: warning: cast removes address space '__user' of expression
io_uring/rsrc.c:981:30: warning: incorrect type in assignment (different address spaces)
io_uring/rsrc.c:981:30: expected struct iovec const [noderef] __user *uvec
io_uring/rsrc.c:981:30: got struct iovec *[noderef] __user
Fixes: f4eaf8eda89e ("io_uring/rsrc: Drop io_copy_iov in favor of iovec API") Reviewed-by: Gabriel Krisman Bertazi <[email protected]> Signed-off-by: Jens Axboe <[email protected]>
hongchi.peng [Mon, 26 Aug 2024 02:45:17 +0000 (10:45 +0800)]
drm: komeda: Fix an issue related to normalized zpos
We use komeda_crtc_normalize_zpos to normalize zpos of affected planes
to their blending zorder in CU. If there's only one slave plane in
affected planes and its layer_split property is enabled, order++ for
its split layer, so that when calculating the normalized_zpos
of master planes, the split layer of the slave plane is included, but
the max_slave_zorder does not include the split layer and keep zero
because there's only one slave plane in affacted planes, although we
actually use two slave layers in this commit.
In most cases, this bug does not result in a commit failure, but assume
the following situation:
slave_layer 0: zpos = 0, layer split enabled, normalized_zpos =
0;(use slave_layer 2 as its split layer)
master_layer 0: zpos = 2, layer_split enabled, normalized_zpos =
2;(use master_layer 2 as its split layer)
master_layer 1: zpos = 4, normalized_zpos = 4;
master_layer 3: zpos = 5, normalized_zpos = 5;
kcrtc_st->max_slave_zorder = 0;
When we use master_layer 3 as a input of CU in function
komeda_compiz_set_input and check it with function
komeda_component_check_input, the parameter idx is equal to
normailzed_zpos minus max_slave_zorder, the value of idx is 5
and is euqal to CU's max_active_inputs, so that
komeda_component_check_input returns a -EINVAL value.
To fix the bug described above, when calculating the max_slave_zorder
with the layer_split enabled, count the split layer in this calculation
directly.
Linus Torvalds [Fri, 30 Aug 2024 02:17:30 +0000 (14:17 +1200)]
Merge tag 'drm-fixes-2024-08-30' of https://gitlab.freedesktop.org/drm/kernel
Pull drm fixes from Dave Airlie:
"Another week, another set of GPU fixes. amdgpu and vmwgfx leading the
charge, then i915 and xe changes along with v3d and some other bits.
The TTM revert is due to some stuttering graphical apps probably due
to longer stalls while prefaulting.
i915:
- Fix #11195: The external display connect via USB type-C dock stays
blank after re-connect the dock
- Make DSI backlight work for 2G version of Lenovo Yoga Tab 3 X90F
- Move ARL GuC firmware to correct version
vmwgfx:
- prevent unmapping active read buffers
- fix prime with external buffers
- disable coherent dumb buffers without 3d
v3d:
- disable preemption while updating GPU stats"
* tag 'drm-fixes-2024-08-30' of https://gitlab.freedesktop.org/drm/kernel:
drm/xe/hwmon: Fix WRITE_I1 param from u32 to u16
drm/v3d: Disable preemption while updating GPU stats
drm/amd/pm: Drop unsupported features on smu v14_0_2
drm/amd/pm: Add support for new P2S table revision
drm/amdgpu: support for gc_info table v1.3
drm/amd/display: avoid using null object of framebuffer
drm/amdgpu/gfx12: set UNORD_DISPATCH in compute MQDs
drm/amd/pm: update message interface for smu v14.0.2/3
drm/amdgpu/swsmu: always force a state reprogram on init
drm/amdgpu/smu13.0.7: print index for profiles
drm/amdgpu: align pp_power_profile_mode with kernel docs
drm/i915/dp_mst: Fix MST state after a sink reset
drm/xe: Invalidate media_gt TLBs
drm/i915: ARL requires a newer GSC firmware
drm/i915/dsi: Make Lenovo Yoga Tab 3 X90F DMI match less strict
video/aperture: optionally match the device in sysfb_disable()
drm/vmwgfx: Disable coherent dumb buffers without 3d
drm/vmwgfx: Fix prime with external buffers
drm/vmwgfx: Prevent unmapping active read buffers
Revert "drm/ttm: increase ttm pre-fault value to PMD size"
Dave Airlie [Fri, 30 Aug 2024 01:28:00 +0000 (11:28 +1000)]
Merge tag 'drm-misc-fixes-2024-08-29' of https://gitlab.freedesktop.org/drm/misc/kernel into drm-fixes
A revert for a previous TTM commit causing stuttering, 3 fixes for
vmwgfx related to buffer operations, a fix for video/aperture with
non-VGA primary devices, and a preemption status fix for v3d
Linus Torvalds [Fri, 30 Aug 2024 00:32:53 +0000 (12:32 +1200)]
Merge tag 'execve-v6.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull execve fix from Kees Cook:
- binfmt_elf_fdpic: fix AUXV size with ELF_HWCAP2 (Max Filippov)
* tag 'execve-v6.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
binfmt_elf_fdpic: fix AUXV size calculation when ELF_HWCAP2 is defined
Stephen Brennan [Thu, 29 Aug 2024 18:20:49 +0000 (11:20 -0700)]
dcache: keep dentry_hashtable or d_hash_shift even when not used
The runtime constant feature removes all the users of these variables,
allowing the compiler to optimize them away. It's quite difficult to
extract their values from the kernel text, and the memory saved by
removing them is tiny, and it was never the point of this optimization.
Since the dentry_hashtable is a core data structure, it's valuable for
debugging tools to be able to read it easily. For instance, scripts
built on drgn, like the dentrycache script[1], rely on it to be able to
perform diagnostics on the contents of the dcache. Annotate it as used,
so the compiler doesn't discard it.
Dave Airlie [Thu, 29 Aug 2024 23:02:27 +0000 (09:02 +1000)]
Merge tag 'drm-intel-fixes-2024-08-29' of https://gitlab.freedesktop.org/drm/i915/kernel into drm-fixes
- Fix #11195: The external display connect via USB type-C dock stays blank after re-connect the dock
- Make DSI backlight work for 2G version of Lenovo Yoga Tab 3 X90F
. Move ARL GuC firmware to correct version
-
Linus Torvalds [Thu, 29 Aug 2024 18:14:39 +0000 (06:14 +1200)]
Merge tag 'net-6.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from bluetooth, wireless and netfilter.
No known outstanding regressions.
Current release - regressions:
- wifi: iwlwifi: fix hibernation
- eth: ionic: prevent tx_timeout due to frequent doorbell ringing
Previous releases - regressions:
- sched: fix sch_fq incorrect behavior for small weights
- wifi:
- iwlwifi: take the mutex before running link selection
- wfx: repair open network AP mode
- netfilter: restore IP sanity checks for netdev/egress
- tcp: fix forever orphan socket caused by tcp_abort
- mptcp: close subflow when receiving TCP+FIN
- bluetooth: fix random crash seen while removing btnxpuart driver
Previous releases - always broken:
- mptcp: more fixes for the in-kernel PM
- eth: bonding: change ipsec_lock from spin lock to mutex
- eth: mana: fix race of mana_hwc_post_rx_wqe and new hwc response
Misc:
- documentation: drop special comment style for net code"
* tag 'net-6.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (57 commits)
nfc: pn533: Add poll mod list filling check
mailmap: update entry for Sriram Yagnaraman
selftests: mptcp: join: check re-re-adding ID 0 signal
mptcp: pm: ADD_ADDR 0 is not a new address
selftests: mptcp: join: validate event numbers
mptcp: avoid duplicated SUB_CLOSED events
selftests: mptcp: join: check re-re-adding ID 0 endp
mptcp: pm: fix ID 0 endp usage after multiple re-creations
mptcp: pm: do not remove already closed subflows
selftests: mptcp: join: no extra msg if no counter
selftests: mptcp: join: check re-adding init endp with != id
mptcp: pm: reset MPC endp ID when re-added
mptcp: pm: skip connecting to already established sf
mptcp: pm: send ACK on an active subflow
selftests: mptcp: join: check removing ID 0 endpoint
mptcp: pm: fix RM_ADDR ID for the initial subflow
mptcp: pm: reuse ID 0 after delete and re-add
net: busy-poll: use ktime_get_ns() instead of local_clock()
sctp: fix association labeling in the duplicate COOKIE-ECHO case
mptcp: pr_debug: add missing \n at the end
...
Dmitry Torokhov [Thu, 29 Aug 2024 15:38:54 +0000 (08:38 -0700)]
Input: cypress_ps2 - fix waiting for command response
Commit 8bccf667f62a ("Input: cypress_ps2 - report timeouts when reading
command status") uncovered an existing problem with cypress_ps2 driver:
it tries waiting on a PS/2 device waitqueue without using the rest of
libps2. Unfortunately without it nobody signals wakeup for the
waiting process, and each "extended" command was timing out. But the
rest of the code simply did not notice it.
Fix this by switching from homegrown way of sending request to get
command response and reading it to standard ps2_command() which does
the right thing.
Karthik Poosa [Tue, 27 Aug 2024 15:53:01 +0000 (21:23 +0530)]
drm/xe/hwmon: Fix WRITE_I1 param from u32 to u16
WRITE_I1 sub-command of the POWER_SETUP pcode command accepts a u16
parameter instead of u32. This change prevents potential illegal
sub-command errors.
v2: Mask uval instead of changing the prototype. (Badal)
Aleksandr Mishin [Tue, 27 Aug 2024 08:48:22 +0000 (11:48 +0300)]
nfc: pn533: Add poll mod list filling check
In case of im_protocols value is 1 and tm_protocols value is 0 this
combination successfully passes the check
'if (!im_protocols && !tm_protocols)' in the nfc_start_poll().
But then after pn533_poll_create_mod_list() call in pn533_start_poll()
poll mod list will remain empty and dev->poll_mod_count will remain 0
which lead to division by zero.
Normally no im protocol has value 1 in the mask, so this combination is
not expected by driver. But these protocol values actually come from
userspace via Netlink interface (NFC_CMD_START_POLL operation). So a
broken or malicious program may pass a message containing a "bad"
combination of protocol parameter values so that dev->poll_mod_count
is not incremented inside pn533_poll_create_mod_list(), thus leading
to division by zero.
Call trace looks like:
nfc_genl_start_poll()
nfc_start_poll()
->start_poll()
pn533_start_poll()
Add poll mod list filling check.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Paolo Abeni [Thu, 29 Aug 2024 09:35:54 +0000 (11:35 +0200)]
Merge tag 'nf-24-08-28' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
Patch #1 sets on NFT_PKTINFO_L4PROTO for UDP packets less than 4 bytes
payload from netdev/egress by subtracting skb_network_offset() when
validating IPv4 packet length, otherwise 'meta l4proto udp' never
matches.
Patch #2 subtracts skb_network_offset() when validating IPv6 packet
length for netdev/egress.
netfilter pull request 24-08-28
* tag 'nf-24-08-28' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: nf_tables_ipv6: consider network offset in netdev/egress validation
netfilter: nf_tables: restore IP sanity checks for netdev/egress
====================
====================
mptcp: more fixes for the in-kernel PM
Here is a new batch of fixes for the MPTCP in-kernel path-manager:
Patch 1 ensures the address ID is set to 0 when the path-manager sends
an ADD_ADDR for the address of the initial subflow. The same fix is
applied when a new subflow is created re-using this special address. A
fix for v6.0.
Patch 2 is similar, but for the case where an endpoint is removed: if
this endpoint was used for the initial address, it is important to send
a RM_ADDR with this ID set to 0, and look for existing subflows with the
ID set to 0. A fix for v6.0 as well.
Patch 3 validates the two previous patches.
Patch 4 makes the PM selecting an "active" path to send an address
notification in an ACK, instead of taking the first path in the list. A
fix for v5.11.
Patch 5 fixes skipping the establishment of a new subflow if a previous
subflow using the same pair of addresses is being closed. A fix for
v5.13.
Patch 6 resets the ID linked to the initial subflow when the linked
endpoint is re-added, possibly with a different ID. A fix for v6.0.
Patch 7 validates the three previous patches.
Patch 8 is a small fix for the MPTCP Join selftest, when being used with
older subflows not supporting all MIB counters. A fix for a commit
introduced in v6.4, but backported up to v5.10.
Patch 9 avoids the PM to try to close the initial subflow multiple
times, and increment counters while nothing happened. A fix for v5.10.
Patch 10 stops incrementing local_addr_used and add_addr_accepted
counters when dealing with the address ID 0, because these counters are
not taking into account the initial subflow, and are then not
decremented when the linked addresses are removed. A fix for v6.0.
Patch 11 validates the previous patch.
Patch 12 avoids the PM to send multiple SUB_CLOSED events for the
initial subflow. A fix for v5.12.
Patch 13 validates the previous patch.
Patch 14 stops treating the ADD_ADDR 0 as a new address, and accepts it
in order to re-create the initial subflow if it has been closed, even if
the limit for *new* addresses -- not taking into account the address of
the initial subflow -- has been reached. A fix for v5.10.
Patch 15 validates the previous patch.
Signed-off-by: Matthieu Baerts (NGI0) <[email protected]>
---
Matthieu Baerts (NGI0) (15):
mptcp: pm: reuse ID 0 after delete and re-add
mptcp: pm: fix RM_ADDR ID for the initial subflow
selftests: mptcp: join: check removing ID 0 endpoint
mptcp: pm: send ACK on an active subflow
mptcp: pm: skip connecting to already established sf
mptcp: pm: reset MPC endp ID when re-added
selftests: mptcp: join: check re-adding init endp with != id
selftests: mptcp: join: no extra msg if no counter
mptcp: pm: do not remove already closed subflows
mptcp: pm: fix ID 0 endp usage after multiple re-creations
selftests: mptcp: join: check re-re-adding ID 0 endp
mptcp: avoid duplicated SUB_CLOSED events
selftests: mptcp: join: validate event numbers
mptcp: pm: ADD_ADDR 0 is not a new address
selftests: mptcp: join: check re-re-adding ID 0 signal
selftests: mptcp: join: check re-re-adding ID 0 signal
This test extends "delete re-add signal" to validate the previous
commit: when the 'signal' endpoint linked to the initial subflow (ID 0)
is re-added multiple times, it will re-send the ADD_ADDR with id 0. The
client should still be able to re-create this subflow, even if the
add_addr_accepted limit has been reached as this special address is not
considered as a new address.
The 'Fixes' tag here below is the same as the one from the previous
commit: this patch here is not fixing anything wrong in the selftests,
but it validates the previous fix for an issue introduced by this commit
ID.
The ADD_ADDR 0 with the address from the initial subflow should not be
considered as a new address: this is not something new. If the host
receives it, it simply means that the address is available again.
When receiving an ADD_ADDR for the ID 0, the PM already doesn't consider
it as new by not incrementing the 'add_addr_accepted' counter. But the
'accept_addr' might not be set if the limit has already been reached:
this can be bypassed in this case. But before, it is important to check
that this ADD_ADDR for the ID 0 is for the same address as the initial
subflow. If not, it is not something that should happen, and the
ADD_ADDR can be ignored.
Note that if an ADD_ADDR is received while there is already a subflow
opened using the same address, this ADD_ADDR is ignored as well. It
means that if multiple ADD_ADDR for ID 0 are received, there will not be
any duplicated subflows created by the client.
This test extends "delete and re-add" and "delete re-add signal" to
validate the previous commit: the number of MPTCP events are checked to
make sure there are no duplicated or unexpected ones.
A new helper has been introduced to easily check these events. The
missing events have been added to the lib.
The 'Fixes' tag here below is the same as the one from the previous
commit: this patch here is not fixing anything wrong in the selftests,
but it validates the previous fix for an issue introduced by this commit
ID.
The initial subflow might have already been closed, but still in the
connection list. When the worker is instructed to close the subflows
that have been marked as closed, it might then try to close the initial
subflow again.
A consequence of that is that the SUB_CLOSED event can be seen twice:
# ip mptcp endpoint
1.1.1.1 id 1 subflow dev eth0
2.2.2.2 id 2 subflow dev eth1
# ip mptcp endpoint delete id 1
[ SF_CLOSED] remid=0 locid=0 saddr4=1.1.1.1 daddr4=9.9.9.9
[ SF_CLOSED] remid=0 locid=0 saddr4=1.1.1.1 daddr4=9.9.9.9
The first one is coming from mptcp_pm_nl_rm_subflow_received(), and the
second one from __mptcp_close_subflow().
To avoid doing the post-closed processing twice, the subflow is now
marked as closed the first time.
Note that it is not enough to check if we are dealing with the first
subflow and check its sk_state: the subflow might have been reset or
closed before calling mptcp_close_ssk().
selftests: mptcp: join: check re-re-adding ID 0 endp
This test extends "delete and re-add" to validate the previous commit:
when the endpoint linked to the initial subflow (ID 0) is re-added
multiple times, it was no longer being used, because the internal linked
counters are not decremented for this special endpoint: it is not an
additional endpoint.
Here, the "del/add id 0" steps are done 3 times to unsure this case is
validated.
The 'Fixes' tag here below is the same as the one from the previous
commit: this patch here is not fixing anything wrong in the selftests,
but it validates the previous fix for an issue introduced by this commit
ID.
mptcp: pm: fix ID 0 endp usage after multiple re-creations
'local_addr_used' and 'add_addr_accepted' are decremented for addresses
not related to the initial subflow (ID0), because the source and
destination addresses of the initial subflows are known from the
beginning: they don't count as "additional local address being used" or
"ADD_ADDR being accepted".
It is then required not to increment them when the entrypoint used by
the initial subflow is removed and re-added during a connection. Without
this modification, this entrypoint cannot be removed and re-added more
than once.
It is possible to have in the list already closed subflows, e.g. the
initial subflow has been already closed, but still in the list. No need
to try to close it again, and increments the related counters again.
selftests: mptcp: join: check re-adding init endp with != id
The initial subflow has a special local ID: 0. It is specific per
connection.
When a global endpoint is deleted and re-added later, it can have a
different ID, but the kernel should still use the ID 0 if it corresponds
to the initial address.
This test validates this behaviour: the endpoint linked to the initial
subflow is removed, and re-added with a different ID.
Note that removing the initial subflow will not decrement the 'subflows'
counters, which corresponds to the *additional* subflows. On the other
hand, when the same endpoint is re-added, it will increment this
counter, as it will be seen as an additional subflow this time.
The 'Fixes' tag here below is the same as the one from the previous
commit: this patch here is not fixing anything wrong in the selftests,
but it validates the previous fix for an issue introduced by this commit
ID.
The initial subflow has a special local ID: 0. It is specific per
connection.
When a global endpoint is deleted and re-added later, it can have a
different ID -- most services managing the endpoints automatically don't
force the ID to be the same as before. It is then important to track
these modifications to be consistent with the ID being used for the
address used by the initial subflow, not to confuse the other peer or to
send the ID 0 for the wrong address.
Now when removing an endpoint, msk->mpc_endpoint_id is reset if it
corresponds to this endpoint. When adding a new endpoint, the same
variable is updated if the address match the one of the initial subflow.
mptcp: pm: skip connecting to already established sf
The lookup_subflow_by_daddr() helper checks if there is already a
subflow connected to this address. But there could be a subflow that is
closing, but taking time due to some reasons: latency, losses, data to
process, etc.
If an ADD_ADDR is received while the endpoint is being closed, it is
better to try connecting to it, instead of rejecting it: the peer which
has sent the ADD_ADDR will not be notified that the ADD_ADDR has been
rejected for this reason, and the expected subflow will not be created
at the end.
This helper should then only look for subflows that are established, or
going to be, but not the ones being closed.
Taking the first one on the list doesn't work in some cases, e.g. if the
initial subflow is being removed. Pick another one instead of not
sending anything.
selftests: mptcp: join: check removing ID 0 endpoint
Removing the endpoint linked to the initial subflow should trigger a
RM_ADDR for the right ID, and the removal of the subflow. That's what is
now being verified in the "delete and re-add" test.
Note that removing the initial subflow will not decrement the 'subflows'
counters, which corresponds to the *additional* subflows. On the other
hand, when the same endpoint is re-added, it will increment this
counter, as it will be seen as an additional subflow this time.
The 'Fixes' tag here below is the same as the one from the previous
commit: this patch here is not fixing anything wrong in the selftests,
but it validates the previous fix for an issue introduced by this commit
ID.
The initial subflow has a special local ID: 0. When an endpoint is being
deleted, it is then important to check if its address is not linked to
the initial subflow to send the right ID.
If there was an endpoint linked to the initial subflow, msk's
mpc_endpoint_id field will be set. We can then use this info when an
endpoint is being removed to see if it is linked to the initial subflow.
So now, the correct IDs are passed to mptcp_pm_nl_rm_addr_or_subflow(),
it is no longer needed to use mptcp_local_id_match().
When the endpoint used by the initial subflow is removed and re-added
later, the PM has to force the ID 0, it is a special case imposed by the
MPTCP specs.
Note that the endpoint should then need to be re-added reusing the same
ID.
Linus Torvalds [Thu, 29 Aug 2024 01:59:18 +0000 (13:59 +1200)]
Merge tag 'random-6.11-rc6-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random
Pull random number generator fix from Jason Donenfeld:
"Reject invalid flags passed to vgetrandom() in the same way that
getrandom() does, so that the behavior is the same, from Yann.
The flags argument to getrandom() only has a behavioral effect on the
function if the RNG isn't initialized yet, so vgetrandom() falls back
to the syscall in that case. But if the RNG is initialized, all of the
flags behave the same way, so vgetrandom() didn't bother checking
them, and just ignored them entirely.
But that doesn't account for invalid flags passed in, which need to be
rejected so we can use them later"
* tag 'random-6.11-rc6-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random:
random: vDSO: reject unknown getrandom() flags
Eric Dumazet [Tue, 27 Aug 2024 11:49:16 +0000 (11:49 +0000)]
net: busy-poll: use ktime_get_ns() instead of local_clock()
Typically, busy-polling durations are below 100 usec.
When/if the busy-poller thread migrates to another cpu,
local_clock() can be off by +/-2msec or more for small
values of HZ, depending on the platform.
Use ktimer_get_ns() to ensure deterministic behavior,
which is the whole point of busy-polling.
Jakub Kicinski [Wed, 28 Aug 2024 23:54:44 +0000 (16:54 -0700)]
Merge tag 'wireless-2024-08-28' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Johannes Berg says:
====================
Regressions:
* wfx: fix for open network connection
* iwlwifi: fix for hibernate (due to fast resume feature)
* iwlwifi: fix for a few warnings that were recently added
(had previously been messages not warnings)
Previously broken:
* mwifiex: fix static structures used for per-device data
* iwlwifi: some harmless FW related messages were tagged
too high priority
* iwlwifi: scan buffers weren't checked correctly
* mac80211: SKB leak on beacon error path
* iwlwifi: fix ACPI table interop with certain BIOSes
* iwlwifi: fix locking for link selection
* mac80211: fix SSID comparison in beacon validation
* tag 'wireless-2024-08-28' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
wifi: iwlwifi: clear trans->state earlier upon error
wifi: wfx: repair open network AP mode
wifi: mac80211: free skb on error path in ieee80211_beacon_get_ap()
wifi: iwlwifi: mvm: don't wait for tx queues if firmware is dead
wifi: iwlwifi: mvm: allow 6 GHz channels in MLO scan
wifi: iwlwifi: mvm: pause TCM when the firmware is stopped
wifi: iwlwifi: fw: fix wgds rev 3 exact size
wifi: iwlwifi: mvm: take the mutex before running link selection
wifi: iwlwifi: mvm: fix iwl_mvm_max_scan_ie_fw_cmd_room()
wifi: iwlwifi: mvm: fix iwl_mvm_scan_fits() calculation
wifi: iwlwifi: lower message level for FW buffer destination
wifi: iwlwifi: mvm: fix hibernation
wifi: mac80211: fix beacon SSID mismatch handling
wifi: mwifiex: duplicate static structs used in driver instances
====================
Scott Mayhew [Wed, 28 Aug 2024 19:51:29 +0000 (15:51 -0400)]
selinux,smack: don't bypass permissions check in inode_setsecctx hook
Marek Gresko reports that the root user on an NFS client is able to
change the security labels on files on an NFS filesystem that is
exported with root squashing enabled.
The end of the kerneldoc comment for __vfs_setxattr_noperm() states:
* This function requires the caller to lock the inode's i_mutex before it
* is executed. It also assumes that the caller will make the appropriate
* permission checks.
nfsd_setattr() does do permissions checking via fh_verify() and
nfsd_permission(), but those don't do all the same permissions checks
that are done by security_inode_setxattr() and its related LSM hooks do.
Since nfsd_setattr() is the only consumer of security_inode_setsecctx(),
simplest solution appears to be to replace the call to
__vfs_setxattr_noperm() with a call to __vfs_setxattr_locked(). This
fixes the above issue and has the added benefit of causing nfsd to
recall conflicting delegations on a file when a client tries to change
its security label.
David Howells [Wed, 28 Aug 2024 20:08:25 +0000 (21:08 +0100)]
cifs: Fix FALLOC_FL_ZERO_RANGE to preflush buffered part of target region
Under certain conditions, the range to be cleared by FALLOC_FL_ZERO_RANGE
may only be buffered locally and not yet have been flushed to the server.
For example:
will write two 4KiB blocks of data, which get buffered in the pagecache,
and then fallocate() is used to clear the first 4KiB block on the server -
but we don't flush the data first, which means the EOF position on the
server is wrong, and so the FSCTL_SET_ZERO_DATA RPC fails (and xfs_io
ignores the error), but then when we try to read it, we see the old data.
Fix this by preflushing any part of the target region that above the
server's idea of the EOF position to force the server to update its EOF
position.
Note, however, that we don't want to simply expand the file by moving the
EOF before doing the FSCTL_SET_ZERO_DATA[*] because someone else might see
the zeroed region or if the RPC fails we then have to try to clean it up or
risk getting corruption.
[*] And we have to move the EOF first otherwise FSCTL_SET_ZERO_DATA won't
do what we want.
This fixes the generic/008 xfstest.
[!] Note: A better way to do this might be to split the operation into two
parts: we only do FSCTL_SET_ZERO_DATA for the part of the range below the
server's EOF and then, if that worked, invalidate the buffered pages for the
part above the range.
Arnd Bergmann [Wed, 28 Aug 2024 20:28:51 +0000 (20:28 +0000)]
Merge tag 'riscv-soc-fixes-for-v6.11-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into arm/fixes
RISC-V soc fixes for v6.11-rc6
Prevent an erroneous unconditional report of a timeout during firmware
upload in the mpfs-auto-update driver.
Signed-off-by: Conor Dooley <[email protected]>
* tag 'riscv-soc-fixes-for-v6.11-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
firmware: microchip: fix incorrect error report of programming:timeout on success
Arnd Bergmann [Wed, 28 Aug 2024 20:28:15 +0000 (20:28 +0000)]
Merge tag 'qcom-arm64-fixes-for-6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/fixes
Qualcomm Arm64 DeviceTree fixes for v6.11
On X1E the GPU node is disabled by default, to be enabled in the
individual devices once the developers install the required firmware.
The generic EDP panel driver used on the X1E CRD is replaced with the
Samsung ATNA45AF01 driver, in order to ensure backlight is brought back
up after being turned off.
The pin configuration for PCIe-related pins are corrected across all the
X1E targets. The PCIe controllers gain a minimum OPP vote, and PCIe
domain numbers are corrected.
WiFi calibration variant information is added to the Lenovo Yoga Slim
7x, to pick the right data from the firmware packages.
The incorrect Adreno SMMU global interrupt is corrected.
For IPQ5332, the IRQ triggers for the USB controller are corrected.
Arnd Bergmann [Wed, 28 Aug 2024 20:28:00 +0000 (20:28 +0000)]
Merge tag 'qcom-arm64-defconfig-fixes-for-6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/fixes
Qualcomm Arm64 defconfig fix for 6.11
Enable the Samsung ATNA33XC20 display panel driver, as we switched from
the generic EDP panel for some of the X1E devices in v6.11.
* tag 'qcom-arm64-defconfig-fixes-for-6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
arm64: defconfig: Add CONFIG_DRM_PANEL_SAMSUNG_ATNA33XC20
projects / linux.git / log