Felix Fietkau [Sun, 3 Feb 2019 13:41:22 +0000 (14:41 +0100)]
mt76: measure the time between mt76x02_edcca_check runs
Based on system load and time needed by other calibration runs, the time
between dev->mac_work runs can vary quite a bit.
Calculate busy time based on the actual time difference in order to avoid
potentially over-estimating busy time, which could lead to unnecessary tx
blocking.
Felix Fietkau [Thu, 31 Jan 2019 20:01:24 +0000 (21:01 +0100)]
mt76: fix software encryption issues
Software encrypted packets can be passed not just through the drv_tx callback,
but also through the intermediate tx queue.
In order to deal with that, move the override to mt76x02_mac_write_txwi and
also take care of filling in the per-packet rate information
mt76: move mt76_dma_tx_queue_skb_raw in mt76-core module
Move mt76_dma_tx_queue_skb_raw routine in dma.c and add the
corresponding entry in mt76_queue_ops data structure.
mt76_dma_tx_queue_skb_raw will be reused adding support for
mt7603 driver
mt76x0: eeprom: fix VHT mcs{8,9} rate power offset
Fix rate power configuration for VHT mcs 8 and 9 in
mt76x0_get_tx_power_per_rate. Moreover use the rate power
offset used for HT/VHT mcs 6 even for HT/VHT mcs 7
Fixes: b37bbc8c8251 ("mt76x0: remove eeprom dependency from mt76x0_set_tx_power_per_rate") Signed-off-by: Lorenzo Bianconi <[email protected]> Signed-off-by: Felix Fietkau <[email protected]>
Since we implement beconing on USB now, similar interfaces should be
supported for USB as are for MMIO. Tested only on IBSS mode and
AP mode (not enabled due to lack of PS buffering).
mt76x02: initialize mutli bss mode when set up address
BSSID is not strtirct related with beaconing (for example we can have
2 STA vifs) and more related with MAC address, so initaize BSSID when
setting MAC address.
Use vif_mask to count interfaces to allow to set mac address in HW
if there is only one interface and report error if we create
interface with wrong BSSID resulting in already used index.
Kalle Valo [Mon, 18 Feb 2019 18:10:46 +0000 (20:10 +0200)]
Merge tag 'iwlwifi-next-for-kalle-2019-02-14' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Fourth batch of iwlwifi patches intended for v5.1
* Work on the new debugging infrastructure continues;
* FTM (Fine Timing Measurement) initiator and responder implementation;
* Support for a new device family started;
* Bump supported FW API to 46;
* General bugfixes;
* Other cleanups;
Linus Torvalds [Mon, 18 Feb 2019 17:40:16 +0000 (09:40 -0800)]
Merge tag 'trace-v5.0-rc4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Two more tracing fixes
- Have kprobes not use copy_from_user() to access kernel addresses,
because kprobes can legitimately poke at bad kernel memory, which
will fault. Copy from user code should never fault in kernel space.
Using probe_mem_read() can handle kernel address space faulting.
- Put back the entries counter in the tracing output that was
accidentally removed"
* tag 'trace-v5.0-rc4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix number of entries in trace header
kprobe: Do not use uaccess functions to access kernel memory that can fault
Wei Yongjun [Sat, 16 Feb 2019 08:15:52 +0000 (08:15 +0000)]
net: hns3: make function hclge_set_all_vf_rst() static
Fixes the following sparse warning:
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c:2431:5: warning:
symbol 'hclge_set_all_vf_rst' was not declared. Should it be static?
Fixes: aa5c4f175be6 ("net: hns3: add reset handling for VF when doing PF reset") Signed-off-by: Wei Yongjun <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Wei Yongjun [Sat, 16 Feb 2019 01:48:09 +0000 (01:48 +0000)]
net: sgi: use GFP_ATOMIC under spin lock
The function meth_init_tx_ring() is called from meth_tx_timeout(),
in which spin_lock is held, so we should use GFP_ATOMIC instead.
Fixes: 8d4c28fbc284 ("meth: pass struct device to DMA API functions") Signed-off-by: Wei Yongjun <[email protected]> Signed-off-by: David S. Miller <[email protected]>
David S. Miller [Sun, 17 Feb 2019 23:48:43 +0000 (15:48 -0800)]
Merge branch 'netdev-page_frag_alloc-fixes'
Alexander Duyck says:
====================
Address recent issues found in netdev page_frag_alloc usage
This patch set addresses a couple of issues that I had pointed out to Jann
Horn in response to a recent patch submission.
The first issue is that I wanted to avoid the need to read/modify/write the
size value in order to generate the value for pagecnt_bias. Instead we can
just use a fixed constant which reduces the need for memory read operations
and the overall number of instructions to update the pagecnt bias values.
The other, and more important issue is, that apparently we were letting tun
access the napi_alloc_cache indirectly through netdev_alloc_frag and as a
result letting it create unaligned accesses via unaligned allocations. In
order to prevent this I have added a call to SKB_DATA_ALIGN for the fragsz
field so that we will keep the offset in the napi_alloc_cache
SMP_CACHE_BYTES aligned.
====================
Alexander Duyck [Fri, 15 Feb 2019 22:44:18 +0000 (14:44 -0800)]
net: Do not allocate page fragments that are not skb aligned
This patch addresses the fact that there are drivers, specifically tun,
that will call into the network page fragment allocators with buffer sizes
that are not cache aligned. Doing this could result in data alignment
and DMA performance issues as these fragment pools are also shared with the
skb allocator and any other devices that will use napi_alloc_frags or
netdev_alloc_frags.
Fixes: ffde7328a36d ("net: Split netdev_alloc_frag into __alloc_page_frag and add __napi_alloc_frag") Reported-by: Jann Horn <[email protected]> Signed-off-by: Alexander Duyck <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Alexander Duyck [Fri, 15 Feb 2019 22:44:12 +0000 (14:44 -0800)]
mm: Use fixed constant in page_frag_alloc instead of size + 1
This patch replaces the size + 1 value introduced with the recent fix for 1
byte allocs with a constant value.
The idea here is to reduce code overhead as the previous logic would have
to read size into a register, then increment it, and write it back to
whatever field was being used. By using a constant we can avoid those
memory reads and arithmetic operations in favor of just encoding the
maximum value into the operation itself.
Fixes: 2c2ade81741c ("mm: page_alloc: fix ref bias in page_frag_alloc() for 1-byte allocs") Signed-off-by: Alexander Duyck <[email protected]> Signed-off-by: David S. Miller <[email protected]>
====================
tcp: fix possible crash in tcp_v4_err()
soukjin bae reported a crash in tcp_v4_err() that we
root caused to a missing initialization.
Second patch adds a sanity check in tcp_v4_err() to avoid
future potential problems. Ignoring an ICMP message
is probably better than crashing a machine.
====================
The 1199:68C0 USB ID is reused by Sierra WP7607 which requires the DTR
quirk to be detected. Apply QMI_QUIRK_SET_DTR unconditionally as
already done for other IDs shared between different devices.
Ivan Vecera [Fri, 15 Feb 2019 10:23:25 +0000 (11:23 +0100)]
net: sched: sch_api: set an error msg when qdisc_alloc_handle() fails
This patch sets an error message in extack when the number of qdisc
handles exceeds the maximum. Also the error-code ENOSPC is more
appropriate than ENOMEM in this situation.
Alexandre Torgue [Fri, 15 Feb 2019 09:49:09 +0000 (10:49 +0100)]
net: stmmac: handle endianness in dwmac4_get_timestamp
GMAC IP is little-endian and used on several kind of CPU (big or little
endian). Main callbacks functions of the stmmac drivers take care about
it. It was not the case for dwmac4_get_timestamp function.
Fixes: ba1ffd74df74 ("stmmac: fix PTP support for GMAC4") Signed-off-by: Alexandre Torgue <[email protected]> Signed-off-by: David S. Miller <[email protected]>
net: phy: marvell10g: Don't explicitly set Pause and Asym_Pause
The PHY core expects PHY drivers not to set Pause and Asym_Pause bits,
unless the driver only wants to specify one of them due to HW
limitation. In the case of the Marvell10g driver, we don't need to set
them.
YueHaibing [Fri, 15 Feb 2019 02:36:47 +0000 (02:36 +0000)]
net: dsa: bcm_sf2: Remove set but not used variables 'v6_spec, v6_m_spec'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/dsa/bcm_sf2_cfp.c: In function 'bcm_sf2_cfp_ipv6_rule_set':
drivers/net/dsa/bcm_sf2_cfp.c:606:40: warning:
variable 'v6_m_spec' set but not used [-Wunused-but-set-variable]
drivers/net/dsa/bcm_sf2_cfp.c:606:30: warning:
variable 'v6_spec' set but not used [-Wunused-but-set-variable]
It not used any more after commit e4f7ef54cbd8 ("dsa: bcm_sf2: use flow_rule
infrastructure")
====================
devlink: add the ability to update device flash
This series is the second step to allow trouble shooting and recovering
devices in bad state without the use of netdevs as handles. We can
already query FW versions over devlink, now we add the ability to update
the FW. This will allow drivers to implement some from of "limp-mode"
where the device can't really be used for networking and hence has no
netdev, but we can interrogate it over devlink and fix the broken FW.
Small but nice advantage of devlink is that it only holds the devlink
instance lock during flashing, unlike ethtool which holds rtnl_lock().
====================
Jakub Kicinski [Thu, 14 Feb 2019 21:40:44 +0000 (13:40 -0800)]
devlink: add flash update command
Add devlink flash update command. Advanced NICs have firmware
stored in flash and often cryptographically secured. Updating
that flash is handled by management firmware. Ethtool has a
flash update command which served us well, however, it has two
shortcomings:
- it takes rtnl_lock unnecessarily - really flash update has
nothing to do with networking, so using a networking device
as a handle is suboptimal, which leads us to the second one:
- it requires a functioning netdev - in case device enters an
error state and can't spawn a netdev (e.g. communication
with the device fails) there is no netdev to use as a handle
for flashing.
Devlink already has the ability to report the firmware versions,
now with the ability to update the firmware/flash we will be
able to recover devices in bad state.
To enable updates of sub-components of the FW allow passing
component name. This name should correspond to one of the
versions reported in devlink info.
v1: - replace target id with component name (Jiri).
Heiner Kallweit [Thu, 14 Feb 2019 21:15:31 +0000 (22:15 +0100)]
net: phy: improve phy_resolve_aneg_linkmode
We have the settings array of modes which is sorted based on aneg
priority. Instead of checking each mode manually let's simply iterate
over the sorted settings.
Vlad Buslov [Fri, 15 Feb 2019 15:18:44 +0000 (17:18 +0200)]
net: sched: cgroup: verify that filter is not NULL during walk
Check that filter is not NULL before passing it to tcf_walker->fn()
callback in cls_cgroup_walk(). This can happen when cls_cgroup_change()
failed to set first filter.
Fixes: ed76f5edccc9 ("net: sched: protect filter_chain list with filter_chain_lock mutex") Signed-off-by: Vlad Buslov <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Vlad Buslov [Fri, 15 Feb 2019 15:21:00 +0000 (17:21 +0200)]
net: sched: route: don't set arg->stop in route4_walk() when empty
Some classifiers set arg->stop in their implementation of tp->walk() API
when empty. Most of classifiers do not adhere to that convention. Do not
set arg->stop in route4_walk() to unify tp->walk() behavior among
classifier implementations.
Fixes: ed76f5edccc9 ("net: sched: protect filter_chain list with filter_chain_lock mutex") Signed-off-by: Vlad Buslov <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Vlad Buslov [Fri, 15 Feb 2019 15:20:07 +0000 (17:20 +0200)]
net: sched: fw: don't set arg->stop in fw_walk() when empty
Some classifiers set arg->stop in their implementation of tp->walk() API
when empty. Most of classifiers do not adhere to that convention. Do not
set arg->stop in fw_walk() to unify tp->walk() behavior among classifier
implementations.
Fixes: ed76f5edccc9 ("net: sched: protect filter_chain list with filter_chain_lock mutex") Signed-off-by: Vlad Buslov <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Jann Horn [Thu, 14 Feb 2019 21:35:47 +0000 (22:35 +0100)]
net: caif: use skb helpers instead of open-coding them
Use existing skb_put_data() and skb_trim() instead of open-coding them,
with the skb_put_data() first so that logically, `skb` still contains the
data to be copied in its data..tail area when skb_put_data() reads it.
This change on its own is a cleanup, and it is also necessary for potential
future integration of skbuffs with things like KASAN.
Vadim Pasternak [Thu, 14 Feb 2019 20:22:55 +0000 (20:22 +0000)]
mlxsw: core: Extend thermal module with per QSFP module thermal zones
Add a dedicated thermal zone for each QSFP/SFP module. The current
temperature is obtained from the module's temperature sensor and the
trip points are set based on the warning and critical thresholds
read from the module.
A cooling device (fan) is bound to all the thermal zones. The
thermal zone governor is set to user space in order to avoid
collisions between thermal zones.
For example, one thermal zone might want to increase the speed of
the fan, whereas another one would like to decrease it.
Deferring this decision to user space allows the user to the take
the most suitable decision.
Roopa Prabhu [Thu, 14 Feb 2019 17:15:11 +0000 (09:15 -0800)]
neigh: hook tracepoints in neigh update code
hook tracepoints at the end of functions that
update a neigh entry. neigh_update gets an additional
tracepoint to trace the update flags and old and new
neigh states.
Roopa Prabhu [Thu, 14 Feb 2019 17:15:10 +0000 (09:15 -0800)]
trace: events: add a few neigh tracepoints
The goal here is to trace neigh state changes covering all possible
neigh update paths. Plus have a specific trace point in neigh_update
to cover flags sent to neigh_update.
====================
net: phy: add and use genphy_c45_an_config_an
This series adds genphy_c45_an_config_an() and uses it in the
marvell10g diver. In addition patch 4 aligns the aneg configuration
with what is done in genphy_config_aneg().
v2:
- in patch 2 changed function name to genphy_c45_an_config_aneg
- in patch 3 add a comment regarding 1000BaseT vendor registers
Heiner Kallweit [Sun, 17 Feb 2019 09:32:29 +0000 (10:32 +0100)]
net: phy: marvell10g: check for newly set aneg
Even if the advertisement registers content didn't change, we may have
just switched to aneg, and therefore have to trigger an aneg restart.
This matches the behavior of genphy_config_aneg().
Andrew Lunn [Sun, 17 Feb 2019 09:29:19 +0000 (10:29 +0100)]
net: phy: add genphy_c45_an_config_aneg
C45 configuration of 10/100 and multi-giga bit auto negotiation
advertisement is standardized. Configuration of 1000Base-T however
appears to be vendor specific. Move the generic code out of the
Marvell driver into the common phy-c45.c file.
v2:
- change function name to genphy_c45_an_config_aneg
Petr Machata [Sun, 17 Feb 2019 07:18:41 +0000 (07:18 +0000)]
mlxsw: __mlxsw_sp_port_headroom_set(): Fix a use of local variable
The function-local variable "delay" enters the loop interpreted as delay
in bits. However, inside the loop it gets overwritten by the result of
mlxsw_sp_pg_buf_delay_get(), and thus leaves the loop as quantity in
cells. Thus on second and further loop iterations, the headroom for a
given priority is configured with a wrong size.
Fix by introducing a loop-local variable, delay_cells. Rename thres to
thres_cells for consistency.
Linus Torvalds [Sun, 17 Feb 2019 17:22:01 +0000 (09:22 -0800)]
Merge branch 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI fixes from Ingo Molnar:
"This tree reverts a GICv3 commit (which was broken) and fixes it in
another way, by adding a memblock build-time entries quirk for ARM64"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/arm: Revert "Defer persistent reservations until after paging_init()"
arm64, mm, efi: Account for GICv3 LPI tables in static memblock reserve table
Linus Torvalds [Sun, 17 Feb 2019 16:44:38 +0000 (08:44 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Three changes:
- An UV fix/quirk to pull UV BIOS calls into the efi_runtime_lock
locking regime. (This done by aliasing __efi_uv_runtime_lock to
efi_runtime_lock, which should make the quirk nature obvious and
maintain the general policy that the EFI lock (name...) isn't
exposed to drivers.)
- Our version of MAGA: Make a.out Great Again.
- Add a new Intel model name enumerator to an upstream header to help
reduce dependencies going forward"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/platform/UV: Use efi_runtime_lock to serialise BIOS calls
x86/CPU: Add Icelake model number
x86/a.out: Clear the dump structure initially
Linus Torvalds [Sun, 17 Feb 2019 16:38:13 +0000 (08:38 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Two fixes on the kernel side: fix an over-eager condition that failed
larger perf ring-buffer sizes, plus fix crashes in the Intel BTS code
for a corner case, found by fuzzing"
Linus Torvalds [Sun, 17 Feb 2019 16:36:21 +0000 (08:36 -0800)]
Merge tag 'powerpc-5.0-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fix from Michael Ellerman:
"Just one fix, for pgd/pud_present() which were broken on big endian
since v4.20, leading to possible data corruption.
Thanks to: Aneesh Kumar K.V., Erhard F., Jan Kara"
* tag 'powerpc-5.0-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64s: Fix possible corruption on big endian due to pgd/pud_present()
Linus Torvalds [Sun, 17 Feb 2019 16:34:10 +0000 (08:34 -0800)]
Merge tag 'csky-for-linus-5.0-rc6' of git://github.com/c-sky/csky-linux
Pull arch/csky fixes from Guo Ren:
"Here are some fixup patches for 5.0-rc6"
* tag 'csky-for-linus-5.0-rc6' of git://github.com/c-sky/csky-linux:
csky: Fixup dead loop in show_stack
csky: Fixup io-range page attribute for mmap("/dev/mem")
csky: coding convention: Use task_stack_page
csky: Fixup wrong pt_regs size
csky: Fixup _PAGE_GLOBAL bit for 610 tlb entry
Linus Torvalds [Sun, 17 Feb 2019 16:32:25 +0000 (08:32 -0800)]
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Two more driver bugfixes"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: bcm2835: Clear current buffer pointers and counts after a transfer
i2c: cadence: Fix the hold bit setting
Linus Torvalds [Sun, 17 Feb 2019 16:30:35 +0000 (08:30 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
- tweaks to Elan drivers (both PS/2 and I2C) to support new devices.
Also revert of one of IDs as that device should really be driven by
i2c-hid + hid-multitouch
- a few drivers have been switched to set_brightness_blocking() call
because they either were sleeping the their set_brightness()
implementation or used workqueue but were not canceling it on unbind.
- ps2-gpio and matrix_keypad needed to [properly] flush their works to
avoid potential use-after-free on unbind.
- other miscellaneous fixes.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elan_i2c - add ACPI ID for touchpad in Lenovo V330-15ISK
Input: st-keyscan - fix potential zalloc NULL dereference
Input: apanel - switch to using brightness_set_blocking()
Revert "Input: elan_i2c - add ACPI ID for touchpad in ASUS Aspire F5-573G"
Input: qt2160 - switch to using brightness_set_blocking()
Input: matrix_keypad - use flush_delayed_work()
Input: ps2-gpio - flush TX work when closing port
Input: cap11xx - switch to using set_brightness_blocking()
Input: elantech - enable 3rd button support on Fujitsu CELSIUS H780
Input: bma150 - register input device after setting private data
Input: pwm-vibra - stop regulator after disabling pwm, not before
Input: pwm-vibra - prevent unbalanced regulator
Input: snvs_pwrkey - allow selecting driver for i.MX 7D
Linus Torvalds [Sun, 17 Feb 2019 16:28:49 +0000 (08:28 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"A somewhat bigger ARM update, and the usual smattering of x86 bug
fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: vmx: Fix entry number check for add_atomic_switch_msr()
KVM: x86: Recompute PID.ON when clearing PID.SN
KVM: nVMX: Restore a preemption timer consistency check
x86/kvm/nVMX: read from MSR_IA32_VMX_PROCBASED_CTLS2 only when it is available
KVM: arm64: Forbid kprobing of the VHE world-switch code
KVM: arm64: Relax the restriction on using stage2 PUD huge mapping
arm: KVM: Add missing kvm_stage2_has_pmd() helper
KVM: arm/arm64: vgic: Always initialize the group of private IRQs
arm/arm64: KVM: Don't panic on failure to properly reset system registers
arm/arm64: KVM: Allow a VCPU to fully reset itself
KVM: arm/arm64: Reset the VCPU without preemption and vcpu state loaded
arm64: KVM: Don't generate UNDEF when LORegion feature is present
KVM: arm/arm64: vgic: Make vgic_cpu->ap_list_lock a raw_spinlock
KVM: arm/arm64: vgic: Make vgic_dist->lpi_list_lock a raw_spinlock
KVM: arm/arm64: vgic: Make vgic_irq->irq_lock a raw_spinlock
Dmitry Torokhov [Wed, 6 Feb 2019 18:32:46 +0000 (10:32 -0800)]
Input: apanel - switch to using brightness_set_blocking()
Now that LEDs core allows "blocking" flavor of "set brightness" method we
can use it and get rid of private work item. As a bonus, we are no longer
forgetting to cancel it when we unbind the driver.
Unfortunately this is broken on big endian, as the result of the
bitwise & is truncated to int, which is always zero because
_PAGE_PRESENT is 0x8000000000000000ul. This means pgd_present() and
pud_present() are always false at compile time, and the compiler
elides the subsequent code.
Remarkably with that bug present we are still able to boot and run
with few noticeable effects. However under some work loads we are able
to trigger a warning in the ext4 code:
Andrii Nakryiko [Sat, 16 Feb 2019 03:52:18 +0000 (19:52 -0800)]
tools/libbpf: support bigger BTF data sizes
While it's understandable why kernel limits number of BTF types to 65535
and size of string section to 64KB, in libbpf as user-space library it's
too restrictive. E.g., pahole converting DWARF to BTF type information
for Linux kernel generates more than 3 million BTF types and more than
3MB of strings, before deduplication. So to allow btf__dedup() to do its
work, we need to be able to load bigger BTF sections using btf__new().
- add negative tests (no routes, explicitly unreachable destinations)
to exercize error handling code paths;
- do not exit on test failures, but instead print a summary of
passed/failed tests at the end.
Alexandre Torgue [Thu, 14 Feb 2019 16:03:44 +0000 (17:03 +0100)]
net: stmmac: use correct define to get rx timestamp on GMAC4
In dwmac4_wrback_get_rx_timestamp_status we looking for a RX timestamp.
For that receive descriptors are handled and so we should use defines
related to receive descriptors. It'll no change the functional behavior
as RDES3_RDES1_VALID=TDES3_RS1V=BIT(26) but it makes code easier to read.
Dan Carpenter [Thu, 14 Feb 2019 06:56:35 +0000 (09:56 +0300)]
atm: clean up vcc_seq_next()
It's confusing to call PTR_ERR(v). The PTR_ERR() function is basically
a fancy cast to long so it makes you wonder, was IS_ERR() intended? But
that doesn't make sense because vcc_walk() doesn't return error
pointers.
This patch doesn't affect runtime, it's just a cleanup.
Guillaume Nault [Wed, 13 Feb 2019 03:30:34 +0000 (04:30 +0100)]
sock: consistent handling of extreme SO_SNDBUF/SO_RCVBUF values
SO_SNDBUF and SO_RCVBUF (and their *BUFFORCE version) may overflow or
underflow their input value. This patch aims at providing explicit
handling of these extreme cases, to get a clear behaviour even with
values bigger than INT_MAX / 2 or lower than INT_MIN / 2.
For simplicity, only SO_SNDBUF and SO_SNDBUFFORCE are described here,
but the same explanation and fix apply to SO_RCVBUF and SO_RCVBUFFORCE
(with 'SNDBUF' replaced by 'RCVBUF' and 'wmem_max' by 'rmem_max').
Overflow of positive values
===========================
When handling SO_SNDBUF or SO_SNDBUFFORCE, if 'val' exceeds
INT_MAX / 2, the buffer size is set to its minimum value because
'val * 2' overflows, and max_t() considers that it's smaller than
SOCK_MIN_SNDBUF. For SO_SNDBUF, this can only happen with
net.core.wmem_max > INT_MAX / 2.
SO_SNDBUF and SO_SNDBUFFORCE are actually designed to let users probe
for the maximum buffer size by setting an arbitrary large number that
gets capped to the maximum allowed/possible size. Having the upper
half of the positive integer space to potentially reduce the buffer
size to its minimum value defeats this purpose.
This patch caps the base value to INT_MAX / 2, so that bigger values
don't overflow and keep setting the buffer size to its maximum.
Underflow of negative values
============================
For negative numbers, SO_SNDBUF always considers them bigger than
net.core.wmem_max, which is bounded by [SOCK_MIN_SNDBUF, INT_MAX].
Therefore such values are set to net.core.wmem_max and we're back to
the behaviour of positive integers described above (return maximum
buffer size if wmem_max <= INT_MAX / 2, return SOCK_MIN_SNDBUF
otherwise).
However, SO_SNDBUFFORCE behaves differently. The user value is
directly multiplied by two and compared with SOCK_MIN_SNDBUF. If
'val * 2' doesn't underflow or if it underflows to a value smaller
than SOCK_MIN_SNDBUF then buffer size is set to its minimum value.
Otherwise the buffer size is set to the underflowed value.
This patch treats negative values passed to SO_SNDBUFFORCE as null, to
prevent underflows. Therefore negative values now always set the buffer
size to its minimum value.
Even though SO_SNDBUF behaves inconsistently by setting buffer size to
the maximum value when passed a negative number, no attempt is made to
modify this behaviour. There may exist some programs that rely on using
negative numbers to set the maximum buffer size. Avoiding overflows
because of extreme net.core.wmem_max values is the most we can do here.
Summary of altered behaviours
=============================
val : user-space value passed to setsockopt()
val_uf : the underflowed value resulting from doubling val when
val < INT_MIN / 2
wmem_max : short for net.core.wmem_max
val_cap : min(val, wmem_max)
min_len : minimal buffer length (that is, SOCK_MIN_SNDBUF)
max_len : maximal possible buffer length, regardless of wmem_max (that
is, INT_MAX - 1)
^^^^ : altered behaviour
SO_SNDBUF:
+-------------------------+-------------+------------+----------------+
| CONDITION | OLD RESULT | NEW RESULT | COMMENT |
+-------------------------+-------------+------------+----------------+
| val < 0 && | | | No overflow, |
| wmem_max <= INT_MAX/2 | wmem_max*2 | wmem_max*2 | keep original |
| | | | behaviour |
+-------------------------+-------------+------------+----------------+
| val < 0 && | | | Cap wmem_max |
| INT_MAX/2 < wmem_max | min_len | max_len | to prevent |
| | | ^^^^^^^ | overflow |
+-------------------------+-------------+------------+----------------+
| 0 <= val <= min_len/2 | min_len | min_len | Ordinary case |
+-------------------------+-------------+------------+----------------+
| min_len/2 < val && | val_cap*2 | val_cap*2 | Ordinary case |
| val_cap <= INT_MAX/2 | | | |
+-------------------------+-------------+------------+----------------+
| min_len < val && | | | Cap val_cap |
| INT_MAX/2 < val_cap | min_len | max_len | again to |
| (implies that | | ^^^^^^^ | prevent |
| INT_MAX/2 < wmem_max) | | | overflow |
+-------------------------+-------------+------------+----------------+
SO_SNDBUFFORCE:
+------------------------------+---------+---------+------------------+
| CONDITION | BEFORE | AFTER | COMMENT |
| | PATCH | PATCH | |
+------------------------------+---------+---------+------------------+
| val < INT_MIN/2 && | min_len | min_len | Underflow with |
| val_uf <= min_len | | | no consequence |
+------------------------------+---------+---------+------------------+
| val < INT_MIN/2 && | val_uf | min_len | Set val to 0 to |
| val_uf > min_len | | ^^^^^^^ | avoid underflow |
+------------------------------+---------+---------+------------------+
| INT_MIN/2 <= val < 0 | min_len | min_len | No underflow |
+------------------------------+---------+---------+------------------+
| 0 <= val <= min_len/2 | min_len | min_len | Ordinary case |
+------------------------------+---------+---------+------------------+
| min_len/2 < val <= INT_MAX/2 | val*2 | val*2 | Ordinary case |
+------------------------------+---------+---------+------------------+
| INT_MAX/2 < val | min_len | max_len | Cap val to |
| | | ^^^^^^^ | prevent overflow |
+------------------------------+---------+---------+------------------+
Linus Torvalds [Sun, 17 Feb 2019 01:44:12 +0000 (17:44 -0800)]
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"This week is a much smaller update, containing fixes only for TI OMAP,
NXP i.MX and Rockchips platforms:
omap:
- omap4 had problems with lost timer interrupts
- another IRQ handling issue with OMAP5
- A workaround for a regression in the pwm-omap-dmtimer driver
NXP i.MX:
- eMMC was broken on the new imx8mq-evk board
Rockchip:
- a fix for new dtc graph warnings and a regulator fix for rock64
- USB support broke on rk3328-rock64"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: OMAP2+: fix lack of timer interrupts on CPU1 after hotplug
arm64: dts: imx8mq: Fix boot from eMMC
ARM: OMAP2+: Variable "reg" in function omap4_dsi_mux_pads() could be uninitialized
ARM: dts: Configure clock parent for pwm vibra
bus: ti-sysc: Fix timer handling with drop pm_runtime_irq_safe()
arm64: dts: rockchip: enable usb-host regulators at boot on rk3328-rock64
arm64: dts: rockchip: fix graph_port warning on rk3399 bob kevin and excavator
ARM: OMAP5+: Fix inverted nirq pin interrupts with irq_set_type
clocksource: timer-ti-dm: Fix pwm dmtimer usage of fck reparenting
ARM: dts: rockchip: remove qos_cif1 from rk3188 power-domain
Linus Torvalds [Sun, 17 Feb 2019 01:38:01 +0000 (17:38 -0800)]
Merge tag 'nfsd-5.0-2' of git://linux-nfs.org/~bfields/linux
Pull more nfsd fixes from Bruce Fields:
"Two small fixes, one for crashes using nfs/krb5 with older enctypes,
one that could prevent clients from reclaiming state after a kernel
upgrade"
* tag 'nfsd-5.0-2' of git://linux-nfs.org/~bfields/linux:
sunrpc: fix 4 more call sites that were using stack memory with a scatterlist
Revert "nfsd4: return default lease period"
Linus Torvalds [Sun, 17 Feb 2019 01:33:39 +0000 (17:33 -0800)]
Merge tag 'nfs-for-5.0-4' of git://git.linux-nfs.org/projects/anna/linux-nfs
Pull more NFS client fixes from Anna Schumaker:
"Three fixes this time.
Nicolas's is for xprtrdma completion vector allocation on single-core
systems. Greg's adds an error check when allocating a debugfs dentry.
And Ben's is an additional fix for nfs_page_async_flush() to prevent
pages from accidentally getting truncated.
Summary:
- Make sure Send CQ is allocated on an existing compvec
- Properly check debugfs dentry before using it
- Don't use page_file_mapping() after removing a page"
* tag 'nfs-for-5.0-4' of git://git.linux-nfs.org/projects/anna/linux-nfs:
NFS: Don't use page_file_mapping after removing the page
rpc: properly check debugfs dentry before using it
xprtrdma: Make sure Send CQ is allocated on an existing compvec
David S. Miller [Sat, 16 Feb 2019 21:44:39 +0000 (13:44 -0800)]
net: Add header for usage of fls64()
Fixes: 3b89ea9c5902 ("net: Fix for_each_netdev_feature on Big endian") Suggested-by: Eric Dumazet <[email protected]> Signed-off-by: David S. Miller <[email protected]>
David S. Miller [Sat, 16 Feb 2019 20:11:17 +0000 (12:11 -0800)]
Merge tag 'mlx5-updates-2019-02-15' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Support Mellanox BlueField SmartNIC (mlx5-updates-2019-02-15)
Bodong Wang says,
BlueField device is a multi-core ARM processor in a highly integrated
system on chip coupled with the ConnectX interconnect controller.
BlueField device can be presented in one out of two modes:
- SEPARATED_HOST: ARM processors as a separated and orthogonal host
like any other external host in the multi-host virtualization model.
- EMBEDDED_CPU: ARM processors as Embedded CPU (EC) and part of the
external hosts virtualization model.
While existing driver already supports the device on separated_host
mode, this patch series focus on the functionalities of embedded_cpu
mode.
On embedded_cpu mode, BlueField device exposes regular network
controller PCI function in the BlueField host(e.g, x86). However, a
separate PCI function called Embedded CPU Physical Function(ECPF) is
also added to the ARM host side, where standard Linux distributions is
able to run on the ARM cores. Depends on the NV configuration from
firmware, ECPF can be the e-switch manager and firmware pages supplier.
If ECPF is configured as e-switch manager and page supplier, it will
take over the responsibilities from the PF on BlueField host includes:
- Owns, controls and manages all e-switch parts, and takes e-switch
traffic by default. It also should perform ENABLE_HCA for the host
PF just like a PF does for its VFs.
- Provides and manages the ICM host memory required for the HCA to
store various contexts for itself, the PF and VFs belong the
e-switch it manages.
The PF on BlueField host side is still responsible for:
- Control its own permanent MAC.
- PCI and SRIOV configurations and perform ENABLE_HCA for its VFs.
The ECPF can also retrieve information about the external host it
controls, like host identifier, PCI BDF and number of virtual functions.
As these parameters may be changed dynamically, an event will be triggered
to the driver on ECPF side.
====================
Linus Torvalds [Sat, 16 Feb 2019 18:28:05 +0000 (10:28 -0800)]
Merge tag 'compiler-attributes-for-linus-v5.0-rc7' of git://github.com/ojeda/linux
Pull compiler attributes fixes from Miguel Ojeda:
"Clean the new GCC 9 -Wmissing-attributes warnings
The upcoming GCC 9 release extends the -Wmissing-attributes warnings
(enabled by -Wall) to C and aliases: it warns when particular function
attributes are missing in the aliases but not in their target, e.g.:
void __cold f(void) {}
void __alias("f") g(void);
diagnoses:
warning: 'g' specifies less restrictive attribute than
its target 'f': 'cold' [-Wmissing-attributes]
These patch series clean these new warnings. Most of them are caused
by the module_init/exit macros"
Link: https://lore.kernel.org/lkml/[email protected]/
* tag 'compiler-attributes-for-linus-v5.0-rc7' of git://github.com/ojeda/linux:
include/linux/module.h: copy __init/__exit attrs to init/cleanup_module
Compiler Attributes: add support for __copy (gcc >= 9)
lib/crc32.c: mark crc32_le_base/__crc32c_le_base aliases as __pure
Ard Biesheuvel [Fri, 15 Feb 2019 12:33:33 +0000 (13:33 +0100)]
efi/arm: Revert "Defer persistent reservations until after paging_init()"
This reverts commit eff896288872d687d9662000ec9ae11b6d61766f, which
deferred the processing of persistent memory reservations to a point
where the memory may have already been allocated and overwritten,
defeating the purpose.
Ard Biesheuvel [Fri, 15 Feb 2019 12:33:32 +0000 (13:33 +0100)]
arm64, mm, efi: Account for GICv3 LPI tables in static memblock reserve table
In the irqchip and EFI code, we have what basically amounts to a quirk
to work around a peculiarity in the GICv3 architecture, which permits
the system memory address of LPI tables to be programmable only once
after a CPU reset. This means kexec kernels must use the same memory
as the first kernel, and thus ensure that this memory has not been
given out for other purposes by the time the ITS init code runs, which
is not very early for secondary CPUs.
On systems with many CPUs, these reservations could overflow the
memblock reservation table, and this was addressed in commit:
eff896288872 ("efi/arm: Defer persistent reservations until after paging_init()")
However, this turns out to have made things worse, since the allocation
of page tables and heap space for the resized memblock reservation table
itself may overwrite the regions we are attempting to reserve, which may
cause all kinds of corruption, also considering that the ITS will still
be poking bits into that memory in response to incoming MSIs.
So instead, let's grow the static memblock reservation table on such
systems so it can accommodate these reservations at an earlier time.
This will permit us to revert the above commit in a subsequent patch.
When enabled, the sip_external_media logic will leave SDP
payload untouched when it detects that interface towards INVITEd
party is the same with the one towards media endpoint.
The typical scenario for this logic is when a LAN SIP agent has more
than one IP address (uses a different address for media streams than
the one used on signalling stream) and it also forwards calls to a
voice mailbox located on the WAN side. In such case sip_direct_media
must be disabled (so normal calls could be handled by the SIP
helper), but media streams that are not traversing this router must
also be excluded from address translation (e.g. call forwards).
projects / linux.git / log