drivers/usb/serial/ssu100.c

   1 /*
   2  * usb-serial driver for Quatech SSU-100
   3  *
   4  * based on ftdi_sio.c and the original serqt_usb.c from Quatech
   5  *
   6  */
   7
   8 #include <linux/errno.h>
   9 #include <linux/slab.h>
  10 #include <linux/tty.h>
  11 #include <linux/tty_driver.h>
  12 #include <linux/tty_flip.h>
  13 #include <linux/module.h>
  14 #include <linux/serial.h>
  15 #include <linux/usb.h>
  16 #include <linux/usb/serial.h>
  17 #include <linux/serial_reg.h>
  18 #include <linux/uaccess.h>
  19
  20 #define QT_OPEN_CLOSE_CHANNEL       0xca
  21 #define QT_SET_GET_DEVICE           0xc2
  22 #define QT_SET_GET_REGISTER         0xc0
  23 #define QT_GET_SET_PREBUF_TRIG_LVL  0xcc
  24 #define QT_SET_ATF                  0xcd
  25 #define QT_GET_SET_UART             0xc1
  26 #define QT_TRANSFER_IN              0xc0
  27 #define QT_HW_FLOW_CONTROL_MASK     0xc5
  28 #define QT_SW_FLOW_CONTROL_MASK     0xc6
  29
  30 #define  SERIAL_MSR_MASK            0xf0
  31
  32 #define  SERIAL_CRTSCTS ((UART_MCR_RTS << 8) | UART_MSR_CTS)
  33
  34 #define  SERIAL_EVEN_PARITY         (UART_LCR_PARITY | UART_LCR_EPAR)
  35
  36 #define  MAX_BAUD_RATE              460800
  37
  38 #define ATC_DISABLED                0x00
  39 #define DUPMODE_BITS        0xc0
  40 #define RR_BITS             0x03
  41 #define LOOPMODE_BITS       0x41
  42 #define RS232_MODE          0x00
  43 #define RTSCTS_TO_CONNECTOR 0x40
  44 #define CLKS_X4             0x02
  45 #define FULLPWRBIT          0x00000080
  46 #define NEXT_BOARD_POWER_BIT        0x00000004
  47
  48 #define DRIVER_DESC "Quatech SSU-100 USB to Serial Driver"
  49
  50 #define USB_VENDOR_ID_QUATECH   0x061d  /* Quatech VID */
  51 #define QUATECH_SSU100  0xC020  /* SSU100 */
  52
  53 static const struct usb_device_id id_table[] = {
  54         {USB_DEVICE(USB_VENDOR_ID_QUATECH, QUATECH_SSU100)},
  55         {}                      /* Terminating entry */
  56 };
  57 MODULE_DEVICE_TABLE(usb, id_table);
  58
  59 struct ssu100_port_private {
  60         spinlock_t status_lock;
  61         u8 shadowLSR;
  62         u8 shadowMSR;
  63 };
  64
  65 static inline int ssu100_control_msg(struct usb_device *dev,
  66                                      u8 request, u16 data, u16 index)
  67 {
  68         return usb_control_msg(dev, usb_sndctrlpipe(dev, 0),
  69                                request, 0x40, data, index,
  70                                NULL, 0, 300);
  71 }
  72
  73 static inline int ssu100_setdevice(struct usb_device *dev, u8 *data)
  74 {
  75         u16 x = ((u16)(data[1] << 8) | (u16)(data[0]));
  76
  77         return ssu100_control_msg(dev, QT_SET_GET_DEVICE, x, 0);
  78 }
  79
  80
  81 static inline int ssu100_getdevice(struct usb_device *dev, u8 *data)
  82 {
  83         return usb_control_msg(dev, usb_rcvctrlpipe(dev, 0),
  84                                QT_SET_GET_DEVICE, 0xc0, 0, 0,
  85                                data, 3, 300);
  86 }
  87
  88 static inline int ssu100_getregister(struct usb_device *dev,
  89                                      unsigned short uart,
  90                                      unsigned short reg,
  91                                      u8 *data)
  92 {
  93         return usb_control_msg(dev, usb_rcvctrlpipe(dev, 0),
  94                                QT_SET_GET_REGISTER, 0xc0, reg,
  95                                uart, data, sizeof(*data), 300);
  96
  97 }
  98
  99
 100 static inline int ssu100_setregister(struct usb_device *dev,
 101                                      unsigned short uart,
 102                                      unsigned short reg,
 103                                      u16 data)
 104 {
 105         u16 value = (data << 8) | reg;
 106
 107         return usb_control_msg(dev, usb_sndctrlpipe(dev, 0),
 108                                QT_SET_GET_REGISTER, 0x40, value, uart,
 109                                NULL, 0, 300);
 110
 111 }
 112
 113 #define set_mctrl(dev, set)             update_mctrl((dev), (set), 0)
 114 #define clear_mctrl(dev, clear) update_mctrl((dev), 0, (clear))
 115
 116 /* these do not deal with device that have more than 1 port */
 117 static inline int update_mctrl(struct usb_device *dev, unsigned int set,
 118                                unsigned int clear)
 119 {
 120         unsigned urb_value;
 121         int result;
 122
 123         if (((set | clear) & (TIOCM_DTR | TIOCM_RTS)) == 0) {
 124                 dev_dbg(&dev->dev, "%s - DTR|RTS not being set|cleared\n", __func__);
 125                 return 0;       /* no change */
 126         }
 127
 128         clear &= ~set;  /* 'set' takes precedence over 'clear' */
 129         urb_value = 0;
 130         if (set & TIOCM_DTR)
 131                 urb_value |= UART_MCR_DTR;
 132         if (set & TIOCM_RTS)
 133                 urb_value |= UART_MCR_RTS;
 134
 135         result = ssu100_setregister(dev, 0, UART_MCR, urb_value);
 136         if (result < 0)
 137                 dev_dbg(&dev->dev, "%s Error from MODEM_CTRL urb\n", __func__);
 138
 139         return result;
 140 }
 141
 142 static int ssu100_initdevice(struct usb_device *dev)
 143 {
 144         u8 *data;
 145         int result = 0;
 146
 147         data = kzalloc(3, GFP_KERNEL);
 148         if (!data)
 149                 return -ENOMEM;
 150
 151         result = ssu100_getdevice(dev, data);
 152         if (result < 0) {
 153                 dev_dbg(&dev->dev, "%s - get_device failed %i\n", __func__, result);
 154                 goto out;
 155         }
 156
 157         data[1] &= ~FULLPWRBIT;
 158
 159         result = ssu100_setdevice(dev, data);
 160         if (result < 0) {
 161                 dev_dbg(&dev->dev, "%s - setdevice failed %i\n", __func__, result);
 162                 goto out;
 163         }
 164
 165         result = ssu100_control_msg(dev, QT_GET_SET_PREBUF_TRIG_LVL, 128, 0);
 166         if (result < 0) {
 167                 dev_dbg(&dev->dev, "%s - set prebuffer level failed %i\n", __func__, result);
 168                 goto out;
 169         }
 170
 171         result = ssu100_control_msg(dev, QT_SET_ATF, ATC_DISABLED, 0);
 172         if (result < 0) {
 173                 dev_dbg(&dev->dev, "%s - set ATFprebuffer level failed %i\n", __func__, result);
 174                 goto out;
 175         }
 176
 177         result = ssu100_getdevice(dev, data);
 178         if (result < 0) {
 179                 dev_dbg(&dev->dev, "%s - get_device failed %i\n", __func__, result);
 180                 goto out;
 181         }
 182
 183         data[0] &= ~(RR_BITS | DUPMODE_BITS);
 184         data[0] |= CLKS_X4;
 185         data[1] &= ~(LOOPMODE_BITS);
 186         data[1] |= RS232_MODE;
 187
 188         result = ssu100_setdevice(dev, data);
 189         if (result < 0) {
 190                 dev_dbg(&dev->dev, "%s - setdevice failed %i\n", __func__, result);
 191                 goto out;
 192         }
 193
 194 out:    kfree(data);
 195         return result;
 196
 197 }
 198
 199
 200 static void ssu100_set_termios(struct tty_struct *tty,
 201                                struct usb_serial_port *port,
 202                                struct ktermios *old_termios)
 203 {
 204         struct usb_device *dev = port->serial->dev;
 205         struct ktermios *termios = &tty->termios;
 206         u16 baud, divisor, remainder;
 207         unsigned int cflag = termios->c_cflag;
 208         u16 urb_value = 0; /* will hold the new flags */
 209         int result;
 210
 211         if (cflag & PARENB) {
 212                 if (cflag & PARODD)
 213                         urb_value |= UART_LCR_PARITY;
 214                 else
 215                         urb_value |= SERIAL_EVEN_PARITY;
 216         }
 217
 218         switch (cflag & CSIZE) {
 219         case CS5:
 220                 urb_value |= UART_LCR_WLEN5;
 221                 break;
 222         case CS6:
 223                 urb_value |= UART_LCR_WLEN6;
 224                 break;
 225         case CS7:
 226                 urb_value |= UART_LCR_WLEN7;
 227                 break;
 228         default:
 229         case CS8:
 230                 urb_value |= UART_LCR_WLEN8;
 231                 break;
 232         }
 233
 234         baud = tty_get_baud_rate(tty);
 235         if (!baud)
 236                 baud = 9600;
 237
 238         dev_dbg(&port->dev, "%s - got baud = %d\n", __func__, baud);
 239
 240
 241         divisor = MAX_BAUD_RATE / baud;
 242         remainder = MAX_BAUD_RATE % baud;
 243         if (((remainder * 2) >= baud) && (baud != 110))
 244                 divisor++;
 245
 246         urb_value = urb_value << 8;
 247
 248         result = ssu100_control_msg(dev, QT_GET_SET_UART, divisor, urb_value);
 249         if (result < 0)
 250                 dev_dbg(&port->dev, "%s - set uart failed\n", __func__);
 251
 252         if (cflag & CRTSCTS)
 253                 result = ssu100_control_msg(dev, QT_HW_FLOW_CONTROL_MASK,
 254                                             SERIAL_CRTSCTS, 0);
 255         else
 256                 result = ssu100_control_msg(dev, QT_HW_FLOW_CONTROL_MASK,
 257                                             0, 0);
 258         if (result < 0)
 259                 dev_dbg(&port->dev, "%s - set HW flow control failed\n", __func__);
 260
 261         if (I_IXOFF(tty) || I_IXON(tty)) {
 262                 u16 x = ((u16)(START_CHAR(tty) << 8) | (u16)(STOP_CHAR(tty)));
 263
 264                 result = ssu100_control_msg(dev, QT_SW_FLOW_CONTROL_MASK,
 265                                             x, 0);
 266         } else
 267                 result = ssu100_control_msg(dev, QT_SW_FLOW_CONTROL_MASK,
 268                                             0, 0);
 269
 270         if (result < 0)
 271                 dev_dbg(&port->dev, "%s - set SW flow control failed\n", __func__);
 272
 273 }
 274
 275
 276 static int ssu100_open(struct tty_struct *tty, struct usb_serial_port *port)
 277 {
 278         struct usb_device *dev = port->serial->dev;
 279         struct ssu100_port_private *priv = usb_get_serial_port_data(port);
 280         u8 *data;
 281         int result;
 282         unsigned long flags;
 283
 284         data = kzalloc(2, GFP_KERNEL);
 285         if (!data)
 286                 return -ENOMEM;
 287
 288         result = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0),
 289                                  QT_OPEN_CLOSE_CHANNEL,
 290                                  QT_TRANSFER_IN, 0x01,
 291                                  0, data, 2, 300);
 292         if (result < 0) {
 293                 dev_dbg(&port->dev, "%s - open failed %i\n", __func__, result);
 294                 kfree(data);
 295                 return result;
 296         }
 297
 298         spin_lock_irqsave(&priv->status_lock, flags);
 299         priv->shadowLSR = data[0];
 300         priv->shadowMSR = data[1];
 301         spin_unlock_irqrestore(&priv->status_lock, flags);
 302
 303         kfree(data);
 304
 305 /* set to 9600 */
 306         result = ssu100_control_msg(dev, QT_GET_SET_UART, 0x30, 0x0300);
 307         if (result < 0)
 308                 dev_dbg(&port->dev, "%s - set uart failed\n", __func__);
 309
 310         if (tty)
 311                 ssu100_set_termios(tty, port, &tty->termios);
 312
 313         return usb_serial_generic_open(tty, port);
 314 }
 315
 316 static int get_serial_info(struct usb_serial_port *port,
 317                            struct serial_struct __user *retinfo)
 318 {
 319         struct serial_struct tmp;
 320
 321         memset(&tmp, 0, sizeof(tmp));
 322         tmp.line                = port->minor;
 323         tmp.port                = 0;
 324         tmp.irq                 = 0;
 325         tmp.flags               = ASYNC_SKIP_TEST | ASYNC_AUTO_IRQ;
 326         tmp.xmit_fifo_size      = port->bulk_out_size;
 327         tmp.baud_base           = 9600;
 328         tmp.close_delay         = 5*HZ;
 329         tmp.closing_wait        = 30*HZ;
 330
 331         if (copy_to_user(retinfo, &tmp, sizeof(*retinfo)))
 332                 return -EFAULT;
 333         return 0;
 334 }
 335
 336 static int ssu100_ioctl(struct tty_struct *tty,
 337                     unsigned int cmd, unsigned long arg)
 338 {
 339         struct usb_serial_port *port = tty->driver_data;
 340
 341         switch (cmd) {
 342         case TIOCGSERIAL:
 343                 return get_serial_info(port,
 344                                        (struct serial_struct __user *) arg);
 345         default:
 346                 break;
 347         }
 348
 349         return -ENOIOCTLCMD;
 350 }
 351
 352 static int ssu100_attach(struct usb_serial *serial)
 353 {
 354         return ssu100_initdevice(serial->dev);
 355 }
 356
 357 static int ssu100_port_probe(struct usb_serial_port *port)
 358 {
 359         struct ssu100_port_private *priv;
 360
 361         priv = kzalloc(sizeof(*priv), GFP_KERNEL);
 362         if (!priv)
 363                 return -ENOMEM;
 364
 365         spin_lock_init(&priv->status_lock);
 366
 367         usb_set_serial_port_data(port, priv);
 368
 369         return 0;
 370 }
 371
 372 static int ssu100_port_remove(struct usb_serial_port *port)
 373 {
 374         struct ssu100_port_private *priv;
 375
 376         priv = usb_get_serial_port_data(port);
 377         kfree(priv);
 378
 379         return 0;
 380 }
 381
 382 static int ssu100_tiocmget(struct tty_struct *tty)
 383 {
 384         struct usb_serial_port *port = tty->driver_data;
 385         struct usb_device *dev = port->serial->dev;
 386         u8 *d;
 387         int r;
 388
 389         d = kzalloc(2, GFP_KERNEL);
 390         if (!d)
 391                 return -ENOMEM;
 392
 393         r = ssu100_getregister(dev, 0, UART_MCR, d);
 394         if (r < 0)
 395                 goto mget_out;
 396
 397         r = ssu100_getregister(dev, 0, UART_MSR, d+1);
 398         if (r < 0)
 399                 goto mget_out;
 400
 401         r = (d[0] & UART_MCR_DTR ? TIOCM_DTR : 0) |
 402                 (d[0] & UART_MCR_RTS ? TIOCM_RTS : 0) |
 403                 (d[1] & UART_MSR_CTS ? TIOCM_CTS : 0) |
 404                 (d[1] & UART_MSR_DCD ? TIOCM_CAR : 0) |
 405                 (d[1] & UART_MSR_RI ? TIOCM_RI : 0) |
 406                 (d[1] & UART_MSR_DSR ? TIOCM_DSR : 0);
 407
 408 mget_out:
 409         kfree(d);
 410         return r;
 411 }
 412
 413 static int ssu100_tiocmset(struct tty_struct *tty,
 414                            unsigned int set, unsigned int clear)
 415 {
 416         struct usb_serial_port *port = tty->driver_data;
 417         struct usb_device *dev = port->serial->dev;
 418
 419         return update_mctrl(dev, set, clear);
 420 }
 421
 422 static void ssu100_dtr_rts(struct usb_serial_port *port, int on)
 423 {
 424         struct usb_device *dev = port->serial->dev;
 425
 426         /* Disable flow control */
 427         if (!on) {
 428                 if (ssu100_setregister(dev, 0, UART_MCR, 0) < 0)
 429                         dev_err(&port->dev, "error from flowcontrol urb\n");
 430         }
 431         /* drop RTS and DTR */
 432         if (on)
 433                 set_mctrl(dev, TIOCM_DTR | TIOCM_RTS);
 434         else
 435                 clear_mctrl(dev, TIOCM_DTR | TIOCM_RTS);
 436 }
 437
 438 static void ssu100_update_msr(struct usb_serial_port *port, u8 msr)
 439 {
 440         struct ssu100_port_private *priv = usb_get_serial_port_data(port);
 441         unsigned long flags;
 442
 443         spin_lock_irqsave(&priv->status_lock, flags);
 444         priv->shadowMSR = msr;
 445         spin_unlock_irqrestore(&priv->status_lock, flags);
 446
 447         if (msr & UART_MSR_ANY_DELTA) {
 448                 /* update input line counters */
 449                 if (msr & UART_MSR_DCTS)
 450                         port->icount.cts++;
 451                 if (msr & UART_MSR_DDSR)
 452                         port->icount.dsr++;
 453                 if (msr & UART_MSR_DDCD)
 454                         port->icount.dcd++;
 455                 if (msr & UART_MSR_TERI)
 456                         port->icount.rng++;
 457                 wake_up_interruptible(&port->port.delta_msr_wait);
 458         }
 459 }
 460
 461 static void ssu100_update_lsr(struct usb_serial_port *port, u8 lsr,
 462                               char *tty_flag)
 463 {
 464         struct ssu100_port_private *priv = usb_get_serial_port_data(port);
 465         unsigned long flags;
 466
 467         spin_lock_irqsave(&priv->status_lock, flags);
 468         priv->shadowLSR = lsr;
 469         spin_unlock_irqrestore(&priv->status_lock, flags);
 470
 471         *tty_flag = TTY_NORMAL;
 472         if (lsr & UART_LSR_BRK_ERROR_BITS) {
 473                 /* we always want to update icount, but we only want to
 474                  * update tty_flag for one case */
 475                 if (lsr & UART_LSR_BI) {
 476                         port->icount.brk++;
 477                         *tty_flag = TTY_BREAK;
 478                         usb_serial_handle_break(port);
 479                 }
 480                 if (lsr & UART_LSR_PE) {
 481                         port->icount.parity++;
 482                         if (*tty_flag == TTY_NORMAL)
 483                                 *tty_flag = TTY_PARITY;
 484                 }
 485                 if (lsr & UART_LSR_FE) {
 486                         port->icount.frame++;
 487                         if (*tty_flag == TTY_NORMAL)
 488                                 *tty_flag = TTY_FRAME;
 489                 }
 490                 if (lsr & UART_LSR_OE) {
 491                         port->icount.overrun++;
 492                         tty_insert_flip_char(&port->port, 0, TTY_OVERRUN);
 493                 }
 494         }
 495
 496 }
 497
 498 static void ssu100_process_read_urb(struct urb *urb)
 499 {
 500         struct usb_serial_port *port = urb->context;
 501         char *packet = (char *)urb->transfer_buffer;
 502         char flag = TTY_NORMAL;
 503         u32 len = urb->actual_length;
 504         int i;
 505         char *ch;
 506
 507         if ((len >= 4) &&
 508             (packet[0] == 0x1b) && (packet[1] == 0x1b) &&
 509             ((packet[2] == 0x00) || (packet[2] == 0x01))) {
 510                 if (packet[2] == 0x00)
 511                         ssu100_update_lsr(port, packet[3], &flag);
 512                 if (packet[2] == 0x01)
 513                         ssu100_update_msr(port, packet[3]);
 514
 515                 len -= 4;
 516                 ch = packet + 4;
 517         } else
 518                 ch = packet;
 519
 520         if (!len)
 521                 return; /* status only */
 522
 523         if (port->port.console && port->sysrq) {
 524                 for (i = 0; i < len; i++, ch++) {
 525                         if (!usb_serial_handle_sysrq_char(port, *ch))
 526                                 tty_insert_flip_char(&port->port, *ch, flag);
 527                 }
 528         } else
 529                 tty_insert_flip_string_fixed_flag(&port->port, ch, flag, len);
 530
 531         tty_flip_buffer_push(&port->port);
 532 }
 533
 534 static struct usb_serial_driver ssu100_device = {
 535         .driver = {
 536                 .owner = THIS_MODULE,
 537                 .name = "ssu100",
 538         },
 539         .description         = DRIVER_DESC,
 540         .id_table            = id_table,
 541         .num_ports           = 1,
 542         .open                = ssu100_open,
 543         .attach              = ssu100_attach,
 544         .port_probe          = ssu100_port_probe,
 545         .port_remove         = ssu100_port_remove,
 546         .dtr_rts             = ssu100_dtr_rts,
 547         .process_read_urb    = ssu100_process_read_urb,
 548         .tiocmget            = ssu100_tiocmget,
 549         .tiocmset            = ssu100_tiocmset,
 550         .tiocmiwait          = usb_serial_generic_tiocmiwait,
 551         .get_icount          = usb_serial_generic_get_icount,
 552         .ioctl               = ssu100_ioctl,
 553         .set_termios         = ssu100_set_termios,
 554 };
 555
 556 static struct usb_serial_driver * const serial_drivers[] = {
 557         &ssu100_device, NULL
 558 };
 559
 560 module_usb_serial_driver(serial_drivers, id_table);
 561
 562 MODULE_DESCRIPTION(DRIVER_DESC);
 563 MODULE_LICENSE("GPL");