menu "Info commands"
+config CMD_ACPI
+ bool "acpi"
+ default y if ACPIGEN
+ help
+ List and dump ACPI tables. ACPI (Advanced Configuration and Power
+ Interface) is used mostly on x86 for providing information to the
+ Operating System about devices in the system. The tables are set up
+ by the firmware, typically U-Boot but possibly an earlier firmware
+ module, if U-Boot is chain-loaded from something else. ACPI tables
+ can also include code, to perform hardware-specific tasks required
+ by the Operating Systems. This allows some amount of separation
+ between the firmware and OS, and is particularly useful when you
+ want to make hardware changes without the OS needing to be adjusted.
+
config CMD_BDI
bool "bdinfo"
default y
help
Register dump
+config CMD_TLV_EEPROM
+ bool "tlv_eeprom"
+ depends on I2C_EEPROM
+ help
+ Display and program the system EEPROM data block in ONIE Tlvinfo
+ format. TLV stands for Type-Length-Value.
+
+config SPL_CMD_TLV_EEPROM
+ bool "tlv_eeprom for SPL"
+ depends on SPL_I2C_EEPROM
+ select SPL_DRIVERS_MISC_SUPPORT
+ help
+ Read system EEPROM data block in ONIE Tlvinfo format from SPL.
+
endmenu
menu "Boot commands"
files should be merged in one dtb further, which needs to be passed to
the kernel, as part of a boot process.
+config CMD_ABOOTIMG
+ bool "abootimg"
+ depends on ANDROID_BOOT_IMAGE
+ help
+ Android Boot Image manipulation commands. Allows one to extract
+ images contained in boot.img, like kernel, ramdisk, dtb, etc, and
+ obtain corresponding meta-information from boot.img.
+
+ See doc/android/boot-image.rst for details.
+
config CMD_ELF
bool "bootelf, bootvx"
default y
+ select LIB_ELF
help
Boot an ELF/vxWorks image from the memory.
base - print or set address offset
loop - initialize loop on address range
-config MX_CYCLIC
+config CMD_MX_CYCLIC
bool "Enable cyclic md/mw commands"
depends on CMD_MEMORY
help
help
Use a more complete alternative memory test.
-endif
+config SYS_MEMTEST_START
+ hex "default start address for mtest"
+ default 0
+ help
+ This is the default start address for mtest for simple read/write
+ test. If no arguments are given to mtest, default address is used
+ as start address.
-config CMD_MX_CYCLIC
- bool "mdc, mwc"
+config SYS_MEMTEST_END
+ hex "default end address for mtest"
+ default 0x1000
help
- mdc - memory display cyclic
- mwc - memory write cyclic
+ This is the default end address for mtest for simple read/write
+ test. If no arguments are given to mtest, default address is used
+ as end address.
+
+endif
config CMD_SHA1SUM
bool "sha1sum"
Support decompressing an LZMA (Lempel-Ziv-Markov chain algorithm)
image from memory.
+config CMD_UNLZ4
+ bool "unlz4"
+ default y if CMD_BOOTI
+ select LZ4
+ help
+ Support decompressing an LZ4 image from memory region.
+
config CMD_UNZIP
bool "unzip"
default y if CMD_BOOTI
Android devices. Fastboot requires either the network stack
enabled or support for acting as a USB device.
- See doc/android/fastboot.txt for more information.
-
-config CMD_FDC
- bool "fdcboot - Boot from floppy device"
- help
- The 'fdtboot' command allows booting an image from a floppy disk.
+ See doc/android/fastboot.rst for more information.
config CMD_FLASH
bool "flinfo, erase, protect"
help
MMC memory mapped support.
+if CMD_MMC
+
+config CMD_BKOPS_ENABLE
+ bool "mmc bkops enable"
+ depends on CMD_MMC
+ default n
+ help
+ Enable command for setting manual background operations handshake
+ on a eMMC device. The feature is optionally available on eMMC devices
+ conforming to standard >= 4.41.
+
config CMD_MMC_RPMB
bool "Enable support for RPMB in the mmc command"
- depends on CMD_MMC
+ depends on SUPPORT_EMMC_RPMB
help
Enable the commands for reading, writing and programming the
key for the Replay Protection Memory Block partition in eMMC.
config CMD_MMC_SWRITE
bool "mmc swrite"
- depends on CMD_MMC && MMC_WRITE
+ depends on MMC_WRITE
select IMAGE_SPARSE
help
Enable support for the "mmc swrite" command to write Android sparse
images to eMMC.
+endif
+
config CMD_MTD
bool "mtd"
depends on MTD
option provides a way to control this. The commands that are enabled
vary depending on the board.
-config CMD_BKOPS_ENABLE
- bool "mmc bkops enable"
- depends on CMD_MMC
- default n
- help
- Enable command for setting manual background operations handshake
- on a eMMC device. The feature is optionally available on eMMC devices
- conforming to standard >= 4.41.
-
config CMD_BLOCK_CACHE
bool "blkcache - control and stats for block cache"
depends on BLOCK_CACHE
help
The bedbug (emBEDded deBUGger) command provides debugging features
for some PowerPC processors. For details please see the
- docuemntation in doc/README.beddbug
+ documentation in doc/README.bedbug.
config CMD_DIAG
bool "diag - Board diagnostics"
It is also strongly encouraged to also enable CONFIG_MTD to get full
partition support.
+config CMD_UBI_RENAME
+ bool "Enable rename"
+ depends on CMD_UBI
+ default n
+ help
+ Enable a "ubi" command to rename ubi volume:
+ ubi rename <oldname> <newname>
+
config CMD_UBIFS
tristate "Enable UBIFS - Unsorted block images filesystem commands"
depends on CMD_UBI
projects / J-u-boot.git / blobdiff