configs: Migrate CMD_NAND*

[J-u-boot.git] / include / configs / at91sam9260ek.h

diff --git a/include/configs/at91sam9260ek.h b/include/configs/at91sam9260ek.h
index d7fd6b089c1d1bc4a93ba2f750f91daa8e094855..00efcf032d40f80e22429540ce6f32aa31e4df19 100644 (file)
--- a/include/configs/at91sam9260ek.h
+++ b/include/configs/at91sam9260ek.h
@@ -28,7 +28,6 @@
 /* ARM asynchronous clock */
 #define CONFIG_SYS_AT91_SLOW_CLOCK     32768           /* slow clock xtal */
 #define CONFIG_SYS_AT91_MAIN_CLOCK     18432000        /* main clock xtal */
-#define CONFIG_SYS_HZ                  1000
 
 /* Define actual evaluation board type from used processor type */
 #ifdef CONFIG_AT91SAM9G20
@@ -43,29 +42,9 @@
 #define CONFIG_SETUP_MEMORY_TAGS
 #define CONFIG_INITRD_TAG
 #define CONFIG_SKIP_LOWLEVEL_INIT
-#define CONFIG_BOARD_EARLY_INIT_F
-#define CONFIG_DISPLAY_CPUINFO
-
-#define CONFIG_CMD_BOOTZ
-#define CONFIG_OF_LIBFDT
 
 /* general purpose I/O */
 #define CONFIG_ATMEL_LEGACY            /* required until (g)pio is fixed */
-#define CONFIG_AT91_GPIO
-#define CONFIG_AT91_GPIO_PULLUP        1       /* keep pullups on peripheral pins */
-
-/* serial console */
-#define CONFIG_ATMEL_USART
-#define CONFIG_USART_BASE              ATMEL_BASE_DBGU
-#define        CONFIG_USART_ID                 ATMEL_ID_SYS
-#define CONFIG_BAUDRATE                        115200
-
-/* LED */
-#define CONFIG_AT91_LED
-#define        CONFIG_RED_LED          AT91_PIN_PA9    /* this is the power led */
-#define        CONFIG_GREEN_LED        AT91_PIN_PA6    /* this is the user led */
-
-#define CONFIG_BOOTDELAY       3
 
 /*
  * BOOTP options
@@ -75,24 +54,6 @@
 #define CONFIG_BOOTP_GATEWAY           1
 #define CONFIG_BOOTP_HOSTNAME          1
 
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-#undef CONFIG_CMD_BDI
-#undef CONFIG_CMD_FPGA
-#undef CONFIG_CMD_IMI
-#undef CONFIG_CMD_IMLS
-#undef CONFIG_CMD_LOADS
-#undef CONFIG_CMD_SOURCE
-
-#define CONFIG_CMD_PING                1
-#define CONFIG_CMD_DHCP                1
-#define CONFIG_CMD_NAND                1
-#define CONFIG_CMD_MMC
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_USB         1
-
 /*
  * SDRAM: 1 bank, min 32, max 128 MB
  * Initialized before u-boot gets started.
@@ -108,10 +69,10 @@
  */
 #ifdef CONFIG_AT91SAM9XE
 # define CONFIG_SYS_INIT_SP_ADDR \
-       (ATMEL_BASE_SRAM + 0x1000 - GENERATED_GBL_DATA_SIZE)
+       (ATMEL_BASE_SRAM + 16 * 1024 - GENERATED_GBL_DATA_SIZE)
 #else
 # define CONFIG_SYS_INIT_SP_ADDR \
-       (ATMEL_BASE_SRAM1 + 0x1000 - GENERATED_GBL_DATA_SIZE)
+       (ATMEL_BASE_SRAM1 + 16 * 1024 - GENERATED_GBL_DATA_SIZE)
 #endif
 
 /*
@@ -132,15 +93,16 @@
 # define CONFIG_MACH_TYPE MACH_TYPE_AT91SAM9260EK
 #endif
 
-/* DataFlash */
 #ifndef CONFIG_AT91SAM9G20EK_2MMC
+/* DataFlash */
 #define CONFIG_ATMEL_DATAFLASH_SPI
 #define CONFIG_HAS_DATAFLASH           1
-#define CONFIG_SYS_SPI_WRITE_TOUT              (5*CONFIG_SYS_HZ)
 #define CONFIG_SYS_MAX_DATAFLASH_BANKS         2
 #define CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0    0xC0000000      /* CS0 */
 #define CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS1    0xD0000000      /* CS1 */
 #define AT91_SPI_CLK                   15000000
+#else
+/* Enable MMC. The MCCK is conflicted with DataFlash */
 #endif
 
 #ifdef CONFIG_AT91SAM9G20EK
@@ -162,35 +124,14 @@
 #define CONFIG_SYS_NAND_READY_PIN      AT91_PIN_PC13
 #endif
 
-/* MMC */
-#ifdef CONFIG_CMD_MMC
-#define CONFIG_MMC
-#define CONFIG_GENERIC_MMC
-#define CONFIG_GENERIC_ATMEL_MCI
-#endif
-
-/* FAT */
-#ifdef CONFIG_CMD_FAT
-#define CONFIG_DOS_PARTITION
-#endif
-
-/* NOR flash - no real flash on this board */
-#define CONFIG_SYS_NO_FLASH                    1
-
-/* Ethernet */
-#define CONFIG_MACB                    1
-#define CONFIG_RMII                    1
-#define CONFIG_NET_RETRY_COUNT         20
-#define CONFIG_RESET_PHY_R             1
-
 /* USB */
 #define CONFIG_USB_ATMEL
+#define CONFIG_USB_ATMEL_CLK_SEL_PLLB
 #define CONFIG_USB_OHCI_NEW            1
 #define CONFIG_SYS_USB_OHCI_CPU_INIT           1
 #define CONFIG_SYS_USB_OHCI_REGS_BASE          0x00500000      /* AT91SAM9260_UHP_BASE */
 #define CONFIG_SYS_USB_OHCI_SLOT_NAME          "at91sam9260"
 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS     2
-#define CONFIG_USB_STORAGE             1
 
 #define CONFIG_SYS_LOAD_ADDR                   0x22000000      /* load address */
 
@@ -200,7 +141,6 @@
 #ifdef CONFIG_SYS_USE_DATAFLASH_CS0
 
 /* bootstrap + u-boot + env + linux in dataflash on CS0 */
-#define CONFIG_ENV_IS_IN_DATAFLASH     1
 #define CONFIG_SYS_MONITOR_BASE        (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 + 0x8400)
 #define CONFIG_ENV_OFFSET              0x4200
 #define CONFIG_ENV_ADDR                (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 + CONFIG_ENV_OFFSET)
@@ -214,7 +154,6 @@
 #elif CONFIG_SYS_USE_DATAFLASH_CS1
 
 /* bootstrap + u-boot + env + linux in dataflash on CS1 */
-#define CONFIG_ENV_IS_IN_DATAFLASH     1
 #define CONFIG_SYS_MONITOR_BASE        (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS1 + 0x8400)
 #define CONFIG_ENV_OFFSET              0x4200
 #define CONFIG_ENV_ADDR                (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS1 + CONFIG_ENV_OFFSET)
@@ -228,8 +167,7 @@
 #elif defined(CONFIG_SYS_USE_NANDFLASH)
 
 /* bootstrap + u-boot + env + linux in nandflash */
-#define CONFIG_ENV_IS_IN_NAND  1
-#define CONFIG_ENV_OFFSET              0xc0000
+#define CONFIG_ENV_OFFSET              0x120000
 #define CONFIG_ENV_OFFSET_REDUND       0x100000
 #define CONFIG_ENV_SIZE                0x20000         /* 1 sector = 128 kB */
 #define CONFIG_BOOTCOMMAND     "nand read 0x22000000 0x200000 0x300000; bootm"
@@ -242,7 +180,6 @@
 
 #else  /* CONFIG_SYS_USE_MMC */
 /* bootstrap + u-boot + env + linux in mmc */
-#define CONFIG_ENV_IS_IN_MMC
 /* For FAT system, most cases it should be in the reserved sector */
 #define CONFIG_ENV_OFFSET              0x2000
 #define CONFIG_ENV_SIZE                        0x1000
@@ -258,10 +195,8 @@
        "root=/dev/mmcblk0p2 rw rootfstype=ext4 rootwait"
 #endif
 
-#define CONFIG_SYS_PROMPT              "U-Boot> "
 #define CONFIG_SYS_CBSIZE              256
 #define CONFIG_SYS_MAXARGS             16
-#define CONFIG_SYS_PBSIZE              (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 #define CONFIG_SYS_LONGHELP            1
 #define CONFIG_CMDLINE_EDITING 1
 #define CONFIG_AUTO_COMPLETE