[linux.git] / drivers / pcmcia / ricoh.h

/*
 * ricoh.h 1.9 1999/10/25 20:03:34
 *
 * The contents of this file are subject to the Mozilla Public License
 * Version 1.1 (the "License"); you may not use this file except in
 * compliance with the License. You may obtain a copy of the License
 * at http://www.mozilla.org/MPL/
 *
 * Software distributed under the License is distributed on an "AS IS"
 * basis, WITHOUT WARRANTY OF ANY KIND, either express or implied. See
 * the License for the specific language governing rights and
 * limitations under the License. 
 *
 * The initial developer of the original code is David A. Hinds
 * <[email protected]>.  Portions created by David A. Hinds
 * are Copyright (C) 1999 David A. Hinds.  All Rights Reserved.
 *
 * Alternatively, the contents of this file may be used under the
 * terms of the GNU General Public License version 2 (the "GPL"), in which
 * case the provisions of the GPL are applicable instead of the
 * above.  If you wish to allow the use of your version of this file
 * only under the terms of the GPL and not to allow others to use
 * your version of this file under the MPL, indicate your decision by
 * deleting the provisions above and replace them with the notice and
 * other provisions required by the GPL.  If you do not delete the
 * provisions above, a recipient may use your version of this file
 * under either the MPL or the GPL.
 */

#ifndef _LINUX_RICOH_H
#define _LINUX_RICOH_H


#define RF5C_MODE_CTL		0x1f	/* Mode control */
#define RF5C_PWR_CTL		0x2f	/* Mixed voltage control */
#define RF5C_CHIP_ID		0x3a	/* Chip identification */
#define RF5C_MODE_CTL_3		0x3b	/* Mode control 3 */

/* I/O window address offset */
#define RF5C_IO_OFF(w)		(0x36+((w)<<1))

/* Flags for RF5C_MODE_CTL */
#define RF5C_MODE_ATA		0x01	/* ATA mode */
#define RF5C_MODE_LED_ENA	0x02	/* IRQ 12 is LED */
#define RF5C_MODE_CA21		0x04
#define RF5C_MODE_CA22		0x08
#define RF5C_MODE_CA23		0x10
#define RF5C_MODE_CA24		0x20
#define RF5C_MODE_CA25		0x40
#define RF5C_MODE_3STATE_BIT7	0x80

/* Flags for RF5C_PWR_CTL */
#define RF5C_PWR_VCC_3V		0x01
#define RF5C_PWR_IREQ_HIGH	0x02
#define RF5C_PWR_INPACK_ENA	0x04
#define RF5C_PWR_5V_DET		0x08
#define RF5C_PWR_TC_SEL		0x10	/* Terminal Count: irq 11 or 15 */
#define RF5C_PWR_DREQ_LOW	0x20
#define RF5C_PWR_DREQ_OFF	0x00	/* DREQ steering control */
#define RF5C_PWR_DREQ_INPACK	0x40
#define RF5C_PWR_DREQ_SPKR	0x80
#define RF5C_PWR_DREQ_IOIS16	0xc0

/* Values for RF5C_CHIP_ID */
#define RF5C_CHIP_RF5C296	0x32
#define RF5C_CHIP_RF5C396	0xb2

/* Flags for RF5C_MODE_CTL_3 */
#define RF5C_MCTL3_DISABLE	0x01	/* Disable PCMCIA interface */
#define RF5C_MCTL3_DMA_ENA	0x02

/* Register definitions for Ricoh PCI-to-CardBus bridges */

/* Extra bits in CB_BRIDGE_CONTROL */
#define RL5C46X_BCR_3E0_ENA		0x0800
#define RL5C46X_BCR_3E2_ENA		0x1000

/* Bridge Configuration Register */
#define RL5C4XX_CONFIG			0x80	/* 16 bit */
#define  RL5C4XX_CONFIG_IO_1_MODE	0x0200
#define  RL5C4XX_CONFIG_IO_0_MODE	0x0100
#define  RL5C4XX_CONFIG_PREFETCH	0x0001

/* Misc Control Register */
#define RL5C4XX_MISC			0x0082	/* 16 bit */
#define  RL5C4XX_MISC_HW_SUSPEND_ENA	0x0002
#define  RL5C4XX_MISC_VCCEN_POL		0x0100
#define  RL5C4XX_MISC_VPPEN_POL		0x0200
#define  RL5C46X_MISC_SUSPEND		0x0001
#define  RL5C46X_MISC_PWR_SAVE_2	0x0004
#define  RL5C46X_MISC_IFACE_BUSY	0x0008
#define  RL5C46X_MISC_B_LOCK		0x0010
#define  RL5C46X_MISC_A_LOCK		0x0020
#define  RL5C46X_MISC_PCI_LOCK		0x0040
#define  RL5C47X_MISC_IFACE_BUSY	0x0004
#define  RL5C47X_MISC_PCI_INT_MASK	0x0018
#define  RL5C47X_MISC_PCI_INT_DIS	0x0020
#define  RL5C47X_MISC_SUBSYS_WR		0x0040
#define  RL5C47X_MISC_SRIRQ_ENA		0x0080
#define  RL5C47X_MISC_5V_DISABLE	0x0400
#define  RL5C47X_MISC_LED_POL		0x0800

/* 16-bit Interface Control Register */
#define RL5C4XX_16BIT_CTL		0x0084	/* 16 bit */
#define  RL5C4XX_16CTL_IO_TIMING	0x0100
#define  RL5C4XX_16CTL_MEM_TIMING	0x0200
#define  RL5C46X_16CTL_LEVEL_1		0x0010
#define  RL5C46X_16CTL_LEVEL_2		0x0020

/* 16-bit IO and memory timing registers */
#define RL5C4XX_16BIT_IO_0		0x0088	/* 16 bit */
#define RL5C4XX_16BIT_MEM_0		0x008a	/* 16 bit */
#define  RL5C4XX_SETUP_MASK		0x0007
#define  RL5C4XX_SETUP_SHIFT		0
#define  RL5C4XX_CMD_MASK		0x01f0
#define  RL5C4XX_CMD_SHIFT		4
#define  RL5C4XX_HOLD_MASK		0x1c00
#define  RL5C4XX_HOLD_SHIFT		10
#define  RL5C4XX_MISC_CONTROL           0x2F /* 8 bit */
#define  RL5C4XX_ZV_ENABLE              0x08

#ifdef __YENTA_H

#define rl_misc(socket)		((socket)->private[0])
#define rl_ctl(socket)		((socket)->private[1])
#define rl_io(socket)		((socket)->private[2])
#define rl_mem(socket)		((socket)->private[3])
#define rl_config(socket)	((socket)->private[4])

static void ricoh_zoom_video(struct pcmcia_socket *sock, int onoff)
{
        u8 reg;
	struct yenta_socket *socket = container_of(sock, struct yenta_socket, socket);

        reg = config_readb(socket, RL5C4XX_MISC_CONTROL);
        if (onoff)
                /* Zoom zoom, we will all go together, zoom zoom, zoom zoom */
                reg |=  RL5C4XX_ZV_ENABLE;
        else
                reg &= ~RL5C4XX_ZV_ENABLE;
	
        config_writeb(socket, RL5C4XX_MISC_CONTROL, reg);
}

static void ricoh_set_zv(struct yenta_socket *socket)
{
        if(socket->dev->vendor == PCI_VENDOR_ID_RICOH)
        {
                switch(socket->dev->device)
                {
                        /* There may be more .. */
		case  PCI_DEVICE_ID_RICOH_RL5C478:
			socket->socket.zoom_video = ricoh_zoom_video;
			break;  
                }
        }
}

static void ricoh_save_state(struct yenta_socket *socket)
{
	rl_misc(socket) = config_readw(socket, RL5C4XX_MISC);
	rl_ctl(socket) = config_readw(socket, RL5C4XX_16BIT_CTL);
	rl_io(socket) = config_readw(socket, RL5C4XX_16BIT_IO_0);
	rl_mem(socket) = config_readw(socket, RL5C4XX_16BIT_MEM_0);
	rl_config(socket) = config_readw(socket, RL5C4XX_CONFIG);
}

static void ricoh_restore_state(struct yenta_socket *socket)
{
	config_writew(socket, RL5C4XX_MISC, rl_misc(socket));
	config_writew(socket, RL5C4XX_16BIT_CTL, rl_ctl(socket));
	config_writew(socket, RL5C4XX_16BIT_IO_0, rl_io(socket));
	config_writew(socket, RL5C4XX_16BIT_MEM_0, rl_mem(socket));
	config_writew(socket, RL5C4XX_CONFIG, rl_config(socket));
}


/*
 * Magic Ricoh initialization code..
 */
static int ricoh_override(struct yenta_socket *socket)
{
	u16 config, ctl;

	config = config_readw(socket, RL5C4XX_CONFIG);

	/* Set the default timings, don't trust the original values */
	ctl = RL5C4XX_16CTL_IO_TIMING | RL5C4XX_16CTL_MEM_TIMING;

	if(socket->dev->device < PCI_DEVICE_ID_RICOH_RL5C475) {
		ctl |= RL5C46X_16CTL_LEVEL_1 | RL5C46X_16CTL_LEVEL_2;
	} else {
		config |= RL5C4XX_CONFIG_PREFETCH;
	}

	config_writew(socket, RL5C4XX_16BIT_CTL, ctl);
	config_writew(socket, RL5C4XX_CONFIG, config);

	ricoh_set_zv(socket);

	return 0;
}

#endif /* CONFIG_CARDBUS */

#endif /* _LINUX_RICOH_H */
Commit	Line	Data
1da177e4 LT	1	/*
	2	* ricoh.h 1.9 1999/10/25 20:03:34
	3	*
	4	* The contents of this file are subject to the Mozilla Public License
	5	* Version 1.1 (the "License"); you may not use this file except in
	6	* compliance with the License. You may obtain a copy of the License
	7	* at http://www.mozilla.org/MPL/
	8	*
	9	* Software distributed under the License is distributed on an "AS IS"
	10	* basis, WITHOUT WARRANTY OF ANY KIND, either express or implied. See
	11	* the License for the specific language governing rights and
	12	* limitations under the License.
	13	*
	14	* The initial developer of the original code is David A. Hinds
	15	* <[email protected]>. Portions created by David A. Hinds
	16	* are Copyright (C) 1999 David A. Hinds. All Rights Reserved.
	17	*
	18	* Alternatively, the contents of this file may be used under the
	19	* terms of the GNU General Public License version 2 (the "GPL"), in which
	20	* case the provisions of the GPL are applicable instead of the
	21	* above. If you wish to allow the use of your version of this file
	22	* only under the terms of the GPL and not to allow others to use
	23	* your version of this file under the MPL, indicate your decision by
	24	* deleting the provisions above and replace them with the notice and
	25	* other provisions required by the GPL. If you do not delete the
	26	* provisions above, a recipient may use your version of this file
	27	* under either the MPL or the GPL.
	28	*/
	29
	30	#ifndef _LINUX_RICOH_H
	31	#define _LINUX_RICOH_H
	32
	33
	34	#define RF5C_MODE_CTL 0x1f /* Mode control */
	35	#define RF5C_PWR_CTL 0x2f /* Mixed voltage control */
	36	#define RF5C_CHIP_ID 0x3a /* Chip identification */
	37	#define RF5C_MODE_CTL_3 0x3b /* Mode control 3 */
	38
	39	/* I/O window address offset */
	40	#define RF5C_IO_OFF(w) (0x36+((w)<<1))
	41
	42	/* Flags for RF5C_MODE_CTL */
	43	#define RF5C_MODE_ATA 0x01 /* ATA mode */
	44	#define RF5C_MODE_LED_ENA 0x02 /* IRQ 12 is LED */
	45	#define RF5C_MODE_CA21 0x04
	46	#define RF5C_MODE_CA22 0x08
	47	#define RF5C_MODE_CA23 0x10
	48	#define RF5C_MODE_CA24 0x20
	49	#define RF5C_MODE_CA25 0x40
	50	#define RF5C_MODE_3STATE_BIT7 0x80
	51
	52	/* Flags for RF5C_PWR_CTL */
	53	#define RF5C_PWR_VCC_3V 0x01
	54	#define RF5C_PWR_IREQ_HIGH 0x02
	55	#define RF5C_PWR_INPACK_ENA 0x04
	56	#define RF5C_PWR_5V_DET 0x08
	57	#define RF5C_PWR_TC_SEL 0x10 /* Terminal Count: irq 11 or 15 */
	58	#define RF5C_PWR_DREQ_LOW 0x20
	59	#define RF5C_PWR_DREQ_OFF 0x00 /* DREQ steering control */
	60	#define RF5C_PWR_DREQ_INPACK 0x40
	61	#define RF5C_PWR_DREQ_SPKR 0x80
	62	#define RF5C_PWR_DREQ_IOIS16 0xc0
	63
	64	/* Values for RF5C_CHIP_ID */
65	#define RF5C_CHIP_RF5C296 0x32
66	#define RF5C_CHIP_RF5C396 0xb2
67
68	/* Flags for RF5C_MODE_CTL_3 */
69	#define RF5C_MCTL3_DISABLE 0x01 /* Disable PCMCIA interface */
70	#define RF5C_MCTL3_DMA_ENA 0x02
71
72	/* Register definitions for Ricoh PCI-to-CardBus bridges */
73
74	/* Extra bits in CB_BRIDGE_CONTROL */
75	#define RL5C46X_BCR_3E0_ENA 0x0800
76	#define RL5C46X_BCR_3E2_ENA 0x1000
77
78	/* Bridge Configuration Register */
79	#define RL5C4XX_CONFIG 0x80 /* 16 bit */
80	#define RL5C4XX_CONFIG_IO_1_MODE 0x0200
81	#define RL5C4XX_CONFIG_IO_0_MODE 0x0100
82	#define RL5C4XX_CONFIG_PREFETCH 0x0001
83
84	/* Misc Control Register */
85	#define RL5C4XX_MISC 0x0082 /* 16 bit */
86	#define RL5C4XX_MISC_HW_SUSPEND_ENA 0x0002
87	#define RL5C4XX_MISC_VCCEN_POL 0x0100
88	#define RL5C4XX_MISC_VPPEN_POL 0x0200
89	#define RL5C46X_MISC_SUSPEND 0x0001
90	#define RL5C46X_MISC_PWR_SAVE_2 0x0004
91	#define RL5C46X_MISC_IFACE_BUSY 0x0008
92	#define RL5C46X_MISC_B_LOCK 0x0010
93	#define RL5C46X_MISC_A_LOCK 0x0020
94	#define RL5C46X_MISC_PCI_LOCK 0x0040
95	#define RL5C47X_MISC_IFACE_BUSY 0x0004
96	#define RL5C47X_MISC_PCI_INT_MASK 0x0018
97	#define RL5C47X_MISC_PCI_INT_DIS 0x0020
98	#define RL5C47X_MISC_SUBSYS_WR 0x0040
99	#define RL5C47X_MISC_SRIRQ_ENA 0x0080
100	#define RL5C47X_MISC_5V_DISABLE 0x0400
101	#define RL5C47X_MISC_LED_POL 0x0800
102
103	/* 16-bit Interface Control Register */
104	#define RL5C4XX_16BIT_CTL 0x0084 /* 16 bit */
105	#define RL5C4XX_16CTL_IO_TIMING 0x0100
106	#define RL5C4XX_16CTL_MEM_TIMING 0x0200
107	#define RL5C46X_16CTL_LEVEL_1 0x0010
108	#define RL5C46X_16CTL_LEVEL_2 0x0020
109
110	/* 16-bit IO and memory timing registers */
111	#define RL5C4XX_16BIT_IO_0 0x0088 /* 16 bit */
112	#define RL5C4XX_16BIT_MEM_0 0x008a /* 16 bit */
113	#define RL5C4XX_SETUP_MASK 0x0007
114	#define RL5C4XX_SETUP_SHIFT 0
115	#define RL5C4XX_CMD_MASK 0x01f0
116	#define RL5C4XX_CMD_SHIFT 4
117	#define RL5C4XX_HOLD_MASK 0x1c00
118	#define RL5C4XX_HOLD_SHIFT 10
119	#define RL5C4XX_MISC_CONTROL 0x2F /* 8 bit */
120	#define RL5C4XX_ZV_ENABLE 0x08
121
122	#ifdef __YENTA_H
123
124	#define rl_misc(socket) ((socket)->private[0])
125	#define rl_ctl(socket) ((socket)->private[1])
126	#define rl_io(socket) ((socket)->private[2])
127	#define rl_mem(socket) ((socket)->private[3])
128	#define rl_config(socket) ((socket)->private[4])
129
130	static void ricoh_zoom_video(struct pcmcia_socket *sock, int onoff)
131	{
132	u8 reg;
133	struct yenta_socket *socket = container_of(sock, struct yenta_socket, socket);
134
135	reg = config_readb(socket, RL5C4XX_MISC_CONTROL);
136	if (onoff)
137	/* Zoom zoom, we will all go together, zoom zoom, zoom zoom */
138	reg \|= RL5C4XX_ZV_ENABLE;
139	else
140	reg &= ~RL5C4XX_ZV_ENABLE;
141
142	config_writeb(socket, RL5C4XX_MISC_CONTROL, reg);
143	}
144
145	static void ricoh_set_zv(struct yenta_socket *socket)
146	{
147	if(socket->dev->vendor == PCI_VENDOR_ID_RICOH)
148	{
149	switch(socket->dev->device)
150	{
151	/* There may be more .. */
152	case PCI_DEVICE_ID_RICOH_RL5C478:
153	socket->socket.zoom_video = ricoh_zoom_video;
154	break;
155	}
156	}
157	}
158
159	static void ricoh_save_state(struct yenta_socket *socket)
160	{
161	rl_misc(socket) = config_readw(socket, RL5C4XX_MISC);
162	rl_ctl(socket) = config_readw(socket, RL5C4XX_16BIT_CTL);
163	rl_io(socket) = config_readw(socket, RL5C4XX_16BIT_IO_0);
164	rl_mem(socket) = config_readw(socket, RL5C4XX_16BIT_MEM_0);
165	rl_config(socket) = config_readw(socket, RL5C4XX_CONFIG);
166	}
167
168	static void ricoh_restore_state(struct yenta_socket *socket)
169	{
170	config_writew(socket, RL5C4XX_MISC, rl_misc(socket));
171	config_writew(socket, RL5C4XX_16BIT_CTL, rl_ctl(socket));
172	config_writew(socket, RL5C4XX_16BIT_IO_0, rl_io(socket));
173	config_writew(socket, RL5C4XX_16BIT_MEM_0, rl_mem(socket));
174	config_writew(socket, RL5C4XX_CONFIG, rl_config(socket));
175	}
176
177
178	/*
179	* Magic Ricoh initialization code..
180	*/
181	static int ricoh_override(struct yenta_socket *socket)
182	{
183	u16 config, ctl;
184
185	config = config_readw(socket, RL5C4XX_CONFIG);
186
187	/* Set the default timings, don't trust the original values */
188	ctl = RL5C4XX_16CTL_IO_TIMING \| RL5C4XX_16CTL_MEM_TIMING;
189
190	if(socket->dev->device < PCI_DEVICE_ID_RICOH_RL5C475) {
191	ctl \|= RL5C46X_16CTL_LEVEL_1 \| RL5C46X_16CTL_LEVEL_2;
192	} else {
193	config \|= RL5C4XX_CONFIG_PREFETCH;
194	}
195
196	config_writew(socket, RL5C4XX_16BIT_CTL, ctl);
197	config_writew(socket, RL5C4XX_CONFIG, config);
198
199	ricoh_set_zv(socket);
200
201	return 0;
202	}
203
204	#endif /* CONFIG_CARDBUS */
205
206	#endif /* _LINUX_RICOH_H */