#define CONFIG_440 1 /* ... PPC440 family */
#define CONFIG_4xx 1 /* ... PPC4xx family */
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE 0xFFF80000
+#endif
+
/*
* Include common defines/options for all AMCC eval boards
*/
/*
* Define this if you want support for video console with radeon 9200 pci card
- * Also set TEXT_BASE to 0xFFF80000 in board/amcc/sequoia/config.mk in this case
+ * Also set CONFIG_SYS_TEXT_BASE to 0xFFF80000 in board/amcc/sequoia/config.mk in this case
*/
#undef CONFIG_VIDEO
#define CONFIG_SYS_PCI_MEMBASE2 CONFIG_SYS_PCI_MEMBASE1 + 0x10000000
#define CONFIG_SYS_PCI_MEMBASE3 CONFIG_SYS_PCI_MEMBASE2 + 0x10000000
-/* Don't change either of these */
-#define CONFIG_SYS_PERIPHERAL_BASE 0xef600000 /* internal peripherals */
-
#define CONFIG_SYS_USB2D0_BASE 0xe0000100
#define CONFIG_SYS_USB_DEVICE 0xe0000000
#define CONFIG_SYS_USB_HOST 0xe0000400
*/
/* 440EPx/440GRx have 16KB of internal SRAM, so no need for D-Cache */
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_BASE /* OCM */
-#define CONFIG_SYS_INIT_RAM_END (4 << 10)
-#define CONFIG_SYS_GBL_DATA_SIZE 256 /* num bytes initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_POST_WORD_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE (4 << 10)
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - 0x4)
/*
* Serial Port
*/
+#define CONFIG_CONS_INDEX 1 /* Use UART0 */
#define CONFIG_SYS_EXT_SERIAL_CLOCK 11059200 /* ext. 11.059MHz clk */
-/* define this if you want console on UART1 */
-#undef CONFIG_UART1_CONSOLE
/*
* Environment
*/
-#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
-#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environ vars */
+#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)
+#define CONFIG_ENV_IS_IN_NAND /* use NAND for environ vars */
+#define CONFIG_ENV_IS_EMBEDDED /* use embedded environment */
+#elif defined(CONFIG_SYS_RAMBOOT)
+#define CONFIG_ENV_IS_NOWHERE /* Store env in memory only */
+#define CONFIG_ENV_SIZE (8 << 10)
+/*
+ * In RAM-booting version, we have no environment storage. So we need to
+ * provide at least preliminary MAC addresses for the 4xx EMAC driver to
+ * register the interfaces. Those two addresses are generated via the
+ * tools/gen_eth_addr tool and should only be used in a closed laboratory
+ * environment.
+ */
+#define CONFIG_ETHADDR 4a:56:49:22:3e:43
+#define CONFIG_ETH1ADDR 02:93:53:d5:06:98
#else
-#define CONFIG_ENV_IS_IN_NAND 1 /* use NAND for environ vars */
-#define CONFIG_ENV_IS_EMBEDDED 1 /* use embedded environment */
+#define CONFIG_ENV_IS_IN_FLASH /* use FLASH for environ vars */
#endif
+#if defined(CONFIG_CMD_FLASH)
/*
* FLASH related
*/
#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
#endif
+#endif /* CONFIG_CMD_FLASH */
/*
* IPL (Initial Program Loader, integrated inside CPU)
#define CONFIG_SYS_NAND_ECCSIZE 256
#define CONFIG_SYS_NAND_ECCBYTES 3
-#define CONFIG_SYS_NAND_ECCSTEPS (CONFIG_SYS_NAND_PAGE_SIZE / CONFIG_SYS_NAND_ECCSIZE)
#define CONFIG_SYS_NAND_OOBSIZE 16
-#define CONFIG_SYS_NAND_ECCTOTAL (CONFIG_SYS_NAND_ECCBYTES * CONFIG_SYS_NAND_ECCSTEPS)
#define CONFIG_SYS_NAND_ECCPOS {0, 1, 2, 3, 6, 7}
#ifdef CONFIG_ENV_IS_IN_NAND
* DDR SDRAM
*/
#define CONFIG_SYS_MBYTES_SDRAM (256) /* 256MB */
-#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
+#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) && \
+ !defined(CONFIG_SYS_RAMBOOT)
#define CONFIG_DDR_DATA_EYE /* use DDR2 optimization */
#endif
#define CONFIG_SYS_MEM_TOP_HIDE (4 << 10) /* don't use last 4kbytes */
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
+/* I2C bootstrap EEPROM */
+#define CONFIG_4xx_CONFIG_I2C_EEPROM_ADDR 0x52
+#define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET 0
+#define CONFIG_4xx_CONFIG_BLOCKSIZE 16
+
/* I2C SYSMON (LM75, AD7414 is almost compatible) */
#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */
#define CONFIG_DTT_AD7414 1 /* use AD7414 */
/* USB */
#ifdef CONFIG_440EPX
+
+#undef CONFIG_USB_EHCI /* OHCI by default */
+
+#ifdef CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_PPC4XX
+#define CONFIG_SYS_PPC4XX_USB_ADDR 0xe0000300
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_EHCI_MMIO_BIG_ENDIAN
+#define CONFIG_EHCI_DESC_BIG_ENDIAN
+#ifdef CONFIG_4xx_DCACHE
+#define CONFIG_EHCI_DCACHE
+#endif
+#else /* CONFIG_USB_EHCI */
#define CONFIG_USB_OHCI_NEW
-#define CONFIG_USB_STORAGE
#define CONFIG_SYS_OHCI_BE_CONTROLLER
#undef CONFIG_SYS_USB_OHCI_BOARD_INIT
#define CONFIG_SYS_USB_OHCI_REGS_BASE CONFIG_SYS_USB_HOST
#define CONFIG_SYS_USB_OHCI_SLOT_NAME "ppc440"
#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
+#endif
+#define CONFIG_USB_STORAGE
/* Comment this out to enable USB 1.1 device */
#define USB_2_0_DEVICE
/*
* Commands additional to the ones defined in amcc-common.h
*/
+#define CONFIG_CMD_CHIP_CONFIG
#define CONFIG_CMD_DTT
#define CONFIG_CMD_FAT
#define CONFIG_CMD_NAND
#define CONFIG_SYS_POST_FPU_ON 0
#endif
+/*
+ * Don't run the memory POST on the NAND-booting version. It will
+ * overwrite part of the U-Boot image which is already loaded from NAND
+ * to SDRAM.
+ */
+#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_SYS_RAMBOOT)
+#define CONFIG_SYS_POST_MEMORY_ON 0
+#else
+#define CONFIG_SYS_POST_MEMORY_ON CONFIG_SYS_POST_MEMORY
+#endif
+
/* POST support */
#define CONFIG_POST (CONFIG_SYS_POST_CACHE | \
CONFIG_SYS_POST_CPU | \
CONFIG_SYS_POST_ETHER | \
- CONFIG_SYS_POST_FPU_ON | \
+ CONFIG_SYS_POST_FPU_ON | \
CONFIG_SYS_POST_I2C | \
- CONFIG_SYS_POST_MEMORY | \
+ CONFIG_SYS_POST_MEMORY_ON | \
CONFIG_SYS_POST_SPR | \
CONFIG_SYS_POST_UART)
-#define CONFIG_SYS_POST_WORD_ADDR (CONFIG_SYS_GBL_DATA_OFFSET - 0x4)
#define CONFIG_LOGBUFFER
#define CONFIG_SYS_POST_CACHE_ADDR 0x7fff0000 /* free virtual address */
/* Board-specific PCI */
#define CONFIG_SYS_PCI_TARGET_INIT
#define CONFIG_SYS_PCI_MASTER_INIT
+#define CONFIG_SYS_PCI_BOARD_FIXUP_IRQ
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
#define CONFIG_SYS_PCI_SUBSYS_ID 0xcafe /* Whatever */
/*
* On Sequoia CS0 and CS3 are switched when configuring for NAND booting
*/
-#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
+#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) && \
+ !defined(CONFIG_SYS_RAMBOOT)
#define CONFIG_SYS_NAND_CS 3 /* NAND chip connected to CSx */
/* Memory Bank 0 (NOR-FLASH) initialization */
#define CONFIG_SYS_EBC_PB0AP 0x03017200
* NAND FLASH
*/
#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define NAND_MAX_CHIPS 1
#define CONFIG_SYS_NAND_BASE (CONFIG_SYS_NAND_ADDR + CONFIG_SYS_NAND_CS)
#define CONFIG_SYS_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */
projects / J-u-boot.git / blobdiff