drivers/usb/host/xhci-rcar.c

   1 /*
   2  * xHCI host controller driver for R-Car SoCs
   3  *
   4  * Copyright (C) 2014 Renesas Electronics Corporation
   5  *
   6  * This program is free software; you can redistribute it and/or
   7  * modify it under the terms of the GNU General Public License
   8  * version 2 as published by the Free Software Foundation.
   9  */
  10
  11 #include <linux/firmware.h>
  12 #include <linux/module.h>
  13 #include <linux/platform_device.h>
  14 #include <linux/usb/phy.h>
  15
  16 #include "xhci.h"
  17 #include "xhci-plat.h"
  18 #include "xhci-rcar.h"
  19
  20 /*
  21 * - The V2 firmware is possible to use on R-Car Gen2. However, the V2 causes
  22 *   performance degradation. So, this driver continues to use the V1 if R-Car
  23 *   Gen2.
  24 * - The V1 firmware is impossible to use on R-Car Gen3.
  25 */
  26 MODULE_FIRMWARE(XHCI_RCAR_FIRMWARE_NAME_V1);
  27 MODULE_FIRMWARE(XHCI_RCAR_FIRMWARE_NAME_V2);
  28
  29 /*** Register Offset ***/
  30 #define RCAR_USB3_INT_ENA       0x224   /* Interrupt Enable */
  31 #define RCAR_USB3_DL_CTRL       0x250   /* FW Download Control & Status */
  32 #define RCAR_USB3_FW_DATA0      0x258   /* FW Data0 */
  33
  34 #define RCAR_USB3_LCLK          0xa44   /* LCLK Select */
  35 #define RCAR_USB3_CONF1         0xa48   /* USB3.0 Configuration1 */
  36 #define RCAR_USB3_CONF2         0xa5c   /* USB3.0 Configuration2 */
  37 #define RCAR_USB3_CONF3         0xaa8   /* USB3.0 Configuration3 */
  38 #define RCAR_USB3_RX_POL        0xab0   /* USB3.0 RX Polarity */
  39 #define RCAR_USB3_TX_POL        0xab8   /* USB3.0 TX Polarity */
  40
  41 /*** Register Settings ***/
  42 /* Interrupt Enable */
  43 #define RCAR_USB3_INT_XHC_ENA   0x00000001
  44 #define RCAR_USB3_INT_PME_ENA   0x00000002
  45 #define RCAR_USB3_INT_HSE_ENA   0x00000004
  46 #define RCAR_USB3_INT_ENA_VAL   (RCAR_USB3_INT_XHC_ENA | \
  47                                 RCAR_USB3_INT_PME_ENA | RCAR_USB3_INT_HSE_ENA)
  48
  49 /* FW Download Control & Status */
  50 #define RCAR_USB3_DL_CTRL_ENABLE        0x00000001
  51 #define RCAR_USB3_DL_CTRL_FW_SUCCESS    0x00000010
  52 #define RCAR_USB3_DL_CTRL_FW_SET_DATA0  0x00000100
  53
  54 /* LCLK Select */
  55 #define RCAR_USB3_LCLK_ENA_VAL  0x01030001
  56
  57 /* USB3.0 Configuration */
  58 #define RCAR_USB3_CONF1_VAL     0x00030204
  59 #define RCAR_USB3_CONF2_VAL     0x00030300
  60 #define RCAR_USB3_CONF3_VAL     0x13802007
  61
  62 /* USB3.0 Polarity */
  63 #define RCAR_USB3_RX_POL_VAL    BIT(21)
  64 #define RCAR_USB3_TX_POL_VAL    BIT(4)
  65
  66 static void xhci_rcar_start_gen2(struct usb_hcd *hcd)
  67 {
  68         /* LCLK Select */
  69         writel(RCAR_USB3_LCLK_ENA_VAL, hcd->regs + RCAR_USB3_LCLK);
  70         /* USB3.0 Configuration */
  71         writel(RCAR_USB3_CONF1_VAL, hcd->regs + RCAR_USB3_CONF1);
  72         writel(RCAR_USB3_CONF2_VAL, hcd->regs + RCAR_USB3_CONF2);
  73         writel(RCAR_USB3_CONF3_VAL, hcd->regs + RCAR_USB3_CONF3);
  74         /* USB3.0 Polarity */
  75         writel(RCAR_USB3_RX_POL_VAL, hcd->regs + RCAR_USB3_RX_POL);
  76         writel(RCAR_USB3_TX_POL_VAL, hcd->regs + RCAR_USB3_TX_POL);
  77 }
  78
  79 void xhci_rcar_start(struct usb_hcd *hcd)
  80 {
  81         u32 temp;
  82
  83         if (hcd->regs != NULL) {
  84                 /* Interrupt Enable */
  85                 temp = readl(hcd->regs + RCAR_USB3_INT_ENA);
  86                 temp |= RCAR_USB3_INT_ENA_VAL;
  87                 writel(temp, hcd->regs + RCAR_USB3_INT_ENA);
  88                 if (xhci_plat_type_is(hcd, XHCI_PLAT_TYPE_RENESAS_RCAR_GEN2))
  89                         xhci_rcar_start_gen2(hcd);
  90         }
  91 }
  92
  93 static int xhci_rcar_download_firmware(struct usb_hcd *hcd)
  94 {
  95         struct device *dev = hcd->self.controller;
  96         void __iomem *regs = hcd->regs;
  97         struct xhci_plat_priv *priv = hcd_to_xhci_priv(hcd);
  98         const struct firmware *fw;
  99         int retval, index, j, time;
 100         int timeout = 10000;
 101         u32 data, val, temp;
 102
 103         /* request R-Car USB3.0 firmware */
 104         retval = request_firmware(&fw, priv->firmware_name, dev);
 105         if (retval)
 106                 return retval;
 107
 108         /* download R-Car USB3.0 firmware */
 109         temp = readl(regs + RCAR_USB3_DL_CTRL);
 110         temp |= RCAR_USB3_DL_CTRL_ENABLE;
 111         writel(temp, regs + RCAR_USB3_DL_CTRL);
 112
 113         for (index = 0; index < fw->size; index += 4) {
 114                 /* to avoid reading beyond the end of the buffer */
 115                 for (data = 0, j = 3; j >= 0; j--) {
 116                         if ((j + index) < fw->size)
 117                                 data |= fw->data[index + j] << (8 * j);
 118                 }
 119                 writel(data, regs + RCAR_USB3_FW_DATA0);
 120                 temp = readl(regs + RCAR_USB3_DL_CTRL);
 121                 temp |= RCAR_USB3_DL_CTRL_FW_SET_DATA0;
 122                 writel(temp, regs + RCAR_USB3_DL_CTRL);
 123
 124                 for (time = 0; time < timeout; time++) {
 125                         val = readl(regs + RCAR_USB3_DL_CTRL);
 126                         if ((val & RCAR_USB3_DL_CTRL_FW_SET_DATA0) == 0)
 127                                 break;
 128                         udelay(1);
 129                 }
 130                 if (time == timeout) {
 131                         retval = -ETIMEDOUT;
 132                         break;
 133                 }
 134         }
 135
 136         temp = readl(regs + RCAR_USB3_DL_CTRL);
 137         temp &= ~RCAR_USB3_DL_CTRL_ENABLE;
 138         writel(temp, regs + RCAR_USB3_DL_CTRL);
 139
 140         for (time = 0; time < timeout; time++) {
 141                 val = readl(regs + RCAR_USB3_DL_CTRL);
 142                 if (val & RCAR_USB3_DL_CTRL_FW_SUCCESS) {
 143                         retval = 0;
 144                         break;
 145                 }
 146                 udelay(1);
 147         }
 148         if (time == timeout)
 149                 retval = -ETIMEDOUT;
 150
 151         release_firmware(fw);
 152
 153         return retval;
 154 }
 155
 156 /* This function needs to initialize a "phy" of usb before */
 157 int xhci_rcar_init_quirk(struct usb_hcd *hcd)
 158 {
 159         /* If hcd->regs is NULL, we don't just call the following function */
 160         if (!hcd->regs)
 161                 return 0;
 162
 163         return xhci_rcar_download_firmware(hcd);
 164 }