nanopc-t4: Enable USB Gadget

[J-u-boot.git] / README

diff --git a/README b/README
index 0f9578586f9a09d16e00e638e3c339c288c69dcc..17dc0ee33ba23d18f504de11fb5106f91aa328fa 100644 (file)
--- a/README
+++ b/README
@@ -896,8 +896,6 @@ The following options need to be configured:
 
                CONFIG_TULIP
                Support for Digital 2114x chips.
-               Optional CONFIG_TULIP_SELECT_MEDIA for board specific
-               modem chip initialisation (KS8761/QS6611).
 
                CONFIG_NATSEMI
                Support for National dp83815 chips.
@@ -1632,16 +1630,6 @@ The following options need to be configured:
                  - activate this driver with CONFIG_SYS_I2C_RCAR
                  - This driver adds 4 i2c buses
 
-                 - CONFIG_SYS_RCAR_I2C0_BASE for setting the register channel 0
-                 - CONFIG_SYS_RCAR_I2C0_SPEED for for the speed channel 0
-                 - CONFIG_SYS_RCAR_I2C1_BASE for setting the register channel 1
-                 - CONFIG_SYS_RCAR_I2C1_SPEED for for the speed channel 1
-                 - CONFIG_SYS_RCAR_I2C2_BASE for setting the register channel 2
-                 - CONFIG_SYS_RCAR_I2C2_SPEED for for the speed channel 2
-                 - CONFIG_SYS_RCAR_I2C3_BASE for setting the register channel 3
-                 - CONFIG_SYS_RCAR_I2C3_SPEED for for the speed channel 3
-                 - CONFIF_SYS_RCAR_I2C_NUM_CONTROLLERS for number of i2c buses
-
                - drivers/i2c/sh_i2c.c:
                  - activate this driver with CONFIG_SYS_I2C_SH
                  - This driver adds from 2 to 5 i2c buses
@@ -2485,14 +2473,6 @@ Configuration Settings:
 - CONFIG_SYS_BAUDRATE_TABLE:
                List of legal baudrate settings for this board.
 
-- CONFIG_SYS_MEMTEST_START, CONFIG_SYS_MEMTEST_END:
-               Begin and End addresses of the area used by the
-               simple memory test.
-
-- CONFIG_SYS_MEMTEST_SCRATCH:
-               Scratch address used by the alternate memory test
-               You only need to set this if address zero isn't writeable
-
 - CONFIG_SYS_MEM_RESERVE_SECURE
                Only implemented for ARMv8 for now.
                If defined, the size of CONFIG_SYS_MEM_RESERVE_SECURE memory
@@ -2749,10 +2729,6 @@ Configuration Settings:
        regular expression. This allows multiple variables to define the same
        flags without explicitly listing them for each variable.
 
-- CONFIG_ENV_ACCESS_IGNORE_FORCE
-       If defined, don't allow the -f switch to env set override variable
-       access flags.
-
 The following definitions that deal with the placement and management
 of environment data (variable area); in general, we support the
 following configurations:
@@ -3186,16 +3162,6 @@ necessary. For example using the ELDK on a 4xx CPU, please enter:
        $ CROSS_COMPILE=ppc_4xx-
        $ export CROSS_COMPILE
 
-Note: If you wish to generate Windows versions of the utilities in
-      the tools directory you can use the MinGW toolchain
-      (http://www.mingw.org).  Set your HOST tools to the MinGW
-      toolchain and execute 'make tools'.  For example:
-
-       $ make HOSTCC=i586-mingw32msvc-gcc HOSTSTRIP=i586-mingw32msvc-strip tools
-
-      Binaries such as tools/mkimage.exe will be created which can
-      be executed on computers running Windows.
-
 U-Boot is intended to be simple to build. After installing the
 sources you must configure U-Boot for one specific board type. This
 is done by typing:
@@ -3203,9 +3169,9 @@ is done by typing:
        make NAME_defconfig
 
 where "NAME_defconfig" is the name of one of the existing configu-
-rations; see boards.cfg for supported names.
+rations; see configs/*_defconfig for supported names.
 
-Note: for some board special configuration names may exist; check if
+Note: for some boards special configuration names may exist; check if
       additional information is available from the board vendor; for
       instance, the TQM823L systems are available without (standard)
       or with LCD support. You can select such additional "features"
@@ -4639,7 +4605,7 @@ int main(int argc, char *argv[])
        while (learning) {
                Read the README file in the top level directory;
                Read http://www.denx.de/twiki/bin/view/DULG/Manual;
-               Read applicable doc/*.README;
+               Read applicable doc/README.*;
                Read the source, Luke;
                /* find . -name "*.[chS]" | xargs grep -i <keyword> */
        }