*
* Configuration for the flea3 board.
*
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#include <asm/arch/imx-regs.h>
/* High Level Configuration Options */
-#define CONFIG_ARM1136 /* This is an arm1136 CPU core */
#define CONFIG_MX35
-#define CONFIG_MX35_HCLK_FREQ 24000000
#define CONFIG_SYS_DCACHE_OFF
+#define CONFIG_SYS_CACHELINE_SIZE 32
#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_SYS_GENERIC_BOARD
/* Only in case the value is not present in mach-types.h */
#ifndef MACH_TYPE_FLEA3
/* Set TEXT at the beginning of the NOR flash */
#define CONFIG_SYS_TEXT_BASE 0xA0000000
-#define CONFIG_SYS_64BIT_VSPRINTF
-
/* This is required to setup the ESDC controller */
#define CONFIG_BOARD_EARLY_INIT_F
/*
* Hardware drivers
*/
-#define CONFIG_HARD_I2C
-#define CONFIG_I2C_MXC
-#define CONFIG_SYS_I2C_MX35_PORT3
-#define CONFIG_SYS_I2C_SPEED 100000
-#define CONFIG_SYS_I2C_SLAVE 0xfe
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
+#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
+#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
+#define CONFIG_SYS_SPD_BUS_NUM 2 /* I2C3 */
+#define CONFIG_SYS_MXC_I2C3_SLAVE 0xfe
#define CONFIG_MXC_SPI
#define CONFIG_MXC_GPIO
#define CONFIG_ENV_OVERWRITE
#define CONFIG_CONS_INDEX 1
#define CONFIG_BAUDRATE 115200
-#define CONFIG_SYS_BAUDRATE_TABLE {9600, 19200, 38400, 57600, 115200}
/*
* Command definition
*/
-
-#include <config_cmd_default.h>
-
#define CONFIG_CMD_PING
#define CONFIG_CMD_DHCP
#define CONFIG_BOOTP_SUBNETMASK
#define CONFIG_BOOTP_DNS
#define CONFIG_CMD_NAND
+#define CONFIG_CMD_CACHE
#define CONFIG_CMD_I2C
#define CONFIG_CMD_SPI
#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
#define CONFIG_NET_RETRY_COUNT 100
#define CONFIG_BOOTDELAY 3
#define CONFIG_FEC_MXC_PHYADDR 0x1
#define CONFIG_MII
-#define CONFIG_DISCOVER_PHY
#define CONFIG_ARP_TIMEOUT 200UL
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_PROMPT "flea3 U-Boot > "
#define CONFIG_CMDLINE_EDITING
#define CONFIG_SYS_HUSH_PARSER /* Use the HUSH parser */
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#define CONFIG_AUTO_COMPLETE
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#define CONFIG_SYS_MEMTEST_START 0 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x10000
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
-#define CONFIG_SYS_HZ 1000
-
-
-/*
- * Stack sizes
- *
- * The stack sizes are set up in start.S using the settings below
- */
-#define CONFIG_STACKSIZE (128 * 1024) /* regular stack */
-
/*
* Physical Memory Map
*/
* NAND FLASH driver setup
*/
#define CONFIG_NAND_MXC
-#define CONFIG_NAND_MXC_V1_1
#define CONFIG_MXC_NAND_REGS_BASE (NFC_BASE_ADDR)
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_BASE (NFC_BASE_ADDR)
* Default environment and default scripts
* to update uboot and load kernel
*/
-#define xstr(s) str(s)
-#define str(s) #s
#define CONFIG_HOSTNAME flea3
#define CONFIG_EXTRA_ENV_SETTINGS \
":${hostname}:${netdev}:off panic=1\0" \
"addip_dyn=setenv bootargs ${bootargs} ip=dhcp\0" \
"addip=if test -n ${ipdyn};then run addip_dyn;" \
- "else run addip_sta;fi\0" \
+ "else run addip_sta;fi\0" \
"addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
"addtty=setenv bootargs ${bootargs}" \
" console=ttymxc2,${baudrate}\0" \
"addmisc=setenv bootargs ${bootargs} ${misc}\0" \
"loadaddr=80800000\0" \
"kernel_addr_r=80800000\0" \
- "hostname=" xstr(CONFIG_HOSTNAME) "\0" \
- "bootfile=" xstr(CONFIG_HOSTNAME) "/uImage\0" \
- "ramdisk_file=" xstr(CONFIG_HOSTNAME) "/uRamdisk\0" \
+ "hostname=" __stringify(CONFIG_HOSTNAME) "\0" \
+ "bootfile=" __stringify(CONFIG_HOSTNAME) "/uImage\0" \
+ "ramdisk_file=" __stringify(CONFIG_HOSTNAME) "/uRamdisk\0" \
"flash_self=run ramargs addip addtty addmtd addmisc;" \
"bootm ${kernel_addr} ${ramdisk_addr}\0" \
"flash_nfs=run nfsargs addip addtty addmtd addmisc;" \
"run ramargs addip addtty addmtd addmisc;" \
"bootm ${kernel_addr_r} ${ramdisk_addr_r};" \
"else echo Images not loades;fi\0" \
- "u-boot=" xstr(CONFIG_HOSTNAME) "/u-boot.bin\0" \
+ "u-boot=" __stringify(CONFIG_HOSTNAME) "/u-boot.bin\0" \
"load=tftp ${loadaddr} ${u-boot}\0" \
- "uboot_addr=" xstr(CONFIG_SYS_MONITOR_BASE) "\0" \
+ "uboot_addr=" __stringify(CONFIG_SYS_MONITOR_BASE) "\0" \
"update=protect off ${uboot_addr} +40000;" \
"erase ${uboot_addr} +40000;" \
"cp.b ${loadaddr} ${uboot_addr} ${filesize}\0" \
projects / J-u-boot.git / blobdiff