Move PHYLIB to Kconfig

[J-u-boot.git] / include / configs / taurus.h

diff --git a/include/configs/taurus.h b/include/configs/taurus.h
index 0b05289d07e6ffbbc218a402c8813475f87f38a4..5a7ef75ae928f2dcd0e3f74590ed60b5a0719a54 100644 (file)
--- a/include/configs/taurus.h
+++ b/include/configs/taurus.h
@@ -23,7 +23,6 @@
 #include <linux/sizes.h>
 
 #if defined(CONFIG_SPL_BUILD)
-#define CONFIG_SYS_THUMB_BUILD
 #define CONFIG_SYS_ICACHE_OFF
 #define CONFIG_SYS_DCACHE_OFF
 #endif
@@ -45,9 +44,7 @@
 #define CONFIG_CMDLINE_TAG             /* enable passing of ATAGs */
 #define CONFIG_SETUP_MEMORY_TAGS
 #define CONFIG_INITRD_TAG
-#define CONFIG_SKIP_LOWLEVEL_INIT
-#define CONFIG_BOARD_EARLY_INIT_F
-#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_SKIP_LOWLEVEL_INIT_ONLY
 
 /* general purpose I/O */
 #define CONFIG_ATMEL_LEGACY            /* required until (g)pio is fixed */
@@ -58,14 +55,8 @@
 #define CONFIG_ATMEL_USART
 #define CONFIG_USART_BASE              ATMEL_BASE_DBGU
 #define CONFIG_USART_ID                        ATMEL_ID_SYS
-#define CONFIG_BAUDRATE                        115200
 
 
-/*
- * Command line configuration.
- */
-#define CONFIG_CMD_NAND
-
 /*
  * SDRAM: 1 bank, min 32, max 128 MB
  * Initialized before u-boot gets started.
@@ -94,9 +85,6 @@
 #define CONFIG_SYS_NAND_READY_PIN      AT91_PIN_PC13
 #endif
 
-/* NOR flash - no real flash on this board */
-#define CONFIG_SYS_NO_FLASH                    1
-
 /* Ethernet */
 #define CONFIG_MACB
 #define CONFIG_RMII
@@ -118,22 +106,16 @@
 #define CONFIG_SYS_USB_OHCI_REGS_BASE          0x00500000
 #define CONFIG_SYS_USB_OHCI_SLOT_NAME          "at91sam9260"
 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS     2
-#define CONFIG_USB_STORAGE
 
 /* USB DFU support */
-#define CONFIG_CMD_MTDPARTS
 #define CONFIG_MTD_DEVICE
 #define CONFIG_MTD_PARTITIONS
 
 #define CONFIG_USB_GADGET_AT91
 
 /* DFU class support */
-#define CONFIG_USB_FUNCTION_DFU
-#define CONFIG_DFU_NAND
 #define CONFIG_SYS_DFU_DATA_BUF_SIZE   (SZ_1M)
 #define DFU_MANIFEST_POLL_TIMEOUT      25000
-
-#define CONFIG_SYS_CACHELINE_SIZE      SZ_8K
 #endif
 
 /* SPI EEPROM */
@@ -144,9 +126,6 @@
 
 #if defined(CONFIG_SPL_BUILD)
 /* SPL related */
-#undef CONFIG_SPL_OS_BOOT              /* Not supported by existing map */
-#define CONFIG_SPL_SPI_SUPPORT
-#define CONFIG_SPL_SPI_FLASH_SUPPORT
 #define CONFIG_SPL_SPI_LOAD
 #define CONFIG_SYS_SPI_U_BOOT_OFFS     0x20000
 
@@ -159,7 +138,6 @@
 #define CONFIG_SYS_LOAD_ADDR                   0x22000000
 
 /* bootstrap in spi flash , u-boot + env + linux in nandflash */
-#define CONFIG_ENV_IS_IN_NAND
 #define CONFIG_ENV_OFFSET              0x100000
 #define CONFIG_ENV_OFFSET_REDUND       0x180000
 #define CONFIG_ENV_SIZE                (SZ_128K)       /* 1 sector = 128 kB */
@@ -260,14 +238,7 @@
 #define CONFIG_SPL_BSS_START_ADDR      CONFIG_SPL_MAX_SIZE
 #define CONFIG_SPL_BSS_MAX_SIZE                (3 * SZ_512)
 
-#define CONFIG_SPL_LIBCOMMON_SUPPORT
-#define CONFIG_SPL_LIBGENERIC_SUPPORT
-#define CONFIG_SPL_SERIAL_SUPPORT
-
-#define CONFIG_SPL_BOARD_INIT
-#define CONFIG_SPL_GPIO_SUPPORT
 #define CONFIG_SYS_NAND_ENABLE_PIN_SPL (2*32 + 14)
-#define CONFIG_SPL_NAND_SUPPORT
 #define CONFIG_SYS_USE_NANDFLASH       1
 #define CONFIG_SPL_NAND_DRIVERS
 #define CONFIG_SPL_NAND_BASE