* Provide extended interface to Linux boot loader
* S-Record download
* network boot
- * PCMCIA / CompactFlash / ATA disk / SCSI ... boot
+ * ATA disk / SCSI ... boot
- create ARMBoot project (http://sourceforge.net/projects/armboot)
- add other CPU families (starting with ARM)
- create U-Boot project (http://sourceforge.net/projects/u-boot)
specific to be undertaken on a native platform. The sandbox is also used to
run some of U-Boot's tests.
-See board/sandbox/README.sandbox for more details.
+See doc/arch/index.rst for more details.
Board Initialisation Flow:
- preloader_console_init() can be called here in extremis
- should set up SDRAM, and anything needed to make the UART work
- these is no need to clear BSS, it will be done by crt0.S
+ - for specific scenarios on certain architectures an early BSS *can*
+ be made available (via CONFIG_SPL_EARLY_BSS by moving the clearing
+ of BSS prior to entering board_init_f()) but doing so is discouraged.
+ Instead it is strongly recommended to architect any code changes
+ or additions such to not depend on the availability of BSS during
+ board_init_f() as indicated in other sections of this README to
+ maintain compatibility and consistency across the entire code base.
- must return normally from this function (don't call board_init_r()
directly)
CONFIG_SH_ETHER_CACHE_WRITEBACK
If this option is set, the driver enables cache flush.
-- PWM Support:
- CONFIG_PWM_IMX
- Support for PWM module on the imx6.
-
- TPM Support:
CONFIG_TPM
Support TPM devices.
A better solution is to properly configure the firewall,
but sometimes that is not allowed.
-- Show boot progress:
- CONFIG_SHOW_BOOT_PROGRESS
-
- Defining this option allows to add some board-
- specific code (calling a user-provided function
- "show_boot_progress(int)") that enables you to show
- the system's boot progress on some display (for
- example, some LED's) on your board. At the moment,
- the following checkpoints are implemented:
-
-
-Legacy uImage format:
-
- Arg Where When
- 1 common/cmd_bootm.c before attempting to boot an image
- -1 common/cmd_bootm.c Image header has bad magic number
- 2 common/cmd_bootm.c Image header has correct magic number
- -2 common/cmd_bootm.c Image header has bad checksum
- 3 common/cmd_bootm.c Image header has correct checksum
- -3 common/cmd_bootm.c Image data has bad checksum
- 4 common/cmd_bootm.c Image data has correct checksum
- -4 common/cmd_bootm.c Image is for unsupported architecture
- 5 common/cmd_bootm.c Architecture check OK
- -5 common/cmd_bootm.c Wrong Image Type (not kernel, multi)
- 6 common/cmd_bootm.c Image Type check OK
- -6 common/cmd_bootm.c gunzip uncompression error
- -7 common/cmd_bootm.c Unimplemented compression type
- 7 common/cmd_bootm.c Uncompression OK
- 8 common/cmd_bootm.c No uncompress/copy overwrite error
- -9 common/cmd_bootm.c Unsupported OS (not Linux, BSD, VxWorks, QNX)
-
- 9 common/image.c Start initial ramdisk verification
- -10 common/image.c Ramdisk header has bad magic number
- -11 common/image.c Ramdisk header has bad checksum
- 10 common/image.c Ramdisk header is OK
- -12 common/image.c Ramdisk data has bad checksum
- 11 common/image.c Ramdisk data has correct checksum
- 12 common/image.c Ramdisk verification complete, start loading
- -13 common/image.c Wrong Image Type (not PPC Linux ramdisk)
- 13 common/image.c Start multifile image verification
- 14 common/image.c No initial ramdisk, no multifile, continue.
-
- 15 arch/<arch>/lib/bootm.c All preparation done, transferring control to OS
-
- -30 arch/powerpc/lib/board.c Fatal error, hang the system
- -31 post/post.c POST test failed, detected by post_output_backlog()
- -32 post/post.c POST test failed, detected by post_run_single()
-
- 34 common/cmd_doc.c before loading a Image from a DOC device
- -35 common/cmd_doc.c Bad usage of "doc" command
- 35 common/cmd_doc.c correct usage of "doc" command
- -36 common/cmd_doc.c No boot device
- 36 common/cmd_doc.c correct boot device
- -37 common/cmd_doc.c Unknown Chip ID on boot device
- 37 common/cmd_doc.c correct chip ID found, device available
- -38 common/cmd_doc.c Read Error on boot device
- 38 common/cmd_doc.c reading Image header from DOC device OK
- -39 common/cmd_doc.c Image header has bad magic number
- 39 common/cmd_doc.c Image header has correct magic number
- -40 common/cmd_doc.c Error reading Image from DOC device
- 40 common/cmd_doc.c Image header has correct magic number
- 41 common/cmd_ide.c before loading a Image from a IDE device
- -42 common/cmd_ide.c Bad usage of "ide" command
- 42 common/cmd_ide.c correct usage of "ide" command
- -43 common/cmd_ide.c No boot device
- 43 common/cmd_ide.c boot device found
- -44 common/cmd_ide.c Device not available
- 44 common/cmd_ide.c Device available
- -45 common/cmd_ide.c wrong partition selected
- 45 common/cmd_ide.c partition selected
- -46 common/cmd_ide.c Unknown partition table
- 46 common/cmd_ide.c valid partition table found
- -47 common/cmd_ide.c Invalid partition type
- 47 common/cmd_ide.c correct partition type
- -48 common/cmd_ide.c Error reading Image Header on boot device
- 48 common/cmd_ide.c reading Image Header from IDE device OK
- -49 common/cmd_ide.c Image header has bad magic number
- 49 common/cmd_ide.c Image header has correct magic number
- -50 common/cmd_ide.c Image header has bad checksum
- 50 common/cmd_ide.c Image header has correct checksum
- -51 common/cmd_ide.c Error reading Image from IDE device
- 51 common/cmd_ide.c reading Image from IDE device OK
- 52 common/cmd_nand.c before loading a Image from a NAND device
- -53 common/cmd_nand.c Bad usage of "nand" command
- 53 common/cmd_nand.c correct usage of "nand" command
- -54 common/cmd_nand.c No boot device
- 54 common/cmd_nand.c boot device found
- -55 common/cmd_nand.c Unknown Chip ID on boot device
- 55 common/cmd_nand.c correct chip ID found, device available
- -56 common/cmd_nand.c Error reading Image Header on boot device
- 56 common/cmd_nand.c reading Image Header from NAND device OK
- -57 common/cmd_nand.c Image header has bad magic number
- 57 common/cmd_nand.c Image header has correct magic number
- -58 common/cmd_nand.c Error reading Image from NAND device
- 58 common/cmd_nand.c reading Image from NAND device OK
-
- -60 common/env_common.c Environment has a bad CRC, using default
-
- 64 net/eth.c starting with Ethernet configuration.
- -64 net/eth.c no Ethernet found.
- 65 net/eth.c Ethernet found.
-
- -80 common/cmd_net.c usage wrong
- 80 common/cmd_net.c before calling net_loop()
- -81 common/cmd_net.c some error in net_loop() occurred
- 81 common/cmd_net.c net_loop() back without error
- -82 common/cmd_net.c size == 0 (File with size 0 loaded)
- 82 common/cmd_net.c trying automatic boot
- 83 common/cmd_net.c running "source" command
- -83 common/cmd_net.c some error in automatic boot or "source" command
- 84 common/cmd_net.c end without errors
-
-FIT uImage format:
-
- Arg Where When
- 100 common/cmd_bootm.c Kernel FIT Image has correct format
- -100 common/cmd_bootm.c Kernel FIT Image has incorrect format
- 101 common/cmd_bootm.c No Kernel subimage unit name, using configuration
- -101 common/cmd_bootm.c Can't get configuration for kernel subimage
- 102 common/cmd_bootm.c Kernel unit name specified
- -103 common/cmd_bootm.c Can't get kernel subimage node offset
- 103 common/cmd_bootm.c Found configuration node
- 104 common/cmd_bootm.c Got kernel subimage node offset
- -104 common/cmd_bootm.c Kernel subimage hash verification failed
- 105 common/cmd_bootm.c Kernel subimage hash verification OK
- -105 common/cmd_bootm.c Kernel subimage is for unsupported architecture
- 106 common/cmd_bootm.c Architecture check OK
- -106 common/cmd_bootm.c Kernel subimage has wrong type
- 107 common/cmd_bootm.c Kernel subimage type OK
- -107 common/cmd_bootm.c Can't get kernel subimage data/size
- 108 common/cmd_bootm.c Got kernel subimage data/size
- -108 common/cmd_bootm.c Wrong image type (not legacy, FIT)
- -109 common/cmd_bootm.c Can't get kernel subimage type
- -110 common/cmd_bootm.c Can't get kernel subimage comp
- -111 common/cmd_bootm.c Can't get kernel subimage os
- -112 common/cmd_bootm.c Can't get kernel subimage load address
- -113 common/cmd_bootm.c Image uncompress/copy overwrite error
-
- 120 common/image.c Start initial ramdisk verification
- -120 common/image.c Ramdisk FIT image has incorrect format
- 121 common/image.c Ramdisk FIT image has correct format
- 122 common/image.c No ramdisk subimage unit name, using configuration
- -122 common/image.c Can't get configuration for ramdisk subimage
- 123 common/image.c Ramdisk unit name specified
- -124 common/image.c Can't get ramdisk subimage node offset
- 125 common/image.c Got ramdisk subimage node offset
- -125 common/image.c Ramdisk subimage hash verification failed
- 126 common/image.c Ramdisk subimage hash verification OK
- -126 common/image.c Ramdisk subimage for unsupported architecture
- 127 common/image.c Architecture check OK
- -127 common/image.c Can't get ramdisk subimage data/size
- 128 common/image.c Got ramdisk subimage data/size
- 129 common/image.c Can't get ramdisk load address
- -129 common/image.c Got ramdisk load address
-
- -130 common/cmd_doc.c Incorrect FIT image format
- 131 common/cmd_doc.c FIT image format OK
-
- -140 common/cmd_ide.c Incorrect FIT image format
- 141 common/cmd_ide.c FIT image format OK
-
- -150 common/cmd_nand.c Incorrect FIT image format
- 151 common/cmd_nand.c FIT image format OK
-
-- Standalone program support:
CONFIG_STANDALONE_LOAD_ADDR
This option defines a board specific value for the
allowed for use by the bootm command. See also "bootm_low"
environment variable.
+ bootstopkeysha256, bootdelaykey, bootstopkey - See README.autoboot
+
updatefile - Location of the software update file on a TFTP server, used
by the automatic software update feature. Please refer to
documentation in doc/README.update for more details.
projects / J-u-boot.git / blobdiff