drivers/tty/serial/clps711x.c

   1 // SPDX-License-Identifier: GPL-2.0+
   2 /*
   3  *  Driver for CLPS711x serial ports
   4  *
   5  *  Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
   6  *
   7  *  Copyright 1999 ARM Limited
   8  *  Copyright (C) 2000 Deep Blue Solutions Ltd.
   9  */
  10
  11 #include <linux/module.h>
  12 #include <linux/device.h>
  13 #include <linux/console.h>
  14 #include <linux/serial_core.h>
  15 #include <linux/serial.h>
  16 #include <linux/clk.h>
  17 #include <linux/io.h>
  18 #include <linux/tty.h>
  19 #include <linux/tty_flip.h>
  20 #include <linux/ioport.h>
  21 #include <linux/of.h>
  22 #include <linux/platform_device.h>
  23 #include <linux/regmap.h>
  24
  25 #include <linux/mfd/syscon.h>
  26 #include <linux/mfd/syscon/clps711x.h>
  27
  28 #include "serial_mctrl_gpio.h"
  29
  30 #define UART_CLPS711X_DEVNAME   "ttyCL"
  31 #define UART_CLPS711X_NR        2
  32 #define UART_CLPS711X_MAJOR     204
  33 #define UART_CLPS711X_MINOR     40
  34
  35 #define UARTDR_OFFSET           (0x00)
  36 #define UBRLCR_OFFSET           (0x40)
  37
  38 #define UARTDR_FRMERR           (1 << 8)
  39 #define UARTDR_PARERR           (1 << 9)
  40 #define UARTDR_OVERR            (1 << 10)
  41
  42 #define UBRLCR_BAUD_MASK        ((1 << 12) - 1)
  43 #define UBRLCR_BREAK            (1 << 12)
  44 #define UBRLCR_PRTEN            (1 << 13)
  45 #define UBRLCR_EVENPRT          (1 << 14)
  46 #define UBRLCR_XSTOP            (1 << 15)
  47 #define UBRLCR_FIFOEN           (1 << 16)
  48 #define UBRLCR_WRDLEN5          (0 << 17)
  49 #define UBRLCR_WRDLEN6          (1 << 17)
  50 #define UBRLCR_WRDLEN7          (2 << 17)
  51 #define UBRLCR_WRDLEN8          (3 << 17)
  52 #define UBRLCR_WRDLEN_MASK      (3 << 17)
  53
  54 struct clps711x_port {
  55         struct uart_port        port;
  56         unsigned int            tx_enabled;
  57         int                     rx_irq;
  58         struct regmap           *syscon;
  59         struct mctrl_gpios      *gpios;
  60 };
  61
  62 static struct uart_driver clps711x_uart = {
  63         .owner          = THIS_MODULE,
  64         .driver_name    = UART_CLPS711X_DEVNAME,
  65         .dev_name       = UART_CLPS711X_DEVNAME,
  66         .major          = UART_CLPS711X_MAJOR,
  67         .minor          = UART_CLPS711X_MINOR,
  68         .nr             = UART_CLPS711X_NR,
  69 };
  70
  71 static void uart_clps711x_stop_tx(struct uart_port *port)
  72 {
  73         struct clps711x_port *s = dev_get_drvdata(port->dev);
  74
  75         if (s->tx_enabled) {
  76                 disable_irq(port->irq);
  77                 s->tx_enabled = 0;
  78         }
  79 }
  80
  81 static void uart_clps711x_start_tx(struct uart_port *port)
  82 {
  83         struct clps711x_port *s = dev_get_drvdata(port->dev);
  84
  85         if (!s->tx_enabled) {
  86                 s->tx_enabled = 1;
  87                 enable_irq(port->irq);
  88         }
  89 }
  90
  91 static irqreturn_t uart_clps711x_int_rx(int irq, void *dev_id)
  92 {
  93         struct uart_port *port = dev_id;
  94         struct clps711x_port *s = dev_get_drvdata(port->dev);
  95         unsigned int status, flg;
  96         u16 ch;
  97
  98         for (;;) {
  99                 u32 sysflg = 0;
 100
 101                 regmap_read(s->syscon, SYSFLG_OFFSET, &sysflg);
 102                 if (sysflg & SYSFLG_URXFE)
 103                         break;
 104
 105                 ch = readw(port->membase + UARTDR_OFFSET);
 106                 status = ch & (UARTDR_FRMERR | UARTDR_PARERR | UARTDR_OVERR);
 107                 ch &= 0xff;
 108
 109                 port->icount.rx++;
 110                 flg = TTY_NORMAL;
 111
 112                 if (unlikely(status)) {
 113                         if (status & UARTDR_PARERR)
 114                                 port->icount.parity++;
 115                         else if (status & UARTDR_FRMERR)
 116                                 port->icount.frame++;
 117                         else if (status & UARTDR_OVERR)
 118                                 port->icount.overrun++;
 119
 120                         status &= port->read_status_mask;
 121
 122                         if (status & UARTDR_PARERR)
 123                                 flg = TTY_PARITY;
 124                         else if (status & UARTDR_FRMERR)
 125                                 flg = TTY_FRAME;
 126                         else if (status & UARTDR_OVERR)
 127                                 flg = TTY_OVERRUN;
 128                 }
 129
 130                 if (uart_handle_sysrq_char(port, ch))
 131                         continue;
 132
 133                 if (status & port->ignore_status_mask)
 134                         continue;
 135
 136                 uart_insert_char(port, status, UARTDR_OVERR, ch, flg);
 137         }
 138
 139         tty_flip_buffer_push(&port->state->port);
 140
 141         return IRQ_HANDLED;
 142 }
 143
 144 static irqreturn_t uart_clps711x_int_tx(int irq, void *dev_id)
 145 {
 146         struct uart_port *port = dev_id;
 147         struct clps711x_port *s = dev_get_drvdata(port->dev);
 148         struct circ_buf *xmit = &port->state->xmit;
 149
 150         if (port->x_char) {
 151                 writew(port->x_char, port->membase + UARTDR_OFFSET);
 152                 port->icount.tx++;
 153                 port->x_char = 0;
 154                 return IRQ_HANDLED;
 155         }
 156
 157         if (uart_circ_empty(xmit) || uart_tx_stopped(port)) {
 158                 if (s->tx_enabled) {
 159                         disable_irq_nosync(port->irq);
 160                         s->tx_enabled = 0;
 161                 }
 162                 return IRQ_HANDLED;
 163         }
 164
 165         while (!uart_circ_empty(xmit)) {
 166                 u32 sysflg = 0;
 167
 168                 writew(xmit->buf[xmit->tail], port->membase + UARTDR_OFFSET);
 169                 uart_xmit_advance(port, 1);
 170
 171                 regmap_read(s->syscon, SYSFLG_OFFSET, &sysflg);
 172                 if (sysflg & SYSFLG_UTXFF)
 173                         break;
 174         }
 175
 176         if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
 177                 uart_write_wakeup(port);
 178
 179         return IRQ_HANDLED;
 180 }
 181
 182 static unsigned int uart_clps711x_tx_empty(struct uart_port *port)
 183 {
 184         struct clps711x_port *s = dev_get_drvdata(port->dev);
 185         u32 sysflg = 0;
 186
 187         regmap_read(s->syscon, SYSFLG_OFFSET, &sysflg);
 188
 189         return (sysflg & SYSFLG_UBUSY) ? 0 : TIOCSER_TEMT;
 190 }
 191
 192 static unsigned int uart_clps711x_get_mctrl(struct uart_port *port)
 193 {
 194         unsigned int result = TIOCM_DSR | TIOCM_CTS | TIOCM_CAR;
 195         struct clps711x_port *s = dev_get_drvdata(port->dev);
 196
 197         return mctrl_gpio_get(s->gpios, &result);
 198 }
 199
 200 static void uart_clps711x_set_mctrl(struct uart_port *port, unsigned int mctrl)
 201 {
 202         struct clps711x_port *s = dev_get_drvdata(port->dev);
 203
 204         mctrl_gpio_set(s->gpios, mctrl);
 205 }
 206
 207 static void uart_clps711x_break_ctl(struct uart_port *port, int break_state)
 208 {
 209         unsigned int ubrlcr;
 210
 211         ubrlcr = readl(port->membase + UBRLCR_OFFSET);
 212         if (break_state)
 213                 ubrlcr |= UBRLCR_BREAK;
 214         else
 215                 ubrlcr &= ~UBRLCR_BREAK;
 216         writel(ubrlcr, port->membase + UBRLCR_OFFSET);
 217 }
 218
 219 static void uart_clps711x_set_ldisc(struct uart_port *port,
 220                                     struct ktermios *termios)
 221 {
 222         if (!port->line) {
 223                 struct clps711x_port *s = dev_get_drvdata(port->dev);
 224
 225                 regmap_update_bits(s->syscon, SYSCON_OFFSET, SYSCON1_SIREN,
 226                                    (termios->c_line == N_IRDA) ? SYSCON1_SIREN : 0);
 227         }
 228 }
 229
 230 static int uart_clps711x_startup(struct uart_port *port)
 231 {
 232         struct clps711x_port *s = dev_get_drvdata(port->dev);
 233
 234         /* Disable break */
 235         writel(readl(port->membase + UBRLCR_OFFSET) & ~UBRLCR_BREAK,
 236                port->membase + UBRLCR_OFFSET);
 237
 238         /* Enable the port */
 239         return regmap_update_bits(s->syscon, SYSCON_OFFSET,
 240                                   SYSCON_UARTEN, SYSCON_UARTEN);
 241 }
 242
 243 static void uart_clps711x_shutdown(struct uart_port *port)
 244 {
 245         struct clps711x_port *s = dev_get_drvdata(port->dev);
 246
 247         /* Disable the port */
 248         regmap_update_bits(s->syscon, SYSCON_OFFSET, SYSCON_UARTEN, 0);
 249 }
 250
 251 static void uart_clps711x_set_termios(struct uart_port *port,
 252                                       struct ktermios *termios,
 253                                       const struct ktermios *old)
 254 {
 255         u32 ubrlcr;
 256         unsigned int baud, quot;
 257
 258         /* Mask termios capabilities we don't support */
 259         termios->c_cflag &= ~CMSPAR;
 260         termios->c_iflag &= ~(BRKINT | IGNBRK);
 261
 262         /* Ask the core to calculate the divisor for us */
 263         baud = uart_get_baud_rate(port, termios, old, port->uartclk / 4096,
 264                                                       port->uartclk / 16);
 265         quot = uart_get_divisor(port, baud);
 266
 267         switch (termios->c_cflag & CSIZE) {
 268         case CS5:
 269                 ubrlcr = UBRLCR_WRDLEN5;
 270                 break;
 271         case CS6:
 272                 ubrlcr = UBRLCR_WRDLEN6;
 273                 break;
 274         case CS7:
 275                 ubrlcr = UBRLCR_WRDLEN7;
 276                 break;
 277         case CS8:
 278         default:
 279                 ubrlcr = UBRLCR_WRDLEN8;
 280                 break;
 281         }
 282
 283         if (termios->c_cflag & CSTOPB)
 284                 ubrlcr |= UBRLCR_XSTOP;
 285
 286         if (termios->c_cflag & PARENB) {
 287                 ubrlcr |= UBRLCR_PRTEN;
 288                 if (!(termios->c_cflag & PARODD))
 289                         ubrlcr |= UBRLCR_EVENPRT;
 290         }
 291
 292         /* Enable FIFO */
 293         ubrlcr |= UBRLCR_FIFOEN;
 294
 295         /* Set read status mask */
 296         port->read_status_mask = UARTDR_OVERR;
 297         if (termios->c_iflag & INPCK)
 298                 port->read_status_mask |= UARTDR_PARERR | UARTDR_FRMERR;
 299
 300         /* Set status ignore mask */
 301         port->ignore_status_mask = 0;
 302         if (!(termios->c_cflag & CREAD))
 303                 port->ignore_status_mask |= UARTDR_OVERR | UARTDR_PARERR |
 304                                             UARTDR_FRMERR;
 305
 306         uart_update_timeout(port, termios->c_cflag, baud);
 307
 308         writel(ubrlcr | (quot - 1), port->membase + UBRLCR_OFFSET);
 309 }
 310
 311 static const char *uart_clps711x_type(struct uart_port *port)
 312 {
 313         return (port->type == PORT_CLPS711X) ? "CLPS711X" : NULL;
 314 }
 315
 316 static void uart_clps711x_config_port(struct uart_port *port, int flags)
 317 {
 318         if (flags & UART_CONFIG_TYPE)
 319                 port->type = PORT_CLPS711X;
 320 }
 321
 322 static void uart_clps711x_nop_void(struct uart_port *port)
 323 {
 324 }
 325
 326 static int uart_clps711x_nop_int(struct uart_port *port)
 327 {
 328         return 0;
 329 }
 330
 331 static const struct uart_ops uart_clps711x_ops = {
 332         .tx_empty       = uart_clps711x_tx_empty,
 333         .set_mctrl      = uart_clps711x_set_mctrl,
 334         .get_mctrl      = uart_clps711x_get_mctrl,
 335         .stop_tx        = uart_clps711x_stop_tx,
 336         .start_tx       = uart_clps711x_start_tx,
 337         .stop_rx        = uart_clps711x_nop_void,
 338         .break_ctl      = uart_clps711x_break_ctl,
 339         .set_ldisc      = uart_clps711x_set_ldisc,
 340         .startup        = uart_clps711x_startup,
 341         .shutdown       = uart_clps711x_shutdown,
 342         .set_termios    = uart_clps711x_set_termios,
 343         .type           = uart_clps711x_type,
 344         .config_port    = uart_clps711x_config_port,
 345         .release_port   = uart_clps711x_nop_void,
 346         .request_port   = uart_clps711x_nop_int,
 347 };
 348
 349 #ifdef CONFIG_SERIAL_CLPS711X_CONSOLE
 350 static void uart_clps711x_console_putchar(struct uart_port *port, unsigned char ch)
 351 {
 352         struct clps711x_port *s = dev_get_drvdata(port->dev);
 353         u32 sysflg = 0;
 354
 355         /* Wait for FIFO is not full */
 356         do {
 357                 regmap_read(s->syscon, SYSFLG_OFFSET, &sysflg);
 358         } while (sysflg & SYSFLG_UTXFF);
 359
 360         writew(ch, port->membase + UARTDR_OFFSET);
 361 }
 362
 363 static void uart_clps711x_console_write(struct console *co, const char *c,
 364                                         unsigned n)
 365 {
 366         struct uart_port *port = clps711x_uart.state[co->index].uart_port;
 367         struct clps711x_port *s = dev_get_drvdata(port->dev);
 368         u32 sysflg = 0;
 369
 370         uart_console_write(port, c, n, uart_clps711x_console_putchar);
 371
 372         /* Wait for transmitter to become empty */
 373         do {
 374                 regmap_read(s->syscon, SYSFLG_OFFSET, &sysflg);
 375         } while (sysflg & SYSFLG_UBUSY);
 376 }
 377
 378 static int uart_clps711x_console_setup(struct console *co, char *options)
 379 {
 380         int baud = 38400, bits = 8, parity = 'n', flow = 'n';
 381         int ret, index = co->index;
 382         struct clps711x_port *s;
 383         struct uart_port *port;
 384         unsigned int quot;
 385         u32 ubrlcr;
 386
 387         if (index < 0 || index >= UART_CLPS711X_NR)
 388                 return -EINVAL;
 389
 390         port = clps711x_uart.state[index].uart_port;
 391         if (!port)
 392                 return -ENODEV;
 393
 394         s = dev_get_drvdata(port->dev);
 395
 396         if (!options) {
 397                 u32 syscon = 0;
 398
 399                 regmap_read(s->syscon, SYSCON_OFFSET, &syscon);
 400                 if (syscon & SYSCON_UARTEN) {
 401                         ubrlcr = readl(port->membase + UBRLCR_OFFSET);
 402
 403                         if (ubrlcr & UBRLCR_PRTEN) {
 404                                 if (ubrlcr & UBRLCR_EVENPRT)
 405                                         parity = 'e';
 406                                 else
 407                                         parity = 'o';
 408                         }
 409
 410                         if ((ubrlcr & UBRLCR_WRDLEN_MASK) == UBRLCR_WRDLEN7)
 411                                 bits = 7;
 412
 413                         quot = ubrlcr & UBRLCR_BAUD_MASK;
 414                         baud = port->uartclk / (16 * (quot + 1));
 415                 }
 416         } else
 417                 uart_parse_options(options, &baud, &parity, &bits, &flow);
 418
 419         ret = uart_set_options(port, co, baud, parity, bits, flow);
 420         if (ret)
 421                 return ret;
 422
 423         return regmap_update_bits(s->syscon, SYSCON_OFFSET,
 424                                   SYSCON_UARTEN, SYSCON_UARTEN);
 425 }
 426
 427 static struct console clps711x_console = {
 428         .name   = UART_CLPS711X_DEVNAME,
 429         .device = uart_console_device,
 430         .write  = uart_clps711x_console_write,
 431         .setup  = uart_clps711x_console_setup,
 432         .flags  = CON_PRINTBUFFER,
 433         .index  = -1,
 434 };
 435 #endif
 436
 437 static int uart_clps711x_probe(struct platform_device *pdev)
 438 {
 439         struct device_node *np = pdev->dev.of_node;
 440         struct clps711x_port *s;
 441         struct resource *res;
 442         struct clk *uart_clk;
 443         int irq, ret;
 444
 445         s = devm_kzalloc(&pdev->dev, sizeof(*s), GFP_KERNEL);
 446         if (!s)
 447                 return -ENOMEM;
 448
 449         uart_clk = devm_clk_get(&pdev->dev, NULL);
 450         if (IS_ERR(uart_clk))
 451                 return PTR_ERR(uart_clk);
 452
 453         res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 454         s->port.membase = devm_ioremap_resource(&pdev->dev, res);
 455         if (IS_ERR(s->port.membase))
 456                 return PTR_ERR(s->port.membase);
 457
 458         irq = platform_get_irq(pdev, 0);
 459         if (irq < 0)
 460                 return irq;
 461         s->port.irq = irq;
 462
 463         s->rx_irq = platform_get_irq(pdev, 1);
 464         if (s->rx_irq < 0)
 465                 return s->rx_irq;
 466
 467         s->syscon = syscon_regmap_lookup_by_phandle(np, "syscon");
 468         if (IS_ERR(s->syscon))
 469                 return PTR_ERR(s->syscon);
 470
 471         s->port.line            = of_alias_get_id(np, "serial");
 472         s->port.dev             = &pdev->dev;
 473         s->port.iotype          = UPIO_MEM32;
 474         s->port.mapbase         = res->start;
 475         s->port.type            = PORT_CLPS711X;
 476         s->port.fifosize        = 16;
 477         s->port.has_sysrq       = IS_ENABLED(CONFIG_SERIAL_CLPS711X_CONSOLE);
 478         s->port.flags           = UPF_SKIP_TEST | UPF_FIXED_TYPE;
 479         s->port.uartclk         = clk_get_rate(uart_clk);
 480         s->port.ops             = &uart_clps711x_ops;
 481
 482         platform_set_drvdata(pdev, s);
 483
 484         s->gpios = mctrl_gpio_init_noauto(&pdev->dev, 0);
 485         if (IS_ERR(s->gpios))
 486             return PTR_ERR(s->gpios);
 487
 488         ret = uart_add_one_port(&clps711x_uart, &s->port);
 489         if (ret)
 490                 return ret;
 491
 492         /* Disable port */
 493         if (!uart_console(&s->port))
 494                 regmap_update_bits(s->syscon, SYSCON_OFFSET, SYSCON_UARTEN, 0);
 495
 496         s->tx_enabled = 1;
 497
 498         ret = devm_request_irq(&pdev->dev, s->port.irq, uart_clps711x_int_tx, 0,
 499                                dev_name(&pdev->dev), &s->port);
 500         if (ret) {
 501                 uart_remove_one_port(&clps711x_uart, &s->port);
 502                 return ret;
 503         }
 504
 505         ret = devm_request_irq(&pdev->dev, s->rx_irq, uart_clps711x_int_rx, 0,
 506                                dev_name(&pdev->dev), &s->port);
 507         if (ret)
 508                 uart_remove_one_port(&clps711x_uart, &s->port);
 509
 510         return ret;
 511 }
 512
 513 static int uart_clps711x_remove(struct platform_device *pdev)
 514 {
 515         struct clps711x_port *s = platform_get_drvdata(pdev);
 516
 517         uart_remove_one_port(&clps711x_uart, &s->port);
 518
 519         return 0;
 520 }
 521
 522 static const struct of_device_id __maybe_unused clps711x_uart_dt_ids[] = {
 523         { .compatible = "cirrus,ep7209-uart", },
 524         { }
 525 };
 526 MODULE_DEVICE_TABLE(of, clps711x_uart_dt_ids);
 527
 528 static struct platform_driver clps711x_uart_platform = {
 529         .driver = {
 530                 .name           = "clps711x-uart",
 531                 .of_match_table = of_match_ptr(clps711x_uart_dt_ids),
 532         },
 533         .probe  = uart_clps711x_probe,
 534         .remove = uart_clps711x_remove,
 535 };
 536
 537 static int __init uart_clps711x_init(void)
 538 {
 539         int ret;
 540
 541 #ifdef CONFIG_SERIAL_CLPS711X_CONSOLE
 542         clps711x_uart.cons = &clps711x_console;
 543         clps711x_console.data = &clps711x_uart;
 544 #endif
 545
 546         ret = uart_register_driver(&clps711x_uart);
 547         if (ret)
 548                 return ret;
 549
 550         return platform_driver_register(&clps711x_uart_platform);
 551 }
 552 module_init(uart_clps711x_init);
 553
 554 static void __exit uart_clps711x_exit(void)
 555 {
 556         platform_driver_unregister(&clps711x_uart_platform);
 557         uart_unregister_driver(&clps711x_uart);
 558 }
 559 module_exit(uart_clps711x_exit);
 560
 561 MODULE_AUTHOR("Deep Blue Solutions Ltd");
 562 MODULE_DESCRIPTION("CLPS711X serial driver");
 563 MODULE_LICENSE("GPL");