config SYS_ARCH
default "x86"
-config USE_PRIVATE_LIBGCC
- default y
-
-config SYS_VSNPRINTF
- default y
-
choice
prompt "Mainboard vendor"
- default VENDOR_COREBOOT
+ default VENDOR_EMULATION
+
+config VENDOR_CONGATEC
+ bool "congatec"
config VENDOR_COREBOOT
bool "coreboot"
+config VENDOR_EFI
+ bool "efi"
+
+config VENDOR_EMULATION
+ bool "emulation"
+
config VENDOR_GOOGLE
bool "Google"
endchoice
# board-specific options below
+source "board/congatec/Kconfig"
source "board/coreboot/Kconfig"
+source "board/efi/Kconfig"
+source "board/emulation/Kconfig"
source "board/google/Kconfig"
source "board/intel/Kconfig"
# platform-specific options below
source "arch/x86/cpu/baytrail/Kconfig"
+source "arch/x86/cpu/broadwell/Kconfig"
source "arch/x86/cpu/coreboot/Kconfig"
source "arch/x86/cpu/ivybridge/Kconfig"
+source "arch/x86/cpu/qemu/Kconfig"
source "arch/x86/cpu/quark/Kconfig"
source "arch/x86/cpu/queensbay/Kconfig"
# architecture-specific options below
+config AHCI
+ default y
+
config SYS_MALLOC_F_LEN
default 0x800
bool
default n
+config RESET_SEG_START
+ hex
+ depends on X86_RESET_VECTOR
+ default 0xffff0000
+
+config RESET_SEG_SIZE
+ hex
+ depends on X86_RESET_VECTOR
+ default 0x10000
+
+config RESET_VEC_LOC
+ hex
+ depends on X86_RESET_VECTOR
+ default 0xfffffff0
+
config SYS_X86_START16
hex
depends on X86_RESET_VECTOR
to work correctly. It is not exhaustive but can save time by
detecting obvious failures.
-config MARK_GRAPHICS_MEM_WRCOMB
- bool "Mark graphics memory as write-combining"
- default n
- help
- The graphics performance may increase if the graphics
- memory is set as write-combining cache type. This option
- enables marking the graphics memory as write-combining.
-
-menu "Display"
-
-config FRAMEBUFFER_SET_VESA_MODE
- prompt "Set framebuffer graphics resolution"
- bool
- help
- Set VESA/native framebuffer mode (needed for bootsplash and graphical framebuffer console)
-
-choice
- prompt "framebuffer graphics resolution"
- default FRAMEBUFFER_VESA_MODE_117
- depends on FRAMEBUFFER_SET_VESA_MODE
- help
- This option sets the resolution used for the coreboot framebuffer (and
- bootsplash screen).
-
-config FRAMEBUFFER_VESA_MODE_100
- bool "640x400 256-color"
-
-config FRAMEBUFFER_VESA_MODE_101
- bool "640x480 256-color"
-
-config FRAMEBUFFER_VESA_MODE_102
- bool "800x600 16-color"
-
-config FRAMEBUFFER_VESA_MODE_103
- bool "800x600 256-color"
-
-config FRAMEBUFFER_VESA_MODE_104
- bool "1024x768 16-color"
-
-config FRAMEBUFFER_VESA_MODE_105
- bool "1024x7686 256-color"
-
-config FRAMEBUFFER_VESA_MODE_106
- bool "1280x1024 16-color"
-
-config FRAMEBUFFER_VESA_MODE_107
- bool "1280x1024 256-color"
-
-config FRAMEBUFFER_VESA_MODE_108
- bool "80x60 text"
-
-config FRAMEBUFFER_VESA_MODE_109
- bool "132x25 text"
-
-config FRAMEBUFFER_VESA_MODE_10A
- bool "132x43 text"
-
-config FRAMEBUFFER_VESA_MODE_10B
- bool "132x50 text"
-
-config FRAMEBUFFER_VESA_MODE_10C
- bool "132x60 text"
-
-config FRAMEBUFFER_VESA_MODE_10D
- bool "320x200 32k-color (1:5:5:5)"
-
-config FRAMEBUFFER_VESA_MODE_10E
- bool "320x200 64k-color (5:6:5)"
-
-config FRAMEBUFFER_VESA_MODE_10F
- bool "320x200 16.8M-color (8:8:8)"
-
-config FRAMEBUFFER_VESA_MODE_110
- bool "640x480 32k-color (1:5:5:5)"
-
-config FRAMEBUFFER_VESA_MODE_111
- bool "640x480 64k-color (5:6:5)"
-
-config FRAMEBUFFER_VESA_MODE_112
- bool "640x480 16.8M-color (8:8:8)"
-
-config FRAMEBUFFER_VESA_MODE_113
- bool "800x600 32k-color (1:5:5:5)"
-
-config FRAMEBUFFER_VESA_MODE_114
- bool "800x600 64k-color (5:6:5)"
-
-config FRAMEBUFFER_VESA_MODE_115
- bool "800x600 16.8M-color (8:8:8)"
-
-config FRAMEBUFFER_VESA_MODE_116
- bool "1024x768 32k-color (1:5:5:5)"
-
-config FRAMEBUFFER_VESA_MODE_117
- bool "1024x768 64k-color (5:6:5)"
-
-config FRAMEBUFFER_VESA_MODE_118
- bool "1024x768 16.8M-color (8:8:8)"
-
-config FRAMEBUFFER_VESA_MODE_119
- bool "1280x1024 32k-color (1:5:5:5)"
-
-config FRAMEBUFFER_VESA_MODE_11A
- bool "1280x1024 64k-color (5:6:5)"
-
-config FRAMEBUFFER_VESA_MODE_11B
- bool "1280x1024 16.8M-color (8:8:8)"
-
-config FRAMEBUFFER_VESA_MODE_USER
- bool "Manually select VESA mode"
-
-endchoice
-
-# Map the config names to an integer (KB).
-config FRAMEBUFFER_VESA_MODE
- prompt "VESA mode" if FRAMEBUFFER_VESA_MODE_USER
- hex
- default 0x100 if FRAMEBUFFER_VESA_MODE_100
- default 0x101 if FRAMEBUFFER_VESA_MODE_101
- default 0x102 if FRAMEBUFFER_VESA_MODE_102
- default 0x103 if FRAMEBUFFER_VESA_MODE_103
- default 0x104 if FRAMEBUFFER_VESA_MODE_104
- default 0x105 if FRAMEBUFFER_VESA_MODE_105
- default 0x106 if FRAMEBUFFER_VESA_MODE_106
- default 0x107 if FRAMEBUFFER_VESA_MODE_107
- default 0x108 if FRAMEBUFFER_VESA_MODE_108
- default 0x109 if FRAMEBUFFER_VESA_MODE_109
- default 0x10A if FRAMEBUFFER_VESA_MODE_10A
- default 0x10B if FRAMEBUFFER_VESA_MODE_10B
- default 0x10C if FRAMEBUFFER_VESA_MODE_10C
- default 0x10D if FRAMEBUFFER_VESA_MODE_10D
- default 0x10E if FRAMEBUFFER_VESA_MODE_10E
- default 0x10F if FRAMEBUFFER_VESA_MODE_10F
- default 0x110 if FRAMEBUFFER_VESA_MODE_110
- default 0x111 if FRAMEBUFFER_VESA_MODE_111
- default 0x112 if FRAMEBUFFER_VESA_MODE_112
- default 0x113 if FRAMEBUFFER_VESA_MODE_113
- default 0x114 if FRAMEBUFFER_VESA_MODE_114
- default 0x115 if FRAMEBUFFER_VESA_MODE_115
- default 0x116 if FRAMEBUFFER_VESA_MODE_116
- default 0x117 if FRAMEBUFFER_VESA_MODE_117
- default 0x118 if FRAMEBUFFER_VESA_MODE_118
- default 0x119 if FRAMEBUFFER_VESA_MODE_119
- default 0x11A if FRAMEBUFFER_VESA_MODE_11A
- default 0x11B if FRAMEBUFFER_VESA_MODE_11B
- default 0x117 if FRAMEBUFFER_VESA_MODE_USER
-
-endmenu
-
config HAVE_FSP
bool "Add an Firmware Support Package binary"
+ depends on !EFI
help
Select this option to add an Firmware Support Package binary to
the resulting U-Boot image. It is a binary blob which U-Boot uses
config FSP_TEMP_RAM_ADDR
hex
+ depends on HAVE_FSP
default 0x2000000
help
- Stack top address which is used in FspInit after DRAM is ready and
+ Stack top address which is used in fsp_init() after DRAM is ready and
CAR is disabled.
-config MAX_CPUS
- int "Maximum number of CPUs permitted"
- default 4
+config FSP_SYS_MALLOC_F_LEN
+ hex
+ depends on HAVE_FSP
+ default 0x100000
+ help
+ Additional size of malloc() pool before relocation.
+
+config FSP_USE_UPD
+ bool
+ depends on HAVE_FSP
+ default y
+ help
+ Most FSPs use UPD data region for some FSP customization. But there
+ are still some FSPs that might not even have UPD. For such FSPs,
+ override this to n in their platform Kconfig files.
+
+config FSP_BROKEN_HOB
+ bool
+ depends on HAVE_FSP
+ help
+ Indicate some buggy FSPs that does not report memory used by FSP
+ itself as reserved in the resource descriptor HOB. Select this to
+ tell U-Boot to do some additional work to ensure U-Boot relocation
+ do not overwrite the important boot service data which is used by
+ FSP, otherwise the subsequent call to fsp_notify() will fail.
+
+config ENABLE_MRC_CACHE
+ bool "Enable MRC cache"
+ depends on !EFI && !SYS_COREBOOT
+ help
+ Enable this feature to cause MRC data to be cached in NV storage
+ to be used for speeding up boot time on future reboots and/or
+ power cycles.
+
+ For platforms that use Intel FSP for the memory initialization,
+ please check FSP output HOB via U-Boot command 'fsp hob' to see
+ if there is FSP_NON_VOLATILE_STORAGE_HOB_GUID (asm/fsp/fsp_hob.h).
+ If such GUID does not exist, MRC cache is not avaiable on such
+ platform (eg: Intel Queensbay), which means selecting this option
+ here does not make any difference.
+
+config HAVE_MRC
+ bool "Add a System Agent binary"
+ depends on !HAVE_FSP
+ help
+ Select this option to add a System Agent binary to
+ the resulting U-Boot image. MRC stands for Memory Reference Code.
+ It is a binary blob which U-Boot uses to set up SDRAM.
+
+ Note: Without this binary U-Boot will not be able to set up its
+ SDRAM so will not boot.
+
+config CACHE_MRC_BIN
+ bool
+ depends on HAVE_MRC
+ default n
+ help
+ Enable caching for the memory reference code binary. This uses an
+ MTRR (memory type range register) to turn on caching for the section
+ of SPI flash that contains the memory reference code. This makes
+ SDRAM init run faster.
+
+config CACHE_MRC_SIZE_KB
+ int
+ depends on HAVE_MRC
+ default 512
+ help
+ Sets the size of the cached area for the memory reference code.
+ This ends at the end of SPI flash (address 0xffffffff) and is
+ measured in KB. Typically this is set to 512, providing for 0.5MB
+ of cached space.
+
+config DCACHE_RAM_BASE
+ hex
+ depends on HAVE_MRC
+ help
+ Sets the base of the data cache area in memory space. This is the
+ start address of the cache-as-RAM (CAR) area and the address varies
+ depending on the CPU. Once CAR is set up, read/write memory becomes
+ available at this address and can be used temporarily until SDRAM
+ is working.
+
+config DCACHE_RAM_SIZE
+ hex
+ depends on HAVE_MRC
+ default 0x40000
+ help
+ Sets the total size of the data cache area in memory space. This
+ sets the size of the cache-as-RAM (CAR) area. Note that much of the
+ CAR space is required by the MRC. The CAR space available to U-Boot
+ is normally at the start and typically extends to 1/4 or 1/2 of the
+ available size.
+
+config DCACHE_RAM_MRC_VAR_SIZE
+ hex
+ depends on HAVE_MRC
+ help
+ This is the amount of CAR (Cache as RAM) reserved for use by the
+ memory reference code. This depends on the implementation of the
+ memory reference code and must be set correctly or the board will
+ not boot.
+
+config HAVE_REFCODE
+ bool "Add a Reference Code binary"
help
- When using multi-CPU chips it is possible for U-Boot to start up
- more than one CPU. The stack memory used by all of these CPUs is
- pre-allocated so at present U-Boot wants to know the maximum
- number of CPUs that may be present. Set this to at least as high
- as the number of CPUs in your system (it uses about 4KB of RAM for
- each CPU).
+ Select this option to add a Reference Code binary to the resulting
+ U-Boot image. This is an Intel binary blob that handles system
+ initialisation, in this case the PCH and System Agent.
+
+ Note: Without this binary (on platforms that need it such as
+ broadwell) U-Boot will be missing some critical setup steps.
+ Various peripherals may fail to work.
config SMP
bool "Enable Symmetric Multiprocessing"
only one CPU will be enabled regardless of the number of CPUs
available.
+config MAX_CPUS
+ int "Maximum number of CPUs permitted"
+ depends on SMP
+ default 4
+ help
+ When using multi-CPU chips it is possible for U-Boot to start up
+ more than one CPU. The stack memory used by all of these CPUs is
+ pre-allocated so at present U-Boot wants to know the maximum
+ number of CPUs that may be present. Set this to at least as high
+ as the number of CPUs in your system (it uses about 4KB of RAM for
+ each CPU).
+
config AP_STACK_SIZE
hex
+ depends on SMP
default 0x1000
help
Each additional CPU started by U-Boot requires its own stack. This
the memory used by this initialisation process. Typically 4KB is
enough space.
-config TSC_CALIBRATION_BYPASS
- bool "Bypass Time-Stamp Counter (TSC) calibration"
- default n
+config HAVE_VGA_BIOS
+ bool "Add a VGA BIOS image"
help
- By default U-Boot automatically calibrates Time-Stamp Counter (TSC)
- running frequency via Model-Specific Register (MSR) and Programmable
- Interval Timer (PIT). If the calibration does not work on your board,
- select this option and provide a hardcoded TSC running frequency with
- CONFIG_TSC_FREQ_IN_MHZ below.
+ Select this option if you have a VGA BIOS image that you would
+ like to add to your ROM.
- Normally this option should be turned on in a simulation environment
- like qemu.
+config VGA_BIOS_FILE
+ string "VGA BIOS image filename"
+ depends on HAVE_VGA_BIOS
+ default "vga.bin"
+ help
+ The filename of the VGA BIOS image in the board directory.
-config TSC_FREQ_IN_MHZ
- int "Time-Stamp Counter (TSC) running frequency in MHz"
- depends on TSC_CALIBRATION_BYPASS
- default 1000
+config VGA_BIOS_ADDR
+ hex "VGA BIOS image location"
+ depends on HAVE_VGA_BIOS
+ default 0xfff90000
help
- The running frequency in MHz of Time-Stamp Counter (TSC).
+ The location of VGA BIOS image in the SPI flash. For example, base
+ address of 0xfff90000 indicates that the image will be put at offset
+ 0x90000 from the beginning of a 1MB flash device.
menu "System tables"
+ depends on !EFI && !SYS_COREBOOT
config GENERATE_PIRQ_TABLE
bool "Generate a PIRQ table"
For more information, see http://simplefirmware.org
+config GENERATE_MP_TABLE
+ bool "Generate an MP (Multi-Processor) table"
+ default n
+ help
+ Generate an MP (Multi-Processor) table for this board. The MP table
+ provides a way for the operating system to support for symmetric
+ multiprocessing as well as symmetric I/O interrupt handling with
+ the local APIC and I/O APIC.
+
+config GENERATE_ACPI_TABLE
+ bool "Generate an ACPI (Advanced Configuration and Power Interface) table"
+ default n
+ select QFW if QEMU
+ help
+ The Advanced Configuration and Power Interface (ACPI) specification
+ provides an open standard for device configuration and management
+ by the operating system. It defines platform-independent interfaces
+ for configuration and power management monitoring.
+
+config GENERATE_SMBIOS_TABLE
+ bool "Generate an SMBIOS (System Management BIOS) table"
+ default y
+ help
+ The System Management BIOS (SMBIOS) specification addresses how
+ motherboard and system vendors present management information about
+ their products in a standard format by extending the BIOS interface
+ on Intel architecture systems.
+
+ Check http://www.dmtf.org/standards/smbios for details.
+
+config SMBIOS_MANUFACTURER
+ string "SMBIOS Manufacturer"
+ depends on GENERATE_SMBIOS_TABLE
+ default SYS_VENDOR
+ help
+ The board manufacturer to store in SMBIOS structures.
+ Change this to override the default one (CONFIG_SYS_VENDOR).
+
+config SMBIOS_PRODUCT_NAME
+ string "SMBIOS Product Name"
+ depends on GENERATE_SMBIOS_TABLE
+ default SYS_BOARD
+ help
+ The product name to store in SMBIOS structures.
+ Change this to override the default one (CONFIG_SYS_BOARD).
+
endmenu
config MAX_PIRQ_LINKS
assigned to PCI devices - i.e. the memory and prefetch regions, as
passed to pci_set_region().
-config BOOTSTAGE
+config PCIE_ECAM_SIZE
+ hex
+ default 0x10000000
+ help
+ This is the size of memory-mapped address of PCI configuration space,
+ which is only available through the Enhanced Configuration Access
+ Mechanism (ECAM) with PCI Express. Each bus consumes 1 MiB memory,
+ so a default 0x10000000 size covers all of the 256 buses which is the
+ maximum number of PCI buses as defined by the PCI specification.
+
+config I8259_PIC
+ bool
default y
+ help
+ Intel 8259 ISA compatible chipset incorporates two 8259 (master and
+ slave) interrupt controllers. Include this to have U-Boot set up
+ the interrupt correctly.
-config BOOTSTAGE_REPORT
+config I8254_TIMER
+ bool
default y
+ help
+ Intel 8254 timer contains three counters which have fixed uses.
+ Include this to have U-Boot set up the timer correctly.
-config CMD_BOOTSTAGE
+config I8042_KEYB
default y
+config DM_KEYBOARD
+ default y
+
+config SEABIOS
+ bool "Support booting SeaBIOS"
+ help
+ SeaBIOS is an open source implementation of a 16-bit X86 BIOS.
+ It can run in an emulator or natively on X86 hardware with the use
+ of coreboot/U-Boot. By turning on this option, U-Boot prepares
+ all the configuration tables that are necessary to boot SeaBIOS.
+
+ Check http://www.seabios.org/SeaBIOS for details.
+
+config HIGH_TABLE_SIZE
+ hex "Size of configuration tables which reside in high memory"
+ default 0x10000
+ depends on SEABIOS
+ help
+ SeaBIOS itself resides in E seg and F seg, where U-Boot puts all
+ configuration tables like PIRQ/MP/ACPI. To avoid conflicts, U-Boot
+ puts a copy of configuration tables in high memory region which
+ is reserved on the stack before relocation. The region size is
+ determined by this option.
+
+ Increse it if the default size does not fit the board's needs.
+ This is most likely due to a large ACPI DSDT table is used.
+
+source "arch/x86/lib/efi/Kconfig"
+
endmenu
projects / J-u-boot.git / blobdiff