#ifndef __CONFIG_H
#define __CONFIG_H
-#include <asm/sizes.h>
/*
* High Level Configuration Options
*/
-#define CONFIG_ARMCORTEXA8 1 /* This is an ARM V7 CPU core */
+#define CONFIG_ARMV7 1 /* This is an ARM V7 CPU core */
#define CONFIG_OMAP 1 /* in a TI OMAP core */
#define CONFIG_OMAP34XX 1 /* which is a 34XX */
#define CONFIG_OMAP3430 1 /* which is in a 3430 */
#define CONFIG_OMAP3_BEAGLE 1 /* working with BEAGLE */
+#define CONFIG_SDRC /* The chip has SDRC controller */
+
#include <asm/arch/cpu.h> /* get chip and board defs */
#include <asm/arch/omap3.h>
+/*
+ * Display CPU and Board information
+ */
+#define CONFIG_DISPLAY_CPUINFO 1
+#define CONFIG_DISPLAY_BOARDINFO 1
+
/* Clock Defines */
#define V_OSCK 26000000 /* Clock output from T2 */
#define V_SCLK (V_OSCK >> 1)
/*
* Size of malloc() pool
*/
-#define CONFIG_ENV_SIZE SZ_128K /* Total Size Environment */
+#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
/* Sector */
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + SZ_128K)
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10))
#define CONFIG_SYS_GBL_DATA_SIZE 128 /* bytes reserved for */
/* initial data */
#define CONFIG_BAUDRATE 115200
#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\
115200}
+#define CONFIG_GENERIC_MMC 1
#define CONFIG_MMC 1
-#define CONFIG_OMAP3_MMC 1
+#define CONFIG_OMAP_HSMMC 1
#define CONFIG_DOS_PARTITION 1
+/* DDR - I use Micron DDR */
+#define CONFIG_OMAP3_MICRON_DDR 1
+
+/* USB */
+#define CONFIG_MUSB_UDC 1
+#define CONFIG_USB_OMAP3 1
+#define CONFIG_TWL4030_USB 1
+
+/* USB device configuration */
+#define CONFIG_USB_DEVICE 1
+#define CONFIG_USB_TTY 1
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1
+
/* commands to include */
#include <config_cmd_default.h>
+#define CONFIG_CMD_CACHE
#define CONFIG_CMD_EXT2 /* EXT2 Support */
#define CONFIG_CMD_FAT /* FAT support */
#define CONFIG_CMD_JFFS2 /* JFFS2 Support */
#define CONFIG_CMD_MTDPARTS /* Enable MTD parts commands */
+#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
#define MTDIDS_DEFAULT "nand0=nand"
#define MTDPARTS_DEFAULT "mtdparts=nand:512k(x-loader),"\
"1920k(u-boot),128k(u-boot-env),"\
#undef CONFIG_CMD_NFS /* NFS support */
#define CONFIG_SYS_NO_FLASH
+#define CONFIG_HARD_I2C 1
#define CONFIG_SYS_I2C_SPEED 100000
#define CONFIG_SYS_I2C_SLAVE 1
#define CONFIG_SYS_I2C_BUS 0
#define CONFIG_SYS_I2C_BUS_SELECT 1
#define CONFIG_DRIVER_OMAP34XX_I2C 1
+/*
+ * TWL4030
+ */
+#define CONFIG_TWL4030_POWER 1
+#define CONFIG_TWL4030_LED 1
+
/*
* Board NAND Info.
*/
+#define CONFIG_SYS_NAND_QUIET_TEST 1
#define CONFIG_NAND_OMAP_GPMC
#define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */
/* to access nand */
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
/* devices */
-#define SECTORSIZE 512
-
-#define NAND_ALLOW_ERASE_ALL
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN 0x00
-#define NAND_MAX_FLOORS 1
-#define NAND_MAX_CHIPS 1
-#define NAND_NO_RB 1
-#define CONFIG_SYS_NAND_WP
-
#define CONFIG_JFFS2_NAND
/* nand device jffs2 lives on */
#define CONFIG_JFFS2_DEV "nand0"
#define CONFIG_EXTRA_ENV_SETTINGS \
"loadaddr=0x82000000\0" \
+ "usbtty=cdc_acm\0" \
"console=ttyS2,115200n8\0" \
- "videomode=1024x768@60,vxres=1024,vyres=768\0" \
- "videospec=omapfb:vram:2M,vram:4M\0" \
+ "mpurate=500\0" \
+ "vram=12M\0" \
+ "dvimode=1024x768MR-16@60\0" \
+ "defaultdisplay=dvi\0" \
+ "mmcdev=0\0" \
+ "mmcroot=/dev/mmcblk0p2 rw\0" \
+ "mmcrootfstype=ext3 rootwait\0" \
+ "nandroot=/dev/mtdblock4 rw\0" \
+ "nandrootfstype=jffs2\0" \
"mmcargs=setenv bootargs console=${console} " \
- "video=${videospec},mode:${videomode} " \
- "root=/dev/mmcblk0p2 rw " \
- "rootfstype=ext3 rootwait\0" \
+ "mpurate=${mpurate} " \
+ "vram=${vram} " \
+ "omapfb.mode=dvi:${dvimode} " \
+ "omapfb.debug=y " \
+ "omapdss.def_disp=${defaultdisplay} " \
+ "root=${mmcroot} " \
+ "rootfstype=${mmcrootfstype}\0" \
"nandargs=setenv bootargs console=${console} " \
- "video=${videospec},mode:${videomode} " \
- "root=/dev/mtdblock4 rw " \
- "rootfstype=jffs2\0" \
- "loadbootscript=fatload mmc 0 ${loadaddr} boot.scr\0" \
+ "mpurate=${mpurate} " \
+ "vram=${vram} " \
+ "omapfb.mode=dvi:${dvimode} " \
+ "omapfb.debug=y " \
+ "omapdss.def_disp=${defaultdisplay} " \
+ "root=${nandroot} " \
+ "rootfstype=${nandrootfstype}\0" \
+ "loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \
"bootscript=echo Running bootscript from mmc ...; " \
- "autoscr ${loadaddr}\0" \
- "loaduimage=fatload mmc 0 ${loadaddr} uImage\0" \
+ "source ${loadaddr}\0" \
+ "loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \
"mmcboot=echo Booting from mmc ...; " \
"run mmcargs; " \
"bootm ${loadaddr}\0" \
"bootm ${loadaddr}\0" \
#define CONFIG_BOOTCOMMAND \
- "if mmcinit; then " \
+ "if mmc rescan ${mmcdev}; then " \
"if run loadbootscript; then " \
"run bootscript; " \
"else " \
/*
* Miscellaneous configurable options
*/
-#define V_PROMPT "OMAP3 beagleboard.org # "
-
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-#define CONFIG_SYS_PROMPT V_PROMPT
+#define CONFIG_SYS_PROMPT "OMAP3 beagleboard.org # "
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
/* Print Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
/* load address */
/*
- * 2430 has 12 GP timers, they can be driven by the SysClk (12/13/19.2) or by
- * 32KHz clk, or from external sig. This rate is divided by a local divisor.
+ * OMAP3 has 12 GP timers, they can be driven by the system clock
+ * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
+ * This rate is divided by a local divisor.
*/
#define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2)
-#define CONFIG_SYS_PTV 7 /* 2^(PTV+1) */
-#define CONFIG_SYS_HZ ((V_SCLK) / (2 << CONFIG_SYS_PTV))
+#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
+#define CONFIG_SYS_HZ 1000
/*-----------------------------------------------------------------------
* Stack sizes
*
* The stack sizes are set up in start.S using the settings below
*/
-#define CONFIG_STACKSIZE SZ_128K /* regular stack */
+#define CONFIG_STACKSIZE (128 << 10) /* regular stack 128 KiB */
#ifdef CONFIG_USE_IRQ
-#define CONFIG_STACKSIZE_IRQ SZ_4K /* IRQ stack */
-#define CONFIG_STACKSIZE_FIQ SZ_4K /* FIQ stack */
+#define CONFIG_STACKSIZE_IRQ (4 << 10) /* IRQ stack 4 KiB */
+#define CONFIG_STACKSIZE_FIQ (4 << 10) /* FIQ stack 4 KiB */
#endif
/*-----------------------------------------------------------------------
*/
#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
-#define PHYS_SDRAM_1_SIZE SZ_32M /* at least 32 meg */
+#define PHYS_SDRAM_1_SIZE (32 << 20) /* at least 32 MiB */
#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
/* SDRAM Bank Allocation method */
#define CONFIG_SYS_MAX_FLASH_SECT 520 /* max number of sectors on */
/* one chip */
#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of flash banks */
-#define CONFIG_SYS_MONITOR_LEN SZ_256K /* Reserve 2 sectors */
+#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
#define CONFIG_SYS_FLASH_BASE boot_flash_base
#define CONFIG_SYS_JFFS2_NUM_BANKS 1
#ifndef __ASSEMBLY__
-extern gpmc_csx_t *nand_cs_base;
-extern gpmc_t *gpmc_cfg_base;
extern unsigned int boot_flash_base;
extern volatile unsigned int boot_flash_env_addr;
extern unsigned int boot_flash_off;
extern unsigned int boot_flash_type;
#endif
-
-#define WRITE_NAND_COMMAND(d, adr)\
- writel(d, &nand_cs_base->nand_cmd)
-#define WRITE_NAND_ADDRESS(d, adr)\
- writel(d, &nand_cs_base->nand_adr)
-#define WRITE_NAND(d, adr) writew(d, &nand_cs_base->nand_dat)
-#define READ_NAND(adr) readl(&nand_cs_base->nand_dat)
-
-/* Other NAND Access APIs */
-#define NAND_WP_OFF() do {readl(&gpmc_cfg_base->config) |= GPMC_CONFIG_WP; } \
- while (0)
-#define NAND_WP_ON() do {readl(&gpmc_cfg_base->config) &= ~GPMC_CONFIG_WP; } \
- while (0)
-#define NAND_DISABLE_CE(nand)
-#define NAND_ENABLE_CE(nand)
-#define NAND_WAIT_READY(nand) udelay(10)
+/* additions for new relocation code, must be added to all boards */
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_SP_ADDR (LOW_LEVEL_SRAM_STACK - CONFIG_SYS_GBL_DATA_SIZE)
#endif /* __CONFIG_H */
projects / J-u-boot.git / blobdiff