#
-# (C) Copyright 2000 - 2009
+# (C) Copyright 2000 - 2011
#
# See file CREDITS for list of people who contributed to this
/blackfin Files generic to Analog Devices Blackfin architecture
/cpu CPU specific files
/lib Architecture specific library files
- /i386 Files generic to i386 architecture
+ /x86 Files generic to x86 architecture
/cpu CPU specific files
/lib Architecture specific library files
/m68k Files generic to m68k architecture
CONFIG_SYS_PQ2FADS - PQ2FADS-ZU or PQ2FADS-VR
CONFIG_SYS_8272ADS - MPC8272ADS
+- Marvell Family Member
+ CONFIG_SYS_MVFS - define it if you want to enable
+ multiple fs option at one time
+ for marvell soc family
+
- MPC824X Family Member (if CONFIG_MPC824X is defined)
Define exactly one of
CONFIG_MPC8240, CONFIG_MPC8245
Define this option if you want to enable the
ICache only when Code runs from RAM.
+- 85xx CPU Options:
+ CONFIG_SYS_FSL_TBCLK_DIV
+
+ Defines the core time base clock divider ratio compared to the
+ system clock. On most PQ3 devices this is 8, on newer QorIQ
+ devices it can be 16 or 32. The ratio varies from SoC to Soc.
+
+ CONFIG_SYS_FSL_PCIE_COMPAT
+
+ Defines the string to utilize when trying to match PCIe device
+ tree nodes for the given platform.
+
- Intel Monahans options:
CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO
define this to a list of base addresses for each (supported)
port. See e.g. include/configs/versatile.h
+ CONFIG_PL011_SERIAL_RLCR
+
+ Some vendor versions of PL011 serial ports (e.g. ST-Ericsson U8500)
+ have separate receive and transmit line control registers. Set
+ this variable to initialize the extra register.
+
+ CONFIG_PL011_SERIAL_FLUSH_ON_INIT
+
+ On some platforms (e.g. U8500) U-Boot is loaded by a second stage
+ boot loader that has already initialized the UART. Define this
+ variable to flush the UART at init time.
+
- Console Interface:
Depending on board, define exactly one serial port
CONFIG_CMD_BOOTD bootd
CONFIG_CMD_CACHE * icache, dcache
CONFIG_CMD_CONSOLE coninfo
+ CONFIG_CMD_CRC32 * crc32
CONFIG_CMD_DATE * support for RTC, date/time...
CONFIG_CMD_DHCP * DHCP support
CONFIG_CMD_DIAG * Diagnostics
CONFIG_CMD_EDITENV edit env variable
CONFIG_CMD_EEPROM * EEPROM read/write support
CONFIG_CMD_ELF * bootelf, bootvx
+ CONFIG_CMD_EXPORTENV * export the environment
CONFIG_CMD_SAVEENV saveenv
CONFIG_CMD_FDC * Floppy Disk Support
CONFIG_CMD_FAT * FAT partition support
CONFIG_CMD_FDOS * Dos diskette Support
CONFIG_CMD_FLASH flinfo, erase, protect
CONFIG_CMD_FPGA FPGA device initialization support
+ CONFIG_CMD_GO * the 'go' command (exec code)
+ CONFIG_CMD_GREPENV * search environment
CONFIG_CMD_HWFLOW * RTS/CTS hw flow control
CONFIG_CMD_I2C * I2C serial bus support
CONFIG_CMD_IDE * IDE harddisk support
CONFIG_CMD_IMI iminfo
CONFIG_CMD_IMLS List all found images
CONFIG_CMD_IMMAP * IMMR dump support
+ CONFIG_CMD_IMPORTENV * import an environment
CONFIG_CMD_IRQ * irqinfo
CONFIG_CMD_ITEST Integer/string test of 2 values
CONFIG_CMD_JFFS2 * JFFS2 Support
CONFIG_CMD_KGDB * kgdb
+ CONFIG_CMD_LDRINFO ldrinfo (display Blackfin loader)
CONFIG_CMD_LOADB loadb
CONFIG_CMD_LOADS loads
CONFIG_CMD_MD5SUM print md5 message digest
(requires CONFIG_CMD_MEMORY)
CONFIG_CMD_SOURCE "source" command Support
CONFIG_CMD_SPI * SPI serial bus support
+ CONFIG_CMD_TFTPSRV * TFTP transfer in server mode
CONFIG_CMD_USB * USB support
- CONFIG_CMD_VFD * VFD support (TRAB)
CONFIG_CMD_CDP * Cisco Discover Protocol support
CONFIG_CMD_FSL * Microblaze FSL support
- Watchdog:
CONFIG_WATCHDOG
If this variable is defined, it enables watchdog
- support. There must be support in the platform specific
- code for a watchdog. For the 8xx and 8260 CPUs, the
- SIU Watchdog feature is enabled in the SYPCR
- register.
+ support for the SoC. There must be support in the SoC
+ specific code for a watchdog. For the 8xx and 8260
+ CPUs, the SIU Watchdog feature is enabled in the SYPCR
+ register. When supported for a specific SoC is
+ available, then no further board specific code should
+ be needed to use it.
+
+ CONFIG_HW_WATCHDOG
+ When using a watchdog circuitry external to the used
+ SoC, then define this variable and provide board
+ specific code for the "hw_watchdog_reset" function.
- U-Boot Version:
CONFIG_VERSION_VARIABLE
CONFIG_RTC_ISL1208 - use Intersil ISL1208 RTC
CONFIG_RTC_MAX6900 - use Maxim, Inc. MAX6900 RTC
CONFIG_SYS_RTC_DS1337_NOOSC - Turn off the OSC output for DS1337
+ CONFIG_SYS_RV3029_TCR - enable trickle charger on
+ RV3029 RTC.
Note that if the RTC uses I2C, then the I2C interface
must also be configured. See I2C Support, below.
automatically converts one 32 bit word to two 16 bit
words you may also try CONFIG_SMC911X_32_BIT.
+ CONFIG_SH_ETHER
+ Support for Renesas on-chip Ethernet controller
+
+ CONFIG_SH_ETHER_USE_PORT
+ Define the number of ports to be used
+
+ CONFIG_SH_ETHER_PHY_ADDR
+ Define the ETH PHY's address
+
+ CONFIG_SH_ETHER_CACHE_WRITEBACK
+ If this option is set, the driver enables cache flush.
+
- USB Support:
At the moment only the UHCI host controller is
supported (PIP405, MIP405, MPC5200); define
and 16bpp modes defined by CONFIG_VIDEO_SED13806_8BPP
or CONFIG_VIDEO_SED13806_16BPP
+ CONFIG_FSL_DIU_FB
+ Enable the Freescale DIU video driver. Reference boards for
+ SOCs that have a DIU should define this macro to enable DIU
+ support, and should also define these other macros:
+
+ CONFIG_SYS_DIU_ADDR
+ CONFIG_VIDEO
+ CONFIG_CMD_BMP
+ CONFIG_CFB_CONSOLE
+ CONFIG_VIDEO_SW_CURSOR
+ CONFIG_VGA_AS_SINGLE_DEVICE
+ CONFIG_VIDEO_LOGO
+ CONFIG_VIDEO_BMP_LOGO
+
+ The DIU driver will look for the 'video-mode' environment
+ variable, and if defined, enable the DIU as a console during
+ boot. See the documentation file README.video for a
+ description of this variable.
+
- Keyboard Support:
CONFIG_KEYBOARD
driver in use must provide a function: mcast() to join/leave a
multicast group.
- CONFIG_BOOTP_RANDOM_DELAY
- BOOTP Recovery Mode:
CONFIG_BOOTP_RANDOM_DELAY
SPI EEPROM, also an instance works with Crystal A/D and
D/As on the SACSng board)
+ CONFIG_SH_SPI
+
+ Enables the driver for SPI controller on SuperH. Currently
+ only SH7757 is supported.
+
CONFIG_SPI_X
Enables extended (16-bit) SPI EEPROM addressing.
example, some LED's) on your board. At the moment,
the following checkpoints are implemented:
+- Standalone program support:
+ CONFIG_STANDALONE_LOAD_ADDR
+
+ This option allows to define board specific values
+ for the address where standalone program gets loaded,
+ thus overwriting the architecutre dependent default
+ settings.
+
+- Frame Buffer Address:
+ CONFIG_FB_ADDR
+
+ Define CONFIG_FB_ADDR if you want to use specific address for
+ frame buffer.
+ Then system will reserve the frame buffer address to defined address
+ instead of lcd_setmem (this function grab the memory for frame buffer
+ by panel's size).
+
+ Please see board_init_f function.
+
+ If you want this config option then,
+ please define it at your board config file
+
Legacy uImage format:
Arg Where When
Modem Support:
--------------
-[so far only for SMDK2400 and TRAB boards]
+[so far only for SMDK2400 boards]
- Modem support enable:
CONFIG_MODEM_SUPPORT
used) must be put below this limit, unless "bootm_low"
enviroment variable is defined and non-zero. In such case
all data for the Linux kernel must be between "bootm_low"
- and "bootm_low" + CONFIG_SYS_BOOTMAPSZ.
+ and "bootm_low" + CONFIG_SYS_BOOTMAPSZ. The environment
+ variable "bootm_mapsize" will override the value of
+ CONFIG_SYS_BOOTMAPSZ. If CONFIG_SYS_BOOTMAPSZ is undefined,
+ then the value in "bootm_size" will be used instead.
- CONFIG_SYS_BOOT_RAMDISK_HIGH:
Enable initrd_high functionality. If defined then the
source code. It is used to make hardware dependant
initializations.
+- CONFIG_IDE_AHB:
+ Most IDE controllers were designed to be connected with PCI
+ interface. Only few of them were designed for AHB interface.
+ When software is doing ATA command and data transfer to
+ IDE devices through IDE-AHB controller, some additional
+ registers accessing to these kind of IDE-AHB controller
+ is requierd.
+
- CONFIG_SYS_IMMR: Physical address of the Internal Memory.
DO NOT CHANGE unless you know exactly what you're
doing! (11-4) [MPC8xx/82xx systems only]
that is executed before the actual U-Boot. E.g. when
compiling a NAND SPL.
+- CONFIG_USE_ARCH_MEMCPY
+ CONFIG_USE_ARCH_MEMSET
+ If these options are used a optimized version of memcpy/memset will
+ be used if available. These functions may be faster under some
+ conditions but may increase the binary size.
+
Building the Software:
======================
for use by the bootm command. See also "bootm_size"
environment variable. Address defined by "bootm_low" is
also the base of the initial memory mapping for the Linux
- kernel -- see the description of CONFIG_SYS_BOOTMAPSZ.
+ kernel -- see the description of CONFIG_SYS_BOOTMAPSZ and
+ bootm_mapsize.
+
+ bootm_mapsize - Size of the initial memory mapping for the Linux kernel.
+ This variable is given as a hexadecimal number and it
+ defines the size of the memory region starting at base
+ address bootm_low that is accessible by the Linux kernel
+ during early boot. If unset, CONFIG_SYS_BOOTMAPSZ is used
+ as the default value if it is defined, and bootm_size is
+ used otherwise.
bootm_size - Memory range available for image processing in the bootm
command can be restricted. This variable is given as
projects / J-u-boot.git / blobdiff