*
* Copyright 2000 MontaVista Software Inc.
*/
#include <common.h>
#include <errno.h>
#include <log.h>
#include <pci.h>
+#include <time.h>
+#include "pci_internal.h"
-/* the user can define CONFIG_SYS_PCI_CACHE_LINE_SIZE to avoid problems */
-#ifndef CONFIG_SYS_PCI_CACHE_LINE_SIZE
-#define CONFIG_SYS_PCI_CACHE_LINE_SIZE 8
+/* the user can define CFG_SYS_PCI_CACHE_LINE_SIZE to avoid problems */
+#ifndef CFG_SYS_PCI_CACHE_LINE_SIZE
+#define CFG_SYS_PCI_CACHE_LINE_SIZE 8
#endif
-static void dm_pciauto_setup_device(struct udevice *dev, int bars_num,
+static void dm_pciauto_setup_device(struct udevice *dev,
struct pci_region *mem,
struct pci_region *prefetch,
struct pci_region *io)
pci_size_t bar_size;
u16 cmdstat = 0;
int bar, bar_nr = 0;
+ int bars_num;
u8 header_type;
int rom_addr;
pci_addr_t bar_value;
cmdstat = (cmdstat & ~(PCI_COMMAND_IO | PCI_COMMAND_MEMORY)) |
PCI_COMMAND_MASTER;
+ dm_pci_read_config8(dev, PCI_HEADER_TYPE, &header_type);
+ header_type &= 0x7f;
+
+ switch (header_type) {
+ case PCI_HEADER_TYPE_NORMAL:
+ bars_num = 6;
+ break;
+ case PCI_HEADER_TYPE_BRIDGE:
+ bars_num = 2;
+ break;
+ case PCI_HEADER_TYPE_CARDBUS:
+ /* CardBus header does not have any BAR */
+ bars_num = 0;
+ break;
+ default:
+ /* Skip configuring BARs for unknown header types */
+ bars_num = 0;
+ break;
+ }
+
for (bar = PCI_BASE_ADDRESS_0;
bar < PCI_BASE_ADDRESS_0 + (bars_num * 4); bar += 4) {
int ret = 0;
}
/* Configure the expansion ROM address */
- dm_pci_read_config8(dev, PCI_HEADER_TYPE, &header_type);
- header_type &= 0x7f;
- if (header_type != PCI_HEADER_TYPE_CARDBUS) {
+ if (header_type == PCI_HEADER_TYPE_NORMAL ||
+ header_type == PCI_HEADER_TYPE_BRIDGE) {
rom_addr = (header_type == PCI_HEADER_TYPE_NORMAL) ?
PCI_ROM_ADDRESS : PCI_ROM_ADDRESS1;
dm_pci_write_config32(dev, rom_addr, 0xfffffffe);
dm_pci_write_config16(dev, PCI_COMMAND, cmdstat);
dm_pci_write_config8(dev, PCI_CACHE_LINE_SIZE,
- CONFIG_SYS_PCI_CACHE_LINE_SIZE);
+ CFG_SYS_PCI_CACHE_LINE_SIZE);
dm_pci_write_config8(dev, PCI_LATENCY_TIMER, 0x80);
}
+/*
+ * Check if the link of a downstream PCIe port operates correctly.
+ *
+ * For that check if the optional Data Link Layer Link Active status gets
+ * on within a 200ms period or failing that wait until the completion of
+ * that period and check if link training has shown the completed status
+ * continuously throughout the second half of that period.
+ *
+ * Observation with the ASMedia ASM2824 Gen 3 switch indicates it takes
+ * 11-44ms to indicate the Data Link Layer Link Active status at 2.5GT/s,
+ * though it may take a couple of link training iterations.
+ */
+static bool dm_pciauto_exp_link_stable(struct udevice *dev, int pcie_off)
+{
+ u64 loops = 0, trcount = 0, ntrcount = 0, flips = 0;
+ bool dllla, lnktr, plnktr;
+ u16 exp_lnksta;
+ pci_dev_t bdf;
+ u64 end;
+
+ dm_pci_read_config16(dev, pcie_off + PCI_EXP_LNKSTA, &exp_lnksta);
+ plnktr = !!(exp_lnksta & PCI_EXP_LNKSTA_LT);
+
+ end = get_ticks() + usec_to_tick(200000);
+ do {
+ dm_pci_read_config16(dev, pcie_off + PCI_EXP_LNKSTA,
+ &exp_lnksta);
+ dllla = !!(exp_lnksta & PCI_EXP_LNKSTA_DLLLA);
+ lnktr = !!(exp_lnksta & PCI_EXP_LNKSTA_LT);
+
+ flips += plnktr ^ lnktr;
+ if (lnktr) {
+ ntrcount = 0;
+ trcount++;
+ } else {
+ ntrcount++;
+ }
+ loops++;
+
+ plnktr = lnktr;
+ } while (!dllla && get_ticks() < end);
+
+ bdf = dm_pci_get_bdf(dev);
+ debug("PCI Autoconfig: %02x.%02x.%02x: Fixup link: DL active: %u; "
+ "%3llu flips, %6llu loops of which %6llu while training, "
+ "final %6llu stable\n",
+ PCI_BUS(bdf), PCI_DEV(bdf), PCI_FUNC(bdf),
+ (unsigned int)dllla,
+ (unsigned long long)flips, (unsigned long long)loops,
+ (unsigned long long)trcount, (unsigned long long)ntrcount);
+
+ return dllla || ntrcount >= loops / 2;
+}
+
+/*
+ * Retrain the link of a downstream PCIe port by hand if necessary.
+ *
+ * This is needed at least where a downstream port of the ASMedia ASM2824
+ * Gen 3 switch is wired to the upstream port of the Pericom PI7C9X2G304
+ * Gen 2 switch, and observed with the Delock Riser Card PCI Express x1 >
+ * 2 x PCIe x1 device, P/N 41433, plugged into the SiFive HiFive Unmatched
+ * board.
+ *
+ * In such a configuration the switches are supposed to negotiate the link
+ * speed of preferably 5.0GT/s, falling back to 2.5GT/s. However the link
+ * continues switching between the two speeds indefinitely and the data
+ * link layer never reaches the active state, with link training reported
+ * repeatedly active ~84% of the time. Forcing the target link speed to
+ * 2.5GT/s with the upstream ASM2824 device makes the two switches talk to
+ * each other correctly however. And more interestingly retraining with a
+ * higher target link speed afterwards lets the two successfully negotiate
+ * 5.0GT/s.
+ *
+ * As this can potentially happen with any device and is cheap in the case
+ * of correctly operating hardware, let's do it for all downstream ports,
+ * for root complexes, PCIe switches and PCI/PCI-X to PCIe bridges.
+ *
+ * First check if automatic link training may have failed to complete, as
+ * indicated by the optional Data Link Layer Link Active status being off
+ * and the Link Bandwidth Management Status indicating that hardware has
+ * changed the link speed or width in an attempt to correct unreliable
+ * link operation. If this is the case, then check if the link operates
+ * correctly by seeing whether it is being trained excessively. If it is,
+ * then conclude the link is broken.
+ *
+ * In that case restrict the speed to 2.5GT/s, observing that the Target
+ * Link Speed field is sticky and therefore the link will stay restricted
+ * even after a device reset is later made by an OS that is unaware of the
+ * problem. With the speed restricted request that the link be retrained
+ * and check again if the link operates correctly. If not, then set the
+ * Target Link Speed back to the original value.
+ *
+ * This requires the presence of the Link Control 2 register, so make sure
+ * the PCI Express Capability Version is at least 2. Also don't try, for
+ * obvious reasons, to limit the speed if 2.5GT/s is the only link speed
+ * supported.
+ */
+static void dm_pciauto_exp_fixup_link(struct udevice *dev, int pcie_off)
+{
+ u16 exp_lnksta, exp_lnkctl, exp_lnkctl2;
+ u16 exp_flags, exp_type, exp_version;
+ u32 exp_lnkcap;
+ pci_dev_t bdf;
+
+ dm_pci_read_config16(dev, pcie_off + PCI_EXP_FLAGS, &exp_flags);
+ exp_version = exp_flags & PCI_EXP_FLAGS_VERS;
+ if (exp_version < 2)
+ return;
+
+ exp_type = (exp_flags & PCI_EXP_FLAGS_TYPE) >> 4;
+ switch (exp_type) {
+ case PCI_EXP_TYPE_ROOT_PORT:
+ case PCI_EXP_TYPE_DOWNSTREAM:
+ case PCI_EXP_TYPE_PCIE_BRIDGE:
+ break;
+ default:
+ return;
+ }
+
+ dm_pci_read_config32(dev, pcie_off + PCI_EXP_LNKCAP, &exp_lnkcap);
+ if ((exp_lnkcap & PCI_EXP_LNKCAP_SLS) <= PCI_EXP_LNKCAP_SLS_2_5GB)
+ return;
+
+ dm_pci_read_config16(dev, pcie_off + PCI_EXP_LNKSTA, &exp_lnksta);
+ if ((exp_lnksta & (PCI_EXP_LNKSTA_LBMS | PCI_EXP_LNKSTA_DLLLA)) !=
+ PCI_EXP_LNKSTA_LBMS)
+ return;
+
+ if (dm_pciauto_exp_link_stable(dev, pcie_off))
+ return;
+
+ bdf = dm_pci_get_bdf(dev);
+ printf("PCI Autoconfig: %02x.%02x.%02x: "
+ "Downstream link non-functional\n",
+ PCI_BUS(bdf), PCI_DEV(bdf), PCI_FUNC(bdf));
+ printf("PCI Autoconfig: %02x.%02x.%02x: "
+ "Retrying with speed restricted to 2.5GT/s...\n",
+ PCI_BUS(bdf), PCI_DEV(bdf), PCI_FUNC(bdf));
+
+ dm_pci_read_config16(dev, pcie_off + PCI_EXP_LNKCTL, &exp_lnkctl);
+ dm_pci_read_config16(dev, pcie_off + PCI_EXP_LNKCTL2, &exp_lnkctl2);
+
+ dm_pci_write_config16(dev, pcie_off + PCI_EXP_LNKCTL2,
+ (exp_lnkctl2 & ~PCI_EXP_LNKCTL2_TLS) |
+ PCI_EXP_LNKCTL2_TLS_2_5GT);
+ dm_pci_write_config16(dev, pcie_off + PCI_EXP_LNKCTL,
+ exp_lnkctl | PCI_EXP_LNKCTL_RL);
+
+ if (dm_pciauto_exp_link_stable(dev, pcie_off)) {
+ printf("PCI Autoconfig: %02x.%02x.%02x: Succeeded!\n",
+ PCI_BUS(bdf), PCI_DEV(bdf), PCI_FUNC(bdf));
+ } else {
+ printf("PCI Autoconfig: %02x.%02x.%02x: Failed!\n",
+ PCI_BUS(bdf), PCI_DEV(bdf), PCI_FUNC(bdf));
+
+ dm_pci_write_config16(dev, pcie_off + PCI_EXP_LNKCTL2,
+ exp_lnkctl2);
+ dm_pci_write_config16(dev, pcie_off + PCI_EXP_LNKCTL,
+ exp_lnkctl | PCI_EXP_LNKCTL_RL);
+ }
+}
+
void dm_pciauto_prescan_setup_bridge(struct udevice *dev, int sub_bus)
{
struct pci_region *pci_mem;
u8 io_32;
struct udevice *ctlr = pci_get_controller(dev);
struct pci_controller *ctlr_hose = dev_get_uclass_priv(ctlr);
+ int pcie_off;
pci_mem = ctlr_hose->pci_mem;
pci_prefetch = ctlr_hose->pci_prefetch;
dm_pci_read_config16(dev, PCI_COMMAND, &cmdstat);
dm_pci_read_config16(dev, PCI_PREF_MEMORY_BASE, &prefechable_64);
prefechable_64 &= PCI_PREF_RANGE_TYPE_MASK;
- dm_pci_read_config8(dev, PCI_IO_LIMIT, &io_32);
+ dm_pci_read_config8(dev, PCI_IO_BASE, &io_32);
io_32 &= PCI_IO_RANGE_TYPE_MASK;
/* Configure bus number registers */
cmdstat |= PCI_COMMAND_MEMORY;
} else {
/* We don't support prefetchable memory for now, so disable */
- dm_pci_write_config16(dev, PCI_PREF_MEMORY_BASE, 0x1000 |
+ dm_pci_write_config16(dev, PCI_PREF_MEMORY_BASE, 0xfff0 |
prefechable_64);
dm_pci_write_config16(dev, PCI_PREF_MEMORY_LIMIT, 0x0 |
prefechable_64);
(pci_io->bus_lower & 0xffff0000) >> 16);
cmdstat |= PCI_COMMAND_IO;
+ } else {
+ /* Disable I/O if unsupported */
+ dm_pci_write_config8(dev, PCI_IO_BASE, 0xf0 | io_32);
+ dm_pci_write_config8(dev, PCI_IO_LIMIT, 0x0 | io_32);
+ if (io_32 == PCI_IO_RANGE_TYPE_32) {
+ dm_pci_write_config16(dev, PCI_IO_BASE_UPPER16, 0x0);
+ dm_pci_write_config16(dev, PCI_IO_LIMIT_UPPER16, 0x0);
+ }
}
+ /* For PCIe devices see if we need to retrain the link by hand */
+ pcie_off = dm_pci_find_capability(dev, PCI_CAP_ID_EXP);
+ if (pcie_off)
+ dm_pciauto_exp_fixup_link(dev, pcie_off);
+
/* Enable memory and I/O accesses, enable bus master */
dm_pci_write_config16(dev, PCI_COMMAND, cmdstat | PCI_COMMAND_MASTER);
}
debug("PCI Autoconfig: Found P2P bridge, device %d\n",
PCI_DEV(dm_pci_get_bdf(dev)));
- dm_pciauto_setup_device(dev, 2, pci_mem, pci_prefetch, pci_io);
+ dm_pciauto_setup_device(dev, pci_mem, pci_prefetch, pci_io);
ret = dm_pci_hose_probe_bus(dev);
if (ret < 0)
* just do a minimal setup of the bridge,
* let the OS take care of the rest
*/
- dm_pciauto_setup_device(dev, 0, pci_mem, pci_prefetch, pci_io);
+ dm_pciauto_setup_device(dev, pci_mem, pci_prefetch, pci_io);
debug("PCI Autoconfig: Found P2CardBus bridge, device %d\n",
PCI_DEV(dm_pci_get_bdf(dev)));
break;
#endif
- case PCI_CLASS_PROCESSOR_POWERPC: /* an agent or end-point */
- debug("PCI AutoConfig: Found PowerPC device\n");
- /* fall through */
-
default:
- dm_pciauto_setup_device(dev, 6, pci_mem, pci_prefetch, pci_io);
+ dm_pciauto_setup_device(dev, pci_mem, pci_prefetch, pci_io);
break;
}
projects / J-u-boot.git / blobdiff