1 // SPDX-License-Identifier: GPL-2.0
3 * Driver for Future Domain TMC-16x0 and TMC-3260 SCSI host adapters
4 * Copyright 2019 Ondrej Zary
9 * Future Domain BIOS versions supported for autodetect:
10 * 2.0, 3.0, 3.2, 3.4 (1.0), 3.5 (2.0), 3.6, 3.61
12 * TMC-1800, TMC-18C50, TMC-18C30, TMC-36C70
14 * Future Domain TMC-1650, TMC-1660, TMC-1670, TMC-1680, TMC-1610M/MER/MEX
15 * Future Domain TMC-3260 (PCI)
16 * Quantum ISA-200S, ISA-250MG
17 * Adaptec AHA-2920A (PCI) [BUT *NOT* AHA-2920C -- use aic7xxx instead]
22 * The Adaptec AHA-2920C has an Adaptec AIC-7850 chip on it.
23 * Use the aic7xxx driver for this board.
25 * The Adaptec AHA-2920A has a Future Domain chip on it, so this is the right
26 * driver for that card. Unfortunately, the boxes will probably just say
27 * "2920", so you'll have to look on the card for a Future Domain logo, or a
28 * letter after the 2920.
30 * If you have a TMC-8xx or TMC-9xx board, then this is not the driver for
35 * This is the Linux low-level SCSI driver for Future Domain TMC-1660/1680
36 * TMC-1650/1670, and TMC-3260 SCSI host adapters. The 1650 and 1670 have a
37 * 25-pin external connector, whereas the 1660 and 1680 have a SCSI-2 50-pin
38 * high-density external connector. The 1670 and 1680 have floppy disk
39 * controllers built in. The TMC-3260 is a PCI bus card.
41 * Future Domain's older boards are based on the TMC-1800 chip, and this
42 * driver was originally written for a TMC-1680 board with the TMC-1800 chip.
43 * More recently, boards are being produced with the TMC-18C50 and TMC-18C30
46 * Please note that the drive ordering that Future Domain implemented in BIOS
47 * versions 3.4 and 3.5 is the opposite of the order (currently) used by the
48 * rest of the SCSI industry.
53 * "TMC-1800 SCSI Chip Specification (FDC-1800T)", Future Domain Corporation,
56 * "Technical Reference Manual: 18C50 SCSI Host Adapter Chip", Future Domain
57 * Corporation, January 1992.
59 * "LXT SCSI Products: Specifications and OEM Technical Manual (Revision
60 * B/September 1991)", Maxtor Corporation, 1991.
62 * "7213S product Manual (Revision P3)", Maxtor Corporation, 1992.
64 * "Draft Proposed American National Standard: Small Computer System
65 * Interface - 2 (SCSI-2)", Global Engineering Documents. (X3T9.2/86-109,
66 * revision 10h, October 17, 1991)
71 * Private communication, Tuong Le (Future Domain Engineering department),
72 * 1994. (Disk geometry computations for Future Domain BIOS version 3.4, and
73 * TMC-18C30 detection.)
75 * Hogan, Thom. The Programmer's PC Sourcebook. Microsoft Press, 1988. Page
76 * 60 (2.39: Disk Partition Table Layout).
78 * "18C30 Technical Reference Manual", Future Domain Corporation, 1993, page
82 #include <linux/module.h>
83 #include <linux/interrupt.h>
84 #include <linux/delay.h>
85 #include <linux/pci.h>
86 #include <linux/workqueue.h>
87 #include <scsi/scsicam.h>
88 #include <scsi/scsi_cmnd.h>
89 #include <scsi/scsi_device.h>
90 #include <scsi/scsi_host.h>
94 * FIFO_COUNT: The host adapter has an 8K cache (host adapters based on the
95 * 18C30 chip have a 2k cache). When this many 512 byte blocks are filled by
96 * the SCSI device, an interrupt will be raised. Therefore, this could be as
97 * low as 0, or as high as 16. Note, however, that values which are too high
98 * or too low seem to prevent any interrupts from occurring, and thereby lock
101 #define FIFO_COUNT 2 /* Number of 512 byte blocks before INTR */
102 #define PARITY_MASK ACTL_PAREN /* Parity enabled, 0 = disabled */
113 struct scsi_cmnd *cur_cmd;
115 struct work_struct work;
118 static inline void fdomain_make_bus_idle(struct fdomain *fd)
120 outb(0, fd->base + REG_BCTL);
121 outb(0, fd->base + REG_MCTL);
122 if (fd->chip == tmc18c50 || fd->chip == tmc18c30)
123 /* Clear forced intr. */
124 outb(ACTL_RESET | ACTL_CLRFIRQ | PARITY_MASK,
125 fd->base + REG_ACTL);
127 outb(ACTL_RESET | PARITY_MASK, fd->base + REG_ACTL);
130 static enum chip_type fdomain_identify(int port)
132 u16 id = inb(port + REG_ID_LSB) | inb(port + REG_ID_MSB) << 8;
137 case 0x60e9: /* 18c50 or 18c30 */
143 /* Try to toggle 32-bit mode. This only works on an 18c30 chip. */
144 outb(CFG2_32BIT, port + REG_CFG2);
145 if ((inb(port + REG_CFG2) & CFG2_32BIT)) {
146 outb(0, port + REG_CFG2);
147 if ((inb(port + REG_CFG2) & CFG2_32BIT) == 0)
150 /* If that failed, we are an 18c50. */
154 static int fdomain_test_loopback(int base)
158 for (i = 0; i < 255; i++) {
159 outb(i, base + REG_LOOPBACK);
160 if (inb(base + REG_LOOPBACK) != i)
167 static void fdomain_reset(int base)
169 outb(1, base + REG_BCTL);
171 outb(0, base + REG_BCTL);
173 outb(0, base + REG_MCTL);
174 outb(PARITY_MASK, base + REG_ACTL);
177 static int fdomain_select(struct Scsi_Host *sh, int target)
180 unsigned long timeout;
181 struct fdomain *fd = shost_priv(sh);
183 outb(BCTL_BUSEN | BCTL_SEL, fd->base + REG_BCTL);
184 outb(BIT(sh->this_id) | BIT(target), fd->base + REG_SCSI_DATA_NOACK);
186 /* Stop arbitration and enable parity */
187 outb(PARITY_MASK, fd->base + REG_ACTL);
189 timeout = 350; /* 350 msec */
192 status = inb(fd->base + REG_BSTAT);
193 if (status & BSTAT_BSY) {
194 /* Enable SCSI Bus */
195 /* (on error, should make bus idle with 0) */
196 outb(BCTL_BUSEN, fd->base + REG_BCTL);
201 fdomain_make_bus_idle(fd);
205 static void fdomain_finish_cmd(struct fdomain *fd, int result)
207 outb(0, fd->base + REG_ICTL);
208 fdomain_make_bus_idle(fd);
209 fd->cur_cmd->result = result;
210 fd->cur_cmd->scsi_done(fd->cur_cmd);
214 static void fdomain_read_data(struct scsi_cmnd *cmd)
216 struct fdomain *fd = shost_priv(cmd->device->host);
217 unsigned char *virt, *ptr;
220 while ((len = inw(fd->base + REG_FIFO_COUNT)) > 0) {
221 offset = scsi_bufflen(cmd) - scsi_get_resid(cmd);
222 virt = scsi_kmap_atomic_sg(scsi_sglist(cmd), scsi_sg_count(cmd),
226 *ptr++ = inb(fd->base + REG_FIFO);
228 insw(fd->base + REG_FIFO, ptr, len >> 1);
229 scsi_set_resid(cmd, scsi_get_resid(cmd) - len);
230 scsi_kunmap_atomic_sg(virt);
234 static void fdomain_write_data(struct scsi_cmnd *cmd)
236 struct fdomain *fd = shost_priv(cmd->device->host);
237 /* 8k FIFO for pre-tmc18c30 chips, 2k FIFO for tmc18c30 */
238 int FIFO_Size = fd->chip == tmc18c30 ? 0x800 : 0x2000;
239 unsigned char *virt, *ptr;
242 while ((len = FIFO_Size - inw(fd->base + REG_FIFO_COUNT)) > 512) {
243 offset = scsi_bufflen(cmd) - scsi_get_resid(cmd);
244 if (len + offset > scsi_bufflen(cmd)) {
245 len = scsi_bufflen(cmd) - offset;
249 virt = scsi_kmap_atomic_sg(scsi_sglist(cmd), scsi_sg_count(cmd),
253 outb(*ptr++, fd->base + REG_FIFO);
255 outsw(fd->base + REG_FIFO, ptr, len >> 1);
256 scsi_set_resid(cmd, scsi_get_resid(cmd) - len);
257 scsi_kunmap_atomic_sg(virt);
261 static void fdomain_work(struct work_struct *work)
263 struct fdomain *fd = container_of(work, struct fdomain, work);
264 struct Scsi_Host *sh = container_of((void *)fd, struct Scsi_Host,
266 struct scsi_cmnd *cmd = fd->cur_cmd;
271 spin_lock_irqsave(sh->host_lock, flags);
273 if (cmd->SCp.phase & in_arbitration) {
274 status = inb(fd->base + REG_ASTAT);
275 if (!(status & ASTAT_ARB)) {
276 fdomain_finish_cmd(fd, DID_BUS_BUSY << 16);
279 cmd->SCp.phase = in_selection;
281 outb(ICTL_SEL | FIFO_COUNT, fd->base + REG_ICTL);
282 outb(BCTL_BUSEN | BCTL_SEL, fd->base + REG_BCTL);
283 outb(BIT(cmd->device->host->this_id) | BIT(scmd_id(cmd)),
284 fd->base + REG_SCSI_DATA_NOACK);
285 /* Stop arbitration and enable parity */
286 outb(ACTL_IRQEN | PARITY_MASK, fd->base + REG_ACTL);
288 } else if (cmd->SCp.phase & in_selection) {
289 status = inb(fd->base + REG_BSTAT);
290 if (!(status & BSTAT_BSY)) {
291 /* Try again, for slow devices */
292 if (fdomain_select(cmd->device->host, scmd_id(cmd))) {
293 fdomain_finish_cmd(fd, DID_NO_CONNECT << 16);
296 /* Stop arbitration and enable parity */
297 outb(ACTL_IRQEN | PARITY_MASK, fd->base + REG_ACTL);
299 cmd->SCp.phase = in_other;
300 outb(ICTL_FIFO | ICTL_REQ | FIFO_COUNT, fd->base + REG_ICTL);
301 outb(BCTL_BUSEN, fd->base + REG_BCTL);
305 /* cur_cmd->SCp.phase == in_other: this is the body of the routine */
306 status = inb(fd->base + REG_BSTAT);
308 if (status & BSTAT_REQ) {
309 switch (status & 0x0e) {
310 case BSTAT_CMD: /* COMMAND OUT */
311 outb(cmd->cmnd[cmd->SCp.sent_command++],
312 fd->base + REG_SCSI_DATA);
314 case 0: /* DATA OUT -- tmc18c50/tmc18c30 only */
315 if (fd->chip != tmc1800 && !cmd->SCp.have_data_in) {
316 cmd->SCp.have_data_in = -1;
317 outb(ACTL_IRQEN | ACTL_FIFOWR | ACTL_FIFOEN |
318 PARITY_MASK, fd->base + REG_ACTL);
321 case BSTAT_IO: /* DATA IN -- tmc18c50/tmc18c30 only */
322 if (fd->chip != tmc1800 && !cmd->SCp.have_data_in) {
323 cmd->SCp.have_data_in = 1;
324 outb(ACTL_IRQEN | ACTL_FIFOEN | PARITY_MASK,
325 fd->base + REG_ACTL);
328 case BSTAT_CMD | BSTAT_IO: /* STATUS IN */
329 cmd->SCp.Status = inb(fd->base + REG_SCSI_DATA);
331 case BSTAT_MSG | BSTAT_CMD: /* MESSAGE OUT */
332 outb(MESSAGE_REJECT, fd->base + REG_SCSI_DATA);
334 case BSTAT_MSG | BSTAT_IO | BSTAT_CMD: /* MESSAGE IN */
335 cmd->SCp.Message = inb(fd->base + REG_SCSI_DATA);
336 if (!cmd->SCp.Message)
342 if (fd->chip == tmc1800 && !cmd->SCp.have_data_in &&
343 cmd->SCp.sent_command >= cmd->cmd_len) {
344 if (cmd->sc_data_direction == DMA_TO_DEVICE) {
345 cmd->SCp.have_data_in = -1;
346 outb(ACTL_IRQEN | ACTL_FIFOWR | ACTL_FIFOEN |
347 PARITY_MASK, fd->base + REG_ACTL);
349 cmd->SCp.have_data_in = 1;
350 outb(ACTL_IRQEN | ACTL_FIFOEN | PARITY_MASK,
351 fd->base + REG_ACTL);
355 if (cmd->SCp.have_data_in == -1) /* DATA OUT */
356 fdomain_write_data(cmd);
358 if (cmd->SCp.have_data_in == 1) /* DATA IN */
359 fdomain_read_data(cmd);
362 fdomain_finish_cmd(fd, (cmd->SCp.Status & 0xff) |
363 ((cmd->SCp.Message & 0xff) << 8) |
366 if (cmd->SCp.phase & disconnect) {
367 outb(ICTL_FIFO | ICTL_SEL | ICTL_REQ | FIFO_COUNT,
368 fd->base + REG_ICTL);
369 outb(0, fd->base + REG_BCTL);
371 outb(ICTL_FIFO | ICTL_REQ | FIFO_COUNT,
372 fd->base + REG_ICTL);
375 spin_unlock_irqrestore(sh->host_lock, flags);
378 static irqreturn_t fdomain_irq(int irq, void *dev_id)
380 struct fdomain *fd = dev_id;
383 if ((inb(fd->base + REG_ASTAT) & ASTAT_IRQ) == 0)
386 outb(0, fd->base + REG_ICTL);
388 /* We usually have one spurious interrupt after each command. */
389 if (!fd->cur_cmd) /* Spurious interrupt */
392 schedule_work(&fd->work);
397 static int fdomain_queue(struct Scsi_Host *sh, struct scsi_cmnd *cmd)
399 struct fdomain *fd = shost_priv(cmd->device->host);
403 cmd->SCp.Message = 0;
404 cmd->SCp.have_data_in = 0;
405 cmd->SCp.sent_command = 0;
406 cmd->SCp.phase = in_arbitration;
407 scsi_set_resid(cmd, scsi_bufflen(cmd));
409 spin_lock_irqsave(sh->host_lock, flags);
413 fdomain_make_bus_idle(fd);
415 /* Start arbitration */
416 outb(0, fd->base + REG_ICTL);
417 outb(0, fd->base + REG_BCTL); /* Disable data drivers */
419 outb(BIT(cmd->device->host->this_id), fd->base + REG_SCSI_DATA_NOACK);
420 outb(ICTL_ARB, fd->base + REG_ICTL);
421 /* Start arbitration */
422 outb(ACTL_ARB | ACTL_IRQEN | PARITY_MASK, fd->base + REG_ACTL);
424 spin_unlock_irqrestore(sh->host_lock, flags);
429 static int fdomain_abort(struct scsi_cmnd *cmd)
431 struct Scsi_Host *sh = cmd->device->host;
432 struct fdomain *fd = shost_priv(sh);
438 spin_lock_irqsave(sh->host_lock, flags);
440 fdomain_make_bus_idle(fd);
441 fd->cur_cmd->SCp.phase |= aborted;
442 fd->cur_cmd->result = DID_ABORT << 16;
444 /* Aborts are not done well. . . */
445 fdomain_finish_cmd(fd, DID_ABORT << 16);
446 spin_unlock_irqrestore(sh->host_lock, flags);
450 static int fdomain_host_reset(struct scsi_cmnd *cmd)
452 struct Scsi_Host *sh = cmd->device->host;
453 struct fdomain *fd = shost_priv(sh);
456 spin_lock_irqsave(sh->host_lock, flags);
457 fdomain_reset(fd->base);
458 spin_unlock_irqrestore(sh->host_lock, flags);
462 static int fdomain_biosparam(struct scsi_device *sdev,
463 struct block_device *bdev, sector_t capacity,
466 unsigned char *p = scsi_bios_ptable(bdev);
468 if (p && p[65] == 0xaa && p[64] == 0x55 /* Partition table valid */
469 && p[4]) { /* Partition type */
470 geom[0] = p[5] + 1; /* heads */
471 geom[1] = p[6] & 0x3f; /* sectors */
473 if (capacity >= 0x7e0000) {
474 geom[0] = 255; /* heads */
475 geom[1] = 63; /* sectors */
476 } else if (capacity >= 0x200000) {
477 geom[0] = 128; /* heads */
478 geom[1] = 63; /* sectors */
480 geom[0] = 64; /* heads */
481 geom[1] = 32; /* sectors */
484 geom[2] = sector_div(capacity, geom[0] * geom[1]);
490 static struct scsi_host_template fdomain_template = {
491 .module = THIS_MODULE,
492 .name = "Future Domain TMC-16x0",
493 .proc_name = "fdomain",
494 .queuecommand = fdomain_queue,
495 .eh_abort_handler = fdomain_abort,
496 .eh_host_reset_handler = fdomain_host_reset,
497 .bios_param = fdomain_biosparam,
501 .dma_boundary = PAGE_SIZE - 1,
504 struct Scsi_Host *fdomain_create(int base, int irq, int this_id,
507 struct Scsi_Host *sh;
510 static const char * const chip_names[] = {
511 "Unknown", "TMC-1800", "TMC-18C50", "TMC-18C30"
513 unsigned long irq_flags = 0;
515 chip = fdomain_identify(base);
521 if (fdomain_test_loopback(base))
525 dev_err(dev, "card has no IRQ assigned");
529 sh = scsi_host_alloc(&fdomain_template, sizeof(struct fdomain));
534 sh->this_id = this_id & 0x07;
538 sh->n_io_port = FDOMAIN_REGION_SIZE;
543 INIT_WORK(&fd->work, fdomain_work);
545 if (dev_is_pci(dev) || !strcmp(dev->bus->name, "pcmcia"))
546 irq_flags = IRQF_SHARED;
548 if (request_irq(irq, fdomain_irq, irq_flags, "fdomain", fd))
551 shost_printk(KERN_INFO, sh, "%s chip at 0x%x irq %d SCSI ID %d\n",
552 dev_is_pci(dev) ? "TMC-36C70 (PCI bus)" : chip_names[chip],
553 base, irq, sh->this_id);
555 if (scsi_add_host(sh, dev))
568 EXPORT_SYMBOL_GPL(fdomain_create);
570 int fdomain_destroy(struct Scsi_Host *sh)
572 struct fdomain *fd = shost_priv(sh);
574 cancel_work_sync(&fd->work);
575 scsi_remove_host(sh);
577 free_irq(sh->irq, fd);
581 EXPORT_SYMBOL_GPL(fdomain_destroy);
583 #ifdef CONFIG_PM_SLEEP
584 static int fdomain_resume(struct device *dev)
586 struct fdomain *fd = shost_priv(dev_get_drvdata(dev));
588 fdomain_reset(fd->base);
592 static SIMPLE_DEV_PM_OPS(fdomain_pm_ops, NULL, fdomain_resume);
593 #endif /* CONFIG_PM_SLEEP */
595 MODULE_AUTHOR("Ondrej Zary, Rickard E. Faith");
596 MODULE_DESCRIPTION("Future Domain TMC-16x0/TMC-3260 SCSI driver");
597 MODULE_LICENSE("GPL");