armada-3720-db.dtb \
armada-3720-espressobin.dtb \
armada-3720-turris-mox.dtb \
+ armada-3720-eDPU.dtb \
armada-3720-uDPU.dtb \
armada-375-db.dtb \
armada-385-atl-x530.dtb \
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+
+/ {
+ smbios {
+ compatible = "u-boot,sysinfo-smbios";
+
+ smbios {
+ system {
+ product = "eDPU";
+ };
+
+ baseboard {
+ product = "eDPU";
+ };
+
+ chassis {
+ product = "eDPU";
+ };
+ };
+ };
+};
+
+&spi0 {
+ u-boot,dm-pre-reloc;
+
+ spi-flash@0 {
+ u-boot,dm-pre-reloc;
+ };
+};
+
+&sdhci0 {
+ u-boot,dm-pre-reloc;
+};
+
+ð0 {
+ /* G.hn does not work without additional configuration */
+ status = "disabled";
+};
+
+ð1 {
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include "armada-3720-uDPU.dtsi"
+
+/ {
+ model = "Methode eDPU Board";
+ compatible = "methode,edpu", "marvell,armada3720", "marvell,armada3710";
+};
+
+ð0 {
+ phy-mode = "2500base-x";
+};
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
-/*
- * Device tree for the uDPU board.
- * Based on Marvell Armada 3720 development board (DB-88F3720-DDR3)
- * Copyright (C) 2016 Marvell
- * Copyright (C) 2019 Methode Electronics
- * Copyright (C) 2019 Telus
- *
- */
/dts-v1/;
-#include <dt-bindings/gpio/gpio.h>
-#include "armada-372x.dtsi"
+#include "armada-3720-uDPU.dtsi"
/ {
model = "Methode uDPU Board";
compatible = "methode,udpu", "marvell,armada3720", "marvell,armada3710";
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
- memory@0 {
- device_type = "memory";
- reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
- };
-
- leds {
- compatible = "gpio-leds";
-
- led-power1 {
- label = "udpu:green:power";
- gpios = <&gpionb 11 GPIO_ACTIVE_LOW>;
- };
-
- led-power2 {
- label = "udpu:red:power";
- gpios = <&gpionb 12 GPIO_ACTIVE_LOW>;
- };
-
- led-network1 {
- label = "udpu:green:network";
- gpios = <&gpionb 13 GPIO_ACTIVE_LOW>;
- };
-
- led-network2 {
- label = "udpu:red:network";
- gpios = <&gpionb 14 GPIO_ACTIVE_LOW>;
- };
-
- led-alarm1 {
- label = "udpu:green:alarm";
- gpios = <&gpionb 15 GPIO_ACTIVE_LOW>;
- };
-
- led-alarm2 {
- label = "udpu:red:alarm";
- gpios = <&gpionb 16 GPIO_ACTIVE_LOW>;
- };
- };
-
sfp_eth0: sfp-eth0 {
compatible = "sff,sfp";
i2c-bus = <&i2c0>;
tx-fault-gpio = <&gpiosb 5 GPIO_ACTIVE_HIGH>;
maximum-power-milliwatt = <3000>;
};
-
- sfp_eth1: sfp-eth1 {
- compatible = "sff,sfp";
- i2c-bus = <&i2c1>;
- los-gpio = <&gpiosb 7 GPIO_ACTIVE_HIGH>;
- mod-def0-gpio = <&gpiosb 8 GPIO_ACTIVE_LOW>;
- tx-disable-gpio = <&gpiosb 9 GPIO_ACTIVE_HIGH>;
- tx-fault-gpio = <&gpiosb 10 GPIO_ACTIVE_HIGH>;
- maximum-power-milliwatt = <3000>;
- };
-};
-
-&sdhci0 {
- status = "okay";
- bus-width = <8>;
- mmc-ddr-1_8v;
- mmc-hs400-1_8v;
- marvell,pad-type = "fixed-1-8v";
- non-removable;
- no-sd;
- no-sdio;
-};
-
-&spi0 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&spi_quad_pins>;
-
- flash@0 {
- compatible = "jedec,spi-nor";
- reg = <0>;
- spi-max-frequency = <54000000>;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- partition@0 {
- label = "firmware";
- reg = <0x0 0x180000>;
- };
-
- partition@180000 {
- label = "u-boot-env";
- reg = <0x180000 0x10000>;
- };
- };
- };
};
&pinctrl_nb {
groups = "i2c1";
function = "gpio";
};
-
- i2c2_recovery_pins: i2c2-recovery-pins {
- groups = "i2c2";
- function = "gpio";
- };
};
&i2c0 {
sda-gpios = <&gpionb 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
};
-&i2c1 {
- status = "okay";
- pinctrl-names = "default", "recovery";
- pinctrl-0 = <&i2c2_pins>;
- pinctrl-1 = <&i2c2_recovery_pins>;
- /delete-property/mrvl,i2c-fast-mode;
- scl-gpios = <&gpionb 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
- sda-gpios = <&gpionb 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-
- temp-sensor@48 {
- compatible = "ti,tmp75c";
- reg = <0x48>;
- };
-
- temp-sensor@49 {
- compatible = "ti,tmp75c";
- reg = <0x49>;
- };
-};
-
ð0 {
phy-mode = "sgmii";
- status = "okay";
- managed = "in-band-status";
- phys = <&comphy1 0>;
sfp = <&sfp_eth0>;
};
-
-ð1 {
- phy-mode = "sgmii";
- status = "okay";
- managed = "in-band-status";
- phys = <&comphy0 1>;
- sfp = <&sfp_eth1>;
-};
-
-&usb3 {
- status = "okay";
- phys = <&usb2_utmi_otg_phy>;
- phy-names = "usb2-utmi-otg-phy";
-};
-
-&uart0 {
- status = "okay";
-};
--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device tree for the uDPU board.
+ * Based on Marvell Armada 3720 development board (DB-88F3720-DDR3)
+ * Copyright (C) 2016 Marvell
+ * Copyright (C) 2019 Methode Electronics
+ * Copyright (C) 2019 Telus
+ *
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include "armada-372x.dtsi"
+
+/ {
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-power1 {
+ label = "udpu:green:power";
+ gpios = <&gpionb 11 GPIO_ACTIVE_LOW>;
+ };
+
+ led-power2 {
+ label = "udpu:red:power";
+ gpios = <&gpionb 12 GPIO_ACTIVE_LOW>;
+ };
+
+ led-network1 {
+ label = "udpu:green:network";
+ gpios = <&gpionb 13 GPIO_ACTIVE_LOW>;
+ };
+
+ led-network2 {
+ label = "udpu:red:network";
+ gpios = <&gpionb 14 GPIO_ACTIVE_LOW>;
+ };
+
+ led-alarm1 {
+ label = "udpu:green:alarm";
+ gpios = <&gpionb 15 GPIO_ACTIVE_LOW>;
+ };
+
+ led-alarm2 {
+ label = "udpu:red:alarm";
+ gpios = <&gpionb 16 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ sfp_eth1: sfp-eth1 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c1>;
+ los-gpio = <&gpiosb 7 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpio = <&gpiosb 8 GPIO_ACTIVE_LOW>;
+ tx-disable-gpio = <&gpiosb 9 GPIO_ACTIVE_HIGH>;
+ tx-fault-gpio = <&gpiosb 10 GPIO_ACTIVE_HIGH>;
+ maximum-power-milliwatt = <3000>;
+ };
+};
+
+&sdhci0 {
+ status = "okay";
+ bus-width = <8>;
+ mmc-ddr-1_8v;
+ mmc-hs400-1_8v;
+ marvell,pad-type = "fixed-1-8v";
+ non-removable;
+ no-sd;
+ no-sdio;
+};
+
+&spi0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi_quad_pins>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <54000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "firmware";
+ reg = <0x0 0x180000>;
+ };
+
+ partition@180000 {
+ label = "u-boot-env";
+ reg = <0x180000 0x10000>;
+ };
+ };
+ };
+};
+
+&pinctrl_nb {
+ i2c2_recovery_pins: i2c2-recovery-pins {
+ groups = "i2c2";
+ function = "gpio";
+ };
+};
+
+&i2c1 {
+ status = "okay";
+ pinctrl-names = "default", "recovery";
+ pinctrl-0 = <&i2c2_pins>;
+ pinctrl-1 = <&i2c2_recovery_pins>;
+ /delete-property/mrvl,i2c-fast-mode;
+ scl-gpios = <&gpionb 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&gpionb 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+
+ temp-sensor@48 {
+ compatible = "ti,tmp75c";
+ reg = <0x48>;
+ };
+
+ temp-sensor@49 {
+ compatible = "ti,tmp75c";
+ reg = <0x49>;
+ };
+};
+
+ð0 {
+ status = "okay";
+ managed = "in-band-status";
+ phys = <&comphy1 0>;
+};
+
+ð1 {
+ phy-mode = "sgmii";
+ status = "okay";
+ managed = "in-band-status";
+ phys = <&comphy0 1>;
+ sfp = <&sfp_eth1>;
+};
+
+&usb3 {
+ status = "okay";
+ phys = <&usb2_utmi_otg_phy>;
+ phy-names = "usb2-utmi-otg-phy";
+};
+
+&uart0 {
+ status = "okay";
+};
--- /dev/null
+CONFIG_ARM=y
+CONFIG_ARCH_CPU_INIT=y
+CONFIG_ARCH_MVEBU=y
+CONFIG_SYS_TEXT_BASE=0x00000000
+CONFIG_TARGET_MVEBU_ARMADA_37XX=y
+CONFIG_MVEBU_EFUSE=y
+CONFIG_ENV_SIZE=0x10000
+CONFIG_ENV_OFFSET=0x180000
+CONFIG_ENV_SECT_SIZE=0x10000
+CONFIG_DM_GPIO=y
+CONFIG_DEFAULT_DEVICE_TREE="armada-3720-eDPU"
+CONFIG_DEBUG_UART_BASE=0xd0012000
+CONFIG_SYS_LOAD_ADDR=0x6000000
+CONFIG_DEBUG_UART=y
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
+CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xff0000
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_FIT=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_USE_PREBOOT=y
+# CONFIG_DISPLAY_CPUINFO is not set
+# CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_DISPLAY_BOARDINFO_LATE=y
+CONFIG_ARCH_EARLY_INIT_R=y
+CONFIG_BOARD_EARLY_INIT_F=y
+CONFIG_SYS_PROMPT="eDPU>> "
+CONFIG_SYS_MAXARGS=32
+CONFIG_SYS_PBSIZE=1048
+# CONFIG_CMD_ELF is not set
+# CONFIG_CMD_IMI is not set
+# CONFIG_CMD_XIMG is not set
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_FUSE=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_MTD=y
+# CONFIG_CMD_SCSI is not set
+CONFIG_CMD_SPI=y
+CONFIG_CMD_USB=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_TFTPPUT=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_TIME=y
+CONFIG_CMD_MVEBU_BUBT=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_MAC_PARTITION=y
+CONFIG_ENV_OVERWRITE=y
+CONFIG_ENV_IS_IN_SPI_FLASH=y
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_ARP_TIMEOUT=200
+CONFIG_NET_RETRY_COUNT=50
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_LBA48=y
+CONFIG_SYS_64BIT_LBA=y
+CONFIG_CLK=y
+CONFIG_CLK_MVEBU=y
+CONFIG_DM_I2C=y
+CONFIG_DM_I2C_GPIO=y
+CONFIG_SYS_I2C_MV=y
+CONFIG_MISC=y
+CONFIG_MMC_HS200_SUPPORT=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_SDMA=y
+CONFIG_MMC_SDHCI_XENON=y
+CONFIG_MTD=y
+CONFIG_DM_MTD=y
+CONFIG_SPI_FLASH_SFDP_SUPPORT=y
+CONFIG_SPI_FLASH_MACRONIX=y
+CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_SPI_FLASH_STMICRO=y
+# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
+CONFIG_SPI_FLASH_MTD=y
+CONFIG_PHYLIB_10G=y
+CONFIG_PHY_MARVELL=y
+CONFIG_PHY_FIXED=y
+CONFIG_PHY_GIGE=y
+CONFIG_MVNETA=y
+CONFIG_MVMDIO=y
+CONFIG_PHY=y
+CONFIG_MVEBU_COMPHY_SUPPORT=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_ARMADA_37XX=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
+CONFIG_DM_SCSI=y
+CONFIG_MVEBU_A3700_UART=y
+CONFIG_MVEBU_A3700_SPI=y
+CONFIG_SYSINFO=y
+CONFIG_SYSINFO_SMBIOS=y
+CONFIG_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_HOST_ETHER=y
+CONFIG_USB_ETHER_ASIX=y
+CONFIG_USB_ETHER_MCS7830=y
+CONFIG_USB_ETHER_RTL8152=y
+CONFIG_USB_ETHER_SMSC95XX=y
+CONFIG_LZO=y
projects / J-u-boot.git / commitdiff