drivers/mmc/host/sdhci.c

   1 // SPDX-License-Identifier: GPL-2.0-or-later
   2 /*
   3  *  linux/drivers/mmc/host/sdhci.c - Secure Digital Host Controller Interface driver
   4  *
   5  *  Copyright (C) 2005-2008 Pierre Ossman, All Rights Reserved.
   6  *
   7  * Thanks to the following companies for their support:
   8  *
   9  *     - JMicron (hardware and technical support)
  10  */
  11
  12 #include <linux/delay.h>
  13 #include <linux/ktime.h>
  14 #include <linux/highmem.h>
  15 #include <linux/io.h>
  16 #include <linux/module.h>
  17 #include <linux/dma-mapping.h>
  18 #include <linux/slab.h>
  19 #include <linux/scatterlist.h>
  20 #include <linux/sizes.h>
  21 #include <linux/swiotlb.h>
  22 #include <linux/regulator/consumer.h>
  23 #include <linux/pm_runtime.h>
  24 #include <linux/of.h>
  25
  26 #include <linux/leds.h>
  27
  28 #include <linux/mmc/mmc.h>
  29 #include <linux/mmc/host.h>
  30 #include <linux/mmc/card.h>
  31 #include <linux/mmc/sdio.h>
  32 #include <linux/mmc/slot-gpio.h>
  33
  34 #include "sdhci.h"
  35
  36 #define DRIVER_NAME "sdhci"
  37
  38 #define DBG(f, x...) \
  39         pr_debug("%s: " DRIVER_NAME ": " f, mmc_hostname(host->mmc), ## x)
  40
  41 #define SDHCI_DUMP(f, x...) \
  42         pr_err("%s: " DRIVER_NAME ": " f, mmc_hostname(host->mmc), ## x)
  43
  44 #define MAX_TUNING_LOOP 40
  45
  46 static unsigned int debug_quirks = 0;
  47 static unsigned int debug_quirks2;
  48
  49 static void sdhci_finish_data(struct sdhci_host *);
  50
  51 static void sdhci_enable_preset_value(struct sdhci_host *host, bool enable);
  52
  53 void sdhci_dumpregs(struct sdhci_host *host)
  54 {
  55         SDHCI_DUMP("============ SDHCI REGISTER DUMP ===========\n");
  56
  57         SDHCI_DUMP("Sys addr:  0x%08x | Version:  0x%08x\n",
  58                    sdhci_readl(host, SDHCI_DMA_ADDRESS),
  59                    sdhci_readw(host, SDHCI_HOST_VERSION));
  60         SDHCI_DUMP("Blk size:  0x%08x | Blk cnt:  0x%08x\n",
  61                    sdhci_readw(host, SDHCI_BLOCK_SIZE),
  62                    sdhci_readw(host, SDHCI_BLOCK_COUNT));
  63         SDHCI_DUMP("Argument:  0x%08x | Trn mode: 0x%08x\n",
  64                    sdhci_readl(host, SDHCI_ARGUMENT),
  65                    sdhci_readw(host, SDHCI_TRANSFER_MODE));
  66         SDHCI_DUMP("Present:   0x%08x | Host ctl: 0x%08x\n",
  67                    sdhci_readl(host, SDHCI_PRESENT_STATE),
  68                    sdhci_readb(host, SDHCI_HOST_CONTROL));
  69         SDHCI_DUMP("Power:     0x%08x | Blk gap:  0x%08x\n",
  70                    sdhci_readb(host, SDHCI_POWER_CONTROL),
  71                    sdhci_readb(host, SDHCI_BLOCK_GAP_CONTROL));
  72         SDHCI_DUMP("Wake-up:   0x%08x | Clock:    0x%08x\n",
  73                    sdhci_readb(host, SDHCI_WAKE_UP_CONTROL),
  74                    sdhci_readw(host, SDHCI_CLOCK_CONTROL));
  75         SDHCI_DUMP("Timeout:   0x%08x | Int stat: 0x%08x\n",
  76                    sdhci_readb(host, SDHCI_TIMEOUT_CONTROL),
  77                    sdhci_readl(host, SDHCI_INT_STATUS));
  78         SDHCI_DUMP("Int enab:  0x%08x | Sig enab: 0x%08x\n",
  79                    sdhci_readl(host, SDHCI_INT_ENABLE),
  80                    sdhci_readl(host, SDHCI_SIGNAL_ENABLE));
  81         SDHCI_DUMP("ACmd stat: 0x%08x | Slot int: 0x%08x\n",
  82                    sdhci_readw(host, SDHCI_AUTO_CMD_STATUS),
  83                    sdhci_readw(host, SDHCI_SLOT_INT_STATUS));
  84         SDHCI_DUMP("Caps:      0x%08x | Caps_1:   0x%08x\n",
  85                    sdhci_readl(host, SDHCI_CAPABILITIES),
  86                    sdhci_readl(host, SDHCI_CAPABILITIES_1));
  87         SDHCI_DUMP("Cmd:       0x%08x | Max curr: 0x%08x\n",
  88                    sdhci_readw(host, SDHCI_COMMAND),
  89                    sdhci_readl(host, SDHCI_MAX_CURRENT));
  90         SDHCI_DUMP("Resp[0]:   0x%08x | Resp[1]:  0x%08x\n",
  91                    sdhci_readl(host, SDHCI_RESPONSE),
  92                    sdhci_readl(host, SDHCI_RESPONSE + 4));
  93         SDHCI_DUMP("Resp[2]:   0x%08x | Resp[3]:  0x%08x\n",
  94                    sdhci_readl(host, SDHCI_RESPONSE + 8),
  95                    sdhci_readl(host, SDHCI_RESPONSE + 12));
  96         SDHCI_DUMP("Host ctl2: 0x%08x\n",
  97                    sdhci_readw(host, SDHCI_HOST_CONTROL2));
  98
  99         if (host->flags & SDHCI_USE_ADMA) {
 100                 if (host->flags & SDHCI_USE_64_BIT_DMA) {
 101                         SDHCI_DUMP("ADMA Err:  0x%08x | ADMA Ptr: 0x%08x%08x\n",
 102                                    sdhci_readl(host, SDHCI_ADMA_ERROR),
 103                                    sdhci_readl(host, SDHCI_ADMA_ADDRESS_HI),
 104                                    sdhci_readl(host, SDHCI_ADMA_ADDRESS));
 105                 } else {
 106                         SDHCI_DUMP("ADMA Err:  0x%08x | ADMA Ptr: 0x%08x\n",
 107                                    sdhci_readl(host, SDHCI_ADMA_ERROR),
 108                                    sdhci_readl(host, SDHCI_ADMA_ADDRESS));
 109                 }
 110         }
 111
 112         SDHCI_DUMP("============================================\n");
 113 }
 114 EXPORT_SYMBOL_GPL(sdhci_dumpregs);
 115
 116 /*****************************************************************************\
 117  *                                                                           *
 118  * Low level functions                                                       *
 119  *                                                                           *
 120 \*****************************************************************************/
 121
 122 static void sdhci_do_enable_v4_mode(struct sdhci_host *host)
 123 {
 124         u16 ctrl2;
 125
 126         ctrl2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
 127         if (ctrl2 & SDHCI_CTRL_V4_MODE)
 128                 return;
 129
 130         ctrl2 |= SDHCI_CTRL_V4_MODE;
 131         sdhci_writew(host, ctrl2, SDHCI_HOST_CONTROL2);
 132 }
 133
 134 /*
 135  * This can be called before sdhci_add_host() by Vendor's host controller
 136  * driver to enable v4 mode if supported.
 137  */
 138 void sdhci_enable_v4_mode(struct sdhci_host *host)
 139 {
 140         host->v4_mode = true;
 141         sdhci_do_enable_v4_mode(host);
 142 }
 143 EXPORT_SYMBOL_GPL(sdhci_enable_v4_mode);
 144
 145 static inline bool sdhci_data_line_cmd(struct mmc_command *cmd)
 146 {
 147         return cmd->data || cmd->flags & MMC_RSP_BUSY;
 148 }
 149
 150 static void sdhci_set_card_detection(struct sdhci_host *host, bool enable)
 151 {
 152         u32 present;
 153
 154         if ((host->quirks & SDHCI_QUIRK_BROKEN_CARD_DETECTION) ||
 155             !mmc_card_is_removable(host->mmc))
 156                 return;
 157
 158         if (enable) {
 159                 present = sdhci_readl(host, SDHCI_PRESENT_STATE) &
 160                                       SDHCI_CARD_PRESENT;
 161
 162                 host->ier |= present ? SDHCI_INT_CARD_REMOVE :
 163                                        SDHCI_INT_CARD_INSERT;
 164         } else {
 165                 host->ier &= ~(SDHCI_INT_CARD_REMOVE | SDHCI_INT_CARD_INSERT);
 166         }
 167
 168         sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
 169         sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
 170 }
 171
 172 static void sdhci_enable_card_detection(struct sdhci_host *host)
 173 {
 174         sdhci_set_card_detection(host, true);
 175 }
 176
 177 static void sdhci_disable_card_detection(struct sdhci_host *host)
 178 {
 179         sdhci_set_card_detection(host, false);
 180 }
 181
 182 static void sdhci_runtime_pm_bus_on(struct sdhci_host *host)
 183 {
 184         if (host->bus_on)
 185                 return;
 186         host->bus_on = true;
 187         pm_runtime_get_noresume(host->mmc->parent);
 188 }
 189
 190 static void sdhci_runtime_pm_bus_off(struct sdhci_host *host)
 191 {
 192         if (!host->bus_on)
 193                 return;
 194         host->bus_on = false;
 195         pm_runtime_put_noidle(host->mmc->parent);
 196 }
 197
 198 void sdhci_reset(struct sdhci_host *host, u8 mask)
 199 {
 200         ktime_t timeout;
 201
 202         sdhci_writeb(host, mask, SDHCI_SOFTWARE_RESET);
 203
 204         if (mask & SDHCI_RESET_ALL) {
 205                 host->clock = 0;
 206                 /* Reset-all turns off SD Bus Power */
 207                 if (host->quirks2 & SDHCI_QUIRK2_CARD_ON_NEEDS_BUS_ON)
 208                         sdhci_runtime_pm_bus_off(host);
 209         }
 210
 211         /* Wait max 100 ms */
 212         timeout = ktime_add_ms(ktime_get(), 100);
 213
 214         /* hw clears the bit when it's done */
 215         while (1) {
 216                 bool timedout = ktime_after(ktime_get(), timeout);
 217
 218                 if (!(sdhci_readb(host, SDHCI_SOFTWARE_RESET) & mask))
 219                         break;
 220                 if (timedout) {
 221                         pr_err("%s: Reset 0x%x never completed.\n",
 222                                 mmc_hostname(host->mmc), (int)mask);
 223                         sdhci_dumpregs(host);
 224                         return;
 225                 }
 226                 udelay(10);
 227         }
 228 }
 229 EXPORT_SYMBOL_GPL(sdhci_reset);
 230
 231 static void sdhci_do_reset(struct sdhci_host *host, u8 mask)
 232 {
 233         if (host->quirks & SDHCI_QUIRK_NO_CARD_NO_RESET) {
 234                 struct mmc_host *mmc = host->mmc;
 235
 236                 if (!mmc->ops->get_cd(mmc))
 237                         return;
 238         }
 239
 240         host->ops->reset(host, mask);
 241
 242         if (mask & SDHCI_RESET_ALL) {
 243                 if (host->flags & (SDHCI_USE_SDMA | SDHCI_USE_ADMA)) {
 244                         if (host->ops->enable_dma)
 245                                 host->ops->enable_dma(host);
 246                 }
 247
 248                 /* Resetting the controller clears many */
 249                 host->preset_enabled = false;
 250         }
 251 }
 252
 253 static void sdhci_set_default_irqs(struct sdhci_host *host)
 254 {
 255         host->ier = SDHCI_INT_BUS_POWER | SDHCI_INT_DATA_END_BIT |
 256                     SDHCI_INT_DATA_CRC | SDHCI_INT_DATA_TIMEOUT |
 257                     SDHCI_INT_INDEX | SDHCI_INT_END_BIT | SDHCI_INT_CRC |
 258                     SDHCI_INT_TIMEOUT | SDHCI_INT_DATA_END |
 259                     SDHCI_INT_RESPONSE;
 260
 261         if (host->tuning_mode == SDHCI_TUNING_MODE_2 ||
 262             host->tuning_mode == SDHCI_TUNING_MODE_3)
 263                 host->ier |= SDHCI_INT_RETUNE;
 264
 265         sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
 266         sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
 267 }
 268
 269 static void sdhci_config_dma(struct sdhci_host *host)
 270 {
 271         u8 ctrl;
 272         u16 ctrl2;
 273
 274         if (host->version < SDHCI_SPEC_200)
 275                 return;
 276
 277         ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
 278
 279         /*
 280          * Always adjust the DMA selection as some controllers
 281          * (e.g. JMicron) can't do PIO properly when the selection
 282          * is ADMA.
 283          */
 284         ctrl &= ~SDHCI_CTRL_DMA_MASK;
 285         if (!(host->flags & SDHCI_REQ_USE_DMA))
 286                 goto out;
 287
 288         /* Note if DMA Select is zero then SDMA is selected */
 289         if (host->flags & SDHCI_USE_ADMA)
 290                 ctrl |= SDHCI_CTRL_ADMA32;
 291
 292         if (host->flags & SDHCI_USE_64_BIT_DMA) {
 293                 /*
 294                  * If v4 mode, all supported DMA can be 64-bit addressing if
 295                  * controller supports 64-bit system address, otherwise only
 296                  * ADMA can support 64-bit addressing.
 297                  */
 298                 if (host->v4_mode) {
 299                         ctrl2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
 300                         ctrl2 |= SDHCI_CTRL_64BIT_ADDR;
 301                         sdhci_writew(host, ctrl2, SDHCI_HOST_CONTROL2);
 302                 } else if (host->flags & SDHCI_USE_ADMA) {
 303                         /*
 304                          * Don't need to undo SDHCI_CTRL_ADMA32 in order to
 305                          * set SDHCI_CTRL_ADMA64.
 306                          */
 307                         ctrl |= SDHCI_CTRL_ADMA64;
 308                 }
 309         }
 310
 311 out:
 312         sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
 313 }
 314
 315 static void sdhci_init(struct sdhci_host *host, int soft)
 316 {
 317         struct mmc_host *mmc = host->mmc;
 318
 319         if (soft)
 320                 sdhci_do_reset(host, SDHCI_RESET_CMD | SDHCI_RESET_DATA);
 321         else
 322                 sdhci_do_reset(host, SDHCI_RESET_ALL);
 323
 324         if (host->v4_mode)
 325                 sdhci_do_enable_v4_mode(host);
 326
 327         sdhci_set_default_irqs(host);
 328
 329         host->cqe_on = false;
 330
 331         if (soft) {
 332                 /* force clock reconfiguration */
 333                 host->clock = 0;
 334                 mmc->ops->set_ios(mmc, &mmc->ios);
 335         }
 336 }
 337
 338 static void sdhci_reinit(struct sdhci_host *host)
 339 {
 340         sdhci_init(host, 0);
 341         sdhci_enable_card_detection(host);
 342 }
 343
 344 static void __sdhci_led_activate(struct sdhci_host *host)
 345 {
 346         u8 ctrl;
 347
 348         if (host->quirks & SDHCI_QUIRK_NO_LED)
 349                 return;
 350
 351         ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
 352         ctrl |= SDHCI_CTRL_LED;
 353         sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
 354 }
 355
 356 static void __sdhci_led_deactivate(struct sdhci_host *host)
 357 {
 358         u8 ctrl;
 359
 360         if (host->quirks & SDHCI_QUIRK_NO_LED)
 361                 return;
 362
 363         ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
 364         ctrl &= ~SDHCI_CTRL_LED;
 365         sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
 366 }
 367
 368 #if IS_REACHABLE(CONFIG_LEDS_CLASS)
 369 static void sdhci_led_control(struct led_classdev *led,
 370                               enum led_brightness brightness)
 371 {
 372         struct sdhci_host *host = container_of(led, struct sdhci_host, led);
 373         unsigned long flags;
 374
 375         spin_lock_irqsave(&host->lock, flags);
 376
 377         if (host->runtime_suspended)
 378                 goto out;
 379
 380         if (brightness == LED_OFF)
 381                 __sdhci_led_deactivate(host);
 382         else
 383                 __sdhci_led_activate(host);
 384 out:
 385         spin_unlock_irqrestore(&host->lock, flags);
 386 }
 387
 388 static int sdhci_led_register(struct sdhci_host *host)
 389 {
 390         struct mmc_host *mmc = host->mmc;
 391
 392         if (host->quirks & SDHCI_QUIRK_NO_LED)
 393                 return 0;
 394
 395         snprintf(host->led_name, sizeof(host->led_name),
 396                  "%s::", mmc_hostname(mmc));
 397
 398         host->led.name = host->led_name;
 399         host->led.brightness = LED_OFF;
 400         host->led.default_trigger = mmc_hostname(mmc);
 401         host->led.brightness_set = sdhci_led_control;
 402
 403         return led_classdev_register(mmc_dev(mmc), &host->led);
 404 }
 405
 406 static void sdhci_led_unregister(struct sdhci_host *host)
 407 {
 408         if (host->quirks & SDHCI_QUIRK_NO_LED)
 409                 return;
 410
 411         led_classdev_unregister(&host->led);
 412 }
 413
 414 static inline void sdhci_led_activate(struct sdhci_host *host)
 415 {
 416 }
 417
 418 static inline void sdhci_led_deactivate(struct sdhci_host *host)
 419 {
 420 }
 421
 422 #else
 423
 424 static inline int sdhci_led_register(struct sdhci_host *host)
 425 {
 426         return 0;
 427 }
 428
 429 static inline void sdhci_led_unregister(struct sdhci_host *host)
 430 {
 431 }
 432
 433 static inline void sdhci_led_activate(struct sdhci_host *host)
 434 {
 435         __sdhci_led_activate(host);
 436 }
 437
 438 static inline void sdhci_led_deactivate(struct sdhci_host *host)
 439 {
 440         __sdhci_led_deactivate(host);
 441 }
 442
 443 #endif
 444
 445 static void sdhci_mod_timer(struct sdhci_host *host, struct mmc_request *mrq,
 446                             unsigned long timeout)
 447 {
 448         if (sdhci_data_line_cmd(mrq->cmd))
 449                 mod_timer(&host->data_timer, timeout);
 450         else
 451                 mod_timer(&host->timer, timeout);
 452 }
 453
 454 static void sdhci_del_timer(struct sdhci_host *host, struct mmc_request *mrq)
 455 {
 456         if (sdhci_data_line_cmd(mrq->cmd))
 457                 del_timer(&host->data_timer);
 458         else
 459                 del_timer(&host->timer);
 460 }
 461
 462 static inline bool sdhci_has_requests(struct sdhci_host *host)
 463 {
 464         return host->cmd || host->data_cmd;
 465 }
 466
 467 /*****************************************************************************\
 468  *                                                                           *
 469  * Core functions                                                            *
 470  *                                                                           *
 471 \*****************************************************************************/
 472
 473 static void sdhci_read_block_pio(struct sdhci_host *host)
 474 {
 475         unsigned long flags;
 476         size_t blksize, len, chunk;
 477         u32 uninitialized_var(scratch);
 478         u8 *buf;
 479
 480         DBG("PIO reading\n");
 481
 482         blksize = host->data->blksz;
 483         chunk = 0;
 484
 485         local_irq_save(flags);
 486
 487         while (blksize) {
 488                 BUG_ON(!sg_miter_next(&host->sg_miter));
 489
 490                 len = min(host->sg_miter.length, blksize);
 491
 492                 blksize -= len;
 493                 host->sg_miter.consumed = len;
 494
 495                 buf = host->sg_miter.addr;
 496
 497                 while (len) {
 498                         if (chunk == 0) {
 499                                 scratch = sdhci_readl(host, SDHCI_BUFFER);
 500                                 chunk = 4;
 501                         }
 502
 503                         *buf = scratch & 0xFF;
 504
 505                         buf++;
 506                         scratch >>= 8;
 507                         chunk--;
 508                         len--;
 509                 }
 510         }
 511
 512         sg_miter_stop(&host->sg_miter);
 513
 514         local_irq_restore(flags);
 515 }
 516
 517 static void sdhci_write_block_pio(struct sdhci_host *host)
 518 {
 519         unsigned long flags;
 520         size_t blksize, len, chunk;
 521         u32 scratch;
 522         u8 *buf;
 523
 524         DBG("PIO writing\n");
 525
 526         blksize = host->data->blksz;
 527         chunk = 0;
 528         scratch = 0;
 529
 530         local_irq_save(flags);
 531
 532         while (blksize) {
 533                 BUG_ON(!sg_miter_next(&host->sg_miter));
 534
 535                 len = min(host->sg_miter.length, blksize);
 536
 537                 blksize -= len;
 538                 host->sg_miter.consumed = len;
 539
 540                 buf = host->sg_miter.addr;
 541
 542                 while (len) {
 543                         scratch |= (u32)*buf << (chunk * 8);
 544
 545                         buf++;
 546                         chunk++;
 547                         len--;
 548
 549                         if ((chunk == 4) || ((len == 0) && (blksize == 0))) {
 550                                 sdhci_writel(host, scratch, SDHCI_BUFFER);
 551                                 chunk = 0;
 552                                 scratch = 0;
 553                         }
 554                 }
 555         }
 556
 557         sg_miter_stop(&host->sg_miter);
 558
 559         local_irq_restore(flags);
 560 }
 561
 562 static void sdhci_transfer_pio(struct sdhci_host *host)
 563 {
 564         u32 mask;
 565
 566         if (host->blocks == 0)
 567                 return;
 568
 569         if (host->data->flags & MMC_DATA_READ)
 570                 mask = SDHCI_DATA_AVAILABLE;
 571         else
 572                 mask = SDHCI_SPACE_AVAILABLE;
 573
 574         /*
 575          * Some controllers (JMicron JMB38x) mess up the buffer bits
 576          * for transfers < 4 bytes. As long as it is just one block,
 577          * we can ignore the bits.
 578          */
 579         if ((host->quirks & SDHCI_QUIRK_BROKEN_SMALL_PIO) &&
 580                 (host->data->blocks == 1))
 581                 mask = ~0;
 582
 583         while (sdhci_readl(host, SDHCI_PRESENT_STATE) & mask) {
 584                 if (host->quirks & SDHCI_QUIRK_PIO_NEEDS_DELAY)
 585                         udelay(100);
 586
 587                 if (host->data->flags & MMC_DATA_READ)
 588                         sdhci_read_block_pio(host);
 589                 else
 590                         sdhci_write_block_pio(host);
 591
 592                 host->blocks--;
 593                 if (host->blocks == 0)
 594                         break;
 595         }
 596
 597         DBG("PIO transfer complete.\n");
 598 }
 599
 600 static int sdhci_pre_dma_transfer(struct sdhci_host *host,
 601                                   struct mmc_data *data, int cookie)
 602 {
 603         int sg_count;
 604
 605         /*
 606          * If the data buffers are already mapped, return the previous
 607          * dma_map_sg() result.
 608          */
 609         if (data->host_cookie == COOKIE_PRE_MAPPED)
 610                 return data->sg_count;
 611
 612         /* Bounce write requests to the bounce buffer */
 613         if (host->bounce_buffer) {
 614                 unsigned int length = data->blksz * data->blocks;
 615
 616                 if (length > host->bounce_buffer_size) {
 617                         pr_err("%s: asked for transfer of %u bytes exceeds bounce buffer %u bytes\n",
 618                                mmc_hostname(host->mmc), length,
 619                                host->bounce_buffer_size);
 620                         return -EIO;
 621                 }
 622                 if (mmc_get_dma_dir(data) == DMA_TO_DEVICE) {
 623                         /* Copy the data to the bounce buffer */
 624                         sg_copy_to_buffer(data->sg, data->sg_len,
 625                                           host->bounce_buffer,
 626                                           length);
 627                 }
 628                 /* Switch ownership to the DMA */
 629                 dma_sync_single_for_device(host->mmc->parent,
 630                                            host->bounce_addr,
 631                                            host->bounce_buffer_size,
 632                                            mmc_get_dma_dir(data));
 633                 /* Just a dummy value */
 634                 sg_count = 1;
 635         } else {
 636                 /* Just access the data directly from memory */
 637                 sg_count = dma_map_sg(mmc_dev(host->mmc),
 638                                       data->sg, data->sg_len,
 639                                       mmc_get_dma_dir(data));
 640         }
 641
 642         if (sg_count == 0)
 643                 return -ENOSPC;
 644
 645         data->sg_count = sg_count;
 646         data->host_cookie = cookie;
 647
 648         return sg_count;
 649 }
 650
 651 static char *sdhci_kmap_atomic(struct scatterlist *sg, unsigned long *flags)
 652 {
 653         local_irq_save(*flags);
 654         return kmap_atomic(sg_page(sg)) + sg->offset;
 655 }
 656
 657 static void sdhci_kunmap_atomic(void *buffer, unsigned long *flags)
 658 {
 659         kunmap_atomic(buffer);
 660         local_irq_restore(*flags);
 661 }
 662
 663 void sdhci_adma_write_desc(struct sdhci_host *host, void **desc,
 664                            dma_addr_t addr, int len, unsigned int cmd)
 665 {
 666         struct sdhci_adma2_64_desc *dma_desc = *desc;
 667
 668         /* 32-bit and 64-bit descriptors have these members in same position */
 669         dma_desc->cmd = cpu_to_le16(cmd);
 670         dma_desc->len = cpu_to_le16(len);
 671         dma_desc->addr_lo = cpu_to_le32(lower_32_bits(addr));
 672
 673         if (host->flags & SDHCI_USE_64_BIT_DMA)
 674                 dma_desc->addr_hi = cpu_to_le32(upper_32_bits(addr));
 675
 676         *desc += host->desc_sz;
 677 }
 678 EXPORT_SYMBOL_GPL(sdhci_adma_write_desc);
 679
 680 static inline void __sdhci_adma_write_desc(struct sdhci_host *host,
 681                                            void **desc, dma_addr_t addr,
 682                                            int len, unsigned int cmd)
 683 {
 684         if (host->ops->adma_write_desc)
 685                 host->ops->adma_write_desc(host, desc, addr, len, cmd);
 686         else
 687                 sdhci_adma_write_desc(host, desc, addr, len, cmd);
 688 }
 689
 690 static void sdhci_adma_mark_end(void *desc)
 691 {
 692         struct sdhci_adma2_64_desc *dma_desc = desc;
 693
 694         /* 32-bit and 64-bit descriptors have 'cmd' in same position */
 695         dma_desc->cmd |= cpu_to_le16(ADMA2_END);
 696 }
 697
 698 static void sdhci_adma_table_pre(struct sdhci_host *host,
 699         struct mmc_data *data, int sg_count)
 700 {
 701         struct scatterlist *sg;
 702         unsigned long flags;
 703         dma_addr_t addr, align_addr;
 704         void *desc, *align;
 705         char *buffer;
 706         int len, offset, i;
 707
 708         /*
 709          * The spec does not specify endianness of descriptor table.
 710          * We currently guess that it is LE.
 711          */
 712
 713         host->sg_count = sg_count;
 714
 715         desc = host->adma_table;
 716         align = host->align_buffer;
 717
 718         align_addr = host->align_addr;
 719
 720         for_each_sg(data->sg, sg, host->sg_count, i) {
 721                 addr = sg_dma_address(sg);
 722                 len = sg_dma_len(sg);
 723
 724                 /*
 725                  * The SDHCI specification states that ADMA addresses must
 726                  * be 32-bit aligned. If they aren't, then we use a bounce
 727                  * buffer for the (up to three) bytes that screw up the
 728                  * alignment.
 729                  */
 730                 offset = (SDHCI_ADMA2_ALIGN - (addr & SDHCI_ADMA2_MASK)) &
 731                          SDHCI_ADMA2_MASK;
 732                 if (offset) {
 733                         if (data->flags & MMC_DATA_WRITE) {
 734                                 buffer = sdhci_kmap_atomic(sg, &flags);
 735                                 memcpy(align, buffer, offset);
 736                                 sdhci_kunmap_atomic(buffer, &flags);
 737                         }
 738
 739                         /* tran, valid */
 740                         __sdhci_adma_write_desc(host, &desc, align_addr,
 741                                                 offset, ADMA2_TRAN_VALID);
 742
 743                         BUG_ON(offset > 65536);
 744
 745                         align += SDHCI_ADMA2_ALIGN;
 746                         align_addr += SDHCI_ADMA2_ALIGN;
 747
 748                         addr += offset;
 749                         len -= offset;
 750                 }
 751
 752                 BUG_ON(len > 65536);
 753
 754                 /* tran, valid */
 755                 if (len)
 756                         __sdhci_adma_write_desc(host, &desc, addr, len,
 757                                                 ADMA2_TRAN_VALID);
 758
 759                 /*
 760                  * If this triggers then we have a calculation bug
 761                  * somewhere. :/
 762                  */
 763                 WARN_ON((desc - host->adma_table) >= host->adma_table_sz);
 764         }
 765
 766         if (host->quirks & SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC) {
 767                 /* Mark the last descriptor as the terminating descriptor */
 768                 if (desc != host->adma_table) {
 769                         desc -= host->desc_sz;
 770                         sdhci_adma_mark_end(desc);
 771                 }
 772         } else {
 773                 /* Add a terminating entry - nop, end, valid */
 774                 __sdhci_adma_write_desc(host, &desc, 0, 0, ADMA2_NOP_END_VALID);
 775         }
 776 }
 777
 778 static void sdhci_adma_table_post(struct sdhci_host *host,
 779         struct mmc_data *data)
 780 {
 781         struct scatterlist *sg;
 782         int i, size;
 783         void *align;
 784         char *buffer;
 785         unsigned long flags;
 786
 787         if (data->flags & MMC_DATA_READ) {
 788                 bool has_unaligned = false;
 789
 790                 /* Do a quick scan of the SG list for any unaligned mappings */
 791                 for_each_sg(data->sg, sg, host->sg_count, i)
 792                         if (sg_dma_address(sg) & SDHCI_ADMA2_MASK) {
 793                                 has_unaligned = true;
 794                                 break;
 795                         }
 796
 797                 if (has_unaligned) {
 798                         dma_sync_sg_for_cpu(mmc_dev(host->mmc), data->sg,
 799                                             data->sg_len, DMA_FROM_DEVICE);
 800
 801                         align = host->align_buffer;
 802
 803                         for_each_sg(data->sg, sg, host->sg_count, i) {
 804                                 if (sg_dma_address(sg) & SDHCI_ADMA2_MASK) {
 805                                         size = SDHCI_ADMA2_ALIGN -
 806                                                (sg_dma_address(sg) & SDHCI_ADMA2_MASK);
 807
 808                                         buffer = sdhci_kmap_atomic(sg, &flags);
 809                                         memcpy(buffer, align, size);
 810                                         sdhci_kunmap_atomic(buffer, &flags);
 811
 812                                         align += SDHCI_ADMA2_ALIGN;
 813                                 }
 814                         }
 815                 }
 816         }
 817 }
 818
 819 static void sdhci_set_adma_addr(struct sdhci_host *host, dma_addr_t addr)
 820 {
 821         sdhci_writel(host, lower_32_bits(addr), SDHCI_ADMA_ADDRESS);
 822         if (host->flags & SDHCI_USE_64_BIT_DMA)
 823                 sdhci_writel(host, upper_32_bits(addr), SDHCI_ADMA_ADDRESS_HI);
 824 }
 825
 826 static dma_addr_t sdhci_sdma_address(struct sdhci_host *host)
 827 {
 828         if (host->bounce_buffer)
 829                 return host->bounce_addr;
 830         else
 831                 return sg_dma_address(host->data->sg);
 832 }
 833
 834 static void sdhci_set_sdma_addr(struct sdhci_host *host, dma_addr_t addr)
 835 {
 836         if (host->v4_mode)
 837                 sdhci_set_adma_addr(host, addr);
 838         else
 839                 sdhci_writel(host, addr, SDHCI_DMA_ADDRESS);
 840 }
 841
 842 static unsigned int sdhci_target_timeout(struct sdhci_host *host,
 843                                          struct mmc_command *cmd,
 844                                          struct mmc_data *data)
 845 {
 846         unsigned int target_timeout;
 847
 848         /* timeout in us */
 849         if (!data) {
 850                 target_timeout = cmd->busy_timeout * 1000;
 851         } else {
 852                 target_timeout = DIV_ROUND_UP(data->timeout_ns, 1000);
 853                 if (host->clock && data->timeout_clks) {
 854                         unsigned long long val;
 855
 856                         /*
 857                          * data->timeout_clks is in units of clock cycles.
 858                          * host->clock is in Hz.  target_timeout is in us.
 859                          * Hence, us = 1000000 * cycles / Hz.  Round up.
 860                          */
 861                         val = 1000000ULL * data->timeout_clks;
 862                         if (do_div(val, host->clock))
 863                                 target_timeout++;
 864                         target_timeout += val;
 865                 }
 866         }
 867
 868         return target_timeout;
 869 }
 870
 871 static void sdhci_calc_sw_timeout(struct sdhci_host *host,
 872                                   struct mmc_command *cmd)
 873 {
 874         struct mmc_data *data = cmd->data;
 875         struct mmc_host *mmc = host->mmc;
 876         struct mmc_ios *ios = &mmc->ios;
 877         unsigned char bus_width = 1 << ios->bus_width;
 878         unsigned int blksz;
 879         unsigned int freq;
 880         u64 target_timeout;
 881         u64 transfer_time;
 882
 883         target_timeout = sdhci_target_timeout(host, cmd, data);
 884         target_timeout *= NSEC_PER_USEC;
 885
 886         if (data) {
 887                 blksz = data->blksz;
 888                 freq = host->mmc->actual_clock ? : host->clock;
 889                 transfer_time = (u64)blksz * NSEC_PER_SEC * (8 / bus_width);
 890                 do_div(transfer_time, freq);
 891                 /* multiply by '2' to account for any unknowns */
 892                 transfer_time = transfer_time * 2;
 893                 /* calculate timeout for the entire data */
 894                 host->data_timeout = data->blocks * target_timeout +
 895                                      transfer_time;
 896         } else {
 897                 host->data_timeout = target_timeout;
 898         }
 899
 900         if (host->data_timeout)
 901                 host->data_timeout += MMC_CMD_TRANSFER_TIME;
 902 }
 903
 904 static u8 sdhci_calc_timeout(struct sdhci_host *host, struct mmc_command *cmd,
 905                              bool *too_big)
 906 {
 907         u8 count;
 908         struct mmc_data *data;
 909         unsigned target_timeout, current_timeout;
 910
 911         *too_big = true;
 912
 913         /*
 914          * If the host controller provides us with an incorrect timeout
 915          * value, just skip the check and use 0xE.  The hardware may take
 916          * longer to time out, but that's much better than having a too-short
 917          * timeout value.
 918          */
 919         if (host->quirks & SDHCI_QUIRK_BROKEN_TIMEOUT_VAL)
 920                 return 0xE;
 921
 922         /* Unspecified command, asume max */
 923         if (cmd == NULL)
 924                 return 0xE;
 925
 926         data = cmd->data;
 927         /* Unspecified timeout, assume max */
 928         if (!data && !cmd->busy_timeout)
 929                 return 0xE;
 930
 931         /* timeout in us */
 932         target_timeout = sdhci_target_timeout(host, cmd, data);
 933
 934         /*
 935          * Figure out needed cycles.
 936          * We do this in steps in order to fit inside a 32 bit int.
 937          * The first step is the minimum timeout, which will have a
 938          * minimum resolution of 6 bits:
 939          * (1) 2^13*1000 > 2^22,
 940          * (2) host->timeout_clk < 2^16
 941          *     =>
 942          *     (1) / (2) > 2^6
 943          */
 944         count = 0;
 945         current_timeout = (1 << 13) * 1000 / host->timeout_clk;
 946         while (current_timeout < target_timeout) {
 947                 count++;
 948                 current_timeout <<= 1;
 949                 if (count >= 0xF)
 950                         break;
 951         }
 952
 953         if (count >= 0xF) {
 954                 if (!(host->quirks2 & SDHCI_QUIRK2_DISABLE_HW_TIMEOUT))
 955                         DBG("Too large timeout 0x%x requested for CMD%d!\n",
 956                             count, cmd->opcode);
 957                 count = 0xE;
 958         } else {
 959                 *too_big = false;
 960         }
 961
 962         return count;
 963 }
 964
 965 static void sdhci_set_transfer_irqs(struct sdhci_host *host)
 966 {
 967         u32 pio_irqs = SDHCI_INT_DATA_AVAIL | SDHCI_INT_SPACE_AVAIL;
 968         u32 dma_irqs = SDHCI_INT_DMA_END | SDHCI_INT_ADMA_ERROR;
 969
 970         if (host->flags & SDHCI_REQ_USE_DMA)
 971                 host->ier = (host->ier & ~pio_irqs) | dma_irqs;
 972         else
 973                 host->ier = (host->ier & ~dma_irqs) | pio_irqs;
 974
 975         if (host->flags & (SDHCI_AUTO_CMD23 | SDHCI_AUTO_CMD12))
 976                 host->ier |= SDHCI_INT_AUTO_CMD_ERR;
 977         else
 978                 host->ier &= ~SDHCI_INT_AUTO_CMD_ERR;
 979
 980         sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
 981         sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
 982 }
 983
 984 static void sdhci_set_data_timeout_irq(struct sdhci_host *host, bool enable)
 985 {
 986         if (enable)
 987                 host->ier |= SDHCI_INT_DATA_TIMEOUT;
 988         else
 989                 host->ier &= ~SDHCI_INT_DATA_TIMEOUT;
 990         sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
 991         sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
 992 }
 993
 994 static void sdhci_set_timeout(struct sdhci_host *host, struct mmc_command *cmd)
 995 {
 996         u8 count;
 997
 998         if (host->ops->set_timeout) {
 999                 host->ops->set_timeout(host, cmd);
1000         } else {
1001                 bool too_big = false;
1002
1003                 count = sdhci_calc_timeout(host, cmd, &too_big);
1004
1005                 if (too_big &&
1006                     host->quirks2 & SDHCI_QUIRK2_DISABLE_HW_TIMEOUT) {
1007                         sdhci_calc_sw_timeout(host, cmd);
1008                         sdhci_set_data_timeout_irq(host, false);
1009                 } else if (!(host->ier & SDHCI_INT_DATA_TIMEOUT)) {
1010                         sdhci_set_data_timeout_irq(host, true);
1011                 }
1012
1013                 sdhci_writeb(host, count, SDHCI_TIMEOUT_CONTROL);
1014         }
1015 }
1016
1017 static void sdhci_prepare_data(struct sdhci_host *host, struct mmc_command *cmd)
1018 {
1019         struct mmc_data *data = cmd->data;
1020
1021         host->data_timeout = 0;
1022
1023         if (sdhci_data_line_cmd(cmd))
1024                 sdhci_set_timeout(host, cmd);
1025
1026         if (!data)
1027                 return;
1028
1029         WARN_ON(host->data);
1030
1031         /* Sanity checks */
1032         BUG_ON(data->blksz * data->blocks > 524288);
1033         BUG_ON(data->blksz > host->mmc->max_blk_size);
1034         BUG_ON(data->blocks > 65535);
1035
1036         host->data = data;
1037         host->data_early = 0;
1038         host->data->bytes_xfered = 0;
1039
1040         if (host->flags & (SDHCI_USE_SDMA | SDHCI_USE_ADMA)) {
1041                 struct scatterlist *sg;
1042                 unsigned int length_mask, offset_mask;
1043                 int i;
1044
1045                 host->flags |= SDHCI_REQ_USE_DMA;
1046
1047                 /*
1048                  * FIXME: This doesn't account for merging when mapping the
1049                  * scatterlist.
1050                  *
1051                  * The assumption here being that alignment and lengths are
1052                  * the same after DMA mapping to device address space.
1053                  */
1054                 length_mask = 0;
1055                 offset_mask = 0;
1056                 if (host->flags & SDHCI_USE_ADMA) {
1057                         if (host->quirks & SDHCI_QUIRK_32BIT_ADMA_SIZE) {
1058                                 length_mask = 3;
1059                                 /*
1060                                  * As we use up to 3 byte chunks to work
1061                                  * around alignment problems, we need to
1062                                  * check the offset as well.
1063                                  */
1064                                 offset_mask = 3;
1065                         }
1066                 } else {
1067                         if (host->quirks & SDHCI_QUIRK_32BIT_DMA_SIZE)
1068                                 length_mask = 3;
1069                         if (host->quirks & SDHCI_QUIRK_32BIT_DMA_ADDR)
1070                                 offset_mask = 3;
1071                 }
1072
1073                 if (unlikely(length_mask | offset_mask)) {
1074                         for_each_sg(data->sg, sg, data->sg_len, i) {
1075                                 if (sg->length & length_mask) {
1076                                         DBG("Reverting to PIO because of transfer size (%d)\n",
1077                                             sg->length);
1078                                         host->flags &= ~SDHCI_REQ_USE_DMA;
1079                                         break;
1080                                 }
1081                                 if (sg->offset & offset_mask) {
1082                                         DBG("Reverting to PIO because of bad alignment\n");
1083                                         host->flags &= ~SDHCI_REQ_USE_DMA;
1084                                         break;
1085                                 }
1086                         }
1087                 }
1088         }
1089
1090         if (host->flags & SDHCI_REQ_USE_DMA) {
1091                 int sg_cnt = sdhci_pre_dma_transfer(host, data, COOKIE_MAPPED);
1092
1093                 if (sg_cnt <= 0) {
1094                         /*
1095                          * This only happens when someone fed
1096                          * us an invalid request.
1097                          */
1098                         WARN_ON(1);
1099                         host->flags &= ~SDHCI_REQ_USE_DMA;
1100                 } else if (host->flags & SDHCI_USE_ADMA) {
1101                         sdhci_adma_table_pre(host, data, sg_cnt);
1102                         sdhci_set_adma_addr(host, host->adma_addr);
1103                 } else {
1104                         WARN_ON(sg_cnt != 1);
1105                         sdhci_set_sdma_addr(host, sdhci_sdma_address(host));
1106                 }
1107         }
1108
1109         sdhci_config_dma(host);
1110
1111         if (!(host->flags & SDHCI_REQ_USE_DMA)) {
1112                 int flags;
1113
1114                 flags = SG_MITER_ATOMIC;
1115                 if (host->data->flags & MMC_DATA_READ)
1116                         flags |= SG_MITER_TO_SG;
1117                 else
1118                         flags |= SG_MITER_FROM_SG;
1119                 sg_miter_start(&host->sg_miter, data->sg, data->sg_len, flags);
1120                 host->blocks = data->blocks;
1121         }
1122
1123         sdhci_set_transfer_irqs(host);
1124
1125         /* Set the DMA boundary value and block size */
1126         sdhci_writew(host, SDHCI_MAKE_BLKSZ(host->sdma_boundary, data->blksz),
1127                      SDHCI_BLOCK_SIZE);
1128
1129         /*
1130          * For Version 4.10 onwards, if v4 mode is enabled, 32-bit Block Count
1131          * can be supported, in that case 16-bit block count register must be 0.
1132          */
1133         if (host->version >= SDHCI_SPEC_410 && host->v4_mode &&
1134             (host->quirks2 & SDHCI_QUIRK2_USE_32BIT_BLK_CNT)) {
1135                 if (sdhci_readw(host, SDHCI_BLOCK_COUNT))
1136                         sdhci_writew(host, 0, SDHCI_BLOCK_COUNT);
1137                 sdhci_writew(host, data->blocks, SDHCI_32BIT_BLK_CNT);
1138         } else {
1139                 sdhci_writew(host, data->blocks, SDHCI_BLOCK_COUNT);
1140         }
1141 }
1142
1143 static inline bool sdhci_auto_cmd12(struct sdhci_host *host,
1144                                     struct mmc_request *mrq)
1145 {
1146         return !mrq->sbc && (host->flags & SDHCI_AUTO_CMD12) &&
1147                !mrq->cap_cmd_during_tfr;
1148 }
1149
1150 static inline void sdhci_auto_cmd_select(struct sdhci_host *host,
1151                                          struct mmc_command *cmd,
1152                                          u16 *mode)
1153 {
1154         bool use_cmd12 = sdhci_auto_cmd12(host, cmd->mrq) &&
1155                          (cmd->opcode != SD_IO_RW_EXTENDED);
1156         bool use_cmd23 = cmd->mrq->sbc && (host->flags & SDHCI_AUTO_CMD23);
1157         u16 ctrl2;
1158
1159         /*
1160          * In case of Version 4.10 or later, use of 'Auto CMD Auto
1161          * Select' is recommended rather than use of 'Auto CMD12
1162          * Enable' or 'Auto CMD23 Enable'.
1163          */
1164         if (host->version >= SDHCI_SPEC_410 && (use_cmd12 || use_cmd23)) {
1165                 *mode |= SDHCI_TRNS_AUTO_SEL;
1166
1167                 ctrl2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
1168                 if (use_cmd23)
1169                         ctrl2 |= SDHCI_CMD23_ENABLE;
1170                 else
1171                         ctrl2 &= ~SDHCI_CMD23_ENABLE;
1172                 sdhci_writew(host, ctrl2, SDHCI_HOST_CONTROL2);
1173
1174                 return;
1175         }
1176
1177         /*
1178          * If we are sending CMD23, CMD12 never gets sent
1179          * on successful completion (so no Auto-CMD12).
1180          */
1181         if (use_cmd12)
1182                 *mode |= SDHCI_TRNS_AUTO_CMD12;
1183         else if (use_cmd23)
1184                 *mode |= SDHCI_TRNS_AUTO_CMD23;
1185 }
1186
1187 static void sdhci_set_transfer_mode(struct sdhci_host *host,
1188         struct mmc_command *cmd)
1189 {
1190         u16 mode = 0;
1191         struct mmc_data *data = cmd->data;
1192
1193         if (data == NULL) {
1194                 if (host->quirks2 &
1195                         SDHCI_QUIRK2_CLEAR_TRANSFERMODE_REG_BEFORE_CMD) {
1196                         /* must not clear SDHCI_TRANSFER_MODE when tuning */
1197                         if (cmd->opcode != MMC_SEND_TUNING_BLOCK_HS200)
1198                                 sdhci_writew(host, 0x0, SDHCI_TRANSFER_MODE);
1199                 } else {
1200                 /* clear Auto CMD settings for no data CMDs */
1201                         mode = sdhci_readw(host, SDHCI_TRANSFER_MODE);
1202                         sdhci_writew(host, mode & ~(SDHCI_TRNS_AUTO_CMD12 |
1203                                 SDHCI_TRNS_AUTO_CMD23), SDHCI_TRANSFER_MODE);
1204                 }
1205                 return;
1206         }
1207
1208         WARN_ON(!host->data);
1209
1210         if (!(host->quirks2 & SDHCI_QUIRK2_SUPPORT_SINGLE))
1211                 mode = SDHCI_TRNS_BLK_CNT_EN;
1212
1213         if (mmc_op_multi(cmd->opcode) || data->blocks > 1) {
1214                 mode = SDHCI_TRNS_BLK_CNT_EN | SDHCI_TRNS_MULTI;
1215                 sdhci_auto_cmd_select(host, cmd, &mode);
1216                 if (cmd->mrq->sbc && (host->flags & SDHCI_AUTO_CMD23))
1217                         sdhci_writel(host, cmd->mrq->sbc->arg, SDHCI_ARGUMENT2);
1218         }
1219
1220         if (data->flags & MMC_DATA_READ)
1221                 mode |= SDHCI_TRNS_READ;
1222         if (host->flags & SDHCI_REQ_USE_DMA)
1223                 mode |= SDHCI_TRNS_DMA;
1224
1225         sdhci_writew(host, mode, SDHCI_TRANSFER_MODE);
1226 }
1227
1228 static bool sdhci_needs_reset(struct sdhci_host *host, struct mmc_request *mrq)
1229 {
1230         return (!(host->flags & SDHCI_DEVICE_DEAD) &&
1231                 ((mrq->cmd && mrq->cmd->error) ||
1232                  (mrq->sbc && mrq->sbc->error) ||
1233                  (mrq->data && mrq->data->stop && mrq->data->stop->error) ||
1234                  (host->quirks & SDHCI_QUIRK_RESET_AFTER_REQUEST)));
1235 }
1236
1237 static void __sdhci_finish_mrq(struct sdhci_host *host, struct mmc_request *mrq)
1238 {
1239         int i;
1240
1241         if (host->cmd && host->cmd->mrq == mrq)
1242                 host->cmd = NULL;
1243
1244         if (host->data_cmd && host->data_cmd->mrq == mrq)
1245                 host->data_cmd = NULL;
1246
1247         if (host->data && host->data->mrq == mrq)
1248                 host->data = NULL;
1249
1250         if (sdhci_needs_reset(host, mrq))
1251                 host->pending_reset = true;
1252
1253         for (i = 0; i < SDHCI_MAX_MRQS; i++) {
1254                 if (host->mrqs_done[i] == mrq) {
1255                         WARN_ON(1);
1256                         return;
1257                 }
1258         }
1259
1260         for (i = 0; i < SDHCI_MAX_MRQS; i++) {
1261                 if (!host->mrqs_done[i]) {
1262                         host->mrqs_done[i] = mrq;
1263                         break;
1264                 }
1265         }
1266
1267         WARN_ON(i >= SDHCI_MAX_MRQS);
1268
1269         sdhci_del_timer(host, mrq);
1270
1271         if (!sdhci_has_requests(host))
1272                 sdhci_led_deactivate(host);
1273 }
1274
1275 static void sdhci_finish_mrq(struct sdhci_host *host, struct mmc_request *mrq)
1276 {
1277         __sdhci_finish_mrq(host, mrq);
1278
1279         queue_work(host->complete_wq, &host->complete_work);
1280 }
1281
1282 static void sdhci_finish_data(struct sdhci_host *host)
1283 {
1284         struct mmc_command *data_cmd = host->data_cmd;
1285         struct mmc_data *data = host->data;
1286
1287         host->data = NULL;
1288         host->data_cmd = NULL;
1289
1290         /*
1291          * The controller needs a reset of internal state machines upon error
1292          * conditions.
1293          */
1294         if (data->error) {
1295                 if (!host->cmd || host->cmd == data_cmd)
1296                         sdhci_do_reset(host, SDHCI_RESET_CMD);
1297                 sdhci_do_reset(host, SDHCI_RESET_DATA);
1298         }
1299
1300         if ((host->flags & (SDHCI_REQ_USE_DMA | SDHCI_USE_ADMA)) ==
1301             (SDHCI_REQ_USE_DMA | SDHCI_USE_ADMA))
1302                 sdhci_adma_table_post(host, data);
1303
1304         /*
1305          * The specification states that the block count register must
1306          * be updated, but it does not specify at what point in the
1307          * data flow. That makes the register entirely useless to read
1308          * back so we have to assume that nothing made it to the card
1309          * in the event of an error.
1310          */
1311         if (data->error)
1312                 data->bytes_xfered = 0;
1313         else
1314                 data->bytes_xfered = data->blksz * data->blocks;
1315
1316         /*
1317          * Need to send CMD12 if -
1318          * a) open-ended multiblock transfer (no CMD23)
1319          * b) error in multiblock transfer
1320          */
1321         if (data->stop &&
1322             (data->error ||
1323              !data->mrq->sbc)) {
1324                 /*
1325                  * 'cap_cmd_during_tfr' request must not use the command line
1326                  * after mmc_command_done() has been called. It is upper layer's
1327                  * responsibility to send the stop command if required.
1328                  */
1329                 if (data->mrq->cap_cmd_during_tfr) {
1330                         __sdhci_finish_mrq(host, data->mrq);
1331                 } else {
1332                         /* Avoid triggering warning in sdhci_send_command() */
1333                         host->cmd = NULL;
1334                         sdhci_send_command(host, data->stop);
1335                 }
1336         } else {
1337                 __sdhci_finish_mrq(host, data->mrq);
1338         }
1339 }
1340
1341 void sdhci_send_command(struct sdhci_host *host, struct mmc_command *cmd)
1342 {
1343         int flags;
1344         u32 mask;
1345         unsigned long timeout;
1346
1347         WARN_ON(host->cmd);
1348
1349         /* Initially, a command has no error */
1350         cmd->error = 0;
1351
1352         if ((host->quirks2 & SDHCI_QUIRK2_STOP_WITH_TC) &&
1353             cmd->opcode == MMC_STOP_TRANSMISSION)
1354                 cmd->flags |= MMC_RSP_BUSY;
1355
1356         /* Wait max 10 ms */
1357         timeout = 10;
1358
1359         mask = SDHCI_CMD_INHIBIT;
1360         if (sdhci_data_line_cmd(cmd))
1361                 mask |= SDHCI_DATA_INHIBIT;
1362
1363         /* We shouldn't wait for data inihibit for stop commands, even
1364            though they might use busy signaling */
1365         if (cmd->mrq->data && (cmd == cmd->mrq->data->stop))
1366                 mask &= ~SDHCI_DATA_INHIBIT;
1367
1368         while (sdhci_readl(host, SDHCI_PRESENT_STATE) & mask) {
1369                 if (timeout == 0) {
1370                         pr_err("%s: Controller never released inhibit bit(s).\n",
1371                                mmc_hostname(host->mmc));
1372                         sdhci_dumpregs(host);
1373                         cmd->error = -EIO;
1374                         sdhci_finish_mrq(host, cmd->mrq);
1375                         return;
1376                 }
1377                 timeout--;
1378                 mdelay(1);
1379         }
1380
1381         host->cmd = cmd;
1382         if (sdhci_data_line_cmd(cmd)) {
1383                 WARN_ON(host->data_cmd);
1384                 host->data_cmd = cmd;
1385         }
1386
1387         sdhci_prepare_data(host, cmd);
1388
1389         sdhci_writel(host, cmd->arg, SDHCI_ARGUMENT);
1390
1391         sdhci_set_transfer_mode(host, cmd);
1392
1393         if ((cmd->flags & MMC_RSP_136) && (cmd->flags & MMC_RSP_BUSY)) {
1394                 pr_err("%s: Unsupported response type!\n",
1395                         mmc_hostname(host->mmc));
1396                 cmd->error = -EINVAL;
1397                 sdhci_finish_mrq(host, cmd->mrq);
1398                 return;
1399         }
1400
1401         if (!(cmd->flags & MMC_RSP_PRESENT))
1402                 flags = SDHCI_CMD_RESP_NONE;
1403         else if (cmd->flags & MMC_RSP_136)
1404                 flags = SDHCI_CMD_RESP_LONG;
1405         else if (cmd->flags & MMC_RSP_BUSY)
1406                 flags = SDHCI_CMD_RESP_SHORT_BUSY;
1407         else
1408                 flags = SDHCI_CMD_RESP_SHORT;
1409
1410         if (cmd->flags & MMC_RSP_CRC)
1411                 flags |= SDHCI_CMD_CRC;
1412         if (cmd->flags & MMC_RSP_OPCODE)
1413                 flags |= SDHCI_CMD_INDEX;
1414
1415         /* CMD19 is special in that the Data Present Select should be set */
1416         if (cmd->data || cmd->opcode == MMC_SEND_TUNING_BLOCK ||
1417             cmd->opcode == MMC_SEND_TUNING_BLOCK_HS200)
1418                 flags |= SDHCI_CMD_DATA;
1419
1420         timeout = jiffies;
1421         if (host->data_timeout)
1422                 timeout += nsecs_to_jiffies(host->data_timeout);
1423         else if (!cmd->data && cmd->busy_timeout > 9000)
1424                 timeout += DIV_ROUND_UP(cmd->busy_timeout, 1000) * HZ + HZ;
1425         else
1426                 timeout += 10 * HZ;
1427         sdhci_mod_timer(host, cmd->mrq, timeout);
1428
1429         sdhci_writew(host, SDHCI_MAKE_CMD(cmd->opcode, flags), SDHCI_COMMAND);
1430 }
1431 EXPORT_SYMBOL_GPL(sdhci_send_command);
1432
1433 static void sdhci_read_rsp_136(struct sdhci_host *host, struct mmc_command *cmd)
1434 {
1435         int i, reg;
1436
1437         for (i = 0; i < 4; i++) {
1438                 reg = SDHCI_RESPONSE + (3 - i) * 4;
1439                 cmd->resp[i] = sdhci_readl(host, reg);
1440         }
1441
1442         if (host->quirks2 & SDHCI_QUIRK2_RSP_136_HAS_CRC)
1443                 return;
1444
1445         /* CRC is stripped so we need to do some shifting */
1446         for (i = 0; i < 4; i++) {
1447                 cmd->resp[i] <<= 8;
1448                 if (i != 3)
1449                         cmd->resp[i] |= cmd->resp[i + 1] >> 24;
1450         }
1451 }
1452
1453 static void sdhci_finish_command(struct sdhci_host *host)
1454 {
1455         struct mmc_command *cmd = host->cmd;
1456
1457         host->cmd = NULL;
1458
1459         if (cmd->flags & MMC_RSP_PRESENT) {
1460                 if (cmd->flags & MMC_RSP_136) {
1461                         sdhci_read_rsp_136(host, cmd);
1462                 } else {
1463                         cmd->resp[0] = sdhci_readl(host, SDHCI_RESPONSE);
1464                 }
1465         }
1466
1467         if (cmd->mrq->cap_cmd_during_tfr && cmd == cmd->mrq->cmd)
1468                 mmc_command_done(host->mmc, cmd->mrq);
1469
1470         /*
1471          * The host can send and interrupt when the busy state has
1472          * ended, allowing us to wait without wasting CPU cycles.
1473          * The busy signal uses DAT0 so this is similar to waiting
1474          * for data to complete.
1475          *
1476          * Note: The 1.0 specification is a bit ambiguous about this
1477          *       feature so there might be some problems with older
1478          *       controllers.
1479          */
1480         if (cmd->flags & MMC_RSP_BUSY) {
1481                 if (cmd->data) {
1482                         DBG("Cannot wait for busy signal when also doing a data transfer");
1483                 } else if (!(host->quirks & SDHCI_QUIRK_NO_BUSY_IRQ) &&
1484                            cmd == host->data_cmd) {
1485                         /* Command complete before busy is ended */
1486                         return;
1487                 }
1488         }
1489
1490         /* Finished CMD23, now send actual command. */
1491         if (cmd == cmd->mrq->sbc) {
1492                 sdhci_send_command(host, cmd->mrq->cmd);
1493         } else {
1494
1495                 /* Processed actual command. */
1496                 if (host->data && host->data_early)
1497                         sdhci_finish_data(host);
1498
1499                 if (!cmd->data)
1500                         __sdhci_finish_mrq(host, cmd->mrq);
1501         }
1502 }
1503
1504 static u16 sdhci_get_preset_value(struct sdhci_host *host)
1505 {
1506         u16 preset = 0;
1507
1508         switch (host->timing) {
1509         case MMC_TIMING_UHS_SDR12:
1510                 preset = sdhci_readw(host, SDHCI_PRESET_FOR_SDR12);
1511                 break;
1512         case MMC_TIMING_UHS_SDR25:
1513                 preset = sdhci_readw(host, SDHCI_PRESET_FOR_SDR25);
1514                 break;
1515         case MMC_TIMING_UHS_SDR50:
1516                 preset = sdhci_readw(host, SDHCI_PRESET_FOR_SDR50);
1517                 break;
1518         case MMC_TIMING_UHS_SDR104:
1519         case MMC_TIMING_MMC_HS200:
1520                 preset = sdhci_readw(host, SDHCI_PRESET_FOR_SDR104);
1521                 break;
1522         case MMC_TIMING_UHS_DDR50:
1523         case MMC_TIMING_MMC_DDR52:
1524                 preset = sdhci_readw(host, SDHCI_PRESET_FOR_DDR50);
1525                 break;
1526         case MMC_TIMING_MMC_HS400:
1527                 preset = sdhci_readw(host, SDHCI_PRESET_FOR_HS400);
1528                 break;
1529         default:
1530                 pr_warn("%s: Invalid UHS-I mode selected\n",
1531                         mmc_hostname(host->mmc));
1532                 preset = sdhci_readw(host, SDHCI_PRESET_FOR_SDR12);
1533                 break;
1534         }
1535         return preset;
1536 }
1537
1538 u16 sdhci_calc_clk(struct sdhci_host *host, unsigned int clock,
1539                    unsigned int *actual_clock)
1540 {
1541         int div = 0; /* Initialized for compiler warning */
1542         int real_div = div, clk_mul = 1;
1543         u16 clk = 0;
1544         bool switch_base_clk = false;
1545
1546         if (host->version >= SDHCI_SPEC_300) {
1547                 if (host->preset_enabled) {
1548                         u16 pre_val;
1549
1550                         clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
1551                         pre_val = sdhci_get_preset_value(host);
1552                         div = (pre_val & SDHCI_PRESET_SDCLK_FREQ_MASK)
1553                                 >> SDHCI_PRESET_SDCLK_FREQ_SHIFT;
1554                         if (host->clk_mul &&
1555                                 (pre_val & SDHCI_PRESET_CLKGEN_SEL_MASK)) {
1556                                 clk = SDHCI_PROG_CLOCK_MODE;
1557                                 real_div = div + 1;
1558                                 clk_mul = host->clk_mul;
1559                         } else {
1560                                 real_div = max_t(int, 1, div << 1);
1561                         }
1562                         goto clock_set;
1563                 }
1564
1565                 /*
1566                  * Check if the Host Controller supports Programmable Clock
1567                  * Mode.
1568                  */
1569                 if (host->clk_mul) {
1570                         for (div = 1; div <= 1024; div++) {
1571                                 if ((host->max_clk * host->clk_mul / div)
1572                                         <= clock)
1573                                         break;
1574                         }
1575                         if ((host->max_clk * host->clk_mul / div) <= clock) {
1576                                 /*
1577                                  * Set Programmable Clock Mode in the Clock
1578                                  * Control register.
1579                                  */
1580                                 clk = SDHCI_PROG_CLOCK_MODE;
1581                                 real_div = div;
1582                                 clk_mul = host->clk_mul;
1583                                 div--;
1584                         } else {
1585                                 /*
1586                                  * Divisor can be too small to reach clock
1587                                  * speed requirement. Then use the base clock.
1588                                  */
1589                                 switch_base_clk = true;
1590                         }
1591                 }
1592
1593                 if (!host->clk_mul || switch_base_clk) {
1594                         /* Version 3.00 divisors must be a multiple of 2. */
1595                         if (host->max_clk <= clock)
1596                                 div = 1;
1597                         else {
1598                                 for (div = 2; div < SDHCI_MAX_DIV_SPEC_300;
1599                                      div += 2) {
1600                                         if ((host->max_clk / div) <= clock)
1601                                                 break;
1602                                 }
1603                         }
1604                         real_div = div;
1605                         div >>= 1;
1606                         if ((host->quirks2 & SDHCI_QUIRK2_CLOCK_DIV_ZERO_BROKEN)
1607                                 && !div && host->max_clk <= 25000000)
1608                                 div = 1;
1609                 }
1610         } else {
1611                 /* Version 2.00 divisors must be a power of 2. */
1612                 for (div = 1; div < SDHCI_MAX_DIV_SPEC_200; div *= 2) {
1613                         if ((host->max_clk / div) <= clock)
1614                                 break;
1615                 }
1616                 real_div = div;
1617                 div >>= 1;
1618         }
1619
1620 clock_set:
1621         if (real_div)
1622                 *actual_clock = (host->max_clk * clk_mul) / real_div;
1623         clk |= (div & SDHCI_DIV_MASK) << SDHCI_DIVIDER_SHIFT;
1624         clk |= ((div & SDHCI_DIV_HI_MASK) >> SDHCI_DIV_MASK_LEN)
1625                 << SDHCI_DIVIDER_HI_SHIFT;
1626
1627         return clk;
1628 }
1629 EXPORT_SYMBOL_GPL(sdhci_calc_clk);
1630
1631 void sdhci_enable_clk(struct sdhci_host *host, u16 clk)
1632 {
1633         ktime_t timeout;
1634
1635         clk |= SDHCI_CLOCK_INT_EN;
1636         sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
1637
1638         /* Wait max 150 ms */
1639         timeout = ktime_add_ms(ktime_get(), 150);
1640         while (1) {
1641                 bool timedout = ktime_after(ktime_get(), timeout);
1642
1643                 clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
1644                 if (clk & SDHCI_CLOCK_INT_STABLE)
1645                         break;
1646                 if (timedout) {
1647                         pr_err("%s: Internal clock never stabilised.\n",
1648                                mmc_hostname(host->mmc));
1649                         sdhci_dumpregs(host);
1650                         return;
1651                 }
1652                 udelay(10);
1653         }
1654
1655         if (host->version >= SDHCI_SPEC_410 && host->v4_mode) {
1656                 clk |= SDHCI_CLOCK_PLL_EN;
1657                 clk &= ~SDHCI_CLOCK_INT_STABLE;
1658                 sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
1659
1660                 /* Wait max 150 ms */
1661                 timeout = ktime_add_ms(ktime_get(), 150);
1662                 while (1) {
1663                         bool timedout = ktime_after(ktime_get(), timeout);
1664
1665                         clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
1666                         if (clk & SDHCI_CLOCK_INT_STABLE)
1667                                 break;
1668                         if (timedout) {
1669                                 pr_err("%s: PLL clock never stabilised.\n",
1670                                        mmc_hostname(host->mmc));
1671                                 sdhci_dumpregs(host);
1672                                 return;
1673                         }
1674                         udelay(10);
1675                 }
1676         }
1677
1678         clk |= SDHCI_CLOCK_CARD_EN;
1679         sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
1680 }
1681 EXPORT_SYMBOL_GPL(sdhci_enable_clk);
1682
1683 void sdhci_set_clock(struct sdhci_host *host, unsigned int clock)
1684 {
1685         u16 clk;
1686
1687         host->mmc->actual_clock = 0;
1688
1689         sdhci_writew(host, 0, SDHCI_CLOCK_CONTROL);
1690
1691         if (clock == 0)
1692                 return;
1693
1694         clk = sdhci_calc_clk(host, clock, &host->mmc->actual_clock);
1695         sdhci_enable_clk(host, clk);
1696 }
1697 EXPORT_SYMBOL_GPL(sdhci_set_clock);
1698
1699 static void sdhci_set_power_reg(struct sdhci_host *host, unsigned char mode,
1700                                 unsigned short vdd)
1701 {
1702         struct mmc_host *mmc = host->mmc;
1703
1704         mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, vdd);
1705
1706         if (mode != MMC_POWER_OFF)
1707                 sdhci_writeb(host, SDHCI_POWER_ON, SDHCI_POWER_CONTROL);
1708         else
1709                 sdhci_writeb(host, 0, SDHCI_POWER_CONTROL);
1710 }
1711
1712 void sdhci_set_power_noreg(struct sdhci_host *host, unsigned char mode,
1713                            unsigned short vdd)
1714 {
1715         u8 pwr = 0;
1716
1717         if (mode != MMC_POWER_OFF) {
1718                 switch (1 << vdd) {
1719                 case MMC_VDD_165_195:
1720                 /*
1721                  * Without a regulator, SDHCI does not support 2.0v
1722                  * so we only get here if the driver deliberately
1723                  * added the 2.0v range to ocr_avail. Map it to 1.8v
1724                  * for the purpose of turning on the power.
1725                  */
1726                 case MMC_VDD_20_21:
1727                         pwr = SDHCI_POWER_180;
1728                         break;
1729                 case MMC_VDD_29_30:
1730                 case MMC_VDD_30_31:
1731                         pwr = SDHCI_POWER_300;
1732                         break;
1733                 case MMC_VDD_32_33:
1734                 case MMC_VDD_33_34:
1735                         pwr = SDHCI_POWER_330;
1736                         break;
1737                 default:
1738                         WARN(1, "%s: Invalid vdd %#x\n",
1739                              mmc_hostname(host->mmc), vdd);
1740                         break;
1741                 }
1742         }
1743
1744         if (host->pwr == pwr)
1745                 return;
1746
1747         host->pwr = pwr;
1748
1749         if (pwr == 0) {
1750                 sdhci_writeb(host, 0, SDHCI_POWER_CONTROL);
1751                 if (host->quirks2 & SDHCI_QUIRK2_CARD_ON_NEEDS_BUS_ON)
1752                         sdhci_runtime_pm_bus_off(host);
1753         } else {
1754                 /*
1755                  * Spec says that we should clear the power reg before setting
1756                  * a new value. Some controllers don't seem to like this though.
1757                  */
1758                 if (!(host->quirks & SDHCI_QUIRK_SINGLE_POWER_WRITE))
1759                         sdhci_writeb(host, 0, SDHCI_POWER_CONTROL);
1760
1761                 /*
1762                  * At least the Marvell CaFe chip gets confused if we set the
1763                  * voltage and set turn on power at the same time, so set the
1764                  * voltage first.
1765                  */
1766                 if (host->quirks & SDHCI_QUIRK_NO_SIMULT_VDD_AND_POWER)
1767                         sdhci_writeb(host, pwr, SDHCI_POWER_CONTROL);
1768
1769                 pwr |= SDHCI_POWER_ON;
1770
1771                 sdhci_writeb(host, pwr, SDHCI_POWER_CONTROL);
1772
1773                 if (host->quirks2 & SDHCI_QUIRK2_CARD_ON_NEEDS_BUS_ON)
1774                         sdhci_runtime_pm_bus_on(host);
1775
1776                 /*
1777                  * Some controllers need an extra 10ms delay of 10ms before
1778                  * they can apply clock after applying power
1779                  */
1780                 if (host->quirks & SDHCI_QUIRK_DELAY_AFTER_POWER)
1781                         mdelay(10);
1782         }
1783 }
1784 EXPORT_SYMBOL_GPL(sdhci_set_power_noreg);
1785
1786 void sdhci_set_power(struct sdhci_host *host, unsigned char mode,
1787                      unsigned short vdd)
1788 {
1789         if (IS_ERR(host->mmc->supply.vmmc))
1790                 sdhci_set_power_noreg(host, mode, vdd);
1791         else
1792                 sdhci_set_power_reg(host, mode, vdd);
1793 }
1794 EXPORT_SYMBOL_GPL(sdhci_set_power);
1795
1796 /*****************************************************************************\
1797  *                                                                           *
1798  * MMC callbacks                                                             *
1799  *                                                                           *
1800 \*****************************************************************************/
1801
1802 void sdhci_request(struct mmc_host *mmc, struct mmc_request *mrq)
1803 {
1804         struct sdhci_host *host;
1805         int present;
1806         unsigned long flags;
1807
1808         host = mmc_priv(mmc);
1809
1810         /* Firstly check card presence */
1811         present = mmc->ops->get_cd(mmc);
1812
1813         spin_lock_irqsave(&host->lock, flags);
1814
1815         sdhci_led_activate(host);
1816
1817         /*
1818          * Ensure we don't send the STOP for non-SET_BLOCK_COUNTED
1819          * requests if Auto-CMD12 is enabled.
1820          */
1821         if (sdhci_auto_cmd12(host, mrq)) {
1822                 if (mrq->stop) {
1823                         mrq->data->stop = NULL;
1824                         mrq->stop = NULL;
1825                 }
1826         }
1827
1828         if (!present || host->flags & SDHCI_DEVICE_DEAD) {
1829                 mrq->cmd->error = -ENOMEDIUM;
1830                 sdhci_finish_mrq(host, mrq);
1831         } else {
1832                 if (mrq->sbc && !(host->flags & SDHCI_AUTO_CMD23))
1833                         sdhci_send_command(host, mrq->sbc);
1834                 else
1835                         sdhci_send_command(host, mrq->cmd);
1836         }
1837
1838         spin_unlock_irqrestore(&host->lock, flags);
1839 }
1840 EXPORT_SYMBOL_GPL(sdhci_request);
1841
1842 void sdhci_set_bus_width(struct sdhci_host *host, int width)
1843 {
1844         u8 ctrl;
1845
1846         ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
1847         if (width == MMC_BUS_WIDTH_8) {
1848                 ctrl &= ~SDHCI_CTRL_4BITBUS;
1849                 ctrl |= SDHCI_CTRL_8BITBUS;
1850         } else {
1851                 if (host->mmc->caps & MMC_CAP_8_BIT_DATA)
1852                         ctrl &= ~SDHCI_CTRL_8BITBUS;
1853                 if (width == MMC_BUS_WIDTH_4)
1854                         ctrl |= SDHCI_CTRL_4BITBUS;
1855                 else
1856                         ctrl &= ~SDHCI_CTRL_4BITBUS;
1857         }
1858         sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
1859 }
1860 EXPORT_SYMBOL_GPL(sdhci_set_bus_width);
1861
1862 void sdhci_set_uhs_signaling(struct sdhci_host *host, unsigned timing)
1863 {
1864         u16 ctrl_2;
1865
1866         ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
1867         /* Select Bus Speed Mode for host */
1868         ctrl_2 &= ~SDHCI_CTRL_UHS_MASK;
1869         if ((timing == MMC_TIMING_MMC_HS200) ||
1870             (timing == MMC_TIMING_UHS_SDR104))
1871                 ctrl_2 |= SDHCI_CTRL_UHS_SDR104;
1872         else if (timing == MMC_TIMING_UHS_SDR12)
1873                 ctrl_2 |= SDHCI_CTRL_UHS_SDR12;
1874         else if (timing == MMC_TIMING_SD_HS ||
1875                  timing == MMC_TIMING_MMC_HS ||
1876                  timing == MMC_TIMING_UHS_SDR25)
1877                 ctrl_2 |= SDHCI_CTRL_UHS_SDR25;
1878         else if (timing == MMC_TIMING_UHS_SDR50)
1879                 ctrl_2 |= SDHCI_CTRL_UHS_SDR50;
1880         else if ((timing == MMC_TIMING_UHS_DDR50) ||
1881                  (timing == MMC_TIMING_MMC_DDR52))
1882                 ctrl_2 |= SDHCI_CTRL_UHS_DDR50;
1883         else if (timing == MMC_TIMING_MMC_HS400)
1884                 ctrl_2 |= SDHCI_CTRL_HS400; /* Non-standard */
1885         sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
1886 }
1887 EXPORT_SYMBOL_GPL(sdhci_set_uhs_signaling);
1888
1889 void sdhci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
1890 {
1891         struct sdhci_host *host = mmc_priv(mmc);
1892         u8 ctrl;
1893
1894         if (ios->power_mode == MMC_POWER_UNDEFINED)
1895                 return;
1896
1897         if (host->flags & SDHCI_DEVICE_DEAD) {
1898                 if (!IS_ERR(mmc->supply.vmmc) &&
1899                     ios->power_mode == MMC_POWER_OFF)
1900                         mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, 0);
1901                 return;
1902         }
1903
1904         /*
1905          * Reset the chip on each power off.
1906          * Should clear out any weird states.
1907          */
1908         if (ios->power_mode == MMC_POWER_OFF) {
1909                 sdhci_writel(host, 0, SDHCI_SIGNAL_ENABLE);
1910                 sdhci_reinit(host);
1911         }
1912
1913         if (host->version >= SDHCI_SPEC_300 &&
1914                 (ios->power_mode == MMC_POWER_UP) &&
1915                 !(host->quirks2 & SDHCI_QUIRK2_PRESET_VALUE_BROKEN))
1916                 sdhci_enable_preset_value(host, false);
1917
1918         if (!ios->clock || ios->clock != host->clock) {
1919                 host->ops->set_clock(host, ios->clock);
1920                 host->clock = ios->clock;
1921
1922                 if (host->quirks & SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK &&
1923                     host->clock) {
1924                         host->timeout_clk = host->mmc->actual_clock ?
1925                                                 host->mmc->actual_clock / 1000 :
1926                                                 host->clock / 1000;
1927                         host->mmc->max_busy_timeout =
1928                                 host->ops->get_max_timeout_count ?
1929                                 host->ops->get_max_timeout_count(host) :
1930                                 1 << 27;
1931                         host->mmc->max_busy_timeout /= host->timeout_clk;
1932                 }
1933         }
1934
1935         if (host->ops->set_power)
1936                 host->ops->set_power(host, ios->power_mode, ios->vdd);
1937         else
1938                 sdhci_set_power(host, ios->power_mode, ios->vdd);
1939
1940         if (host->ops->platform_send_init_74_clocks)
1941                 host->ops->platform_send_init_74_clocks(host, ios->power_mode);
1942
1943         host->ops->set_bus_width(host, ios->bus_width);
1944
1945         ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
1946
1947         if (!(host->quirks & SDHCI_QUIRK_NO_HISPD_BIT)) {
1948                 if (ios->timing == MMC_TIMING_SD_HS ||
1949                      ios->timing == MMC_TIMING_MMC_HS ||
1950                      ios->timing == MMC_TIMING_MMC_HS400 ||
1951                      ios->timing == MMC_TIMING_MMC_HS200 ||
1952                      ios->timing == MMC_TIMING_MMC_DDR52 ||
1953                      ios->timing == MMC_TIMING_UHS_SDR50 ||
1954                      ios->timing == MMC_TIMING_UHS_SDR104 ||
1955                      ios->timing == MMC_TIMING_UHS_DDR50 ||
1956                      ios->timing == MMC_TIMING_UHS_SDR25)
1957                         ctrl |= SDHCI_CTRL_HISPD;
1958                 else
1959                         ctrl &= ~SDHCI_CTRL_HISPD;
1960         }
1961
1962         if (host->version >= SDHCI_SPEC_300) {
1963                 u16 clk, ctrl_2;
1964
1965                 if (!host->preset_enabled) {
1966                         sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
1967                         /*
1968                          * We only need to set Driver Strength if the
1969                          * preset value enable is not set.
1970                          */
1971                         ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
1972                         ctrl_2 &= ~SDHCI_CTRL_DRV_TYPE_MASK;
1973                         if (ios->drv_type == MMC_SET_DRIVER_TYPE_A)
1974                                 ctrl_2 |= SDHCI_CTRL_DRV_TYPE_A;
1975                         else if (ios->drv_type == MMC_SET_DRIVER_TYPE_B)
1976                                 ctrl_2 |= SDHCI_CTRL_DRV_TYPE_B;
1977                         else if (ios->drv_type == MMC_SET_DRIVER_TYPE_C)
1978                                 ctrl_2 |= SDHCI_CTRL_DRV_TYPE_C;
1979                         else if (ios->drv_type == MMC_SET_DRIVER_TYPE_D)
1980                                 ctrl_2 |= SDHCI_CTRL_DRV_TYPE_D;
1981                         else {
1982                                 pr_warn("%s: invalid driver type, default to driver type B\n",
1983                                         mmc_hostname(mmc));
1984                                 ctrl_2 |= SDHCI_CTRL_DRV_TYPE_B;
1985                         }
1986
1987                         sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
1988                 } else {
1989                         /*
1990                          * According to SDHC Spec v3.00, if the Preset Value
1991                          * Enable in the Host Control 2 register is set, we
1992                          * need to reset SD Clock Enable before changing High
1993                          * Speed Enable to avoid generating clock gliches.
1994                          */
1995
1996                         /* Reset SD Clock Enable */
1997                         clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
1998                         clk &= ~SDHCI_CLOCK_CARD_EN;
1999                         sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
2000
2001                         sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
2002
2003                         /* Re-enable SD Clock */
2004                         host->ops->set_clock(host, host->clock);
2005                 }
2006
2007                 /* Reset SD Clock Enable */
2008                 clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
2009                 clk &= ~SDHCI_CLOCK_CARD_EN;
2010                 sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
2011
2012                 host->ops->set_uhs_signaling(host, ios->timing);
2013                 host->timing = ios->timing;
2014
2015                 if (!(host->quirks2 & SDHCI_QUIRK2_PRESET_VALUE_BROKEN) &&
2016                                 ((ios->timing == MMC_TIMING_UHS_SDR12) ||
2017                                  (ios->timing == MMC_TIMING_UHS_SDR25) ||
2018                                  (ios->timing == MMC_TIMING_UHS_SDR50) ||
2019                                  (ios->timing == MMC_TIMING_UHS_SDR104) ||
2020                                  (ios->timing == MMC_TIMING_UHS_DDR50) ||
2021                                  (ios->timing == MMC_TIMING_MMC_DDR52))) {
2022                         u16 preset;
2023
2024                         sdhci_enable_preset_value(host, true);
2025                         preset = sdhci_get_preset_value(host);
2026                         ios->drv_type = (preset & SDHCI_PRESET_DRV_MASK)
2027                                 >> SDHCI_PRESET_DRV_SHIFT;
2028                 }
2029
2030                 /* Re-enable SD Clock */
2031                 host->ops->set_clock(host, host->clock);
2032         } else
2033                 sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
2034
2035         /*
2036          * Some (ENE) controllers go apeshit on some ios operation,
2037          * signalling timeout and CRC errors even on CMD0. Resetting
2038          * it on each ios seems to solve the problem.
2039          */
2040         if (host->quirks & SDHCI_QUIRK_RESET_CMD_DATA_ON_IOS)
2041                 sdhci_do_reset(host, SDHCI_RESET_CMD | SDHCI_RESET_DATA);
2042 }
2043 EXPORT_SYMBOL_GPL(sdhci_set_ios);
2044
2045 static int sdhci_get_cd(struct mmc_host *mmc)
2046 {
2047         struct sdhci_host *host = mmc_priv(mmc);
2048         int gpio_cd = mmc_gpio_get_cd(mmc);
2049
2050         if (host->flags & SDHCI_DEVICE_DEAD)
2051                 return 0;
2052
2053         /* If nonremovable, assume that the card is always present. */
2054         if (!mmc_card_is_removable(host->mmc))
2055                 return 1;
2056
2057         /*
2058          * Try slot gpio detect, if defined it take precedence
2059          * over build in controller functionality
2060          */
2061         if (gpio_cd >= 0)
2062                 return !!gpio_cd;
2063
2064         /* If polling, assume that the card is always present. */
2065         if (host->quirks & SDHCI_QUIRK_BROKEN_CARD_DETECTION)
2066                 return 1;
2067
2068         /* Host native card detect */
2069         return !!(sdhci_readl(host, SDHCI_PRESENT_STATE) & SDHCI_CARD_PRESENT);
2070 }
2071
2072 static int sdhci_check_ro(struct sdhci_host *host)
2073 {
2074         unsigned long flags;
2075         int is_readonly;
2076
2077         spin_lock_irqsave(&host->lock, flags);
2078
2079         if (host->flags & SDHCI_DEVICE_DEAD)
2080                 is_readonly = 0;
2081         else if (host->ops->get_ro)
2082                 is_readonly = host->ops->get_ro(host);
2083         else if (mmc_can_gpio_ro(host->mmc))
2084                 is_readonly = mmc_gpio_get_ro(host->mmc);
2085         else
2086                 is_readonly = !(sdhci_readl(host, SDHCI_PRESENT_STATE)
2087                                 & SDHCI_WRITE_PROTECT);
2088
2089         spin_unlock_irqrestore(&host->lock, flags);
2090
2091         /* This quirk needs to be replaced by a callback-function later */
2092         return host->quirks & SDHCI_QUIRK_INVERTED_WRITE_PROTECT ?
2093                 !is_readonly : is_readonly;
2094 }
2095
2096 #define SAMPLE_COUNT    5
2097
2098 static int sdhci_get_ro(struct mmc_host *mmc)
2099 {
2100         struct sdhci_host *host = mmc_priv(mmc);
2101         int i, ro_count;
2102
2103         if (!(host->quirks & SDHCI_QUIRK_UNSTABLE_RO_DETECT))
2104                 return sdhci_check_ro(host);
2105
2106         ro_count = 0;
2107         for (i = 0; i < SAMPLE_COUNT; i++) {
2108                 if (sdhci_check_ro(host)) {
2109                         if (++ro_count > SAMPLE_COUNT / 2)
2110                                 return 1;
2111                 }
2112                 msleep(30);
2113         }
2114         return 0;
2115 }
2116
2117 static void sdhci_hw_reset(struct mmc_host *mmc)
2118 {
2119         struct sdhci_host *host = mmc_priv(mmc);
2120
2121         if (host->ops && host->ops->hw_reset)
2122                 host->ops->hw_reset(host);
2123 }
2124
2125 static void sdhci_enable_sdio_irq_nolock(struct sdhci_host *host, int enable)
2126 {
2127         if (!(host->flags & SDHCI_DEVICE_DEAD)) {
2128                 if (enable)
2129                         host->ier |= SDHCI_INT_CARD_INT;
2130                 else
2131                         host->ier &= ~SDHCI_INT_CARD_INT;
2132
2133                 sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
2134                 sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
2135         }
2136 }
2137
2138 void sdhci_enable_sdio_irq(struct mmc_host *mmc, int enable)
2139 {
2140         struct sdhci_host *host = mmc_priv(mmc);
2141         unsigned long flags;
2142
2143         if (enable)
2144                 pm_runtime_get_noresume(host->mmc->parent);
2145
2146         spin_lock_irqsave(&host->lock, flags);
2147         sdhci_enable_sdio_irq_nolock(host, enable);
2148         spin_unlock_irqrestore(&host->lock, flags);
2149
2150         if (!enable)
2151                 pm_runtime_put_noidle(host->mmc->parent);
2152 }
2153 EXPORT_SYMBOL_GPL(sdhci_enable_sdio_irq);
2154
2155 static void sdhci_ack_sdio_irq(struct mmc_host *mmc)
2156 {
2157         struct sdhci_host *host = mmc_priv(mmc);
2158         unsigned long flags;
2159
2160         spin_lock_irqsave(&host->lock, flags);
2161         sdhci_enable_sdio_irq_nolock(host, true);
2162         spin_unlock_irqrestore(&host->lock, flags);
2163 }
2164
2165 int sdhci_start_signal_voltage_switch(struct mmc_host *mmc,
2166                                       struct mmc_ios *ios)
2167 {
2168         struct sdhci_host *host = mmc_priv(mmc);
2169         u16 ctrl;
2170         int ret;
2171
2172         /*
2173          * Signal Voltage Switching is only applicable for Host Controllers
2174          * v3.00 and above.
2175          */
2176         if (host->version < SDHCI_SPEC_300)
2177                 return 0;
2178
2179         ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
2180
2181         switch (ios->signal_voltage) {
2182         case MMC_SIGNAL_VOLTAGE_330:
2183                 if (!(host->flags & SDHCI_SIGNALING_330))
2184                         return -EINVAL;
2185                 /* Set 1.8V Signal Enable in the Host Control2 register to 0 */
2186                 ctrl &= ~SDHCI_CTRL_VDD_180;
2187                 sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
2188
2189                 if (!IS_ERR(mmc->supply.vqmmc)) {
2190                         ret = mmc_regulator_set_vqmmc(mmc, ios);
2191                         if (ret) {
2192                                 pr_warn("%s: Switching to 3.3V signalling voltage failed\n",
2193                                         mmc_hostname(mmc));
2194                                 return -EIO;
2195                         }
2196                 }
2197                 /* Wait for 5ms */
2198                 usleep_range(5000, 5500);
2199
2200                 /* 3.3V regulator output should be stable within 5 ms */
2201                 ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
2202                 if (!(ctrl & SDHCI_CTRL_VDD_180))
2203                         return 0;
2204
2205                 pr_warn("%s: 3.3V regulator output did not became stable\n",
2206                         mmc_hostname(mmc));
2207
2208                 return -EAGAIN;
2209         case MMC_SIGNAL_VOLTAGE_180:
2210                 if (!(host->flags & SDHCI_SIGNALING_180))
2211                         return -EINVAL;
2212                 if (!IS_ERR(mmc->supply.vqmmc)) {
2213                         ret = mmc_regulator_set_vqmmc(mmc, ios);
2214                         if (ret) {
2215                                 pr_warn("%s: Switching to 1.8V signalling voltage failed\n",
2216                                         mmc_hostname(mmc));
2217                                 return -EIO;
2218                         }
2219                 }
2220
2221                 /*
2222                  * Enable 1.8V Signal Enable in the Host Control2
2223                  * register
2224                  */
2225                 ctrl |= SDHCI_CTRL_VDD_180;
2226                 sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
2227
2228                 /* Some controller need to do more when switching */
2229                 if (host->ops->voltage_switch)
2230                         host->ops->voltage_switch(host);
2231
2232                 /* 1.8V regulator output should be stable within 5 ms */
2233                 ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
2234                 if (ctrl & SDHCI_CTRL_VDD_180)
2235                         return 0;
2236
2237                 pr_warn("%s: 1.8V regulator output did not became stable\n",
2238                         mmc_hostname(mmc));
2239
2240                 return -EAGAIN;
2241         case MMC_SIGNAL_VOLTAGE_120:
2242                 if (!(host->flags & SDHCI_SIGNALING_120))
2243                         return -EINVAL;
2244                 if (!IS_ERR(mmc->supply.vqmmc)) {
2245                         ret = mmc_regulator_set_vqmmc(mmc, ios);
2246                         if (ret) {
2247                                 pr_warn("%s: Switching to 1.2V signalling voltage failed\n",
2248                                         mmc_hostname(mmc));
2249                                 return -EIO;
2250                         }
2251                 }
2252                 return 0;
2253         default:
2254                 /* No signal voltage switch required */
2255                 return 0;
2256         }
2257 }
2258 EXPORT_SYMBOL_GPL(sdhci_start_signal_voltage_switch);
2259
2260 static int sdhci_card_busy(struct mmc_host *mmc)
2261 {
2262         struct sdhci_host *host = mmc_priv(mmc);
2263         u32 present_state;
2264
2265         /* Check whether DAT[0] is 0 */
2266         present_state = sdhci_readl(host, SDHCI_PRESENT_STATE);
2267
2268         return !(present_state & SDHCI_DATA_0_LVL_MASK);
2269 }
2270
2271 static int sdhci_prepare_hs400_tuning(struct mmc_host *mmc, struct mmc_ios *ios)
2272 {
2273         struct sdhci_host *host = mmc_priv(mmc);
2274         unsigned long flags;
2275
2276         spin_lock_irqsave(&host->lock, flags);
2277         host->flags |= SDHCI_HS400_TUNING;
2278         spin_unlock_irqrestore(&host->lock, flags);
2279
2280         return 0;
2281 }
2282
2283 void sdhci_start_tuning(struct sdhci_host *host)
2284 {
2285         u16 ctrl;
2286
2287         ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
2288         ctrl |= SDHCI_CTRL_EXEC_TUNING;
2289         if (host->quirks2 & SDHCI_QUIRK2_TUNING_WORK_AROUND)
2290                 ctrl |= SDHCI_CTRL_TUNED_CLK;
2291         sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
2292
2293         /*
2294          * As per the Host Controller spec v3.00, tuning command
2295          * generates Buffer Read Ready interrupt, so enable that.
2296          *
2297          * Note: The spec clearly says that when tuning sequence
2298          * is being performed, the controller does not generate
2299          * interrupts other than Buffer Read Ready interrupt. But
2300          * to make sure we don't hit a controller bug, we _only_
2301          * enable Buffer Read Ready interrupt here.
2302          */
2303         sdhci_writel(host, SDHCI_INT_DATA_AVAIL, SDHCI_INT_ENABLE);
2304         sdhci_writel(host, SDHCI_INT_DATA_AVAIL, SDHCI_SIGNAL_ENABLE);
2305 }
2306 EXPORT_SYMBOL_GPL(sdhci_start_tuning);
2307
2308 void sdhci_end_tuning(struct sdhci_host *host)
2309 {
2310         sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
2311         sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
2312 }
2313 EXPORT_SYMBOL_GPL(sdhci_end_tuning);
2314
2315 void sdhci_reset_tuning(struct sdhci_host *host)
2316 {
2317         u16 ctrl;
2318
2319         ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
2320         ctrl &= ~SDHCI_CTRL_TUNED_CLK;
2321         ctrl &= ~SDHCI_CTRL_EXEC_TUNING;
2322         sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
2323 }
2324 EXPORT_SYMBOL_GPL(sdhci_reset_tuning);
2325
2326 void sdhci_abort_tuning(struct sdhci_host *host, u32 opcode)
2327 {
2328         sdhci_reset_tuning(host);
2329
2330         sdhci_do_reset(host, SDHCI_RESET_CMD);
2331         sdhci_do_reset(host, SDHCI_RESET_DATA);
2332
2333         sdhci_end_tuning(host);
2334
2335         mmc_abort_tuning(host->mmc, opcode);
2336 }
2337 EXPORT_SYMBOL_GPL(sdhci_abort_tuning);
2338
2339 /*
2340  * We use sdhci_send_tuning() because mmc_send_tuning() is not a good fit. SDHCI
2341  * tuning command does not have a data payload (or rather the hardware does it
2342  * automatically) so mmc_send_tuning() will return -EIO. Also the tuning command
2343  * interrupt setup is different to other commands and there is no timeout
2344  * interrupt so special handling is needed.
2345  */
2346 void sdhci_send_tuning(struct sdhci_host *host, u32 opcode)
2347 {
2348         struct mmc_host *mmc = host->mmc;
2349         struct mmc_command cmd = {};
2350         struct mmc_request mrq = {};
2351         unsigned long flags;
2352         u32 b = host->sdma_boundary;
2353
2354         spin_lock_irqsave(&host->lock, flags);
2355
2356         cmd.opcode = opcode;
2357         cmd.flags = MMC_RSP_R1 | MMC_CMD_ADTC;
2358         cmd.mrq = &mrq;
2359
2360         mrq.cmd = &cmd;
2361         /*
2362          * In response to CMD19, the card sends 64 bytes of tuning
2363          * block to the Host Controller. So we set the block size
2364          * to 64 here.
2365          */
2366         if (cmd.opcode == MMC_SEND_TUNING_BLOCK_HS200 &&
2367             mmc->ios.bus_width == MMC_BUS_WIDTH_8)
2368                 sdhci_writew(host, SDHCI_MAKE_BLKSZ(b, 128), SDHCI_BLOCK_SIZE);
2369         else
2370                 sdhci_writew(host, SDHCI_MAKE_BLKSZ(b, 64), SDHCI_BLOCK_SIZE);
2371
2372         /*
2373          * The tuning block is sent by the card to the host controller.
2374          * So we set the TRNS_READ bit in the Transfer Mode register.
2375          * This also takes care of setting DMA Enable and Multi Block
2376          * Select in the same register to 0.
2377          */
2378         sdhci_writew(host, SDHCI_TRNS_READ, SDHCI_TRANSFER_MODE);
2379
2380         sdhci_send_command(host, &cmd);
2381
2382         host->cmd = NULL;
2383
2384         sdhci_del_timer(host, &mrq);
2385
2386         host->tuning_done = 0;
2387
2388         spin_unlock_irqrestore(&host->lock, flags);
2389
2390         /* Wait for Buffer Read Ready interrupt */
2391         wait_event_timeout(host->buf_ready_int, (host->tuning_done == 1),
2392                            msecs_to_jiffies(50));
2393
2394 }
2395 EXPORT_SYMBOL_GPL(sdhci_send_tuning);
2396
2397 static int __sdhci_execute_tuning(struct sdhci_host *host, u32 opcode)
2398 {
2399         int i;
2400
2401         /*
2402          * Issue opcode repeatedly till Execute Tuning is set to 0 or the number
2403          * of loops reaches tuning loop count.
2404          */
2405         for (i = 0; i < host->tuning_loop_count; i++) {
2406                 u16 ctrl;
2407
2408                 sdhci_send_tuning(host, opcode);
2409
2410                 if (!host->tuning_done) {
2411                         pr_info("%s: Tuning timeout, falling back to fixed sampling clock\n",
2412                                 mmc_hostname(host->mmc));
2413                         sdhci_abort_tuning(host, opcode);
2414                         return -ETIMEDOUT;
2415                 }
2416
2417                 /* Spec does not require a delay between tuning cycles */
2418                 if (host->tuning_delay > 0)
2419                         mdelay(host->tuning_delay);
2420
2421                 ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
2422                 if (!(ctrl & SDHCI_CTRL_EXEC_TUNING)) {
2423                         if (ctrl & SDHCI_CTRL_TUNED_CLK)
2424                                 return 0; /* Success! */
2425                         break;
2426                 }
2427
2428         }
2429
2430         pr_info("%s: Tuning failed, falling back to fixed sampling clock\n",
2431                 mmc_hostname(host->mmc));
2432         sdhci_reset_tuning(host);
2433         return -EAGAIN;
2434 }
2435
2436 int sdhci_execute_tuning(struct mmc_host *mmc, u32 opcode)
2437 {
2438         struct sdhci_host *host = mmc_priv(mmc);
2439         int err = 0;
2440         unsigned int tuning_count = 0;
2441         bool hs400_tuning;
2442
2443         hs400_tuning = host->flags & SDHCI_HS400_TUNING;
2444
2445         if (host->tuning_mode == SDHCI_TUNING_MODE_1)
2446                 tuning_count = host->tuning_count;
2447
2448         /*
2449          * The Host Controller needs tuning in case of SDR104 and DDR50
2450          * mode, and for SDR50 mode when Use Tuning for SDR50 is set in
2451          * the Capabilities register.
2452          * If the Host Controller supports the HS200 mode then the
2453          * tuning function has to be executed.
2454          */
2455         switch (host->timing) {
2456         /* HS400 tuning is done in HS200 mode */
2457         case MMC_TIMING_MMC_HS400:
2458                 err = -EINVAL;
2459                 goto out;
2460
2461         case MMC_TIMING_MMC_HS200:
2462                 /*
2463                  * Periodic re-tuning for HS400 is not expected to be needed, so
2464                  * disable it here.
2465                  */
2466                 if (hs400_tuning)
2467                         tuning_count = 0;
2468                 break;
2469
2470         case MMC_TIMING_UHS_SDR104:
2471         case MMC_TIMING_UHS_DDR50:
2472                 break;
2473
2474         case MMC_TIMING_UHS_SDR50:
2475                 if (host->flags & SDHCI_SDR50_NEEDS_TUNING)
2476                         break;
2477                 /* FALLTHROUGH */
2478
2479         default:
2480                 goto out;
2481         }
2482
2483         if (host->ops->platform_execute_tuning) {
2484                 err = host->ops->platform_execute_tuning(host, opcode);
2485                 goto out;
2486         }
2487
2488         host->mmc->retune_period = tuning_count;
2489
2490         if (host->tuning_delay < 0)
2491                 host->tuning_delay = opcode == MMC_SEND_TUNING_BLOCK;
2492
2493         sdhci_start_tuning(host);
2494
2495         host->tuning_err = __sdhci_execute_tuning(host, opcode);
2496
2497         sdhci_end_tuning(host);
2498 out:
2499         host->flags &= ~SDHCI_HS400_TUNING;
2500
2501         return err;
2502 }
2503 EXPORT_SYMBOL_GPL(sdhci_execute_tuning);
2504
2505 static void sdhci_enable_preset_value(struct sdhci_host *host, bool enable)
2506 {
2507         /* Host Controller v3.00 defines preset value registers */
2508         if (host->version < SDHCI_SPEC_300)
2509                 return;
2510
2511         /*
2512          * We only enable or disable Preset Value if they are not already
2513          * enabled or disabled respectively. Otherwise, we bail out.
2514          */
2515         if (host->preset_enabled != enable) {
2516                 u16 ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
2517
2518                 if (enable)
2519                         ctrl |= SDHCI_CTRL_PRESET_VAL_ENABLE;
2520                 else
2521                         ctrl &= ~SDHCI_CTRL_PRESET_VAL_ENABLE;
2522
2523                 sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
2524
2525                 if (enable)
2526                         host->flags |= SDHCI_PV_ENABLED;
2527                 else
2528                         host->flags &= ~SDHCI_PV_ENABLED;
2529
2530                 host->preset_enabled = enable;
2531         }
2532 }
2533
2534 static void sdhci_post_req(struct mmc_host *mmc, struct mmc_request *mrq,
2535                                 int err)
2536 {
2537         struct sdhci_host *host = mmc_priv(mmc);
2538         struct mmc_data *data = mrq->data;
2539
2540         if (data->host_cookie != COOKIE_UNMAPPED)
2541                 dma_unmap_sg(mmc_dev(host->mmc), data->sg, data->sg_len,
2542                              mmc_get_dma_dir(data));
2543
2544         data->host_cookie = COOKIE_UNMAPPED;
2545 }
2546
2547 static void sdhci_pre_req(struct mmc_host *mmc, struct mmc_request *mrq)
2548 {
2549         struct sdhci_host *host = mmc_priv(mmc);
2550
2551         mrq->data->host_cookie = COOKIE_UNMAPPED;
2552
2553         /*
2554          * No pre-mapping in the pre hook if we're using the bounce buffer,
2555          * for that we would need two bounce buffers since one buffer is
2556          * in flight when this is getting called.
2557          */
2558         if (host->flags & SDHCI_REQ_USE_DMA && !host->bounce_buffer)
2559                 sdhci_pre_dma_transfer(host, mrq->data, COOKIE_PRE_MAPPED);
2560 }
2561
2562 static void sdhci_error_out_mrqs(struct sdhci_host *host, int err)
2563 {
2564         if (host->data_cmd) {
2565                 host->data_cmd->error = err;
2566                 sdhci_finish_mrq(host, host->data_cmd->mrq);
2567         }
2568
2569         if (host->cmd) {
2570                 host->cmd->error = err;
2571                 sdhci_finish_mrq(host, host->cmd->mrq);
2572         }
2573 }
2574
2575 static void sdhci_card_event(struct mmc_host *mmc)
2576 {
2577         struct sdhci_host *host = mmc_priv(mmc);
2578         unsigned long flags;
2579         int present;
2580
2581         /* First check if client has provided their own card event */
2582         if (host->ops->card_event)
2583                 host->ops->card_event(host);
2584
2585         present = mmc->ops->get_cd(mmc);
2586
2587         spin_lock_irqsave(&host->lock, flags);
2588
2589         /* Check sdhci_has_requests() first in case we are runtime suspended */
2590         if (sdhci_has_requests(host) && !present) {
2591                 pr_err("%s: Card removed during transfer!\n",
2592                         mmc_hostname(host->mmc));
2593                 pr_err("%s: Resetting controller.\n",
2594                         mmc_hostname(host->mmc));
2595
2596                 sdhci_do_reset(host, SDHCI_RESET_CMD);
2597                 sdhci_do_reset(host, SDHCI_RESET_DATA);
2598
2599                 sdhci_error_out_mrqs(host, -ENOMEDIUM);
2600         }
2601
2602         spin_unlock_irqrestore(&host->lock, flags);
2603 }
2604
2605 static const struct mmc_host_ops sdhci_ops = {
2606         .request        = sdhci_request,
2607         .post_req       = sdhci_post_req,
2608         .pre_req        = sdhci_pre_req,
2609         .set_ios        = sdhci_set_ios,
2610         .get_cd         = sdhci_get_cd,
2611         .get_ro         = sdhci_get_ro,
2612         .hw_reset       = sdhci_hw_reset,
2613         .enable_sdio_irq = sdhci_enable_sdio_irq,
2614         .ack_sdio_irq    = sdhci_ack_sdio_irq,
2615         .start_signal_voltage_switch    = sdhci_start_signal_voltage_switch,
2616         .prepare_hs400_tuning           = sdhci_prepare_hs400_tuning,
2617         .execute_tuning                 = sdhci_execute_tuning,
2618         .card_event                     = sdhci_card_event,
2619         .card_busy      = sdhci_card_busy,
2620 };
2621
2622 /*****************************************************************************\
2623  *                                                                           *
2624  * Request done                                                              *
2625  *                                                                           *
2626 \*****************************************************************************/
2627
2628 static bool sdhci_request_done(struct sdhci_host *host)
2629 {
2630         unsigned long flags;
2631         struct mmc_request *mrq;
2632         int i;
2633
2634         spin_lock_irqsave(&host->lock, flags);
2635
2636         for (i = 0; i < SDHCI_MAX_MRQS; i++) {
2637                 mrq = host->mrqs_done[i];
2638                 if (mrq)
2639                         break;
2640         }
2641
2642         if (!mrq) {
2643                 spin_unlock_irqrestore(&host->lock, flags);
2644                 return true;
2645         }
2646
2647         /*
2648          * Always unmap the data buffers if they were mapped by
2649          * sdhci_prepare_data() whenever we finish with a request.
2650          * This avoids leaking DMA mappings on error.
2651          */
2652         if (host->flags & SDHCI_REQ_USE_DMA) {
2653                 struct mmc_data *data = mrq->data;
2654
2655                 if (data && data->host_cookie == COOKIE_MAPPED) {
2656                         if (host->bounce_buffer) {
2657                                 /*
2658                                  * On reads, copy the bounced data into the
2659                                  * sglist
2660                                  */
2661                                 if (mmc_get_dma_dir(data) == DMA_FROM_DEVICE) {
2662                                         unsigned int length = data->bytes_xfered;
2663
2664                                         if (length > host->bounce_buffer_size) {
2665                                                 pr_err("%s: bounce buffer is %u bytes but DMA claims to have transferred %u bytes\n",
2666                                                        mmc_hostname(host->mmc),
2667                                                        host->bounce_buffer_size,
2668                                                        data->bytes_xfered);
2669                                                 /* Cap it down and continue */
2670                                                 length = host->bounce_buffer_size;
2671                                         }
2672                                         dma_sync_single_for_cpu(
2673                                                 host->mmc->parent,
2674                                                 host->bounce_addr,
2675                                                 host->bounce_buffer_size,
2676                                                 DMA_FROM_DEVICE);
2677                                         sg_copy_from_buffer(data->sg,
2678                                                 data->sg_len,
2679                                                 host->bounce_buffer,
2680                                                 length);
2681                                 } else {
2682                                         /* No copying, just switch ownership */
2683                                         dma_sync_single_for_cpu(
2684                                                 host->mmc->parent,
2685                                                 host->bounce_addr,
2686                                                 host->bounce_buffer_size,
2687                                                 mmc_get_dma_dir(data));
2688                                 }
2689                         } else {
2690                                 /* Unmap the raw data */
2691                                 dma_unmap_sg(mmc_dev(host->mmc), data->sg,
2692                                              data->sg_len,
2693                                              mmc_get_dma_dir(data));
2694                         }
2695                         data->host_cookie = COOKIE_UNMAPPED;
2696                 }
2697         }
2698
2699         /*
2700          * The controller needs a reset of internal state machines
2701          * upon error conditions.
2702          */
2703         if (sdhci_needs_reset(host, mrq)) {
2704                 /*
2705                  * Do not finish until command and data lines are available for
2706                  * reset. Note there can only be one other mrq, so it cannot
2707                  * also be in mrqs_done, otherwise host->cmd and host->data_cmd
2708                  * would both be null.
2709                  */
2710                 if (host->cmd || host->data_cmd) {
2711                         spin_unlock_irqrestore(&host->lock, flags);
2712                         return true;
2713                 }
2714
2715                 /* Some controllers need this kick or reset won't work here */
2716                 if (host->quirks & SDHCI_QUIRK_CLOCK_BEFORE_RESET)
2717                         /* This is to force an update */
2718                         host->ops->set_clock(host, host->clock);
2719
2720                 /* Spec says we should do both at the same time, but Ricoh
2721                    controllers do not like that. */
2722                 sdhci_do_reset(host, SDHCI_RESET_CMD);
2723                 sdhci_do_reset(host, SDHCI_RESET_DATA);
2724
2725                 host->pending_reset = false;
2726         }
2727
2728         host->mrqs_done[i] = NULL;
2729
2730         spin_unlock_irqrestore(&host->lock, flags);
2731
2732         mmc_request_done(host->mmc, mrq);
2733
2734         return false;
2735 }
2736
2737 static void sdhci_complete_work(struct work_struct *work)
2738 {
2739         struct sdhci_host *host = container_of(work, struct sdhci_host,
2740                                                complete_work);
2741
2742         while (!sdhci_request_done(host))
2743                 ;
2744 }
2745
2746 static void sdhci_timeout_timer(struct timer_list *t)
2747 {
2748         struct sdhci_host *host;
2749         unsigned long flags;
2750
2751         host = from_timer(host, t, timer);
2752
2753         spin_lock_irqsave(&host->lock, flags);
2754
2755         if (host->cmd && !sdhci_data_line_cmd(host->cmd)) {
2756                 pr_err("%s: Timeout waiting for hardware cmd interrupt.\n",
2757                        mmc_hostname(host->mmc));
2758                 sdhci_dumpregs(host);
2759
2760                 host->cmd->error = -ETIMEDOUT;
2761                 sdhci_finish_mrq(host, host->cmd->mrq);
2762         }
2763
2764         spin_unlock_irqrestore(&host->lock, flags);
2765 }
2766
2767 static void sdhci_timeout_data_timer(struct timer_list *t)
2768 {
2769         struct sdhci_host *host;
2770         unsigned long flags;
2771
2772         host = from_timer(host, t, data_timer);
2773
2774         spin_lock_irqsave(&host->lock, flags);
2775
2776         if (host->data || host->data_cmd ||
2777             (host->cmd && sdhci_data_line_cmd(host->cmd))) {
2778                 pr_err("%s: Timeout waiting for hardware interrupt.\n",
2779                        mmc_hostname(host->mmc));
2780                 sdhci_dumpregs(host);
2781
2782                 if (host->data) {
2783                         host->data->error = -ETIMEDOUT;
2784                         sdhci_finish_data(host);
2785                         queue_work(host->complete_wq, &host->complete_work);
2786                 } else if (host->data_cmd) {
2787                         host->data_cmd->error = -ETIMEDOUT;
2788                         sdhci_finish_mrq(host, host->data_cmd->mrq);
2789                 } else {
2790                         host->cmd->error = -ETIMEDOUT;
2791                         sdhci_finish_mrq(host, host->cmd->mrq);
2792                 }
2793         }
2794
2795         spin_unlock_irqrestore(&host->lock, flags);
2796 }
2797
2798 /*****************************************************************************\
2799  *                                                                           *
2800  * Interrupt handling                                                        *
2801  *                                                                           *
2802 \*****************************************************************************/
2803
2804 static void sdhci_cmd_irq(struct sdhci_host *host, u32 intmask, u32 *intmask_p)
2805 {
2806         /* Handle auto-CMD12 error */
2807         if (intmask & SDHCI_INT_AUTO_CMD_ERR && host->data_cmd) {
2808                 struct mmc_request *mrq = host->data_cmd->mrq;
2809                 u16 auto_cmd_status = sdhci_readw(host, SDHCI_AUTO_CMD_STATUS);
2810                 int data_err_bit = (auto_cmd_status & SDHCI_AUTO_CMD_TIMEOUT) ?
2811                                    SDHCI_INT_DATA_TIMEOUT :
2812                                    SDHCI_INT_DATA_CRC;
2813
2814                 /* Treat auto-CMD12 error the same as data error */
2815                 if (!mrq->sbc && (host->flags & SDHCI_AUTO_CMD12)) {
2816                         *intmask_p |= data_err_bit;
2817                         return;
2818                 }
2819         }
2820
2821         if (!host->cmd) {
2822                 /*
2823                  * SDHCI recovers from errors by resetting the cmd and data
2824                  * circuits.  Until that is done, there very well might be more
2825                  * interrupts, so ignore them in that case.
2826                  */
2827                 if (host->pending_reset)
2828                         return;
2829                 pr_err("%s: Got command interrupt 0x%08x even though no command operation was in progress.\n",
2830                        mmc_hostname(host->mmc), (unsigned)intmask);
2831                 sdhci_dumpregs(host);
2832                 return;
2833         }
2834
2835         if (intmask & (SDHCI_INT_TIMEOUT | SDHCI_INT_CRC |
2836                        SDHCI_INT_END_BIT | SDHCI_INT_INDEX)) {
2837                 if (intmask & SDHCI_INT_TIMEOUT)
2838                         host->cmd->error = -ETIMEDOUT;
2839                 else
2840                         host->cmd->error = -EILSEQ;
2841
2842                 /* Treat data command CRC error the same as data CRC error */
2843                 if (host->cmd->data &&
2844                     (intmask & (SDHCI_INT_CRC | SDHCI_INT_TIMEOUT)) ==
2845                      SDHCI_INT_CRC) {
2846                         host->cmd = NULL;
2847                         *intmask_p |= SDHCI_INT_DATA_CRC;
2848                         return;
2849                 }
2850
2851                 __sdhci_finish_mrq(host, host->cmd->mrq);
2852                 return;
2853         }
2854
2855         /* Handle auto-CMD23 error */
2856         if (intmask & SDHCI_INT_AUTO_CMD_ERR) {
2857                 struct mmc_request *mrq = host->cmd->mrq;
2858                 u16 auto_cmd_status = sdhci_readw(host, SDHCI_AUTO_CMD_STATUS);
2859                 int err = (auto_cmd_status & SDHCI_AUTO_CMD_TIMEOUT) ?
2860                           -ETIMEDOUT :
2861                           -EILSEQ;
2862
2863                 if (mrq->sbc && (host->flags & SDHCI_AUTO_CMD23)) {
2864                         mrq->sbc->error = err;
2865                         __sdhci_finish_mrq(host, mrq);
2866                         return;
2867                 }
2868         }
2869
2870         if (intmask & SDHCI_INT_RESPONSE)
2871                 sdhci_finish_command(host);
2872 }
2873
2874 static void sdhci_adma_show_error(struct sdhci_host *host)
2875 {
2876         void *desc = host->adma_table;
2877         dma_addr_t dma = host->adma_addr;
2878
2879         sdhci_dumpregs(host);
2880
2881         while (true) {
2882                 struct sdhci_adma2_64_desc *dma_desc = desc;
2883
2884                 if (host->flags & SDHCI_USE_64_BIT_DMA)
2885                         SDHCI_DUMP("%08llx: DMA 0x%08x%08x, LEN 0x%04x, Attr=0x%02x\n",
2886                             (unsigned long long)dma,
2887                             le32_to_cpu(dma_desc->addr_hi),
2888                             le32_to_cpu(dma_desc->addr_lo),
2889                             le16_to_cpu(dma_desc->len),
2890                             le16_to_cpu(dma_desc->cmd));
2891                 else
2892                         SDHCI_DUMP("%08llx: DMA 0x%08x, LEN 0x%04x, Attr=0x%02x\n",
2893                             (unsigned long long)dma,
2894                             le32_to_cpu(dma_desc->addr_lo),
2895                             le16_to_cpu(dma_desc->len),
2896                             le16_to_cpu(dma_desc->cmd));
2897
2898                 desc += host->desc_sz;
2899                 dma += host->desc_sz;
2900
2901                 if (dma_desc->cmd & cpu_to_le16(ADMA2_END))
2902                         break;
2903         }
2904 }
2905
2906 static void sdhci_data_irq(struct sdhci_host *host, u32 intmask)
2907 {
2908         u32 command;
2909
2910         /* CMD19 generates _only_ Buffer Read Ready interrupt */
2911         if (intmask & SDHCI_INT_DATA_AVAIL) {
2912                 command = SDHCI_GET_CMD(sdhci_readw(host, SDHCI_COMMAND));
2913                 if (command == MMC_SEND_TUNING_BLOCK ||
2914                     command == MMC_SEND_TUNING_BLOCK_HS200) {
2915                         host->tuning_done = 1;
2916                         wake_up(&host->buf_ready_int);
2917                         return;
2918                 }
2919         }
2920
2921         if (!host->data) {
2922                 struct mmc_command *data_cmd = host->data_cmd;
2923
2924                 /*
2925                  * The "data complete" interrupt is also used to
2926                  * indicate that a busy state has ended. See comment
2927                  * above in sdhci_cmd_irq().
2928                  */
2929                 if (data_cmd && (data_cmd->flags & MMC_RSP_BUSY)) {
2930                         if (intmask & SDHCI_INT_DATA_TIMEOUT) {
2931                                 host->data_cmd = NULL;
2932                                 data_cmd->error = -ETIMEDOUT;
2933                                 __sdhci_finish_mrq(host, data_cmd->mrq);
2934                                 return;
2935                         }
2936                         if (intmask & SDHCI_INT_DATA_END) {
2937                                 host->data_cmd = NULL;
2938                                 /*
2939                                  * Some cards handle busy-end interrupt
2940                                  * before the command completed, so make
2941                                  * sure we do things in the proper order.
2942                                  */
2943                                 if (host->cmd == data_cmd)
2944                                         return;
2945
2946                                 __sdhci_finish_mrq(host, data_cmd->mrq);
2947                                 return;
2948                         }
2949                 }
2950
2951                 /*
2952                  * SDHCI recovers from errors by resetting the cmd and data
2953                  * circuits. Until that is done, there very well might be more
2954                  * interrupts, so ignore them in that case.
2955                  */
2956                 if (host->pending_reset)
2957                         return;
2958
2959                 pr_err("%s: Got data interrupt 0x%08x even though no data operation was in progress.\n",
2960                        mmc_hostname(host->mmc), (unsigned)intmask);
2961                 sdhci_dumpregs(host);
2962
2963                 return;
2964         }
2965
2966         if (intmask & SDHCI_INT_DATA_TIMEOUT)
2967                 host->data->error = -ETIMEDOUT;
2968         else if (intmask & SDHCI_INT_DATA_END_BIT)
2969                 host->data->error = -EILSEQ;
2970         else if ((intmask & SDHCI_INT_DATA_CRC) &&
2971                 SDHCI_GET_CMD(sdhci_readw(host, SDHCI_COMMAND))
2972                         != MMC_BUS_TEST_R)
2973                 host->data->error = -EILSEQ;
2974         else if (intmask & SDHCI_INT_ADMA_ERROR) {
2975                 pr_err("%s: ADMA error: 0x%08x\n", mmc_hostname(host->mmc),
2976                        intmask);
2977                 sdhci_adma_show_error(host);
2978                 host->data->error = -EIO;
2979                 if (host->ops->adma_workaround)
2980                         host->ops->adma_workaround(host, intmask);
2981         }
2982
2983         if (host->data->error)
2984                 sdhci_finish_data(host);
2985         else {
2986                 if (intmask & (SDHCI_INT_DATA_AVAIL | SDHCI_INT_SPACE_AVAIL))
2987                         sdhci_transfer_pio(host);
2988
2989                 /*
2990                  * We currently don't do anything fancy with DMA
2991                  * boundaries, but as we can't disable the feature
2992                  * we need to at least restart the transfer.
2993                  *
2994                  * According to the spec sdhci_readl(host, SDHCI_DMA_ADDRESS)
2995                  * should return a valid address to continue from, but as
2996                  * some controllers are faulty, don't trust them.
2997                  */
2998                 if (intmask & SDHCI_INT_DMA_END) {
2999                         dma_addr_t dmastart, dmanow;
3000
3001                         dmastart = sdhci_sdma_address(host);
3002                         dmanow = dmastart + host->data->bytes_xfered;
3003                         /*
3004                          * Force update to the next DMA block boundary.
3005                          */
3006                         dmanow = (dmanow &
3007                                 ~((dma_addr_t)SDHCI_DEFAULT_BOUNDARY_SIZE - 1)) +
3008                                 SDHCI_DEFAULT_BOUNDARY_SIZE;
3009                         host->data->bytes_xfered = dmanow - dmastart;
3010                         DBG("DMA base %pad, transferred 0x%06x bytes, next %pad\n",
3011                             &dmastart, host->data->bytes_xfered, &dmanow);
3012                         sdhci_set_sdma_addr(host, dmanow);
3013                 }
3014
3015                 if (intmask & SDHCI_INT_DATA_END) {
3016                         if (host->cmd == host->data_cmd) {
3017                                 /*
3018                                  * Data managed to finish before the
3019                                  * command completed. Make sure we do
3020                                  * things in the proper order.
3021                                  */
3022                                 host->data_early = 1;
3023                         } else {
3024                                 sdhci_finish_data(host);
3025                         }
3026                 }
3027         }
3028 }
3029
3030 static inline bool sdhci_defer_done(struct sdhci_host *host,
3031                                     struct mmc_request *mrq)
3032 {
3033         struct mmc_data *data = mrq->data;
3034
3035         return host->pending_reset ||
3036                ((host->flags & SDHCI_REQ_USE_DMA) && data &&
3037                 data->host_cookie == COOKIE_MAPPED);
3038 }
3039
3040 static irqreturn_t sdhci_irq(int irq, void *dev_id)
3041 {
3042         struct mmc_request *mrqs_done[SDHCI_MAX_MRQS] = {0};
3043         irqreturn_t result = IRQ_NONE;
3044         struct sdhci_host *host = dev_id;
3045         u32 intmask, mask, unexpected = 0;
3046         int max_loops = 16;
3047         int i;
3048
3049         spin_lock(&host->lock);
3050
3051         if (host->runtime_suspended) {
3052                 spin_unlock(&host->lock);
3053                 return IRQ_NONE;
3054         }
3055
3056         intmask = sdhci_readl(host, SDHCI_INT_STATUS);
3057         if (!intmask || intmask == 0xffffffff) {
3058                 result = IRQ_NONE;
3059                 goto out;
3060         }
3061
3062         do {
3063                 DBG("IRQ status 0x%08x\n", intmask);
3064
3065                 if (host->ops->irq) {
3066                         intmask = host->ops->irq(host, intmask);
3067                         if (!intmask)
3068                                 goto cont;
3069                 }
3070
3071                 /* Clear selected interrupts. */
3072                 mask = intmask & (SDHCI_INT_CMD_MASK | SDHCI_INT_DATA_MASK |
3073                                   SDHCI_INT_BUS_POWER);
3074                 sdhci_writel(host, mask, SDHCI_INT_STATUS);
3075
3076                 if (intmask & (SDHCI_INT_CARD_INSERT | SDHCI_INT_CARD_REMOVE)) {
3077                         u32 present = sdhci_readl(host, SDHCI_PRESENT_STATE) &
3078                                       SDHCI_CARD_PRESENT;
3079
3080                         /*
3081                          * There is a observation on i.mx esdhc.  INSERT
3082                          * bit will be immediately set again when it gets
3083                          * cleared, if a card is inserted.  We have to mask
3084                          * the irq to prevent interrupt storm which will
3085                          * freeze the system.  And the REMOVE gets the
3086                          * same situation.
3087                          *
3088                          * More testing are needed here to ensure it works
3089                          * for other platforms though.
3090                          */
3091                         host->ier &= ~(SDHCI_INT_CARD_INSERT |
3092                                        SDHCI_INT_CARD_REMOVE);
3093                         host->ier |= present ? SDHCI_INT_CARD_REMOVE :
3094                                                SDHCI_INT_CARD_INSERT;
3095                         sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
3096                         sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
3097
3098                         sdhci_writel(host, intmask & (SDHCI_INT_CARD_INSERT |
3099                                      SDHCI_INT_CARD_REMOVE), SDHCI_INT_STATUS);
3100
3101                         host->thread_isr |= intmask & (SDHCI_INT_CARD_INSERT |
3102                                                        SDHCI_INT_CARD_REMOVE);
3103                         result = IRQ_WAKE_THREAD;
3104                 }
3105
3106                 if (intmask & SDHCI_INT_CMD_MASK)
3107                         sdhci_cmd_irq(host, intmask & SDHCI_INT_CMD_MASK, &intmask);
3108
3109                 if (intmask & SDHCI_INT_DATA_MASK)
3110                         sdhci_data_irq(host, intmask & SDHCI_INT_DATA_MASK);
3111
3112                 if (intmask & SDHCI_INT_BUS_POWER)
3113                         pr_err("%s: Card is consuming too much power!\n",
3114                                 mmc_hostname(host->mmc));
3115
3116                 if (intmask & SDHCI_INT_RETUNE)
3117                         mmc_retune_needed(host->mmc);
3118
3119                 if ((intmask & SDHCI_INT_CARD_INT) &&
3120                     (host->ier & SDHCI_INT_CARD_INT)) {
3121                         sdhci_enable_sdio_irq_nolock(host, false);
3122                         sdio_signal_irq(host->mmc);
3123                 }
3124
3125                 intmask &= ~(SDHCI_INT_CARD_INSERT | SDHCI_INT_CARD_REMOVE |
3126                              SDHCI_INT_CMD_MASK | SDHCI_INT_DATA_MASK |
3127                              SDHCI_INT_ERROR | SDHCI_INT_BUS_POWER |
3128                              SDHCI_INT_RETUNE | SDHCI_INT_CARD_INT);
3129
3130                 if (intmask) {
3131                         unexpected |= intmask;
3132                         sdhci_writel(host, intmask, SDHCI_INT_STATUS);
3133                 }
3134 cont:
3135                 if (result == IRQ_NONE)
3136                         result = IRQ_HANDLED;
3137
3138                 intmask = sdhci_readl(host, SDHCI_INT_STATUS);
3139         } while (intmask && --max_loops);
3140
3141         /* Determine if mrqs can be completed immediately */
3142         for (i = 0; i < SDHCI_MAX_MRQS; i++) {
3143                 struct mmc_request *mrq = host->mrqs_done[i];
3144
3145                 if (!mrq)
3146                         continue;
3147
3148                 if (sdhci_defer_done(host, mrq)) {
3149                         result = IRQ_WAKE_THREAD;
3150                 } else {
3151                         mrqs_done[i] = mrq;
3152                         host->mrqs_done[i] = NULL;
3153                 }
3154         }
3155 out:
3156         spin_unlock(&host->lock);
3157
3158         /* Process mrqs ready for immediate completion */
3159         for (i = 0; i < SDHCI_MAX_MRQS; i++) {
3160                 if (mrqs_done[i])
3161                         mmc_request_done(host->mmc, mrqs_done[i]);
3162         }
3163
3164         if (unexpected) {
3165                 pr_err("%s: Unexpected interrupt 0x%08x.\n",
3166                            mmc_hostname(host->mmc), unexpected);
3167                 sdhci_dumpregs(host);
3168         }
3169
3170         return result;
3171 }
3172
3173 static irqreturn_t sdhci_thread_irq(int irq, void *dev_id)
3174 {
3175         struct sdhci_host *host = dev_id;
3176         unsigned long flags;
3177         u32 isr;
3178
3179         while (!sdhci_request_done(host))
3180                 ;
3181
3182         spin_lock_irqsave(&host->lock, flags);
3183         isr = host->thread_isr;
3184         host->thread_isr = 0;
3185         spin_unlock_irqrestore(&host->lock, flags);
3186
3187         if (isr & (SDHCI_INT_CARD_INSERT | SDHCI_INT_CARD_REMOVE)) {
3188                 struct mmc_host *mmc = host->mmc;
3189
3190                 mmc->ops->card_event(mmc);
3191                 mmc_detect_change(mmc, msecs_to_jiffies(200));
3192         }
3193
3194         return IRQ_HANDLED;
3195 }
3196
3197 /*****************************************************************************\
3198  *                                                                           *
3199  * Suspend/resume                                                            *
3200  *                                                                           *
3201 \*****************************************************************************/
3202
3203 #ifdef CONFIG_PM
3204
3205 static bool sdhci_cd_irq_can_wakeup(struct sdhci_host *host)
3206 {
3207         return mmc_card_is_removable(host->mmc) &&
3208                !(host->quirks & SDHCI_QUIRK_BROKEN_CARD_DETECTION) &&
3209                !mmc_can_gpio_cd(host->mmc);
3210 }
3211
3212 /*
3213  * To enable wakeup events, the corresponding events have to be enabled in
3214  * the Interrupt Status Enable register too. See 'Table 1-6: Wakeup Signal
3215  * Table' in the SD Host Controller Standard Specification.
3216  * It is useless to restore SDHCI_INT_ENABLE state in
3217  * sdhci_disable_irq_wakeups() since it will be set by
3218  * sdhci_enable_card_detection() or sdhci_init().
3219  */
3220 static bool sdhci_enable_irq_wakeups(struct sdhci_host *host)
3221 {
3222         u8 mask = SDHCI_WAKE_ON_INSERT | SDHCI_WAKE_ON_REMOVE |
3223                   SDHCI_WAKE_ON_INT;
3224         u32 irq_val = 0;
3225         u8 wake_val = 0;
3226         u8 val;
3227
3228         if (sdhci_cd_irq_can_wakeup(host)) {
3229                 wake_val |= SDHCI_WAKE_ON_INSERT | SDHCI_WAKE_ON_REMOVE;
3230                 irq_val |= SDHCI_INT_CARD_INSERT | SDHCI_INT_CARD_REMOVE;
3231         }
3232
3233         if (mmc_card_wake_sdio_irq(host->mmc)) {
3234                 wake_val |= SDHCI_WAKE_ON_INT;
3235                 irq_val |= SDHCI_INT_CARD_INT;
3236         }
3237
3238         if (!irq_val)
3239                 return false;
3240
3241         val = sdhci_readb(host, SDHCI_WAKE_UP_CONTROL);
3242         val &= ~mask;
3243         val |= wake_val;
3244         sdhci_writeb(host, val, SDHCI_WAKE_UP_CONTROL);
3245
3246         sdhci_writel(host, irq_val, SDHCI_INT_ENABLE);
3247
3248         host->irq_wake_enabled = !enable_irq_wake(host->irq);
3249
3250         return host->irq_wake_enabled;
3251 }
3252
3253 static void sdhci_disable_irq_wakeups(struct sdhci_host *host)
3254 {
3255         u8 val;
3256         u8 mask = SDHCI_WAKE_ON_INSERT | SDHCI_WAKE_ON_REMOVE
3257                         | SDHCI_WAKE_ON_INT;
3258
3259         val = sdhci_readb(host, SDHCI_WAKE_UP_CONTROL);
3260         val &= ~mask;
3261         sdhci_writeb(host, val, SDHCI_WAKE_UP_CONTROL);
3262
3263         disable_irq_wake(host->irq);
3264
3265         host->irq_wake_enabled = false;
3266 }
3267
3268 int sdhci_suspend_host(struct sdhci_host *host)
3269 {
3270         sdhci_disable_card_detection(host);
3271
3272         mmc_retune_timer_stop(host->mmc);
3273
3274         if (!device_may_wakeup(mmc_dev(host->mmc)) ||
3275             !sdhci_enable_irq_wakeups(host)) {
3276                 host->ier = 0;
3277                 sdhci_writel(host, 0, SDHCI_INT_ENABLE);
3278                 sdhci_writel(host, 0, SDHCI_SIGNAL_ENABLE);
3279                 free_irq(host->irq, host);
3280         }
3281
3282         return 0;
3283 }
3284
3285 EXPORT_SYMBOL_GPL(sdhci_suspend_host);
3286
3287 int sdhci_resume_host(struct sdhci_host *host)
3288 {
3289         struct mmc_host *mmc = host->mmc;
3290         int ret = 0;
3291
3292         if (host->flags & (SDHCI_USE_SDMA | SDHCI_USE_ADMA)) {
3293                 if (host->ops->enable_dma)
3294                         host->ops->enable_dma(host);
3295         }
3296
3297         if ((host->mmc->pm_flags & MMC_PM_KEEP_POWER) &&
3298             (host->quirks2 & SDHCI_QUIRK2_HOST_OFF_CARD_ON)) {
3299                 /* Card keeps power but host controller does not */
3300                 sdhci_init(host, 0);
3301                 host->pwr = 0;
3302                 host->clock = 0;
3303                 mmc->ops->set_ios(mmc, &mmc->ios);
3304         } else {
3305                 sdhci_init(host, (host->mmc->pm_flags & MMC_PM_KEEP_POWER));
3306         }
3307
3308         if (host->irq_wake_enabled) {
3309                 sdhci_disable_irq_wakeups(host);
3310         } else {
3311                 ret = request_threaded_irq(host->irq, sdhci_irq,
3312                                            sdhci_thread_irq, IRQF_SHARED,
3313                                            mmc_hostname(host->mmc), host);
3314                 if (ret)
3315                         return ret;
3316         }
3317
3318         sdhci_enable_card_detection(host);
3319
3320         return ret;
3321 }
3322
3323 EXPORT_SYMBOL_GPL(sdhci_resume_host);
3324
3325 int sdhci_runtime_suspend_host(struct sdhci_host *host)
3326 {
3327         unsigned long flags;
3328
3329         mmc_retune_timer_stop(host->mmc);
3330
3331         spin_lock_irqsave(&host->lock, flags);
3332         host->ier &= SDHCI_INT_CARD_INT;
3333         sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
3334         sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
3335         spin_unlock_irqrestore(&host->lock, flags);
3336
3337         synchronize_hardirq(host->irq);
3338
3339         spin_lock_irqsave(&host->lock, flags);
3340         host->runtime_suspended = true;
3341         spin_unlock_irqrestore(&host->lock, flags);
3342
3343         return 0;
3344 }
3345 EXPORT_SYMBOL_GPL(sdhci_runtime_suspend_host);
3346
3347 int sdhci_runtime_resume_host(struct sdhci_host *host, int soft_reset)
3348 {
3349         struct mmc_host *mmc = host->mmc;
3350         unsigned long flags;
3351         int host_flags = host->flags;
3352
3353         if (host_flags & (SDHCI_USE_SDMA | SDHCI_USE_ADMA)) {
3354                 if (host->ops->enable_dma)
3355                         host->ops->enable_dma(host);
3356         }
3357
3358         sdhci_init(host, soft_reset);
3359
3360         if (mmc->ios.power_mode != MMC_POWER_UNDEFINED &&
3361             mmc->ios.power_mode != MMC_POWER_OFF) {
3362                 /* Force clock and power re-program */
3363                 host->pwr = 0;
3364                 host->clock = 0;
3365                 mmc->ops->start_signal_voltage_switch(mmc, &mmc->ios);
3366                 mmc->ops->set_ios(mmc, &mmc->ios);
3367
3368                 if ((host_flags & SDHCI_PV_ENABLED) &&
3369                     !(host->quirks2 & SDHCI_QUIRK2_PRESET_VALUE_BROKEN)) {
3370                         spin_lock_irqsave(&host->lock, flags);
3371                         sdhci_enable_preset_value(host, true);
3372                         spin_unlock_irqrestore(&host->lock, flags);
3373                 }
3374
3375                 if ((mmc->caps2 & MMC_CAP2_HS400_ES) &&
3376                     mmc->ops->hs400_enhanced_strobe)
3377                         mmc->ops->hs400_enhanced_strobe(mmc, &mmc->ios);
3378         }
3379
3380         spin_lock_irqsave(&host->lock, flags);
3381
3382         host->runtime_suspended = false;
3383
3384         /* Enable SDIO IRQ */
3385         if (sdio_irq_claimed(mmc))
3386                 sdhci_enable_sdio_irq_nolock(host, true);
3387
3388         /* Enable Card Detection */
3389         sdhci_enable_card_detection(host);
3390
3391         spin_unlock_irqrestore(&host->lock, flags);
3392
3393         return 0;
3394 }
3395 EXPORT_SYMBOL_GPL(sdhci_runtime_resume_host);
3396
3397 #endif /* CONFIG_PM */
3398
3399 /*****************************************************************************\
3400  *                                                                           *
3401  * Command Queue Engine (CQE) helpers                                        *
3402  *                                                                           *
3403 \*****************************************************************************/
3404
3405 void sdhci_cqe_enable(struct mmc_host *mmc)
3406 {
3407         struct sdhci_host *host = mmc_priv(mmc);
3408         unsigned long flags;
3409         u8 ctrl;
3410
3411         spin_lock_irqsave(&host->lock, flags);
3412
3413         ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
3414         ctrl &= ~SDHCI_CTRL_DMA_MASK;
3415         /*
3416          * Host from V4.10 supports ADMA3 DMA type.
3417          * ADMA3 performs integrated descriptor which is more suitable
3418          * for cmd queuing to fetch both command and transfer descriptors.
3419          */
3420         if (host->v4_mode && (host->caps1 & SDHCI_CAN_DO_ADMA3))
3421                 ctrl |= SDHCI_CTRL_ADMA3;
3422         else if (host->flags & SDHCI_USE_64_BIT_DMA)
3423                 ctrl |= SDHCI_CTRL_ADMA64;
3424         else
3425                 ctrl |= SDHCI_CTRL_ADMA32;
3426         sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
3427
3428         sdhci_writew(host, SDHCI_MAKE_BLKSZ(host->sdma_boundary, 512),
3429                      SDHCI_BLOCK_SIZE);
3430
3431         /* Set maximum timeout */
3432         sdhci_set_timeout(host, NULL);
3433
3434         host->ier = host->cqe_ier;
3435
3436         sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
3437         sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
3438
3439         host->cqe_on = true;
3440
3441         pr_debug("%s: sdhci: CQE on, IRQ mask %#x, IRQ status %#x\n",
3442                  mmc_hostname(mmc), host->ier,
3443                  sdhci_readl(host, SDHCI_INT_STATUS));
3444
3445         spin_unlock_irqrestore(&host->lock, flags);
3446 }
3447 EXPORT_SYMBOL_GPL(sdhci_cqe_enable);
3448
3449 void sdhci_cqe_disable(struct mmc_host *mmc, bool recovery)
3450 {
3451         struct sdhci_host *host = mmc_priv(mmc);
3452         unsigned long flags;
3453
3454         spin_lock_irqsave(&host->lock, flags);
3455
3456         sdhci_set_default_irqs(host);
3457
3458         host->cqe_on = false;
3459
3460         if (recovery) {
3461                 sdhci_do_reset(host, SDHCI_RESET_CMD);
3462                 sdhci_do_reset(host, SDHCI_RESET_DATA);
3463         }
3464
3465         pr_debug("%s: sdhci: CQE off, IRQ mask %#x, IRQ status %#x\n",
3466                  mmc_hostname(mmc), host->ier,
3467                  sdhci_readl(host, SDHCI_INT_STATUS));
3468
3469         spin_unlock_irqrestore(&host->lock, flags);
3470 }
3471 EXPORT_SYMBOL_GPL(sdhci_cqe_disable);
3472
3473 bool sdhci_cqe_irq(struct sdhci_host *host, u32 intmask, int *cmd_error,
3474                    int *data_error)
3475 {
3476         u32 mask;
3477
3478         if (!host->cqe_on)
3479                 return false;
3480
3481         if (intmask & (SDHCI_INT_INDEX | SDHCI_INT_END_BIT | SDHCI_INT_CRC))
3482                 *cmd_error = -EILSEQ;
3483         else if (intmask & SDHCI_INT_TIMEOUT)
3484                 *cmd_error = -ETIMEDOUT;
3485         else
3486                 *cmd_error = 0;
3487
3488         if (intmask & (SDHCI_INT_DATA_END_BIT | SDHCI_INT_DATA_CRC))
3489                 *data_error = -EILSEQ;
3490         else if (intmask & SDHCI_INT_DATA_TIMEOUT)
3491                 *data_error = -ETIMEDOUT;
3492         else if (intmask & SDHCI_INT_ADMA_ERROR)
3493                 *data_error = -EIO;
3494         else
3495                 *data_error = 0;
3496
3497         /* Clear selected interrupts. */
3498         mask = intmask & host->cqe_ier;
3499         sdhci_writel(host, mask, SDHCI_INT_STATUS);
3500
3501         if (intmask & SDHCI_INT_BUS_POWER)
3502                 pr_err("%s: Card is consuming too much power!\n",
3503                        mmc_hostname(host->mmc));
3504
3505         intmask &= ~(host->cqe_ier | SDHCI_INT_ERROR);
3506         if (intmask) {
3507                 sdhci_writel(host, intmask, SDHCI_INT_STATUS);
3508                 pr_err("%s: CQE: Unexpected interrupt 0x%08x.\n",
3509                        mmc_hostname(host->mmc), intmask);
3510                 sdhci_dumpregs(host);
3511         }
3512
3513         return true;
3514 }
3515 EXPORT_SYMBOL_GPL(sdhci_cqe_irq);
3516
3517 /*****************************************************************************\
3518  *                                                                           *
3519  * Device allocation/registration                                            *
3520  *                                                                           *
3521 \*****************************************************************************/
3522
3523 struct sdhci_host *sdhci_alloc_host(struct device *dev,
3524         size_t priv_size)
3525 {
3526         struct mmc_host *mmc;
3527         struct sdhci_host *host;
3528
3529         WARN_ON(dev == NULL);
3530
3531         mmc = mmc_alloc_host(sizeof(struct sdhci_host) + priv_size, dev);
3532         if (!mmc)
3533                 return ERR_PTR(-ENOMEM);
3534
3535         host = mmc_priv(mmc);
3536         host->mmc = mmc;
3537         host->mmc_host_ops = sdhci_ops;
3538         mmc->ops = &host->mmc_host_ops;
3539
3540         host->flags = SDHCI_SIGNALING_330;
3541
3542         host->cqe_ier     = SDHCI_CQE_INT_MASK;
3543         host->cqe_err_ier = SDHCI_CQE_INT_ERR_MASK;
3544
3545         host->tuning_delay = -1;
3546         host->tuning_loop_count = MAX_TUNING_LOOP;
3547
3548         host->sdma_boundary = SDHCI_DEFAULT_BOUNDARY_ARG;
3549
3550         /*
3551          * The DMA table descriptor count is calculated as the maximum
3552          * number of segments times 2, to allow for an alignment
3553          * descriptor for each segment, plus 1 for a nop end descriptor.
3554          */
3555         host->adma_table_cnt = SDHCI_MAX_SEGS * 2 + 1;
3556
3557         return host;
3558 }
3559
3560 EXPORT_SYMBOL_GPL(sdhci_alloc_host);
3561
3562 static int sdhci_set_dma_mask(struct sdhci_host *host)
3563 {
3564         struct mmc_host *mmc = host->mmc;
3565         struct device *dev = mmc_dev(mmc);
3566         int ret = -EINVAL;
3567
3568         if (host->quirks2 & SDHCI_QUIRK2_BROKEN_64_BIT_DMA)
3569                 host->flags &= ~SDHCI_USE_64_BIT_DMA;
3570
3571         /* Try 64-bit mask if hardware is capable  of it */
3572         if (host->flags & SDHCI_USE_64_BIT_DMA) {
3573                 ret = dma_set_mask_and_coherent(dev, DMA_BIT_MASK(64));
3574                 if (ret) {
3575                         pr_warn("%s: Failed to set 64-bit DMA mask.\n",
3576                                 mmc_hostname(mmc));
3577                         host->flags &= ~SDHCI_USE_64_BIT_DMA;
3578                 }
3579         }
3580
3581         /* 32-bit mask as default & fallback */
3582         if (ret) {
3583                 ret = dma_set_mask_and_coherent(dev, DMA_BIT_MASK(32));
3584                 if (ret)
3585                         pr_warn("%s: Failed to set 32-bit DMA mask.\n",
3586                                 mmc_hostname(mmc));
3587         }
3588
3589         return ret;
3590 }
3591
3592 void __sdhci_read_caps(struct sdhci_host *host, const u16 *ver,
3593                        const u32 *caps, const u32 *caps1)
3594 {
3595         u16 v;
3596         u64 dt_caps_mask = 0;
3597         u64 dt_caps = 0;
3598
3599         if (host->read_caps)
3600                 return;
3601
3602         host->read_caps = true;
3603
3604         if (debug_quirks)
3605                 host->quirks = debug_quirks;
3606
3607         if (debug_quirks2)
3608                 host->quirks2 = debug_quirks2;
3609
3610         sdhci_do_reset(host, SDHCI_RESET_ALL);
3611
3612         if (host->v4_mode)
3613                 sdhci_do_enable_v4_mode(host);
3614
3615         of_property_read_u64(mmc_dev(host->mmc)->of_node,
3616                              "sdhci-caps-mask", &dt_caps_mask);
3617         of_property_read_u64(mmc_dev(host->mmc)->of_node,
3618                              "sdhci-caps", &dt_caps);
3619
3620         v = ver ? *ver : sdhci_readw(host, SDHCI_HOST_VERSION);
3621         host->version = (v & SDHCI_SPEC_VER_MASK) >> SDHCI_SPEC_VER_SHIFT;
3622
3623         if (host->quirks & SDHCI_QUIRK_MISSING_CAPS)
3624                 return;
3625
3626         if (caps) {
3627                 host->caps = *caps;
3628         } else {
3629                 host->caps = sdhci_readl(host, SDHCI_CAPABILITIES);
3630                 host->caps &= ~lower_32_bits(dt_caps_mask);
3631                 host->caps |= lower_32_bits(dt_caps);
3632         }
3633
3634         if (host->version < SDHCI_SPEC_300)
3635                 return;
3636
3637         if (caps1) {
3638                 host->caps1 = *caps1;
3639         } else {
3640                 host->caps1 = sdhci_readl(host, SDHCI_CAPABILITIES_1);
3641                 host->caps1 &= ~upper_32_bits(dt_caps_mask);
3642                 host->caps1 |= upper_32_bits(dt_caps);
3643         }
3644 }
3645 EXPORT_SYMBOL_GPL(__sdhci_read_caps);
3646
3647 static void sdhci_allocate_bounce_buffer(struct sdhci_host *host)
3648 {
3649         struct mmc_host *mmc = host->mmc;
3650         unsigned int max_blocks;
3651         unsigned int bounce_size;
3652         int ret;
3653
3654         /*
3655          * Cap the bounce buffer at 64KB. Using a bigger bounce buffer
3656          * has diminishing returns, this is probably because SD/MMC
3657          * cards are usually optimized to handle this size of requests.
3658          */
3659         bounce_size = SZ_64K;
3660         /*
3661          * Adjust downwards to maximum request size if this is less
3662          * than our segment size, else hammer down the maximum
3663          * request size to the maximum buffer size.
3664          */
3665         if (mmc->max_req_size < bounce_size)
3666                 bounce_size = mmc->max_req_size;
3667         max_blocks = bounce_size / 512;
3668
3669         /*
3670          * When we just support one segment, we can get significant
3671          * speedups by the help of a bounce buffer to group scattered
3672          * reads/writes together.
3673          */
3674         host->bounce_buffer = devm_kmalloc(mmc->parent,
3675                                            bounce_size,
3676                                            GFP_KERNEL);
3677         if (!host->bounce_buffer) {
3678                 pr_err("%s: failed to allocate %u bytes for bounce buffer, falling back to single segments\n",
3679                        mmc_hostname(mmc),
3680                        bounce_size);
3681                 /*
3682                  * Exiting with zero here makes sure we proceed with
3683                  * mmc->max_segs == 1.
3684                  */
3685                 return;
3686         }
3687
3688         host->bounce_addr = dma_map_single(mmc->parent,
3689                                            host->bounce_buffer,
3690                                            bounce_size,
3691                                            DMA_BIDIRECTIONAL);
3692         ret = dma_mapping_error(mmc->parent, host->bounce_addr);
3693         if (ret)
3694                 /* Again fall back to max_segs == 1 */
3695                 return;
3696         host->bounce_buffer_size = bounce_size;
3697
3698         /* Lie about this since we're bouncing */
3699         mmc->max_segs = max_blocks;
3700         mmc->max_seg_size = bounce_size;
3701         mmc->max_req_size = bounce_size;
3702
3703         pr_info("%s bounce up to %u segments into one, max segment size %u bytes\n",
3704                 mmc_hostname(mmc), max_blocks, bounce_size);
3705 }
3706
3707 static inline bool sdhci_can_64bit_dma(struct sdhci_host *host)
3708 {
3709         /*
3710          * According to SD Host Controller spec v4.10, bit[27] added from
3711          * version 4.10 in Capabilities Register is used as 64-bit System
3712          * Address support for V4 mode.
3713          */
3714         if (host->version >= SDHCI_SPEC_410 && host->v4_mode)
3715                 return host->caps & SDHCI_CAN_64BIT_V4;
3716
3717         return host->caps & SDHCI_CAN_64BIT;
3718 }
3719
3720 int sdhci_setup_host(struct sdhci_host *host)
3721 {
3722         struct mmc_host *mmc;
3723         u32 max_current_caps;
3724         unsigned int ocr_avail;
3725         unsigned int override_timeout_clk;
3726         u32 max_clk;
3727         int ret;
3728
3729         WARN_ON(host == NULL);
3730         if (host == NULL)
3731                 return -EINVAL;
3732
3733         mmc = host->mmc;
3734
3735         /*
3736          * If there are external regulators, get them. Note this must be done
3737          * early before resetting the host and reading the capabilities so that
3738          * the host can take the appropriate action if regulators are not
3739          * available.
3740          */
3741         ret = mmc_regulator_get_supply(mmc);
3742         if (ret)
3743                 return ret;
3744
3745         DBG("Version:   0x%08x | Present:  0x%08x\n",
3746             sdhci_readw(host, SDHCI_HOST_VERSION),
3747             sdhci_readl(host, SDHCI_PRESENT_STATE));
3748         DBG("Caps:      0x%08x | Caps_1:   0x%08x\n",
3749             sdhci_readl(host, SDHCI_CAPABILITIES),
3750             sdhci_readl(host, SDHCI_CAPABILITIES_1));
3751
3752         sdhci_read_caps(host);
3753
3754         override_timeout_clk = host->timeout_clk;
3755
3756         if (host->version > SDHCI_SPEC_420) {
3757                 pr_err("%s: Unknown controller version (%d). You may experience problems.\n",
3758                        mmc_hostname(mmc), host->version);
3759         }
3760
3761         if (host->quirks & SDHCI_QUIRK_FORCE_DMA)
3762                 host->flags |= SDHCI_USE_SDMA;
3763         else if (!(host->caps & SDHCI_CAN_DO_SDMA))
3764                 DBG("Controller doesn't have SDMA capability\n");
3765         else
3766                 host->flags |= SDHCI_USE_SDMA;
3767
3768         if ((host->quirks & SDHCI_QUIRK_BROKEN_DMA) &&
3769                 (host->flags & SDHCI_USE_SDMA)) {
3770                 DBG("Disabling DMA as it is marked broken\n");
3771                 host->flags &= ~SDHCI_USE_SDMA;
3772         }
3773
3774         if ((host->version >= SDHCI_SPEC_200) &&
3775                 (host->caps & SDHCI_CAN_DO_ADMA2))
3776                 host->flags |= SDHCI_USE_ADMA;
3777
3778         if ((host->quirks & SDHCI_QUIRK_BROKEN_ADMA) &&
3779                 (host->flags & SDHCI_USE_ADMA)) {
3780                 DBG("Disabling ADMA as it is marked broken\n");
3781                 host->flags &= ~SDHCI_USE_ADMA;
3782         }
3783
3784         if (sdhci_can_64bit_dma(host))
3785                 host->flags |= SDHCI_USE_64_BIT_DMA;
3786
3787         if (host->flags & (SDHCI_USE_SDMA | SDHCI_USE_ADMA)) {
3788                 if (host->ops->set_dma_mask)
3789                         ret = host->ops->set_dma_mask(host);
3790                 else
3791                         ret = sdhci_set_dma_mask(host);
3792
3793                 if (!ret && host->ops->enable_dma)
3794                         ret = host->ops->enable_dma(host);
3795
3796                 if (ret) {
3797                         pr_warn("%s: No suitable DMA available - falling back to PIO\n",
3798                                 mmc_hostname(mmc));
3799                         host->flags &= ~(SDHCI_USE_SDMA | SDHCI_USE_ADMA);
3800
3801                         ret = 0;
3802                 }
3803         }
3804
3805         /* SDMA does not support 64-bit DMA if v4 mode not set */
3806         if ((host->flags & SDHCI_USE_64_BIT_DMA) && !host->v4_mode)
3807                 host->flags &= ~SDHCI_USE_SDMA;
3808
3809         if (host->flags & SDHCI_USE_ADMA) {
3810                 dma_addr_t dma;
3811                 void *buf;
3812
3813                 if (host->flags & SDHCI_USE_64_BIT_DMA) {
3814                         host->adma_table_sz = host->adma_table_cnt *
3815                                               SDHCI_ADMA2_64_DESC_SZ(host);
3816                         host->desc_sz = SDHCI_ADMA2_64_DESC_SZ(host);
3817                 } else {
3818                         host->adma_table_sz = host->adma_table_cnt *
3819                                               SDHCI_ADMA2_32_DESC_SZ;
3820                         host->desc_sz = SDHCI_ADMA2_32_DESC_SZ;
3821                 }
3822
3823                 host->align_buffer_sz = SDHCI_MAX_SEGS * SDHCI_ADMA2_ALIGN;
3824                 /*
3825                  * Use zalloc to zero the reserved high 32-bits of 128-bit
3826                  * descriptors so that they never need to be written.
3827                  */
3828                 buf = dma_alloc_coherent(mmc_dev(mmc),
3829                                          host->align_buffer_sz + host->adma_table_sz,
3830                                          &dma, GFP_KERNEL);
3831                 if (!buf) {
3832                         pr_warn("%s: Unable to allocate ADMA buffers - falling back to standard DMA\n",
3833                                 mmc_hostname(mmc));
3834                         host->flags &= ~SDHCI_USE_ADMA;
3835                 } else if ((dma + host->align_buffer_sz) &
3836                            (SDHCI_ADMA2_DESC_ALIGN - 1)) {
3837                         pr_warn("%s: unable to allocate aligned ADMA descriptor\n",
3838                                 mmc_hostname(mmc));
3839                         host->flags &= ~SDHCI_USE_ADMA;
3840                         dma_free_coherent(mmc_dev(mmc), host->align_buffer_sz +
3841                                           host->adma_table_sz, buf, dma);
3842                 } else {
3843                         host->align_buffer = buf;
3844                         host->align_addr = dma;
3845
3846                         host->adma_table = buf + host->align_buffer_sz;
3847                         host->adma_addr = dma + host->align_buffer_sz;
3848                 }
3849         }
3850
3851         /*
3852          * If we use DMA, then it's up to the caller to set the DMA
3853          * mask, but PIO does not need the hw shim so we set a new
3854          * mask here in that case.
3855          */
3856         if (!(host->flags & (SDHCI_USE_SDMA | SDHCI_USE_ADMA))) {
3857                 host->dma_mask = DMA_BIT_MASK(64);
3858                 mmc_dev(mmc)->dma_mask = &host->dma_mask;
3859         }
3860
3861         if (host->version >= SDHCI_SPEC_300)
3862                 host->max_clk = (host->caps & SDHCI_CLOCK_V3_BASE_MASK)
3863                         >> SDHCI_CLOCK_BASE_SHIFT;
3864         else
3865                 host->max_clk = (host->caps & SDHCI_CLOCK_BASE_MASK)
3866                         >> SDHCI_CLOCK_BASE_SHIFT;
3867
3868         host->max_clk *= 1000000;
3869         if (host->max_clk == 0 || host->quirks &
3870                         SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN) {
3871                 if (!host->ops->get_max_clock) {
3872                         pr_err("%s: Hardware doesn't specify base clock frequency.\n",
3873                                mmc_hostname(mmc));
3874                         ret = -ENODEV;
3875                         goto undma;
3876                 }
3877                 host->max_clk = host->ops->get_max_clock(host);
3878         }
3879
3880         /*
3881          * In case of Host Controller v3.00, find out whether clock
3882          * multiplier is supported.
3883          */
3884         host->clk_mul = (host->caps1 & SDHCI_CLOCK_MUL_MASK) >>
3885                         SDHCI_CLOCK_MUL_SHIFT;
3886
3887         /*
3888          * In case the value in Clock Multiplier is 0, then programmable
3889          * clock mode is not supported, otherwise the actual clock
3890          * multiplier is one more than the value of Clock Multiplier
3891          * in the Capabilities Register.
3892          */
3893         if (host->clk_mul)
3894                 host->clk_mul += 1;
3895
3896         /*
3897          * Set host parameters.
3898          */
3899         max_clk = host->max_clk;
3900
3901         if (host->ops->get_min_clock)
3902                 mmc->f_min = host->ops->get_min_clock(host);
3903         else if (host->version >= SDHCI_SPEC_300) {
3904                 if (host->clk_mul) {
3905                         mmc->f_min = (host->max_clk * host->clk_mul) / 1024;
3906                         max_clk = host->max_clk * host->clk_mul;
3907                 } else
3908                         mmc->f_min = host->max_clk / SDHCI_MAX_DIV_SPEC_300;
3909         } else
3910                 mmc->f_min = host->max_clk / SDHCI_MAX_DIV_SPEC_200;
3911
3912         if (!mmc->f_max || mmc->f_max > max_clk)
3913                 mmc->f_max = max_clk;
3914
3915         if (!(host->quirks & SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK)) {
3916                 host->timeout_clk = (host->caps & SDHCI_TIMEOUT_CLK_MASK) >>
3917                                         SDHCI_TIMEOUT_CLK_SHIFT;
3918
3919                 if (host->caps & SDHCI_TIMEOUT_CLK_UNIT)
3920                         host->timeout_clk *= 1000;
3921
3922                 if (host->timeout_clk == 0) {
3923                         if (!host->ops->get_timeout_clock) {
3924                                 pr_err("%s: Hardware doesn't specify timeout clock frequency.\n",
3925                                         mmc_hostname(mmc));
3926                                 ret = -ENODEV;
3927                                 goto undma;
3928                         }
3929
3930                         host->timeout_clk =
3931                                 DIV_ROUND_UP(host->ops->get_timeout_clock(host),
3932                                              1000);
3933                 }
3934
3935                 if (override_timeout_clk)
3936                         host->timeout_clk = override_timeout_clk;
3937
3938                 mmc->max_busy_timeout = host->ops->get_max_timeout_count ?
3939                         host->ops->get_max_timeout_count(host) : 1 << 27;
3940                 mmc->max_busy_timeout /= host->timeout_clk;
3941         }
3942
3943         if (host->quirks2 & SDHCI_QUIRK2_DISABLE_HW_TIMEOUT &&
3944             !host->ops->get_max_timeout_count)
3945                 mmc->max_busy_timeout = 0;
3946
3947         mmc->caps |= MMC_CAP_SDIO_IRQ | MMC_CAP_ERASE | MMC_CAP_CMD23;
3948         mmc->caps2 |= MMC_CAP2_SDIO_IRQ_NOTHREAD;
3949
3950         if (host->quirks & SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12)
3951                 host->flags |= SDHCI_AUTO_CMD12;
3952
3953         /*
3954          * For v3 mode, Auto-CMD23 stuff only works in ADMA or PIO.
3955          * For v4 mode, SDMA may use Auto-CMD23 as well.
3956          */
3957         if ((host->version >= SDHCI_SPEC_300) &&
3958             ((host->flags & SDHCI_USE_ADMA) ||
3959              !(host->flags & SDHCI_USE_SDMA) || host->v4_mode) &&
3960              !(host->quirks2 & SDHCI_QUIRK2_ACMD23_BROKEN)) {
3961                 host->flags |= SDHCI_AUTO_CMD23;
3962                 DBG("Auto-CMD23 available\n");
3963         } else {
3964                 DBG("Auto-CMD23 unavailable\n");
3965         }
3966
3967         /*
3968          * A controller may support 8-bit width, but the board itself
3969          * might not have the pins brought out.  Boards that support
3970          * 8-bit width must set "mmc->caps |= MMC_CAP_8_BIT_DATA;" in
3971          * their platform code before calling sdhci_add_host(), and we
3972          * won't assume 8-bit width for hosts without that CAP.
3973          */
3974         if (!(host->quirks & SDHCI_QUIRK_FORCE_1_BIT_DATA))
3975                 mmc->caps |= MMC_CAP_4_BIT_DATA;
3976
3977         if (host->quirks2 & SDHCI_QUIRK2_HOST_NO_CMD23)
3978                 mmc->caps &= ~MMC_CAP_CMD23;
3979
3980         if (host->caps & SDHCI_CAN_DO_HISPD)
3981                 mmc->caps |= MMC_CAP_SD_HIGHSPEED | MMC_CAP_MMC_HIGHSPEED;
3982
3983         if ((host->quirks & SDHCI_QUIRK_BROKEN_CARD_DETECTION) &&
3984             mmc_card_is_removable(mmc) &&
3985             mmc_gpio_get_cd(host->mmc) < 0)
3986                 mmc->caps |= MMC_CAP_NEEDS_POLL;
3987
3988         if (!IS_ERR(mmc->supply.vqmmc)) {
3989                 ret = regulator_enable(mmc->supply.vqmmc);
3990
3991                 /* If vqmmc provides no 1.8V signalling, then there's no UHS */
3992                 if (!regulator_is_supported_voltage(mmc->supply.vqmmc, 1700000,
3993                                                     1950000))
3994                         host->caps1 &= ~(SDHCI_SUPPORT_SDR104 |
3995                                          SDHCI_SUPPORT_SDR50 |
3996                                          SDHCI_SUPPORT_DDR50);
3997
3998                 /* In eMMC case vqmmc might be a fixed 1.8V regulator */
3999                 if (!regulator_is_supported_voltage(mmc->supply.vqmmc, 2700000,
4000                                                     3600000))
4001                         host->flags &= ~SDHCI_SIGNALING_330;
4002
4003                 if (ret) {
4004                         pr_warn("%s: Failed to enable vqmmc regulator: %d\n",
4005                                 mmc_hostname(mmc), ret);
4006                         mmc->supply.vqmmc = ERR_PTR(-EINVAL);
4007                 }
4008         }
4009
4010         if (host->quirks2 & SDHCI_QUIRK2_NO_1_8_V) {
4011                 host->caps1 &= ~(SDHCI_SUPPORT_SDR104 | SDHCI_SUPPORT_SDR50 |
4012                                  SDHCI_SUPPORT_DDR50);
4013                 /*
4014                  * The SDHCI controller in a SoC might support HS200/HS400
4015                  * (indicated using mmc-hs200-1_8v/mmc-hs400-1_8v dt property),
4016                  * but if the board is modeled such that the IO lines are not
4017                  * connected to 1.8v then HS200/HS400 cannot be supported.
4018                  * Disable HS200/HS400 if the board does not have 1.8v connected
4019                  * to the IO lines. (Applicable for other modes in 1.8v)
4020                  */
4021                 mmc->caps2 &= ~(MMC_CAP2_HSX00_1_8V | MMC_CAP2_HS400_ES);
4022                 mmc->caps &= ~(MMC_CAP_1_8V_DDR | MMC_CAP_UHS);
4023         }
4024
4025         /* Any UHS-I mode in caps implies SDR12 and SDR25 support. */
4026         if (host->caps1 & (SDHCI_SUPPORT_SDR104 | SDHCI_SUPPORT_SDR50 |
4027                            SDHCI_SUPPORT_DDR50))
4028                 mmc->caps |= MMC_CAP_UHS_SDR12 | MMC_CAP_UHS_SDR25;
4029
4030         /* SDR104 supports also implies SDR50 support */
4031         if (host->caps1 & SDHCI_SUPPORT_SDR104) {
4032                 mmc->caps |= MMC_CAP_UHS_SDR104 | MMC_CAP_UHS_SDR50;
4033                 /* SD3.0: SDR104 is supported so (for eMMC) the caps2
4034                  * field can be promoted to support HS200.
4035                  */
4036                 if (!(host->quirks2 & SDHCI_QUIRK2_BROKEN_HS200))
4037                         mmc->caps2 |= MMC_CAP2_HS200;
4038         } else if (host->caps1 & SDHCI_SUPPORT_SDR50) {
4039                 mmc->caps |= MMC_CAP_UHS_SDR50;
4040         }
4041
4042         if (host->quirks2 & SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400 &&
4043             (host->caps1 & SDHCI_SUPPORT_HS400))
4044                 mmc->caps2 |= MMC_CAP2_HS400;
4045
4046         if ((mmc->caps2 & MMC_CAP2_HSX00_1_2V) &&
4047             (IS_ERR(mmc->supply.vqmmc) ||
4048              !regulator_is_supported_voltage(mmc->supply.vqmmc, 1100000,
4049                                              1300000)))
4050                 mmc->caps2 &= ~MMC_CAP2_HSX00_1_2V;
4051
4052         if ((host->caps1 & SDHCI_SUPPORT_DDR50) &&
4053             !(host->quirks2 & SDHCI_QUIRK2_BROKEN_DDR50))
4054                 mmc->caps |= MMC_CAP_UHS_DDR50;
4055
4056         /* Does the host need tuning for SDR50? */
4057         if (host->caps1 & SDHCI_USE_SDR50_TUNING)
4058                 host->flags |= SDHCI_SDR50_NEEDS_TUNING;
4059
4060         /* Driver Type(s) (A, C, D) supported by the host */
4061         if (host->caps1 & SDHCI_DRIVER_TYPE_A)
4062                 mmc->caps |= MMC_CAP_DRIVER_TYPE_A;
4063         if (host->caps1 & SDHCI_DRIVER_TYPE_C)
4064                 mmc->caps |= MMC_CAP_DRIVER_TYPE_C;
4065         if (host->caps1 & SDHCI_DRIVER_TYPE_D)
4066                 mmc->caps |= MMC_CAP_DRIVER_TYPE_D;
4067
4068         /* Initial value for re-tuning timer count */
4069         host->tuning_count = (host->caps1 & SDHCI_RETUNING_TIMER_COUNT_MASK) >>
4070                              SDHCI_RETUNING_TIMER_COUNT_SHIFT;
4071
4072         /*
4073          * In case Re-tuning Timer is not disabled, the actual value of
4074          * re-tuning timer will be 2 ^ (n - 1).
4075          */
4076         if (host->tuning_count)
4077                 host->tuning_count = 1 << (host->tuning_count - 1);
4078
4079         /* Re-tuning mode supported by the Host Controller */
4080         host->tuning_mode = (host->caps1 & SDHCI_RETUNING_MODE_MASK) >>
4081                              SDHCI_RETUNING_MODE_SHIFT;
4082
4083         ocr_avail = 0;
4084
4085         /*
4086          * According to SD Host Controller spec v3.00, if the Host System
4087          * can afford more than 150mA, Host Driver should set XPC to 1. Also
4088          * the value is meaningful only if Voltage Support in the Capabilities
4089          * register is set. The actual current value is 4 times the register
4090          * value.
4091          */
4092         max_current_caps = sdhci_readl(host, SDHCI_MAX_CURRENT);
4093         if (!max_current_caps && !IS_ERR(mmc->supply.vmmc)) {
4094                 int curr = regulator_get_current_limit(mmc->supply.vmmc);
4095                 if (curr > 0) {
4096
4097                         /* convert to SDHCI_MAX_CURRENT format */
4098                         curr = curr/1000;  /* convert to mA */
4099                         curr = curr/SDHCI_MAX_CURRENT_MULTIPLIER;
4100
4101                         curr = min_t(u32, curr, SDHCI_MAX_CURRENT_LIMIT);
4102                         max_current_caps =
4103                                 (curr << SDHCI_MAX_CURRENT_330_SHIFT) |
4104                                 (curr << SDHCI_MAX_CURRENT_300_SHIFT) |
4105                                 (curr << SDHCI_MAX_CURRENT_180_SHIFT);
4106                 }
4107         }
4108
4109         if (host->caps & SDHCI_CAN_VDD_330) {
4110                 ocr_avail |= MMC_VDD_32_33 | MMC_VDD_33_34;
4111
4112                 mmc->max_current_330 = ((max_current_caps &
4113                                    SDHCI_MAX_CURRENT_330_MASK) >>
4114                                    SDHCI_MAX_CURRENT_330_SHIFT) *
4115                                    SDHCI_MAX_CURRENT_MULTIPLIER;
4116         }
4117         if (host->caps & SDHCI_CAN_VDD_300) {
4118                 ocr_avail |= MMC_VDD_29_30 | MMC_VDD_30_31;
4119
4120                 mmc->max_current_300 = ((max_current_caps &
4121                                    SDHCI_MAX_CURRENT_300_MASK) >>
4122                                    SDHCI_MAX_CURRENT_300_SHIFT) *
4123                                    SDHCI_MAX_CURRENT_MULTIPLIER;
4124         }
4125         if (host->caps & SDHCI_CAN_VDD_180) {
4126                 ocr_avail |= MMC_VDD_165_195;
4127
4128                 mmc->max_current_180 = ((max_current_caps &
4129                                    SDHCI_MAX_CURRENT_180_MASK) >>
4130                                    SDHCI_MAX_CURRENT_180_SHIFT) *
4131                                    SDHCI_MAX_CURRENT_MULTIPLIER;
4132         }
4133
4134         /* If OCR set by host, use it instead. */
4135         if (host->ocr_mask)
4136                 ocr_avail = host->ocr_mask;
4137
4138         /* If OCR set by external regulators, give it highest prio. */
4139         if (mmc->ocr_avail)
4140                 ocr_avail = mmc->ocr_avail;
4141
4142         mmc->ocr_avail = ocr_avail;
4143         mmc->ocr_avail_sdio = ocr_avail;
4144         if (host->ocr_avail_sdio)
4145                 mmc->ocr_avail_sdio &= host->ocr_avail_sdio;
4146         mmc->ocr_avail_sd = ocr_avail;
4147         if (host->ocr_avail_sd)
4148                 mmc->ocr_avail_sd &= host->ocr_avail_sd;
4149         else /* normal SD controllers don't support 1.8V */
4150                 mmc->ocr_avail_sd &= ~MMC_VDD_165_195;
4151         mmc->ocr_avail_mmc = ocr_avail;
4152         if (host->ocr_avail_mmc)
4153                 mmc->ocr_avail_mmc &= host->ocr_avail_mmc;
4154
4155         if (mmc->ocr_avail == 0) {
4156                 pr_err("%s: Hardware doesn't report any support voltages.\n",
4157                        mmc_hostname(mmc));
4158                 ret = -ENODEV;
4159                 goto unreg;
4160         }
4161
4162         if ((mmc->caps & (MMC_CAP_UHS_SDR12 | MMC_CAP_UHS_SDR25 |
4163                           MMC_CAP_UHS_SDR50 | MMC_CAP_UHS_SDR104 |
4164                           MMC_CAP_UHS_DDR50 | MMC_CAP_1_8V_DDR)) ||
4165             (mmc->caps2 & (MMC_CAP2_HS200_1_8V_SDR | MMC_CAP2_HS400_1_8V)))
4166                 host->flags |= SDHCI_SIGNALING_180;
4167
4168         if (mmc->caps2 & MMC_CAP2_HSX00_1_2V)
4169                 host->flags |= SDHCI_SIGNALING_120;
4170
4171         spin_lock_init(&host->lock);
4172
4173         /*
4174          * Maximum number of sectors in one transfer. Limited by SDMA boundary
4175          * size (512KiB). Note some tuning modes impose a 4MiB limit, but this
4176          * is less anyway.
4177          */
4178         mmc->max_req_size = 524288;
4179
4180         /*
4181          * Maximum number of segments. Depends on if the hardware
4182          * can do scatter/gather or not.
4183          */
4184         if (host->flags & SDHCI_USE_ADMA) {
4185                 mmc->max_segs = SDHCI_MAX_SEGS;
4186         } else if (host->flags & SDHCI_USE_SDMA) {
4187                 mmc->max_segs = 1;
4188                 if (swiotlb_max_segment()) {
4189                         unsigned int max_req_size = (1 << IO_TLB_SHIFT) *
4190                                                 IO_TLB_SEGSIZE;
4191                         mmc->max_req_size = min(mmc->max_req_size,
4192                                                 max_req_size);
4193                 }
4194         } else { /* PIO */
4195                 mmc->max_segs = SDHCI_MAX_SEGS;
4196         }
4197
4198         /*
4199          * Maximum segment size. Could be one segment with the maximum number
4200          * of bytes. When doing hardware scatter/gather, each entry cannot
4201          * be larger than 64 KiB though.
4202          */
4203         if (host->flags & SDHCI_USE_ADMA) {
4204                 if (host->quirks & SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC)
4205                         mmc->max_seg_size = 65535;
4206                 else
4207                         mmc->max_seg_size = 65536;
4208         } else {
4209                 mmc->max_seg_size = mmc->max_req_size;
4210         }
4211
4212         /*
4213          * Maximum block size. This varies from controller to controller and
4214          * is specified in the capabilities register.
4215          */
4216         if (host->quirks & SDHCI_QUIRK_FORCE_BLK_SZ_2048) {
4217                 mmc->max_blk_size = 2;
4218         } else {
4219                 mmc->max_blk_size = (host->caps & SDHCI_MAX_BLOCK_MASK) >>
4220                                 SDHCI_MAX_BLOCK_SHIFT;
4221                 if (mmc->max_blk_size >= 3) {
4222                         pr_warn("%s: Invalid maximum block size, assuming 512 bytes\n",
4223                                 mmc_hostname(mmc));
4224                         mmc->max_blk_size = 0;
4225                 }
4226         }
4227
4228         mmc->max_blk_size = 512 << mmc->max_blk_size;
4229
4230         /*
4231          * Maximum block count.
4232          */
4233         mmc->max_blk_count = (host->quirks & SDHCI_QUIRK_NO_MULTIBLOCK) ? 1 : 65535;
4234
4235         if (mmc->max_segs == 1)
4236                 /* This may alter mmc->*_blk_* parameters */
4237                 sdhci_allocate_bounce_buffer(host);
4238
4239         return 0;
4240
4241 unreg:
4242         if (!IS_ERR(mmc->supply.vqmmc))
4243                 regulator_disable(mmc->supply.vqmmc);
4244 undma:
4245         if (host->align_buffer)
4246                 dma_free_coherent(mmc_dev(mmc), host->align_buffer_sz +
4247                                   host->adma_table_sz, host->align_buffer,
4248                                   host->align_addr);
4249         host->adma_table = NULL;
4250         host->align_buffer = NULL;
4251
4252         return ret;
4253 }
4254 EXPORT_SYMBOL_GPL(sdhci_setup_host);
4255
4256 void sdhci_cleanup_host(struct sdhci_host *host)
4257 {
4258         struct mmc_host *mmc = host->mmc;
4259
4260         if (!IS_ERR(mmc->supply.vqmmc))
4261                 regulator_disable(mmc->supply.vqmmc);
4262
4263         if (host->align_buffer)
4264                 dma_free_coherent(mmc_dev(mmc), host->align_buffer_sz +
4265                                   host->adma_table_sz, host->align_buffer,
4266                                   host->align_addr);
4267         host->adma_table = NULL;
4268         host->align_buffer = NULL;
4269 }
4270 EXPORT_SYMBOL_GPL(sdhci_cleanup_host);
4271
4272 int __sdhci_add_host(struct sdhci_host *host)
4273 {
4274         unsigned int flags = WQ_UNBOUND | WQ_MEM_RECLAIM | WQ_HIGHPRI;
4275         struct mmc_host *mmc = host->mmc;
4276         int ret;
4277
4278         host->complete_wq = alloc_workqueue("sdhci", flags, 0);
4279         if (!host->complete_wq)
4280                 return -ENOMEM;
4281
4282         INIT_WORK(&host->complete_work, sdhci_complete_work);
4283
4284         timer_setup(&host->timer, sdhci_timeout_timer, 0);
4285         timer_setup(&host->data_timer, sdhci_timeout_data_timer, 0);
4286
4287         init_waitqueue_head(&host->buf_ready_int);
4288
4289         sdhci_init(host, 0);
4290
4291         ret = request_threaded_irq(host->irq, sdhci_irq, sdhci_thread_irq,
4292                                    IRQF_SHARED, mmc_hostname(mmc), host);
4293         if (ret) {
4294                 pr_err("%s: Failed to request IRQ %d: %d\n",
4295                        mmc_hostname(mmc), host->irq, ret);
4296                 goto unwq;
4297         }
4298
4299         ret = sdhci_led_register(host);
4300         if (ret) {
4301                 pr_err("%s: Failed to register LED device: %d\n",
4302                        mmc_hostname(mmc), ret);
4303                 goto unirq;
4304         }
4305
4306         ret = mmc_add_host(mmc);
4307         if (ret)
4308                 goto unled;
4309
4310         pr_info("%s: SDHCI controller on %s [%s] using %s\n",
4311                 mmc_hostname(mmc), host->hw_name, dev_name(mmc_dev(mmc)),
4312                 (host->flags & SDHCI_USE_ADMA) ?
4313                 (host->flags & SDHCI_USE_64_BIT_DMA) ? "ADMA 64-bit" : "ADMA" :
4314                 (host->flags & SDHCI_USE_SDMA) ? "DMA" : "PIO");
4315
4316         sdhci_enable_card_detection(host);
4317
4318         return 0;
4319
4320 unled:
4321         sdhci_led_unregister(host);
4322 unirq:
4323         sdhci_do_reset(host, SDHCI_RESET_ALL);
4324         sdhci_writel(host, 0, SDHCI_INT_ENABLE);
4325         sdhci_writel(host, 0, SDHCI_SIGNAL_ENABLE);
4326         free_irq(host->irq, host);
4327 unwq:
4328         destroy_workqueue(host->complete_wq);
4329
4330         return ret;
4331 }
4332 EXPORT_SYMBOL_GPL(__sdhci_add_host);
4333
4334 int sdhci_add_host(struct sdhci_host *host)
4335 {
4336         int ret;
4337
4338         ret = sdhci_setup_host(host);
4339         if (ret)
4340                 return ret;
4341
4342         ret = __sdhci_add_host(host);
4343         if (ret)
4344                 goto cleanup;
4345
4346         return 0;
4347
4348 cleanup:
4349         sdhci_cleanup_host(host);
4350
4351         return ret;
4352 }
4353 EXPORT_SYMBOL_GPL(sdhci_add_host);
4354
4355 void sdhci_remove_host(struct sdhci_host *host, int dead)
4356 {
4357         struct mmc_host *mmc = host->mmc;
4358         unsigned long flags;
4359
4360         if (dead) {
4361                 spin_lock_irqsave(&host->lock, flags);
4362
4363                 host->flags |= SDHCI_DEVICE_DEAD;
4364
4365                 if (sdhci_has_requests(host)) {
4366                         pr_err("%s: Controller removed during "
4367                                 " transfer!\n", mmc_hostname(mmc));
4368                         sdhci_error_out_mrqs(host, -ENOMEDIUM);
4369                 }
4370
4371                 spin_unlock_irqrestore(&host->lock, flags);
4372         }
4373
4374         sdhci_disable_card_detection(host);
4375
4376         mmc_remove_host(mmc);
4377
4378         sdhci_led_unregister(host);
4379
4380         if (!dead)
4381                 sdhci_do_reset(host, SDHCI_RESET_ALL);
4382
4383         sdhci_writel(host, 0, SDHCI_INT_ENABLE);
4384         sdhci_writel(host, 0, SDHCI_SIGNAL_ENABLE);
4385         free_irq(host->irq, host);
4386
4387         del_timer_sync(&host->timer);
4388         del_timer_sync(&host->data_timer);
4389
4390         destroy_workqueue(host->complete_wq);
4391
4392         if (!IS_ERR(mmc->supply.vqmmc))
4393                 regulator_disable(mmc->supply.vqmmc);
4394
4395         if (host->align_buffer)
4396                 dma_free_coherent(mmc_dev(mmc), host->align_buffer_sz +
4397                                   host->adma_table_sz, host->align_buffer,
4398                                   host->align_addr);
4399
4400         host->adma_table = NULL;
4401         host->align_buffer = NULL;
4402 }
4403
4404 EXPORT_SYMBOL_GPL(sdhci_remove_host);
4405
4406 void sdhci_free_host(struct sdhci_host *host)
4407 {
4408         mmc_free_host(host->mmc);
4409 }
4410
4411 EXPORT_SYMBOL_GPL(sdhci_free_host);
4412
4413 /*****************************************************************************\
4414  *                                                                           *
4415  * Driver init/exit                                                          *
4416  *                                                                           *
4417 \*****************************************************************************/
4418
4419 static int __init sdhci_drv_init(void)
4420 {
4421         pr_info(DRIVER_NAME
4422                 ": Secure Digital Host Controller Interface driver\n");
4423         pr_info(DRIVER_NAME ": Copyright(c) Pierre Ossman\n");
4424
4425         return 0;
4426 }
4427
4428 static void __exit sdhci_drv_exit(void)
4429 {
4430 }
4431
4432 module_init(sdhci_drv_init);
4433 module_exit(sdhci_drv_exit);
4434
4435 module_param(debug_quirks, uint, 0444);
4436 module_param(debug_quirks2, uint, 0444);
4437
4438 MODULE_AUTHOR("Pierre Ossman <[email protected]>");
4439 MODULE_DESCRIPTION("Secure Digital Host Controller Interface core driver");
4440 MODULE_LICENSE("GPL");
4441
4442 MODULE_PARM_DESC(debug_quirks, "Force certain quirks.");
4443 MODULE_PARM_DESC(debug_quirks2, "Force certain other quirks.");