Merge drm-misc-next-fixes-2024-01-19 into drm-misc-fixes

[linux.git] / include / linux / spi / spi.h

/* SPDX-License-Identifier: GPL-2.0-or-later
 *
 * Copyright (C) 2005 David Brownell
 */

#ifndef __LINUX_SPI_H
#define __LINUX_SPI_H

#include <linux/acpi.h>
#include <linux/bits.h>
#include <linux/completion.h>
#include <linux/device.h>
#include <linux/gpio/consumer.h>
#include <linux/kthread.h>
#include <linux/mod_devicetable.h>
#include <linux/overflow.h>
#include <linux/scatterlist.h>
#include <linux/slab.h>
#include <linux/u64_stats_sync.h>

#include <uapi/linux/spi/spi.h>

/* Max no. of CS supported per spi device */
#define SPI_CS_CNT_MAX 4

struct dma_chan;
struct software_node;
struct ptp_system_timestamp;
struct spi_controller;
struct spi_transfer;
struct spi_controller_mem_ops;
struct spi_controller_mem_caps;
struct spi_message;

/*
 * INTERFACES between SPI master-side drivers and SPI slave protocol handlers,
 * and SPI infrastructure.
 */
extern struct bus_type spi_bus_type;

/**
 * struct spi_statistics - statistics for spi transfers
 * @syncp:         seqcount to protect members in this struct for per-cpu update
 *                 on 32-bit systems
 *
 * @messages:      number of spi-messages handled
 * @transfers:     number of spi_transfers handled
 * @errors:        number of errors during spi_transfer
 * @timedout:      number of timeouts during spi_transfer
 *
 * @spi_sync:      number of times spi_sync is used
 * @spi_sync_immediate:
 *                 number of times spi_sync is executed immediately
 *                 in calling context without queuing and scheduling
 * @spi_async:     number of times spi_async is used
 *
 * @bytes:         number of bytes transferred to/from device
 * @bytes_tx:      number of bytes sent to device
 * @bytes_rx:      number of bytes received from device
 *
 * @transfer_bytes_histo:
 *                 transfer bytes histogram
 *
 * @transfers_split_maxsize:
 *                 number of transfers that have been split because of
 *                 maxsize limit
 */
struct spi_statistics {
        struct u64_stats_sync   syncp;

        u64_stats_t             messages;
        u64_stats_t             transfers;
        u64_stats_t             errors;
        u64_stats_t             timedout;

        u64_stats_t             spi_sync;
        u64_stats_t             spi_sync_immediate;
        u64_stats_t             spi_async;

        u64_stats_t             bytes;
        u64_stats_t             bytes_rx;
        u64_stats_t             bytes_tx;

#define SPI_STATISTICS_HISTO_SIZE 17
        u64_stats_t     transfer_bytes_histo[SPI_STATISTICS_HISTO_SIZE];

        u64_stats_t     transfers_split_maxsize;
};

#define SPI_STATISTICS_ADD_TO_FIELD(pcpu_stats, field, count)           \
        do {                                                            \
                struct spi_statistics *__lstats;                        \
                get_cpu();                                              \
                __lstats = this_cpu_ptr(pcpu_stats);                    \
                u64_stats_update_begin(&__lstats->syncp);               \
                u64_stats_add(&__lstats->field, count);                 \
                u64_stats_update_end(&__lstats->syncp);                 \
                put_cpu();                                              \
        } while (0)

#define SPI_STATISTICS_INCREMENT_FIELD(pcpu_stats, field)               \
        do {                                                            \
                struct spi_statistics *__lstats;                        \
                get_cpu();                                              \
                __lstats = this_cpu_ptr(pcpu_stats);                    \
                u64_stats_update_begin(&__lstats->syncp);               \
                u64_stats_inc(&__lstats->field);                        \
                u64_stats_update_end(&__lstats->syncp);                 \
                put_cpu();                                              \
        } while (0)

/**
 * struct spi_delay - SPI delay information
 * @value: Value for the delay
 * @unit: Unit for the delay
 */
struct spi_delay {
#define SPI_DELAY_UNIT_USECS    0
#define SPI_DELAY_UNIT_NSECS    1
#define SPI_DELAY_UNIT_SCK      2
        u16     value;
        u8      unit;
};

extern int spi_delay_to_ns(struct spi_delay *_delay, struct spi_transfer *xfer);
extern int spi_delay_exec(struct spi_delay *_delay, struct spi_transfer *xfer);
extern void spi_transfer_cs_change_delay_exec(struct spi_message *msg,
                                                  struct spi_transfer *xfer);

/**
 * struct spi_device - Controller side proxy for an SPI slave device
 * @dev: Driver model representation of the device.
 * @controller: SPI controller used with the device.
 * @master: Copy of controller, for backwards compatibility.
 * @max_speed_hz: Maximum clock rate to be used with this chip
 *      (on this board); may be changed by the device's driver.
 *      The spi_transfer.speed_hz can override this for each transfer.
 * @chip_select: Array of physical chipselect, spi->chipselect[i] gives
 *      the corresponding physical CS for logical CS i.
 * @mode: The spi mode defines how data is clocked out and in.
 *      This may be changed by the device's driver.
 *      The "active low" default for chipselect mode can be overridden
 *      (by specifying SPI_CS_HIGH) as can the "MSB first" default for
 *      each word in a transfer (by specifying SPI_LSB_FIRST).
 * @bits_per_word: Data transfers involve one or more words; word sizes
 *      like eight or 12 bits are common.  In-memory wordsizes are
 *      powers of two bytes (e.g. 20 bit samples use 32 bits).
 *      This may be changed by the device's driver, or left at the
 *      default (0) indicating protocol words are eight bit bytes.
 *      The spi_transfer.bits_per_word can override this for each transfer.
 * @rt: Make the pump thread real time priority.
 * @irq: Negative, or the number passed to request_irq() to receive
 *      interrupts from this device.
 * @controller_state: Controller's runtime state
 * @controller_data: Board-specific definitions for controller, such as
 *      FIFO initialization parameters; from board_info.controller_data
 * @modalias: Name of the driver to use with this device, or an alias
 *      for that name.  This appears in the sysfs "modalias" attribute
 *      for driver coldplugging, and in uevents used for hotplugging
 * @driver_override: If the name of a driver is written to this attribute, then
 *      the device will bind to the named driver and only the named driver.
 *      Do not set directly, because core frees it; use driver_set_override() to
 *      set or clear it.
 * @cs_gpiod: Array of GPIO descriptors of the corresponding chipselect lines
 *      (optional, NULL when not using a GPIO line)
 * @word_delay: delay to be inserted between consecutive
 *      words of a transfer
 * @cs_setup: delay to be introduced by the controller after CS is asserted
 * @cs_hold: delay to be introduced by the controller before CS is deasserted
 * @cs_inactive: delay to be introduced by the controller after CS is
 *      deasserted. If @cs_change_delay is used from @spi_transfer, then the
 *      two delays will be added up.
 * @pcpu_statistics: statistics for the spi_device
 * @cs_index_mask: Bit mask of the active chipselect(s) in the chipselect array
 *
 * A @spi_device is used to interchange data between an SPI slave
 * (usually a discrete chip) and CPU memory.
 *
 * In @dev, the platform_data is used to hold information about this
 * device that's meaningful to the device's protocol driver, but not
 * to its controller.  One example might be an identifier for a chip
 * variant with slightly different functionality; another might be
 * information about how this particular board wires the chip's pins.
 */
struct spi_device {
        struct device           dev;
        struct spi_controller   *controller;
        struct spi_controller   *master;        /* Compatibility layer */
        u32                     max_speed_hz;
        u8                      chip_select[SPI_CS_CNT_MAX];
        u8                      bits_per_word;
        bool                    rt;
#define SPI_NO_TX               BIT(31)         /* No transmit wire */
#define SPI_NO_RX               BIT(30)         /* No receive wire */
        /*
         * TPM specification defines flow control over SPI. Client device
         * can insert a wait state on MISO when address is transmitted by
         * controller on MOSI. Detecting the wait state in software is only
         * possible for full duplex controllers. For controllers that support
         * only half-duplex, the wait state detection needs to be implemented
         * in hardware. TPM devices would set this flag when hardware flow
         * control is expected from SPI controller.
         */
#define SPI_TPM_HW_FLOW         BIT(29)         /* TPM HW flow control */
        /*
         * All bits defined above should be covered by SPI_MODE_KERNEL_MASK.
         * The SPI_MODE_KERNEL_MASK has the SPI_MODE_USER_MASK counterpart,
         * which is defined in 'include/uapi/linux/spi/spi.h'.
         * The bits defined here are from bit 31 downwards, while in
         * SPI_MODE_USER_MASK are from 0 upwards.
         * These bits must not overlap. A static assert check should make sure of that.
         * If adding extra bits, make sure to decrease the bit index below as well.
         */
#define SPI_MODE_KERNEL_MASK    (~(BIT(29) - 1))
        u32                     mode;
        int                     irq;
        void                    *controller_state;
        void                    *controller_data;
        char                    modalias[SPI_NAME_SIZE];
        const char              *driver_override;
        struct gpio_desc        *cs_gpiod[SPI_CS_CNT_MAX];      /* Chip select gpio desc */
        struct spi_delay        word_delay; /* Inter-word delay */
        /* CS delays */
        struct spi_delay        cs_setup;
        struct spi_delay        cs_hold;
        struct spi_delay        cs_inactive;

        /* The statistics */
        struct spi_statistics __percpu  *pcpu_statistics;

        /* Bit mask of the chipselect(s) that the driver need to use from
         * the chipselect array.When the controller is capable to handle
         * multiple chip selects & memories are connected in parallel
         * then more than one bit need to be set in cs_index_mask.
         */
        u32                     cs_index_mask : SPI_CS_CNT_MAX;

        /*
         * Likely need more hooks for more protocol options affecting how
         * the controller talks to each chip, like:
         *  - memory packing (12 bit samples into low bits, others zeroed)
         *  - priority
         *  - chipselect delays
         *  - ...
         */
};

/* Make sure that SPI_MODE_KERNEL_MASK & SPI_MODE_USER_MASK don't overlap */
static_assert((SPI_MODE_KERNEL_MASK & SPI_MODE_USER_MASK) == 0,
              "SPI_MODE_USER_MASK & SPI_MODE_KERNEL_MASK must not overlap");

static inline struct spi_device *to_spi_device(const struct device *dev)
{
        return dev ? container_of(dev, struct spi_device, dev) : NULL;
}

/* Most drivers won't need to care about device refcounting */
static inline struct spi_device *spi_dev_get(struct spi_device *spi)
{
        return (spi && get_device(&spi->dev)) ? spi : NULL;
}

static inline void spi_dev_put(struct spi_device *spi)
{
        if (spi)
                put_device(&spi->dev);
}

/* ctldata is for the bus_controller driver's runtime state */
static inline void *spi_get_ctldata(const struct spi_device *spi)
{
        return spi->controller_state;
}

static inline void spi_set_ctldata(struct spi_device *spi, void *state)
{
        spi->controller_state = state;
}

/* Device driver data */

static inline void spi_set_drvdata(struct spi_device *spi, void *data)
{
        dev_set_drvdata(&spi->dev, data);
}

static inline void *spi_get_drvdata(const struct spi_device *spi)
{
        return dev_get_drvdata(&spi->dev);
}

static inline u8 spi_get_chipselect(const struct spi_device *spi, u8 idx)
{
        return spi->chip_select[idx];
}

static inline void spi_set_chipselect(struct spi_device *spi, u8 idx, u8 chipselect)
{
        spi->chip_select[idx] = chipselect;
}

static inline struct gpio_desc *spi_get_csgpiod(const struct spi_device *spi, u8 idx)
{
        return spi->cs_gpiod[idx];
}

static inline void spi_set_csgpiod(struct spi_device *spi, u8 idx, struct gpio_desc *csgpiod)
{
        spi->cs_gpiod[idx] = csgpiod;
}

static inline bool spi_is_csgpiod(struct spi_device *spi)
{
        u8 idx;

        for (idx = 0; idx < SPI_CS_CNT_MAX; idx++) {
                if (spi_get_csgpiod(spi, idx))
                        return true;
        }
        return false;
}

/**
 * struct spi_driver - Host side "protocol" driver
 * @id_table: List of SPI devices supported by this driver
 * @probe: Binds this driver to the SPI device.  Drivers can verify
 *      that the device is actually present, and may need to configure
 *      characteristics (such as bits_per_word) which weren't needed for
 *      the initial configuration done during system setup.
 * @remove: Unbinds this driver from the SPI device
 * @shutdown: Standard shutdown callback used during system state
 *      transitions such as powerdown/halt and kexec
 * @driver: SPI device drivers should initialize the name and owner
 *      field of this structure.
 *
 * This represents the kind of device driver that uses SPI messages to
 * interact with the hardware at the other end of a SPI link.  It's called
 * a "protocol" driver because it works through messages rather than talking
 * directly to SPI hardware (which is what the underlying SPI controller
 * driver does to pass those messages).  These protocols are defined in the
 * specification for the device(s) supported by the driver.
 *
 * As a rule, those device protocols represent the lowest level interface
 * supported by a driver, and it will support upper level interfaces too.
 * Examples of such upper levels include frameworks like MTD, networking,
 * MMC, RTC, filesystem character device nodes, and hardware monitoring.
 */
struct spi_driver {
        const struct spi_device_id *id_table;
        int                     (*probe)(struct spi_device *spi);
        void                    (*remove)(struct spi_device *spi);
        void                    (*shutdown)(struct spi_device *spi);
        struct device_driver    driver;
};

static inline struct spi_driver *to_spi_driver(struct device_driver *drv)
{
        return drv ? container_of(drv, struct spi_driver, driver) : NULL;
}

extern int __spi_register_driver(struct module *owner, struct spi_driver *sdrv);

/**
 * spi_unregister_driver - reverse effect of spi_register_driver
 * @sdrv: the driver to unregister
 * Context: can sleep
 */
static inline void spi_unregister_driver(struct spi_driver *sdrv)
{
        if (sdrv)
                driver_unregister(&sdrv->driver);
}

extern struct spi_device *spi_new_ancillary_device(struct spi_device *spi, u8 chip_select);

/* Use a define to avoid include chaining to get THIS_MODULE */
#define spi_register_driver(driver) \
        __spi_register_driver(THIS_MODULE, driver)

/**
 * module_spi_driver() - Helper macro for registering a SPI driver
 * @__spi_driver: spi_driver struct
 *
 * Helper macro for SPI drivers which do not do anything special in module
 * init/exit. This eliminates a lot of boilerplate. Each module may only
 * use this macro once, and calling it replaces module_init() and module_exit()
 */
#define module_spi_driver(__spi_driver) \
        module_driver(__spi_driver, spi_register_driver, \
                        spi_unregister_driver)

/**
 * struct spi_controller - interface to SPI master or slave controller
 * @dev: device interface to this driver
 * @list: link with the global spi_controller list
 * @bus_num: board-specific (and often SOC-specific) identifier for a
 *      given SPI controller.
 * @num_chipselect: chipselects are used to distinguish individual
 *      SPI slaves, and are numbered from zero to num_chipselects.
 *      each slave has a chipselect signal, but it's common that not
 *      every chipselect is connected to a slave.
 * @dma_alignment: SPI controller constraint on DMA buffers alignment.
 * @mode_bits: flags understood by this controller driver
 * @buswidth_override_bits: flags to override for this controller driver
 * @bits_per_word_mask: A mask indicating which values of bits_per_word are
 *      supported by the driver. Bit n indicates that a bits_per_word n+1 is
 *      supported. If set, the SPI core will reject any transfer with an
 *      unsupported bits_per_word. If not set, this value is simply ignored,
 *      and it's up to the individual driver to perform any validation.
 * @min_speed_hz: Lowest supported transfer speed
 * @max_speed_hz: Highest supported transfer speed
 * @flags: other constraints relevant to this driver
 * @slave: indicates that this is an SPI slave controller
 * @target: indicates that this is an SPI target controller
 * @devm_allocated: whether the allocation of this struct is devres-managed
 * @max_transfer_size: function that returns the max transfer size for
 *      a &spi_device; may be %NULL, so the default %SIZE_MAX will be used.
 * @max_message_size: function that returns the max message size for
 *      a &spi_device; may be %NULL, so the default %SIZE_MAX will be used.
 * @io_mutex: mutex for physical bus access
 * @add_lock: mutex to avoid adding devices to the same chipselect
 * @bus_lock_spinlock: spinlock for SPI bus locking
 * @bus_lock_mutex: mutex for exclusion of multiple callers
 * @bus_lock_flag: indicates that the SPI bus is locked for exclusive use
 * @multi_cs_cap: indicates that the SPI Controller can assert/de-assert
 *      more than one chip select at once.
 * @setup: updates the device mode and clocking records used by a
 *      device's SPI controller; protocol code may call this.  This
 *      must fail if an unrecognized or unsupported mode is requested.
 *      It's always safe to call this unless transfers are pending on
 *      the device whose settings are being modified.
 * @set_cs_timing: optional hook for SPI devices to request SPI master
 * controller for configuring specific CS setup time, hold time and inactive
 * delay interms of clock counts
 * @transfer: adds a message to the controller's transfer queue.
 * @cleanup: frees controller-specific state
 * @can_dma: determine whether this controller supports DMA
 * @dma_map_dev: device which can be used for DMA mapping
 * @cur_rx_dma_dev: device which is currently used for RX DMA mapping
 * @cur_tx_dma_dev: device which is currently used for TX DMA mapping
 * @queued: whether this controller is providing an internal message queue
 * @kworker: pointer to thread struct for message pump
 * @pump_messages: work struct for scheduling work to the message pump
 * @queue_lock: spinlock to synchronise access to message queue
 * @queue: message queue
 * @cur_msg: the currently in-flight message
 * @cur_msg_completion: a completion for the current in-flight message
 * @cur_msg_incomplete: Flag used internally to opportunistically skip
 *      the @cur_msg_completion. This flag is used to check if the driver has
 *      already called spi_finalize_current_message().
 * @cur_msg_need_completion: Flag used internally to opportunistically skip
 *      the @cur_msg_completion. This flag is used to signal the context that
 *      is running spi_finalize_current_message() that it needs to complete()
 * @cur_msg_mapped: message has been mapped for DMA
 * @last_cs: the last chip_select that is recorded by set_cs, -1 on non chip
 *           selected
 * @last_cs_mode_high: was (mode & SPI_CS_HIGH) true on the last call to set_cs.
 * @xfer_completion: used by core transfer_one_message()
 * @busy: message pump is busy
 * @running: message pump is running
 * @rt: whether this queue is set to run as a realtime task
 * @auto_runtime_pm: the core should ensure a runtime PM reference is held
 *                   while the hardware is prepared, using the parent
 *                   device for the spidev
 * @max_dma_len: Maximum length of a DMA transfer for the device.
 * @prepare_transfer_hardware: a message will soon arrive from the queue
 *      so the subsystem requests the driver to prepare the transfer hardware
 *      by issuing this call
 * @transfer_one_message: the subsystem calls the driver to transfer a single
 *      message while queuing transfers that arrive in the meantime. When the
 *      driver is finished with this message, it must call
 *      spi_finalize_current_message() so the subsystem can issue the next
 *      message
 * @unprepare_transfer_hardware: there are currently no more messages on the
 *      queue so the subsystem notifies the driver that it may relax the
 *      hardware by issuing this call
 *
 * @set_cs: set the logic level of the chip select line.  May be called
 *          from interrupt context.
 * @prepare_message: set up the controller to transfer a single message,
 *                   for example doing DMA mapping.  Called from threaded
 *                   context.
 * @transfer_one: transfer a single spi_transfer.
 *
 *                  - return 0 if the transfer is finished,
 *                  - return 1 if the transfer is still in progress. When
 *                    the driver is finished with this transfer it must
 *                    call spi_finalize_current_transfer() so the subsystem
 *                    can issue the next transfer. If the transfer fails, the
 *                    driver must set the flag SPI_TRANS_FAIL_IO to
 *                    spi_transfer->error first, before calling
 *                    spi_finalize_current_transfer().
 *                    Note: transfer_one and transfer_one_message are mutually
 *                    exclusive; when both are set, the generic subsystem does
 *                    not call your transfer_one callback.
 * @handle_err: the subsystem calls the driver to handle an error that occurs
 *              in the generic implementation of transfer_one_message().
 * @mem_ops: optimized/dedicated operations for interactions with SPI memory.
 *           This field is optional and should only be implemented if the
 *           controller has native support for memory like operations.
 * @mem_caps: controller capabilities for the handling of memory operations.
 * @unprepare_message: undo any work done by prepare_message().
 * @slave_abort: abort the ongoing transfer request on an SPI slave controller
 * @target_abort: abort the ongoing transfer request on an SPI target controller
 * @cs_gpiods: Array of GPIO descriptors to use as chip select lines; one per CS
 *      number. Any individual value may be NULL for CS lines that
 *      are not GPIOs (driven by the SPI controller itself).
 * @use_gpio_descriptors: Turns on the code in the SPI core to parse and grab
 *      GPIO descriptors. This will fill in @cs_gpiods and SPI devices will have
 *      the cs_gpiod assigned if a GPIO line is found for the chipselect.
 * @unused_native_cs: When cs_gpiods is used, spi_register_controller() will
 *      fill in this field with the first unused native CS, to be used by SPI
 *      controller drivers that need to drive a native CS when using GPIO CS.
 * @max_native_cs: When cs_gpiods is used, and this field is filled in,
 *      spi_register_controller() will validate all native CS (including the
 *      unused native CS) against this value.
 * @pcpu_statistics: statistics for the spi_controller
 * @dma_tx: DMA transmit channel
 * @dma_rx: DMA receive channel
 * @dummy_rx: dummy receive buffer for full-duplex devices
 * @dummy_tx: dummy transmit buffer for full-duplex devices
 * @fw_translate_cs: If the boot firmware uses different numbering scheme
 *      what Linux expects, this optional hook can be used to translate
 *      between the two.
 * @ptp_sts_supported: If the driver sets this to true, it must provide a
 *      time snapshot in @spi_transfer->ptp_sts as close as possible to the
 *      moment in time when @spi_transfer->ptp_sts_word_pre and
 *      @spi_transfer->ptp_sts_word_post were transmitted.
 *      If the driver does not set this, the SPI core takes the snapshot as
 *      close to the driver hand-over as possible.
 * @irq_flags: Interrupt enable state during PTP system timestamping
 * @fallback: fallback to PIO if DMA transfer return failure with
 *      SPI_TRANS_FAIL_NO_START.
 * @queue_empty: signal green light for opportunistically skipping the queue
 *      for spi_sync transfers.
 * @must_async: disable all fast paths in the core
 *
 * Each SPI controller can communicate with one or more @spi_device
 * children.  These make a small bus, sharing MOSI, MISO and SCK signals
 * but not chip select signals.  Each device may be configured to use a
 * different clock rate, since those shared signals are ignored unless
 * the chip is selected.
 *
 * The driver for an SPI controller manages access to those devices through
 * a queue of spi_message transactions, copying data between CPU memory and
 * an SPI slave device.  For each such message it queues, it calls the
 * message's completion function when the transaction completes.
 */
struct spi_controller {
        struct device   dev;

        struct list_head list;

        /*
         * Other than negative (== assign one dynamically), bus_num is fully
         * board-specific. Usually that simplifies to being SoC-specific.
         * example: one SoC has three SPI controllers, numbered 0..2,
         * and one board's schematics might show it using SPI-2. Software
         * would normally use bus_num=2 for that controller.
         */
        s16                     bus_num;

        /*
         * Chipselects will be integral to many controllers; some others
         * might use board-specific GPIOs.
         */
        u16                     num_chipselect;

        /* Some SPI controllers pose alignment requirements on DMAable
         * buffers; let protocol drivers know about these requirements.
         */
        u16                     dma_alignment;

        /* spi_device.mode flags understood by this controller driver */
        u32                     mode_bits;

        /* spi_device.mode flags override flags for this controller */
        u32                     buswidth_override_bits;

        /* Bitmask of supported bits_per_word for transfers */
        u32                     bits_per_word_mask;
#define SPI_BPW_MASK(bits) BIT((bits) - 1)
#define SPI_BPW_RANGE_MASK(min, max) GENMASK((max) - 1, (min) - 1)

        /* Limits on transfer speed */
        u32                     min_speed_hz;
        u32                     max_speed_hz;

        /* Other constraints relevant to this driver */
        u16                     flags;
#define SPI_CONTROLLER_HALF_DUPLEX      BIT(0)  /* Can't do full duplex */
#define SPI_CONTROLLER_NO_RX            BIT(1)  /* Can't do buffer read */
#define SPI_CONTROLLER_NO_TX            BIT(2)  /* Can't do buffer write */
#define SPI_CONTROLLER_MUST_RX          BIT(3)  /* Requires rx */
#define SPI_CONTROLLER_MUST_TX          BIT(4)  /* Requires tx */
#define SPI_CONTROLLER_GPIO_SS          BIT(5)  /* GPIO CS must select slave */
#define SPI_CONTROLLER_SUSPENDED        BIT(6)  /* Currently suspended */
        /*
         * The spi-controller has multi chip select capability and can
         * assert/de-assert more than one chip select at once.
         */
#define SPI_CONTROLLER_MULTI_CS         BIT(7)

        /* Flag indicating if the allocation of this struct is devres-managed */
        bool                    devm_allocated;

        union {
                /* Flag indicating this is an SPI slave controller */
                bool                    slave;
                /* Flag indicating this is an SPI target controller */
                bool                    target;
        };

        /*
         * On some hardware transfer / message size may be constrained
         * the limit may depend on device transfer settings.
         */
        size_t (*max_transfer_size)(struct spi_device *spi);
        size_t (*max_message_size)(struct spi_device *spi);

        /* I/O mutex */
        struct mutex            io_mutex;

        /* Used to avoid adding the same CS twice */
        struct mutex            add_lock;

        /* Lock and mutex for SPI bus locking */
        spinlock_t              bus_lock_spinlock;
        struct mutex            bus_lock_mutex;

        /* Flag indicating that the SPI bus is locked for exclusive use */
        bool                    bus_lock_flag;

        /*
         * Setup mode and clock, etc (SPI driver may call many times).
         *
         * IMPORTANT:  this may be called when transfers to another
         * device are active.  DO NOT UPDATE SHARED REGISTERS in ways
         * which could break those transfers.
         */
        int                     (*setup)(struct spi_device *spi);

        /*
         * set_cs_timing() method is for SPI controllers that supports
         * configuring CS timing.
         *
         * This hook allows SPI client drivers to request SPI controllers
         * to configure specific CS timing through spi_set_cs_timing() after
         * spi_setup().
         */
        int (*set_cs_timing)(struct spi_device *spi);

        /*
         * Bidirectional bulk transfers
         *
         * + The transfer() method may not sleep; its main role is
         *   just to add the message to the queue.
         * + For now there's no remove-from-queue operation, or
         *   any other request management
         * + To a given spi_device, message queueing is pure FIFO
         *
         * + The controller's main job is to process its message queue,
         *   selecting a chip (for masters), then transferring data
         * + If there are multiple spi_device children, the i/o queue
         *   arbitration algorithm is unspecified (round robin, FIFO,
         *   priority, reservations, preemption, etc)
         *
         * + Chipselect stays active during the entire message
         *   (unless modified by spi_transfer.cs_change != 0).
         * + The message transfers use clock and SPI mode parameters
         *   previously established by setup() for this device
         */
        int                     (*transfer)(struct spi_device *spi,
                                                struct spi_message *mesg);

        /* Called on release() to free memory provided by spi_controller */
        void                    (*cleanup)(struct spi_device *spi);

        /*
         * Used to enable core support for DMA handling, if can_dma()
         * exists and returns true then the transfer will be mapped
         * prior to transfer_one() being called.  The driver should
         * not modify or store xfer and dma_tx and dma_rx must be set
         * while the device is prepared.
         */
        bool                    (*can_dma)(struct spi_controller *ctlr,
                                           struct spi_device *spi,
                                           struct spi_transfer *xfer);
        struct device *dma_map_dev;
        struct device *cur_rx_dma_dev;
        struct device *cur_tx_dma_dev;

        /*
         * These hooks are for drivers that want to use the generic
         * controller transfer queueing mechanism. If these are used, the
         * transfer() function above must NOT be specified by the driver.
         * Over time we expect SPI drivers to be phased over to this API.
         */
        bool                            queued;
        struct kthread_worker           *kworker;
        struct kthread_work             pump_messages;
        spinlock_t                      queue_lock;
        struct list_head                queue;
        struct spi_message              *cur_msg;
        struct completion               cur_msg_completion;
        bool                            cur_msg_incomplete;
        bool                            cur_msg_need_completion;
        bool                            busy;
        bool                            running;
        bool                            rt;
        bool                            auto_runtime_pm;
        bool                            cur_msg_mapped;
        char                            last_cs[SPI_CS_CNT_MAX];
        char                            last_cs_index_mask;
        bool                            last_cs_mode_high;
        bool                            fallback;
        struct completion               xfer_completion;
        size_t                          max_dma_len;

        int (*prepare_transfer_hardware)(struct spi_controller *ctlr);
        int (*transfer_one_message)(struct spi_controller *ctlr,
                                    struct spi_message *mesg);
        int (*unprepare_transfer_hardware)(struct spi_controller *ctlr);
        int (*prepare_message)(struct spi_controller *ctlr,
                               struct spi_message *message);
        int (*unprepare_message)(struct spi_controller *ctlr,
                                 struct spi_message *message);
        union {
                int (*slave_abort)(struct spi_controller *ctlr);
                int (*target_abort)(struct spi_controller *ctlr);
        };

        /*
         * These hooks are for drivers that use a generic implementation
         * of transfer_one_message() provided by the core.
         */
        void (*set_cs)(struct spi_device *spi, bool enable);
        int (*transfer_one)(struct spi_controller *ctlr, struct spi_device *spi,
                            struct spi_transfer *transfer);
        void (*handle_err)(struct spi_controller *ctlr,
                           struct spi_message *message);

        /* Optimized handlers for SPI memory-like operations. */
        const struct spi_controller_mem_ops *mem_ops;
        const struct spi_controller_mem_caps *mem_caps;

        /* GPIO chip select */
        struct gpio_desc        **cs_gpiods;
        bool                    use_gpio_descriptors;
        s8                      unused_native_cs;
        s8                      max_native_cs;

        /* Statistics */
        struct spi_statistics __percpu  *pcpu_statistics;

        /* DMA channels for use with core dmaengine helpers */
        struct dma_chan         *dma_tx;
        struct dma_chan         *dma_rx;

        /* Dummy data for full duplex devices */
        void                    *dummy_rx;
        void                    *dummy_tx;

        int (*fw_translate_cs)(struct spi_controller *ctlr, unsigned cs);

        /*
         * Driver sets this field to indicate it is able to snapshot SPI
         * transfers (needed e.g. for reading the time of POSIX clocks)
         */
        bool                    ptp_sts_supported;

        /* Interrupt enable state during PTP system timestamping */
        unsigned long           irq_flags;

        /* Flag for enabling opportunistic skipping of the queue in spi_sync */
        bool                    queue_empty;
        bool                    must_async;
};

static inline void *spi_controller_get_devdata(struct spi_controller *ctlr)
{
        return dev_get_drvdata(&ctlr->dev);
}

static inline void spi_controller_set_devdata(struct spi_controller *ctlr,
                                              void *data)
{
        dev_set_drvdata(&ctlr->dev, data);
}

static inline struct spi_controller *spi_controller_get(struct spi_controller *ctlr)
{
        if (!ctlr || !get_device(&ctlr->dev))
                return NULL;
        return ctlr;
}

static inline void spi_controller_put(struct spi_controller *ctlr)
{
        if (ctlr)
                put_device(&ctlr->dev);
}

static inline bool spi_controller_is_slave(struct spi_controller *ctlr)
{
        return IS_ENABLED(CONFIG_SPI_SLAVE) && ctlr->slave;
}

static inline bool spi_controller_is_target(struct spi_controller *ctlr)
{
        return IS_ENABLED(CONFIG_SPI_SLAVE) && ctlr->target;
}

/* PM calls that need to be issued by the driver */
extern int spi_controller_suspend(struct spi_controller *ctlr);
extern int spi_controller_resume(struct spi_controller *ctlr);

/* Calls the driver make to interact with the message queue */
extern struct spi_message *spi_get_next_queued_message(struct spi_controller *ctlr);
extern void spi_finalize_current_message(struct spi_controller *ctlr);
extern void spi_finalize_current_transfer(struct spi_controller *ctlr);

/* Helper calls for driver to timestamp transfer */
void spi_take_timestamp_pre(struct spi_controller *ctlr,
                            struct spi_transfer *xfer,
                            size_t progress, bool irqs_off);
void spi_take_timestamp_post(struct spi_controller *ctlr,
                             struct spi_transfer *xfer,
                             size_t progress, bool irqs_off);

/* The SPI driver core manages memory for the spi_controller classdev */
extern struct spi_controller *__spi_alloc_controller(struct device *host,
                                                unsigned int size, bool slave);

static inline struct spi_controller *spi_alloc_master(struct device *host,
                                                      unsigned int size)
{
        return __spi_alloc_controller(host, size, false);
}

static inline struct spi_controller *spi_alloc_slave(struct device *host,
                                                     unsigned int size)
{
        if (!IS_ENABLED(CONFIG_SPI_SLAVE))
                return NULL;

        return __spi_alloc_controller(host, size, true);
}

static inline struct spi_controller *spi_alloc_host(struct device *dev,
                                                    unsigned int size)
{
        return __spi_alloc_controller(dev, size, false);
}

static inline struct spi_controller *spi_alloc_target(struct device *dev,
                                                      unsigned int size)
{
        if (!IS_ENABLED(CONFIG_SPI_SLAVE))
                return NULL;

        return __spi_alloc_controller(dev, size, true);
}

struct spi_controller *__devm_spi_alloc_controller(struct device *dev,
                                                   unsigned int size,
                                                   bool slave);

static inline struct spi_controller *devm_spi_alloc_master(struct device *dev,
                                                           unsigned int size)
{
        return __devm_spi_alloc_controller(dev, size, false);
}

static inline struct spi_controller *devm_spi_alloc_slave(struct device *dev,
                                                          unsigned int size)
{
        if (!IS_ENABLED(CONFIG_SPI_SLAVE))
                return NULL;

        return __devm_spi_alloc_controller(dev, size, true);
}

static inline struct spi_controller *devm_spi_alloc_host(struct device *dev,
                                                         unsigned int size)
{
        return __devm_spi_alloc_controller(dev, size, false);
}

static inline struct spi_controller *devm_spi_alloc_target(struct device *dev,
                                                           unsigned int size)
{
        if (!IS_ENABLED(CONFIG_SPI_SLAVE))
                return NULL;

        return __devm_spi_alloc_controller(dev, size, true);
}

extern int spi_register_controller(struct spi_controller *ctlr);
extern int devm_spi_register_controller(struct device *dev,
                                        struct spi_controller *ctlr);
extern void spi_unregister_controller(struct spi_controller *ctlr);

#if IS_ENABLED(CONFIG_ACPI)
extern struct spi_controller *acpi_spi_find_controller_by_adev(struct acpi_device *adev);
extern struct spi_device *acpi_spi_device_alloc(struct spi_controller *ctlr,
                                                struct acpi_device *adev,
                                                int index);
int acpi_spi_count_resources(struct acpi_device *adev);
#endif

/*
 * SPI resource management while processing a SPI message
 */

typedef void (*spi_res_release_t)(struct spi_controller *ctlr,
                                  struct spi_message *msg,
                                  void *res);

/**
 * struct spi_res - SPI resource management structure
 * @entry:   list entry
 * @release: release code called prior to freeing this resource
 * @data:    extra data allocated for the specific use-case
 *
 * This is based on ideas from devres, but focused on life-cycle
 * management during spi_message processing.
 */
struct spi_res {
        struct list_head        entry;
        spi_res_release_t       release;
        unsigned long long      data[]; /* Guarantee ull alignment */
};

/*---------------------------------------------------------------------------*/

/*
 * I/O INTERFACE between SPI controller and protocol drivers
 *
 * Protocol drivers use a queue of spi_messages, each transferring data
 * between the controller and memory buffers.
 *
 * The spi_messages themselves consist of a series of read+write transfer
 * segments.  Those segments always read the same number of bits as they
 * write; but one or the other is easily ignored by passing a NULL buffer
 * pointer.  (This is unlike most types of I/O API, because SPI hardware
 * is full duplex.)
 *
 * NOTE:  Allocation of spi_transfer and spi_message memory is entirely
 * up to the protocol driver, which guarantees the integrity of both (as
 * well as the data buffers) for as long as the message is queued.
 */

/**
 * struct spi_transfer - a read/write buffer pair
 * @tx_buf: data to be written (DMA-safe memory), or NULL
 * @rx_buf: data to be read (DMA-safe memory), or NULL
 * @tx_dma: DMA address of tx_buf, if @spi_message.is_dma_mapped
 * @rx_dma: DMA address of rx_buf, if @spi_message.is_dma_mapped
 * @tx_nbits: number of bits used for writing. If 0 the default
 *      (SPI_NBITS_SINGLE) is used.
 * @rx_nbits: number of bits used for reading. If 0 the default
 *      (SPI_NBITS_SINGLE) is used.
 * @len: size of rx and tx buffers (in bytes)
 * @speed_hz: Select a speed other than the device default for this
 *      transfer. If 0 the default (from @spi_device) is used.
 * @bits_per_word: select a bits_per_word other than the device default
 *      for this transfer. If 0 the default (from @spi_device) is used.
 * @dummy_data: indicates transfer is dummy bytes transfer.
 * @cs_off: performs the transfer with chipselect off.
 * @cs_change: affects chipselect after this transfer completes
 * @cs_change_delay: delay between cs deassert and assert when
 *      @cs_change is set and @spi_transfer is not the last in @spi_message
 * @delay: delay to be introduced after this transfer before
 *      (optionally) changing the chipselect status, then starting
 *      the next transfer or completing this @spi_message.
 * @word_delay: inter word delay to be introduced after each word size
 *      (set by bits_per_word) transmission.
 * @effective_speed_hz: the effective SCK-speed that was used to
 *      transfer this transfer. Set to 0 if the SPI bus driver does
 *      not support it.
 * @transfer_list: transfers are sequenced through @spi_message.transfers
 * @tx_sg: Scatterlist for transmit, currently not for client use
 * @rx_sg: Scatterlist for receive, currently not for client use
 * @ptp_sts_word_pre: The word (subject to bits_per_word semantics) offset
 *      within @tx_buf for which the SPI device is requesting that the time
 *      snapshot for this transfer begins. Upon completing the SPI transfer,
 *      this value may have changed compared to what was requested, depending
 *      on the available snapshotting resolution (DMA transfer,
 *      @ptp_sts_supported is false, etc).
 * @ptp_sts_word_post: See @ptp_sts_word_post. The two can be equal (meaning
 *      that a single byte should be snapshotted).
 *      If the core takes care of the timestamp (if @ptp_sts_supported is false
 *      for this controller), it will set @ptp_sts_word_pre to 0, and
 *      @ptp_sts_word_post to the length of the transfer. This is done
 *      purposefully (instead of setting to spi_transfer->len - 1) to denote
 *      that a transfer-level snapshot taken from within the driver may still
 *      be of higher quality.
 * @ptp_sts: Pointer to a memory location held by the SPI slave device where a
 *      PTP system timestamp structure may lie. If drivers use PIO or their
 *      hardware has some sort of assist for retrieving exact transfer timing,
 *      they can (and should) assert @ptp_sts_supported and populate this
 *      structure using the ptp_read_system_*ts helper functions.
 *      The timestamp must represent the time at which the SPI slave device has
 *      processed the word, i.e. the "pre" timestamp should be taken before
 *      transmitting the "pre" word, and the "post" timestamp after receiving
 *      transmit confirmation from the controller for the "post" word.
 * @timestamped: true if the transfer has been timestamped
 * @error: Error status logged by SPI controller driver.
 *
 * SPI transfers always write the same number of bytes as they read.
 * Protocol drivers should always provide @rx_buf and/or @tx_buf.
 * In some cases, they may also want to provide DMA addresses for
 * the data being transferred; that may reduce overhead, when the
 * underlying driver uses DMA.
 *
 * If the transmit buffer is NULL, zeroes will be shifted out
 * while filling @rx_buf.  If the receive buffer is NULL, the data
 * shifted in will be discarded.  Only "len" bytes shift out (or in).
 * It's an error to try to shift out a partial word.  (For example, by
 * shifting out three bytes with word size of sixteen or twenty bits;
 * the former uses two bytes per word, the latter uses four bytes.)
 *
 * In-memory data values are always in native CPU byte order, translated
 * from the wire byte order (big-endian except with SPI_LSB_FIRST).  So
 * for example when bits_per_word is sixteen, buffers are 2N bytes long
 * (@len = 2N) and hold N sixteen bit words in CPU byte order.
 *
 * When the word size of the SPI transfer is not a power-of-two multiple
 * of eight bits, those in-memory words include extra bits.  In-memory
 * words are always seen by protocol drivers as right-justified, so the
 * undefined (rx) or unused (tx) bits are always the most significant bits.
 *
 * All SPI transfers start with the relevant chipselect active.  Normally
 * it stays selected until after the last transfer in a message.  Drivers
 * can affect the chipselect signal using cs_change.
 *
 * (i) If the transfer isn't the last one in the message, this flag is
 * used to make the chipselect briefly go inactive in the middle of the
 * message.  Toggling chipselect in this way may be needed to terminate
 * a chip command, letting a single spi_message perform all of group of
 * chip transactions together.
 *
 * (ii) When the transfer is the last one in the message, the chip may
 * stay selected until the next transfer.  On multi-device SPI busses
 * with nothing blocking messages going to other devices, this is just
 * a performance hint; starting a message to another device deselects
 * this one.  But in other cases, this can be used to ensure correctness.
 * Some devices need protocol transactions to be built from a series of
 * spi_message submissions, where the content of one message is determined
 * by the results of previous messages and where the whole transaction
 * ends when the chipselect goes inactive.
 *
 * When SPI can transfer in 1x,2x or 4x. It can get this transfer information
 * from device through @tx_nbits and @rx_nbits. In Bi-direction, these
 * two should both be set. User can set transfer mode with SPI_NBITS_SINGLE(1x)
 * SPI_NBITS_DUAL(2x) and SPI_NBITS_QUAD(4x) to support these three transfer.
 *
 * The code that submits an spi_message (and its spi_transfers)
 * to the lower layers is responsible for managing its memory.
 * Zero-initialize every field you don't set up explicitly, to
 * insulate against future API updates.  After you submit a message
 * and its transfers, ignore them until its completion callback.
 */
struct spi_transfer {
        /*
         * It's okay if tx_buf == rx_buf (right?).
         * For MicroWire, one buffer must be NULL.
         * Buffers must work with dma_*map_single() calls, unless
         * spi_message.is_dma_mapped reports a pre-existing mapping.
         */
        const void      *tx_buf;
        void            *rx_buf;
        unsigned        len;

#define SPI_TRANS_FAIL_NO_START BIT(0)
#define SPI_TRANS_FAIL_IO       BIT(1)
        u16             error;

        dma_addr_t      tx_dma;
        dma_addr_t      rx_dma;
        struct sg_table tx_sg;
        struct sg_table rx_sg;

        unsigned        dummy_data:1;
        unsigned        cs_off:1;
        unsigned        cs_change:1;
        unsigned        tx_nbits:3;
        unsigned        rx_nbits:3;
        unsigned        timestamped:1;
#define SPI_NBITS_SINGLE        0x01 /* 1-bit transfer */
#define SPI_NBITS_DUAL          0x02 /* 2-bit transfer */
#define SPI_NBITS_QUAD          0x04 /* 4-bit transfer */
        u8              bits_per_word;
        struct spi_delay        delay;
        struct spi_delay        cs_change_delay;
        struct spi_delay        word_delay;
        u32             speed_hz;

        u32             effective_speed_hz;

        unsigned int    ptp_sts_word_pre;
        unsigned int    ptp_sts_word_post;

        struct ptp_system_timestamp *ptp_sts;

        struct list_head transfer_list;
};

/**
 * struct spi_message - one multi-segment SPI transaction
 * @transfers: list of transfer segments in this transaction
 * @spi: SPI device to which the transaction is queued
 * @is_dma_mapped: if true, the caller provided both DMA and CPU virtual
 *      addresses for each transfer buffer
 * @complete: called to report transaction completions
 * @context: the argument to complete() when it's called
 * @frame_length: the total number of bytes in the message
 * @actual_length: the total number of bytes that were transferred in all
 *      successful segments
 * @status: zero for success, else negative errno
 * @queue: for use by whichever driver currently owns the message
 * @state: for use by whichever driver currently owns the message
 * @resources: for resource management when the SPI message is processed
 * @prepared: spi_prepare_message was called for the this message
 *
 * A @spi_message is used to execute an atomic sequence of data transfers,
 * each represented by a struct spi_transfer.  The sequence is "atomic"
 * in the sense that no other spi_message may use that SPI bus until that
 * sequence completes.  On some systems, many such sequences can execute as
 * a single programmed DMA transfer.  On all systems, these messages are
 * queued, and might complete after transactions to other devices.  Messages
 * sent to a given spi_device are always executed in FIFO order.
 *
 * The code that submits an spi_message (and its spi_transfers)
 * to the lower layers is responsible for managing its memory.
 * Zero-initialize every field you don't set up explicitly, to
 * insulate against future API updates.  After you submit a message
 * and its transfers, ignore them until its completion callback.
 */
struct spi_message {
        struct list_head        transfers;

        struct spi_device       *spi;

        unsigned                is_dma_mapped:1;

        /* spi_prepare_message() was called for this message */
        bool                    prepared;

        /*
         * REVISIT: we might want a flag affecting the behavior of the
         * last transfer ... allowing things like "read 16 bit length L"
         * immediately followed by "read L bytes".  Basically imposing
         * a specific message scheduling algorithm.
         *
         * Some controller drivers (message-at-a-time queue processing)
         * could provide that as their default scheduling algorithm.  But
         * others (with multi-message pipelines) could need a flag to
         * tell them about such special cases.
         */

        /* Completion is reported through a callback */
        int                     status;
        void                    (*complete)(void *context);
        void                    *context;
        unsigned                frame_length;
        unsigned                actual_length;

        /*
         * For optional use by whatever driver currently owns the
         * spi_message ...  between calls to spi_async and then later
         * complete(), that's the spi_controller controller driver.
         */
        struct list_head        queue;
        void                    *state;

        /* List of spi_res resources when the SPI message is processed */
        struct list_head        resources;
};

static inline void spi_message_init_no_memset(struct spi_message *m)
{
        INIT_LIST_HEAD(&m->transfers);
        INIT_LIST_HEAD(&m->resources);
}

static inline void spi_message_init(struct spi_message *m)
{
        memset(m, 0, sizeof *m);
        spi_message_init_no_memset(m);
}

static inline void
spi_message_add_tail(struct spi_transfer *t, struct spi_message *m)
{
        list_add_tail(&t->transfer_list, &m->transfers);
}

static inline void
spi_transfer_del(struct spi_transfer *t)
{
        list_del(&t->transfer_list);
}

static inline int
spi_transfer_delay_exec(struct spi_transfer *t)
{
        return spi_delay_exec(&t->delay, t);
}

/**
 * spi_message_init_with_transfers - Initialize spi_message and append transfers
 * @m: spi_message to be initialized
 * @xfers: An array of SPI transfers
 * @num_xfers: Number of items in the xfer array
 *
 * This function initializes the given spi_message and adds each spi_transfer in
 * the given array to the message.
 */
static inline void
spi_message_init_with_transfers(struct spi_message *m,
struct spi_transfer *xfers, unsigned int num_xfers)
{
        unsigned int i;

        spi_message_init(m);
        for (i = 0; i < num_xfers; ++i)
                spi_message_add_tail(&xfers[i], m);
}

/*
 * It's fine to embed message and transaction structures in other data
 * structures so long as you don't free them while they're in use.
 */
static inline struct spi_message *spi_message_alloc(unsigned ntrans, gfp_t flags)
{
        struct spi_message_with_transfers {
                struct spi_message m;
                struct spi_transfer t[];
        } *mwt;
        unsigned i;

        mwt = kzalloc(struct_size(mwt, t, ntrans), flags);
        if (!mwt)
                return NULL;

        spi_message_init_no_memset(&mwt->m);
        for (i = 0; i < ntrans; i++)
                spi_message_add_tail(&mwt->t[i], &mwt->m);

        return &mwt->m;
}

static inline void spi_message_free(struct spi_message *m)
{
        kfree(m);
}

extern int spi_setup(struct spi_device *spi);
extern int spi_async(struct spi_device *spi, struct spi_message *message);
extern int spi_slave_abort(struct spi_device *spi);
extern int spi_target_abort(struct spi_device *spi);

static inline size_t
spi_max_message_size(struct spi_device *spi)
{
        struct spi_controller *ctlr = spi->controller;

        if (!ctlr->max_message_size)
                return SIZE_MAX;
        return ctlr->max_message_size(spi);
}

static inline size_t
spi_max_transfer_size(struct spi_device *spi)
{
        struct spi_controller *ctlr = spi->controller;
        size_t tr_max = SIZE_MAX;
        size_t msg_max = spi_max_message_size(spi);

        if (ctlr->max_transfer_size)
                tr_max = ctlr->max_transfer_size(spi);

        /* Transfer size limit must not be greater than message size limit */
        return min(tr_max, msg_max);
}

/**
 * spi_is_bpw_supported - Check if bits per word is supported
 * @spi: SPI device
 * @bpw: Bits per word
 *
 * This function checks to see if the SPI controller supports @bpw.
 *
 * Returns:
 * True if @bpw is supported, false otherwise.
 */
static inline bool spi_is_bpw_supported(struct spi_device *spi, u32 bpw)
{
        u32 bpw_mask = spi->master->bits_per_word_mask;

        if (bpw == 8 || (bpw <= 32 && bpw_mask & SPI_BPW_MASK(bpw)))
                return true;

        return false;
}

/**
 * spi_controller_xfer_timeout - Compute a suitable timeout value
 * @ctlr: SPI device
 * @xfer: Transfer descriptor
 *
 * Compute a relevant timeout value for the given transfer. We derive the time
 * that it would take on a single data line and take twice this amount of time
 * with a minimum of 500ms to avoid false positives on loaded systems.
 *
 * Returns: Transfer timeout value in milliseconds.
 */
static inline unsigned int spi_controller_xfer_timeout(struct spi_controller *ctlr,
                                                       struct spi_transfer *xfer)
{
        return max(xfer->len * 8 * 2 / (xfer->speed_hz / 1000), 500U);
}

/*---------------------------------------------------------------------------*/

/* SPI transfer replacement methods which make use of spi_res */

struct spi_replaced_transfers;
typedef void (*spi_replaced_release_t)(struct spi_controller *ctlr,
                                       struct spi_message *msg,
                                       struct spi_replaced_transfers *res);
/**
 * struct spi_replaced_transfers - structure describing the spi_transfer
 *                                 replacements that have occurred
 *                                 so that they can get reverted
 * @release:            some extra release code to get executed prior to
 *                      releasing this structure
 * @extradata:          pointer to some extra data if requested or NULL
 * @replaced_transfers: transfers that have been replaced and which need
 *                      to get restored
 * @replaced_after:     the transfer after which the @replaced_transfers
 *                      are to get re-inserted
 * @inserted:           number of transfers inserted
 * @inserted_transfers: array of spi_transfers of array-size @inserted,
 *                      that have been replacing replaced_transfers
 *
 * Note: that @extradata will point to @inserted_transfers[@inserted]
 * if some extra allocation is requested, so alignment will be the same
 * as for spi_transfers.
 */
struct spi_replaced_transfers {
        spi_replaced_release_t release;
        void *extradata;
        struct list_head replaced_transfers;
        struct list_head *replaced_after;
        size_t inserted;
        struct spi_transfer inserted_transfers[];
};

/*---------------------------------------------------------------------------*/

/* SPI transfer transformation methods */

extern int spi_split_transfers_maxsize(struct spi_controller *ctlr,
                                       struct spi_message *msg,
                                       size_t maxsize,
                                       gfp_t gfp);
extern int spi_split_transfers_maxwords(struct spi_controller *ctlr,
                                        struct spi_message *msg,
                                        size_t maxwords,
                                        gfp_t gfp);

/*---------------------------------------------------------------------------*/

/*
 * All these synchronous SPI transfer routines are utilities layered
 * over the core async transfer primitive.  Here, "synchronous" means
 * they will sleep uninterruptibly until the async transfer completes.
 */

extern int spi_sync(struct spi_device *spi, struct spi_message *message);
extern int spi_sync_locked(struct spi_device *spi, struct spi_message *message);
extern int spi_bus_lock(struct spi_controller *ctlr);
extern int spi_bus_unlock(struct spi_controller *ctlr);

/**
 * spi_sync_transfer - synchronous SPI data transfer
 * @spi: device with which data will be exchanged
 * @xfers: An array of spi_transfers
 * @num_xfers: Number of items in the xfer array
 * Context: can sleep
 *
 * Does a synchronous SPI data transfer of the given spi_transfer array.
 *
 * For more specific semantics see spi_sync().
 *
 * Return: zero on success, else a negative error code.
 */
static inline int
spi_sync_transfer(struct spi_device *spi, struct spi_transfer *xfers,
        unsigned int num_xfers)
{
        struct spi_message msg;

        spi_message_init_with_transfers(&msg, xfers, num_xfers);

        return spi_sync(spi, &msg);
}

/**
 * spi_write - SPI synchronous write
 * @spi: device to which data will be written
 * @buf: data buffer
 * @len: data buffer size
 * Context: can sleep
 *
 * This function writes the buffer @buf.
 * Callable only from contexts that can sleep.
 *
 * Return: zero on success, else a negative error code.
 */
static inline int
spi_write(struct spi_device *spi, const void *buf, size_t len)
{
        struct spi_transfer     t = {
                        .tx_buf         = buf,
                        .len            = len,
                };

        return spi_sync_transfer(spi, &t, 1);
}

/**
 * spi_read - SPI synchronous read
 * @spi: device from which data will be read
 * @buf: data buffer
 * @len: data buffer size
 * Context: can sleep
 *
 * This function reads the buffer @buf.
 * Callable only from contexts that can sleep.
 *
 * Return: zero on success, else a negative error code.
 */
static inline int
spi_read(struct spi_device *spi, void *buf, size_t len)
{
        struct spi_transfer     t = {
                        .rx_buf         = buf,
                        .len            = len,
                };

        return spi_sync_transfer(spi, &t, 1);
}

/* This copies txbuf and rxbuf data; for small transfers only! */
extern int spi_write_then_read(struct spi_device *spi,
                const void *txbuf, unsigned n_tx,
                void *rxbuf, unsigned n_rx);

/**
 * spi_w8r8 - SPI synchronous 8 bit write followed by 8 bit read
 * @spi: device with which data will be exchanged
 * @cmd: command to be written before data is read back
 * Context: can sleep
 *
 * Callable only from contexts that can sleep.
 *
 * Return: the (unsigned) eight bit number returned by the
 * device, or else a negative error code.
 */
static inline ssize_t spi_w8r8(struct spi_device *spi, u8 cmd)
{
        ssize_t                 status;
        u8                      result;

        status = spi_write_then_read(spi, &cmd, 1, &result, 1);

        /* Return negative errno or unsigned value */
        return (status < 0) ? status : result;
}

/**
 * spi_w8r16 - SPI synchronous 8 bit write followed by 16 bit read
 * @spi: device with which data will be exchanged
 * @cmd: command to be written before data is read back
 * Context: can sleep
 *
 * The number is returned in wire-order, which is at least sometimes
 * big-endian.
 *
 * Callable only from contexts that can sleep.
 *
 * Return: the (unsigned) sixteen bit number returned by the
 * device, or else a negative error code.
 */
static inline ssize_t spi_w8r16(struct spi_device *spi, u8 cmd)
{
        ssize_t                 status;
        u16                     result;

        status = spi_write_then_read(spi, &cmd, 1, &result, 2);

        /* Return negative errno or unsigned value */
        return (status < 0) ? status : result;
}

/**
 * spi_w8r16be - SPI synchronous 8 bit write followed by 16 bit big-endian read
 * @spi: device with which data will be exchanged
 * @cmd: command to be written before data is read back
 * Context: can sleep
 *
 * This function is similar to spi_w8r16, with the exception that it will
 * convert the read 16 bit data word from big-endian to native endianness.
 *
 * Callable only from contexts that can sleep.
 *
 * Return: the (unsigned) sixteen bit number returned by the device in CPU
 * endianness, or else a negative error code.
 */
static inline ssize_t spi_w8r16be(struct spi_device *spi, u8 cmd)

{
        ssize_t status;
        __be16 result;

        status = spi_write_then_read(spi, &cmd, 1, &result, 2);
        if (status < 0)
                return status;

        return be16_to_cpu(result);
}

/*---------------------------------------------------------------------------*/

/*
 * INTERFACE between board init code and SPI infrastructure.
 *
 * No SPI driver ever sees these SPI device table segments, but
 * it's how the SPI core (or adapters that get hotplugged) grows
 * the driver model tree.
 *
 * As a rule, SPI devices can't be probed.  Instead, board init code
 * provides a table listing the devices which are present, with enough
 * information to bind and set up the device's driver.  There's basic
 * support for non-static configurations too; enough to handle adding
 * parport adapters, or microcontrollers acting as USB-to-SPI bridges.
 */

/**
 * struct spi_board_info - board-specific template for a SPI device
 * @modalias: Initializes spi_device.modalias; identifies the driver.
 * @platform_data: Initializes spi_device.platform_data; the particular
 *      data stored there is driver-specific.
 * @swnode: Software node for the device.
 * @controller_data: Initializes spi_device.controller_data; some
 *      controllers need hints about hardware setup, e.g. for DMA.
 * @irq: Initializes spi_device.irq; depends on how the board is wired.
 * @max_speed_hz: Initializes spi_device.max_speed_hz; based on limits
 *      from the chip datasheet and board-specific signal quality issues.
 * @bus_num: Identifies which spi_controller parents the spi_device; unused
 *      by spi_new_device(), and otherwise depends on board wiring.
 * @chip_select: Initializes spi_device.chip_select; depends on how
 *      the board is wired.
 * @mode: Initializes spi_device.mode; based on the chip datasheet, board
 *      wiring (some devices support both 3WIRE and standard modes), and
 *      possibly presence of an inverter in the chipselect path.
 *
 * When adding new SPI devices to the device tree, these structures serve
 * as a partial device template.  They hold information which can't always
 * be determined by drivers.  Information that probe() can establish (such
 * as the default transfer wordsize) is not included here.
 *
 * These structures are used in two places.  Their primary role is to
 * be stored in tables of board-specific device descriptors, which are
 * declared early in board initialization and then used (much later) to
 * populate a controller's device tree after the that controller's driver
 * initializes.  A secondary (and atypical) role is as a parameter to
 * spi_new_device() call, which happens after those controller drivers
 * are active in some dynamic board configuration models.
 */
struct spi_board_info {
        /*
         * The device name and module name are coupled, like platform_bus;
         * "modalias" is normally the driver name.
         *
         * platform_data goes to spi_device.dev.platform_data,
         * controller_data goes to spi_device.controller_data,
         * IRQ is copied too.
         */
        char            modalias[SPI_NAME_SIZE];
        const void      *platform_data;
        const struct software_node *swnode;
        void            *controller_data;
        int             irq;

        /* Slower signaling on noisy or low voltage boards */
        u32             max_speed_hz;


        /*
         * bus_num is board specific and matches the bus_num of some
         * spi_controller that will probably be registered later.
         *
         * chip_select reflects how this chip is wired to that master;
         * it's less than num_chipselect.
         */
        u16             bus_num;
        u16             chip_select;

        /*
         * mode becomes spi_device.mode, and is essential for chips
         * where the default of SPI_CS_HIGH = 0 is wrong.
         */
        u32             mode;

        /*
         * ... may need additional spi_device chip config data here.
         * avoid stuff protocol drivers can set; but include stuff
         * needed to behave without being bound to a driver:
         *  - quirks like clock rate mattering when not selected
         */
};

#ifdef  CONFIG_SPI
extern int
spi_register_board_info(struct spi_board_info const *info, unsigned n);
#else
/* Board init code may ignore whether SPI is configured or not */
static inline int
spi_register_board_info(struct spi_board_info const *info, unsigned n)
        { return 0; }
#endif

/*
 * If you're hotplugging an adapter with devices (parport, USB, etc)
 * use spi_new_device() to describe each device.  You can also call
 * spi_unregister_device() to start making that device vanish, but
 * normally that would be handled by spi_unregister_controller().
 *
 * You can also use spi_alloc_device() and spi_add_device() to use a two
 * stage registration sequence for each spi_device. This gives the caller
 * some more control over the spi_device structure before it is registered,
 * but requires that caller to initialize fields that would otherwise
 * be defined using the board info.
 */
extern struct spi_device *
spi_alloc_device(struct spi_controller *ctlr);

extern int
spi_add_device(struct spi_device *spi);

extern struct spi_device *
spi_new_device(struct spi_controller *, struct spi_board_info *);

extern void spi_unregister_device(struct spi_device *spi);

extern const struct spi_device_id *
spi_get_device_id(const struct spi_device *sdev);

extern const void *
spi_get_device_match_data(const struct spi_device *sdev);

static inline bool
spi_transfer_is_last(struct spi_controller *ctlr, struct spi_transfer *xfer)
{
        return list_is_last(&xfer->transfer_list, &ctlr->cur_msg->transfers);
}

/* Compatibility layer */
#define spi_master                      spi_controller

#define spi_master_get_devdata(_ctlr)   spi_controller_get_devdata(_ctlr)
#define spi_master_set_devdata(_ctlr, _data)    \
        spi_controller_set_devdata(_ctlr, _data)
#define spi_master_get(_ctlr)           spi_controller_get(_ctlr)
#define spi_master_put(_ctlr)           spi_controller_put(_ctlr)
#define spi_master_suspend(_ctlr)       spi_controller_suspend(_ctlr)
#define spi_master_resume(_ctlr)        spi_controller_resume(_ctlr)

#define spi_register_master(_ctlr)      spi_register_controller(_ctlr)
#define devm_spi_register_master(_dev, _ctlr) \
        devm_spi_register_controller(_dev, _ctlr)
#define spi_unregister_master(_ctlr)    spi_unregister_controller(_ctlr)

#endif /* __LINUX_SPI_H */