board/km: drop CONFIG_KM_ROOTFSSIZE

[J-u-boot.git] / include / configs / MPC8548CDS.h

diff --git a/include/configs/MPC8548CDS.h b/include/configs/MPC8548CDS.h
index e16d870a5e66d5d1175d83712fa433f7770e4a66..eb7a8351794bf0024d97e6df19c4a5a22d8a7f82 100644 (file)
--- a/include/configs/MPC8548CDS.h
+++ b/include/configs/MPC8548CDS.h
@@ -16,10 +16,6 @@
 #define CONFIG_SYS_SRIO
 #define CONFIG_SRIO1                   /* SRIO port 1 */
 
-#define CONFIG_PCI1            /* PCI controller 1 */
-#define CONFIG_PCIE1           /* PCIE controller 1 (slot 1) */
-#undef CONFIG_PCI2
-
 #define CONFIG_INTERRUPTS              /* enable pci, srio, ddr interrupts */
 
 #ifndef __ASSEMBLY__
@@ -30,12 +26,10 @@
  * These can be toggled for performance analysis, otherwise use default.
  */
 #define CONFIG_L2_CACHE                        /* toggle L2 cache */
-#define CONFIG_BTB                     /* toggle branch predition */
 
 /*
  * Only possible on E500 Version 2 or newer cores.
  */
-#define CONFIG_ENABLE_36BIT_PHYS       1
 
 #define CONFIG_SYS_CCSRBAR             0xe0000000
 #define CONFIG_SYS_CCSRBAR_PHYS_LOW    CONFIG_SYS_CCSRBAR
@@ -48,9 +42,6 @@
 #define CONFIG_SYS_DDR_SDRAM_BASE      0x00000000      /* DDR is system memory*/
 #define CONFIG_SYS_SDRAM_BASE          CONFIG_SYS_DDR_SDRAM_BASE
 
-#define CONFIG_DIMM_SLOTS_PER_CTLR     1
-#define CONFIG_CHIP_SELECTS_PER_CTRL   (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
-
 /* I2C addresses of SPD EEPROMs */
 #define SPD_EEPROM_ADDRESS     0x51    /* CTLR 0 DIMM 0 */
 
@@ -133,14 +124,6 @@
 
 #define CONFIG_SYS_FLASH_BANKS_LIST \
        {CONFIG_SYS_FLASH_BASE_PHYS + 0x800000, CONFIG_SYS_FLASH_BASE_PHYS}
-#define CONFIG_SYS_MAX_FLASH_SECT      128             /* sectors per device */
-#undef CONFIG_SYS_FLASH_CHECKSUM
-#define CONFIG_SYS_FLASH_ERASE_TOUT    60000   /* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT    500     /* Flash Write Timeout (ms) */
-
-#define CONFIG_SYS_MONITOR_BASE        CONFIG_SYS_TEXT_BASE    /* start of monitor */
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO
 
 #define CONFIG_HWCONFIG                        /* enable hwconfig */
 
@@ -250,8 +233,7 @@
 #define CONFIG_SYS_INIT_RAM_ADDR       0xe4010000      /* Initial RAM address */
 #define CONFIG_SYS_INIT_RAM_SIZE       0x4000          /* Size of used area in RAM */
 
-#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET      CONFIG_SYS_GBL_DATA_OFFSET
+#define CONFIG_SYS_INIT_SP_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 
 #define CONFIG_SYS_MONITOR_LEN         (512 * 1024)
 
@@ -271,13 +253,8 @@
  */
 #if !CONFIG_IS_ENABLED(DM_I2C)
 #define CONFIG_SYS_I2C_NOPROBES                { {0, 0x69} }
-#else
-#define CONFIG_SYS_SPD_BUS_NUM 0
 #endif
 
-/* EEPROM */
-#define CONFIG_SYS_I2C_EEPROM_CCID
-
 /*
  * General PCI
  * Memory space is mapped 1-1, but I/O space must start from 0.
@@ -326,18 +303,6 @@
 #endif
 #define CONFIG_SYS_SRIO1_MEM_SIZE      0x20000000      /* 512M */
 
-#ifdef CONFIG_LEGACY
-#define BRIDGE_ID 17
-#define VIA_ID 2
-#else
-#define BRIDGE_ID 28
-#define VIA_ID 4
-#endif
-
-#if defined(CONFIG_PCI)
-#define CONFIG_PCI_SCAN_SHOW           /* show pci devices on startup */
-#endif /* CONFIG_PCI */
-
 #if defined(CONFIG_TSEC_ENET)
 
 #define CONFIG_TSEC1   1
@@ -363,9 +328,6 @@
 #define TSEC2_FLAGS            TSEC_GIGABIT
 #define TSEC3_FLAGS            (TSEC_GIGABIT | TSEC_REDUCED)
 #define TSEC4_FLAGS            (TSEC_GIGABIT | TSEC_REDUCED)
-
-/* Options are: eTSEC[0-3] */
-#define CONFIG_ETHPRIME                "eTSEC0"
 #endif /* CONFIG_TSEC_ENET */
 
 /*
@@ -375,11 +337,6 @@
 #define CONFIG_LOADS_ECHO      1       /* echo on for serial download */
 #define CONFIG_SYS_LOADS_BAUD_CHANGE   1       /* allow baudrate change */
 
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-
 /*
  * Miscellaneous configurable options
  */
@@ -390,23 +347,15 @@
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CONFIG_SYS_BOOTMAPSZ   (64 << 20)      /* Initial Memory map for Linux*/
-#define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */
 
 /*
  * Environment Configuration
  */
-#if defined(CONFIG_TSEC_ENET)
-#define CONFIG_HAS_ETH0
-#define CONFIG_HAS_ETH1
-#define CONFIG_HAS_ETH2
-#define CONFIG_HAS_ETH3
-#endif
 
 #define CONFIG_IPADDR   192.168.1.253
 
 #define CONFIG_HOSTNAME         "unknown"
 #define CONFIG_ROOTPATH         "/nfsroot"
-#define CONFIG_BOOTFILE "8548cds/uImage.uboot"
 #define CONFIG_UBOOTPATH       8548cds/u-boot.bin      /* TFTP server */
 
 #define CONFIG_SERVERIP         192.168.1.1