+/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright (C) 2009-2010 Freescale Semiconductor, Inc.
*
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
* High Level Configuration Options
*/
#define CONFIG_E300 1 /* E300 family */
-#define CONFIG_MPC830x 1 /* MPC830x family */
-#define CONFIG_MPC8308 1 /* MPC8308 CPU specific */
-#define CONFIG_MPC8308_P1M 1 /* mpc8308_p1m board specific */
-
-#ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE 0xFC000000
-#endif
/*
* On-board devices
#define CONFIG_TSEC1
#define CONFIG_TSEC2
-/*
- * System Clock Setup
- */
-#define CONFIG_83XX_CLKIN 33333333 /* in Hz */
-#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN
-
-/*
- * Hardware Reset Configuration Word
- * if CLKIN is 66.66MHz, then
- * CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz
- * We choose the A type silicon as default, so the core is 400Mhz.
- */
-#define CONFIG_SYS_HRCW_LOW (\
- HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
- HRCWL_DDR_TO_SCB_CLK_2X1 |\
- HRCWL_SVCOD_DIV_2 |\
- HRCWL_CSB_TO_CLKIN_4X1 |\
- HRCWL_CORE_TO_CSB_3X1)
-/*
- * There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits
- * in 8308's HRCWH according to the manual, but original Freescale's
- * code has them and I've expirienced some problems using the board
- * with BDI3000 attached when I've tried to set these bits to zero
- * (UART doesn't work after the 'reset run' command).
- */
-#define CONFIG_SYS_HRCW_HIGH (\
- HRCWH_PCI_HOST |\
- HRCWH_PCI1_ARBITER_ENABLE |\
- HRCWH_CORE_ENABLE |\
- HRCWH_FROM_0X00000100 |\
- HRCWH_BOOTSEQ_DISABLE |\
- HRCWH_SW_WATCHDOG_DISABLE |\
- HRCWH_ROM_LOC_LOCAL_16BIT |\
- HRCWH_RL_EXT_LEGACY |\
- HRCWH_TSEC1M_IN_MII |\
- HRCWH_TSEC2M_IN_MII |\
- HRCWH_BIG_ENDIAN)
-
/*
* System IO Config
*/
/*
* FLASH on the Local Bus
*/
-#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
-#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
#define CONFIG_SYS_FLASH_BASE 0xFC000000 /* FLASH base address */
#define CONFIG_SYS_FLASH_SIZE 64 /* FLASH size is 64M */
-#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */
/* Window base at flash base */
#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
/*
* Serial Port
*/
-#define CONFIG_CONS_INDEX 1
#undef CONFIG_SERIAL_SOFTWARE_FIFO
-#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600)
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-
-/* Pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-#define CONFIG_OF_STDOUT_VIA_ALIAS 1
-
/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL
/* enable PCIE clock */
#define CONFIG_SYS_SCCR_PCIEXP1CM 1
-#define CONFIG_PCI
#define CONFIG_PCI_INDIRECT_BRIDGE
#define CONFIG_PCIE
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
-
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
#define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1
/*
* TSEC
*/
-#define CONFIG_TSEC_ENET /* TSEC ethernet support */
#define CONFIG_SYS_TSEC1_OFFSET 0x24000
#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
#define CONFIG_SYS_TSEC2_OFFSET 0x25000
/*
* TSEC ethernet configuration
*/
-#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_TSEC1_NAME "eTSEC0"
#define CONFIG_TSEC2_NAME "eTSEC1"
#define TSEC1_PHY_ADDR 1
/*
* Environment
*/
-#define CONFIG_ENV_IS_IN_FLASH 1
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \
CONFIG_SYS_MONITOR_LEN)
#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
/*
* Command line configuration.
*/
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
/*
* Miscellaneous configurable options
*/
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
/* Boot Argument Buffer Size */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
#define CONFIG_HAS_ETH1
#endif
-#define CONFIG_BAUDRATE 115200
-
#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
-#define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
projects / J-u-boot.git / blobdiff