nand: Merge BCH code from Linux nand driver

[J-u-boot.git] / README

diff --git a/README b/README
index fda0190d5ff99361558591d4b0ba29f56a683bda..9d713e8f4398b9af70844ab7910c67e400817bf6 100644 (file)
--- a/README
+++ b/README
@@ -564,7 +564,7 @@ The following options need to be configured:
 
                CONFIG_CFB_CONSOLE
                Enables console device for a color framebuffer. Needs following
-               defines (cf. smiLynxEM, i8042, board/eltec/bab7xx)
+               defines (cf. smiLynxEM, i8042)
                        VIDEO_FB_LITTLE_ENDIAN  graphic memory organisation
                                                (default big endian)
                        VIDEO_HW_RECTFILL       graphic chip supports
@@ -638,6 +638,32 @@ The following options need to be configured:
                'Sane' compilers will generate smaller code if
                CONFIG_PRE_CON_BUF_SZ is a power of 2
 
+- Pre-console putc():
+               Prior to the console being initialised, console output is
+               normally silently discarded. This can be annoying if a
+               panic() happens in this time.
+
+               If the CONFIG_PRE_CONSOLE_PUTC option is defined, then
+               U-Boot will call board_pre_console_putc() for each output
+               character in this case, This function should try to output
+               the character if possible, perhaps on all available UARTs
+               (it will need to do this directly, since the console code
+               is not functional yet). Note that if the panic happens
+               early enough, then it is possible that board_init_f()
+               (or even arch_cpu_init() on ARM) has not been called yet.
+               You should init all clocks, GPIOs, etc. that are needed
+               to get the character out. Baud rates will need to default
+               to something sensible.
+
+- Safe printf() functions
+               Define CONFIG_SYS_VSNPRINTF to compile in safe versions of
+               the printf() functions. These are defined in
+               include/vsprintf.h and include snprintf(), vsnprintf() and
+               so on. Code size increase is approximately 300-500 bytes.
+               If this option is not given then these functions will
+               silently discard their buffer size argument - this means
+               you are not getting any overflow checking in this case.
+
 - Boot Delay:  CONFIG_BOOTDELAY - in seconds
                Delay before automatically booting the default image;
                set to -1 to disable autoboot.
@@ -1003,6 +1029,9 @@ The following options need to be configured:
                        If this defined, the driver is quiet.
                        The driver doen't show link status messages.
 
+               CONFIG_CALXEDA_XGMAC
+               Support for the Calxeda XGMAC device
+
                CONFIG_DRIVER_LAN91C96
                Support for SMSC's LAN91C96 chips.
 
@@ -1072,6 +1101,16 @@ The following options need to be configured:
                        CONFIG_SH_ETHER_CACHE_WRITEBACK
                        If this option is set, the driver enables cache flush.
 
+- TPM Support:
+               CONFIG_GENERIC_LPC_TPM
+               Support for generic parallel port TPM devices. Only one device
+               per system is supported at this time.
+
+                       CONFIG_TPM_TIS_BASE_ADDRESS
+                       Base address where the generic TPM device is mapped
+                       to. Contemporary x86 systems usually map it at
+                       0xfed40000.
+
 - USB Support:
                At the moment only the UHCI host controller is
                supported (PIP405, MIP405, MPC5200); define
@@ -1158,6 +1197,14 @@ The following options need to be configured:
                        for your device
                        - CONFIG_USBD_PRODUCTID 0xFFFF
 
+- ULPI Layer Support:
+               The ULPI (UTMI Low Pin (count) Interface) PHYs are supported via
+               the generic ULPI layer. The generic layer accesses the ULPI PHY
+               via the platform viewport, so you need both the genric layer and
+               the viewport enabled. Currently only Chipidea/ARC based
+               viewport is supported.
+               To enable the ULPI layer support, define CONFIG_USB_ULPI and
+               CONFIG_USB_ULPI_VIEWPORT in your board configuration file.
 
 - MMC Support:
                The MMC controller on the Intel PXA is supported. To