x86/kaslr: Expose and use the end of the physical memory address space

[linux.git] / drivers / usb / dwc3 / core.h

/* SPDX-License-Identifier: GPL-2.0 */
/*
 * core.h - DesignWare USB3 DRD Core Header
 *
 * Copyright (C) 2010-2011 Texas Instruments Incorporated - https://www.ti.com
 *
 * Authors: Felipe Balbi <[email protected]>,
 *          Sebastian Andrzej Siewior <[email protected]>
 */

#ifndef __DRIVERS_USB_DWC3_CORE_H
#define __DRIVERS_USB_DWC3_CORE_H

#include <linux/device.h>
#include <linux/spinlock.h>
#include <linux/mutex.h>
#include <linux/ioport.h>
#include <linux/list.h>
#include <linux/bitops.h>
#include <linux/dma-mapping.h>
#include <linux/mm.h>
#include <linux/debugfs.h>
#include <linux/wait.h>
#include <linux/workqueue.h>

#include <linux/usb/ch9.h>
#include <linux/usb/gadget.h>
#include <linux/usb/otg.h>
#include <linux/usb/role.h>
#include <linux/ulpi/interface.h>

#include <linux/phy/phy.h>

#include <linux/power_supply.h>

/*
 * DWC3 Multiport controllers support up to 15 High-Speed PHYs
 * and 4 SuperSpeed PHYs.
 */
#define DWC3_USB2_MAX_PORTS     15
#define DWC3_USB3_MAX_PORTS     4

#define DWC3_MSG_MAX    500

/* Global constants */
#define DWC3_PULL_UP_TIMEOUT    500     /* ms */
#define DWC3_BOUNCE_SIZE        1024    /* size of a superspeed bulk */
#define DWC3_EP0_SETUP_SIZE     512
#define DWC3_ENDPOINTS_NUM      32
#define DWC3_XHCI_RESOURCES_NUM 2
#define DWC3_ISOC_MAX_RETRIES   5

#define DWC3_SCRATCHBUF_SIZE    4096    /* each buffer is assumed to be 4KiB */
#define DWC3_EVENT_BUFFERS_SIZE 4096
#define DWC3_EVENT_TYPE_MASK    0xfe

#define DWC3_EVENT_TYPE_DEV     0
#define DWC3_EVENT_TYPE_CARKIT  3
#define DWC3_EVENT_TYPE_I2C     4

#define DWC3_DEVICE_EVENT_DISCONNECT            0
#define DWC3_DEVICE_EVENT_RESET                 1
#define DWC3_DEVICE_EVENT_CONNECT_DONE          2
#define DWC3_DEVICE_EVENT_LINK_STATUS_CHANGE    3
#define DWC3_DEVICE_EVENT_WAKEUP                4
#define DWC3_DEVICE_EVENT_HIBER_REQ             5
#define DWC3_DEVICE_EVENT_SUSPEND               6
#define DWC3_DEVICE_EVENT_SOF                   7
#define DWC3_DEVICE_EVENT_ERRATIC_ERROR         9
#define DWC3_DEVICE_EVENT_CMD_CMPL              10
#define DWC3_DEVICE_EVENT_OVERFLOW              11

/* Controller's role while using the OTG block */
#define DWC3_OTG_ROLE_IDLE      0
#define DWC3_OTG_ROLE_HOST      1
#define DWC3_OTG_ROLE_DEVICE    2

#define DWC3_GEVNTCOUNT_MASK    0xfffc
#define DWC3_GEVNTCOUNT_EHB     BIT(31)
#define DWC3_GSNPSID_MASK       0xffff0000
#define DWC3_GSNPSREV_MASK      0xffff
#define DWC3_GSNPS_ID(p)        (((p) & DWC3_GSNPSID_MASK) >> 16)

/* DWC3 registers memory space boundries */
#define DWC3_XHCI_REGS_START            0x0
#define DWC3_XHCI_REGS_END              0x7fff
#define DWC3_GLOBALS_REGS_START         0xc100
#define DWC3_GLOBALS_REGS_END           0xc6ff
#define DWC3_DEVICE_REGS_START          0xc700
#define DWC3_DEVICE_REGS_END            0xcbff
#define DWC3_OTG_REGS_START             0xcc00
#define DWC3_OTG_REGS_END               0xccff

#define DWC3_RTK_RTD_GLOBALS_REGS_START 0x8100

/* Global Registers */
#define DWC3_GSBUSCFG0          0xc100
#define DWC3_GSBUSCFG1          0xc104
#define DWC3_GTXTHRCFG          0xc108
#define DWC3_GRXTHRCFG          0xc10c
#define DWC3_GCTL               0xc110
#define DWC3_GEVTEN             0xc114
#define DWC3_GSTS               0xc118
#define DWC3_GUCTL1             0xc11c
#define DWC3_GSNPSID            0xc120
#define DWC3_GGPIO              0xc124
#define DWC3_GUID               0xc128
#define DWC3_GUCTL              0xc12c
#define DWC3_GBUSERRADDR0       0xc130
#define DWC3_GBUSERRADDR1       0xc134
#define DWC3_GPRTBIMAP0         0xc138
#define DWC3_GPRTBIMAP1         0xc13c
#define DWC3_GHWPARAMS0         0xc140
#define DWC3_GHWPARAMS1         0xc144
#define DWC3_GHWPARAMS2         0xc148
#define DWC3_GHWPARAMS3         0xc14c
#define DWC3_GHWPARAMS4         0xc150
#define DWC3_GHWPARAMS5         0xc154
#define DWC3_GHWPARAMS6         0xc158
#define DWC3_GHWPARAMS7         0xc15c
#define DWC3_GDBGFIFOSPACE      0xc160
#define DWC3_GDBGLTSSM          0xc164
#define DWC3_GDBGBMU            0xc16c
#define DWC3_GDBGLSPMUX         0xc170
#define DWC3_GDBGLSP            0xc174
#define DWC3_GDBGEPINFO0        0xc178
#define DWC3_GDBGEPINFO1        0xc17c
#define DWC3_GPRTBIMAP_HS0      0xc180
#define DWC3_GPRTBIMAP_HS1      0xc184
#define DWC3_GPRTBIMAP_FS0      0xc188
#define DWC3_GPRTBIMAP_FS1      0xc18c
#define DWC3_GUCTL2             0xc19c

#define DWC3_VER_NUMBER         0xc1a0
#define DWC3_VER_TYPE           0xc1a4

#define DWC3_GUSB2PHYCFG(n)     (0xc200 + ((n) * 0x04))
#define DWC3_GUSB2I2CCTL(n)     (0xc240 + ((n) * 0x04))

#define DWC3_GUSB2PHYACC(n)     (0xc280 + ((n) * 0x04))

#define DWC3_GUSB3PIPECTL(n)    (0xc2c0 + ((n) * 0x04))

#define DWC3_GTXFIFOSIZ(n)      (0xc300 + ((n) * 0x04))
#define DWC3_GRXFIFOSIZ(n)      (0xc380 + ((n) * 0x04))

#define DWC3_GEVNTADRLO(n)      (0xc400 + ((n) * 0x10))
#define DWC3_GEVNTADRHI(n)      (0xc404 + ((n) * 0x10))
#define DWC3_GEVNTSIZ(n)        (0xc408 + ((n) * 0x10))
#define DWC3_GEVNTCOUNT(n)      (0xc40c + ((n) * 0x10))

#define DWC3_GHWPARAMS8         0xc600
#define DWC3_GUCTL3             0xc60c
#define DWC3_GFLADJ             0xc630
#define DWC3_GHWPARAMS9         0xc6e0

/* Device Registers */
#define DWC3_DCFG               0xc700
#define DWC3_DCTL               0xc704
#define DWC3_DEVTEN             0xc708
#define DWC3_DSTS               0xc70c
#define DWC3_DGCMDPAR           0xc710
#define DWC3_DGCMD              0xc714
#define DWC3_DALEPENA           0xc720
#define DWC3_DCFG1              0xc740 /* DWC_usb32 only */

#define DWC3_DEP_BASE(n)        (0xc800 + ((n) * 0x10))
#define DWC3_DEPCMDPAR2         0x00
#define DWC3_DEPCMDPAR1         0x04
#define DWC3_DEPCMDPAR0         0x08
#define DWC3_DEPCMD             0x0c

#define DWC3_DEV_IMOD(n)        (0xca00 + ((n) * 0x4))

/* OTG Registers */
#define DWC3_OCFG               0xcc00
#define DWC3_OCTL               0xcc04
#define DWC3_OEVT               0xcc08
#define DWC3_OEVTEN             0xcc0C
#define DWC3_OSTS               0xcc10

#define DWC3_LLUCTL             0xd024

/* Bit fields */

/* Global SoC Bus Configuration INCRx Register 0 */
#define DWC3_GSBUSCFG0_INCR256BRSTENA   (1 << 7) /* INCR256 burst */
#define DWC3_GSBUSCFG0_INCR128BRSTENA   (1 << 6) /* INCR128 burst */
#define DWC3_GSBUSCFG0_INCR64BRSTENA    (1 << 5) /* INCR64 burst */
#define DWC3_GSBUSCFG0_INCR32BRSTENA    (1 << 4) /* INCR32 burst */
#define DWC3_GSBUSCFG0_INCR16BRSTENA    (1 << 3) /* INCR16 burst */
#define DWC3_GSBUSCFG0_INCR8BRSTENA     (1 << 2) /* INCR8 burst */
#define DWC3_GSBUSCFG0_INCR4BRSTENA     (1 << 1) /* INCR4 burst */
#define DWC3_GSBUSCFG0_INCRBRSTENA      (1 << 0) /* undefined length enable */
#define DWC3_GSBUSCFG0_INCRBRST_MASK    0xff

/* Global SoC Bus Configuration Register: AHB-prot/AXI-cache/OCP-ReqInfo */
#define DWC3_GSBUSCFG0_REQINFO(n)       (((n) & 0xffff) << 16)
#define DWC3_GSBUSCFG0_REQINFO_UNSPECIFIED      0xffffffff

/* Global Debug LSP MUX Select */
#define DWC3_GDBGLSPMUX_ENDBC           BIT(15) /* Host only */
#define DWC3_GDBGLSPMUX_HOSTSELECT(n)   ((n) & 0x3fff)
#define DWC3_GDBGLSPMUX_DEVSELECT(n)    (((n) & 0xf) << 4)
#define DWC3_GDBGLSPMUX_EPSELECT(n)     ((n) & 0xf)

/* Global Debug Queue/FIFO Space Available Register */
#define DWC3_GDBGFIFOSPACE_NUM(n)       ((n) & 0x1f)
#define DWC3_GDBGFIFOSPACE_TYPE(n)      (((n) << 5) & 0x1e0)
#define DWC3_GDBGFIFOSPACE_SPACE_AVAILABLE(n) (((n) >> 16) & 0xffff)

#define DWC3_TXFIFO             0
#define DWC3_RXFIFO             1
#define DWC3_TXREQQ             2
#define DWC3_RXREQQ             3
#define DWC3_RXINFOQ            4
#define DWC3_PSTATQ             5
#define DWC3_DESCFETCHQ         6
#define DWC3_EVENTQ             7
#define DWC3_AUXEVENTQ          8

/* Global RX Threshold Configuration Register */
#define DWC3_GRXTHRCFG_MAXRXBURSTSIZE(n) (((n) & 0x1f) << 19)
#define DWC3_GRXTHRCFG_RXPKTCNT(n) (((n) & 0xf) << 24)
#define DWC3_GRXTHRCFG_PKTCNTSEL BIT(29)

/* Global TX Threshold Configuration Register */
#define DWC3_GTXTHRCFG_MAXTXBURSTSIZE(n) (((n) & 0xff) << 16)
#define DWC3_GTXTHRCFG_TXPKTCNT(n) (((n) & 0xf) << 24)
#define DWC3_GTXTHRCFG_PKTCNTSEL BIT(29)

/* Global RX Threshold Configuration Register for DWC_usb31 only */
#define DWC31_GRXTHRCFG_MAXRXBURSTSIZE(n)       (((n) & 0x1f) << 16)
#define DWC31_GRXTHRCFG_RXPKTCNT(n)             (((n) & 0x1f) << 21)
#define DWC31_GRXTHRCFG_PKTCNTSEL               BIT(26)
#define DWC31_RXTHRNUMPKTSEL_HS_PRD             BIT(15)
#define DWC31_RXTHRNUMPKT_HS_PRD(n)             (((n) & 0x3) << 13)
#define DWC31_RXTHRNUMPKTSEL_PRD                BIT(10)
#define DWC31_RXTHRNUMPKT_PRD(n)                (((n) & 0x1f) << 5)
#define DWC31_MAXRXBURSTSIZE_PRD(n)             ((n) & 0x1f)

/* Global TX Threshold Configuration Register for DWC_usb31 only */
#define DWC31_GTXTHRCFG_MAXTXBURSTSIZE(n)       (((n) & 0x1f) << 16)
#define DWC31_GTXTHRCFG_TXPKTCNT(n)             (((n) & 0x1f) << 21)
#define DWC31_GTXTHRCFG_PKTCNTSEL               BIT(26)
#define DWC31_TXTHRNUMPKTSEL_HS_PRD             BIT(15)
#define DWC31_TXTHRNUMPKT_HS_PRD(n)             (((n) & 0x3) << 13)
#define DWC31_TXTHRNUMPKTSEL_PRD                BIT(10)
#define DWC31_TXTHRNUMPKT_PRD(n)                (((n) & 0x1f) << 5)
#define DWC31_MAXTXBURSTSIZE_PRD(n)             ((n) & 0x1f)

/* Global Configuration Register */
#define DWC3_GCTL_PWRDNSCALE(n) ((n) << 19)
#define DWC3_GCTL_PWRDNSCALE_MASK       GENMASK(31, 19)
#define DWC3_GCTL_U2RSTECN      BIT(16)
#define DWC3_GCTL_RAMCLKSEL(x)  (((x) & DWC3_GCTL_CLK_MASK) << 6)
#define DWC3_GCTL_CLK_BUS       (0)
#define DWC3_GCTL_CLK_PIPE      (1)
#define DWC3_GCTL_CLK_PIPEHALF  (2)
#define DWC3_GCTL_CLK_MASK      (3)

#define DWC3_GCTL_PRTCAP(n)     (((n) & (3 << 12)) >> 12)
#define DWC3_GCTL_PRTCAPDIR(n)  ((n) << 12)
#define DWC3_GCTL_PRTCAP_HOST   1
#define DWC3_GCTL_PRTCAP_DEVICE 2
#define DWC3_GCTL_PRTCAP_OTG    3

#define DWC3_GCTL_CORESOFTRESET         BIT(11)
#define DWC3_GCTL_SOFITPSYNC            BIT(10)
#define DWC3_GCTL_SCALEDOWN(n)          ((n) << 4)
#define DWC3_GCTL_SCALEDOWN_MASK        DWC3_GCTL_SCALEDOWN(3)
#define DWC3_GCTL_DISSCRAMBLE           BIT(3)
#define DWC3_GCTL_U2EXIT_LFPS           BIT(2)
#define DWC3_GCTL_GBLHIBERNATIONEN      BIT(1)
#define DWC3_GCTL_DSBLCLKGTNG           BIT(0)

/* Global User Control 1 Register */
#define DWC3_GUCTL1_DEV_DECOUPLE_L1L2_EVT       BIT(31)
#define DWC3_GUCTL1_TX_IPGAP_LINECHECK_DIS      BIT(28)
#define DWC3_GUCTL1_DEV_FORCE_20_CLK_FOR_30_CLK BIT(26)
#define DWC3_GUCTL1_DEV_L1_EXIT_BY_HW           BIT(24)
#define DWC3_GUCTL1_PARKMODE_DISABLE_SS         BIT(17)
#define DWC3_GUCTL1_PARKMODE_DISABLE_HS         BIT(16)
#define DWC3_GUCTL1_RESUME_OPMODE_HS_HOST       BIT(10)

/* Global Status Register */
#define DWC3_GSTS_OTG_IP        BIT(10)
#define DWC3_GSTS_BC_IP         BIT(9)
#define DWC3_GSTS_ADP_IP        BIT(8)
#define DWC3_GSTS_HOST_IP       BIT(7)
#define DWC3_GSTS_DEVICE_IP     BIT(6)
#define DWC3_GSTS_CSR_TIMEOUT   BIT(5)
#define DWC3_GSTS_BUS_ERR_ADDR_VLD      BIT(4)
#define DWC3_GSTS_CURMOD(n)     ((n) & 0x3)
#define DWC3_GSTS_CURMOD_DEVICE 0
#define DWC3_GSTS_CURMOD_HOST   1

/* Global USB2 PHY Configuration Register */
#define DWC3_GUSB2PHYCFG_PHYSOFTRST     BIT(31)
#define DWC3_GUSB2PHYCFG_U2_FREECLK_EXISTS      BIT(30)
#define DWC3_GUSB2PHYCFG_ULPIEXTVBUSDRV BIT(17)
#define DWC3_GUSB2PHYCFG_SUSPHY         BIT(6)
#define DWC3_GUSB2PHYCFG_ULPI_UTMI      BIT(4)
#define DWC3_GUSB2PHYCFG_ENBLSLPM       BIT(8)
#define DWC3_GUSB2PHYCFG_PHYIF(n)       (n << 3)
#define DWC3_GUSB2PHYCFG_PHYIF_MASK     DWC3_GUSB2PHYCFG_PHYIF(1)
#define DWC3_GUSB2PHYCFG_USBTRDTIM(n)   (n << 10)
#define DWC3_GUSB2PHYCFG_USBTRDTIM_MASK DWC3_GUSB2PHYCFG_USBTRDTIM(0xf)
#define USBTRDTIM_UTMI_8_BIT            9
#define USBTRDTIM_UTMI_16_BIT           5
#define UTMI_PHYIF_16_BIT               1
#define UTMI_PHYIF_8_BIT                0

/* Global USB2 PHY Vendor Control Register */
#define DWC3_GUSB2PHYACC_NEWREGREQ      BIT(25)
#define DWC3_GUSB2PHYACC_DONE           BIT(24)
#define DWC3_GUSB2PHYACC_BUSY           BIT(23)
#define DWC3_GUSB2PHYACC_WRITE          BIT(22)
#define DWC3_GUSB2PHYACC_ADDR(n)        (n << 16)
#define DWC3_GUSB2PHYACC_EXTEND_ADDR(n) (n << 8)
#define DWC3_GUSB2PHYACC_DATA(n)        (n & 0xff)

/* Global USB3 PIPE Control Register */
#define DWC3_GUSB3PIPECTL_PHYSOFTRST    BIT(31)
#define DWC3_GUSB3PIPECTL_U2SSINP3OK    BIT(29)
#define DWC3_GUSB3PIPECTL_DISRXDETINP3  BIT(28)
#define DWC3_GUSB3PIPECTL_UX_EXIT_PX    BIT(27)
#define DWC3_GUSB3PIPECTL_REQP1P2P3     BIT(24)
#define DWC3_GUSB3PIPECTL_DEP1P2P3(n)   ((n) << 19)
#define DWC3_GUSB3PIPECTL_DEP1P2P3_MASK DWC3_GUSB3PIPECTL_DEP1P2P3(7)
#define DWC3_GUSB3PIPECTL_DEP1P2P3_EN   DWC3_GUSB3PIPECTL_DEP1P2P3(1)
#define DWC3_GUSB3PIPECTL_DEPOCHANGE    BIT(18)
#define DWC3_GUSB3PIPECTL_SUSPHY        BIT(17)
#define DWC3_GUSB3PIPECTL_LFPSFILT      BIT(9)
#define DWC3_GUSB3PIPECTL_RX_DETOPOLL   BIT(8)
#define DWC3_GUSB3PIPECTL_TX_DEEPH_MASK DWC3_GUSB3PIPECTL_TX_DEEPH(3)
#define DWC3_GUSB3PIPECTL_TX_DEEPH(n)   ((n) << 1)

/* Global TX Fifo Size Register */
#define DWC31_GTXFIFOSIZ_TXFRAMNUM      BIT(15)         /* DWC_usb31 only */
#define DWC31_GTXFIFOSIZ_TXFDEP(n)      ((n) & 0x7fff)  /* DWC_usb31 only */
#define DWC3_GTXFIFOSIZ_TXFDEP(n)       ((n) & 0xffff)
#define DWC3_GTXFIFOSIZ_TXFSTADDR(n)    ((n) & 0xffff0000)

/* Global RX Fifo Size Register */
#define DWC31_GRXFIFOSIZ_RXFDEP(n)      ((n) & 0x7fff)  /* DWC_usb31 only */
#define DWC3_GRXFIFOSIZ_RXFDEP(n)       ((n) & 0xffff)

/* Global Event Size Registers */
#define DWC3_GEVNTSIZ_INTMASK           BIT(31)
#define DWC3_GEVNTSIZ_SIZE(n)           ((n) & 0xffff)

/* Global HWPARAMS0 Register */
#define DWC3_GHWPARAMS0_MODE(n)         ((n) & 0x3)
#define DWC3_GHWPARAMS0_MODE_GADGET     0
#define DWC3_GHWPARAMS0_MODE_HOST       1
#define DWC3_GHWPARAMS0_MODE_DRD        2
#define DWC3_GHWPARAMS0_MBUS_TYPE(n)    (((n) >> 3) & 0x7)
#define DWC3_GHWPARAMS0_SBUS_TYPE(n)    (((n) >> 6) & 0x3)
#define DWC3_GHWPARAMS0_MDWIDTH(n)      (((n) >> 8) & 0xff)
#define DWC3_GHWPARAMS0_SDWIDTH(n)      (((n) >> 16) & 0xff)
#define DWC3_GHWPARAMS0_AWIDTH(n)       (((n) >> 24) & 0xff)

/* Global HWPARAMS1 Register */
#define DWC3_GHWPARAMS1_EN_PWROPT(n)    (((n) & (3 << 24)) >> 24)
#define DWC3_GHWPARAMS1_EN_PWROPT_NO    0
#define DWC3_GHWPARAMS1_EN_PWROPT_CLK   1
#define DWC3_GHWPARAMS1_EN_PWROPT_HIB   2
#define DWC3_GHWPARAMS1_PWROPT(n)       ((n) << 24)
#define DWC3_GHWPARAMS1_PWROPT_MASK     DWC3_GHWPARAMS1_PWROPT(3)
#define DWC3_GHWPARAMS1_ENDBC           BIT(31)

/* Global HWPARAMS3 Register */
#define DWC3_GHWPARAMS3_SSPHY_IFC(n)            ((n) & 3)
#define DWC3_GHWPARAMS3_SSPHY_IFC_DIS           0
#define DWC3_GHWPARAMS3_SSPHY_IFC_GEN1          1
#define DWC3_GHWPARAMS3_SSPHY_IFC_GEN2          2 /* DWC_usb31 only */
#define DWC3_GHWPARAMS3_HSPHY_IFC(n)            (((n) & (3 << 2)) >> 2)
#define DWC3_GHWPARAMS3_HSPHY_IFC_DIS           0
#define DWC3_GHWPARAMS3_HSPHY_IFC_UTMI          1
#define DWC3_GHWPARAMS3_HSPHY_IFC_ULPI          2
#define DWC3_GHWPARAMS3_HSPHY_IFC_UTMI_ULPI     3
#define DWC3_GHWPARAMS3_FSPHY_IFC(n)            (((n) & (3 << 4)) >> 4)
#define DWC3_GHWPARAMS3_FSPHY_IFC_DIS           0
#define DWC3_GHWPARAMS3_FSPHY_IFC_ENA           1

/* Global HWPARAMS4 Register */
#define DWC3_GHWPARAMS4_HIBER_SCRATCHBUFS(n)    (((n) & (0x0f << 13)) >> 13)
#define DWC3_MAX_HIBER_SCRATCHBUFS              15

/* Global HWPARAMS6 Register */
#define DWC3_GHWPARAMS6_BCSUPPORT               BIT(14)
#define DWC3_GHWPARAMS6_OTG3SUPPORT             BIT(13)
#define DWC3_GHWPARAMS6_ADPSUPPORT              BIT(12)
#define DWC3_GHWPARAMS6_HNPSUPPORT              BIT(11)
#define DWC3_GHWPARAMS6_SRPSUPPORT              BIT(10)
#define DWC3_GHWPARAMS6_EN_FPGA                 BIT(7)

/* DWC_usb32 only */
#define DWC3_GHWPARAMS6_MDWIDTH(n)              ((n) & (0x3 << 8))

/* Global HWPARAMS7 Register */
#define DWC3_GHWPARAMS7_RAM1_DEPTH(n)   ((n) & 0xffff)
#define DWC3_GHWPARAMS7_RAM2_DEPTH(n)   (((n) >> 16) & 0xffff)

/* Global HWPARAMS9 Register */
#define DWC3_GHWPARAMS9_DEV_TXF_FLUSH_BYPASS    BIT(0)
#define DWC3_GHWPARAMS9_DEV_MST                 BIT(1)

/* Global Frame Length Adjustment Register */
#define DWC3_GFLADJ_30MHZ_SDBND_SEL             BIT(7)
#define DWC3_GFLADJ_30MHZ_MASK                  0x3f
#define DWC3_GFLADJ_REFCLK_FLADJ_MASK           GENMASK(21, 8)
#define DWC3_GFLADJ_REFCLK_LPM_SEL              BIT(23)
#define DWC3_GFLADJ_240MHZDECR                  GENMASK(30, 24)
#define DWC3_GFLADJ_240MHZDECR_PLS1             BIT(31)

/* Global User Control Register*/
#define DWC3_GUCTL_REFCLKPER_MASK               0xffc00000
#define DWC3_GUCTL_REFCLKPER_SEL                22

/* Global User Control Register 2 */
#define DWC3_GUCTL2_RST_ACTBITLATER             BIT(14)

/* Global User Control Register 3 */
#define DWC3_GUCTL3_SPLITDISABLE                BIT(14)

/* Device Configuration Register */
#define DWC3_DCFG_NUMLANES(n)   (((n) & 0x3) << 30) /* DWC_usb32 only */

#define DWC3_DCFG_DEVADDR(addr) ((addr) << 3)
#define DWC3_DCFG_DEVADDR_MASK  DWC3_DCFG_DEVADDR(0x7f)

#define DWC3_DCFG_SPEED_MASK    (7 << 0)
#define DWC3_DCFG_SUPERSPEED_PLUS (5 << 0)  /* DWC_usb31 only */
#define DWC3_DCFG_SUPERSPEED    (4 << 0)
#define DWC3_DCFG_HIGHSPEED     (0 << 0)
#define DWC3_DCFG_FULLSPEED     BIT(0)

#define DWC3_DCFG_NUMP_SHIFT    17
#define DWC3_DCFG_NUMP(n)       (((n) >> DWC3_DCFG_NUMP_SHIFT) & 0x1f)
#define DWC3_DCFG_NUMP_MASK     (0x1f << DWC3_DCFG_NUMP_SHIFT)
#define DWC3_DCFG_LPM_CAP       BIT(22)
#define DWC3_DCFG_IGNSTRMPP     BIT(23)

/* Device Control Register */
#define DWC3_DCTL_RUN_STOP      BIT(31)
#define DWC3_DCTL_CSFTRST       BIT(30)
#define DWC3_DCTL_LSFTRST       BIT(29)

#define DWC3_DCTL_HIRD_THRES_MASK       (0x1f << 24)
#define DWC3_DCTL_HIRD_THRES(n) ((n) << 24)

#define DWC3_DCTL_APPL1RES      BIT(23)

/* These apply for core versions 1.87a and earlier */
#define DWC3_DCTL_TRGTULST_MASK         (0x0f << 17)
#define DWC3_DCTL_TRGTULST(n)           ((n) << 17)
#define DWC3_DCTL_TRGTULST_U2           (DWC3_DCTL_TRGTULST(2))
#define DWC3_DCTL_TRGTULST_U3           (DWC3_DCTL_TRGTULST(3))
#define DWC3_DCTL_TRGTULST_SS_DIS       (DWC3_DCTL_TRGTULST(4))
#define DWC3_DCTL_TRGTULST_RX_DET       (DWC3_DCTL_TRGTULST(5))
#define DWC3_DCTL_TRGTULST_SS_INACT     (DWC3_DCTL_TRGTULST(6))

/* These apply for core versions 1.94a and later */
#define DWC3_DCTL_NYET_THRES(n)         (((n) & 0xf) << 20)

#define DWC3_DCTL_KEEP_CONNECT          BIT(19)
#define DWC3_DCTL_L1_HIBER_EN           BIT(18)
#define DWC3_DCTL_CRS                   BIT(17)
#define DWC3_DCTL_CSS                   BIT(16)

#define DWC3_DCTL_INITU2ENA             BIT(12)
#define DWC3_DCTL_ACCEPTU2ENA           BIT(11)
#define DWC3_DCTL_INITU1ENA             BIT(10)
#define DWC3_DCTL_ACCEPTU1ENA           BIT(9)
#define DWC3_DCTL_TSTCTRL_MASK          (0xf << 1)

#define DWC3_DCTL_ULSTCHNGREQ_MASK      (0x0f << 5)
#define DWC3_DCTL_ULSTCHNGREQ(n) (((n) << 5) & DWC3_DCTL_ULSTCHNGREQ_MASK)

#define DWC3_DCTL_ULSTCHNG_NO_ACTION    (DWC3_DCTL_ULSTCHNGREQ(0))
#define DWC3_DCTL_ULSTCHNG_SS_DISABLED  (DWC3_DCTL_ULSTCHNGREQ(4))
#define DWC3_DCTL_ULSTCHNG_RX_DETECT    (DWC3_DCTL_ULSTCHNGREQ(5))
#define DWC3_DCTL_ULSTCHNG_SS_INACTIVE  (DWC3_DCTL_ULSTCHNGREQ(6))
#define DWC3_DCTL_ULSTCHNG_RECOVERY     (DWC3_DCTL_ULSTCHNGREQ(8))
#define DWC3_DCTL_ULSTCHNG_COMPLIANCE   (DWC3_DCTL_ULSTCHNGREQ(10))
#define DWC3_DCTL_ULSTCHNG_LOOPBACK     (DWC3_DCTL_ULSTCHNGREQ(11))

/* Device Event Enable Register */
#define DWC3_DEVTEN_VNDRDEVTSTRCVEDEN   BIT(12)
#define DWC3_DEVTEN_EVNTOVERFLOWEN      BIT(11)
#define DWC3_DEVTEN_CMDCMPLTEN          BIT(10)
#define DWC3_DEVTEN_ERRTICERREN         BIT(9)
#define DWC3_DEVTEN_SOFEN               BIT(7)
#define DWC3_DEVTEN_U3L2L1SUSPEN        BIT(6)
#define DWC3_DEVTEN_HIBERNATIONREQEVTEN BIT(5)
#define DWC3_DEVTEN_WKUPEVTEN           BIT(4)
#define DWC3_DEVTEN_ULSTCNGEN           BIT(3)
#define DWC3_DEVTEN_CONNECTDONEEN       BIT(2)
#define DWC3_DEVTEN_USBRSTEN            BIT(1)
#define DWC3_DEVTEN_DISCONNEVTEN        BIT(0)

#define DWC3_DSTS_CONNLANES(n)          (((n) >> 30) & 0x3) /* DWC_usb32 only */

/* Device Status Register */
#define DWC3_DSTS_DCNRD                 BIT(29)

/* This applies for core versions 1.87a and earlier */
#define DWC3_DSTS_PWRUPREQ              BIT(24)

/* These apply for core versions 1.94a and later */
#define DWC3_DSTS_RSS                   BIT(25)
#define DWC3_DSTS_SSS                   BIT(24)

#define DWC3_DSTS_COREIDLE              BIT(23)
#define DWC3_DSTS_DEVCTRLHLT            BIT(22)

#define DWC3_DSTS_USBLNKST_MASK         (0x0f << 18)
#define DWC3_DSTS_USBLNKST(n)           (((n) & DWC3_DSTS_USBLNKST_MASK) >> 18)

#define DWC3_DSTS_RXFIFOEMPTY           BIT(17)

#define DWC3_DSTS_SOFFN_MASK            (0x3fff << 3)
#define DWC3_DSTS_SOFFN(n)              (((n) & DWC3_DSTS_SOFFN_MASK) >> 3)

#define DWC3_DSTS_CONNECTSPD            (7 << 0)

#define DWC3_DSTS_SUPERSPEED_PLUS       (5 << 0) /* DWC_usb31 only */
#define DWC3_DSTS_SUPERSPEED            (4 << 0)
#define DWC3_DSTS_HIGHSPEED             (0 << 0)
#define DWC3_DSTS_FULLSPEED             BIT(0)

/* Device Generic Command Register */
#define DWC3_DGCMD_SET_LMP              0x01
#define DWC3_DGCMD_SET_PERIODIC_PAR     0x02
#define DWC3_DGCMD_XMIT_FUNCTION        0x03

/* These apply for core versions 1.94a and later */
#define DWC3_DGCMD_SET_SCRATCHPAD_ADDR_LO       0x04
#define DWC3_DGCMD_SET_SCRATCHPAD_ADDR_HI       0x05

#define DWC3_DGCMD_SELECTED_FIFO_FLUSH  0x09
#define DWC3_DGCMD_ALL_FIFO_FLUSH       0x0a
#define DWC3_DGCMD_SET_ENDPOINT_NRDY    0x0c
#define DWC3_DGCMD_SET_ENDPOINT_PRIME   0x0d
#define DWC3_DGCMD_RUN_SOC_BUS_LOOPBACK 0x10
#define DWC3_DGCMD_DEV_NOTIFICATION     0x07

#define DWC3_DGCMD_STATUS(n)            (((n) >> 12) & 0x0F)
#define DWC3_DGCMD_CMDACT               BIT(10)
#define DWC3_DGCMD_CMDIOC               BIT(8)

/* Device Generic Command Parameter Register */
#define DWC3_DGCMDPAR_FORCE_LINKPM_ACCEPT       BIT(0)
#define DWC3_DGCMDPAR_FIFO_NUM(n)               ((n) << 0)
#define DWC3_DGCMDPAR_RX_FIFO                   (0 << 5)
#define DWC3_DGCMDPAR_TX_FIFO                   BIT(5)
#define DWC3_DGCMDPAR_LOOPBACK_DIS              (0 << 0)
#define DWC3_DGCMDPAR_LOOPBACK_ENA              BIT(0)
#define DWC3_DGCMDPAR_DN_FUNC_WAKE              BIT(0)
#define DWC3_DGCMDPAR_INTF_SEL(n)               ((n) << 4)

/* Device Endpoint Command Register */
#define DWC3_DEPCMD_PARAM_SHIFT         16
#define DWC3_DEPCMD_PARAM(x)            ((x) << DWC3_DEPCMD_PARAM_SHIFT)
#define DWC3_DEPCMD_GET_RSC_IDX(x)      (((x) >> DWC3_DEPCMD_PARAM_SHIFT) & 0x7f)
#define DWC3_DEPCMD_STATUS(x)           (((x) >> 12) & 0x0F)
#define DWC3_DEPCMD_HIPRI_FORCERM       BIT(11)
#define DWC3_DEPCMD_CLEARPENDIN         BIT(11)
#define DWC3_DEPCMD_CMDACT              BIT(10)
#define DWC3_DEPCMD_CMDIOC              BIT(8)

#define DWC3_DEPCMD_DEPSTARTCFG         (0x09 << 0)
#define DWC3_DEPCMD_ENDTRANSFER         (0x08 << 0)
#define DWC3_DEPCMD_UPDATETRANSFER      (0x07 << 0)
#define DWC3_DEPCMD_STARTTRANSFER       (0x06 << 0)
#define DWC3_DEPCMD_CLEARSTALL          (0x05 << 0)
#define DWC3_DEPCMD_SETSTALL            (0x04 << 0)
/* This applies for core versions 1.90a and earlier */
#define DWC3_DEPCMD_GETSEQNUMBER        (0x03 << 0)
/* This applies for core versions 1.94a and later */
#define DWC3_DEPCMD_GETEPSTATE          (0x03 << 0)
#define DWC3_DEPCMD_SETTRANSFRESOURCE   (0x02 << 0)
#define DWC3_DEPCMD_SETEPCONFIG         (0x01 << 0)

#define DWC3_DEPCMD_CMD(x)              ((x) & 0xf)

/* The EP number goes 0..31 so ep0 is always out and ep1 is always in */
#define DWC3_DALEPENA_EP(n)             BIT(n)

/* DWC_usb32 DCFG1 config */
#define DWC3_DCFG1_DIS_MST_ENH          BIT(1)

#define DWC3_DEPCMD_TYPE_CONTROL        0
#define DWC3_DEPCMD_TYPE_ISOC           1
#define DWC3_DEPCMD_TYPE_BULK           2
#define DWC3_DEPCMD_TYPE_INTR           3

#define DWC3_DEV_IMOD_COUNT_SHIFT       16
#define DWC3_DEV_IMOD_COUNT_MASK        (0xffff << 16)
#define DWC3_DEV_IMOD_INTERVAL_SHIFT    0
#define DWC3_DEV_IMOD_INTERVAL_MASK     (0xffff << 0)

/* OTG Configuration Register */
#define DWC3_OCFG_DISPWRCUTTOFF         BIT(5)
#define DWC3_OCFG_HIBDISMASK            BIT(4)
#define DWC3_OCFG_SFTRSTMASK            BIT(3)
#define DWC3_OCFG_OTGVERSION            BIT(2)
#define DWC3_OCFG_HNPCAP                BIT(1)
#define DWC3_OCFG_SRPCAP                BIT(0)

/* OTG CTL Register */
#define DWC3_OCTL_OTG3GOERR             BIT(7)
#define DWC3_OCTL_PERIMODE              BIT(6)
#define DWC3_OCTL_PRTPWRCTL             BIT(5)
#define DWC3_OCTL_HNPREQ                BIT(4)
#define DWC3_OCTL_SESREQ                BIT(3)
#define DWC3_OCTL_TERMSELIDPULSE        BIT(2)
#define DWC3_OCTL_DEVSETHNPEN           BIT(1)
#define DWC3_OCTL_HSTSETHNPEN           BIT(0)

/* OTG Event Register */
#define DWC3_OEVT_DEVICEMODE            BIT(31)
#define DWC3_OEVT_XHCIRUNSTPSET         BIT(27)
#define DWC3_OEVT_DEVRUNSTPSET          BIT(26)
#define DWC3_OEVT_HIBENTRY              BIT(25)
#define DWC3_OEVT_CONIDSTSCHNG          BIT(24)
#define DWC3_OEVT_HRRCONFNOTIF          BIT(23)
#define DWC3_OEVT_HRRINITNOTIF          BIT(22)
#define DWC3_OEVT_ADEVIDLE              BIT(21)
#define DWC3_OEVT_ADEVBHOSTEND          BIT(20)
#define DWC3_OEVT_ADEVHOST              BIT(19)
#define DWC3_OEVT_ADEVHNPCHNG           BIT(18)
#define DWC3_OEVT_ADEVSRPDET            BIT(17)
#define DWC3_OEVT_ADEVSESSENDDET        BIT(16)
#define DWC3_OEVT_BDEVBHOSTEND          BIT(11)
#define DWC3_OEVT_BDEVHNPCHNG           BIT(10)
#define DWC3_OEVT_BDEVSESSVLDDET        BIT(9)
#define DWC3_OEVT_BDEVVBUSCHNG          BIT(8)
#define DWC3_OEVT_BSESSVLD              BIT(3)
#define DWC3_OEVT_HSTNEGSTS             BIT(2)
#define DWC3_OEVT_SESREQSTS             BIT(1)
#define DWC3_OEVT_ERROR                 BIT(0)

/* OTG Event Enable Register */
#define DWC3_OEVTEN_XHCIRUNSTPSETEN     BIT(27)
#define DWC3_OEVTEN_DEVRUNSTPSETEN      BIT(26)
#define DWC3_OEVTEN_HIBENTRYEN          BIT(25)
#define DWC3_OEVTEN_CONIDSTSCHNGEN      BIT(24)
#define DWC3_OEVTEN_HRRCONFNOTIFEN      BIT(23)
#define DWC3_OEVTEN_HRRINITNOTIFEN      BIT(22)
#define DWC3_OEVTEN_ADEVIDLEEN          BIT(21)
#define DWC3_OEVTEN_ADEVBHOSTENDEN      BIT(20)
#define DWC3_OEVTEN_ADEVHOSTEN          BIT(19)
#define DWC3_OEVTEN_ADEVHNPCHNGEN       BIT(18)
#define DWC3_OEVTEN_ADEVSRPDETEN        BIT(17)
#define DWC3_OEVTEN_ADEVSESSENDDETEN    BIT(16)
#define DWC3_OEVTEN_BDEVBHOSTENDEN      BIT(11)
#define DWC3_OEVTEN_BDEVHNPCHNGEN       BIT(10)
#define DWC3_OEVTEN_BDEVSESSVLDDETEN    BIT(9)
#define DWC3_OEVTEN_BDEVVBUSCHNGEN      BIT(8)

/* OTG Status Register */
#define DWC3_OSTS_DEVRUNSTP             BIT(13)
#define DWC3_OSTS_XHCIRUNSTP            BIT(12)
#define DWC3_OSTS_PERIPHERALSTATE       BIT(4)
#define DWC3_OSTS_XHCIPRTPOWER          BIT(3)
#define DWC3_OSTS_BSESVLD               BIT(2)
#define DWC3_OSTS_VBUSVLD               BIT(1)
#define DWC3_OSTS_CONIDSTS              BIT(0)

/* Force Gen1 speed on Gen2 link */
#define DWC3_LLUCTL_FORCE_GEN1          BIT(10)

/* Structures */

struct dwc3_trb;

/**
 * struct dwc3_event_buffer - Software event buffer representation
 * @buf: _THE_ buffer
 * @cache: The buffer cache used in the threaded interrupt
 * @length: size of this buffer
 * @lpos: event offset
 * @count: cache of last read event count register
 * @flags: flags related to this event buffer
 * @dma: dma_addr_t
 * @dwc: pointer to DWC controller
 */
struct dwc3_event_buffer {
        void                    *buf;
        void                    *cache;
        unsigned int            length;
        unsigned int            lpos;
        unsigned int            count;
        unsigned int            flags;

#define DWC3_EVENT_PENDING      BIT(0)

        dma_addr_t              dma;

        struct dwc3             *dwc;
};

#define DWC3_EP_FLAG_STALLED    BIT(0)
#define DWC3_EP_FLAG_WEDGED     BIT(1)

#define DWC3_EP_DIRECTION_TX    true
#define DWC3_EP_DIRECTION_RX    false

#define DWC3_TRB_NUM            256

/**
 * struct dwc3_ep - device side endpoint representation
 * @endpoint: usb endpoint
 * @cancelled_list: list of cancelled requests for this endpoint
 * @pending_list: list of pending requests for this endpoint
 * @started_list: list of started requests on this endpoint
 * @regs: pointer to first endpoint register
 * @trb_pool: array of transaction buffers
 * @trb_pool_dma: dma address of @trb_pool
 * @trb_enqueue: enqueue 'pointer' into TRB array
 * @trb_dequeue: dequeue 'pointer' into TRB array
 * @dwc: pointer to DWC controller
 * @saved_state: ep state saved during hibernation
 * @flags: endpoint flags (wedged, stalled, ...)
 * @number: endpoint number (1 - 15)
 * @type: set to bmAttributes & USB_ENDPOINT_XFERTYPE_MASK
 * @resource_index: Resource transfer index
 * @frame_number: set to the frame number we want this transfer to start (ISOC)
 * @interval: the interval on which the ISOC transfer is started
 * @name: a human readable name e.g. ep1out-bulk
 * @direction: true for TX, false for RX
 * @stream_capable: true when streams are enabled
 * @combo_num: the test combination BIT[15:14] of the frame number to test
 *              isochronous START TRANSFER command failure workaround
 * @start_cmd_status: the status of testing START TRANSFER command with
 *              combo_num = 'b00
 */
struct dwc3_ep {
        struct usb_ep           endpoint;
        struct list_head        cancelled_list;
        struct list_head        pending_list;
        struct list_head        started_list;

        void __iomem            *regs;

        struct dwc3_trb         *trb_pool;
        dma_addr_t              trb_pool_dma;
        struct dwc3             *dwc;

        u32                     saved_state;
        unsigned int            flags;
#define DWC3_EP_ENABLED                 BIT(0)
#define DWC3_EP_STALL                   BIT(1)
#define DWC3_EP_WEDGE                   BIT(2)
#define DWC3_EP_TRANSFER_STARTED        BIT(3)
#define DWC3_EP_END_TRANSFER_PENDING    BIT(4)
#define DWC3_EP_PENDING_REQUEST         BIT(5)
#define DWC3_EP_DELAY_START             BIT(6)
#define DWC3_EP_WAIT_TRANSFER_COMPLETE  BIT(7)
#define DWC3_EP_IGNORE_NEXT_NOSTREAM    BIT(8)
#define DWC3_EP_FORCE_RESTART_STREAM    BIT(9)
#define DWC3_EP_FIRST_STREAM_PRIMED     BIT(10)
#define DWC3_EP_PENDING_CLEAR_STALL     BIT(11)
#define DWC3_EP_TXFIFO_RESIZED          BIT(12)
#define DWC3_EP_DELAY_STOP             BIT(13)
#define DWC3_EP_RESOURCE_ALLOCATED      BIT(14)

        /* This last one is specific to EP0 */
#define DWC3_EP0_DIR_IN                 BIT(31)

        /*
         * IMPORTANT: we *know* we have 256 TRBs in our @trb_pool, so we will
         * use a u8 type here. If anybody decides to increase number of TRBs to
         * anything larger than 256 - I can't see why people would want to do
         * this though - then this type needs to be changed.
         *
         * By using u8 types we ensure that our % operator when incrementing
         * enqueue and dequeue get optimized away by the compiler.
         */
        u8                      trb_enqueue;
        u8                      trb_dequeue;

        u8                      number;
        u8                      type;
        u8                      resource_index;
        u32                     frame_number;
        u32                     interval;

        char                    name[20];

        unsigned                direction:1;
        unsigned                stream_capable:1;

        /* For isochronous START TRANSFER workaround only */
        u8                      combo_num;
        int                     start_cmd_status;
};

enum dwc3_phy {
        DWC3_PHY_UNKNOWN = 0,
        DWC3_PHY_USB3,
        DWC3_PHY_USB2,
};

enum dwc3_ep0_next {
        DWC3_EP0_UNKNOWN = 0,
        DWC3_EP0_COMPLETE,
        DWC3_EP0_NRDY_DATA,
        DWC3_EP0_NRDY_STATUS,
};

enum dwc3_ep0_state {
        EP0_UNCONNECTED         = 0,
        EP0_SETUP_PHASE,
        EP0_DATA_PHASE,
        EP0_STATUS_PHASE,
};

enum dwc3_link_state {
        /* In SuperSpeed */
        DWC3_LINK_STATE_U0              = 0x00, /* in HS, means ON */
        DWC3_LINK_STATE_U1              = 0x01,
        DWC3_LINK_STATE_U2              = 0x02, /* in HS, means SLEEP */
        DWC3_LINK_STATE_U3              = 0x03, /* in HS, means SUSPEND */
        DWC3_LINK_STATE_SS_DIS          = 0x04,
        DWC3_LINK_STATE_RX_DET          = 0x05, /* in HS, means Early Suspend */
        DWC3_LINK_STATE_SS_INACT        = 0x06,
        DWC3_LINK_STATE_POLL            = 0x07,
        DWC3_LINK_STATE_RECOV           = 0x08,
        DWC3_LINK_STATE_HRESET          = 0x09,
        DWC3_LINK_STATE_CMPLY           = 0x0a,
        DWC3_LINK_STATE_LPBK            = 0x0b,
        DWC3_LINK_STATE_RESET           = 0x0e,
        DWC3_LINK_STATE_RESUME          = 0x0f,
        DWC3_LINK_STATE_MASK            = 0x0f,
};

/* TRB Length, PCM and Status */
#define DWC3_TRB_SIZE_MASK      (0x00ffffff)
#define DWC3_TRB_SIZE_LENGTH(n) ((n) & DWC3_TRB_SIZE_MASK)
#define DWC3_TRB_SIZE_PCM1(n)   (((n) & 0x03) << 24)
#define DWC3_TRB_SIZE_TRBSTS(n) (((n) & (0x0f << 28)) >> 28)

#define DWC3_TRBSTS_OK                  0
#define DWC3_TRBSTS_MISSED_ISOC         1
#define DWC3_TRBSTS_SETUP_PENDING       2
#define DWC3_TRB_STS_XFER_IN_PROG       4

/* TRB Control */
#define DWC3_TRB_CTRL_HWO               BIT(0)
#define DWC3_TRB_CTRL_LST               BIT(1)
#define DWC3_TRB_CTRL_CHN               BIT(2)
#define DWC3_TRB_CTRL_CSP               BIT(3)
#define DWC3_TRB_CTRL_TRBCTL(n)         (((n) & 0x3f) << 4)
#define DWC3_TRB_CTRL_ISP_IMI           BIT(10)
#define DWC3_TRB_CTRL_IOC               BIT(11)
#define DWC3_TRB_CTRL_SID_SOFN(n)       (((n) & 0xffff) << 14)
#define DWC3_TRB_CTRL_GET_SID_SOFN(n)   (((n) & (0xffff << 14)) >> 14)

#define DWC3_TRBCTL_TYPE(n)             ((n) & (0x3f << 4))
#define DWC3_TRBCTL_NORMAL              DWC3_TRB_CTRL_TRBCTL(1)
#define DWC3_TRBCTL_CONTROL_SETUP       DWC3_TRB_CTRL_TRBCTL(2)
#define DWC3_TRBCTL_CONTROL_STATUS2     DWC3_TRB_CTRL_TRBCTL(3)
#define DWC3_TRBCTL_CONTROL_STATUS3     DWC3_TRB_CTRL_TRBCTL(4)
#define DWC3_TRBCTL_CONTROL_DATA        DWC3_TRB_CTRL_TRBCTL(5)
#define DWC3_TRBCTL_ISOCHRONOUS_FIRST   DWC3_TRB_CTRL_TRBCTL(6)
#define DWC3_TRBCTL_ISOCHRONOUS         DWC3_TRB_CTRL_TRBCTL(7)
#define DWC3_TRBCTL_LINK_TRB            DWC3_TRB_CTRL_TRBCTL(8)

/**
 * struct dwc3_trb - transfer request block (hw format)
 * @bpl: DW0-3
 * @bph: DW4-7
 * @size: DW8-B
 * @ctrl: DWC-F
 */
struct dwc3_trb {
        u32             bpl;
        u32             bph;
        u32             size;
        u32             ctrl;
} __packed;

/**
 * struct dwc3_hwparams - copy of HWPARAMS registers
 * @hwparams0: GHWPARAMS0
 * @hwparams1: GHWPARAMS1
 * @hwparams2: GHWPARAMS2
 * @hwparams3: GHWPARAMS3
 * @hwparams4: GHWPARAMS4
 * @hwparams5: GHWPARAMS5
 * @hwparams6: GHWPARAMS6
 * @hwparams7: GHWPARAMS7
 * @hwparams8: GHWPARAMS8
 * @hwparams9: GHWPARAMS9
 */
struct dwc3_hwparams {
        u32     hwparams0;
        u32     hwparams1;
        u32     hwparams2;
        u32     hwparams3;
        u32     hwparams4;
        u32     hwparams5;
        u32     hwparams6;
        u32     hwparams7;
        u32     hwparams8;
        u32     hwparams9;
};

/* HWPARAMS0 */
#define DWC3_MODE(n)            ((n) & 0x7)

/* HWPARAMS1 */
#define DWC3_NUM_INT(n)         (((n) & (0x3f << 15)) >> 15)

/* HWPARAMS3 */
#define DWC3_NUM_IN_EPS_MASK    (0x1f << 18)
#define DWC3_NUM_EPS_MASK       (0x3f << 12)
#define DWC3_NUM_EPS(p)         (((p)->hwparams3 &              \
                        (DWC3_NUM_EPS_MASK)) >> 12)
#define DWC3_NUM_IN_EPS(p)      (((p)->hwparams3 &              \
                        (DWC3_NUM_IN_EPS_MASK)) >> 18)

/* HWPARAMS7 */
#define DWC3_RAM1_DEPTH(n)      ((n) & 0xffff)

/* HWPARAMS9 */
#define DWC3_MST_CAPABLE(p)     (!!((p)->hwparams9 &            \
                        DWC3_GHWPARAMS9_DEV_MST))

/**
 * struct dwc3_request - representation of a transfer request
 * @request: struct usb_request to be transferred
 * @list: a list_head used for request queueing
 * @dep: struct dwc3_ep owning this request
 * @sg: pointer to first incomplete sg
 * @start_sg: pointer to the sg which should be queued next
 * @num_pending_sgs: counter to pending sgs
 * @num_queued_sgs: counter to the number of sgs which already got queued
 * @remaining: amount of data remaining
 * @status: internal dwc3 request status tracking
 * @epnum: endpoint number to which this request refers
 * @trb: pointer to struct dwc3_trb
 * @trb_dma: DMA address of @trb
 * @num_trbs: number of TRBs used by this request
 * @needs_extra_trb: true when request needs one extra TRB (either due to ZLP
 *      or unaligned OUT)
 * @direction: IN or OUT direction flag
 * @mapped: true when request has been dma-mapped
 */
struct dwc3_request {
        struct usb_request      request;
        struct list_head        list;
        struct dwc3_ep          *dep;
        struct scatterlist      *sg;
        struct scatterlist      *start_sg;

        unsigned int            num_pending_sgs;
        unsigned int            num_queued_sgs;
        unsigned int            remaining;

        unsigned int            status;
#define DWC3_REQUEST_STATUS_QUEUED              0
#define DWC3_REQUEST_STATUS_STARTED             1
#define DWC3_REQUEST_STATUS_DISCONNECTED        2
#define DWC3_REQUEST_STATUS_DEQUEUED            3
#define DWC3_REQUEST_STATUS_STALLED             4
#define DWC3_REQUEST_STATUS_COMPLETED           5
#define DWC3_REQUEST_STATUS_UNKNOWN             -1

        u8                      epnum;
        struct dwc3_trb         *trb;
        dma_addr_t              trb_dma;

        unsigned int            num_trbs;

        unsigned int            needs_extra_trb:1;
        unsigned int            direction:1;
        unsigned int            mapped:1;
};

/*
 * struct dwc3_scratchpad_array - hibernation scratchpad array
 * (format defined by hw)
 */
struct dwc3_scratchpad_array {
        __le64  dma_adr[DWC3_MAX_HIBER_SCRATCHBUFS];
};

/**
 * struct dwc3 - representation of our controller
 * @drd_work: workqueue used for role swapping
 * @ep0_trb: trb which is used for the ctrl_req
 * @bounce: address of bounce buffer
 * @setup_buf: used while precessing STD USB requests
 * @ep0_trb_addr: dma address of @ep0_trb
 * @bounce_addr: dma address of @bounce
 * @ep0_usb_req: dummy req used while handling STD USB requests
 * @ep0_in_setup: one control transfer is completed and enter setup phase
 * @lock: for synchronizing
 * @mutex: for mode switching
 * @dev: pointer to our struct device
 * @sysdev: pointer to the DMA-capable device
 * @xhci: pointer to our xHCI child
 * @xhci_resources: struct resources for our @xhci child
 * @ev_buf: struct dwc3_event_buffer pointer
 * @eps: endpoint array
 * @gadget: device side representation of the peripheral controller
 * @gadget_driver: pointer to the gadget driver
 * @bus_clk: clock for accessing the registers
 * @ref_clk: reference clock
 * @susp_clk: clock used when the SS phy is in low power (S3) state
 * @utmi_clk: clock used for USB2 PHY communication
 * @pipe_clk: clock used for USB3 PHY communication
 * @reset: reset control
 * @regs: base address for our registers
 * @regs_size: address space size
 * @fladj: frame length adjustment
 * @ref_clk_per: reference clock period configuration
 * @irq_gadget: peripheral controller's IRQ number
 * @otg_irq: IRQ number for OTG IRQs
 * @current_otg_role: current role of operation while using the OTG block
 * @desired_otg_role: desired role of operation while using the OTG block
 * @otg_restart_host: flag that OTG controller needs to restart host
 * @u1u2: only used on revisions <1.83a for workaround
 * @maximum_speed: maximum speed requested (mainly for testing purposes)
 * @max_ssp_rate: SuperSpeed Plus maximum signaling rate and lane count
 * @gadget_max_speed: maximum gadget speed requested
 * @gadget_ssp_rate: Gadget driver's maximum supported SuperSpeed Plus signaling
 *                      rate and lane count.
 * @ip: controller's ID
 * @revision: controller's version of an IP
 * @version_type: VERSIONTYPE register contents, a sub release of a revision
 * @dr_mode: requested mode of operation
 * @current_dr_role: current role of operation when in dual-role mode
 * @desired_dr_role: desired role of operation when in dual-role mode
 * @edev: extcon handle
 * @edev_nb: extcon notifier
 * @hsphy_mode: UTMI phy mode, one of following:
 *              - USBPHY_INTERFACE_MODE_UTMI
 *              - USBPHY_INTERFACE_MODE_UTMIW
 * @role_sw: usb_role_switch handle
 * @role_switch_default_mode: default operation mode of controller while
 *                      usb role is USB_ROLE_NONE.
 * @usb_psy: pointer to power supply interface.
 * @usb2_phy: pointer to USB2 PHY
 * @usb3_phy: pointer to USB3 PHY
 * @usb2_generic_phy: pointer to array of USB2 PHYs
 * @usb3_generic_phy: pointer to array of USB3 PHYs
 * @num_usb2_ports: number of USB2 ports
 * @num_usb3_ports: number of USB3 ports
 * @phys_ready: flag to indicate that PHYs are ready
 * @ulpi: pointer to ulpi interface
 * @ulpi_ready: flag to indicate that ULPI is initialized
 * @u2sel: parameter from Set SEL request.
 * @u2pel: parameter from Set SEL request.
 * @u1sel: parameter from Set SEL request.
 * @u1pel: parameter from Set SEL request.
 * @num_eps: number of endpoints
 * @ep0_next_event: hold the next expected event
 * @ep0state: state of endpoint zero
 * @link_state: link state
 * @speed: device speed (super, high, full, low)
 * @hwparams: copy of hwparams registers
 * @regset: debugfs pointer to regdump file
 * @dbg_lsp_select: current debug lsp mux register selection
 * @test_mode: true when we're entering a USB test mode
 * @test_mode_nr: test feature selector
 * @lpm_nyet_threshold: LPM NYET response threshold
 * @hird_threshold: HIRD threshold
 * @rx_thr_num_pkt: USB receive packet count
 * @rx_max_burst: max USB receive burst size
 * @tx_thr_num_pkt: USB transmit packet count
 * @tx_max_burst: max USB transmit burst size
 * @rx_thr_num_pkt_prd: periodic ESS receive packet count
 * @rx_max_burst_prd: max periodic ESS receive burst size
 * @tx_thr_num_pkt_prd: periodic ESS transmit packet count
 * @tx_max_burst_prd: max periodic ESS transmit burst size
 * @tx_fifo_resize_max_num: max number of fifos allocated during txfifo resize
 * @clear_stall_protocol: endpoint number that requires a delayed status phase
 * @hsphy_interface: "utmi" or "ulpi"
 * @connected: true when we're connected to a host, false otherwise
 * @softconnect: true when gadget connect is called, false when disconnect runs
 * @delayed_status: true when gadget driver asks for delayed status
 * @ep0_bounced: true when we used bounce buffer
 * @ep0_expect_in: true when we expect a DATA IN transfer
 * @sysdev_is_parent: true when dwc3 device has a parent driver
 * @has_lpm_erratum: true when core was configured with LPM Erratum. Note that
 *                      there's now way for software to detect this in runtime.
 * @is_utmi_l1_suspend: the core asserts output signal
 *      0       - utmi_sleep_n
 *      1       - utmi_l1_suspend_n
 * @is_fpga: true when we are using the FPGA board
 * @pending_events: true when we have pending IRQs to be handled
 * @do_fifo_resize: true when txfifo resizing is enabled for dwc3 endpoints
 * @pullups_connected: true when Run/Stop bit is set
 * @setup_packet_pending: true when there's a Setup Packet in FIFO. Workaround
 * @three_stage_setup: set if we perform a three phase setup
 * @dis_start_transfer_quirk: set if start_transfer failure SW workaround is
 *                      not needed for DWC_usb31 version 1.70a-ea06 and below
 * @usb3_lpm_capable: set if hadrware supports Link Power Management
 * @usb2_lpm_disable: set to disable usb2 lpm for host
 * @usb2_gadget_lpm_disable: set to disable usb2 lpm for gadget
 * @disable_scramble_quirk: set if we enable the disable scramble quirk
 * @u2exit_lfps_quirk: set if we enable u2exit lfps quirk
 * @u2ss_inp3_quirk: set if we enable P3 OK for U2/SS Inactive quirk
 * @req_p1p2p3_quirk: set if we enable request p1p2p3 quirk
 * @del_p1p2p3_quirk: set if we enable delay p1p2p3 quirk
 * @del_phy_power_chg_quirk: set if we enable delay phy power change quirk
 * @lfps_filter_quirk: set if we enable LFPS filter quirk
 * @rx_detect_poll_quirk: set if we enable rx_detect to polling lfps quirk
 * @dis_u3_susphy_quirk: set if we disable usb3 suspend phy
 * @dis_u2_susphy_quirk: set if we disable usb2 suspend phy
 * @dis_enblslpm_quirk: set if we clear enblslpm in GUSB2PHYCFG,
 *                      disabling the suspend signal to the PHY.
 * @dis_u1_entry_quirk: set if link entering into U1 state needs to be disabled.
 * @dis_u2_entry_quirk: set if link entering into U2 state needs to be disabled.
 * @dis_rxdet_inp3_quirk: set if we disable Rx.Detect in P3
 * @async_callbacks: if set, indicate that async callbacks will be used.
 *
 * @dis_u2_freeclk_exists_quirk : set if we clear u2_freeclk_exists
 *                      in GUSB2PHYCFG, specify that USB2 PHY doesn't
 *                      provide a free-running PHY clock.
 * @dis_del_phy_power_chg_quirk: set if we disable delay phy power
 *                      change quirk.
 * @dis_tx_ipgap_linecheck_quirk: set if we disable u2mac linestate
 *                      check during HS transmit.
 * @resume_hs_terminations: Set if we enable quirk for fixing improper crc
 *                      generation after resume from suspend.
 * @ulpi_ext_vbus_drv: Set to confiure the upli chip to drives CPEN pin
 *                      VBUS with an external supply.
 * @parkmode_disable_ss_quirk: set if we need to disable all SuperSpeed
 *                      instances in park mode.
 * @parkmode_disable_hs_quirk: set if we need to disable all HishSpeed
 *                      instances in park mode.
 * @gfladj_refclk_lpm_sel: set if we need to enable SOF/ITP counter
 *                          running based on ref_clk
 * @tx_de_emphasis_quirk: set if we enable Tx de-emphasis quirk
 * @tx_de_emphasis: Tx de-emphasis value
 *      0       - -6dB de-emphasis
 *      1       - -3.5dB de-emphasis
 *      2       - No de-emphasis
 *      3       - Reserved
 * @dis_metastability_quirk: set to disable metastability quirk.
 * @dis_split_quirk: set to disable split boundary.
 * @sys_wakeup: set if the device may do system wakeup.
 * @wakeup_configured: set if the device is configured for remote wakeup.
 * @suspended: set to track suspend event due to U3/L2.
 * @imod_interval: set the interrupt moderation interval in 250ns
 *                      increments or 0 to disable.
 * @max_cfg_eps: current max number of IN eps used across all USB configs.
 * @last_fifo_depth: last fifo depth used to determine next fifo ram start
 *                   address.
 * @num_ep_resized: carries the current number endpoints which have had its tx
 *                  fifo resized.
 * @debug_root: root debugfs directory for this device to put its files in.
 * @gsbuscfg0_reqinfo: store GSBUSCFG0.DATRDREQINFO, DESRDREQINFO,
 *                     DATWRREQINFO, and DESWRREQINFO value passed from
 *                     glue driver.
 */
struct dwc3 {
        struct work_struct      drd_work;
        struct dwc3_trb         *ep0_trb;
        void                    *bounce;
        u8                      *setup_buf;
        dma_addr_t              ep0_trb_addr;
        dma_addr_t              bounce_addr;
        struct dwc3_request     ep0_usb_req;
        struct completion       ep0_in_setup;

        /* device lock */
        spinlock_t              lock;

        /* mode switching lock */
        struct mutex            mutex;

        struct device           *dev;
        struct device           *sysdev;

        struct platform_device  *xhci;
        struct resource         xhci_resources[DWC3_XHCI_RESOURCES_NUM];

        struct dwc3_event_buffer *ev_buf;
        struct dwc3_ep          *eps[DWC3_ENDPOINTS_NUM];

        struct usb_gadget       *gadget;
        struct usb_gadget_driver *gadget_driver;

        struct clk              *bus_clk;
        struct clk              *ref_clk;
        struct clk              *susp_clk;
        struct clk              *utmi_clk;
        struct clk              *pipe_clk;

        struct reset_control    *reset;

        struct usb_phy          *usb2_phy;
        struct usb_phy          *usb3_phy;

        struct phy              *usb2_generic_phy[DWC3_USB2_MAX_PORTS];
        struct phy              *usb3_generic_phy[DWC3_USB3_MAX_PORTS];

        u8                      num_usb2_ports;
        u8                      num_usb3_ports;

        bool                    phys_ready;

        struct ulpi             *ulpi;
        bool                    ulpi_ready;

        void __iomem            *regs;
        size_t                  regs_size;

        enum usb_dr_mode        dr_mode;
        u32                     current_dr_role;
        u32                     desired_dr_role;
        struct extcon_dev       *edev;
        struct notifier_block   edev_nb;
        enum usb_phy_interface  hsphy_mode;
        struct usb_role_switch  *role_sw;
        enum usb_dr_mode        role_switch_default_mode;

        struct power_supply     *usb_psy;

        u32                     fladj;
        u32                     ref_clk_per;
        u32                     irq_gadget;
        u32                     otg_irq;
        u32                     current_otg_role;
        u32                     desired_otg_role;
        bool                    otg_restart_host;
        u32                     u1u2;
        u32                     maximum_speed;
        u32                     gadget_max_speed;
        enum usb_ssp_rate       max_ssp_rate;
        enum usb_ssp_rate       gadget_ssp_rate;

        u32                     ip;

#define DWC3_IP                 0x5533
#define DWC31_IP                0x3331
#define DWC32_IP                0x3332

        u32                     revision;

#define DWC3_REVISION_ANY       0x0
#define DWC3_REVISION_173A      0x5533173a
#define DWC3_REVISION_175A      0x5533175a
#define DWC3_REVISION_180A      0x5533180a
#define DWC3_REVISION_183A      0x5533183a
#define DWC3_REVISION_185A      0x5533185a
#define DWC3_REVISION_187A      0x5533187a
#define DWC3_REVISION_188A      0x5533188a
#define DWC3_REVISION_190A      0x5533190a
#define DWC3_REVISION_194A      0x5533194a
#define DWC3_REVISION_200A      0x5533200a
#define DWC3_REVISION_202A      0x5533202a
#define DWC3_REVISION_210A      0x5533210a
#define DWC3_REVISION_220A      0x5533220a
#define DWC3_REVISION_230A      0x5533230a
#define DWC3_REVISION_240A      0x5533240a
#define DWC3_REVISION_250A      0x5533250a
#define DWC3_REVISION_260A      0x5533260a
#define DWC3_REVISION_270A      0x5533270a
#define DWC3_REVISION_280A      0x5533280a
#define DWC3_REVISION_290A      0x5533290a
#define DWC3_REVISION_300A      0x5533300a
#define DWC3_REVISION_310A      0x5533310a
#define DWC3_REVISION_330A      0x5533330a

#define DWC31_REVISION_ANY      0x0
#define DWC31_REVISION_110A     0x3131302a
#define DWC31_REVISION_120A     0x3132302a
#define DWC31_REVISION_160A     0x3136302a
#define DWC31_REVISION_170A     0x3137302a
#define DWC31_REVISION_180A     0x3138302a
#define DWC31_REVISION_190A     0x3139302a
#define DWC31_REVISION_200A     0x3230302a

#define DWC32_REVISION_ANY      0x0
#define DWC32_REVISION_100A     0x3130302a

        u32                     version_type;

#define DWC31_VERSIONTYPE_ANY           0x0
#define DWC31_VERSIONTYPE_EA01          0x65613031
#define DWC31_VERSIONTYPE_EA02          0x65613032
#define DWC31_VERSIONTYPE_EA03          0x65613033
#define DWC31_VERSIONTYPE_EA04          0x65613034
#define DWC31_VERSIONTYPE_EA05          0x65613035
#define DWC31_VERSIONTYPE_EA06          0x65613036

        enum dwc3_ep0_next      ep0_next_event;
        enum dwc3_ep0_state     ep0state;
        enum dwc3_link_state    link_state;

        u16                     u2sel;
        u16                     u2pel;
        u8                      u1sel;
        u8                      u1pel;

        u8                      speed;

        u8                      num_eps;

        struct dwc3_hwparams    hwparams;
        struct debugfs_regset32 *regset;

        u32                     dbg_lsp_select;

        u8                      test_mode;
        u8                      test_mode_nr;
        u8                      lpm_nyet_threshold;
        u8                      hird_threshold;
        u8                      rx_thr_num_pkt;
        u8                      rx_max_burst;
        u8                      tx_thr_num_pkt;
        u8                      tx_max_burst;
        u8                      rx_thr_num_pkt_prd;
        u8                      rx_max_burst_prd;
        u8                      tx_thr_num_pkt_prd;
        u8                      tx_max_burst_prd;
        u8                      tx_fifo_resize_max_num;
        u8                      clear_stall_protocol;

        const char              *hsphy_interface;

        unsigned                connected:1;
        unsigned                softconnect:1;
        unsigned                delayed_status:1;
        unsigned                ep0_bounced:1;
        unsigned                ep0_expect_in:1;
        unsigned                sysdev_is_parent:1;
        unsigned                has_lpm_erratum:1;
        unsigned                is_utmi_l1_suspend:1;
        unsigned                is_fpga:1;
        unsigned                pending_events:1;
        unsigned                do_fifo_resize:1;
        unsigned                pullups_connected:1;
        unsigned                setup_packet_pending:1;
        unsigned                three_stage_setup:1;
        unsigned                dis_start_transfer_quirk:1;
        unsigned                usb3_lpm_capable:1;
        unsigned                usb2_lpm_disable:1;
        unsigned                usb2_gadget_lpm_disable:1;

        unsigned                disable_scramble_quirk:1;
        unsigned                u2exit_lfps_quirk:1;
        unsigned                u2ss_inp3_quirk:1;
        unsigned                req_p1p2p3_quirk:1;
        unsigned                del_p1p2p3_quirk:1;
        unsigned                del_phy_power_chg_quirk:1;
        unsigned                lfps_filter_quirk:1;
        unsigned                rx_detect_poll_quirk:1;
        unsigned                dis_u3_susphy_quirk:1;
        unsigned                dis_u2_susphy_quirk:1;
        unsigned                dis_enblslpm_quirk:1;
        unsigned                dis_u1_entry_quirk:1;
        unsigned                dis_u2_entry_quirk:1;
        unsigned                dis_rxdet_inp3_quirk:1;
        unsigned                dis_u2_freeclk_exists_quirk:1;
        unsigned                dis_del_phy_power_chg_quirk:1;
        unsigned                dis_tx_ipgap_linecheck_quirk:1;
        unsigned                resume_hs_terminations:1;
        unsigned                ulpi_ext_vbus_drv:1;
        unsigned                parkmode_disable_ss_quirk:1;
        unsigned                parkmode_disable_hs_quirk:1;
        unsigned                gfladj_refclk_lpm_sel:1;

        unsigned                tx_de_emphasis_quirk:1;
        unsigned                tx_de_emphasis:2;

        unsigned                dis_metastability_quirk:1;

        unsigned                dis_split_quirk:1;
        unsigned                async_callbacks:1;
        unsigned                sys_wakeup:1;
        unsigned                wakeup_configured:1;
        unsigned                suspended:1;

        u16                     imod_interval;

        int                     max_cfg_eps;
        int                     last_fifo_depth;
        int                     num_ep_resized;
        struct dentry           *debug_root;
        u32                     gsbuscfg0_reqinfo;
};

#define INCRX_BURST_MODE 0
#define INCRX_UNDEF_LENGTH_BURST_MODE 1

#define work_to_dwc(w)          (container_of((w), struct dwc3, drd_work))

/* -------------------------------------------------------------------------- */

struct dwc3_event_type {
        u32     is_devspec:1;
        u32     type:7;
        u32     reserved8_31:24;
} __packed;

#define DWC3_DEPEVT_XFERCOMPLETE        0x01
#define DWC3_DEPEVT_XFERINPROGRESS      0x02
#define DWC3_DEPEVT_XFERNOTREADY        0x03
#define DWC3_DEPEVT_RXTXFIFOEVT         0x04
#define DWC3_DEPEVT_STREAMEVT           0x06
#define DWC3_DEPEVT_EPCMDCMPLT          0x07

/**
 * struct dwc3_event_depevt - Device Endpoint Events
 * @one_bit: indicates this is an endpoint event (not used)
 * @endpoint_number: number of the endpoint
 * @endpoint_event: The event we have:
 *      0x00    - Reserved
 *      0x01    - XferComplete
 *      0x02    - XferInProgress
 *      0x03    - XferNotReady
 *      0x04    - RxTxFifoEvt (IN->Underrun, OUT->Overrun)
 *      0x05    - Reserved
 *      0x06    - StreamEvt
 *      0x07    - EPCmdCmplt
 * @reserved11_10: Reserved, don't use.
 * @status: Indicates the status of the event. Refer to databook for
 *      more information.
 * @parameters: Parameters of the current event. Refer to databook for
 *      more information.
 */
struct dwc3_event_depevt {
        u32     one_bit:1;
        u32     endpoint_number:5;
        u32     endpoint_event:4;
        u32     reserved11_10:2;
        u32     status:4;

/* Within XferNotReady */
#define DEPEVT_STATUS_TRANSFER_ACTIVE   BIT(3)

/* Within XferComplete or XferInProgress */
#define DEPEVT_STATUS_BUSERR    BIT(0)
#define DEPEVT_STATUS_SHORT     BIT(1)
#define DEPEVT_STATUS_IOC       BIT(2)
#define DEPEVT_STATUS_LST       BIT(3) /* XferComplete */
#define DEPEVT_STATUS_MISSED_ISOC BIT(3) /* XferInProgress */

/* Stream event only */
#define DEPEVT_STREAMEVT_FOUND          1
#define DEPEVT_STREAMEVT_NOTFOUND       2

/* Stream event parameter */
#define DEPEVT_STREAM_PRIME             0xfffe
#define DEPEVT_STREAM_NOSTREAM          0x0

/* Control-only Status */
#define DEPEVT_STATUS_CONTROL_DATA      1
#define DEPEVT_STATUS_CONTROL_STATUS    2
#define DEPEVT_STATUS_CONTROL_PHASE(n)  ((n) & 3)

/* In response to Start Transfer */
#define DEPEVT_TRANSFER_NO_RESOURCE     1
#define DEPEVT_TRANSFER_BUS_EXPIRY      2

        u32     parameters:16;

/* For Command Complete Events */
#define DEPEVT_PARAMETER_CMD(n) (((n) & (0xf << 8)) >> 8)
} __packed;

/**
 * struct dwc3_event_devt - Device Events
 * @one_bit: indicates this is a non-endpoint event (not used)
 * @device_event: indicates it's a device event. Should read as 0x00
 * @type: indicates the type of device event.
 *      0       - DisconnEvt
 *      1       - USBRst
 *      2       - ConnectDone
 *      3       - ULStChng
 *      4       - WkUpEvt
 *      5       - Reserved
 *      6       - Suspend (EOPF on revisions 2.10a and prior)
 *      7       - SOF
 *      8       - Reserved
 *      9       - ErrticErr
 *      10      - CmdCmplt
 *      11      - EvntOverflow
 *      12      - VndrDevTstRcved
 * @reserved15_12: Reserved, not used
 * @event_info: Information about this event
 * @reserved31_25: Reserved, not used
 */
struct dwc3_event_devt {
        u32     one_bit:1;
        u32     device_event:7;
        u32     type:4;
        u32     reserved15_12:4;
        u32     event_info:9;
        u32     reserved31_25:7;
} __packed;

/**
 * struct dwc3_event_gevt - Other Core Events
 * @one_bit: indicates this is a non-endpoint event (not used)
 * @device_event: indicates it's (0x03) Carkit or (0x04) I2C event.
 * @phy_port_number: self-explanatory
 * @reserved31_12: Reserved, not used.
 */
struct dwc3_event_gevt {
        u32     one_bit:1;
        u32     device_event:7;
        u32     phy_port_number:4;
        u32     reserved31_12:20;
} __packed;

/**
 * union dwc3_event - representation of Event Buffer contents
 * @raw: raw 32-bit event
 * @type: the type of the event
 * @depevt: Device Endpoint Event
 * @devt: Device Event
 * @gevt: Global Event
 */
union dwc3_event {
        u32                             raw;
        struct dwc3_event_type          type;
        struct dwc3_event_depevt        depevt;
        struct dwc3_event_devt          devt;
        struct dwc3_event_gevt          gevt;
};

/**
 * struct dwc3_gadget_ep_cmd_params - representation of endpoint command
 * parameters
 * @param2: third parameter
 * @param1: second parameter
 * @param0: first parameter
 */
struct dwc3_gadget_ep_cmd_params {
        u32     param2;
        u32     param1;
        u32     param0;
};

/*
 * DWC3 Features to be used as Driver Data
 */

#define DWC3_HAS_PERIPHERAL             BIT(0)
#define DWC3_HAS_XHCI                   BIT(1)
#define DWC3_HAS_OTG                    BIT(3)

/* prototypes */
void dwc3_set_prtcap(struct dwc3 *dwc, u32 mode);
void dwc3_set_mode(struct dwc3 *dwc, u32 mode);
u32 dwc3_core_fifo_space(struct dwc3_ep *dep, u8 type);

#define DWC3_IP_IS(_ip)                                                 \
        (dwc->ip == _ip##_IP)

#define DWC3_VER_IS(_ip, _ver)                                          \
        (DWC3_IP_IS(_ip) && dwc->revision == _ip##_REVISION_##_ver)

#define DWC3_VER_IS_PRIOR(_ip, _ver)                                    \
        (DWC3_IP_IS(_ip) && dwc->revision < _ip##_REVISION_##_ver)

#define DWC3_VER_IS_WITHIN(_ip, _from, _to)                             \
        (DWC3_IP_IS(_ip) &&                                             \
         dwc->revision >= _ip##_REVISION_##_from &&                     \
         (!(_ip##_REVISION_##_to) ||                                    \
          dwc->revision <= _ip##_REVISION_##_to))

#define DWC3_VER_TYPE_IS_WITHIN(_ip, _ver, _from, _to)                  \
        (DWC3_VER_IS(_ip, _ver) &&                                      \
         dwc->version_type >= _ip##_VERSIONTYPE_##_from &&              \
         (!(_ip##_VERSIONTYPE_##_to) ||                                 \
          dwc->version_type <= _ip##_VERSIONTYPE_##_to))

/**
 * dwc3_mdwidth - get MDWIDTH value in bits
 * @dwc: pointer to our context structure
 *
 * Return MDWIDTH configuration value in bits.
 */
static inline u32 dwc3_mdwidth(struct dwc3 *dwc)
{
        u32 mdwidth;

        mdwidth = DWC3_GHWPARAMS0_MDWIDTH(dwc->hwparams.hwparams0);
        if (DWC3_IP_IS(DWC32))
                mdwidth += DWC3_GHWPARAMS6_MDWIDTH(dwc->hwparams.hwparams6);

        return mdwidth;
}

bool dwc3_has_imod(struct dwc3 *dwc);

int dwc3_event_buffers_setup(struct dwc3 *dwc);
void dwc3_event_buffers_cleanup(struct dwc3 *dwc);

int dwc3_core_soft_reset(struct dwc3 *dwc);
void dwc3_enable_susphy(struct dwc3 *dwc, bool enable);

#if IS_ENABLED(CONFIG_USB_DWC3_HOST) || IS_ENABLED(CONFIG_USB_DWC3_DUAL_ROLE)
int dwc3_host_init(struct dwc3 *dwc);
void dwc3_host_exit(struct dwc3 *dwc);
#else
static inline int dwc3_host_init(struct dwc3 *dwc)
{ return 0; }
static inline void dwc3_host_exit(struct dwc3 *dwc)
{ }
#endif

#if IS_ENABLED(CONFIG_USB_DWC3_GADGET) || IS_ENABLED(CONFIG_USB_DWC3_DUAL_ROLE)
int dwc3_gadget_init(struct dwc3 *dwc);
void dwc3_gadget_exit(struct dwc3 *dwc);
int dwc3_gadget_set_test_mode(struct dwc3 *dwc, int mode);
int dwc3_gadget_get_link_state(struct dwc3 *dwc);
int dwc3_gadget_set_link_state(struct dwc3 *dwc, enum dwc3_link_state state);
int dwc3_send_gadget_ep_cmd(struct dwc3_ep *dep, unsigned int cmd,
                struct dwc3_gadget_ep_cmd_params *params);
int dwc3_send_gadget_generic_command(struct dwc3 *dwc, unsigned int cmd,
                u32 param);
void dwc3_gadget_clear_tx_fifos(struct dwc3 *dwc);
void dwc3_remove_requests(struct dwc3 *dwc, struct dwc3_ep *dep, int status);
#else
static inline int dwc3_gadget_init(struct dwc3 *dwc)
{ return 0; }
static inline void dwc3_gadget_exit(struct dwc3 *dwc)
{ }
static inline int dwc3_gadget_set_test_mode(struct dwc3 *dwc, int mode)
{ return 0; }
static inline int dwc3_gadget_get_link_state(struct dwc3 *dwc)
{ return 0; }
static inline int dwc3_gadget_set_link_state(struct dwc3 *dwc,
                enum dwc3_link_state state)
{ return 0; }

static inline int dwc3_send_gadget_ep_cmd(struct dwc3_ep *dep, unsigned int cmd,
                struct dwc3_gadget_ep_cmd_params *params)
{ return 0; }
static inline int dwc3_send_gadget_generic_command(struct dwc3 *dwc,
                int cmd, u32 param)
{ return 0; }
static inline void dwc3_gadget_clear_tx_fifos(struct dwc3 *dwc)
{ }
#endif

#if IS_ENABLED(CONFIG_USB_DWC3_DUAL_ROLE)
int dwc3_drd_init(struct dwc3 *dwc);
void dwc3_drd_exit(struct dwc3 *dwc);
void dwc3_otg_init(struct dwc3 *dwc);
void dwc3_otg_exit(struct dwc3 *dwc);
void dwc3_otg_update(struct dwc3 *dwc, bool ignore_idstatus);
void dwc3_otg_host_init(struct dwc3 *dwc);
#else
static inline int dwc3_drd_init(struct dwc3 *dwc)
{ return 0; }
static inline void dwc3_drd_exit(struct dwc3 *dwc)
{ }
static inline void dwc3_otg_init(struct dwc3 *dwc)
{ }
static inline void dwc3_otg_exit(struct dwc3 *dwc)
{ }
static inline void dwc3_otg_update(struct dwc3 *dwc, bool ignore_idstatus)
{ }
static inline void dwc3_otg_host_init(struct dwc3 *dwc)
{ }
#endif

/* power management interface */
#if !IS_ENABLED(CONFIG_USB_DWC3_HOST)
int dwc3_gadget_suspend(struct dwc3 *dwc);
int dwc3_gadget_resume(struct dwc3 *dwc);
void dwc3_gadget_process_pending_events(struct dwc3 *dwc);
#else
static inline int dwc3_gadget_suspend(struct dwc3 *dwc)
{
        return 0;
}

static inline int dwc3_gadget_resume(struct dwc3 *dwc)
{
        return 0;
}

static inline void dwc3_gadget_process_pending_events(struct dwc3 *dwc)
{
}
#endif /* !IS_ENABLED(CONFIG_USB_DWC3_HOST) */

#if IS_ENABLED(CONFIG_USB_DWC3_ULPI)
int dwc3_ulpi_init(struct dwc3 *dwc);
void dwc3_ulpi_exit(struct dwc3 *dwc);
#else
static inline int dwc3_ulpi_init(struct dwc3 *dwc)
{ return 0; }
static inline void dwc3_ulpi_exit(struct dwc3 *dwc)
{ }
#endif

#endif /* __DRIVERS_USB_DWC3_CORE_H */