drivers/usb/dwc3/core.c

   1 // SPDX-License-Identifier: GPL-2.0
   2 /**
   3  * core.c - DesignWare USB3 DRD Controller Core file
   4  *
   5  * Copyright (C) 2010-2011 Texas Instruments Incorporated - http://www.ti.com
   6  *
   7  * Authors: Felipe Balbi <[email protected]>,
   8  *          Sebastian Andrzej Siewior <[email protected]>
   9  */
  10
  11 #include <linux/clk.h>
  12 #include <linux/version.h>
  13 #include <linux/module.h>
  14 #include <linux/kernel.h>
  15 #include <linux/slab.h>
  16 #include <linux/spinlock.h>
  17 #include <linux/platform_device.h>
  18 #include <linux/pm_runtime.h>
  19 #include <linux/interrupt.h>
  20 #include <linux/ioport.h>
  21 #include <linux/io.h>
  22 #include <linux/list.h>
  23 #include <linux/delay.h>
  24 #include <linux/dma-mapping.h>
  25 #include <linux/of.h>
  26 #include <linux/acpi.h>
  27 #include <linux/pinctrl/consumer.h>
  28 #include <linux/reset.h>
  29
  30 #include <linux/usb/ch9.h>
  31 #include <linux/usb/gadget.h>
  32 #include <linux/usb/of.h>
  33 #include <linux/usb/otg.h>
  34
  35 #include "core.h"
  36 #include "gadget.h"
  37 #include "io.h"
  38
  39 #include "debug.h"
  40
  41 #define DWC3_DEFAULT_AUTOSUSPEND_DELAY  5000 /* ms */
  42
  43 /**
  44  * dwc3_get_dr_mode - Validates and sets dr_mode
  45  * @dwc: pointer to our context structure
  46  */
  47 static int dwc3_get_dr_mode(struct dwc3 *dwc)
  48 {
  49         enum usb_dr_mode mode;
  50         struct device *dev = dwc->dev;
  51         unsigned int hw_mode;
  52
  53         if (dwc->dr_mode == USB_DR_MODE_UNKNOWN)
  54                 dwc->dr_mode = USB_DR_MODE_OTG;
  55
  56         mode = dwc->dr_mode;
  57         hw_mode = DWC3_GHWPARAMS0_MODE(dwc->hwparams.hwparams0);
  58
  59         switch (hw_mode) {
  60         case DWC3_GHWPARAMS0_MODE_GADGET:
  61                 if (IS_ENABLED(CONFIG_USB_DWC3_HOST)) {
  62                         dev_err(dev,
  63                                 "Controller does not support host mode.\n");
  64                         return -EINVAL;
  65                 }
  66                 mode = USB_DR_MODE_PERIPHERAL;
  67                 break;
  68         case DWC3_GHWPARAMS0_MODE_HOST:
  69                 if (IS_ENABLED(CONFIG_USB_DWC3_GADGET)) {
  70                         dev_err(dev,
  71                                 "Controller does not support device mode.\n");
  72                         return -EINVAL;
  73                 }
  74                 mode = USB_DR_MODE_HOST;
  75                 break;
  76         default:
  77                 if (IS_ENABLED(CONFIG_USB_DWC3_HOST))
  78                         mode = USB_DR_MODE_HOST;
  79                 else if (IS_ENABLED(CONFIG_USB_DWC3_GADGET))
  80                         mode = USB_DR_MODE_PERIPHERAL;
  81
  82                 /*
  83                  * DWC_usb31 and DWC_usb3 v3.30a and higher do not support OTG
  84                  * mode. If the controller supports DRD but the dr_mode is not
  85                  * specified or set to OTG, then set the mode to peripheral.
  86                  */
  87                 if (mode == USB_DR_MODE_OTG &&
  88                     dwc->revision >= DWC3_REVISION_330A)
  89                         mode = USB_DR_MODE_PERIPHERAL;
  90         }
  91
  92         if (mode != dwc->dr_mode) {
  93                 dev_warn(dev,
  94                          "Configuration mismatch. dr_mode forced to %s\n",
  95                          mode == USB_DR_MODE_HOST ? "host" : "gadget");
  96
  97                 dwc->dr_mode = mode;
  98         }
  99
 100         return 0;
 101 }
 102
 103 void dwc3_set_prtcap(struct dwc3 *dwc, u32 mode)
 104 {
 105         u32 reg;
 106
 107         reg = dwc3_readl(dwc->regs, DWC3_GCTL);
 108         reg &= ~(DWC3_GCTL_PRTCAPDIR(DWC3_GCTL_PRTCAP_OTG));
 109         reg |= DWC3_GCTL_PRTCAPDIR(mode);
 110         dwc3_writel(dwc->regs, DWC3_GCTL, reg);
 111
 112         dwc->current_dr_role = mode;
 113 }
 114
 115 static void __dwc3_set_mode(struct work_struct *work)
 116 {
 117         struct dwc3 *dwc = work_to_dwc(work);
 118         unsigned long flags;
 119         int ret;
 120
 121         if (dwc->dr_mode != USB_DR_MODE_OTG)
 122                 return;
 123
 124         if (dwc->current_dr_role == DWC3_GCTL_PRTCAP_OTG)
 125                 dwc3_otg_update(dwc, 0);
 126
 127         if (!dwc->desired_dr_role)
 128                 return;
 129
 130         if (dwc->desired_dr_role == dwc->current_dr_role)
 131                 return;
 132
 133         if (dwc->desired_dr_role == DWC3_GCTL_PRTCAP_OTG && dwc->edev)
 134                 return;
 135
 136         switch (dwc->current_dr_role) {
 137         case DWC3_GCTL_PRTCAP_HOST:
 138                 dwc3_host_exit(dwc);
 139                 break;
 140         case DWC3_GCTL_PRTCAP_DEVICE:
 141                 dwc3_gadget_exit(dwc);
 142                 dwc3_event_buffers_cleanup(dwc);
 143                 break;
 144         case DWC3_GCTL_PRTCAP_OTG:
 145                 dwc3_otg_exit(dwc);
 146                 spin_lock_irqsave(&dwc->lock, flags);
 147                 dwc->desired_otg_role = DWC3_OTG_ROLE_IDLE;
 148                 spin_unlock_irqrestore(&dwc->lock, flags);
 149                 dwc3_otg_update(dwc, 1);
 150                 break;
 151         default:
 152                 break;
 153         }
 154
 155         spin_lock_irqsave(&dwc->lock, flags);
 156
 157         dwc3_set_prtcap(dwc, dwc->desired_dr_role);
 158
 159         spin_unlock_irqrestore(&dwc->lock, flags);
 160
 161         switch (dwc->desired_dr_role) {
 162         case DWC3_GCTL_PRTCAP_HOST:
 163                 ret = dwc3_host_init(dwc);
 164                 if (ret) {
 165                         dev_err(dwc->dev, "failed to initialize host\n");
 166                 } else {
 167                         if (dwc->usb2_phy)
 168                                 otg_set_vbus(dwc->usb2_phy->otg, true);
 169                         phy_set_mode(dwc->usb2_generic_phy, PHY_MODE_USB_HOST);
 170                         phy_set_mode(dwc->usb3_generic_phy, PHY_MODE_USB_HOST);
 171                         phy_calibrate(dwc->usb2_generic_phy);
 172                 }
 173                 break;
 174         case DWC3_GCTL_PRTCAP_DEVICE:
 175                 dwc3_event_buffers_setup(dwc);
 176
 177                 if (dwc->usb2_phy)
 178                         otg_set_vbus(dwc->usb2_phy->otg, false);
 179                 phy_set_mode(dwc->usb2_generic_phy, PHY_MODE_USB_DEVICE);
 180                 phy_set_mode(dwc->usb3_generic_phy, PHY_MODE_USB_DEVICE);
 181
 182                 ret = dwc3_gadget_init(dwc);
 183                 if (ret)
 184                         dev_err(dwc->dev, "failed to initialize peripheral\n");
 185                 break;
 186         case DWC3_GCTL_PRTCAP_OTG:
 187                 dwc3_otg_init(dwc);
 188                 dwc3_otg_update(dwc, 0);
 189                 break;
 190         default:
 191                 break;
 192         }
 193
 194 }
 195
 196 void dwc3_set_mode(struct dwc3 *dwc, u32 mode)
 197 {
 198         unsigned long flags;
 199
 200         spin_lock_irqsave(&dwc->lock, flags);
 201         dwc->desired_dr_role = mode;
 202         spin_unlock_irqrestore(&dwc->lock, flags);
 203
 204         queue_work(system_freezable_wq, &dwc->drd_work);
 205 }
 206
 207 u32 dwc3_core_fifo_space(struct dwc3_ep *dep, u8 type)
 208 {
 209         struct dwc3             *dwc = dep->dwc;
 210         u32                     reg;
 211
 212         dwc3_writel(dwc->regs, DWC3_GDBGFIFOSPACE,
 213                         DWC3_GDBGFIFOSPACE_NUM(dep->number) |
 214                         DWC3_GDBGFIFOSPACE_TYPE(type));
 215
 216         reg = dwc3_readl(dwc->regs, DWC3_GDBGFIFOSPACE);
 217
 218         return DWC3_GDBGFIFOSPACE_SPACE_AVAILABLE(reg);
 219 }
 220
 221 /**
 222  * dwc3_core_soft_reset - Issues core soft reset and PHY reset
 223  * @dwc: pointer to our context structure
 224  */
 225 static int dwc3_core_soft_reset(struct dwc3 *dwc)
 226 {
 227         u32             reg;
 228         int             retries = 1000;
 229         int             ret;
 230
 231         usb_phy_init(dwc->usb2_phy);
 232         usb_phy_init(dwc->usb3_phy);
 233         ret = phy_init(dwc->usb2_generic_phy);
 234         if (ret < 0)
 235                 return ret;
 236
 237         ret = phy_init(dwc->usb3_generic_phy);
 238         if (ret < 0) {
 239                 phy_exit(dwc->usb2_generic_phy);
 240                 return ret;
 241         }
 242
 243         /*
 244          * We're resetting only the device side because, if we're in host mode,
 245          * XHCI driver will reset the host block. If dwc3 was configured for
 246          * host-only mode, then we can return early.
 247          */
 248         if (dwc->current_dr_role == DWC3_GCTL_PRTCAP_HOST)
 249                 return 0;
 250
 251         reg = dwc3_readl(dwc->regs, DWC3_DCTL);
 252         reg |= DWC3_DCTL_CSFTRST;
 253         dwc3_writel(dwc->regs, DWC3_DCTL, reg);
 254
 255         do {
 256                 reg = dwc3_readl(dwc->regs, DWC3_DCTL);
 257                 if (!(reg & DWC3_DCTL_CSFTRST))
 258                         goto done;
 259
 260                 udelay(1);
 261         } while (--retries);
 262
 263         phy_exit(dwc->usb3_generic_phy);
 264         phy_exit(dwc->usb2_generic_phy);
 265
 266         return -ETIMEDOUT;
 267
 268 done:
 269         /*
 270          * For DWC_usb31 controller, once DWC3_DCTL_CSFTRST bit is cleared,
 271          * we must wait at least 50ms before accessing the PHY domain
 272          * (synchronization delay). DWC_usb31 programming guide section 1.3.2.
 273          */
 274         if (dwc3_is_usb31(dwc))
 275                 msleep(50);
 276
 277         return 0;
 278 }
 279
 280 static const struct clk_bulk_data dwc3_core_clks[] = {
 281         { .id = "ref" },
 282         { .id = "bus_early" },
 283         { .id = "suspend" },
 284 };
 285
 286 /*
 287  * dwc3_frame_length_adjustment - Adjusts frame length if required
 288  * @dwc3: Pointer to our controller context structure
 289  */
 290 static void dwc3_frame_length_adjustment(struct dwc3 *dwc)
 291 {
 292         u32 reg;
 293         u32 dft;
 294
 295         if (dwc->revision < DWC3_REVISION_250A)
 296                 return;
 297
 298         if (dwc->fladj == 0)
 299                 return;
 300
 301         reg = dwc3_readl(dwc->regs, DWC3_GFLADJ);
 302         dft = reg & DWC3_GFLADJ_30MHZ_MASK;
 303         if (!dev_WARN_ONCE(dwc->dev, dft == dwc->fladj,
 304             "request value same as default, ignoring\n")) {
 305                 reg &= ~DWC3_GFLADJ_30MHZ_MASK;
 306                 reg |= DWC3_GFLADJ_30MHZ_SDBND_SEL | dwc->fladj;
 307                 dwc3_writel(dwc->regs, DWC3_GFLADJ, reg);
 308         }
 309 }
 310
 311 /**
 312  * dwc3_free_one_event_buffer - Frees one event buffer
 313  * @dwc: Pointer to our controller context structure
 314  * @evt: Pointer to event buffer to be freed
 315  */
 316 static void dwc3_free_one_event_buffer(struct dwc3 *dwc,
 317                 struct dwc3_event_buffer *evt)
 318 {
 319         dma_free_coherent(dwc->sysdev, evt->length, evt->buf, evt->dma);
 320 }
 321
 322 /**
 323  * dwc3_alloc_one_event_buffer - Allocates one event buffer structure
 324  * @dwc: Pointer to our controller context structure
 325  * @length: size of the event buffer
 326  *
 327  * Returns a pointer to the allocated event buffer structure on success
 328  * otherwise ERR_PTR(errno).
 329  */
 330 static struct dwc3_event_buffer *dwc3_alloc_one_event_buffer(struct dwc3 *dwc,
 331                 unsigned length)
 332 {
 333         struct dwc3_event_buffer        *evt;
 334
 335         evt = devm_kzalloc(dwc->dev, sizeof(*evt), GFP_KERNEL);
 336         if (!evt)
 337                 return ERR_PTR(-ENOMEM);
 338
 339         evt->dwc        = dwc;
 340         evt->length     = length;
 341         evt->cache      = devm_kzalloc(dwc->dev, length, GFP_KERNEL);
 342         if (!evt->cache)
 343                 return ERR_PTR(-ENOMEM);
 344
 345         evt->buf        = dma_alloc_coherent(dwc->sysdev, length,
 346                         &evt->dma, GFP_KERNEL);
 347         if (!evt->buf)
 348                 return ERR_PTR(-ENOMEM);
 349
 350         return evt;
 351 }
 352
 353 /**
 354  * dwc3_free_event_buffers - frees all allocated event buffers
 355  * @dwc: Pointer to our controller context structure
 356  */
 357 static void dwc3_free_event_buffers(struct dwc3 *dwc)
 358 {
 359         struct dwc3_event_buffer        *evt;
 360
 361         evt = dwc->ev_buf;
 362         if (evt)
 363                 dwc3_free_one_event_buffer(dwc, evt);
 364 }
 365
 366 /**
 367  * dwc3_alloc_event_buffers - Allocates @num event buffers of size @length
 368  * @dwc: pointer to our controller context structure
 369  * @length: size of event buffer
 370  *
 371  * Returns 0 on success otherwise negative errno. In the error case, dwc
 372  * may contain some buffers allocated but not all which were requested.
 373  */
 374 static int dwc3_alloc_event_buffers(struct dwc3 *dwc, unsigned length)
 375 {
 376         struct dwc3_event_buffer *evt;
 377
 378         evt = dwc3_alloc_one_event_buffer(dwc, length);
 379         if (IS_ERR(evt)) {
 380                 dev_err(dwc->dev, "can't allocate event buffer\n");
 381                 return PTR_ERR(evt);
 382         }
 383         dwc->ev_buf = evt;
 384
 385         return 0;
 386 }
 387
 388 /**
 389  * dwc3_event_buffers_setup - setup our allocated event buffers
 390  * @dwc: pointer to our controller context structure
 391  *
 392  * Returns 0 on success otherwise negative errno.
 393  */
 394 int dwc3_event_buffers_setup(struct dwc3 *dwc)
 395 {
 396         struct dwc3_event_buffer        *evt;
 397
 398         evt = dwc->ev_buf;
 399         evt->lpos = 0;
 400         dwc3_writel(dwc->regs, DWC3_GEVNTADRLO(0),
 401                         lower_32_bits(evt->dma));
 402         dwc3_writel(dwc->regs, DWC3_GEVNTADRHI(0),
 403                         upper_32_bits(evt->dma));
 404         dwc3_writel(dwc->regs, DWC3_GEVNTSIZ(0),
 405                         DWC3_GEVNTSIZ_SIZE(evt->length));
 406         dwc3_writel(dwc->regs, DWC3_GEVNTCOUNT(0), 0);
 407
 408         return 0;
 409 }
 410
 411 void dwc3_event_buffers_cleanup(struct dwc3 *dwc)
 412 {
 413         struct dwc3_event_buffer        *evt;
 414
 415         evt = dwc->ev_buf;
 416
 417         evt->lpos = 0;
 418
 419         dwc3_writel(dwc->regs, DWC3_GEVNTADRLO(0), 0);
 420         dwc3_writel(dwc->regs, DWC3_GEVNTADRHI(0), 0);
 421         dwc3_writel(dwc->regs, DWC3_GEVNTSIZ(0), DWC3_GEVNTSIZ_INTMASK
 422                         | DWC3_GEVNTSIZ_SIZE(0));
 423         dwc3_writel(dwc->regs, DWC3_GEVNTCOUNT(0), 0);
 424 }
 425
 426 static int dwc3_alloc_scratch_buffers(struct dwc3 *dwc)
 427 {
 428         if (!dwc->has_hibernation)
 429                 return 0;
 430
 431         if (!dwc->nr_scratch)
 432                 return 0;
 433
 434         dwc->scratchbuf = kmalloc_array(dwc->nr_scratch,
 435                         DWC3_SCRATCHBUF_SIZE, GFP_KERNEL);
 436         if (!dwc->scratchbuf)
 437                 return -ENOMEM;
 438
 439         return 0;
 440 }
 441
 442 static int dwc3_setup_scratch_buffers(struct dwc3 *dwc)
 443 {
 444         dma_addr_t scratch_addr;
 445         u32 param;
 446         int ret;
 447
 448         if (!dwc->has_hibernation)
 449                 return 0;
 450
 451         if (!dwc->nr_scratch)
 452                 return 0;
 453
 454          /* should never fall here */
 455         if (!WARN_ON(dwc->scratchbuf))
 456                 return 0;
 457
 458         scratch_addr = dma_map_single(dwc->sysdev, dwc->scratchbuf,
 459                         dwc->nr_scratch * DWC3_SCRATCHBUF_SIZE,
 460                         DMA_BIDIRECTIONAL);
 461         if (dma_mapping_error(dwc->sysdev, scratch_addr)) {
 462                 dev_err(dwc->sysdev, "failed to map scratch buffer\n");
 463                 ret = -EFAULT;
 464                 goto err0;
 465         }
 466
 467         dwc->scratch_addr = scratch_addr;
 468
 469         param = lower_32_bits(scratch_addr);
 470
 471         ret = dwc3_send_gadget_generic_command(dwc,
 472                         DWC3_DGCMD_SET_SCRATCHPAD_ADDR_LO, param);
 473         if (ret < 0)
 474                 goto err1;
 475
 476         param = upper_32_bits(scratch_addr);
 477
 478         ret = dwc3_send_gadget_generic_command(dwc,
 479                         DWC3_DGCMD_SET_SCRATCHPAD_ADDR_HI, param);
 480         if (ret < 0)
 481                 goto err1;
 482
 483         return 0;
 484
 485 err1:
 486         dma_unmap_single(dwc->sysdev, dwc->scratch_addr, dwc->nr_scratch *
 487                         DWC3_SCRATCHBUF_SIZE, DMA_BIDIRECTIONAL);
 488
 489 err0:
 490         return ret;
 491 }
 492
 493 static void dwc3_free_scratch_buffers(struct dwc3 *dwc)
 494 {
 495         if (!dwc->has_hibernation)
 496                 return;
 497
 498         if (!dwc->nr_scratch)
 499                 return;
 500
 501          /* should never fall here */
 502         if (!WARN_ON(dwc->scratchbuf))
 503                 return;
 504
 505         dma_unmap_single(dwc->sysdev, dwc->scratch_addr, dwc->nr_scratch *
 506                         DWC3_SCRATCHBUF_SIZE, DMA_BIDIRECTIONAL);
 507         kfree(dwc->scratchbuf);
 508 }
 509
 510 static void dwc3_core_num_eps(struct dwc3 *dwc)
 511 {
 512         struct dwc3_hwparams    *parms = &dwc->hwparams;
 513
 514         dwc->num_eps = DWC3_NUM_EPS(parms);
 515 }
 516
 517 static void dwc3_cache_hwparams(struct dwc3 *dwc)
 518 {
 519         struct dwc3_hwparams    *parms = &dwc->hwparams;
 520
 521         parms->hwparams0 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS0);
 522         parms->hwparams1 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS1);
 523         parms->hwparams2 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS2);
 524         parms->hwparams3 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS3);
 525         parms->hwparams4 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS4);
 526         parms->hwparams5 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS5);
 527         parms->hwparams6 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS6);
 528         parms->hwparams7 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS7);
 529         parms->hwparams8 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS8);
 530 }
 531
 532 static int dwc3_core_ulpi_init(struct dwc3 *dwc)
 533 {
 534         int intf;
 535         int ret = 0;
 536
 537         intf = DWC3_GHWPARAMS3_HSPHY_IFC(dwc->hwparams.hwparams3);
 538
 539         if (intf == DWC3_GHWPARAMS3_HSPHY_IFC_ULPI ||
 540             (intf == DWC3_GHWPARAMS3_HSPHY_IFC_UTMI_ULPI &&
 541              dwc->hsphy_interface &&
 542              !strncmp(dwc->hsphy_interface, "ulpi", 4)))
 543                 ret = dwc3_ulpi_init(dwc);
 544
 545         return ret;
 546 }
 547
 548 /**
 549  * dwc3_phy_setup - Configure USB PHY Interface of DWC3 Core
 550  * @dwc: Pointer to our controller context structure
 551  *
 552  * Returns 0 on success. The USB PHY interfaces are configured but not
 553  * initialized. The PHY interfaces and the PHYs get initialized together with
 554  * the core in dwc3_core_init.
 555  */
 556 static int dwc3_phy_setup(struct dwc3 *dwc)
 557 {
 558         u32 reg;
 559
 560         reg = dwc3_readl(dwc->regs, DWC3_GUSB3PIPECTL(0));
 561
 562         /*
 563          * Make sure UX_EXIT_PX is cleared as that causes issues with some
 564          * PHYs. Also, this bit is not supposed to be used in normal operation.
 565          */
 566         reg &= ~DWC3_GUSB3PIPECTL_UX_EXIT_PX;
 567
 568         /*
 569          * Above 1.94a, it is recommended to set DWC3_GUSB3PIPECTL_SUSPHY
 570          * to '0' during coreConsultant configuration. So default value
 571          * will be '0' when the core is reset. Application needs to set it
 572          * to '1' after the core initialization is completed.
 573          */
 574         if (dwc->revision > DWC3_REVISION_194A)
 575                 reg |= DWC3_GUSB3PIPECTL_SUSPHY;
 576
 577         if (dwc->u2ss_inp3_quirk)
 578                 reg |= DWC3_GUSB3PIPECTL_U2SSINP3OK;
 579
 580         if (dwc->dis_rxdet_inp3_quirk)
 581                 reg |= DWC3_GUSB3PIPECTL_DISRXDETINP3;
 582
 583         if (dwc->req_p1p2p3_quirk)
 584                 reg |= DWC3_GUSB3PIPECTL_REQP1P2P3;
 585
 586         if (dwc->del_p1p2p3_quirk)
 587                 reg |= DWC3_GUSB3PIPECTL_DEP1P2P3_EN;
 588
 589         if (dwc->del_phy_power_chg_quirk)
 590                 reg |= DWC3_GUSB3PIPECTL_DEPOCHANGE;
 591
 592         if (dwc->lfps_filter_quirk)
 593                 reg |= DWC3_GUSB3PIPECTL_LFPSFILT;
 594
 595         if (dwc->rx_detect_poll_quirk)
 596                 reg |= DWC3_GUSB3PIPECTL_RX_DETOPOLL;
 597
 598         if (dwc->tx_de_emphasis_quirk)
 599                 reg |= DWC3_GUSB3PIPECTL_TX_DEEPH(dwc->tx_de_emphasis);
 600
 601         if (dwc->dis_u3_susphy_quirk)
 602                 reg &= ~DWC3_GUSB3PIPECTL_SUSPHY;
 603
 604         if (dwc->dis_del_phy_power_chg_quirk)
 605                 reg &= ~DWC3_GUSB3PIPECTL_DEPOCHANGE;
 606
 607         dwc3_writel(dwc->regs, DWC3_GUSB3PIPECTL(0), reg);
 608
 609         reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0));
 610
 611         /* Select the HS PHY interface */
 612         switch (DWC3_GHWPARAMS3_HSPHY_IFC(dwc->hwparams.hwparams3)) {
 613         case DWC3_GHWPARAMS3_HSPHY_IFC_UTMI_ULPI:
 614                 if (dwc->hsphy_interface &&
 615                                 !strncmp(dwc->hsphy_interface, "utmi", 4)) {
 616                         reg &= ~DWC3_GUSB2PHYCFG_ULPI_UTMI;
 617                         break;
 618                 } else if (dwc->hsphy_interface &&
 619                                 !strncmp(dwc->hsphy_interface, "ulpi", 4)) {
 620                         reg |= DWC3_GUSB2PHYCFG_ULPI_UTMI;
 621                         dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg);
 622                 } else {
 623                         /* Relying on default value. */
 624                         if (!(reg & DWC3_GUSB2PHYCFG_ULPI_UTMI))
 625                                 break;
 626                 }
 627                 /* FALLTHROUGH */
 628         case DWC3_GHWPARAMS3_HSPHY_IFC_ULPI:
 629                 /* FALLTHROUGH */
 630         default:
 631                 break;
 632         }
 633
 634         switch (dwc->hsphy_mode) {
 635         case USBPHY_INTERFACE_MODE_UTMI:
 636                 reg &= ~(DWC3_GUSB2PHYCFG_PHYIF_MASK |
 637                        DWC3_GUSB2PHYCFG_USBTRDTIM_MASK);
 638                 reg |= DWC3_GUSB2PHYCFG_PHYIF(UTMI_PHYIF_8_BIT) |
 639                        DWC3_GUSB2PHYCFG_USBTRDTIM(USBTRDTIM_UTMI_8_BIT);
 640                 break;
 641         case USBPHY_INTERFACE_MODE_UTMIW:
 642                 reg &= ~(DWC3_GUSB2PHYCFG_PHYIF_MASK |
 643                        DWC3_GUSB2PHYCFG_USBTRDTIM_MASK);
 644                 reg |= DWC3_GUSB2PHYCFG_PHYIF(UTMI_PHYIF_16_BIT) |
 645                        DWC3_GUSB2PHYCFG_USBTRDTIM(USBTRDTIM_UTMI_16_BIT);
 646                 break;
 647         default:
 648                 break;
 649         }
 650
 651         /*
 652          * Above 1.94a, it is recommended to set DWC3_GUSB2PHYCFG_SUSPHY to
 653          * '0' during coreConsultant configuration. So default value will
 654          * be '0' when the core is reset. Application needs to set it to
 655          * '1' after the core initialization is completed.
 656          */
 657         if (dwc->revision > DWC3_REVISION_194A)
 658                 reg |= DWC3_GUSB2PHYCFG_SUSPHY;
 659
 660         if (dwc->dis_u2_susphy_quirk)
 661                 reg &= ~DWC3_GUSB2PHYCFG_SUSPHY;
 662
 663         if (dwc->dis_enblslpm_quirk)
 664                 reg &= ~DWC3_GUSB2PHYCFG_ENBLSLPM;
 665         else
 666                 reg |= DWC3_GUSB2PHYCFG_ENBLSLPM;
 667
 668         if (dwc->dis_u2_freeclk_exists_quirk)
 669                 reg &= ~DWC3_GUSB2PHYCFG_U2_FREECLK_EXISTS;
 670
 671         dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg);
 672
 673         return 0;
 674 }
 675
 676 static void dwc3_core_exit(struct dwc3 *dwc)
 677 {
 678         dwc3_event_buffers_cleanup(dwc);
 679
 680         usb_phy_shutdown(dwc->usb2_phy);
 681         usb_phy_shutdown(dwc->usb3_phy);
 682         phy_exit(dwc->usb2_generic_phy);
 683         phy_exit(dwc->usb3_generic_phy);
 684
 685         usb_phy_set_suspend(dwc->usb2_phy, 1);
 686         usb_phy_set_suspend(dwc->usb3_phy, 1);
 687         phy_power_off(dwc->usb2_generic_phy);
 688         phy_power_off(dwc->usb3_generic_phy);
 689         clk_bulk_disable(dwc->num_clks, dwc->clks);
 690         clk_bulk_unprepare(dwc->num_clks, dwc->clks);
 691         reset_control_assert(dwc->reset);
 692 }
 693
 694 static bool dwc3_core_is_valid(struct dwc3 *dwc)
 695 {
 696         u32 reg;
 697
 698         reg = dwc3_readl(dwc->regs, DWC3_GSNPSID);
 699
 700         /* This should read as U3 followed by revision number */
 701         if ((reg & DWC3_GSNPSID_MASK) == 0x55330000) {
 702                 /* Detected DWC_usb3 IP */
 703                 dwc->revision = reg;
 704         } else if ((reg & DWC3_GSNPSID_MASK) == 0x33310000) {
 705                 /* Detected DWC_usb31 IP */
 706                 dwc->revision = dwc3_readl(dwc->regs, DWC3_VER_NUMBER);
 707                 dwc->revision |= DWC3_REVISION_IS_DWC31;
 708                 dwc->version_type = dwc3_readl(dwc->regs, DWC3_VER_TYPE);
 709         } else {
 710                 return false;
 711         }
 712
 713         return true;
 714 }
 715
 716 static void dwc3_core_setup_global_control(struct dwc3 *dwc)
 717 {
 718         u32 hwparams4 = dwc->hwparams.hwparams4;
 719         u32 reg;
 720
 721         reg = dwc3_readl(dwc->regs, DWC3_GCTL);
 722         reg &= ~DWC3_GCTL_SCALEDOWN_MASK;
 723
 724         switch (DWC3_GHWPARAMS1_EN_PWROPT(dwc->hwparams.hwparams1)) {
 725         case DWC3_GHWPARAMS1_EN_PWROPT_CLK:
 726                 /**
 727                  * WORKAROUND: DWC3 revisions between 2.10a and 2.50a have an
 728                  * issue which would cause xHCI compliance tests to fail.
 729                  *
 730                  * Because of that we cannot enable clock gating on such
 731                  * configurations.
 732                  *
 733                  * Refers to:
 734                  *
 735                  * STAR#9000588375: Clock Gating, SOF Issues when ref_clk-Based
 736                  * SOF/ITP Mode Used
 737                  */
 738                 if ((dwc->dr_mode == USB_DR_MODE_HOST ||
 739                                 dwc->dr_mode == USB_DR_MODE_OTG) &&
 740                                 (dwc->revision >= DWC3_REVISION_210A &&
 741                                 dwc->revision <= DWC3_REVISION_250A))
 742                         reg |= DWC3_GCTL_DSBLCLKGTNG | DWC3_GCTL_SOFITPSYNC;
 743                 else
 744                         reg &= ~DWC3_GCTL_DSBLCLKGTNG;
 745                 break;
 746         case DWC3_GHWPARAMS1_EN_PWROPT_HIB:
 747                 /* enable hibernation here */
 748                 dwc->nr_scratch = DWC3_GHWPARAMS4_HIBER_SCRATCHBUFS(hwparams4);
 749
 750                 /*
 751                  * REVISIT Enabling this bit so that host-mode hibernation
 752                  * will work. Device-mode hibernation is not yet implemented.
 753                  */
 754                 reg |= DWC3_GCTL_GBLHIBERNATIONEN;
 755                 break;
 756         default:
 757                 /* nothing */
 758                 break;
 759         }
 760
 761         /* check if current dwc3 is on simulation board */
 762         if (dwc->hwparams.hwparams6 & DWC3_GHWPARAMS6_EN_FPGA) {
 763                 dev_info(dwc->dev, "Running with FPGA optimizations\n");
 764                 dwc->is_fpga = true;
 765         }
 766
 767         WARN_ONCE(dwc->disable_scramble_quirk && !dwc->is_fpga,
 768                         "disable_scramble cannot be used on non-FPGA builds\n");
 769
 770         if (dwc->disable_scramble_quirk && dwc->is_fpga)
 771                 reg |= DWC3_GCTL_DISSCRAMBLE;
 772         else
 773                 reg &= ~DWC3_GCTL_DISSCRAMBLE;
 774
 775         if (dwc->u2exit_lfps_quirk)
 776                 reg |= DWC3_GCTL_U2EXIT_LFPS;
 777
 778         /*
 779          * WORKAROUND: DWC3 revisions <1.90a have a bug
 780          * where the device can fail to connect at SuperSpeed
 781          * and falls back to high-speed mode which causes
 782          * the device to enter a Connect/Disconnect loop
 783          */
 784         if (dwc->revision < DWC3_REVISION_190A)
 785                 reg |= DWC3_GCTL_U2RSTECN;
 786
 787         dwc3_writel(dwc->regs, DWC3_GCTL, reg);
 788 }
 789
 790 static int dwc3_core_get_phy(struct dwc3 *dwc);
 791 static int dwc3_core_ulpi_init(struct dwc3 *dwc);
 792
 793 /* set global incr burst type configuration registers */
 794 static void dwc3_set_incr_burst_type(struct dwc3 *dwc)
 795 {
 796         struct device *dev = dwc->dev;
 797         /* incrx_mode : for INCR burst type. */
 798         bool incrx_mode;
 799         /* incrx_size : for size of INCRX burst. */
 800         u32 incrx_size;
 801         u32 *vals;
 802         u32 cfg;
 803         int ntype;
 804         int ret;
 805         int i;
 806
 807         cfg = dwc3_readl(dwc->regs, DWC3_GSBUSCFG0);
 808
 809         /*
 810          * Handle property "snps,incr-burst-type-adjustment".
 811          * Get the number of value from this property:
 812          * result <= 0, means this property is not supported.
 813          * result = 1, means INCRx burst mode supported.
 814          * result > 1, means undefined length burst mode supported.
 815          */
 816         ntype = device_property_read_u32_array(dev,
 817                         "snps,incr-burst-type-adjustment", NULL, 0);
 818         if (ntype <= 0)
 819                 return;
 820
 821         vals = kcalloc(ntype, sizeof(u32), GFP_KERNEL);
 822         if (!vals) {
 823                 dev_err(dev, "Error to get memory\n");
 824                 return;
 825         }
 826
 827         /* Get INCR burst type, and parse it */
 828         ret = device_property_read_u32_array(dev,
 829                         "snps,incr-burst-type-adjustment", vals, ntype);
 830         if (ret) {
 831                 kfree(vals);
 832                 dev_err(dev, "Error to get property\n");
 833                 return;
 834         }
 835
 836         incrx_size = *vals;
 837
 838         if (ntype > 1) {
 839                 /* INCRX (undefined length) burst mode */
 840                 incrx_mode = INCRX_UNDEF_LENGTH_BURST_MODE;
 841                 for (i = 1; i < ntype; i++) {
 842                         if (vals[i] > incrx_size)
 843                                 incrx_size = vals[i];
 844                 }
 845         } else {
 846                 /* INCRX burst mode */
 847                 incrx_mode = INCRX_BURST_MODE;
 848         }
 849
 850         kfree(vals);
 851
 852         /* Enable Undefined Length INCR Burst and Enable INCRx Burst */
 853         cfg &= ~DWC3_GSBUSCFG0_INCRBRST_MASK;
 854         if (incrx_mode)
 855                 cfg |= DWC3_GSBUSCFG0_INCRBRSTENA;
 856         switch (incrx_size) {
 857         case 256:
 858                 cfg |= DWC3_GSBUSCFG0_INCR256BRSTENA;
 859                 break;
 860         case 128:
 861                 cfg |= DWC3_GSBUSCFG0_INCR128BRSTENA;
 862                 break;
 863         case 64:
 864                 cfg |= DWC3_GSBUSCFG0_INCR64BRSTENA;
 865                 break;
 866         case 32:
 867                 cfg |= DWC3_GSBUSCFG0_INCR32BRSTENA;
 868                 break;
 869         case 16:
 870                 cfg |= DWC3_GSBUSCFG0_INCR16BRSTENA;
 871                 break;
 872         case 8:
 873                 cfg |= DWC3_GSBUSCFG0_INCR8BRSTENA;
 874                 break;
 875         case 4:
 876                 cfg |= DWC3_GSBUSCFG0_INCR4BRSTENA;
 877                 break;
 878         case 1:
 879                 break;
 880         default:
 881                 dev_err(dev, "Invalid property\n");
 882                 break;
 883         }
 884
 885         dwc3_writel(dwc->regs, DWC3_GSBUSCFG0, cfg);
 886 }
 887
 888 /**
 889  * dwc3_core_init - Low-level initialization of DWC3 Core
 890  * @dwc: Pointer to our controller context structure
 891  *
 892  * Returns 0 on success otherwise negative errno.
 893  */
 894 static int dwc3_core_init(struct dwc3 *dwc)
 895 {
 896         u32                     reg;
 897         int                     ret;
 898
 899         /*
 900          * Write Linux Version Code to our GUID register so it's easy to figure
 901          * out which kernel version a bug was found.
 902          */
 903         dwc3_writel(dwc->regs, DWC3_GUID, LINUX_VERSION_CODE);
 904
 905         /* Handle USB2.0-only core configuration */
 906         if (DWC3_GHWPARAMS3_SSPHY_IFC(dwc->hwparams.hwparams3) ==
 907                         DWC3_GHWPARAMS3_SSPHY_IFC_DIS) {
 908                 if (dwc->maximum_speed == USB_SPEED_SUPER)
 909                         dwc->maximum_speed = USB_SPEED_HIGH;
 910         }
 911
 912         ret = dwc3_phy_setup(dwc);
 913         if (ret)
 914                 goto err0;
 915
 916         if (!dwc->ulpi_ready) {
 917                 ret = dwc3_core_ulpi_init(dwc);
 918                 if (ret)
 919                         goto err0;
 920                 dwc->ulpi_ready = true;
 921         }
 922
 923         if (!dwc->phys_ready) {
 924                 ret = dwc3_core_get_phy(dwc);
 925                 if (ret)
 926                         goto err0a;
 927                 dwc->phys_ready = true;
 928         }
 929
 930         ret = dwc3_core_soft_reset(dwc);
 931         if (ret)
 932                 goto err0a;
 933
 934         dwc3_core_setup_global_control(dwc);
 935         dwc3_core_num_eps(dwc);
 936
 937         ret = dwc3_setup_scratch_buffers(dwc);
 938         if (ret)
 939                 goto err1;
 940
 941         /* Adjust Frame Length */
 942         dwc3_frame_length_adjustment(dwc);
 943
 944         dwc3_set_incr_burst_type(dwc);
 945
 946         usb_phy_set_suspend(dwc->usb2_phy, 0);
 947         usb_phy_set_suspend(dwc->usb3_phy, 0);
 948         ret = phy_power_on(dwc->usb2_generic_phy);
 949         if (ret < 0)
 950                 goto err2;
 951
 952         ret = phy_power_on(dwc->usb3_generic_phy);
 953         if (ret < 0)
 954                 goto err3;
 955
 956         ret = dwc3_event_buffers_setup(dwc);
 957         if (ret) {
 958                 dev_err(dwc->dev, "failed to setup event buffers\n");
 959                 goto err4;
 960         }
 961
 962         /*
 963          * ENDXFER polling is available on version 3.10a and later of
 964          * the DWC_usb3 controller. It is NOT available in the
 965          * DWC_usb31 controller.
 966          */
 967         if (!dwc3_is_usb31(dwc) && dwc->revision >= DWC3_REVISION_310A) {
 968                 reg = dwc3_readl(dwc->regs, DWC3_GUCTL2);
 969                 reg |= DWC3_GUCTL2_RST_ACTBITLATER;
 970                 dwc3_writel(dwc->regs, DWC3_GUCTL2, reg);
 971         }
 972
 973         if (dwc->revision >= DWC3_REVISION_250A) {
 974                 reg = dwc3_readl(dwc->regs, DWC3_GUCTL1);
 975
 976                 /*
 977                  * Enable hardware control of sending remote wakeup
 978                  * in HS when the device is in the L1 state.
 979                  */
 980                 if (dwc->revision >= DWC3_REVISION_290A)
 981                         reg |= DWC3_GUCTL1_DEV_L1_EXIT_BY_HW;
 982
 983                 if (dwc->dis_tx_ipgap_linecheck_quirk)
 984                         reg |= DWC3_GUCTL1_TX_IPGAP_LINECHECK_DIS;
 985
 986                 dwc3_writel(dwc->regs, DWC3_GUCTL1, reg);
 987         }
 988
 989         if (dwc->dr_mode == USB_DR_MODE_HOST ||
 990             dwc->dr_mode == USB_DR_MODE_OTG) {
 991                 reg = dwc3_readl(dwc->regs, DWC3_GUCTL);
 992
 993                 /*
 994                  * Enable Auto retry Feature to make the controller operating in
 995                  * Host mode on seeing transaction errors(CRC errors or internal
 996                  * overrun scenerios) on IN transfers to reply to the device
 997                  * with a non-terminating retry ACK (i.e, an ACK transcation
 998                  * packet with Retry=1 & Nump != 0)
 999                  */
1000                 reg |= DWC3_GUCTL_HSTINAUTORETRY;
1001
1002                 dwc3_writel(dwc->regs, DWC3_GUCTL, reg);
1003         }
1004
1005         /*
1006          * Must config both number of packets and max burst settings to enable
1007          * RX and/or TX threshold.
1008          */
1009         if (dwc3_is_usb31(dwc) && dwc->dr_mode == USB_DR_MODE_HOST) {
1010                 u8 rx_thr_num = dwc->rx_thr_num_pkt_prd;
1011                 u8 rx_maxburst = dwc->rx_max_burst_prd;
1012                 u8 tx_thr_num = dwc->tx_thr_num_pkt_prd;
1013                 u8 tx_maxburst = dwc->tx_max_burst_prd;
1014
1015                 if (rx_thr_num && rx_maxburst) {
1016                         reg = dwc3_readl(dwc->regs, DWC3_GRXTHRCFG);
1017                         reg |= DWC31_RXTHRNUMPKTSEL_PRD;
1018
1019                         reg &= ~DWC31_RXTHRNUMPKT_PRD(~0);
1020                         reg |= DWC31_RXTHRNUMPKT_PRD(rx_thr_num);
1021
1022                         reg &= ~DWC31_MAXRXBURSTSIZE_PRD(~0);
1023                         reg |= DWC31_MAXRXBURSTSIZE_PRD(rx_maxburst);
1024
1025                         dwc3_writel(dwc->regs, DWC3_GRXTHRCFG, reg);
1026                 }
1027
1028                 if (tx_thr_num && tx_maxburst) {
1029                         reg = dwc3_readl(dwc->regs, DWC3_GTXTHRCFG);
1030                         reg |= DWC31_TXTHRNUMPKTSEL_PRD;
1031
1032                         reg &= ~DWC31_TXTHRNUMPKT_PRD(~0);
1033                         reg |= DWC31_TXTHRNUMPKT_PRD(tx_thr_num);
1034
1035                         reg &= ~DWC31_MAXTXBURSTSIZE_PRD(~0);
1036                         reg |= DWC31_MAXTXBURSTSIZE_PRD(tx_maxburst);
1037
1038                         dwc3_writel(dwc->regs, DWC3_GTXTHRCFG, reg);
1039                 }
1040         }
1041
1042         return 0;
1043
1044 err4:
1045         phy_power_off(dwc->usb3_generic_phy);
1046
1047 err3:
1048         phy_power_off(dwc->usb2_generic_phy);
1049
1050 err2:
1051         usb_phy_set_suspend(dwc->usb2_phy, 1);
1052         usb_phy_set_suspend(dwc->usb3_phy, 1);
1053
1054 err1:
1055         usb_phy_shutdown(dwc->usb2_phy);
1056         usb_phy_shutdown(dwc->usb3_phy);
1057         phy_exit(dwc->usb2_generic_phy);
1058         phy_exit(dwc->usb3_generic_phy);
1059
1060 err0a:
1061         dwc3_ulpi_exit(dwc);
1062
1063 err0:
1064         return ret;
1065 }
1066
1067 static int dwc3_core_get_phy(struct dwc3 *dwc)
1068 {
1069         struct device           *dev = dwc->dev;
1070         struct device_node      *node = dev->of_node;
1071         int ret;
1072
1073         if (node) {
1074                 dwc->usb2_phy = devm_usb_get_phy_by_phandle(dev, "usb-phy", 0);
1075                 dwc->usb3_phy = devm_usb_get_phy_by_phandle(dev, "usb-phy", 1);
1076         } else {
1077                 dwc->usb2_phy = devm_usb_get_phy(dev, USB_PHY_TYPE_USB2);
1078                 dwc->usb3_phy = devm_usb_get_phy(dev, USB_PHY_TYPE_USB3);
1079         }
1080
1081         if (IS_ERR(dwc->usb2_phy)) {
1082                 ret = PTR_ERR(dwc->usb2_phy);
1083                 if (ret == -ENXIO || ret == -ENODEV) {
1084                         dwc->usb2_phy = NULL;
1085                 } else if (ret == -EPROBE_DEFER) {
1086                         return ret;
1087                 } else {
1088                         dev_err(dev, "no usb2 phy configured\n");
1089                         return ret;
1090                 }
1091         }
1092
1093         if (IS_ERR(dwc->usb3_phy)) {
1094                 ret = PTR_ERR(dwc->usb3_phy);
1095                 if (ret == -ENXIO || ret == -ENODEV) {
1096                         dwc->usb3_phy = NULL;
1097                 } else if (ret == -EPROBE_DEFER) {
1098                         return ret;
1099                 } else {
1100                         dev_err(dev, "no usb3 phy configured\n");
1101                         return ret;
1102                 }
1103         }
1104
1105         dwc->usb2_generic_phy = devm_phy_get(dev, "usb2-phy");
1106         if (IS_ERR(dwc->usb2_generic_phy)) {
1107                 ret = PTR_ERR(dwc->usb2_generic_phy);
1108                 if (ret == -ENOSYS || ret == -ENODEV) {
1109                         dwc->usb2_generic_phy = NULL;
1110                 } else if (ret == -EPROBE_DEFER) {
1111                         return ret;
1112                 } else {
1113                         dev_err(dev, "no usb2 phy configured\n");
1114                         return ret;
1115                 }
1116         }
1117
1118         dwc->usb3_generic_phy = devm_phy_get(dev, "usb3-phy");
1119         if (IS_ERR(dwc->usb3_generic_phy)) {
1120                 ret = PTR_ERR(dwc->usb3_generic_phy);
1121                 if (ret == -ENOSYS || ret == -ENODEV) {
1122                         dwc->usb3_generic_phy = NULL;
1123                 } else if (ret == -EPROBE_DEFER) {
1124                         return ret;
1125                 } else {
1126                         dev_err(dev, "no usb3 phy configured\n");
1127                         return ret;
1128                 }
1129         }
1130
1131         return 0;
1132 }
1133
1134 static int dwc3_core_init_mode(struct dwc3 *dwc)
1135 {
1136         struct device *dev = dwc->dev;
1137         int ret;
1138
1139         switch (dwc->dr_mode) {
1140         case USB_DR_MODE_PERIPHERAL:
1141                 dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_DEVICE);
1142
1143                 if (dwc->usb2_phy)
1144                         otg_set_vbus(dwc->usb2_phy->otg, false);
1145                 phy_set_mode(dwc->usb2_generic_phy, PHY_MODE_USB_DEVICE);
1146                 phy_set_mode(dwc->usb3_generic_phy, PHY_MODE_USB_DEVICE);
1147
1148                 ret = dwc3_gadget_init(dwc);
1149                 if (ret) {
1150                         if (ret != -EPROBE_DEFER)
1151                                 dev_err(dev, "failed to initialize gadget\n");
1152                         return ret;
1153                 }
1154                 break;
1155         case USB_DR_MODE_HOST:
1156                 dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_HOST);
1157
1158                 if (dwc->usb2_phy)
1159                         otg_set_vbus(dwc->usb2_phy->otg, true);
1160                 phy_set_mode(dwc->usb2_generic_phy, PHY_MODE_USB_HOST);
1161                 phy_set_mode(dwc->usb3_generic_phy, PHY_MODE_USB_HOST);
1162
1163                 ret = dwc3_host_init(dwc);
1164                 if (ret) {
1165                         if (ret != -EPROBE_DEFER)
1166                                 dev_err(dev, "failed to initialize host\n");
1167                         return ret;
1168                 }
1169                 phy_calibrate(dwc->usb2_generic_phy);
1170                 break;
1171         case USB_DR_MODE_OTG:
1172                 INIT_WORK(&dwc->drd_work, __dwc3_set_mode);
1173                 ret = dwc3_drd_init(dwc);
1174                 if (ret) {
1175                         if (ret != -EPROBE_DEFER)
1176                                 dev_err(dev, "failed to initialize dual-role\n");
1177                         return ret;
1178                 }
1179                 break;
1180         default:
1181                 dev_err(dev, "Unsupported mode of operation %d\n", dwc->dr_mode);
1182                 return -EINVAL;
1183         }
1184
1185         return 0;
1186 }
1187
1188 static void dwc3_core_exit_mode(struct dwc3 *dwc)
1189 {
1190         switch (dwc->dr_mode) {
1191         case USB_DR_MODE_PERIPHERAL:
1192                 dwc3_gadget_exit(dwc);
1193                 break;
1194         case USB_DR_MODE_HOST:
1195                 dwc3_host_exit(dwc);
1196                 break;
1197         case USB_DR_MODE_OTG:
1198                 dwc3_drd_exit(dwc);
1199                 break;
1200         default:
1201                 /* do nothing */
1202                 break;
1203         }
1204 }
1205
1206 static void dwc3_get_properties(struct dwc3 *dwc)
1207 {
1208         struct device           *dev = dwc->dev;
1209         u8                      lpm_nyet_threshold;
1210         u8                      tx_de_emphasis;
1211         u8                      hird_threshold;
1212         u8                      rx_thr_num_pkt_prd;
1213         u8                      rx_max_burst_prd;
1214         u8                      tx_thr_num_pkt_prd;
1215         u8                      tx_max_burst_prd;
1216
1217         /* default to highest possible threshold */
1218         lpm_nyet_threshold = 0xf;
1219
1220         /* default to -3.5dB de-emphasis */
1221         tx_de_emphasis = 1;
1222
1223         /*
1224          * default to assert utmi_sleep_n and use maximum allowed HIRD
1225          * threshold value of 0b1100
1226          */
1227         hird_threshold = 12;
1228
1229         dwc->maximum_speed = usb_get_maximum_speed(dev);
1230         dwc->dr_mode = usb_get_dr_mode(dev);
1231         dwc->hsphy_mode = of_usb_get_phy_mode(dev->of_node);
1232
1233         dwc->sysdev_is_parent = device_property_read_bool(dev,
1234                                 "linux,sysdev_is_parent");
1235         if (dwc->sysdev_is_parent)
1236                 dwc->sysdev = dwc->dev->parent;
1237         else
1238                 dwc->sysdev = dwc->dev;
1239
1240         dwc->has_lpm_erratum = device_property_read_bool(dev,
1241                                 "snps,has-lpm-erratum");
1242         device_property_read_u8(dev, "snps,lpm-nyet-threshold",
1243                                 &lpm_nyet_threshold);
1244         dwc->is_utmi_l1_suspend = device_property_read_bool(dev,
1245                                 "snps,is-utmi-l1-suspend");
1246         device_property_read_u8(dev, "snps,hird-threshold",
1247                                 &hird_threshold);
1248         dwc->dis_start_transfer_quirk = device_property_read_bool(dev,
1249                                 "snps,dis-start-transfer-quirk");
1250         dwc->usb3_lpm_capable = device_property_read_bool(dev,
1251                                 "snps,usb3_lpm_capable");
1252         dwc->usb2_lpm_disable = device_property_read_bool(dev,
1253                                 "snps,usb2-lpm-disable");
1254         device_property_read_u8(dev, "snps,rx-thr-num-pkt-prd",
1255                                 &rx_thr_num_pkt_prd);
1256         device_property_read_u8(dev, "snps,rx-max-burst-prd",
1257                                 &rx_max_burst_prd);
1258         device_property_read_u8(dev, "snps,tx-thr-num-pkt-prd",
1259                                 &tx_thr_num_pkt_prd);
1260         device_property_read_u8(dev, "snps,tx-max-burst-prd",
1261                                 &tx_max_burst_prd);
1262
1263         dwc->disable_scramble_quirk = device_property_read_bool(dev,
1264                                 "snps,disable_scramble_quirk");
1265         dwc->u2exit_lfps_quirk = device_property_read_bool(dev,
1266                                 "snps,u2exit_lfps_quirk");
1267         dwc->u2ss_inp3_quirk = device_property_read_bool(dev,
1268                                 "snps,u2ss_inp3_quirk");
1269         dwc->req_p1p2p3_quirk = device_property_read_bool(dev,
1270                                 "snps,req_p1p2p3_quirk");
1271         dwc->del_p1p2p3_quirk = device_property_read_bool(dev,
1272                                 "snps,del_p1p2p3_quirk");
1273         dwc->del_phy_power_chg_quirk = device_property_read_bool(dev,
1274                                 "snps,del_phy_power_chg_quirk");
1275         dwc->lfps_filter_quirk = device_property_read_bool(dev,
1276                                 "snps,lfps_filter_quirk");
1277         dwc->rx_detect_poll_quirk = device_property_read_bool(dev,
1278                                 "snps,rx_detect_poll_quirk");
1279         dwc->dis_u3_susphy_quirk = device_property_read_bool(dev,
1280                                 "snps,dis_u3_susphy_quirk");
1281         dwc->dis_u2_susphy_quirk = device_property_read_bool(dev,
1282                                 "snps,dis_u2_susphy_quirk");
1283         dwc->dis_enblslpm_quirk = device_property_read_bool(dev,
1284                                 "snps,dis_enblslpm_quirk");
1285         dwc->dis_rxdet_inp3_quirk = device_property_read_bool(dev,
1286                                 "snps,dis_rxdet_inp3_quirk");
1287         dwc->dis_u2_freeclk_exists_quirk = device_property_read_bool(dev,
1288                                 "snps,dis-u2-freeclk-exists-quirk");
1289         dwc->dis_del_phy_power_chg_quirk = device_property_read_bool(dev,
1290                                 "snps,dis-del-phy-power-chg-quirk");
1291         dwc->dis_tx_ipgap_linecheck_quirk = device_property_read_bool(dev,
1292                                 "snps,dis-tx-ipgap-linecheck-quirk");
1293
1294         dwc->tx_de_emphasis_quirk = device_property_read_bool(dev,
1295                                 "snps,tx_de_emphasis_quirk");
1296         device_property_read_u8(dev, "snps,tx_de_emphasis",
1297                                 &tx_de_emphasis);
1298         device_property_read_string(dev, "snps,hsphy_interface",
1299                                     &dwc->hsphy_interface);
1300         device_property_read_u32(dev, "snps,quirk-frame-length-adjustment",
1301                                  &dwc->fladj);
1302
1303         dwc->dis_metastability_quirk = device_property_read_bool(dev,
1304                                 "snps,dis_metastability_quirk");
1305
1306         dwc->lpm_nyet_threshold = lpm_nyet_threshold;
1307         dwc->tx_de_emphasis = tx_de_emphasis;
1308
1309         dwc->hird_threshold = hird_threshold
1310                 | (dwc->is_utmi_l1_suspend << 4);
1311
1312         dwc->rx_thr_num_pkt_prd = rx_thr_num_pkt_prd;
1313         dwc->rx_max_burst_prd = rx_max_burst_prd;
1314
1315         dwc->tx_thr_num_pkt_prd = tx_thr_num_pkt_prd;
1316         dwc->tx_max_burst_prd = tx_max_burst_prd;
1317
1318         dwc->imod_interval = 0;
1319 }
1320
1321 /* check whether the core supports IMOD */
1322 bool dwc3_has_imod(struct dwc3 *dwc)
1323 {
1324         return ((dwc3_is_usb3(dwc) &&
1325                  dwc->revision >= DWC3_REVISION_300A) ||
1326                 (dwc3_is_usb31(dwc) &&
1327                  dwc->revision >= DWC3_USB31_REVISION_120A));
1328 }
1329
1330 static void dwc3_check_params(struct dwc3 *dwc)
1331 {
1332         struct device *dev = dwc->dev;
1333
1334         /* Check for proper value of imod_interval */
1335         if (dwc->imod_interval && !dwc3_has_imod(dwc)) {
1336                 dev_warn(dwc->dev, "Interrupt moderation not supported\n");
1337                 dwc->imod_interval = 0;
1338         }
1339
1340         /*
1341          * Workaround for STAR 9000961433 which affects only version
1342          * 3.00a of the DWC_usb3 core. This prevents the controller
1343          * interrupt from being masked while handling events. IMOD
1344          * allows us to work around this issue. Enable it for the
1345          * affected version.
1346          */
1347         if (!dwc->imod_interval &&
1348             (dwc->revision == DWC3_REVISION_300A))
1349                 dwc->imod_interval = 1;
1350
1351         /* Check the maximum_speed parameter */
1352         switch (dwc->maximum_speed) {
1353         case USB_SPEED_LOW:
1354         case USB_SPEED_FULL:
1355         case USB_SPEED_HIGH:
1356         case USB_SPEED_SUPER:
1357         case USB_SPEED_SUPER_PLUS:
1358                 break;
1359         default:
1360                 dev_err(dev, "invalid maximum_speed parameter %d\n",
1361                         dwc->maximum_speed);
1362                 /* fall through */
1363         case USB_SPEED_UNKNOWN:
1364                 /* default to superspeed */
1365                 dwc->maximum_speed = USB_SPEED_SUPER;
1366
1367                 /*
1368                  * default to superspeed plus if we are capable.
1369                  */
1370                 if (dwc3_is_usb31(dwc) &&
1371                     (DWC3_GHWPARAMS3_SSPHY_IFC(dwc->hwparams.hwparams3) ==
1372                      DWC3_GHWPARAMS3_SSPHY_IFC_GEN2))
1373                         dwc->maximum_speed = USB_SPEED_SUPER_PLUS;
1374
1375                 break;
1376         }
1377 }
1378
1379 static int dwc3_probe(struct platform_device *pdev)
1380 {
1381         struct device           *dev = &pdev->dev;
1382         struct resource         *res, dwc_res;
1383         struct dwc3             *dwc;
1384
1385         int                     ret;
1386
1387         void __iomem            *regs;
1388
1389         dwc = devm_kzalloc(dev, sizeof(*dwc), GFP_KERNEL);
1390         if (!dwc)
1391                 return -ENOMEM;
1392
1393         dwc->clks = devm_kmemdup(dev, dwc3_core_clks, sizeof(dwc3_core_clks),
1394                                  GFP_KERNEL);
1395         if (!dwc->clks)
1396                 return -ENOMEM;
1397
1398         dwc->dev = dev;
1399
1400         res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
1401         if (!res) {
1402                 dev_err(dev, "missing memory resource\n");
1403                 return -ENODEV;
1404         }
1405
1406         dwc->xhci_resources[0].start = res->start;
1407         dwc->xhci_resources[0].end = dwc->xhci_resources[0].start +
1408                                         DWC3_XHCI_REGS_END;
1409         dwc->xhci_resources[0].flags = res->flags;
1410         dwc->xhci_resources[0].name = res->name;
1411
1412         /*
1413          * Request memory region but exclude xHCI regs,
1414          * since it will be requested by the xhci-plat driver.
1415          */
1416         dwc_res = *res;
1417         dwc_res.start += DWC3_GLOBALS_REGS_START;
1418
1419         regs = devm_ioremap_resource(dev, &dwc_res);
1420         if (IS_ERR(regs))
1421                 return PTR_ERR(regs);
1422
1423         dwc->regs       = regs;
1424         dwc->regs_size  = resource_size(&dwc_res);
1425
1426         if (!dwc3_core_is_valid(dwc)) {
1427                 dev_err(dwc->dev, "this is not a DesignWare USB3 DRD Core\n");
1428                 return -ENODEV;
1429         }
1430
1431         dwc3_get_properties(dwc);
1432
1433         dwc->reset = devm_reset_control_get_optional_shared(dev, NULL);
1434         if (IS_ERR(dwc->reset))
1435                 return PTR_ERR(dwc->reset);
1436
1437         if (dev->of_node) {
1438                 dwc->num_clks = ARRAY_SIZE(dwc3_core_clks);
1439
1440                 ret = clk_bulk_get(dev, dwc->num_clks, dwc->clks);
1441                 if (ret == -EPROBE_DEFER)
1442                         return ret;
1443                 /*
1444                  * Clocks are optional, but new DT platforms should support all
1445                  * clocks as required by the DT-binding.
1446                  */
1447                 if (ret)
1448                         dwc->num_clks = 0;
1449         }
1450
1451         ret = reset_control_deassert(dwc->reset);
1452         if (ret)
1453                 goto put_clks;
1454
1455         ret = clk_bulk_prepare(dwc->num_clks, dwc->clks);
1456         if (ret)
1457                 goto assert_reset;
1458
1459         ret = clk_bulk_enable(dwc->num_clks, dwc->clks);
1460         if (ret)
1461                 goto unprepare_clks;
1462
1463         platform_set_drvdata(pdev, dwc);
1464         dwc3_cache_hwparams(dwc);
1465
1466         spin_lock_init(&dwc->lock);
1467
1468         pm_runtime_set_active(dev);
1469         pm_runtime_use_autosuspend(dev);
1470         pm_runtime_set_autosuspend_delay(dev, DWC3_DEFAULT_AUTOSUSPEND_DELAY);
1471         pm_runtime_enable(dev);
1472         ret = pm_runtime_get_sync(dev);
1473         if (ret < 0)
1474                 goto err1;
1475
1476         pm_runtime_forbid(dev);
1477
1478         ret = dwc3_alloc_event_buffers(dwc, DWC3_EVENT_BUFFERS_SIZE);
1479         if (ret) {
1480                 dev_err(dwc->dev, "failed to allocate event buffers\n");
1481                 ret = -ENOMEM;
1482                 goto err2;
1483         }
1484
1485         ret = dwc3_get_dr_mode(dwc);
1486         if (ret)
1487                 goto err3;
1488
1489         ret = dwc3_alloc_scratch_buffers(dwc);
1490         if (ret)
1491                 goto err3;
1492
1493         ret = dwc3_core_init(dwc);
1494         if (ret) {
1495                 if (ret != -EPROBE_DEFER)
1496                         dev_err(dev, "failed to initialize core: %d\n", ret);
1497                 goto err4;
1498         }
1499
1500         dwc3_check_params(dwc);
1501
1502         ret = dwc3_core_init_mode(dwc);
1503         if (ret)
1504                 goto err5;
1505
1506         dwc3_debugfs_init(dwc);
1507         pm_runtime_put(dev);
1508
1509         return 0;
1510
1511 err5:
1512         dwc3_event_buffers_cleanup(dwc);
1513         dwc3_ulpi_exit(dwc);
1514
1515 err4:
1516         dwc3_free_scratch_buffers(dwc);
1517
1518 err3:
1519         dwc3_free_event_buffers(dwc);
1520
1521 err2:
1522         pm_runtime_allow(&pdev->dev);
1523
1524 err1:
1525         pm_runtime_put_sync(&pdev->dev);
1526         pm_runtime_disable(&pdev->dev);
1527
1528         clk_bulk_disable(dwc->num_clks, dwc->clks);
1529 unprepare_clks:
1530         clk_bulk_unprepare(dwc->num_clks, dwc->clks);
1531 assert_reset:
1532         reset_control_assert(dwc->reset);
1533 put_clks:
1534         clk_bulk_put(dwc->num_clks, dwc->clks);
1535
1536         return ret;
1537 }
1538
1539 static int dwc3_remove(struct platform_device *pdev)
1540 {
1541         struct dwc3     *dwc = platform_get_drvdata(pdev);
1542
1543         pm_runtime_get_sync(&pdev->dev);
1544
1545         dwc3_debugfs_exit(dwc);
1546         dwc3_core_exit_mode(dwc);
1547
1548         dwc3_core_exit(dwc);
1549         dwc3_ulpi_exit(dwc);
1550
1551         pm_runtime_put_sync(&pdev->dev);
1552         pm_runtime_allow(&pdev->dev);
1553         pm_runtime_disable(&pdev->dev);
1554
1555         dwc3_free_event_buffers(dwc);
1556         dwc3_free_scratch_buffers(dwc);
1557         clk_bulk_put(dwc->num_clks, dwc->clks);
1558
1559         return 0;
1560 }
1561
1562 #ifdef CONFIG_PM
1563 static int dwc3_core_init_for_resume(struct dwc3 *dwc)
1564 {
1565         int ret;
1566
1567         ret = reset_control_deassert(dwc->reset);
1568         if (ret)
1569                 return ret;
1570
1571         ret = clk_bulk_prepare(dwc->num_clks, dwc->clks);
1572         if (ret)
1573                 goto assert_reset;
1574
1575         ret = clk_bulk_enable(dwc->num_clks, dwc->clks);
1576         if (ret)
1577                 goto unprepare_clks;
1578
1579         ret = dwc3_core_init(dwc);
1580         if (ret)
1581                 goto disable_clks;
1582
1583         return 0;
1584
1585 disable_clks:
1586         clk_bulk_disable(dwc->num_clks, dwc->clks);
1587 unprepare_clks:
1588         clk_bulk_unprepare(dwc->num_clks, dwc->clks);
1589 assert_reset:
1590         reset_control_assert(dwc->reset);
1591
1592         return ret;
1593 }
1594
1595 static int dwc3_suspend_common(struct dwc3 *dwc, pm_message_t msg)
1596 {
1597         unsigned long   flags;
1598         u32 reg;
1599
1600         switch (dwc->current_dr_role) {
1601         case DWC3_GCTL_PRTCAP_DEVICE:
1602                 spin_lock_irqsave(&dwc->lock, flags);
1603                 dwc3_gadget_suspend(dwc);
1604                 spin_unlock_irqrestore(&dwc->lock, flags);
1605                 synchronize_irq(dwc->irq_gadget);
1606                 dwc3_core_exit(dwc);
1607                 break;
1608         case DWC3_GCTL_PRTCAP_HOST:
1609                 if (!PMSG_IS_AUTO(msg)) {
1610                         dwc3_core_exit(dwc);
1611                         break;
1612                 }
1613
1614                 /* Let controller to suspend HSPHY before PHY driver suspends */
1615                 if (dwc->dis_u2_susphy_quirk ||
1616                     dwc->dis_enblslpm_quirk) {
1617                         reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0));
1618                         reg |=  DWC3_GUSB2PHYCFG_ENBLSLPM |
1619                                 DWC3_GUSB2PHYCFG_SUSPHY;
1620                         dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg);
1621
1622                         /* Give some time for USB2 PHY to suspend */
1623                         usleep_range(5000, 6000);
1624                 }
1625
1626                 phy_pm_runtime_put_sync(dwc->usb2_generic_phy);
1627                 phy_pm_runtime_put_sync(dwc->usb3_generic_phy);
1628                 break;
1629         case DWC3_GCTL_PRTCAP_OTG:
1630                 /* do nothing during runtime_suspend */
1631                 if (PMSG_IS_AUTO(msg))
1632                         break;
1633
1634                 if (dwc->current_otg_role == DWC3_OTG_ROLE_DEVICE) {
1635                         spin_lock_irqsave(&dwc->lock, flags);
1636                         dwc3_gadget_suspend(dwc);
1637                         spin_unlock_irqrestore(&dwc->lock, flags);
1638                         synchronize_irq(dwc->irq_gadget);
1639                 }
1640
1641                 dwc3_otg_exit(dwc);
1642                 dwc3_core_exit(dwc);
1643                 break;
1644         default:
1645                 /* do nothing */
1646                 break;
1647         }
1648
1649         return 0;
1650 }
1651
1652 static int dwc3_resume_common(struct dwc3 *dwc, pm_message_t msg)
1653 {
1654         unsigned long   flags;
1655         int             ret;
1656         u32             reg;
1657
1658         switch (dwc->current_dr_role) {
1659         case DWC3_GCTL_PRTCAP_DEVICE:
1660                 ret = dwc3_core_init_for_resume(dwc);
1661                 if (ret)
1662                         return ret;
1663
1664                 dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_DEVICE);
1665                 spin_lock_irqsave(&dwc->lock, flags);
1666                 dwc3_gadget_resume(dwc);
1667                 spin_unlock_irqrestore(&dwc->lock, flags);
1668                 break;
1669         case DWC3_GCTL_PRTCAP_HOST:
1670                 if (!PMSG_IS_AUTO(msg)) {
1671                         ret = dwc3_core_init_for_resume(dwc);
1672                         if (ret)
1673                                 return ret;
1674                         dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_HOST);
1675                         break;
1676                 }
1677                 /* Restore GUSB2PHYCFG bits that were modified in suspend */
1678                 reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0));
1679                 if (dwc->dis_u2_susphy_quirk)
1680                         reg &= ~DWC3_GUSB2PHYCFG_SUSPHY;
1681
1682                 if (dwc->dis_enblslpm_quirk)
1683                         reg &= ~DWC3_GUSB2PHYCFG_ENBLSLPM;
1684
1685                 dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg);
1686
1687                 phy_pm_runtime_get_sync(dwc->usb2_generic_phy);
1688                 phy_pm_runtime_get_sync(dwc->usb3_generic_phy);
1689                 break;
1690         case DWC3_GCTL_PRTCAP_OTG:
1691                 /* nothing to do on runtime_resume */
1692                 if (PMSG_IS_AUTO(msg))
1693                         break;
1694
1695                 ret = dwc3_core_init(dwc);
1696                 if (ret)
1697                         return ret;
1698
1699                 dwc3_set_prtcap(dwc, dwc->current_dr_role);
1700
1701                 dwc3_otg_init(dwc);
1702                 if (dwc->current_otg_role == DWC3_OTG_ROLE_HOST) {
1703                         dwc3_otg_host_init(dwc);
1704                 } else if (dwc->current_otg_role == DWC3_OTG_ROLE_DEVICE) {
1705                         spin_lock_irqsave(&dwc->lock, flags);
1706                         dwc3_gadget_resume(dwc);
1707                         spin_unlock_irqrestore(&dwc->lock, flags);
1708                 }
1709
1710                 break;
1711         default:
1712                 /* do nothing */
1713                 break;
1714         }
1715
1716         return 0;
1717 }
1718
1719 static int dwc3_runtime_checks(struct dwc3 *dwc)
1720 {
1721         switch (dwc->current_dr_role) {
1722         case DWC3_GCTL_PRTCAP_DEVICE:
1723                 if (dwc->connected)
1724                         return -EBUSY;
1725                 break;
1726         case DWC3_GCTL_PRTCAP_HOST:
1727         default:
1728                 /* do nothing */
1729                 break;
1730         }
1731
1732         return 0;
1733 }
1734
1735 static int dwc3_runtime_suspend(struct device *dev)
1736 {
1737         struct dwc3     *dwc = dev_get_drvdata(dev);
1738         int             ret;
1739
1740         if (dwc3_runtime_checks(dwc))
1741                 return -EBUSY;
1742
1743         ret = dwc3_suspend_common(dwc, PMSG_AUTO_SUSPEND);
1744         if (ret)
1745                 return ret;
1746
1747         device_init_wakeup(dev, true);
1748
1749         return 0;
1750 }
1751
1752 static int dwc3_runtime_resume(struct device *dev)
1753 {
1754         struct dwc3     *dwc = dev_get_drvdata(dev);
1755         int             ret;
1756
1757         device_init_wakeup(dev, false);
1758
1759         ret = dwc3_resume_common(dwc, PMSG_AUTO_RESUME);
1760         if (ret)
1761                 return ret;
1762
1763         switch (dwc->current_dr_role) {
1764         case DWC3_GCTL_PRTCAP_DEVICE:
1765                 dwc3_gadget_process_pending_events(dwc);
1766                 break;
1767         case DWC3_GCTL_PRTCAP_HOST:
1768         default:
1769                 /* do nothing */
1770                 break;
1771         }
1772
1773         pm_runtime_mark_last_busy(dev);
1774
1775         return 0;
1776 }
1777
1778 static int dwc3_runtime_idle(struct device *dev)
1779 {
1780         struct dwc3     *dwc = dev_get_drvdata(dev);
1781
1782         switch (dwc->current_dr_role) {
1783         case DWC3_GCTL_PRTCAP_DEVICE:
1784                 if (dwc3_runtime_checks(dwc))
1785                         return -EBUSY;
1786                 break;
1787         case DWC3_GCTL_PRTCAP_HOST:
1788         default:
1789                 /* do nothing */
1790                 break;
1791         }
1792
1793         pm_runtime_mark_last_busy(dev);
1794         pm_runtime_autosuspend(dev);
1795
1796         return 0;
1797 }
1798 #endif /* CONFIG_PM */
1799
1800 #ifdef CONFIG_PM_SLEEP
1801 static int dwc3_suspend(struct device *dev)
1802 {
1803         struct dwc3     *dwc = dev_get_drvdata(dev);
1804         int             ret;
1805
1806         ret = dwc3_suspend_common(dwc, PMSG_SUSPEND);
1807         if (ret)
1808                 return ret;
1809
1810         pinctrl_pm_select_sleep_state(dev);
1811
1812         return 0;
1813 }
1814
1815 static int dwc3_resume(struct device *dev)
1816 {
1817         struct dwc3     *dwc = dev_get_drvdata(dev);
1818         int             ret;
1819
1820         pinctrl_pm_select_default_state(dev);
1821
1822         ret = dwc3_resume_common(dwc, PMSG_RESUME);
1823         if (ret)
1824                 return ret;
1825
1826         pm_runtime_disable(dev);
1827         pm_runtime_set_active(dev);
1828         pm_runtime_enable(dev);
1829
1830         return 0;
1831 }
1832 #endif /* CONFIG_PM_SLEEP */
1833
1834 static const struct dev_pm_ops dwc3_dev_pm_ops = {
1835         SET_SYSTEM_SLEEP_PM_OPS(dwc3_suspend, dwc3_resume)
1836         SET_RUNTIME_PM_OPS(dwc3_runtime_suspend, dwc3_runtime_resume,
1837                         dwc3_runtime_idle)
1838 };
1839
1840 #ifdef CONFIG_OF
1841 static const struct of_device_id of_dwc3_match[] = {
1842         {
1843                 .compatible = "snps,dwc3"
1844         },
1845         {
1846                 .compatible = "synopsys,dwc3"
1847         },
1848         { },
1849 };
1850 MODULE_DEVICE_TABLE(of, of_dwc3_match);
1851 #endif
1852
1853 #ifdef CONFIG_ACPI
1854
1855 #define ACPI_ID_INTEL_BSW       "808622B7"
1856
1857 static const struct acpi_device_id dwc3_acpi_match[] = {
1858         { ACPI_ID_INTEL_BSW, 0 },
1859         { },
1860 };
1861 MODULE_DEVICE_TABLE(acpi, dwc3_acpi_match);
1862 #endif
1863
1864 static struct platform_driver dwc3_driver = {
1865         .probe          = dwc3_probe,
1866         .remove         = dwc3_remove,
1867         .driver         = {
1868                 .name   = "dwc3",
1869                 .of_match_table = of_match_ptr(of_dwc3_match),
1870                 .acpi_match_table = ACPI_PTR(dwc3_acpi_match),
1871                 .pm     = &dwc3_dev_pm_ops,
1872         },
1873 };
1874
1875 module_platform_driver(dwc3_driver);
1876
1877 MODULE_ALIAS("platform:dwc3");
1878 MODULE_AUTHOR("Felipe Balbi <[email protected]>");
1879 MODULE_LICENSE("GPL v2");
1880 MODULE_DESCRIPTION("DesignWare USB3 DRD Controller Driver");