*/
#define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */
+#define CONFIG_MPC5200 1 /* (more precisely a MPC5200 CPU) */
#define CONFIG_TOTAL5200 1 /* ... on Total5200 board */
-#define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
+/*
+ * Valid values for CONFIG_SYS_TEXT_BASE are:
+ * 0xFFF00000 boot high (standard configuration)
+ * 0xFE000000 boot low
+ * 0x00100000 boot from RAM (for testing only)
+ */
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE 0xFFF00000
+#endif
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
+#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
+
+#define CONFIG_HIGH_BATS 1 /* High BATs supported */
/*
* Serial console configuration
*/
#define CONFIG_PSC_CONSOLE 3 /* console is on PSC3 */
#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
/*
* Video console
#define CONFIG_SPLASH_SCREEN
-#ifdef CONFIG_MPC5200 /* MGT5100 PCI is not supported yet. */
/*
* PCI Mapping:
* 0x40000000 - 0x4fffffff - PCI Memory
#define CONFIG_PCI 1
#define CONFIG_PCI_PNP 1
#define CONFIG_PCI_SCAN_SHOW 1
+#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1
#define CONFIG_PCI_MEM_BUS 0x40000000
#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS
#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS
#define CONFIG_PCI_IO_SIZE 0x01000000
-#define CONFIG_NET_MULTI 1
#define CONFIG_MII 1
#define CONFIG_EEPRO100 1
-#define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
+#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
#define CONFIG_NS8382X 1
-#else /* MGT5100 */
-
-#define CONFIG_MII 1
-
-#endif
-
/* Partitions */
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
#define CONFIG_USB_STORAGE
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
-#if definded(CONFIG_MPC5200)
- #define CONFIG_CMD_PCI
-#endif
+#define CONFIG_CMD_PCI
#define CONFIG_CMD_BMP
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_USB
-#if (TEXT_BASE == 0xFE000000) /* Boot low */
-# define CFG_LOWBOOT 1
+#if (CONFIG_SYS_TEXT_BASE == 0xFE000000) /* Boot low */
+# define CONFIG_SYS_LOWBOOT 1
#endif
/*
#define CONFIG_PREBOOT \
"setenv stdout serial;setenv stderr serial;" \
"echo;" \
- "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+ "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
"echo"
#undef CONFIG_BOOTARGS
#define CONFIG_BOOTCOMMAND "run flash_self"
-#if defined(CONFIG_MPC5200)
/*
* IPB Bus clocking configuration.
*/
-#undef CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
-#endif
+#undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
/*
* I2C configuration
*/
#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CFG_I2C_MODULE 1 /* Select I2C module #1 or #2 */
+#define CONFIG_SYS_I2C_MODULE 1 /* Select I2C module #1 or #2 */
-#define CFG_I2C_SPEED 100000 /* 100 kHz */
-#define CFG_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
/*
* EEPROM configuration
*/
-#define CFG_I2C_EEPROM_ADDR 0x50 /* 1010000x */
-#define CFG_I2C_EEPROM_ADDR_LEN 1
-#define CFG_EEPROM_PAGE_WRITE_BITS 3
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 70
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70
/*
* Flash configuration
*/
-#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */
-#define CFG_FLASH_CFI_DRIVER 1 /* Use the common driver */
+#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
+#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */
#if CONFIG_TOTAL5200_REV==2
-# define CFG_MAX_FLASH_BANKS 3 /* max num of flash banks */
-# define CFG_FLASH_BANKS_LIST { CFG_CS5_START, CFG_CS4_START, CFG_BOOTCS_START }
+# define CONFIG_SYS_MAX_FLASH_BANKS 3 /* max num of flash banks */
+# define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_CS5_START, CONFIG_SYS_CS4_START, CONFIG_SYS_BOOTCS_START }
#else
-# define CFG_MAX_FLASH_BANKS 1 /* max num of flash banks */
-# define CFG_FLASH_BANKS_LIST { CFG_BOOTCS_START }
+# define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */
+# define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_BOOTCS_START }
#endif
-#define CFG_FLASH_EMPTY_INFO
-#define CFG_MAX_FLASH_SECT 128 /* max num of sects on one chip */
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max num of sects on one chip */
#if CONFIG_TOTAL5200_REV==1
-# define CFG_FLASH_BASE 0xFE000000
-# define CFG_FLASH_SIZE 0x02000000
+# define CONFIG_SYS_FLASH_BASE 0xFE000000
+# define CONFIG_SYS_FLASH_SIZE 0x02000000
#elif CONFIG_TOTAL5200_REV==2
-# define CFG_FLASH_BASE 0xFA000000
-# define CFG_FLASH_SIZE 0x06000000
+# define CONFIG_SYS_FLASH_BASE 0xFA000000
+# define CONFIG_SYS_FLASH_SIZE 0x06000000
#endif /* CONFIG_TOTAL5200_REV */
-#if defined(CFG_LOWBOOT)
-# define CFG_ENV_ADDR 0xFE040000
-#else /* CFG_LOWBOOT */
-# define CFG_ENV_ADDR 0xFFF40000
-#endif /* CFG_LOWBOOT */
+#if defined(CONFIG_SYS_LOWBOOT)
+# define CONFIG_ENV_ADDR 0xFE040000
+#else /* CONFIG_SYS_LOWBOOT */
+# define CONFIG_ENV_ADDR 0xFFF40000
+#endif /* CONFIG_SYS_LOWBOOT */
/*
* Environment settings
*/
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_SIZE 0x40000
-#define CFG_ENV_SECT_SIZE 0x40000
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_SIZE 0x40000
+#define CONFIG_ENV_SECT_SIZE 0x40000
#define CONFIG_ENV_OVERWRITE 1
/*
* Memory map
*/
-#define CFG_SDRAM_BASE 0x00000000
-#define CFG_DEFAULT_MBAR 0x80000000
-#define CFG_MBAR 0xF0000000 /* 64 kB */
-#define CFG_FPGA_BASE 0xF0010000 /* 64 kB */
-#define CFG_CPLD_BASE 0xF0020000 /* 64 kB */
-#define CFG_LCD_BASE 0xF1000000 /* 4096 kB */
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_DEFAULT_MBAR 0x80000000
+#define CONFIG_SYS_MBAR 0xF0000000 /* 64 kB */
+#define CONFIG_SYS_FPGA_BASE 0xF0010000 /* 64 kB */
+#define CONFIG_SYS_CPLD_BASE 0xF0020000 /* 64 kB */
+#define CONFIG_SYS_LCD_BASE 0xF1000000 /* 4096 kB */
/* Use SRAM until RAM will be available */
-#define CFG_INIT_RAM_ADDR MPC5XXX_SRAM
-#define CFG_INIT_RAM_END MPC5XXX_SRAM_SIZE /* End of used area in DPRAM */
+#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
+#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE /* Size of used area in DPRAM */
-#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-#define CFG_MONITOR_BASE TEXT_BASE
-#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
-# define CFG_RAMBOOT 1
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+# define CONFIG_SYS_RAMBOOT 1
#endif
-#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
-#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
+#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*
* Ethernet configuration
*/
#define CONFIG_MPC5xxx_FEC 1
+#define CONFIG_MPC5xxx_FEC_SEVENWIRE
/* dummy, 7-wire FEC does not have phy address */
#define CONFIG_PHY_ADDR 0x00
* PSC1: reset default, changed in AC'97 driver 000
*
*/
-#define CFG_GPS_PORT_CONFIG 0x00000C10
+#define CONFIG_SYS_GPS_PORT_CONFIG 0x00000C10
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_MEMTEST_START 0x00100000 /* memtest works on */
-#define CFG_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
+#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
+#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
-#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
+#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
#if defined(CONFIG_CMD_KGDB)
-# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
/*
* Various low-level settings
*/
-#if defined(CONFIG_MPC5200)
-#define CFG_HID0_INIT HID0_ICE | HID0_ICFI
-#define CFG_HID0_FINAL HID0_ICE
-#else
-#define CFG_HID0_INIT 0
-#define CFG_HID0_FINAL 0
-#endif
-
-#if defined (CONFIG_MGT5100)
-# define CONFIG_BOARD_EARLY_INIT_R /* switch from CS_BOOT to CS0 */
-#endif
+#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI
+#define CONFIG_SYS_HID0_FINAL HID0_ICE
#if CONFIG_TOTAL5200_REV==1
-# define CFG_BOOTCS_START CFG_FLASH_BASE
-# define CFG_BOOTCS_SIZE 0x02000000 /* 32 MB */
-# define CFG_BOOTCS_CFG 0x0004DF00 /* 4WS, MX, AL, CE, AS_25, DS_32 */
-# define CFG_CS0_START CFG_FLASH_BASE
-# define CFG_CS0_SIZE 0x02000000 /* 32 MB */
+# define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
+# define CONFIG_SYS_BOOTCS_SIZE 0x02000000 /* 32 MB */
+# define CONFIG_SYS_BOOTCS_CFG 0x0004DF00 /* 4WS, MX, AL, CE, AS_25, DS_32 */
+# define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE
+# define CONFIG_SYS_CS0_SIZE 0x02000000 /* 32 MB */
#else
-# define CFG_BOOTCS_START (CFG_CS4_START + CFG_CS4_SIZE)
-# define CFG_BOOTCS_SIZE 0x02000000 /* 32 MB */
-# define CFG_BOOTCS_CFG 0x0004DF00 /* 4WS, MX, AL, CE, AS_25, DS_32 */
-# define CFG_CS4_START (CFG_CS5_START + CFG_CS5_SIZE)
-# define CFG_CS4_SIZE 0x02000000 /* 32 MB */
-# define CFG_CS4_CFG 0x0004DF00 /* 4WS, MX, AL, CE, AS_25, DS_32 */
-# define CFG_CS5_START CFG_FLASH_BASE
-# define CFG_CS5_SIZE 0x02000000 /* 32 MB */
-# define CFG_CS5_CFG 0x0004DF00 /* 4WS, MX, AL, CE, AS_25, DS_32 */
+# define CONFIG_SYS_BOOTCS_START (CONFIG_SYS_CS4_START + CONFIG_SYS_CS4_SIZE)
+# define CONFIG_SYS_BOOTCS_SIZE 0x02000000 /* 32 MB */
+# define CONFIG_SYS_BOOTCS_CFG 0x0004DF00 /* 4WS, MX, AL, CE, AS_25, DS_32 */
+# define CONFIG_SYS_CS4_START (CONFIG_SYS_CS5_START + CONFIG_SYS_CS5_SIZE)
+# define CONFIG_SYS_CS4_SIZE 0x02000000 /* 32 MB */
+# define CONFIG_SYS_CS4_CFG 0x0004DF00 /* 4WS, MX, AL, CE, AS_25, DS_32 */
+# define CONFIG_SYS_CS5_START CONFIG_SYS_FLASH_BASE
+# define CONFIG_SYS_CS5_SIZE 0x02000000 /* 32 MB */
+# define CONFIG_SYS_CS5_CFG 0x0004DF00 /* 4WS, MX, AL, CE, AS_25, DS_32 */
#endif
-#define CFG_CS1_START CFG_FPGA_BASE
-#define CFG_CS1_SIZE 0x00010000 /* 64 kB */
-#define CFG_CS1_CFG 0x0019FF00 /* 25WS, MX, AL, AA, CE, AS_25, DS_32 */
+#define CONFIG_SYS_CS1_START CONFIG_SYS_FPGA_BASE
+#define CONFIG_SYS_CS1_SIZE 0x00010000 /* 64 kB */
+#define CONFIG_SYS_CS1_CFG 0x0019FF00 /* 25WS, MX, AL, AA, CE, AS_25, DS_32 */
-#define CFG_CS2_START CFG_LCD_BASE
-#define CFG_CS2_SIZE 0x00400000 /* 4096 kB */
-#define CFG_CS2_CFG 0x0032FD0C /* 50WS, MX, AL, AA, CE, AS_25, DS_16, endian swapping */
+#define CONFIG_SYS_CS2_START CONFIG_SYS_LCD_BASE
+#define CONFIG_SYS_CS2_SIZE 0x00400000 /* 4096 kB */
+#define CONFIG_SYS_CS2_CFG 0x0032FD0C /* 50WS, MX, AL, AA, CE, AS_25, DS_16, endian swapping */
#if CONFIG_TOTAL5200_REV==1
-# define CFG_CS3_START CFG_CPLD_BASE
-# define CFG_CS3_SIZE 0x00010000 /* 64 kB */
-# define CFG_CS3_CFG 0x000ADF00 /* 10WS, MX, AL, CE, AS_25, DS_32 */
+# define CONFIG_SYS_CS3_START CONFIG_SYS_CPLD_BASE
+# define CONFIG_SYS_CS3_SIZE 0x00010000 /* 64 kB */
+# define CONFIG_SYS_CS3_CFG 0x000ADF00 /* 10WS, MX, AL, CE, AS_25, DS_32 */
#else
-# define CFG_CS3_START CFG_CPLD_BASE
-# define CFG_CS3_SIZE 0x00010000 /* 64 kB */
-# define CFG_CS3_CFG 0x000AD800 /* 10WS, MX, AL, CE, AS_24, DS_8 */
+# define CONFIG_SYS_CS3_START CONFIG_SYS_CPLD_BASE
+# define CONFIG_SYS_CS3_SIZE 0x00010000 /* 64 kB */
+# define CONFIG_SYS_CS3_CFG 0x000AD800 /* 10WS, MX, AL, CE, AS_24, DS_8 */
#endif
-#define CFG_CS_BURST 0x00000000
-#define CFG_CS_DEADCYCLE 0x33333333
+#define CONFIG_SYS_CS_BURST 0x00000000
+#define CONFIG_SYS_CS_DEADCYCLE 0x33333333
/*-----------------------------------------------------------------------
* USB stuff
#define CONFIG_IDE_RESET /* reset for ide supported */
#define CONFIG_IDE_PREINIT
-#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */
-#define CFG_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
+#define CONFIG_SYS_ATA_CS_ON_I2C2
+#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
+#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
-#define CFG_ATA_IDE0_OFFSET 0x0000
+#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-#define CFG_ATA_BASE_ADDR MPC5XXX_ATA
+#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA
/* Offset for data I/O */
-#define CFG_ATA_DATA_OFFSET (0x0060)
+#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060)
/* Offset for normal register accesses */
-#define CFG_ATA_REG_OFFSET (CFG_ATA_DATA_OFFSET)
+#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET)
/* Offset for alternate registers */
-#define CFG_ATA_ALT_OFFSET (0x005C)
+#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C)
/* Interval between registers */
-#define CFG_ATA_STRIDE 4
+#define CONFIG_SYS_ATA_STRIDE 4
#endif /* __CONFIG_H */
projects / J-u-boot.git / blobdiff