F: drivers/mmc/stm32_sdmmc2.c
F: drivers/phy/phy-stm32-usbphyc.c
F: drivers/pinctrl/pinctrl_stm32.c
+F: drivers/power/pmic/stpmic1.c
F: drivers/power/regulator/stm32-vrefbuf.c
+F: drivers/power/regulator/stpmic1.c
F: drivers/ram/stm32mp1/
F: drivers/misc/stm32_rcc.c
F: drivers/reset/stm32-reset.c
F: arch/arm/include/asm/arch-stv0991/
ARM SUNXI
- M: Jagan Teki <jagan@openedev.com>
+ M: Jagan Teki <jagan@amarulasolutions.com>
S: Maintained
T: git git://git.denx.de/u-boot-sunxi.git
F: arch/sh/
SPI
- M: Jagan Teki <jagan@openedev.com>
+ M: Jagan Teki <jagan@amarulasolutions.com>
S: Maintained
T: git git://git.denx.de/u-boot-spi.git
F: drivers/spi/
F: include/spi*
SPI-NOR
- M: Jagan Teki <jagan@openedev.com>
+ M: Jagan Teki <jagan@amarulasolutions.com>
S: Maintained
F: drivers/mtd/spi/
status = "okay";
};
- spi0: spi@10600 {
- status = "okay";
- u-boot,dm-pre-reloc;
-
- spi-flash@0 {
- u-boot,dm-pre-reloc;
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "n25q128a13", "jedec,spi-nor";
- reg = <0>; /* Chip select 0 */
- spi-max-frequency = <27777777>;
- };
-
- fpga@1 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "spi-generic-device";
- reg = <1>; /* Chip select 1 */
- spi-max-frequency = <27777777>;
- };
- };
-
- spi1: spi@10680 {
- status = "okay";
-
- fpga@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "spi-generic-device";
- reg = <0>; /* Chip select 0 */
- spi-max-frequency = <27777777>;
- };
- };
-
/* The LCD controller is only used on this board */
lcd0: lcd-controller@e0000 {
compatible = "marvell,armada-xp-lcd";
};
};
- compatible = "n25q128a13", "jedec,spi-nor", "spi-flash";
+&spi0 {
+ status = "okay";
+ u-boot,dm-pre-reloc;
+
+ spi-flash@0 {
+ u-boot,dm-pre-reloc;
+ #address-cells = <1>;
+ #size-cells = <1>;
++ compatible = "n25q128a13", "jedec,spi-nor";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <27777777>;
+ };
+
+ fpga@1 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spi-generic-device";
+ reg = <1>; /* Chip select 1 */
+ spi-max-frequency = <27777777>;
+ };
+};
+
+&spi1 {
+ status = "okay";
+
+ fpga@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spi-generic-device";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <27777777>;
+ };
+};
+
+
&pciec {
status = "okay";
* Copyright (C) Adam Ford
*/
+/ {
+ soc@1c00000 {
+ u-boot,dm-spl;
+ };
+};
+
&flash {
- compatible = "m25p64", "spi-flash";
+ compatible = "m25p64", "jedec,spi-nor";
};
+
+&mmc0 {
+ u-boot,dm-spl;
+};
+
+&serial2 {
+ u-boot,dm-spl;
+};
+
+&spi1 {
+ u-boot,dm-spl;
+};
status = "okay";
ethphy0: ethernet-phy@0 {
reg = <0>;
- phy-mode = "rgmii-id";
};
};
spi_nor: flash@0 {
#address-cells = <1>;
#size-cells = <1>;
- compatible = "spi-flash";
+ compatible = "jedec,spi-nor";
spi-max-frequency = <50000000>;
m25p,fast-read;
reg = <0>;
status = "okay";
flash0: m25p80@0 {
- compatible = "s25fl512s","spi-flash";
+ compatible = "s25fl512s","jedec,spi-nor";
reg = <0>;
spi-tx-bus-width = <1>;
spi-rx-bus-width = <4>;
/dts-v1/;
#include "keystone-k2g.dtsi"
+#include <dt-bindings/net/ti-dp83867.h>
/ {
compatible = "ti,k2g-ice", "ti,k2g", "ti,keystone";
status = "okay";
flash0: m25p80@0 {
- compatible = "s25fl256s1", "spi-flash";
+ compatible = "s25fl256s1", "jedec,spi-nor";
reg = <0>;
spi-tx-bus-width = <1>;
spi-rx-bus-width = <4>;
};
};
};
+
+&qmss {
+ status = "okay";
+};
+
+&knav_dmas {
+ status = "okay";
+};
+
+&netcp {
+ pinctrl-names = "default";
+ //pinctrl-0 = <&emac_pins>;
+ status = "okay";
+};
+
+&mdio {
+ pinctrl-names = "default";
+ //pinctrl-0 = <&mdio_pins>;
+ status = "okay";
+ ethphy0: ethernet-phy@0 {
+ reg = <0>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
+ ti,tx-internal-delay = <DP83867_RGMIIDCTL_250_PS>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_8_B_NIB>;
+ ti,min-output-impedance;
+ ti,dp83867-rxctrl-strap-quirk;
+ };
+};
+
+&gbe0 {
+ phy-handle = <ðphy0>;
+ phy-mode = "rgmii-id";
+ status = "okay";
+};
/ {
aliases {
- spi0 = &qspi;
+ gpio26 = &stmfx_pinctrl;
i2c1 = &i2c2;
i2c4 = &i2c5;
+ pinctrl2 = &stmfx_pinctrl;
+ spi0 = &qspi;
};
};
&flash0 {
- compatible = "spi-flash";
+ compatible = "jedec,spi-nor";
+ u-boot,dm-spl;
};
&flash1 {
- compatible = "spi-flash";
+ compatible = "jedec,spi-nor";
};
-&v3v3 {
- regulator-always-on;
-};
-
-&usbotg_hs {
- g-tx-fifo-size = <576>;
-};
-
-/* SPL part **************************************/
&qspi {
u-boot,dm-spl;
};
};
};
-&flash0 {
- u-boot,dm-spl;
+&usbotg_hs {
+ g-tx-fifo-size = <576>;
};
+&v3v3 {
+ regulator-always-on;
+};
spi-flash@0 {
#address-cells = <1>;
#size-cells = <1>;
- compatible = "spi-flash";
+ compatible = "jedec,spi-nor";
memory-map = <0x9f000000 0x00800000>;
spi-max-frequency = <25000000>;
reg = <0>;
};
};
+
+&gmac1 {
+ status = "okay";
+ phy-mode = "rgmii";
+};
/ {
compatible = "gardena,smart-gateway-mt7688", "ralink,mt7628a-soc";
- model = "Gardena smart-Gateway-MT7688";
+ model = "GARDENA smart Gateway (MT7688)";
aliases {
serial0 = &uart0;
spi-flash@0 {
#address-cells = <1>;
#size-cells = <1>;
- compatible = "spi-flash", "jedec,spi-nor";
+ compatible = "jedec,spi-nor";
spi-max-frequency = <40000000>;
reg = <0>;
};
/dts-v1/;
#include "mscc,jr2.dtsi"
+#include <dt-bindings/mscc/jr2_data.h>
/ {
model = "Jaguar2 Cu8-Sfp16 PCB110 Reference Board";
&spi0 {
status = "okay";
spi-flash@0 {
- compatible = "spi-flash";
+ compatible = "jedec,spi-nor";
spi-max-frequency = <18000000>; /* input clock */
reg = <0>; /* CS0 */
};
sgpio-ports = <0x3f00ffff>;
gpio-ranges = <&sgpio2 0 0 96>;
};
+
+&mdio1 {
+ status = "okay";
+
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+ phy2: ethernet-phy@2 {
+ reg = <2>;
+ };
+ phy3: ethernet-phy@3 {
+ reg = <3>;
+ };
+ phy4: ethernet-phy@4 {
+ reg = <4>;
+ };
+ phy5: ethernet-phy@5 {
+ reg = <5>;
+ };
+ phy6: ethernet-phy@6 {
+ reg = <6>;
+ };
+ phy7: ethernet-phy@7 {
+ reg = <7>;
+ };
+};
+
+&switch {
+ ethernet-ports {
+
+ port0: port@0 {
+ reg = <0>;
+ phy-handle = <&phy0>;
+ phys = <&serdes_hsio 0 SERDES1G(1) PHY_MODE_SGMII>;
+ };
+ port1: port@1 {
+ reg = <1>;
+ phy-handle = <&phy1>;
+ phys = <&serdes_hsio 1 SERDES1G(2) PHY_MODE_SGMII>;
+ };
+ port2: port@2 {
+ reg = <2>;
+ phy-handle = <&phy2>;
+ phys = <&serdes_hsio 2 SERDES1G(3) PHY_MODE_SGMII>;
+ };
+ port3: port@3 {
+ reg = <3>;
+ phy-handle = <&phy3>;
+ phys = <&serdes_hsio 3 SERDES1G(4) PHY_MODE_SGMII>;
+ };
+ port4: port@4 {
+ reg = <4>;
+ phy-handle = <&phy4>;
+ phys = <&serdes_hsio 4 SERDES1G(5) PHY_MODE_SGMII>;
+ };
+ port5: port@5 {
+ reg = <5>;
+ phy-handle = <&phy5>;
+ phys = <&serdes_hsio 5 SERDES1G(6) PHY_MODE_SGMII>;
+ };
+ port6: port@6 {
+ reg = <6>;
+ phy-handle = <&phy6>;
+ phys = <&serdes_hsio 6 SERDES1G(7) PHY_MODE_SGMII>;
+ };
+ port7: port@7 {
+ reg = <7>;
+ phy-handle = <&phy7>;
+ phys = <&serdes_hsio 7 SERDES1G(8) PHY_MODE_SGMII>;
+ };
+ };
+};
/dts-v1/;
#include "mscc,jr2.dtsi"
+#include <dt-bindings/mscc/jr2_data.h>
/ {
model = "Jaguar2 Cu48 PCB111 Reference Board";
&spi0 {
status = "okay";
spi-flash@0 {
- compatible = "spi-flash";
+ compatible = "jedec,spi-nor";
spi-max-frequency = <18000000>; /* input clock */
reg = <0>; /* CS0 */
};
sgpio-ports = <0xff000000>;
gpio-ranges = <&sgpio2 0 0 96>;
};
+
+&mdio1 {
+ status = "okay";
+
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+ phy2: ethernet-phy@2 {
+ reg = <2>;
+ };
+ phy3: ethernet-phy@3 {
+ reg = <3>;
+ };
+ phy4: ethernet-phy@4 {
+ reg = <4>;
+ };
+ phy5: ethernet-phy@5 {
+ reg = <5>;
+ };
+ phy6: ethernet-phy@6 {
+ reg = <6>;
+ };
+ phy7: ethernet-phy@7 {
+ reg = <7>;
+ };
+ phy8: ethernet-phy@8 {
+ reg = <8>;
+ };
+ phy9: ethernet-phy@9 {
+ reg = <9>;
+ };
+ phy10: ethernet-phy@10 {
+ reg = <10>;
+ };
+ phy11: ethernet-phy@11 {
+ reg = <11>;
+ };
+ phy12: ethernet-phy@12 {
+ reg = <12>;
+ };
+ phy13: ethernet-phy@13 {
+ reg = <13>;
+ };
+ phy14: ethernet-phy@14 {
+ reg = <14>;
+ };
+ phy15: ethernet-phy@15 {
+ reg = <15>;
+ };
+ phy16: ethernet-phy@16 {
+ reg = <16>;
+ };
+ phy17: ethernet-phy@17 {
+ reg = <17>;
+ };
+ phy18: ethernet-phy@18 {
+ reg = <18>;
+ };
+ phy19: ethernet-phy@19 {
+ reg = <19>;
+ };
+ phy20: ethernet-phy@20 {
+ reg = <20>;
+ };
+ phy21: ethernet-phy@21 {
+ reg = <21>;
+ };
+ phy22: ethernet-phy@22 {
+ reg = <22>;
+ };
+ phy23: ethernet-phy@23 {
+ reg = <23>;
+ };
+};
+
+&mdio2 {
+ status = "okay";
+
+ phy24: ethernet-phy@24 {
+ reg = <0>;
+ };
+ phy25: ethernet-phy@25 {
+ reg = <1>;
+ };
+ phy26: ethernet-phy@26 {
+ reg = <2>;
+ };
+ phy27: ethernet-phy@27 {
+ reg = <3>;
+ };
+ phy28: ethernet-phy@28 {
+ reg = <4>;
+ };
+ phy29: ethernet-phy@29 {
+ reg = <5>;
+ };
+ phy30: ethernet-phy@30 {
+ reg = <6>;
+ };
+ phy31: ethernet-phy@31 {
+ reg = <7>;
+ };
+ phy32: ethernet-phy@32 {
+ reg = <8>;
+ };
+ phy33: ethernet-phy@33 {
+ reg = <9>;
+ };
+ phy34: ethernet-phy@34 {
+ reg = <10>;
+ };
+ phy35: ethernet-phy@35 {
+ reg = <11>;
+ };
+ phy36: ethernet-phy@36 {
+ reg = <12>;
+ };
+ phy37: ethernet-phy@37 {
+ reg = <13>;
+ };
+ phy38: ethernet-phy@38 {
+ reg = <14>;
+ };
+ phy39: ethernet-phy@39 {
+ reg = <15>;
+ };
+ phy40: ethernet-phy@40 {
+ reg = <16>;
+ };
+ phy41: ethernet-phy@41 {
+ reg = <17>;
+ };
+ phy42: ethernet-phy@42 {
+ reg = <18>;
+ };
+ phy43: ethernet-phy@43 {
+ reg = <19>;
+ };
+ phy44: ethernet-phy@44 {
+ reg = <20>;
+ };
+ phy45: ethernet-phy@45 {
+ reg = <21>;
+ };
+ phy46: ethernet-phy@46 {
+ reg = <22>;
+ };
+ phy47: ethernet-phy@47 {
+ reg = <23>;
+ };
+};
+
+&switch {
+ ethernet-ports {
+ port0: port@0 {
+ reg = <0>;
+ phy-handle = <&phy0>;
+ phys = <&serdes_hsio 0 SERDES6G(4) PHY_MODE_QSGMII>;
+ };
+ port1: port@1 {
+ reg = <1>;
+ phy-handle = <&phy1>;
+ phys = <&serdes_hsio 1 0xff PHY_MODE_QSGMII>;
+ };
+ port2: port@2 {
+ reg = <2>;
+ phy-handle = <&phy2>;
+ phys = <&serdes_hsio 2 0xff PHY_MODE_QSGMII>;
+ };
+ port3: port@3 {
+ reg = <3>;
+ phy-handle = <&phy3>;
+ phys = <&serdes_hsio 3 0xff PHY_MODE_QSGMII>;
+ };
+ port4: port@4 {
+ reg = <4>;
+ phy-handle = <&phy4>;
+ phys = <&serdes_hsio 4 SERDES6G(5) PHY_MODE_QSGMII>;
+ };
+ port5: port@5 {
+ reg = <5>;
+ phy-handle = <&phy5>;
+ phys = <&serdes_hsio 5 0xff PHY_MODE_QSGMII>;
+ };
+ port6: port@6 {
+ reg = <6>;
+ phy-handle = <&phy6>;
+ phys = <&serdes_hsio 6 0xff PHY_MODE_QSGMII>;
+ };
+ port7: port@7 {
+ reg = <7>;
+ phy-handle = <&phy7>;
+ phys = <&serdes_hsio 7 0xff PHY_MODE_QSGMII>;
+ };
+ port8: port@8 {
+ reg = <8>;
+ phy-handle = <&phy8>;
+ phys = <&serdes_hsio 8 SERDES6G(6) PHY_MODE_QSGMII>;
+ };
+ port9: port@9 {
+ reg = <9>;
+ phy-handle = <&phy9>;
+ phys = <&serdes_hsio 9 0xff PHY_MODE_QSGMII>;
+ };
+ port10: port@10 {
+ reg = <10>;
+ phy-handle = <&phy10>;
+ phys = <&serdes_hsio 10 0xff PHY_MODE_QSGMII>;
+ };
+ port11: port@11 {
+ reg = <11>;
+ phy-handle = <&phy11>;
+ phys = <&serdes_hsio 11 0xff PHY_MODE_QSGMII>;
+ };
+ port12: port@12 {
+ reg = <12>;
+ phy-handle = <&phy12>;
+ phys = <&serdes_hsio 12 SERDES6G(7) PHY_MODE_QSGMII>;
+ };
+ port13: port@13 {
+ reg = <13>;
+ phy-handle = <&phy13>;
+ phys = <&serdes_hsio 13 0xff PHY_MODE_QSGMII>;
+ };
+ port14: port@14 {
+ reg = <14>;
+ phy-handle = <&phy14>;
+ phys = <&serdes_hsio 14 0xff PHY_MODE_QSGMII>;
+ };
+ port15: port@15 {
+ reg = <15>;
+ phy-handle = <&phy15>;
+ phys = <&serdes_hsio 15 0xff PHY_MODE_QSGMII>;
+ };
+ port16: port@16 {
+ reg = <16>;
+ phy-handle = <&phy16>;
+ phys = <&serdes_hsio 16 SERDES6G(8) PHY_MODE_QSGMII>;
+ };
+ port17: port@17 {
+ reg = <17>;
+ phy-handle = <&phy17>;
+ phys = <&serdes_hsio 17 0xff PHY_MODE_QSGMII>;
+ };
+ port18: port@18 {
+ reg = <18>;
+ phy-handle = <&phy18>;
+ phys = <&serdes_hsio 18 0xff PHY_MODE_QSGMII>;
+ };
+ port19: port@19 {
+ reg = <19>;
+ phy-handle = <&phy19>;
+ phys = <&serdes_hsio 19 0xff PHY_MODE_QSGMII>;
+ };
+ port20: port@20 {
+ reg = <20>;
+ phy-handle = <&phy20>;
+ phys = <&serdes_hsio 20 SERDES6G(9) PHY_MODE_QSGMII>;
+ };
+ port21: port@21 {
+ reg = <21>;
+ phy-handle = <&phy21>;
+ phys = <&serdes_hsio 21 0xff PHY_MODE_QSGMII>;
+ };
+ port22: port@22 {
+ reg = <22>;
+ phy-handle = <&phy22>;
+ phys = <&serdes_hsio 22 0xff PHY_MODE_QSGMII>;
+ };
+ port23: port@23 {
+ reg = <23>;
+ phy-handle = <&phy23>;
+ phys = <&serdes_hsio 23 0xff PHY_MODE_QSGMII>;
+ };
+ port24: port@24 {
+ reg = <24>;
+ phy-handle = <&phy24>;
+ phys = <&serdes_hsio 24 SERDES6G(10) PHY_MODE_QSGMII>;
+ };
+ port25: port@25 {
+ reg = <25>;
+ phy-handle = <&phy25>;
+ phys = <&serdes_hsio 25 0xff PHY_MODE_QSGMII>;
+ };
+ port26: port@26 {
+ reg = <26>;
+ phy-handle = <&phy26>;
+ phys = <&serdes_hsio 26 0xff PHY_MODE_QSGMII>;
+ };
+ port27: port@27 {
+ reg = <27>;
+ phy-handle = <&phy27>;
+ phys = <&serdes_hsio 27 0xff PHY_MODE_QSGMII>;
+ };
+ port28: port@28 {
+ reg = <28>;
+ phy-handle = <&phy28>;
+ phys = <&serdes_hsio 28 SERDES6G(11) PHY_MODE_QSGMII>;
+ };
+ port29: port@29 {
+ reg = <29>;
+ phy-handle = <&phy29>;
+ phys = <&serdes_hsio 29 0xff PHY_MODE_QSGMII>;
+ };
+ port30: port@30 {
+ reg = <30>;
+ phy-handle = <&phy30>;
+ phys = <&serdes_hsio 30 0xff PHY_MODE_QSGMII>;
+ };
+ port31: port@31 {
+ reg = <31>;
+ phy-handle = <&phy31>;
+ phys = <&serdes_hsio 31 0xff PHY_MODE_QSGMII>;
+ };
+ port32: port@32 {
+ reg = <32>;
+ phy-handle = <&phy32>;
+ phys = <&serdes_hsio 32 SERDES6G(12) PHY_MODE_QSGMII>;
+ };
+ port33: port@33 {
+ reg = <33>;
+ phy-handle = <&phy33>;
+ phys = <&serdes_hsio 33 0xff PHY_MODE_QSGMII>;
+ };
+ port34: port@34 {
+ reg = <34>;
+ phy-handle = <&phy34>;
+ phys = <&serdes_hsio 34 0xff PHY_MODE_QSGMII>;
+ };
+ port35: port@35 {
+ reg = <35>;
+ phy-handle = <&phy35>;
+ phys = <&serdes_hsio 35 0xff PHY_MODE_QSGMII>;
+ };
+ port36: port@36 {
+ reg = <36>;
+ phy-handle = <&phy36>;
+ phys = <&serdes_hsio 36 SERDES6G(13) PHY_MODE_QSGMII>;
+ };
+ port37: port@37 {
+ reg = <37>;
+ phy-handle = <&phy37>;
+ phys = <&serdes_hsio 37 0xff PHY_MODE_QSGMII>;
+ };
+ port38: port@38 {
+ reg = <38>;
+ phy-handle = <&phy38>;
+ phys = <&serdes_hsio 38 0xff PHY_MODE_QSGMII>;
+ };
+ port39: port@39 {
+ reg = <39>;
+ phy-handle = <&phy39>;
+ phys = <&serdes_hsio 39 0xff PHY_MODE_QSGMII>;
+ };
+ port40: port@40 {
+ reg = <40>;
+ phy-handle = <&phy40>;
+ phys = <&serdes_hsio 40 SERDES6G(14) PHY_MODE_QSGMII>;
+ };
+ port41: port@41 {
+ reg = <41>;
+ phy-handle = <&phy41>;
+ phys = <&serdes_hsio 41 0xff PHY_MODE_QSGMII>;
+ };
+ port42: port@42 {
+ reg = <42>;
+ phy-handle = <&phy42>;
+ phys = <&serdes_hsio 42 0xff PHY_MODE_QSGMII>;
+ };
+ port43: port@43 {
+ reg = <43>;
+ phy-handle = <&phy43>;
+ phys = <&serdes_hsio 43 0xff PHY_MODE_QSGMII>;
+ };
+ port44: port@44 {
+ reg = <44>;
+ phy-handle = <&phy44>;
+ phys = <&serdes_hsio 44 SERDES6G(15) PHY_MODE_QSGMII>;
+ };
+ port45: port@45 {
+ reg = <45>;
+ phy-handle = <&phy45>;
+ phys = <&serdes_hsio 45 0xff PHY_MODE_QSGMII>;
+ };
+ port46: port@46 {
+ reg = <46>;
+ phy-handle = <&phy46>;
+ phys = <&serdes_hsio 46 0xff PHY_MODE_QSGMII>;
+ };
+ port47: port@47 {
+ reg = <47>;
+ phy-handle = <&phy47>;
+ phys = <&serdes_hsio 47 0xff PHY_MODE_QSGMII>;
+ };
+ };
+};
/dts-v1/;
#include "mscc,jr2.dtsi"
+#include <dt-bindings/mscc/jr2_data.h>
/ {
model = "Serval2 NID PCB112 Reference Board";
&spi0 {
status = "okay";
spi-flash@0 {
- compatible = "spi-flash";
+ compatible = "jedec,spi-nor";
spi-max-frequency = <18000000>; /* input clock */
reg = <0>; /* CS0 */
};
status = "okay";
sgpio-ports = <0x3fe0ffff>;
};
+
+&mdio0 {
+ status = "okay";
+
+ phy16: ethernet-phy@16 {
+ reg = <16>;
+ };
+ phy17: ethernet-phy@17 {
+ reg = <17>;
+ };
+ phy18: ethernet-phy@18 {
+ reg = <18>;
+ };
+ phy19: ethernet-phy@19 {
+ reg = <19>;
+ };
+};
+
+&switch {
+ ethernet-ports {
+
+ port0: port@0 {
+ reg = <24>;
+ phy-handle = <&phy16>;
+ phys = <&serdes_hsio 24 SERDES6G(0) PHY_MODE_SGMII>;
+ };
+ port1: port@1 {
+ reg = <25>;
+ phy-handle = <&phy17>;
+ phys = <&serdes_hsio 25 SERDES6G(1) PHY_MODE_SGMII>;
+ };
+ port2: port@2 {
+ reg = <26>;
+ phy-handle = <&phy18>;
+ phys = <&serdes_hsio 26 SERDES6G(2) PHY_MODE_SGMII>;
+ };
+ port3: port@3 {
+ reg = <27>;
+ phy-handle = <&phy19>;
+ phys = <&serdes_hsio 27 SERDES6G(3) PHY_MODE_SGMII>;
+ };
+ };
+};
&spi0 {
status = "okay";
spi-flash@0 {
- compatible = "spi-flash";
+ compatible = "jedec,spi-nor";
spi-max-frequency = <18000000>; /* input clock */
reg = <0>; /* CS0 */
spi-cs-high;
status = "okay";
sgpio-ports = <0x0000fe7f>;
};
+
+&mdio0 {
+ status = "okay";
+
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&switch {
+ ethernet-ports {
+
+ port0: port@0 {
+ reg = <0>;
+ phy-handle = <&phy0>;
+ };
+ port1: port@1 {
+ reg = <1>;
+ phy-handle = <&phy1>;
+ };
+ };
+};
compatible = "denx,u-boot-probe-test";
first-syscon = <&syscon0>;
second-sys-ctrl = <&another_system_controller>;
+ third-syscon = <&syscon2>;
};
};
cs-gpios = <0>, <&gpio_a 0>;
spi.bin@0 {
reg = <0>;
- compatible = "spansion,m25p16", "spi-flash";
+ compatible = "spansion,m25p16", "jedec,spi-nor";
spi-max-frequency = <40000000>;
sandbox,filename = "spi.bin";
};
0x38 8>;
};
- syscon@2 {
+ syscon2: syscon@2 {
compatible = "simple-mfd", "syscon";
reg = <0x40 5
0x48 6
S: Maintained
F: configs/Nintendo_NES_Classic_Edition_defconfig
+OCEANIC 5205 5INMFD BOARD
+S: Maintained
+F: configs/oceanic_5205_5inmfd_defconfig
+
OLIMEX A20-SOM204 BOARD
S: Maintained
F: configs/A20-Olimex-SOM204-EVB-eMMC_defconfig
ORANGEPI LITE2 BOARD
- M: Jagan Teki <jagan@openedev.com>
+ M: Jagan Teki <jagan@amarulasolutions.com>
S: Maintained
F: configs/orangepi_lite2_defconfig
CONFIG_ARM=y
+CONFIG_SYS_THUMB_BUILD=y
CONFIG_ARCH_DAVINCI=y
CONFIG_SYS_TEXT_BASE=0xc1080000
CONFIG_TARGET_DA850EVM=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_SYS_EXTRA_OPTIONS="MAC_ADDR_IN_SPIFLASH"
CONFIG_BOOTDELAY=3
+CONFIG_DEFAULT_FDT_FILE="da850-evm.dtb"
CONFIG_MISC_INIT_R=y
CONFIG_VERSION_VARIABLE=y
# CONFIG_DISPLAY_CPUINFO is not set
CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_SPL_BOARD_INIT=y
CONFIG_SPL_SYS_MALLOC_SIMPLE=y
+CONFIG_SPL_SEPARATE_BSS=y
CONFIG_SPL_SPI_LOAD=y
CONFIG_HUSH_PARSER=y
CONFIG_SYS_PROMPT="U-Boot > "
CONFIG_OF_CONTROL=y
CONFIG_SPL_OF_CONTROL=y
CONFIG_DEFAULT_DEVICE_TREE="da850-evm"
-CONFIG_SPL_OF_PLATDATA=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
- CONFIG_USE_ENV_SPI_MAX_HZ=y
- CONFIG_ENV_SPI_MAX_HZ=0
- CONFIG_USE_ENV_SPI_MODE=y
- CONFIG_ENV_SPI_MODE=0
CONFIG_DM=y
CONFIG_SPL_DM=y
+CONFIG_SPL_DM_SEQ_ALIAS=y
+CONFIG_SPL_OF_TRANSLATE=y
CONFIG_DM_GPIO=y
CONFIG_DA8XX_GPIO=y
CONFIG_DM_I2C=y
CONFIG_CMD_GPIO=y
CONFIG_CMD_SF=y
CONFIG_CMD_SPI=y
-# CONFIG_CMD_NET is not set
+CONFIG_CMD_DHCP=y
+# CONFIG_NET_TFTP_VARS is not set
+# CONFIG_CMD_NFS is not set
+CONFIG_CMD_PING=y
CONFIG_CMD_MTDPARTS=y
CONFIG_MTDIDS_DEFAULT="nor0=spi_flash"
CONFIG_MTDPARTS_DEFAULT="mtdparts=spi_flash:1m(UBoot),256k(Env),256k(Env.bk)"
CONFIG_DTB_RESELECT=y
CONFIG_MULTI_DTB_FIT=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
- CONFIG_USE_ENV_SPI_MAX_HZ=y
- CONFIG_ENV_SPI_MAX_HZ=0
- CONFIG_USE_ENV_SPI_MODE=y
- CONFIG_ENV_SPI_MODE=0
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_CLK=y
CONFIG_DM_GPIO=y
CONFIG_SPI=y
CONFIG_DM_SPI=y
CONFIG_LZMA=y
+CONFIG_MSCC_JR2_SWITCH=y
CONFIG_CMD_GPIO=y
CONFIG_CMD_SF=y
CONFIG_CMD_SPI=y
-# CONFIG_CMD_NET is not set
CONFIG_CMD_MTDPARTS=y
CONFIG_MTDIDS_DEFAULT="nor0=spi_flash"
CONFIG_MTDPARTS_DEFAULT="mtdparts=spi_flash:1m(UBoot),256k(Env),256k(Env.bk)"
CONFIG_DTB_RESELECT=y
CONFIG_MULTI_DTB_FIT=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
- CONFIG_USE_ENV_SPI_MAX_HZ=y
- CONFIG_ENV_SPI_MAX_HZ=0
- CONFIG_USE_ENV_SPI_MODE=y
- CONFIG_ENV_SPI_MODE=0
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_CLK=y
CONFIG_DM_GPIO=y
CONFIG_SPI=y
CONFIG_DM_SPI=y
CONFIG_LZMA=y
+CONFIG_CMD_DHCP=y
+# CONFIG_NET_TFTP_VARS is not set
+# CONFIG_CMD_NFS is not set
+CONFIG_CMD_PING=y
+CONFIG_MSCC_SERVALT_SWITCH=y
- alias jagan Jagan Teki <jagan@openedev.com>
+ alias jagan Jagan Teki <jagan@amarulasolutions.com>
alias at91 uboot, abiessmann
alias davinci ti
alias imx uboot, sbabic
-alias kirkwood uboot, prafulla, luka, stroese
+alias kirkwood uboot, stroese
alias omap ti
alias pxa uboot, marex
alias rmobile uboot, iwamatsu
COMPAT(SAMSUNG_EXYNOS_TMU, "samsung,exynos-tmu"),
COMPAT(SAMSUNG_EXYNOS_MIPI_DSI, "samsung,exynos-mipi-dsi"),
COMPAT(SAMSUNG_EXYNOS_DWMMC, "samsung,exynos-dwmmc"),
- COMPAT(GENERIC_SPI_FLASH, "spi-flash"),
+ COMPAT(GENERIC_SPI_FLASH, "jedec,spi-nor"),
COMPAT(SAMSUNG_EXYNOS_SYSMMU, "samsung,sysmmu-v3.3"),
COMPAT(INTEL_MICROCODE, "intel,microcode"),
COMPAT(INTEL_QRK_MRC, "intel,quark-mrc"),
}
#endif
+int fdtdec_set_phandle(void *blob, int node, uint32_t phandle)
+{
+ fdt32_t value = cpu_to_fdt32(phandle);
+
+ return fdt_setprop(blob, node, "phandle", &value, sizeof(value));
+}
+
+static int fdtdec_init_reserved_memory(void *blob)
+{
+ int na, ns, node, err;
+ fdt32_t value;
+
+ /* inherit #address-cells and #size-cells from the root node */
+ na = fdt_address_cells(blob, 0);
+ ns = fdt_size_cells(blob, 0);
+
+ node = fdt_add_subnode(blob, 0, "reserved-memory");
+ if (node < 0)
+ return node;
+
+ err = fdt_setprop(blob, node, "ranges", NULL, 0);
+ if (err < 0)
+ return err;
+
+ value = cpu_to_fdt32(ns);
+
+ err = fdt_setprop(blob, node, "#size-cells", &value, sizeof(value));
+ if (err < 0)
+ return err;
+
+ value = cpu_to_fdt32(na);
+
+ err = fdt_setprop(blob, node, "#address-cells", &value, sizeof(value));
+ if (err < 0)
+ return err;
+
+ return node;
+}
+
+int fdtdec_add_reserved_memory(void *blob, const char *basename,
+ const struct fdt_memory *carveout,
+ uint32_t *phandlep)
+{
+ fdt32_t cells[4] = {}, *ptr = cells;
+ uint32_t upper, lower, phandle;
+ int parent, node, na, ns, err;
+ char name[64];
+
+ /* create an empty /reserved-memory node if one doesn't exist */
+ parent = fdt_path_offset(blob, "/reserved-memory");
+ if (parent < 0) {
+ parent = fdtdec_init_reserved_memory(blob);
+ if (parent < 0)
+ return parent;
+ }
+
+ /* only 1 or 2 #address-cells and #size-cells are supported */
+ na = fdt_address_cells(blob, parent);
+ if (na < 1 || na > 2)
+ return -FDT_ERR_BADNCELLS;
+
+ ns = fdt_size_cells(blob, parent);
+ if (ns < 1 || ns > 2)
+ return -FDT_ERR_BADNCELLS;
+
+ /* find a matching node and return the phandle to that */
+ fdt_for_each_subnode(node, blob, parent) {
+ const char *name = fdt_get_name(blob, node, NULL);
+ phys_addr_t addr, size;
+
+ addr = fdtdec_get_addr_size(blob, node, "reg", &size);
+ if (addr == FDT_ADDR_T_NONE) {
+ debug("failed to read address/size for %s\n", name);
+ continue;
+ }
+
+ if (addr == carveout->start && (addr + size) == carveout->end) {
+ *phandlep = fdt_get_phandle(blob, node);
+ return 0;
+ }
+ }
+
+ /*
+ * Unpack the start address and generate the name of the new node
+ * base on the basename and the unit-address.
+ */
+ lower = fdt_addr_unpack(carveout->start, &upper);
+
+ if (na > 1 && upper > 0)
+ snprintf(name, sizeof(name), "%s@%x,%x", basename, upper,
+ lower);
+ else {
+ if (upper > 0) {
+ debug("address %08x:%08x exceeds addressable space\n",
+ upper, lower);
+ return -FDT_ERR_BADVALUE;
+ }
+
+ snprintf(name, sizeof(name), "%s@%x", basename, lower);
+ }
+
+ node = fdt_add_subnode(blob, parent, name);
+ if (node < 0)
+ return node;
+
+ err = fdt_generate_phandle(blob, &phandle);
+ if (err < 0)
+ return err;
+
+ err = fdtdec_set_phandle(blob, node, phandle);
+ if (err < 0)
+ return err;
+
+ /* store one or two address cells */
+ if (na > 1)
+ *ptr++ = cpu_to_fdt32(upper);
+
+ *ptr++ = cpu_to_fdt32(lower);
+
+ /* store one or two size cells */
+ lower = fdt_size_unpack(carveout->end - carveout->start + 1, &upper);
+
+ if (ns > 1)
+ *ptr++ = cpu_to_fdt32(upper);
+
+ *ptr++ = cpu_to_fdt32(lower);
+
+ err = fdt_setprop(blob, node, "reg", cells, (na + ns) * sizeof(*cells));
+ if (err < 0)
+ return err;
+
+ /* return the phandle for the new node for the caller to use */
+ if (phandlep)
+ *phandlep = phandle;
+
+ return 0;
+}
+
+int fdtdec_get_carveout(const void *blob, const char *node, const char *name,
+ unsigned int index, struct fdt_memory *carveout)
+{
+ const fdt32_t *prop;
+ uint32_t phandle;
+ int offset, len;
+ fdt_size_t size;
+
+ offset = fdt_path_offset(blob, node);
+ if (offset < 0)
+ return offset;
+
+ prop = fdt_getprop(blob, offset, name, &len);
+ if (!prop) {
+ debug("failed to get %s for %s\n", name, node);
+ return -FDT_ERR_NOTFOUND;
+ }
+
+ if ((len % sizeof(phandle)) != 0) {
+ debug("invalid phandle property\n");
+ return -FDT_ERR_BADPHANDLE;
+ }
+
+ if (len < (sizeof(phandle) * (index + 1))) {
+ debug("invalid phandle index\n");
+ return -FDT_ERR_BADPHANDLE;
+ }
+
+ phandle = fdt32_to_cpu(prop[index]);
+
+ offset = fdt_node_offset_by_phandle(blob, phandle);
+ if (offset < 0) {
+ debug("failed to find node for phandle %u\n", phandle);
+ return offset;
+ }
+
+ carveout->start = fdtdec_get_addr_size_auto_noparent(blob, offset,
+ "reg", 0, &size,
+ true);
+ if (carveout->start == FDT_ADDR_T_NONE) {
+ debug("failed to read address/size from \"reg\" property\n");
+ return -FDT_ERR_NOTFOUND;
+ }
+
+ carveout->end = carveout->start + size - 1;
+
+ return 0;
+}
+
+int fdtdec_set_carveout(void *blob, const char *node, const char *prop_name,
+ unsigned int index, const char *name,
+ const struct fdt_memory *carveout)
+{
+ uint32_t phandle;
+ int err, offset;
+ fdt32_t value;
+
+ /* XXX implement support for multiple phandles */
+ if (index > 0) {
+ debug("invalid index %u\n", index);
+ return -FDT_ERR_BADOFFSET;
+ }
+
+ err = fdtdec_add_reserved_memory(blob, name, carveout, &phandle);
+ if (err < 0) {
+ debug("failed to add reserved memory: %d\n", err);
+ return err;
+ }
+
+ offset = fdt_path_offset(blob, node);
+ if (offset < 0) {
+ debug("failed to find offset for node %s: %d\n", node, offset);
+ return offset;
+ }
+
+ value = cpu_to_fdt32(phandle);
+
+ err = fdt_setprop(blob, offset, prop_name, &value, sizeof(value));
+ if (err < 0) {
+ debug("failed to set %s property for node %s: %d\n", prop_name,
+ node, err);
+ return err;
+ }
+
+ return 0;
+}
+
int fdtdec_setup(void)
{
#if CONFIG_IS_ENABLED(OF_CONTROL)
projects / J-u-boot.git / commitdiff