drivers/ssb/driver_chipcommon.c

   1 /*
   2  * Sonics Silicon Backplane
   3  * Broadcom ChipCommon core driver
   4  *
   5  * Copyright 2005, Broadcom Corporation
   6  * Copyright 2006, 2007, Michael Buesch <[email protected]>
   7  *
   8  * Licensed under the GNU/GPL. See COPYING for details.
   9  */
  10
  11 #include <linux/ssb/ssb.h>
  12 #include <linux/ssb/ssb_regs.h>
  13 #include <linux/pci.h>
  14
  15 #include "ssb_private.h"
  16
  17
  18 /* Clock sources */
  19 enum ssb_clksrc {
  20         /* PCI clock */
  21         SSB_CHIPCO_CLKSRC_PCI,
  22         /* Crystal slow clock oscillator */
  23         SSB_CHIPCO_CLKSRC_XTALOS,
  24         /* Low power oscillator */
  25         SSB_CHIPCO_CLKSRC_LOPWROS,
  26 };
  27
  28
  29 static inline u32 chipco_write32_masked(struct ssb_chipcommon *cc, u16 offset,
  30                                         u32 mask, u32 value)
  31 {
  32         value &= mask;
  33         value |= chipco_read32(cc, offset) & ~mask;
  34         chipco_write32(cc, offset, value);
  35
  36         return value;
  37 }
  38
  39 void ssb_chipco_set_clockmode(struct ssb_chipcommon *cc,
  40                               enum ssb_clkmode mode)
  41 {
  42         struct ssb_device *ccdev = cc->dev;
  43         struct ssb_bus *bus;
  44         u32 tmp;
  45
  46         if (!ccdev)
  47                 return;
  48         bus = ccdev->bus;
  49         /* chipcommon cores prior to rev6 don't support dynamic clock control */
  50         if (ccdev->id.revision < 6)
  51                 return;
  52         /* chipcommon cores rev10 are a whole new ball game */
  53         if (ccdev->id.revision >= 10)
  54                 return;
  55         if (!(cc->capabilities & SSB_CHIPCO_CAP_PCTL))
  56                 return;
  57
  58         switch (mode) {
  59         case SSB_CLKMODE_SLOW:
  60                 tmp = chipco_read32(cc, SSB_CHIPCO_SLOWCLKCTL);
  61                 tmp |= SSB_CHIPCO_SLOWCLKCTL_FSLOW;
  62                 chipco_write32(cc, SSB_CHIPCO_SLOWCLKCTL, tmp);
  63                 break;
  64         case SSB_CLKMODE_FAST:
  65                 ssb_pci_xtal(bus, SSB_GPIO_XTAL, 1); /* Force crystal on */
  66                 tmp = chipco_read32(cc, SSB_CHIPCO_SLOWCLKCTL);
  67                 tmp &= ~SSB_CHIPCO_SLOWCLKCTL_FSLOW;
  68                 tmp |= SSB_CHIPCO_SLOWCLKCTL_IPLL;
  69                 chipco_write32(cc, SSB_CHIPCO_SLOWCLKCTL, tmp);
  70                 break;
  71         case SSB_CLKMODE_DYNAMIC:
  72                 tmp = chipco_read32(cc, SSB_CHIPCO_SLOWCLKCTL);
  73                 tmp &= ~SSB_CHIPCO_SLOWCLKCTL_FSLOW;
  74                 tmp &= ~SSB_CHIPCO_SLOWCLKCTL_IPLL;
  75                 tmp &= ~SSB_CHIPCO_SLOWCLKCTL_ENXTAL;
  76                 if ((tmp & SSB_CHIPCO_SLOWCLKCTL_SRC) != SSB_CHIPCO_SLOWCLKCTL_SRC_XTAL)
  77                         tmp |= SSB_CHIPCO_SLOWCLKCTL_ENXTAL;
  78                 chipco_write32(cc, SSB_CHIPCO_SLOWCLKCTL, tmp);
  79
  80                 /* for dynamic control, we have to release our xtal_pu "force on" */
  81                 if (tmp & SSB_CHIPCO_SLOWCLKCTL_ENXTAL)
  82                         ssb_pci_xtal(bus, SSB_GPIO_XTAL, 0);
  83                 break;
  84         default:
  85                 SSB_WARN_ON(1);
  86         }
  87 }
  88
  89 /* Get the Slow Clock Source */
  90 static enum ssb_clksrc chipco_pctl_get_slowclksrc(struct ssb_chipcommon *cc)
  91 {
  92         struct ssb_bus *bus = cc->dev->bus;
  93         u32 uninitialized_var(tmp);
  94
  95         if (cc->dev->id.revision < 6) {
  96                 if (bus->bustype == SSB_BUSTYPE_SSB ||
  97                     bus->bustype == SSB_BUSTYPE_PCMCIA)
  98                         return SSB_CHIPCO_CLKSRC_XTALOS;
  99                 if (bus->bustype == SSB_BUSTYPE_PCI) {
 100                         pci_read_config_dword(bus->host_pci, SSB_GPIO_OUT, &tmp);
 101                         if (tmp & 0x10)
 102                                 return SSB_CHIPCO_CLKSRC_PCI;
 103                         return SSB_CHIPCO_CLKSRC_XTALOS;
 104                 }
 105         }
 106         if (cc->dev->id.revision < 10) {
 107                 tmp = chipco_read32(cc, SSB_CHIPCO_SLOWCLKCTL);
 108                 tmp &= 0x7;
 109                 if (tmp == 0)
 110                         return SSB_CHIPCO_CLKSRC_LOPWROS;
 111                 if (tmp == 1)
 112                         return SSB_CHIPCO_CLKSRC_XTALOS;
 113                 if (tmp == 2)
 114                         return SSB_CHIPCO_CLKSRC_PCI;
 115         }
 116
 117         return SSB_CHIPCO_CLKSRC_XTALOS;
 118 }
 119
 120 /* Get maximum or minimum (depending on get_max flag) slowclock frequency. */
 121 static int chipco_pctl_clockfreqlimit(struct ssb_chipcommon *cc, int get_max)
 122 {
 123         int uninitialized_var(limit);
 124         enum ssb_clksrc clocksrc;
 125         int divisor = 1;
 126         u32 tmp;
 127
 128         clocksrc = chipco_pctl_get_slowclksrc(cc);
 129         if (cc->dev->id.revision < 6) {
 130                 switch (clocksrc) {
 131                 case SSB_CHIPCO_CLKSRC_PCI:
 132                         divisor = 64;
 133                         break;
 134                 case SSB_CHIPCO_CLKSRC_XTALOS:
 135                         divisor = 32;
 136                         break;
 137                 default:
 138                         SSB_WARN_ON(1);
 139                 }
 140         } else if (cc->dev->id.revision < 10) {
 141                 switch (clocksrc) {
 142                 case SSB_CHIPCO_CLKSRC_LOPWROS:
 143                         break;
 144                 case SSB_CHIPCO_CLKSRC_XTALOS:
 145                 case SSB_CHIPCO_CLKSRC_PCI:
 146                         tmp = chipco_read32(cc, SSB_CHIPCO_SLOWCLKCTL);
 147                         divisor = (tmp >> 16) + 1;
 148                         divisor *= 4;
 149                         break;
 150                 }
 151         } else {
 152                 tmp = chipco_read32(cc, SSB_CHIPCO_SYSCLKCTL);
 153                 divisor = (tmp >> 16) + 1;
 154                 divisor *= 4;
 155         }
 156
 157         switch (clocksrc) {
 158         case SSB_CHIPCO_CLKSRC_LOPWROS:
 159                 if (get_max)
 160                         limit = 43000;
 161                 else
 162                         limit = 25000;
 163                 break;
 164         case SSB_CHIPCO_CLKSRC_XTALOS:
 165                 if (get_max)
 166                         limit = 20200000;
 167                 else
 168                         limit = 19800000;
 169                 break;
 170         case SSB_CHIPCO_CLKSRC_PCI:
 171                 if (get_max)
 172                         limit = 34000000;
 173                 else
 174                         limit = 25000000;
 175                 break;
 176         }
 177         limit /= divisor;
 178
 179         return limit;
 180 }
 181
 182 static void chipco_powercontrol_init(struct ssb_chipcommon *cc)
 183 {
 184         struct ssb_bus *bus = cc->dev->bus;
 185
 186         if (bus->chip_id == 0x4321) {
 187                 if (bus->chip_rev == 0)
 188                         chipco_write32(cc, SSB_CHIPCO_CHIPCTL, 0x3A4);
 189                 else if (bus->chip_rev == 1)
 190                         chipco_write32(cc, SSB_CHIPCO_CHIPCTL, 0xA4);
 191         }
 192
 193         if (!(cc->capabilities & SSB_CHIPCO_CAP_PCTL))
 194                 return;
 195
 196         if (cc->dev->id.revision >= 10) {
 197                 /* Set Idle Power clock rate to 1Mhz */
 198                 chipco_write32(cc, SSB_CHIPCO_SYSCLKCTL,
 199                                (chipco_read32(cc, SSB_CHIPCO_SYSCLKCTL) &
 200                                 0x0000FFFF) | 0x00040000);
 201         } else {
 202                 int maxfreq;
 203
 204                 maxfreq = chipco_pctl_clockfreqlimit(cc, 1);
 205                 chipco_write32(cc, SSB_CHIPCO_PLLONDELAY,
 206                                (maxfreq * 150 + 999999) / 1000000);
 207                 chipco_write32(cc, SSB_CHIPCO_FREFSELDELAY,
 208                                (maxfreq * 15 + 999999) / 1000000);
 209         }
 210 }
 211
 212 /* http://bcm-v4.sipsolutions.net/802.11/PmuFastPwrupDelay */
 213 static u16 pmu_fast_powerup_delay(struct ssb_chipcommon *cc)
 214 {
 215         struct ssb_bus *bus = cc->dev->bus;
 216
 217         switch (bus->chip_id) {
 218         case 0x4312:
 219         case 0x4322:
 220         case 0x4328:
 221                 return 7000;
 222         case 0x4325:
 223                 /* TODO: */
 224         default:
 225                 return 15000;
 226         }
 227 }
 228
 229 /* http://bcm-v4.sipsolutions.net/802.11/ClkctlFastPwrupDelay */
 230 static void calc_fast_powerup_delay(struct ssb_chipcommon *cc)
 231 {
 232         struct ssb_bus *bus = cc->dev->bus;
 233         int minfreq;
 234         unsigned int tmp;
 235         u32 pll_on_delay;
 236
 237         if (bus->bustype != SSB_BUSTYPE_PCI)
 238                 return;
 239
 240         if (cc->capabilities & SSB_CHIPCO_CAP_PMU) {
 241                 cc->fast_pwrup_delay = pmu_fast_powerup_delay(cc);
 242                 return;
 243         }
 244
 245         if (!(cc->capabilities & SSB_CHIPCO_CAP_PCTL))
 246                 return;
 247
 248         minfreq = chipco_pctl_clockfreqlimit(cc, 0);
 249         pll_on_delay = chipco_read32(cc, SSB_CHIPCO_PLLONDELAY);
 250         tmp = (((pll_on_delay + 2) * 1000000) + (minfreq - 1)) / minfreq;
 251         SSB_WARN_ON(tmp & ~0xFFFF);
 252
 253         cc->fast_pwrup_delay = tmp;
 254 }
 255
 256 void ssb_chipcommon_init(struct ssb_chipcommon *cc)
 257 {
 258         if (!cc->dev)
 259                 return; /* We don't have a ChipCommon */
 260         if (cc->dev->id.revision >= 11)
 261                 cc->status = chipco_read32(cc, SSB_CHIPCO_CHIPSTAT);
 262         ssb_dprintk(KERN_INFO PFX "chipcommon status is 0x%x\n", cc->status);
 263         ssb_pmu_init(cc);
 264         chipco_powercontrol_init(cc);
 265         ssb_chipco_set_clockmode(cc, SSB_CLKMODE_FAST);
 266         calc_fast_powerup_delay(cc);
 267 }
 268
 269 void ssb_chipco_suspend(struct ssb_chipcommon *cc)
 270 {
 271         if (!cc->dev)
 272                 return;
 273         ssb_chipco_set_clockmode(cc, SSB_CLKMODE_SLOW);
 274 }
 275
 276 void ssb_chipco_resume(struct ssb_chipcommon *cc)
 277 {
 278         if (!cc->dev)
 279                 return;
 280         chipco_powercontrol_init(cc);
 281         ssb_chipco_set_clockmode(cc, SSB_CLKMODE_FAST);
 282 }
 283
 284 /* Get the processor clock */
 285 void ssb_chipco_get_clockcpu(struct ssb_chipcommon *cc,
 286                              u32 *plltype, u32 *n, u32 *m)
 287 {
 288         *n = chipco_read32(cc, SSB_CHIPCO_CLOCK_N);
 289         *plltype = (cc->capabilities & SSB_CHIPCO_CAP_PLLT);
 290         switch (*plltype) {
 291         case SSB_PLLTYPE_2:
 292         case SSB_PLLTYPE_4:
 293         case SSB_PLLTYPE_6:
 294         case SSB_PLLTYPE_7:
 295                 *m = chipco_read32(cc, SSB_CHIPCO_CLOCK_MIPS);
 296                 break;
 297         case SSB_PLLTYPE_3:
 298                 /* 5350 uses m2 to control mips */
 299                 *m = chipco_read32(cc, SSB_CHIPCO_CLOCK_M2);
 300                 break;
 301         default:
 302                 *m = chipco_read32(cc, SSB_CHIPCO_CLOCK_SB);
 303                 break;
 304         }
 305 }
 306
 307 /* Get the bus clock */
 308 void ssb_chipco_get_clockcontrol(struct ssb_chipcommon *cc,
 309                                  u32 *plltype, u32 *n, u32 *m)
 310 {
 311         *n = chipco_read32(cc, SSB_CHIPCO_CLOCK_N);
 312         *plltype = (cc->capabilities & SSB_CHIPCO_CAP_PLLT);
 313         switch (*plltype) {
 314         case SSB_PLLTYPE_6: /* 100/200 or 120/240 only */
 315                 *m = chipco_read32(cc, SSB_CHIPCO_CLOCK_MIPS);
 316                 break;
 317         case SSB_PLLTYPE_3: /* 25Mhz, 2 dividers */
 318                 if (cc->dev->bus->chip_id != 0x5365) {
 319                         *m = chipco_read32(cc, SSB_CHIPCO_CLOCK_M2);
 320                         break;
 321                 }
 322                 /* Fallthough */
 323         default:
 324                 *m = chipco_read32(cc, SSB_CHIPCO_CLOCK_SB);
 325         }
 326 }
 327
 328 void ssb_chipco_timing_init(struct ssb_chipcommon *cc,
 329                             unsigned long ns)
 330 {
 331         struct ssb_device *dev = cc->dev;
 332         struct ssb_bus *bus = dev->bus;
 333         u32 tmp;
 334
 335         /* set register for external IO to control LED. */
 336         chipco_write32(cc, SSB_CHIPCO_PROG_CFG, 0x11);
 337         tmp = DIV_ROUND_UP(10, ns) << SSB_PROG_WCNT_3_SHIFT;            /* Waitcount-3 = 10ns */
 338         tmp |= DIV_ROUND_UP(40, ns) << SSB_PROG_WCNT_1_SHIFT;   /* Waitcount-1 = 40ns */
 339         tmp |= DIV_ROUND_UP(240, ns);                           /* Waitcount-0 = 240ns */
 340         chipco_write32(cc, SSB_CHIPCO_PROG_WAITCNT, tmp);       /* 0x01020a0c for a 100Mhz clock */
 341
 342         /* Set timing for the flash */
 343         tmp = DIV_ROUND_UP(10, ns) << SSB_FLASH_WCNT_3_SHIFT;   /* Waitcount-3 = 10nS */
 344         tmp |= DIV_ROUND_UP(10, ns) << SSB_FLASH_WCNT_1_SHIFT;  /* Waitcount-1 = 10nS */
 345         tmp |= DIV_ROUND_UP(120, ns);                           /* Waitcount-0 = 120nS */
 346         if ((bus->chip_id == 0x5365) ||
 347             (dev->id.revision < 9))
 348                 chipco_write32(cc, SSB_CHIPCO_FLASH_WAITCNT, tmp);
 349         if ((bus->chip_id == 0x5365) ||
 350             (dev->id.revision < 9) ||
 351             ((bus->chip_id == 0x5350) && (bus->chip_rev == 0)))
 352                 chipco_write32(cc, SSB_CHIPCO_PCMCIA_MEMWAIT, tmp);
 353
 354         if (bus->chip_id == 0x5350) {
 355                 /* Enable EXTIF */
 356                 tmp = DIV_ROUND_UP(10, ns) << SSB_PROG_WCNT_3_SHIFT;      /* Waitcount-3 = 10ns */
 357                 tmp |= DIV_ROUND_UP(20, ns) << SSB_PROG_WCNT_2_SHIFT;  /* Waitcount-2 = 20ns */
 358                 tmp |= DIV_ROUND_UP(100, ns) << SSB_PROG_WCNT_1_SHIFT; /* Waitcount-1 = 100ns */
 359                 tmp |= DIV_ROUND_UP(120, ns);                     /* Waitcount-0 = 120ns */
 360                 chipco_write32(cc, SSB_CHIPCO_PROG_WAITCNT, tmp); /* 0x01020a0c for a 100Mhz clock */
 361         }
 362 }
 363
 364 /* Set chip watchdog reset timer to fire in 'ticks' backplane cycles */
 365 void ssb_chipco_watchdog_timer_set(struct ssb_chipcommon *cc, u32 ticks)
 366 {
 367         /* instant NMI */
 368         chipco_write32(cc, SSB_CHIPCO_WATCHDOG, ticks);
 369 }
 370
 371 void ssb_chipco_irq_mask(struct ssb_chipcommon *cc, u32 mask, u32 value)
 372 {
 373         chipco_write32_masked(cc, SSB_CHIPCO_IRQMASK, mask, value);
 374 }
 375
 376 u32 ssb_chipco_irq_status(struct ssb_chipcommon *cc, u32 mask)
 377 {
 378         return chipco_read32(cc, SSB_CHIPCO_IRQSTAT) & mask;
 379 }
 380
 381 u32 ssb_chipco_gpio_in(struct ssb_chipcommon *cc, u32 mask)
 382 {
 383         return chipco_read32(cc, SSB_CHIPCO_GPIOIN) & mask;
 384 }
 385
 386 u32 ssb_chipco_gpio_out(struct ssb_chipcommon *cc, u32 mask, u32 value)
 387 {
 388         return chipco_write32_masked(cc, SSB_CHIPCO_GPIOOUT, mask, value);
 389 }
 390
 391 u32 ssb_chipco_gpio_outen(struct ssb_chipcommon *cc, u32 mask, u32 value)
 392 {
 393         return chipco_write32_masked(cc, SSB_CHIPCO_GPIOOUTEN, mask, value);
 394 }
 395
 396 u32 ssb_chipco_gpio_control(struct ssb_chipcommon *cc, u32 mask, u32 value)
 397 {
 398         return chipco_write32_masked(cc, SSB_CHIPCO_GPIOCTL, mask, value);
 399 }
 400 EXPORT_SYMBOL(ssb_chipco_gpio_control);
 401
 402 u32 ssb_chipco_gpio_intmask(struct ssb_chipcommon *cc, u32 mask, u32 value)
 403 {
 404         return chipco_write32_masked(cc, SSB_CHIPCO_GPIOIRQ, mask, value);
 405 }
 406
 407 u32 ssb_chipco_gpio_polarity(struct ssb_chipcommon *cc, u32 mask, u32 value)
 408 {
 409         return chipco_write32_masked(cc, SSB_CHIPCO_GPIOPOL, mask, value);
 410 }
 411
 412 #ifdef CONFIG_SSB_SERIAL
 413 int ssb_chipco_serial_init(struct ssb_chipcommon *cc,
 414                            struct ssb_serial_port *ports)
 415 {
 416         struct ssb_bus *bus = cc->dev->bus;
 417         int nr_ports = 0;
 418         u32 plltype;
 419         unsigned int irq;
 420         u32 baud_base, div;
 421         u32 i, n;
 422         unsigned int ccrev = cc->dev->id.revision;
 423
 424         plltype = (cc->capabilities & SSB_CHIPCO_CAP_PLLT);
 425         irq = ssb_mips_irq(cc->dev);
 426
 427         if (plltype == SSB_PLLTYPE_1) {
 428                 /* PLL clock */
 429                 baud_base = ssb_calc_clock_rate(plltype,
 430                                                 chipco_read32(cc, SSB_CHIPCO_CLOCK_N),
 431                                                 chipco_read32(cc, SSB_CHIPCO_CLOCK_M2));
 432                 div = 1;
 433         } else {
 434                 if (ccrev == 20) {
 435                         /* BCM5354 uses constant 25MHz clock */
 436                         baud_base = 25000000;
 437                         div = 48;
 438                         /* Set the override bit so we don't divide it */
 439                         chipco_write32(cc, SSB_CHIPCO_CORECTL,
 440                                        chipco_read32(cc, SSB_CHIPCO_CORECTL)
 441                                        | SSB_CHIPCO_CORECTL_UARTCLK0);
 442                 } else if ((ccrev >= 11) && (ccrev != 15)) {
 443                         /* Fixed ALP clock */
 444                         baud_base = 20000000;
 445                         if (cc->capabilities & SSB_CHIPCO_CAP_PMU) {
 446                                 /* FIXME: baud_base is different for devices with a PMU */
 447                                 SSB_WARN_ON(1);
 448                         }
 449                         div = 1;
 450                         if (ccrev >= 21) {
 451                                 /* Turn off UART clock before switching clocksource. */
 452                                 chipco_write32(cc, SSB_CHIPCO_CORECTL,
 453                                                chipco_read32(cc, SSB_CHIPCO_CORECTL)
 454                                                & ~SSB_CHIPCO_CORECTL_UARTCLKEN);
 455                         }
 456                         /* Set the override bit so we don't divide it */
 457                         chipco_write32(cc, SSB_CHIPCO_CORECTL,
 458                                        chipco_read32(cc, SSB_CHIPCO_CORECTL)
 459                                        | SSB_CHIPCO_CORECTL_UARTCLK0);
 460                         if (ccrev >= 21) {
 461                                 /* Re-enable the UART clock. */
 462                                 chipco_write32(cc, SSB_CHIPCO_CORECTL,
 463                                                chipco_read32(cc, SSB_CHIPCO_CORECTL)
 464                                                | SSB_CHIPCO_CORECTL_UARTCLKEN);
 465                         }
 466                 } else if (ccrev >= 3) {
 467                         /* Internal backplane clock */
 468                         baud_base = ssb_clockspeed(bus);
 469                         div = chipco_read32(cc, SSB_CHIPCO_CLKDIV)
 470                               & SSB_CHIPCO_CLKDIV_UART;
 471                 } else {
 472                         /* Fixed internal backplane clock */
 473                         baud_base = 88000000;
 474                         div = 48;
 475                 }
 476
 477                 /* Clock source depends on strapping if UartClkOverride is unset */
 478                 if ((ccrev > 0) &&
 479                     !(chipco_read32(cc, SSB_CHIPCO_CORECTL) & SSB_CHIPCO_CORECTL_UARTCLK0)) {
 480                         if ((cc->capabilities & SSB_CHIPCO_CAP_UARTCLK) ==
 481                             SSB_CHIPCO_CAP_UARTCLK_INT) {
 482                                 /* Internal divided backplane clock */
 483                                 baud_base /= div;
 484                         } else {
 485                                 /* Assume external clock of 1.8432 MHz */
 486                                 baud_base = 1843200;
 487                         }
 488                 }
 489         }
 490
 491         /* Determine the registers of the UARTs */
 492         n = (cc->capabilities & SSB_CHIPCO_CAP_NRUART);
 493         for (i = 0; i < n; i++) {
 494                 void __iomem *cc_mmio;
 495                 void __iomem *uart_regs;
 496
 497                 cc_mmio = cc->dev->bus->mmio + (cc->dev->core_index * SSB_CORE_SIZE);
 498                 uart_regs = cc_mmio + SSB_CHIPCO_UART0_DATA;
 499                 /* Offset changed at after rev 0 */
 500                 if (ccrev == 0)
 501                         uart_regs += (i * 8);
 502                 else
 503                         uart_regs += (i * 256);
 504
 505                 nr_ports++;
 506                 ports[i].regs = uart_regs;
 507                 ports[i].irq = irq;
 508                 ports[i].baud_base = baud_base;
 509                 ports[i].reg_shift = 0;
 510         }
 511
 512         return nr_ports;
 513 }
 514 #endif /* CONFIG_SSB_SERIAL */