--- /dev/null
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright (c) 2020, Silicon Laboratories, Inc.
+%YAML 1.2
+---
+
+$id: http://devicetree.org/schemas/net/wireless/silabs,wfx.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Silicon Labs WFxxx devicetree bindings
+
+maintainers:
+
+description: >
+ Support for the Wifi chip WFxxx from Silicon Labs. Currently, the only device
+ from the WFxxx series is the WF200 described here:
+ https://www.silabs.com/documents/public/data-sheets/wf200-datasheet.pdf
+
+ The WF200 can be connected via SPI or via SDIO.
+
+ For SDIO:
+
+ Declaring the WFxxx chip in device tree is mandatory (usually, the VID/PID is
+ sufficient for the SDIO devices).
+
+ It is recommended to declare a mmc-pwrseq on SDIO host above WFx. Without
+ it, you may encounter issues during reboot. The mmc-pwrseq should be
+ compatible with mmc-pwrseq-simple. Please consult
+ Documentation/devicetree/bindings/mmc/mmc-pwrseq-simple.yaml for more
+ information.
+
+ For SPI:
+
+ In add of the properties below, please consult
+ Documentation/devicetree/bindings/spi/spi-controller.yaml for optional SPI
+ related properties.
+
+properties:
+ compatible:
+ items:
+ - enum:
++ - prt,prtt1c-wfm200 # Protonic PRTT1C Board
+ - silabs,brd4001a # WGM160P Evaluation Board
+ - silabs,brd8022a # WF200 Evaluation Board
+ - silabs,brd8023a # WFM200 Evaluation Board
+ - const: silabs,wf200 # Chip alone without antenna
+
+ reg:
+ description:
+ When used on SDIO bus, <reg> must be set to 1. When used on SPI bus, it is
+ the chip select address of the device as defined in the SPI devices
+ bindings.
+ maxItems: 1
+
+ spi-max-frequency: true
+
+ interrupts:
+ description: The interrupt line. Should be IRQ_TYPE_EDGE_RISING. When SPI is
+ used, this property is required. When SDIO is used, the "in-band"
+ interrupt provided by the SDIO bus is used unless an interrupt is defined
+ in the Device Tree.
+ maxItems: 1
+
+ reset-gpios:
+ description: (SPI only) Phandle of gpio that will be used to reset chip
+ during probe. Without this property, you may encounter issues with warm
+ boot.
+
+ For SDIO, the reset gpio should declared using a mmc-pwrseq.
+ maxItems: 1
+
+ wakeup-gpios:
+ description: Phandle of gpio that will be used to wake-up chip. Without this
+ property, driver will disable most of power saving features.
+ maxItems: 1
+
+ silabs,antenna-config-file:
+ $ref: /schemas/types.yaml#/definitions/string
+ description: Use an alternative file for antenna configuration (aka
+ "Platform Data Set" in Silabs jargon). Default depends of "compatible"
+ string. For "silabs,wf200", the default is 'wf200.pds'.
+
+ local-mac-address: true
+
+ mac-address: true
+
+additionalProperties: false
+
+required:
+ - compatible
+ - reg
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+
+ spi {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ wifi@0 {
+ compatible = "silabs,brd8022a", "silabs,wf200";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wfx_irq &wfx_gpios>;
+ reg = <0>;
+ interrupts-extended = <&gpio 16 IRQ_TYPE_EDGE_RISING>;
+ wakeup-gpios = <&gpio 12 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+ spi-max-frequency = <42000000>;
+ };
+ };
+
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+
+ wfx_pwrseq: wfx_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wfx_reset>;
+ reset-gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+ };
+
+ mmc {
+ mmc-pwrseq = <&wfx_pwrseq>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ wifi@1 {
+ compatible = "silabs,brd8022a", "silabs,wf200";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wfx_wakeup>;
+ reg = <1>;
+ wakeup-gpios = <&gpio 12 GPIO_ACTIVE_HIGH>;
+ };
+ };
+...
-description:
+description: |
The R-Car (RZ/G) System Controller provides power management for the CPU
cores and various coprocessors.
+ The power domain IDs for consumers are defined in header files::
+ include/dt-bindings/power/r8*-sysc.h
properties:
compatible:
- renesas,r8a77995-sysc # R-Car D3
- renesas,r8a779a0-sysc # R-Car V3U
- renesas,r8a779f0-sysc # R-Car S4-8
+ - renesas,r8a779g0-sysc # R-Car V4H
reg:
maxItems: 1
reg = <0xe6180000 0x0200>;
#power-domain-cells = <1>;
};
-
- - |
- // Power Domain consumers
- #include <dt-bindings/power/r8a7791-sysc.h>
-
- cache-controller-0 {
- compatible = "cache";
- power-domains = <&sysc R8A7791_PD_CA15_SCU>;
- cache-unified;
- cache-level = <2>;
- };
description: Shenzen Chuangsiqi Technology Co.,Ltd.
"^ctera,.*":
description: CTERA Networks Intl.
+ "^ctu,.*":
+ description: Czech Technical University in Prague
"^cubietech,.*":
description: Cubietech, Ltd.
"^cui,.*":
description: Empire Electronix
"^emtrion,.*":
description: emtrion GmbH
+ "^enclustra,.*":
+ description: Enclustra GmbH
"^endless,.*":
description: Endless Mobile, Inc.
"^ene,.*":
description: Sensirion AG
"^sensortek,.*":
description: Sensortek Technology Corporation
+ "^sercomm,.*":
+ description: Sercomm (Suzhou) Corporation
"^sff,.*":
description: Small Form Factor Committee
"^sgd,.*":
description: Sinlinx Electronics Technology Co., LTD
"^sinovoip,.*":
description: SinoVoip Co., Ltd
+ "^sinowealth,.*":
+ description: SINO WEALTH Electronic Ltd.
"^sipeed,.*":
description: Shenzhen Sipeed Technology Co., Ltd.
"^sirf,.*":
description: StorLink Semiconductors, Inc.
"^storm,.*":
description: Storm Semiconductor, Inc.
+ "^storopack,.*":
+ description: Storopack
"^summit,.*":
description: Summit microelectronics
"^sunchip,.*":
pinctrl-0 = <&pinctrl_ecspi4>;
status = "okay";
- flash: m25p80@1 {
+ flash: flash@1 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "micron,n25q128a11", "jedec,spi-nor";
regulators {
bcore1 {
regulator-name = "bcore1";
- regulator-always-on = <1>;
+ regulator-always-on;
regulator-min-microvolt = <300000>;
regulator-max-microvolt = <3300000>;
};
bcore2 {
regulator-name = "bcore2";
- regulator-always-on = <1>;
+ regulator-always-on;
regulator-min-microvolt = <300000>;
regulator-max-microvolt = <3300000>;
};
bpro {
regulator-name = "bpro";
- regulator-always-on = <1>;
+ regulator-always-on;
regulator-min-microvolt = <300000>;
regulator-max-microvolt = <3300000>;
};
bperi {
regulator-name = "bperi";
- regulator-always-on = <1>;
+ regulator-always-on;
regulator-min-microvolt = <300000>;
regulator-max-microvolt = <3300000>;
};
bmem {
regulator-name = "bmem";
- regulator-always-on = <1>;
+ regulator-always-on;
regulator-min-microvolt = <300000>;
regulator-max-microvolt = <3300000>;
};
ldo2 {
regulator-name = "ldo2";
- regulator-always-on = <1>;
+ regulator-always-on;
regulator-min-microvolt = <300000>;
regulator-max-microvolt = <1800000>;
};
ldo3 {
regulator-name = "ldo3";
- regulator-always-on = <1>;
+ regulator-always-on;
regulator-min-microvolt = <300000>;
regulator-max-microvolt = <3300000>;
};
ldo4 {
regulator-name = "ldo4";
- regulator-always-on = <1>;
+ regulator-always-on;
regulator-min-microvolt = <300000>;
regulator-max-microvolt = <3300000>;
};
ldo5 {
regulator-name = "ldo5";
- regulator-always-on = <1>;
+ regulator-always-on;
regulator-min-microvolt = <300000>;
regulator-max-microvolt = <3300000>;
};
ldo6 {
regulator-name = "ldo6";
- regulator-always-on = <1>;
+ regulator-always-on;
regulator-min-microvolt = <300000>;
regulator-max-microvolt = <3300000>;
};
ldo7 {
regulator-name = "ldo7";
- regulator-always-on = <1>;
+ regulator-always-on;
regulator-min-microvolt = <300000>;
regulator-max-microvolt = <3300000>;
};
ldo8 {
regulator-name = "ldo8";
- regulator-always-on = <1>;
+ regulator-always-on;
regulator-min-microvolt = <300000>;
regulator-max-microvolt = <3300000>;
};
ldo9 {
regulator-name = "ldo9";
- regulator-always-on = <1>;
+ regulator-always-on;
regulator-min-microvolt = <300000>;
regulator-max-microvolt = <3300000>;
};
ldo10 {
regulator-name = "ldo10";
- regulator-always-on = <1>;
+ regulator-always-on;
regulator-min-microvolt = <300000>;
regulator-max-microvolt = <3300000>;
};
ldo11 {
regulator-name = "ldo11";
- regulator-always-on = <1>;
+ regulator-always-on;
regulator-min-microvolt = <300000>;
regulator-max-microvolt = <3300000>;
};
bio {
regulator-name = "bio";
- regulator-always-on = <1>;
+ regulator-always-on;
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
brightness-levels = <0 4 8 16 32 64 128 255>;
default-brightness-level = <5>;
power-supply = <®_backlight_en>;
- pwms = <&pwm3 0 5000000>;
+ pwms = <&pwm3 0 5000000 0>;
status = "disabled";
};
st,settling = <2>;
st,fraction-z = <7>;
st,i-drive = <1>;
- touchscreen-inverted-x = <1>;
- touchscreen-inverted-y = <1>;
+ touchscreen-inverted-x;
+ touchscreen-inverted-y;
};
};
};
};
&pwm3 {
- #pwm-cells = <2>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm3>;
status = "disabled";
- // SPDX-License-Identifier: GPL-2.0+ OR MIT
+ // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/*
- * Copyright 2018-2021 Toradex
+ * Copyright 2018-2022 Toradex
*/
#include "imx6ull.dtsi"
/ {
+ /* Ethernet aliases to ensure correct MAC addresses */
aliases {
ethernet0 = &fec2;
ethernet1 = &fec1;
};
- bl: backlight {
+ backlight: backlight {
compatible = "pwm-backlight";
+ brightness-levels = <0 4 8 16 32 64 128 255>;
+ default-brightness-level = <6>;
+ enable-gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_gpio_bl_on>;
- enable-gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
- status = "disabled";
+ power-supply = <®_3v3>;
+ pwms = <&pwm4 0 5000000 1>;
+ status = "okay";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_snvs_gpiokeys>;
+
+ wakeup {
+ debounce-interval = <10>;
+ gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>; /* SODIMM 45 */
+ label = "Wake-Up";
+ linux,code = <KEY_WAKEUP>;
+ wakeup-source;
+ };
+ };
+
+ panel_dpi: panel-dpi {
+ compatible = "edt,et057090dhu";
+ backlight = <&backlight>;
+ power-supply = <®_3v3>;
+ status = "okay";
+
+ port {
+ lcd_panel_in: endpoint {
+ remote-endpoint = <&lcdif_out>;
+ };
+ };
};
reg_module_3v3: regulator-module-3v3 {
regulator-max-microvolt = <3300000>;
};
- reg_sd1_vmmc: regulator-sd1-vmmc {
+ reg_sd1_vqmmc: regulator-sd1-vqmmc {
compatible = "regulator-gpio";
- gpio = <&gpio5 9 GPIO_ACTIVE_HIGH>;
+ gpios = <&gpio5 9 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_snvs_reg_sd>;
regulator-always-on;
states = <1800000 0x1 3300000 0x0>;
vin-supply = <®_module_3v3>;
};
+
+ reg_eth_phy: regulator-eth-phy {
+ compatible = "regulator-fixed-clock";
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "+V3.3_ETH";
+ regulator-type = "voltage";
+ vin-supply = <®_module_3v3>;
+ clocks = <&clks IMX6UL_CLK_ENET2_REF_125M>;
+ startup-delay-us = <150000>;
+ };
};
&adc1 {
num-channels = <10>;
vref-supply = <®_module_3v3_avdd>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_adc1>;
};
&can1 {
pinctrl-0 = <&pinctrl_ecspi1 &pinctrl_ecspi1_cs>;
};
+ /* Ethernet */
&fec2 {
pinctrl-names = "default", "sleep";
pinctrl-0 = <&pinctrl_enet2>;
pinctrl-1 = <&pinctrl_enet2_sleep>;
phy-mode = "rmii";
phy-handle = <ðphy1>;
+ phy-supply = <®_eth_phy>;
status = "okay";
mdio {
};
};
+ /* NAND */
&gpmi {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_gpmi_nand>;
+ fsl,use-minimum-ecc;
nand-on-flash-bbt;
nand-ecc-mode = "hw";
nand-ecc-strength = <8>;
status = "okay";
};
+ /* I2C3_SDA/SCL on SODIMM 194/196 (e.g. RTC on carrier board) */
&i2c1 {
pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c1>;
pinctrl-1 = <&pinctrl_i2c1_gpio>;
sda-gpios = <&gpio1 29 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
scl-gpios = <&gpio1 28 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ status = "okay";
+
+ /* Atmel maxtouch controller */
+ atmel_mxt_ts: touchscreen@4a {
+ compatible = "atmel,maxtouch";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_atmel_conn>;
+ reg = <0x4a>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <4 IRQ_TYPE_EDGE_FALLING>; /* SODIMM 107 / INT */
+ reset-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>; /* SODIMM 106 / RST */
+ status = "disabled";
+ };
};
+ /*
+ * PWR_I2C: power I2C to audio codec, PMIC, temperature sensor and
+ * touch screen controller
+ */
&i2c2 {
+ /* Use low frequency to compensate for the high pull-up values. */
+ clock-frequency = <40000>;
pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c2>;
pinctrl-1 = <&pinctrl_i2c2_gpio>;
scl-gpios = <&gpio1 30 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
status = "okay";
- ad7879@2c {
+ ad7879_ts: touchscreen@2c {
compatible = "adi,ad7879-1";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_snvs_ad7879_int>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_lcdif_dat
&pinctrl_lcdif_ctrl>;
+
+ port {
+ lcdif_out: endpoint {
+ remote-endpoint = <&lcd_panel_in>;
+ };
+ };
};
+ /* PWM <A> */
&pwm4 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm4>;
};
+ /* PWM <B> */
&pwm5 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm5>;
};
+ /* PWM <C> */
&pwm6 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm6>;
};
+ /* PWM <D> */
&pwm7 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm7>;
status = "disabled";
};
+ /* Colibri UART_A */
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1 &pinctrl_uart1_ctrl1>;
fsl,dte-mode;
};
+ /* Colibri UART_B */
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart2>;
fsl,dte-mode;
};
+ /* Colibri UART_C */
&uart5 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart5>;
fsl,dte-mode;
};
+ /* Colibri USBC */
&usbotg1 {
dr_mode = "otg";
srp-disable;
adp-disable;
};
+ /* Colibri USBH */
&usbotg2 {
dr_mode = "host";
};
+ /* Colibri MMC/SD */
&usdhc1 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+ pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_snvs_usdhc1_cd>;
+ pinctrl-1 = <&pinctrl_usdhc1_100mhz &pinctrl_snvs_usdhc1_cd>;
+ pinctrl-2 = <&pinctrl_usdhc1_200mhz &pinctrl_snvs_usdhc1_cd>;
+ pinctrl-3 = <&pinctrl_usdhc1 &pinctrl_snvs_usdhc1_cd_sleep>;
assigned-clocks = <&clks IMX6UL_CLK_USDHC1_SEL>, <&clks IMX6UL_CLK_USDHC1>;
assigned-clock-parents = <&clks IMX6UL_CLK_PLL2_PFD2>;
assigned-clock-rates = <0>, <198000000>;
+ bus-width = <4>;
+ cd-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>; /* MMC_CD */
+ disable-wp;
+ keep-power-in-suspend;
+ no-1-8-v;
+ vqmmc-supply = <®_sd1_vqmmc>;
+ wakeup-source;
};
&wdog1 {
};
&iomuxc {
- pinctrl_can_int: canint-grp {
+ pinctrl_adc1: adc1grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO00__GPIO1_IO00 0x3000 /* SODIMM 8 */
+ MX6UL_PAD_GPIO1_IO01__GPIO1_IO01 0x3000 /* SODIMM 6 */
+ MX6UL_PAD_GPIO1_IO08__GPIO1_IO08 0x3000 /* SODIMM 4 */
+ MX6UL_PAD_GPIO1_IO09__GPIO1_IO09 0x3000 /* SODIMM 2 */
+ >;
+ };
+
+ pinctrl_atmel_adap: atmeladapgrp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_DQS__GPIO4_IO16 0xb0a0 /* SODIMM 28 */
+ MX6UL_PAD_ENET1_TX_EN__GPIO2_IO05 0xb0a0 /* SODIMM 30 */
+ >;
+ };
+
+ pinctrl_atmel_conn: atmelconngrp {
+ fsl,pins = <
+ MX6UL_PAD_JTAG_MOD__GPIO1_IO10 0xb0a0 /* SODIMM 106 */
+ MX6ULL_PAD_SNVS_TAMPER4__GPIO5_IO04 0xb0a0 /* SODIMM 107 */
+ >;
+ };
+
+ pinctrl_can_int: canintgrp {
fsl,pins = <
MX6UL_PAD_ENET1_TX_DATA1__GPIO2_IO04 0x13010 /* SODIMM 73 */
>;
};
- pinctrl_enet2: enet2-grp {
+ pinctrl_enet2: enet2grp {
fsl,pins = <
MX6UL_PAD_GPIO1_IO06__ENET2_MDIO 0x1b0b0
MX6UL_PAD_GPIO1_IO07__ENET2_MDC 0x1b0b0
>;
};
- pinctrl_enet2_sleep: enet2sleepgrp {
+ pinctrl_enet2_sleep: enet2-sleepgrp {
fsl,pins = <
MX6UL_PAD_GPIO1_IO06__GPIO1_IO06 0x0
MX6UL_PAD_GPIO1_IO07__GPIO1_IO07 0x0
>;
};
- pinctrl_ecspi1_cs: ecspi1-cs-grp {
+ pinctrl_ecspi1_cs: ecspi1csgrp {
fsl,pins = <
MX6UL_PAD_LCD_DATA21__GPIO3_IO26 0x70a0 /* SODIMM 86 */
>;
};
- pinctrl_ecspi1: ecspi1-grp {
+ pinctrl_ecspi1: ecspi1grp {
fsl,pins = <
MX6UL_PAD_LCD_DATA20__ECSPI1_SCLK 0x000a0 /* SODIMM 88 */
MX6UL_PAD_LCD_DATA22__ECSPI1_MOSI 0x000a0 /* SODIMM 92 */
>;
};
- pinctrl_flexcan1: flexcan1-grp {
+ pinctrl_flexcan1: flexcan1grp {
fsl,pins = <
MX6UL_PAD_ENET1_RX_DATA0__FLEXCAN1_TX 0x1b020
MX6UL_PAD_ENET1_RX_DATA1__FLEXCAN1_RX 0x1b020
>;
};
- pinctrl_flexcan2: flexcan2-grp {
+ pinctrl_flexcan2: flexcan2grp {
fsl,pins = <
MX6UL_PAD_ENET1_TX_DATA0__FLEXCAN2_RX 0x1b020
MX6UL_PAD_ENET1_RX_EN__FLEXCAN2_TX 0x1b020
>;
};
- pinctrl_gpio_bl_on: gpio-bl-on-grp {
+ pinctrl_gpio_bl_on: gpioblongrp {
fsl,pins = <
MX6UL_PAD_JTAG_TMS__GPIO1_IO11 0x30a0 /* SODIMM 71 */
>;
};
- pinctrl_gpio1: gpio1-grp {
+ pinctrl_gpio1: gpio1grp {
fsl,pins = <
MX6UL_PAD_UART3_RX_DATA__GPIO1_IO25 0x10b0 /* SODIMM 77 */
MX6UL_PAD_JTAG_TCK__GPIO1_IO14 0x70a0 /* SODIMM 99 */
>;
};
- pinctrl_gpio2: gpio2-grp { /* Camera */
+ pinctrl_gpio2: gpio2grp { /* Camera */
fsl,pins = <
MX6UL_PAD_CSI_DATA04__GPIO4_IO25 0x10b0 /* SODIMM 69 */
MX6UL_PAD_CSI_MCLK__GPIO4_IO17 0x10b0 /* SODIMM 75 */
>;
};
- pinctrl_gpio3: gpio3-grp { /* CAN2 */
+ pinctrl_gpio3: gpio3grp { /* CAN2 */
fsl,pins = <
MX6UL_PAD_ENET1_RX_EN__GPIO2_IO02 0x10b0 /* SODIMM 178 */
MX6UL_PAD_ENET1_TX_DATA0__GPIO2_IO03 0x10b0 /* SODIMM 188 */
>;
};
- pinctrl_gpio4: gpio4-grp {
+ pinctrl_gpio4: gpio4grp {
fsl,pins = <
MX6UL_PAD_CSI_DATA07__GPIO4_IO28 0x10b0 /* SODIMM 65 */
>;
};
- pinctrl_gpio5: gpio5-grp { /* ATMEL MXT TOUCH */
- fsl,pins = <
- MX6UL_PAD_JTAG_MOD__GPIO1_IO10 0xb0a0 /* SODIMM 106 */
- >;
- };
-
- pinctrl_gpio6: gpio6-grp { /* Wifi pins */
+ pinctrl_gpio6: gpio6grp { /* Wifi pins */
fsl,pins = <
MX6UL_PAD_GPIO1_IO03__GPIO1_IO03 0x10b0 /* SODIMM 89 */
MX6UL_PAD_CSI_DATA02__GPIO4_IO23 0x10b0 /* SODIMM 79 */
>;
};
- pinctrl_gpio7: gpio7-grp { /* CAN1 */
+ pinctrl_gpio7: gpio7grp { /* CAN1 */
fsl,pins = <
MX6UL_PAD_ENET1_RX_DATA0__GPIO2_IO00 0xb0b0/* SODIMM 55 */
MX6UL_PAD_ENET1_RX_DATA1__GPIO2_IO01 0xb0b0 /* SODIMM 63 */
/*
* With an eMMC instead of a raw NAND device the following pins
- * are available at SODIMM pins
+ * are available at SODIMM pins.
*/
- pinctrl_gpmi_gpio: gpmi-gpio-grp {
+ pinctrl_gpmi_gpio: gpmigpiogrp {
fsl,pins = <
MX6UL_PAD_NAND_ALE__GPIO4_IO10 0x10b0 /* SODIMM 140 */
MX6UL_PAD_NAND_CE0_B__GPIO4_IO13 0x10b0 /* SODIMM 144 */
>;
};
- pinctrl_gpmi_nand: gpmi-nand-grp {
+ pinctrl_gpmi_nand: gpminandgrp {
fsl,pins = <
MX6UL_PAD_NAND_DATA00__RAWNAND_DATA00 0x100a9
MX6UL_PAD_NAND_DATA01__RAWNAND_DATA01 0x100a9
>;
};
- pinctrl_i2c1: i2c1-grp {
+ pinctrl_i2c1: i2c1grp {
fsl,pins = <
MX6UL_PAD_UART4_TX_DATA__I2C1_SCL 0x4001b8b0 /* SODIMM 196 */
MX6UL_PAD_UART4_RX_DATA__I2C1_SDA 0x4001b8b0 /* SODIMM 194 */
>;
};
- pinctrl_i2c1_gpio: i2c1-gpio-grp {
+ pinctrl_i2c1_gpio: i2c1-gpiogrp {
fsl,pins = <
MX6UL_PAD_UART4_TX_DATA__GPIO1_IO28 0x4001b8b0 /* SODIMM 196 */
MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29 0x4001b8b0 /* SODIMM 194 */
>;
};
- pinctrl_i2c2: i2c2-grp {
+ pinctrl_i2c2: i2c2grp {
fsl,pins = <
- MX6UL_PAD_UART5_TX_DATA__I2C2_SCL 0x4001b8b0
- MX6UL_PAD_UART5_RX_DATA__I2C2_SDA 0x4001b8b0
+ MX6UL_PAD_UART5_TX_DATA__I2C2_SCL 0x4001f8b0
+ MX6UL_PAD_UART5_RX_DATA__I2C2_SDA 0x4001f8b0
>;
};
- pinctrl_i2c2_gpio: i2c2-gpio-grp {
+ pinctrl_i2c2_gpio: i2c2-gpiogrp {
fsl,pins = <
- MX6UL_PAD_UART5_TX_DATA__GPIO1_IO30 0x4001b8b0
- MX6UL_PAD_UART5_RX_DATA__GPIO1_IO31 0x4001b8b0
+ MX6UL_PAD_UART5_TX_DATA__GPIO1_IO30 0x4001f8b0
+ MX6UL_PAD_UART5_RX_DATA__GPIO1_IO31 0x4001f8b0
>;
};
- pinctrl_lcdif_dat: lcdif-dat-grp {
+ pinctrl_lcdif_dat: lcdifdatgrp {
fsl,pins = <
MX6UL_PAD_LCD_DATA00__LCDIF_DATA00 0x00079 /* SODIMM 76 */
MX6UL_PAD_LCD_DATA01__LCDIF_DATA01 0x00079 /* SODIMM 70 */
>;
};
- pinctrl_lcdif_ctrl: lcdif-ctrl-grp {
+ pinctrl_lcdif_ctrl: lcdifctrlgrp {
fsl,pins = <
MX6UL_PAD_LCD_CLK__LCDIF_CLK 0x00079 /* SODIMM 56 */
MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE 0x00079 /* SODIMM 44 */
>;
};
- pinctrl_pwm4: pwm4-grp {
+ pinctrl_pwm4: pwm4grp {
fsl,pins = <
MX6UL_PAD_NAND_WP_B__PWM4_OUT 0x00079 /* SODIMM 59 */
>;
};
- pinctrl_pwm5: pwm5-grp {
+ pinctrl_pwm5: pwm5grp {
fsl,pins = <
MX6UL_PAD_NAND_DQS__PWM5_OUT 0x00079 /* SODIMM 28 */
>;
};
- pinctrl_pwm6: pwm6-grp {
+ pinctrl_pwm6: pwm6grp {
fsl,pins = <
MX6UL_PAD_ENET1_TX_EN__PWM6_OUT 0x00079 /* SODIMM 30 */
>;
};
- pinctrl_pwm7: pwm7-grp {
+ pinctrl_pwm7: pwm7grp {
fsl,pins = <
MX6UL_PAD_ENET1_TX_CLK__PWM7_OUT 0x00079 /* SODIMM 67 */
>;
};
- pinctrl_uart1: uart1-grp {
+ pinctrl_uart1: uart1grp {
fsl,pins = <
MX6UL_PAD_UART1_TX_DATA__UART1_DTE_RX 0x1b0b1 /* SODIMM 33 */
MX6UL_PAD_UART1_RX_DATA__UART1_DTE_TX 0x1b0b1 /* SODIMM 35 */
>;
};
- pinctrl_uart1_ctrl1: uart1-ctrl1-grp { /* Additional DTR, DCD */
+ pinctrl_uart1_ctrl1: uart1ctrl1grp { /* Additional DTR, DCD */
fsl,pins = <
- MX6UL_PAD_JTAG_TDI__GPIO1_IO13 0x70a0 /* SODIMM 31 */
- MX6UL_PAD_LCD_DATA18__GPIO3_IO23 0x10b0 /* SODIMM 29 */
- MX6UL_PAD_JTAG_TDO__GPIO1_IO12 0x90b1 /* SODIMM 23 */
- MX6UL_PAD_LCD_DATA19__GPIO3_IO24 0x10b0 /* SODIMM 37 */
+ MX6UL_PAD_JTAG_TDI__GPIO1_IO13 0x70a0 /* SODIMM 31 / DCD */
+ MX6UL_PAD_LCD_DATA18__GPIO3_IO23 0x10b0 /* SODIMM 29 / DSR */
+ MX6UL_PAD_JTAG_TDO__GPIO1_IO12 0x90b1 /* SODIMM 23 / DTR */
+ MX6UL_PAD_LCD_DATA19__GPIO3_IO24 0x10b0 /* SODIMM 37 / RI */
>;
};
- pinctrl_uart2: uart2-grp {
+ pinctrl_uart2: uart2grp {
fsl,pins = <
MX6UL_PAD_UART2_TX_DATA__UART2_DTE_RX 0x1b0b1 /* SODIMM 36 */
MX6UL_PAD_UART2_RX_DATA__UART2_DTE_TX 0x1b0b1 /* SODIMM 38 */
MX6UL_PAD_UART2_RTS_B__UART2_DTE_CTS 0x1b0b1 /* SODIMM 34 */
>;
};
- pinctrl_uart5: uart5-grp {
+ pinctrl_uart5: uart5grp {
fsl,pins = <
MX6UL_PAD_GPIO1_IO04__UART5_DTE_RX 0x1b0b1 /* SODIMM 19 */
MX6UL_PAD_GPIO1_IO05__UART5_DTE_TX 0x1b0b1 /* SODIMM 21 */
>;
};
- pinctrl_usbh_reg: gpio-usbh-reg {
+ pinctrl_usbh_reg: usbhreggrp {
fsl,pins = <
- MX6UL_PAD_GPIO1_IO02__GPIO1_IO02 0x10b0 /* SODIMM 129 */
+ MX6UL_PAD_GPIO1_IO02__GPIO1_IO02 0x10b0 /* SODIMM 129 / USBH_PEN */
>;
};
- pinctrl_usdhc1: usdhc1-grp {
+ pinctrl_usdhc1: usdhc1grp {
fsl,pins = <
- MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x17059 /* SODIMM 47 */
- MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x10059 /* SODIMM 190 */
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x10059 /* SODIMM 47 */
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x17059 /* SODIMM 190 */
MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x17059 /* SODIMM 192 */
MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x17059 /* SODIMM 49 */
MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x17059 /* SODIMM 51 */
>;
};
- pinctrl_usdhc1_100mhz: usdhc1-100mhz-grp {
+ pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
fsl,pins = <
- MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x170b9
- MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x100b9
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x100b9
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x170b9
MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170b9
MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170b9
MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170b9
>;
};
- pinctrl_usdhc1_200mhz: usdhc1-200mhz-grp {
+ pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
fsl,pins = <
- MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x170f9
- MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x100f9
- MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170b9
- MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170b9
- MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170b9
- MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170b9
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x100f9
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x170f9
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170f9
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170f9
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170f9
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170f9
>;
};
- pinctrl_usdhc2: usdhc2-grp {
+ pinctrl_usdhc2: usdhc2grp {
fsl,pins = <
MX6UL_PAD_CSI_DATA00__USDHC2_DATA0 0x17069
MX6UL_PAD_CSI_DATA01__USDHC2_DATA1 0x17069
MX6UL_PAD_CSI_DATA02__USDHC2_DATA2 0x17069
MX6UL_PAD_CSI_DATA03__USDHC2_DATA3 0x17069
MX6UL_PAD_CSI_HSYNC__USDHC2_CMD 0x17069
- MX6UL_PAD_CSI_VSYNC__USDHC2_CLK 0x17069
+ MX6UL_PAD_CSI_VSYNC__USDHC2_CLK 0x10069
MX6UL_PAD_GPIO1_IO03__OSC32K_32K_OUT 0x10
>;
>;
};
- pinctrl_wdog: wdog-grp {
+ pinctrl_wdog: wdoggrp {
fsl,pins = <
MX6UL_PAD_LCD_RESET__WDOG1_WDOG_ANY 0x30b0
>;
};
&iomuxc_snvs {
- pinctrl_snvs_gpio1: snvs-gpio1-grp {
+ pinctrl_snvs_gpio1: snvsgpio1grp {
fsl,pins = <
MX6ULL_PAD_SNVS_TAMPER6__GPIO5_IO06 0x110a0 /* SODIMM 93 */
MX6ULL_PAD_SNVS_TAMPER3__GPIO5_IO03 0x110a0 /* SODIMM 95 */
MX6ULL_PAD_BOOT_MODE0__GPIO5_IO10 0x1b0a0 /* SODIMM 105 */
- MX6ULL_PAD_SNVS_TAMPER5__GPIO5_IO05 0x0b0a0 /* SODIMM 131 */
+ MX6ULL_PAD_SNVS_TAMPER5__GPIO5_IO05 0x0b0a0 /* SODIMM 131 / USBH_OC */
MX6ULL_PAD_SNVS_TAMPER8__GPIO5_IO08 0x110a0 /* SODIMM 138 */
>;
};
- pinctrl_snvs_gpio2: snvs-gpio2-grp { /* ATMEL MXT TOUCH */
- fsl,pins = <
- MX6ULL_PAD_SNVS_TAMPER4__GPIO5_IO04 0xb0a0 /* SODIMM 107 */
- >;
- };
-
- pinctrl_snvs_gpio3: snvs-gpio3-grp { /* Wifi pins */
+ pinctrl_snvs_gpio3: snvsgpio3grp { /* Wifi pins */
fsl,pins = <
MX6ULL_PAD_BOOT_MODE1__GPIO5_IO11 0x130a0 /* SODIMM 127 */
>;
};
- pinctrl_snvs_ad7879_int: snvs-ad7879-int-grp { /* TOUCH Interrupt */
+ pinctrl_snvs_ad7879_int: snvsad7879intgrp { /* TOUCH Interrupt */
fsl,pins = <
MX6ULL_PAD_SNVS_TAMPER7__GPIO5_IO07 0x100b0
>;
};
- pinctrl_snvs_reg_sd: snvs-reg-sd-grp {
+ pinctrl_snvs_reg_sd: snvsregsdgrp {
fsl,pins = <
MX6ULL_PAD_SNVS_TAMPER9__GPIO5_IO09 0x400100b0
>;
};
- pinctrl_snvs_usbc_det: snvs-usbc-det-grp {
+ pinctrl_snvs_usbc_det: snvsusbcdetgrp {
fsl,pins = <
MX6ULL_PAD_SNVS_TAMPER2__GPIO5_IO02 0x130b0
>;
};
- pinctrl_snvs_gpiokeys: snvs-gpiokeys-grp {
+ pinctrl_snvs_gpiokeys: snvsgpiokeysgrp {
fsl,pins = <
- MX6ULL_PAD_SNVS_TAMPER1__GPIO5_IO01 0x130a0 /* SODIMM 45 */
+ MX6ULL_PAD_SNVS_TAMPER1__GPIO5_IO01 0x130a0 /* SODIMM 45 / WAKE_UP */
>;
};
- pinctrl_snvs_usdhc1_cd: snvs-usdhc1-cd-grp {
+ pinctrl_snvs_usdhc1_cd: snvsusdhc1cdgrp {
fsl,pins = <
- MX6ULL_PAD_SNVS_TAMPER0__GPIO5_IO00 0x1b0a0 /* SODIMM 43 */
+ MX6ULL_PAD_SNVS_TAMPER0__GPIO5_IO00 0x1b0a0 /* SODIMM 43 / MMC_CD */
>;
};
- pinctrl_snvs_usdhc1_sleep_cd: snvs-usdhc1-cd-grp-slp {
+ pinctrl_snvs_usdhc1_cd_sleep: snvsusdhc1cd-sleepgrp {
fsl,pins = <
MX6ULL_PAD_SNVS_TAMPER0__GPIO5_IO00 0x0
>;
};
- pinctrl_snvs_wifi_pdn: snvs-wifi-pdn-grp {
+ pinctrl_snvs_wifi_pdn: snvswifipdngrp {
fsl,pins = <
MX6ULL_PAD_BOOT_MODE1__GPIO5_IO11 0x130a0
>;
/* HS USB Host PHY on PORT 1 */
hsusb2_phy: hsusb2_phy {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hsusb2_reset_pin>;
compatible = "usb-nop-xceiv";
reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; /* gpio_4 */
#phy-cells = <0>;
};
&usbhshost {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hsusb2_pins>;
port2-mode = "ehci-phy";
};
phys = <0 &hsusb2_phy>;
};
-
&omap3_pmx_core {
- pinctrl-names = "default";
- pinctrl-0 = <&hsusb2_pins>;
mmc3_pins: pinmux_mm3_pins {
pinctrl-single,pins = <
};
&omap3_pmx_wkup {
- pinctrl-names = "default";
- pinctrl-0 = <&hsusb2_reset_pin>;
+
hsusb2_reset_pin: pinmux_hsusb1_reset_pin {
pinctrl-single,pins = <
OMAP3_WKUP_IOPAD(0x2a0e, PIN_OUTPUT | MUX_MODE4) /* sys_boot2.gpio_4 */
};
};
-&omap3_pmx_core2 {
- pinctrl-names = "default";
- pinctrl-0 = <&hsusb2_2_pins>;
- hsusb2_2_pins: pinmux_hsusb2_2_pins {
- pinctrl-single,pins = <
- OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */
- OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */
- OMAP3630_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */
- OMAP3630_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */
- OMAP3630_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */
- OMAP3630_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */
- >;
- };
-};
-
&uart2 {
interrupts-extended = <&intc 73 &omap3_pmx_core OMAP3_UART2_RX>;
pinctrl-names = "default";
};
clocks {
- cxo_board {
+ cxo_board: cxo_board {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <25000000>;
};
- pxo_board {
+ pxo_board: pxo_board {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <25000000>;
};
gcc: clock-controller@900000 {
- compatible = "qcom,gcc-ipq8064";
+ compatible = "qcom,gcc-ipq8064", "syscon";
+ clocks = <&pxo_board>, <&cxo_board>;
+ clock-names = "pxo", "cxo";
reg = <0x00900000 0x4000>;
#clock-cells = <1>;
#reset-cells = <1>;
snps,axi-config = <&stmmac_axi_setup>;
snps,pbl = <32>;
- snps,aal = <1>;
+ snps,aal;
qcom,nss-common = <&nss_common>;
qcom,qsgmii-csr = <&qsgmii_csr>;
snps,axi-config = <&stmmac_axi_setup>;
snps,pbl = <32>;
- snps,aal = <1>;
+ snps,aal;
qcom,nss-common = <&nss_common>;
qcom,qsgmii-csr = <&qsgmii_csr>;
snps,axi-config = <&stmmac_axi_setup>;
snps,pbl = <32>;
- snps,aal = <1>;
+ snps,aal;
qcom,nss-common = <&nss_common>;
qcom,qsgmii-csr = <&qsgmii_csr>;
snps,axi-config = <&stmmac_axi_setup>;
snps,pbl = <32>;
- snps,aal = <1>;
+ snps,aal;
qcom,nss-common = <&nss_common>;
qcom,qsgmii-csr = <&qsgmii_csr>;
regulator-always-on;
};
- sdcc1bam: dma@12402000 {
+ sdcc1bam: dma-controller@12402000 {
compatible = "qcom,bam-v1.3.0";
reg = <0x12402000 0x8000>;
interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
qcom,ee = <0>;
};
- sdcc3bam: dma@12182000 {
+ sdcc3bam: dma-controller@12182000 {
compatible = "qcom,bam-v1.3.0";
reg = <0x12182000 0x8000>;
interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
#size-cells = <0>;
clocks = <&pmc PMC_TYPE_PERIPHERAL 39>;
atmel,fifo-size = <32>;
- dmas = <&dma0 AT91_XDMAC_DT_PERID(7)>,
- <&dma0 AT91_XDMAC_DT_PERID(8)>;
- dma-names = "rx", "tx";
+ dmas = <&dma0 AT91_XDMAC_DT_PERID(8)>,
+ <&dma0 AT91_XDMAC_DT_PERID(7)>;
+ dma-names = "tx", "rx";
status = "disabled";
};
};
#size-cells = <0>;
clocks = <&pmc PMC_TYPE_PERIPHERAL 46>;
atmel,fifo-size = <32>;
- dmas = <&dma0 AT91_XDMAC_DT_PERID(21)>,
- <&dma0 AT91_XDMAC_DT_PERID(22)>;
- dma-names = "rx", "tx";
+ dmas = <&dma0 AT91_XDMAC_DT_PERID(22)>,
+ <&dma0 AT91_XDMAC_DT_PERID(21)>;
+ dma-names = "tx", "rx";
status = "disabled";
};
};
#size-cells = <0>;
clocks = <&pmc PMC_TYPE_PERIPHERAL 47>;
atmel,fifo-size = <32>;
- dmas = <&dma0 AT91_XDMAC_DT_PERID(23)>,
- <&dma0 AT91_XDMAC_DT_PERID(24)>;
- dma-names = "rx", "tx";
+ dmas = <&dma0 AT91_XDMAC_DT_PERID(24)>,
+ <&dma0 AT91_XDMAC_DT_PERID(23)>;
+ dma-names = "tx", "rx";
status = "disabled";
};
};
#interrupt-cells = <3>;
#address-cells = <0>;
interrupt-controller;
- interrupt-parent;
reg = <0xe8c11000 0x1000>,
<0xe8c12000 0x2000>;
};
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/gpio/gpio.h>
/ {
cpus {
cpu0: cpu@0 {
device_type = "cpu";
- compatible = "arm,cortex-a35","arm,armv8";
+ compatible = "arm,cortex-a35";
reg = <0x0 0x0>;
enable-method = "psci";
};
cpu1: cpu@1 {
device_type = "cpu";
- compatible = "arm,cortex-a35","arm,armv8";
+ compatible = "arm,cortex-a35";
reg = <0x0 0x1>;
enable-method = "psci";
};
cpu2: cpu@2 {
device_type = "cpu";
- compatible = "arm,cortex-a35","arm,armv8";
+ compatible = "arm,cortex-a35";
reg = <0x0 0x2>;
enable-method = "psci";
};
cpu3: cpu@3 {
device_type = "cpu";
- compatible = "arm,cortex-a35","arm,armv8";
+ compatible = "arm,cortex-a35";
reg = <0x0 0x3>;
enable-method = "psci";
};
#clock-cells = <0>;
};
+ pwrc: power-controller {
+ compatible = "amlogic,meson-s4-pwrc";
+ #power-domain-cells = <1>;
+ status = "okay";
+ };
+
soc {
compatible = "simple-bus";
#address-cells = <2>;
#size-cells = <2>;
ranges = <0x0 0x0 0x0 0xfe000000 0x0 0x480000>;
+ periphs_pinctrl: pinctrl@4000 {
+ compatible = "amlogic,meson-s4-periphs-pinctrl";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ gpio: bank@4000 {
+ reg = <0x0 0x4000 0x0 0x004c>,
+ <0x0 0x40c0 0x0 0x0220>;
+ reg-names = "mux", "gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&periphs_pinctrl 0 0 82>;
+ };
+ };
+
+ gpio_intc: interrupt-controller@4080 {
+ compatible = "amlogic,meson-s4-gpio-intc",
+ "amlogic,meson-gpio-intc";
+ reg = <0x0 0x4080 0x0 0x20>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ amlogic,channel-interrupts =
+ <10 11 12 13 14 15 16 17 18 19 20 21>;
+ };
+
uart_B: serial@7a000 {
compatible = "amlogic,meson-s4-uart",
"amlogic,meson-ao-uart";
fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_INPUT>;
fsl,clkreq-unsupported;
clocks = <&pcie0_refclk>;
+ clock-names = "ref";
status = "okay";
};
&usbotg1 {
dr_mode = "otg";
+ over-current-active-low;
vbus-supply = <®_usb_otg1_vbus>;
status = "okay";
};
&usbotg2 {
dr_mode = "host";
+ disable-over-current;
status = "okay";
};
fsl,pins = <
MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0xd6
MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0xd6
- MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0xd6
+ MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO 0xd6
MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0xd6
>;
};
fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_INPUT>;
fsl,clkreq-unsupported;
clocks = <&pcie0_refclk>;
+ clock-names = "ref";
status = "okay";
};
&usbotg1 {
dr_mode = "otg";
+ over-current-active-low;
vbus-supply = <®_usb_otg1_vbus>;
status = "okay";
};
&usbotg2 {
dr_mode = "host";
+ disable-over-current;
vbus-supply = <®_usb_otg2_vbus>;
status = "okay";
};
fsl,pins = <
MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0xd6
MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0xd6
- MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0xd6
+ MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO 0xd6
MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0xd6
>;
};
fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_INPUT>;
fsl,clkreq-unsupported;
clocks = <&pcie0_refclk>;
+ clock-names = "ref";
status = "okay";
};
pinctrl-0 = <&pinctrl_uart3>, <&pinctrl_bten>;
cts-gpios = <&gpio5 8 GPIO_ACTIVE_LOW>;
rts-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+ uart-has-rtscts;
status = "okay";
bluetooth {
&usbotg1 {
dr_mode = "otg";
+ over-current-active-low;
vbus-supply = <®_usb_otg1_vbus>;
status = "okay";
};
&usbotg2 {
dr_mode = "host";
+ disable-over-current;
vbus-supply = <®_usb_otg2_vbus>;
status = "okay";
};
fsl,pins = <
MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0xd6
MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0xd6
- MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0xd6
+ MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO 0xd6
MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0xd6
>;
};
ranges;
sai2: sai@30020000 {
- compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai";
+ compatible = "fsl,imx8mn-sai", "fsl,imx8mq-sai";
reg = <0x30020000 0x10000>;
interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clk IMX8MN_CLK_SAI2_IPG>,
};
sai3: sai@30030000 {
- compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai";
+ compatible = "fsl,imx8mn-sai", "fsl,imx8mq-sai";
reg = <0x30030000 0x10000>;
interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clk IMX8MN_CLK_SAI3_IPG>,
};
sai5: sai@30050000 {
- compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai";
+ compatible = "fsl,imx8mn-sai", "fsl,imx8mq-sai";
reg = <0x30050000 0x10000>;
interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clk IMX8MN_CLK_SAI5_IPG>,
};
sai6: sai@30060000 {
- compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai";
+ compatible = "fsl,imx8mn-sai", "fsl,imx8mq-sai";
reg = <0x30060000 0x10000>;
interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clk IMX8MN_CLK_SAI6_IPG>,
};
sai7: sai@300b0000 {
- compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai";
+ compatible = "fsl,imx8mn-sai", "fsl,imx8mq-sai";
reg = <0x300b0000 0x10000>;
interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clk IMX8MN_CLK_SAI7_IPG>,
clocks = <&clk IMX8MN_CLK_PWM1_ROOT>,
<&clk IMX8MN_CLK_PWM1_ROOT>;
clock-names = "ipg", "per";
- #pwm-cells = <2>;
+ #pwm-cells = <3>;
status = "disabled";
};
clocks = <&clk IMX8MN_CLK_PWM2_ROOT>,
<&clk IMX8MN_CLK_PWM2_ROOT>;
clock-names = "ipg", "per";
- #pwm-cells = <2>;
+ #pwm-cells = <3>;
status = "disabled";
};
clocks = <&clk IMX8MN_CLK_PWM3_ROOT>,
<&clk IMX8MN_CLK_PWM3_ROOT>;
clock-names = "ipg", "per";
- #pwm-cells = <2>;
+ #pwm-cells = <3>;
status = "disabled";
};
clocks = <&clk IMX8MN_CLK_PWM4_ROOT>,
<&clk IMX8MN_CLK_PWM4_ROOT>;
clock-names = "ipg", "per";
- #pwm-cells = <2>;
+ #pwm-cells = <3>;
status = "disabled";
};
};
usdhc1: mmc@30b40000 {
- compatible = "fsl,imx8mn-usdhc", "fsl,imx7d-usdhc";
+ compatible = "fsl,imx8mn-usdhc", "fsl,imx8mm-usdhc", "fsl,imx7d-usdhc";
reg = <0x30b40000 0x10000>;
interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clk IMX8MN_CLK_IPG_ROOT>,
};
usdhc2: mmc@30b50000 {
- compatible = "fsl,imx8mn-usdhc", "fsl,imx7d-usdhc";
+ compatible = "fsl,imx8mn-usdhc", "fsl,imx8mm-usdhc", "fsl,imx7d-usdhc";
reg = <0x30b50000 0x10000>;
interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clk IMX8MN_CLK_IPG_ROOT>,
};
usdhc3: mmc@30b60000 {
- compatible = "fsl,imx8mn-usdhc", "fsl,imx7d-usdhc";
+ compatible = "fsl,imx8mn-usdhc", "fsl,imx8mm-usdhc", "fsl,imx7d-usdhc";
reg = <0x30b60000 0x10000>;
interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clk IMX8MN_CLK_IPG_ROOT>,
assigned-clock-parents = <&tbg 1>;
assigned-clock-rates = <20000000>;
- spi-flash@0 {
+ flash@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "jedec,spi-nor";
/* switch nodes are enabled by U-Boot if modules are present */
switch0@10 {
compatible = "marvell,mv88e6190";
- reg = <0x10 0>;
+ reg = <0x10>;
dsa,member = <0 0>;
interrupt-parent = <&moxtet>;
interrupts = <MOXTET_IRQ_PERIDOT(0)>;
switch0@2 {
compatible = "marvell,mv88e6085";
- reg = <0x2 0>;
+ reg = <0x2>;
dsa,member = <0 0>;
interrupt-parent = <&moxtet>;
interrupts = <MOXTET_IRQ_TOPAZ>;
switch1@11 {
compatible = "marvell,mv88e6190";
- reg = <0x11 0>;
+ reg = <0x11>;
dsa,member = <0 1>;
interrupt-parent = <&moxtet>;
interrupts = <MOXTET_IRQ_PERIDOT(1)>;
switch1@2 {
compatible = "marvell,mv88e6085";
- reg = <0x2 0>;
+ reg = <0x2>;
dsa,member = <0 1>;
interrupt-parent = <&moxtet>;
interrupts = <MOXTET_IRQ_TOPAZ>;
switch2@12 {
compatible = "marvell,mv88e6190";
- reg = <0x12 0>;
+ reg = <0x12>;
dsa,member = <0 2>;
interrupt-parent = <&moxtet>;
interrupts = <MOXTET_IRQ_PERIDOT(2)>;
switch2@2 {
compatible = "marvell,mv88e6085";
- reg = <0x2 0>;
+ reg = <0x2>;
dsa,member = <0 2>;
interrupt-parent = <&moxtet>;
interrupts = <MOXTET_IRQ_TOPAZ>;
enable-method = "psci";
clock-frequency = <1300000000>;
cci-control-port = <&cci_control2>;
+ next-level-cache = <&L2>;
};
cpu1: cpu@1 {
enable-method = "psci";
clock-frequency = <1300000000>;
cci-control-port = <&cci_control2>;
+ next-level-cache = <&L2>;
+ };
+
+ L2: l2-cache {
+ compatible = "cache";
+ cache-level = <2>;
};
};
};
cci_control2: slave-if@5000 {
- compatible = "arm,cci-400-ctrl-if";
+ compatible = "arm,cci-400-ctrl-if", "syscon";
interface-type = "ace";
reg = <0x5000 0x1000>;
};
status = "disabled";
};
+ snfi: spi@1100d000 {
+ compatible = "mediatek,mt7622-snand";
+ reg = <0 0x1100d000 0 0x1000>;
+ interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&pericfg CLK_PERI_NFI_PD>, <&pericfg CLK_PERI_SNFI_PD>;
+ clock-names = "nfi_clk", "pad_clk";
+ nand-ecc-engine = <&bch>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
bch: ecc@1100e000 {
compatible = "mediatek,mt7622-ecc";
reg = <0 0x1100e000 0 0x1000>;
};
};
+ hifsys: syscon@1af00000 {
+ compatible = "mediatek,mt7622-hifsys", "syscon";
+ reg = <0 0x1af00000 0 0x70>;
+ };
+
ethsys: syscon@1b000000 {
compatible = "mediatek,mt7622-ethsys",
"syscon";
clock-names = "hsdma";
power-domains = <&scpsys MT7622_POWER_DOMAIN_ETHSYS>;
#dma-cells = <1>;
+ dma-requests = <3>;
};
+ pcie_mirror: pcie-mirror@10000400 {
+ compatible = "mediatek,mt7622-pcie-mirror",
+ "syscon";
+ reg = <0 0x10000400 0 0x10>;
+ };
+
+ wed0: wed@1020a000 {
+ compatible = "mediatek,mt7622-wed",
+ "syscon";
+ reg = <0 0x1020a000 0 0x1000>;
+ interrupts = <GIC_SPI 214 IRQ_TYPE_LEVEL_LOW>;
+ };
+
+ wed1: wed@1020b000 {
+ compatible = "mediatek,mt7622-wed",
+ "syscon";
+ reg = <0 0x1020b000 0 0x1000>;
+ interrupts = <GIC_SPI 215 IRQ_TYPE_LEVEL_LOW>;
+ };
+
eth: ethernet@1b100000 {
compatible = "mediatek,mt7622-eth",
"mediatek,mt2701-eth",
power-domains = <&scpsys MT7622_POWER_DOMAIN_ETHSYS>;
mediatek,ethsys = <ðsys>;
mediatek,sgmiisys = <&sgmiisys>;
+ cci-control-port = <&cci_control2>;
+ mediatek,wed = <&wed0>, <&wed1>;
+ mediatek,pcie-mirror = <&pcie_mirror>;
+ mediatek,hifsys = <&hifsys>;
+ dma-coherent;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
#size-cells = <2>;
ranges;
- mba_region: mba@91500000 {
- reg = <0x0 0x91500000 0x0 0x200000>;
+ hyp_mem: memory@85800000 {
+ reg = <0x0 0x85800000 0x0 0x600000>;
no-map;
};
- slpi_region: slpi@90b00000 {
- reg = <0x0 0x90b00000 0x0 0xa00000>;
+ xbl_mem: memory@85e00000 {
+ reg = <0x0 0x85e00000 0x0 0x200000>;
no-map;
};
- venus_region: venus@90400000 {
- reg = <0x0 0x90400000 0x0 0x700000>;
+ smem_mem: smem-mem@86000000 {
+ reg = <0x0 0x86000000 0x0 0x200000>;
no-map;
};
- adsp_region: adsp@8ea00000 {
- reg = <0x0 0x8ea00000 0x0 0x1a00000>;
+ tz_mem: memory@86200000 {
+ reg = <0x0 0x86200000 0x0 0x2600000>;
no-map;
};
- mpss_region: mpss@88800000 {
- reg = <0x0 0x88800000 0x0 0x6200000>;
+ rmtfs_mem: rmtfs {
+ compatible = "qcom,rmtfs-mem";
+
+ size = <0x0 0x200000>;
+ alloc-ranges = <0x0 0xa0000000 0x0 0x2000000>;
no-map;
+
+ qcom,client-id = <1>;
+ qcom,vmid = <15>;
};
- smem_mem: smem-mem@86000000 {
- reg = <0x0 0x86000000 0x0 0x200000>;
+ mpss_mem: mpss@88800000 {
+ reg = <0x0 0x88800000 0x0 0x6200000>;
no-map;
};
- memory@85800000 {
- reg = <0x0 0x85800000 0x0 0x800000>;
+ adsp_mem: adsp@8ea00000 {
+ reg = <0x0 0x8ea00000 0x0 0x1b00000>;
no-map;
};
- memory@86200000 {
- reg = <0x0 0x86200000 0x0 0x2600000>;
+ slpi_mem: slpi@90500000 {
+ reg = <0x0 0x90500000 0x0 0xa00000>;
no-map;
};
- rmtfs@86700000 {
- compatible = "qcom,rmtfs-mem";
-
- size = <0x0 0x200000>;
- alloc-ranges = <0x0 0xa0000000 0x0 0x2000000>;
+ gpu_mem: gpu@90f00000 {
+ compatible = "shared-dma-pool";
+ reg = <0x0 0x90f00000 0x0 0x100000>;
no-map;
+ };
- qcom,client-id = <1>;
- qcom,vmid = <15>;
+ venus_mem: venus@91000000 {
+ reg = <0x0 0x91000000 0x0 0x500000>;
+ no-map;
};
- zap_shader_region: gpu@8f200000 {
- compatible = "shared-dma-pool";
- reg = <0x0 0x90b00000 0x0 0xa00000>;
+ mba_mem: mba@91500000 {
+ reg = <0x0 0x91500000 0x0 0x200000>;
no-map;
};
};
qcom,glink-channels = "rpm_requests";
rpmcc: qcom,rpmcc {
- compatible = "qcom,rpmcc-msm8996";
+ compatible = "qcom,rpmcc-msm8996", "qcom,rpmcc";
#clock-cells = <1>;
};
qcom,local-pid = <0>;
qcom,remote-pid = <2>;
- smp2p_adsp_out: master-kernel {
+ adsp_smp2p_out: master-kernel {
qcom,entry-name = "master-kernel";
#qcom,smem-state-cells = <1>;
};
- smp2p_adsp_in: slave-kernel {
+ adsp_smp2p_in: slave-kernel {
qcom,entry-name = "slave-kernel";
interrupt-controller;
};
};
- smp2p-modem {
+ smp2p-mpss {
compatible = "qcom,smp2p";
qcom,smem = <435>, <428>;
qcom,local-pid = <0>;
qcom,remote-pid = <1>;
- modem_smp2p_out: master-kernel {
+ mpss_smp2p_out: master-kernel {
qcom,entry-name = "master-kernel";
#qcom,smem-state-cells = <1>;
};
- modem_smp2p_in: slave-kernel {
+ mpss_smp2p_in: slave-kernel {
qcom,entry-name = "slave-kernel";
interrupt-controller;
qcom,local-pid = <0>;
qcom,remote-pid = <3>;
- smp2p_slpi_in: slave-kernel {
+ slpi_smp2p_out: master-kernel {
+ qcom,entry-name = "master-kernel";
+ #qcom,smem-state-cells = <1>;
+ };
+
+ slpi_smp2p_in: slave-kernel {
qcom,entry-name = "slave-kernel";
+
interrupt-controller;
#interrupt-cells = <2>;
};
-
- smp2p_slpi_out: master-kernel {
- qcom,entry-name = "master-kernel";
- #qcom,smem-state-cells = <1>;
- };
};
soc: soc {
#thermal-sensor-cells = <1>;
};
- cryptobam: dma@644000 {
+ cryptobam: dma-controller@644000 {
compatible = "qcom,bam-v1.7.0";
reg = <0x00644000 0x24000>;
interrupts = <GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH>;
reg-names = "mdp_phys";
interrupt-parent = <&mdss>;
- interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <0>;
clocks = <&mmcc MDSS_AHB_CLK>,
<&mmcc MDSS_AXI_CLK>,
reg-names = "dsi_ctrl";
interrupt-parent = <&mdss>;
- interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <4>;
clocks = <&mmcc MDSS_MDP_CLK>,
<&mmcc MDSS_BYTE0_CLK>,
"hdcp_physical";
interrupt-parent = <&mdss>;
- interrupts = <8 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <8>;
clocks = <&mmcc MDSS_MDP_CLK>,
<&mmcc MDSS_AHB_CLK>,
};
zap-shader {
- memory-region = <&zap_shader_region>;
+ memory-region = <&gpu_mem>;
};
};
pins = "gpio47", "gpio48";
function = "blsp_i2c3";
drive-strength = <16>;
- bias-disable = <0>;
+ bias-disable;
};
blsp1_i2c3_sleep: blsp1-i2c2-sleep {
pins = "gpio47", "gpio48";
function = "gpio";
drive-strength = <2>;
- bias-disable = <0>;
+ bias-disable;
};
blsp2_uart3_4pins_default: blsp2-uart2-4pins {
ranges;
pcie0: pcie@600000 {
- compatible = "qcom,pcie-msm8996", "snps,dw-pcie";
+ compatible = "qcom,pcie-msm8996";
status = "disabled";
power-domains = <&gcc PCIE0_GDSC>;
bus-range = <0x00 0xff>;
};
pcie1: pcie@608000 {
- compatible = "qcom,pcie-msm8996", "snps,dw-pcie";
+ compatible = "qcom,pcie-msm8996";
power-domains = <&gcc PCIE1_GDSC>;
bus-range = <0x00 0xff>;
num-lanes = <1>;
};
pcie2: pcie@610000 {
- compatible = "qcom,pcie-msm8996", "snps,dw-pcie";
+ compatible = "qcom,pcie-msm8996";
power-domains = <&gcc PCIE2_GDSC>;
bus-range = <0x00 0xff>;
num-lanes = <1>;
};
ufshc: ufshc@624000 {
- compatible = "qcom,ufshc";
+ compatible = "qcom,msm8996-ufshc", "qcom,ufshc",
+ "jedec,ufs-2.0";
reg = <0x00624000 0x2500>;
interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>;
<&venus_smmu 0x2c>,
<&venus_smmu 0x2d>,
<&venus_smmu 0x31>;
- memory-region = <&venus_region>;
+ memory-region = <&venus_mem>;
status = "disabled";
video-decoder {
clock-names = "iface", "bus";
};
+ slpi_pil: remoteproc@1c00000 {
+ compatible = "qcom,msm8996-slpi-pil";
+ reg = <0x01c00000 0x4000>;
+
+ interrupts-extended = <&intc 0 390 IRQ_TYPE_EDGE_RISING>,
+ <&slpi_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+ <&slpi_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+ <&slpi_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+ <&slpi_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "wdog",
+ "fatal",
+ "ready",
+ "handover",
+ "stop-ack";
+
+ clocks = <&xo_board>,
+ <&rpmcc RPM_SMD_AGGR2_NOC_CLK>;
+ clock-names = "xo", "aggre2";
+
+ memory-region = <&slpi_mem>;
+
+ qcom,smem-states = <&slpi_smp2p_out 0>;
+ qcom,smem-state-names = "stop";
+
+ power-domains = <&rpmpd MSM8996_VDDSSCX>;
+ power-domain-names = "ssc_cx";
+
+ status = "disabled";
+
+ smd-edge {
+ interrupts = <GIC_SPI 176 IRQ_TYPE_EDGE_RISING>;
+
+ label = "dsps";
+ mboxes = <&apcs_glb 25>;
+ qcom,smd-edge = <3>;
+ qcom,remote-pid = <3>;
+ };
+ };
+
+ mss_pil: remoteproc@2080000 {
+ compatible = "qcom,msm8996-mss-pil";
+ reg = <0x2080000 0x100>,
+ <0x2180000 0x020>;
+ reg-names = "qdsp6", "rmb";
+
+ interrupts-extended = <&intc 0 448 IRQ_TYPE_EDGE_RISING>,
+ <&mpss_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+ <&mpss_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+ <&mpss_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+ <&mpss_smp2p_in 3 IRQ_TYPE_EDGE_RISING>,
+ <&mpss_smp2p_in 7 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "wdog", "fatal", "ready",
+ "handover", "stop-ack",
+ "shutdown-ack";
+
+ clocks = <&gcc GCC_MSS_CFG_AHB_CLK>,
+ <&gcc GCC_MSS_Q6_BIMC_AXI_CLK>,
+ <&gcc GCC_BOOT_ROM_AHB_CLK>,
+ <&xo_board>,
+ <&gcc GCC_MSS_GPLL0_DIV_CLK>,
+ <&gcc GCC_MSS_SNOC_AXI_CLK>,
+ <&gcc GCC_MSS_MNOC_BIMC_AXI_CLK>,
+ <&rpmcc RPM_SMD_PCNOC_CLK>,
+ <&rpmcc RPM_SMD_QDSS_CLK>;
+ clock-names = "iface", "bus", "mem", "xo", "gpll0_mss",
+ "snoc_axi", "mnoc_axi", "pnoc", "qdss";
+
+ resets = <&gcc GCC_MSS_RESTART>;
+ reset-names = "mss_restart";
+
+ power-domains = <&rpmpd MSM8996_VDDCX>,
+ <&rpmpd MSM8996_VDDMX>;
+ power-domain-names = "cx", "mx";
+
+ qcom,smem-states = <&mpss_smp2p_out 0>;
+ qcom,smem-state-names = "stop";
+
+ qcom,halt-regs = <&tcsr_mutex_regs 0x23000 0x25000 0x24000>;
+
+ status = "disabled";
+
+ mba {
+ memory-region = <&mba_mem>;
+ };
+
+ mpss {
+ memory-region = <&mpss_mem>;
+ };
+
+ smd-edge {
+ interrupts = <GIC_SPI 449 IRQ_TYPE_EDGE_RISING>;
+
+ label = "mpss";
+ mboxes = <&apcs_glb 12>;
+ qcom,smd-edge = <0>;
+ qcom,remote-pid = <1>;
+ };
+ };
+
stm@3002000 {
compatible = "arm,coresight-stm", "arm,primecell";
reg = <0x3002000 0x1000>,
compatible = "qcom,i2c-qup-v2.2.1";
reg = <0x07577000 0x1000>;
interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP1_AHB_CLK>,
- <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>;
- clock-names = "iface", "core";
+ clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&blsp1_i2c3_default>;
pinctrl-1 = <&blsp1_i2c3_sleep>;
compatible = "qcom,i2c-qup-v2.2.1";
reg = <0x075b5000 0x1000>;
interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP2_AHB_CLK>,
- <&gcc GCC_BLSP2_QUP1_I2C_APPS_CLK>;
- clock-names = "iface", "core";
+ clocks = <&gcc GCC_BLSP2_QUP1_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP2_AHB_CLK>;
+ clock-names = "core", "iface";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&blsp2_i2c1_default>;
pinctrl-1 = <&blsp2_i2c1_sleep>;
compatible = "qcom,i2c-qup-v2.2.1";
reg = <0x075b6000 0x1000>;
interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP2_AHB_CLK>,
- <&gcc GCC_BLSP2_QUP2_I2C_APPS_CLK>;
- clock-names = "iface", "core";
+ clocks = <&gcc GCC_BLSP2_QUP2_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP2_AHB_CLK>;
+ clock-names = "core", "iface";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&blsp2_i2c2_default>;
pinctrl-1 = <&blsp2_i2c2_sleep>;
compatible = "qcom,i2c-qup-v2.2.1";
reg = <0x075b7000 0x1000>;
interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP2_AHB_CLK>,
- <&gcc GCC_BLSP2_QUP3_I2C_APPS_CLK>;
- clock-names = "iface", "core";
+ clocks = <&gcc GCC_BLSP2_QUP3_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP2_AHB_CLK>;
+ clock-names = "core", "iface";
clock-frequency = <400000>;
pinctrl-names = "default", "sleep";
pinctrl-0 = <&blsp2_i2c3_default>;
compatible = "qcom,i2c-qup-v2.2.1";
reg = <0x75b9000 0x1000>;
interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP2_AHB_CLK>,
- <&gcc GCC_BLSP2_QUP5_I2C_APPS_CLK>;
- clock-names = "iface", "core";
+ clocks = <&gcc GCC_BLSP2_QUP5_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP2_AHB_CLK>;
+ clock-names = "core", "iface";
pinctrl-names = "default";
pinctrl-0 = <&blsp2_i2c5_default>;
dmas = <&blsp2_dma 20>, <&blsp2_dma 21>;
compatible = "qcom,i2c-qup-v2.2.1";
reg = <0x75ba000 0x1000>;
interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GCC_BLSP2_AHB_CLK>,
- <&gcc GCC_BLSP2_QUP6_I2C_APPS_CLK>;
- clock-names = "iface", "core";
+ clocks = <&gcc GCC_BLSP2_QUP6_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP2_AHB_CLK>;
+ clock-names = "core", "iface";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&blsp2_i2c6_default>;
pinctrl-1 = <&blsp2_i2c6_sleep>;
reg = <0x09300000 0x80000>;
interrupts-extended = <&intc 0 162 IRQ_TYPE_EDGE_RISING>,
- <&smp2p_adsp_in 0 IRQ_TYPE_EDGE_RISING>,
- <&smp2p_adsp_in 1 IRQ_TYPE_EDGE_RISING>,
- <&smp2p_adsp_in 2 IRQ_TYPE_EDGE_RISING>,
- <&smp2p_adsp_in 3 IRQ_TYPE_EDGE_RISING>;
+ <&adsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+ <&adsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+ <&adsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+ <&adsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
interrupt-names = "wdog", "fatal", "ready",
"handover", "stop-ack";
clocks = <&rpmcc RPM_SMD_BB_CLK1>;
clock-names = "xo";
- memory-region = <&adsp_region>;
+ memory-region = <&adsp_mem>;
- qcom,smem-states = <&smp2p_adsp_out 0>;
+ qcom,smem-states = <&adsp_smp2p_out 0>;
qcom,smem-state-names = "stop";
power-domains = <&rpmpd MSM8996_VDDCX>;
* Copyright 2020 Google LLC.
*/
- #include "sc7180.dtsi"
-
- ap_ec_spi: &spi6 {};
- ap_h1_spi: &spi0 {};
-
#include "sc7180-trogdor.dtsi"
#include "sc7180-trogdor-ti-sn65dsi86.dtsi"
};
&alc5682 {
- realtek,dmic-clk-driving-high = "true";
+ realtek,dmic-clk-driving-high;
};
+ &ap_tp_i2c {
+ status = "okay";
+ };
+
&cpu6_alert0 {
temperature = <60000>;
};
#include <dt-bindings/soc/qcom,rpmh-rsc.h>
#include <dt-bindings/sound/qcom,q6afe.h>
#include <dt-bindings/thermal/thermal.h>
+ #include <dt-bindings/clock/qcom,camcc-sm8250.h>
#include <dt-bindings/clock/qcom,videocc-sm8250.h>
/ {
pinctrl-0 = <&rx_swr_active>;
compatible = "qcom,sm8250-lpass-rx-macro";
reg = <0 0x3200000 0 0x1000>;
+ status = "disabled";
clocks = <&q6afecc LPASS_CLK_ID_TX_CORE_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
<&q6afecc LPASS_CLK_ID_TX_CORE_NPL_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
swr1: soundwire-controller@3210000 {
reg = <0 0x3210000 0 0x2000>;
compatible = "qcom,soundwire-v1.5.1";
+ status = "disabled";
interrupts = <GIC_SPI 298 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rxmacro>;
clock-names = "iface";
pinctrl-0 = <&tx_swr_active>;
compatible = "qcom,sm8250-lpass-tx-macro";
reg = <0 0x3220000 0 0x1000>;
+ status = "disabled";
clocks = <&q6afecc LPASS_CLK_ID_TX_CORE_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
<&q6afecc LPASS_CLK_ID_TX_CORE_NPL_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
compatible = "qcom,soundwire-v1.5.1";
interrupts-extended = <&intc GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "core";
+ status = "disabled";
clocks = <&txmacro>;
clock-names = "iface";
#power-domain-cells = <1>;
};
+ cci0: cci@ac4f000 {
+ compatible = "qcom,sm8250-cci";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reg = <0 0x0ac4f000 0 0x1000>;
+ interrupts = <GIC_SPI 460 IRQ_TYPE_EDGE_RISING>;
+ power-domains = <&camcc TITAN_TOP_GDSC>;
+
+ clocks = <&camcc CAM_CC_CAMNOC_AXI_CLK>,
+ <&camcc CAM_CC_SLOW_AHB_CLK_SRC>,
+ <&camcc CAM_CC_CPAS_AHB_CLK>,
+ <&camcc CAM_CC_CCI_0_CLK>,
+ <&camcc CAM_CC_CCI_0_CLK_SRC>;
+ clock-names = "camnoc_axi",
+ "slow_ahb_src",
+ "cpas_ahb",
+ "cci",
+ "cci_src";
+
+ pinctrl-0 = <&cci0_default>;
+ pinctrl-1 = <&cci0_sleep>;
+ pinctrl-names = "default", "sleep";
+
+ status = "disabled";
+
+ cci0_i2c0: i2c-bus@0 {
+ reg = <0>;
+ clock-frequency = <1000000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ cci0_i2c1: i2c-bus@1 {
+ reg = <1>;
+ clock-frequency = <1000000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
+ cci1: cci@ac50000 {
+ compatible = "qcom,sm8250-cci";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reg = <0 0x0ac50000 0 0x1000>;
+ interrupts = <GIC_SPI 271 IRQ_TYPE_EDGE_RISING>;
+ power-domains = <&camcc TITAN_TOP_GDSC>;
+
+ clocks = <&camcc CAM_CC_CAMNOC_AXI_CLK>,
+ <&camcc CAM_CC_SLOW_AHB_CLK_SRC>,
+ <&camcc CAM_CC_CPAS_AHB_CLK>,
+ <&camcc CAM_CC_CCI_1_CLK>,
+ <&camcc CAM_CC_CCI_1_CLK_SRC>;
+ clock-names = "camnoc_axi",
+ "slow_ahb_src",
+ "cpas_ahb",
+ "cci",
+ "cci_src";
+
+ pinctrl-0 = <&cci1_default>;
+ pinctrl-1 = <&cci1_sleep>;
+ pinctrl-names = "default", "sleep";
+
+ status = "disabled";
+
+ cci1_i2c0: i2c-bus@0 {
+ reg = <0>;
+ clock-frequency = <1000000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ cci1_i2c1: i2c-bus@1 {
+ reg = <1>;
+ clock-frequency = <1000000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
+ camss: camss@ac6a000 {
+ compatible = "qcom,sm8250-camss";
+ status = "disabled";
+
+ reg = <0 0xac6a000 0 0x2000>,
+ <0 0xac6c000 0 0x2000>,
+ <0 0xac6e000 0 0x1000>,
+ <0 0xac70000 0 0x1000>,
+ <0 0xac72000 0 0x1000>,
+ <0 0xac74000 0 0x1000>,
+ <0 0xacb4000 0 0xd000>,
+ <0 0xacc3000 0 0xd000>,
+ <0 0xacd9000 0 0x2200>,
+ <0 0xacdb200 0 0x2200>;
+ reg-names = "csiphy0",
+ "csiphy1",
+ "csiphy2",
+ "csiphy3",
+ "csiphy4",
+ "csiphy5",
+ "vfe0",
+ "vfe1",
+ "vfe_lite0",
+ "vfe_lite1";
+
+ interrupts = <GIC_SPI 477 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 478 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 479 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 448 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 464 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 466 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 468 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 465 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 467 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 469 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "csiphy0",
+ "csiphy1",
+ "csiphy2",
+ "csiphy3",
+ "csiphy4",
+ "csiphy5",
+ "csid0",
+ "csid1",
+ "csid2",
+ "csid3",
+ "vfe0",
+ "vfe1",
+ "vfe_lite0",
+ "vfe_lite1";
+
+ power-domains = <&camcc IFE_0_GDSC>,
+ <&camcc IFE_1_GDSC>,
+ <&camcc TITAN_TOP_GDSC>;
+
+ clocks = <&gcc GCC_CAMERA_AHB_CLK>,
+ <&gcc GCC_CAMERA_HF_AXI_CLK>,
+ <&gcc GCC_CAMERA_SF_AXI_CLK>,
+ <&camcc CAM_CC_CAMNOC_AXI_CLK>,
+ <&camcc CAM_CC_CAMNOC_AXI_CLK_SRC>,
+ <&camcc CAM_CC_CORE_AHB_CLK>,
+ <&camcc CAM_CC_CPAS_AHB_CLK>,
+ <&camcc CAM_CC_CSIPHY0_CLK>,
+ <&camcc CAM_CC_CSI0PHYTIMER_CLK>,
+ <&camcc CAM_CC_CSIPHY1_CLK>,
+ <&camcc CAM_CC_CSI1PHYTIMER_CLK>,
+ <&camcc CAM_CC_CSIPHY2_CLK>,
+ <&camcc CAM_CC_CSI2PHYTIMER_CLK>,
+ <&camcc CAM_CC_CSIPHY3_CLK>,
+ <&camcc CAM_CC_CSI3PHYTIMER_CLK>,
+ <&camcc CAM_CC_CSIPHY4_CLK>,
+ <&camcc CAM_CC_CSI4PHYTIMER_CLK>,
+ <&camcc CAM_CC_CSIPHY5_CLK>,
+ <&camcc CAM_CC_CSI5PHYTIMER_CLK>,
+ <&camcc CAM_CC_SLOW_AHB_CLK_SRC>,
+ <&camcc CAM_CC_IFE_0_AHB_CLK>,
+ <&camcc CAM_CC_IFE_0_AXI_CLK>,
+ <&camcc CAM_CC_IFE_0_CLK>,
+ <&camcc CAM_CC_IFE_0_CPHY_RX_CLK>,
+ <&camcc CAM_CC_IFE_0_CSID_CLK>,
+ <&camcc CAM_CC_IFE_0_AREG_CLK>,
+ <&camcc CAM_CC_IFE_1_AHB_CLK>,
+ <&camcc CAM_CC_IFE_1_AXI_CLK>,
+ <&camcc CAM_CC_IFE_1_CLK>,
+ <&camcc CAM_CC_IFE_1_CPHY_RX_CLK>,
+ <&camcc CAM_CC_IFE_1_CSID_CLK>,
+ <&camcc CAM_CC_IFE_1_AREG_CLK>,
+ <&camcc CAM_CC_IFE_LITE_AHB_CLK>,
+ <&camcc CAM_CC_IFE_LITE_AXI_CLK>,
+ <&camcc CAM_CC_IFE_LITE_CLK>,
+ <&camcc CAM_CC_IFE_LITE_CPHY_RX_CLK>,
+ <&camcc CAM_CC_IFE_LITE_CSID_CLK>;
+
+ clock-names = "cam_ahb_clk",
+ "cam_hf_axi",
+ "cam_sf_axi",
+ "camnoc_axi",
+ "camnoc_axi_src",
+ "core_ahb",
+ "cpas_ahb",
+ "csiphy0",
+ "csiphy0_timer",
+ "csiphy1",
+ "csiphy1_timer",
+ "csiphy2",
+ "csiphy2_timer",
+ "csiphy3",
+ "csiphy3_timer",
+ "csiphy4",
+ "csiphy4_timer",
+ "csiphy5",
+ "csiphy5_timer",
+ "slow_ahb_src",
+ "vfe0_ahb",
+ "vfe0_axi",
+ "vfe0",
+ "vfe0_cphy_rx",
+ "vfe0_csid",
+ "vfe0_areg",
+ "vfe1_ahb",
+ "vfe1_axi",
+ "vfe1",
+ "vfe1_cphy_rx",
+ "vfe1_csid",
+ "vfe1_areg",
+ "vfe_lite_ahb",
+ "vfe_lite_axi",
+ "vfe_lite",
+ "vfe_lite_cphy_rx",
+ "vfe_lite_csid";
+
+ iommus = <&apps_smmu 0x800 0x400>,
+ <&apps_smmu 0x801 0x400>,
+ <&apps_smmu 0x840 0x400>,
+ <&apps_smmu 0x841 0x400>,
+ <&apps_smmu 0xc00 0x400>,
+ <&apps_smmu 0xc01 0x400>,
+ <&apps_smmu 0xc40 0x400>,
+ <&apps_smmu 0xc41 0x400>;
+
+ interconnects = <&gem_noc MASTER_AMPSS_M0 &config_noc SLAVE_CAMERA_CFG>,
+ <&mmss_noc MASTER_CAMNOC_HF &mc_virt SLAVE_EBI_CH0>,
+ <&mmss_noc MASTER_CAMNOC_SF &mc_virt SLAVE_EBI_CH0>,
+ <&mmss_noc MASTER_CAMNOC_ICP &mc_virt SLAVE_EBI_CH0>;
+ interconnect-names = "cam_ahb",
+ "cam_hf_0_mnoc",
+ "cam_sf_0_mnoc",
+ "cam_sf_icp_mnoc";
+ };
+
+ camcc: clock-controller@ad00000 {
+ compatible = "qcom,sm8250-camcc";
+ reg = <0 0x0ad00000 0 0x10000>;
+ clocks = <&gcc GCC_CAMERA_AHB_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>,
+ <&rpmhcc RPMH_CXO_CLK_A>,
+ <&sleep_clk>;
+ clock-names = "iface", "bi_tcxo", "bi_tcxo_ao", "sleep_clk";
+ power-domains = <&rpmhpd SM8250_MMCX>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ #power-domain-cells = <1>;
+ };
+
mdss: mdss@ae00000 {
compatible = "qcom,sm8250-mdss";
reg = <0 0x0ae00000 0 0x1000>;
power-domains = <&rpmhpd SM8250_MMCX>;
interrupt-parent = <&mdss>;
- interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <0>;
ports {
#address-cells = <1>;
reg-names = "dsi_ctrl";
interrupt-parent = <&mdss>;
- interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <4>;
clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
<&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
reg-names = "dsi_ctrl";
interrupt-parent = <&mdss>;
- interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <5>;
clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK>,
<&dispcc DISP_CC_MDSS_BYTE1_INTF_CLK>,
gpio-ranges = <&tlmm 0 0 181>;
wakeup-parent = <&pdc>;
+ cci0_default: cci0-default {
+ cci0_i2c0_default: cci0-i2c0-default {
+ /* SDA, SCL */
+ pins = "gpio101", "gpio102";
+ function = "cci_i2c";
+
+ bias-pull-up;
+ drive-strength = <2>; /* 2 mA */
+ };
+
+ cci0_i2c1_default: cci0-i2c1-default {
+ /* SDA, SCL */
+ pins = "gpio103", "gpio104";
+ function = "cci_i2c";
+
+ bias-pull-up;
+ drive-strength = <2>; /* 2 mA */
+ };
+ };
+
+ cci0_sleep: cci0-sleep {
+ cci0_i2c0_sleep: cci0-i2c0-sleep {
+ /* SDA, SCL */
+ pins = "gpio101", "gpio102";
+ function = "cci_i2c";
+
+ drive-strength = <2>; /* 2 mA */
+ bias-pull-down;
+ };
+
+ cci0_i2c1_sleep: cci0-i2c1-sleep {
+ /* SDA, SCL */
+ pins = "gpio103", "gpio104";
+ function = "cci_i2c";
+
+ drive-strength = <2>; /* 2 mA */
+ bias-pull-down;
+ };
+ };
+
+ cci1_default: cci1-default {
+ cci1_i2c0_default: cci1-i2c0-default {
+ /* SDA, SCL */
+ pins = "gpio105","gpio106";
+ function = "cci_i2c";
+
+ bias-pull-up;
+ drive-strength = <2>; /* 2 mA */
+ };
+
+ cci1_i2c1_default: cci1-i2c1-default {
+ /* SDA, SCL */
+ pins = "gpio107","gpio108";
+ function = "cci_i2c";
+
+ bias-pull-up;
+ drive-strength = <2>; /* 2 mA */
+ };
+ };
+
+ cci1_sleep: cci1-sleep {
+ cci1_i2c0_sleep: cci1-i2c0-sleep {
+ /* SDA, SCL */
+ pins = "gpio105","gpio106";
+ function = "cci_i2c";
+
+ bias-pull-down;
+ drive-strength = <2>; /* 2 mA */
+ };
+
+ cci1_i2c1_sleep: cci1-i2c1-sleep {
+ /* SDA, SCL */
+ pins = "gpio107","gpio108";
+ function = "cci_i2c";
+
+ bias-pull-down;
+ drive-strength = <2>; /* 2 mA */
+ };
+ };
+
pri_mi2s_active: pri-mi2s-active {
sclk {
pins = "gpio138";
};
};
- apps_bcm_voter: bcm_voter {
+ apps_bcm_voter: bcm-voter {
compatible = "qcom,bcm-voter";
};
};
aliases {
ethernet0 = &gmac0;
+ ethernet1 = &gmac1;
mmc0 = &sdmmc0;
mmc1 = &sdhci;
};
regulator-max-microvolt = <5000000>;
vin-supply = <&dc_12v>;
};
+
+ vcc5v0_usb: vcc5v0_usb {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_usb";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&dc_12v>;
+ };
+
+ vcc5v0_usb_host: vcc5v0-usb-host {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vcc5v0_usb_host_en>;
+ regulator-name = "vcc5v0_usb_host";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc5v0_usb>;
+ };
+
+ vcc5v0_usb_otg: vcc5v0-usb-otg {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vcc5v0_usb_otg_en>;
+ regulator-name = "vcc5v0_usb_otg";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc5v0_usb>;
+ };
+ };
+
+ &combphy0 {
+ /* used for USB3 */
+ status = "okay";
+ };
+
+ &combphy1 {
+ /* used for USB3 */
+ status = "okay";
+ };
+
+ &combphy2 {
+ /* used for SATA */
+ status = "okay";
};
&gmac0 {
assigned-clocks = <&cru SCLK_GMAC0_RX_TX>, <&cru SCLK_GMAC0>;
assigned-clock-parents = <&cru SCLK_GMAC0_RGMII_SPEED>, <&cru CLK_MAC0_2TOP>;
clock_in_out = "input";
- phy-handle = <&rgmii_phy0>;
phy-mode = "rgmii";
pinctrl-names = "default";
pinctrl-0 = <&gmac0_miim
snps,reset-active-low;
/* Reset time is 20ms, 100ms for rtl8211f */
snps,reset-delays-us = <0 20000 100000>;
+ tx_delay = <0x4f>;
+ rx_delay = <0x0f>;
+ status = "okay";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ pause;
+ };
+};
+
+&gmac1 {
+ assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1>;
+ assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru CLK_MAC1_2TOP>;
+ clock_in_out = "output";
+ phy-handle = <&rgmii_phy1>;
+ phy-mode = "rgmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac1m1_miim
+ &gmac1m1_tx_bus2
+ &gmac1m1_rx_bus2
+ &gmac1m1_rgmii_clk
+ &gmac1m1_rgmii_bus>;
+
+ snps,reset-gpio = <&gpio3 RK_PB0 GPIO_ACTIVE_LOW>;
+ snps,reset-active-low;
+ /* Reset time is 20ms, 100ms for rtl8211f */
+ snps,reset-delays-us = <0 20000 100000>;
+
tx_delay = <0x3c>;
rx_delay = <0x2f>;
+
status = "okay";
};
status = "disabled";
};
-&mdio0 {
- rgmii_phy0: ethernet-phy@0 {
+&mdio1 {
+ rgmii_phy1: ethernet-phy@0 {
compatible = "ethernet-phy-ieee802.3-c22";
reg = <0x0>;
};
<0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
};
};
+
+ usb {
+ vcc5v0_usb_host_en: vcc5v0_usb_host_en {
+ rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ vcc5v0_usb_otg_en: vcc5v0_usb_otg_en {
+ rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
};
&pmu_io_domains {
pmuio2-supply = <&vcc3v3_pmu>;
vccio1-supply = <&vccio_acodec>;
vccio3-supply = <&vccio_sd>;
- vccio4-supply = <&vcc_1v8>;
+ vccio4-supply = <&vcc_3v3>;
vccio5-supply = <&vcc_3v3>;
- vccio6-supply = <&vcc_3v3>;
+ vccio6-supply = <&vcc_1v8>;
vccio7-supply = <&vcc_3v3>;
status = "okay";
};
status = "okay";
};
+ &sata2 {
+ status = "okay";
+ };
+
&sdhci {
bus-width = <8>;
max-frequency = <200000000>;
pinctrl-0 = <&uart9m1_xfer>;
status = "disabled";
};
+
+ &usb_host0_ehci {
+ status = "okay";
+ };
+
+ &usb_host0_ohci {
+ status = "okay";
+ };
+
+ &usb_host0_xhci {
+ extcon = <&usb2phy0>;
+ status = "okay";
+ };
+
+ &usb_host1_ehci {
+ status = "okay";
+ };
+
+ &usb_host1_ohci {
+ status = "okay";
+ };
+
+ &usb_host1_xhci {
+ status = "okay";
+ };
+
+ &usb2phy0 {
+ status = "okay";
+ };
+
+ &usb2phy0_host {
+ phy-supply = <&vcc5v0_usb_host>;
+ status = "okay";
+ };
+
+ &usb2phy0_otg {
+ phy-supply = <&vcc5v0_usb_otg>;
+ status = "okay";
+ };
projects / linux.git / commitdiff