common/Kconfig: Add DISPLAY_CPUINFO

[J-u-boot.git] / include / configs / meesc.h

diff --git a/include/configs/meesc.h b/include/configs/meesc.h
index 955d0e278ac6af19b86a72847a87358478ccee39..68eb01e48c924b30cc678845e43b11d33cdbe1ce 100644 (file)
--- a/include/configs/meesc.h
+++ b/include/configs/meesc.h
@@ -3,7 +3,7 @@
  * Stelian Pop <[email protected]>
  * Lead Tech Design <www.leadtechdesign.com>
  *
- * (C) Copyright 2009-2011
+ * (C) Copyright 2009-2015
  * Daniel Gorsulowski <[email protected]>
  * esd electronic system design gmbh <www.esd.eu>
  *
@@ -27,7 +27,7 @@
  * Since the linker has to swallow that define, we must use a pure
  * hex number here!
  */
-#define CONFIG_SYS_TEXT_BASE           0x20002000
+#define CONFIG_SYS_TEXT_BASE           0x21F00000
 
 /*
  * since a number of boards are not being listed in linux
@@ -53,16 +53,12 @@
 #define CONFIG_MISC_INIT_R                     /* Call misc_init_r */
 
 #define CONFIG_DISPLAY_BOARDINFO               /* call checkboard() */
-#define CONFIG_DISPLAY_CPUINFO                 /* display cpu info and speed */
 #define CONFIG_PREBOOT                         /* enable preboot variable */
 
 /*
  * Hardware drivers
  */
 
-/* required until arch/arm/include/asm/arch-at91/at91sam9263.h is reworked */
-#define ATMEL_PMC_UHP                  AT91SAM926x_PMC_UHP
-
 /* general purpose I/O */
 #define CONFIG_AT91_GPIO
 
@@ -72,9 +68,6 @@
 #define CONFIG_USART_ID                        ATMEL_ID_SYS
 #define CONFIG_BAUDRATE                        115200
 
-#define CONFIG_BOOTDELAY               3
-#define CONFIG_ZERO_BOOTDELAY_CHECK
-
 /*
  * BOOTP options
  */
@@ -86,16 +79,10 @@
 /*
  * Command line configuration.
  */
-#include <config_cmd_default.h>
-#undef CONFIG_CMD_BDI
-#undef CONFIG_CMD_FPGA
-#undef CONFIG_CMD_LOADS
-#undef CONFIG_CMD_IMLS
-
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_DHCP
+
+#ifdef CONFIG_SYS_USE_NANDFLASH
 #define CONFIG_CMD_NAND
-#define CONFIG_CMD_USB
+#endif
 
 /* LED */
 #define CONFIG_AT91_LED
@@ -104,9 +91,12 @@
  * SDRAM: 1 bank, min 32, max 128 MB
  * Initialized before u-boot gets started.
  */
+#define PHYS_SDRAM                                     ATMEL_BASE_CS1 /* 0x20000000 */
+#define PHYS_SDRAM_SIZE                                0x02000000     /* 32 MByte */
+
 #define CONFIG_NR_DRAM_BANKS           1
-#define CONFIG_SYS_SDRAM_BASE          0x20000000 /* ATMEL_BASE_CS1 */
-#define CONFIG_SYS_SDRAM_SIZE          0x02000000
+#define CONFIG_SYS_SDRAM_BASE          PHYS_SDRAM
+#define CONFIG_SYS_SDRAM_SIZE          PHYS_SDRAM_SIZE
 
 #define CONFIG_SYS_MEMTEST_START       (CONFIG_SYS_SDRAM_BASE + 0x00100000)
 #define CONFIG_SYS_MEMTEST_END         (CONFIG_SYS_SDRAM_BASE + 0x01E00000)
@@ -138,7 +128,7 @@
 #ifdef CONFIG_CMD_NAND
 # define CONFIG_NAND_ATMEL
 # define CONFIG_SYS_MAX_NAND_DEVICE            1
-# define CONFIG_SYS_NAND_BASE                  0x40000000 /* ATMEL_BASE_CS3 */
+# define CONFIG_SYS_NAND_BASE                  ATMEL_BASE_CS3 /* 0x40000000 */
 # define CONFIG_SYS_NAND_DBW_8
 # define CONFIG_SYS_NAND_MASK_ALE              (1 << 21)
 # define CONFIG_SYS_NAND_MASK_CLE              (1 << 22)
@@ -149,23 +139,9 @@
 /* Ethernet */
 #define CONFIG_MACB
 #define CONFIG_RMII
-#define CONFIG_FIT
 #define CONFIG_NET_RETRY_COUNT                 20
 #undef CONFIG_RESET_PHY_R
 
-/* USB */
-#define CONFIG_USB_ATMEL
-#define CONFIG_USB_ATMEL_CLK_SEL_PLLB
-#define CONFIG_USB_OHCI_NEW
-#define CONFIG_DOS_PARTITION
-#define CONFIG_SYS_USB_OHCI_CPU_INIT
-#define CONFIG_SYS_USB_OHCI_REGS_BASE          0x00a00000
-#define CONFIG_SYS_USB_OHCI_SLOT_NAME          "at91sam9263"
-#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS     2
-
-/* CAN */
-#define CONFIG_AT91_CAN
-
 /* hw-controller addresses */
 #define CONFIG_ET1100_BASE             0x70000000
 
@@ -195,6 +171,7 @@
                                        sizeof(CONFIG_SYS_PROMPT) + 16)
 #define CONFIG_SYS_LONGHELP
 #define CONFIG_CMDLINE_EDITING
+#define CONFIG_AUTO_COMPLETE
 
 /*
  * Size of malloc() pool